DT-RLC. User Manual. Lock/Light Control Interface

Transcription

1 Lock/Light Control Interface User Manual WIRE SYSTEM V S INUSE Please read this manual carefully before using the product you purchase, and keep it well for future use.we reserve the right to modify the specification in this manual at any time without notice.

2 .About Interface Description: The relay actuator is an accessory device designed for DT system to control door locks and/or light. It has following features: Two work modes: lock control mode and light control mode; Allows to open gate door locks or control lights; Support high powerconsumption lock; Configurable unlock timed output or light control timed output; Support : when in lock control mode, the exit button operating the lock; when in light control mode, the exit button operating the light. Parts V S WIRE SYSTEM Lock Control Jumper V S INUSE INUSE V: V power output. Can be used to power PowerontoOpen Electic lock max holding current 450mA S: Reserved : Exit button contact. Short and to unlock or control light : The common Ground of the other contacts:, S and V

3 :The normallyclosed contact to : The common contact of the unlock/light relay : The normallyopen contact to Lock Control Jumper: To select the lock type: see section 5., 5.4 :Working indicator, it will light up when powered IN USE:Unlock/light indicator, lights up when unlock or turn on the light Bus:Connect to the bus line, no polarity :Used for setting the address of the RLC. Unit Mounting WIRE SYSTEM V S INUSE DIN Rail Mounting 4. How To Set The Work Mode Factory default is Lock Control Mode ).Set =, =, = OFF, Short and and will go into the setting mode; ).Struck repeatedly 4x times to switch work modes: A. INUSE indicator flashes once means Interface in the light control mode B. INUSE indicator flashes two times means Interface in the lock control mode ).When the setting complete it will restart automatically Please note the setting state valid within 5 seconds. If more than 5 seconds without any action taken setting mode exits automatically

4 5. Lock Control Mode In lock control mode, the allows to open gate door locks; Support high powerconsumption lock; With configurable unlock timed output; Support 5. How to set the unlock time In lock control mode: ). Poweron and within 5 seconds, shortcircuit and S until INUSE indicator flashes ). Shortcircuit and until INUSE indicator lights up ). Shortcircuit and S and start counting flashes. INUSE indicator flashes once per second. The maximum unlocking time is 0 seconds 4). When desired time reached, remove shortcircuit. Time will be saved automatically 5. switches settings for lock The switches at the back are used to set the address of the RLC. Please refer to the following tables: State Descriptions OFF,OFF,OFF Applies to door station & lock OFF,OFF, Applies to door station & lock,off,off Applies to door station & lock,off, Applies to door station & lock OFF,,OFF Applies to door station & lock

5 INUSE V S WIRE SYSTEM V S State Descriptions OFF,, Applies to door station & lock,,off Applies to door station 4 & lock,, Applies to door station 4 & lock 5. Lock powered by RLC (only for PowerontoOpen lock) maximum holding current is 450mA controls the second lock (Electric) of door station Electriclock AC~ # Camera (Address:0) monitor PC6 (IM) (DS) L L PL S S 4

6 INUSE V S WIRE SYSTEM V S Closeup Connection Note:. When Electric lock connected, the jumper position in. When Emagnetic lock connected, the jumper position in Electriclock * V S Jumper position in 5.4 Lock Powered with extra Power supply A. PowerontoOpen: controls the second lock (Electric) of door station adaptor for the lock Elock AC~ # Camera (Address:0) monitor PC6 (IM) (DS) L L PL S S 5

7 INUSE V S WIRE SYSTEM V S Closeup Connection. Electric Lock Elock SUPPLY * V S Jumper position in B.PowerofftoOpen: controls the second lock (magnetic) of door station adaptor for the lock EMlock AC~ # Camera (Address:0) monitor PC6 (IM) (DS) L L PL S S 6

8 Closeup Connection. Magnetic Lock SUPPLY EMLOCK * V S Jumper position in 6. Light Control Mode In light control mode, the allows to control lights with configurable time output; Support 6. How to set the light working time In light control mode: ). Poweron and within 5 seconds, shortcircuit and S until INUSE indicator flashes ). Shortcircuit and until INUSE indicator lights up ). Shortcircuit and S and start counting flashes. INUSE indicator flashes once per second= equals 0 sec of light On. The maximum time light can stay On is 900 sec 4). When desired time reached, remove shortcircuit. Time will be saved automatically 6. switches settings for light Bit State Descriptions OFF,OFF,OFF Set for the first 7

9 INUSE V S WIRE SYSTEM V S Bit State Descriptions OFF,OFF, Set for the second,off,off Set for the third,off, Set for the fourth OFF,,OFF Set for the fifth OFF,, Set for the sixth,,off Set for the seventh,, Set for the eighth 6. Connection for Light Control 0~50V AC Input AC~ (Address:0) monitor PC6 (IM) (DS) L L PL S S 8

10 INUSE INUSE V S V S RF CARD 7. Connecting s In one system, you can connect a to control gate door lock, and connect another to control light adaptor for the lock Elock Safety Type: poweron to open poweroff to lock 0~50V AC Input AC~ N N L SW LED PC6 (IM) (DS) monitor (Address:0) 9

11 8. Specifications Power Supply : DC4V Unlocking Time: ~0s (Default s) Lock Power supply: Vdc, 450mA (Internal Power) Working Temperature: 0 0 C~40 0 C Dimension: H89 W7 D45mm The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved. DTENGRLCV 05096