DT-RLC. User Manual. Relay actuator

Transcription

1 Relay actuator User Manual WIRE SYSTEM COM NC V S S INUSE RISER Please read this manual carefully before using the product you purchase, and keep it well for future use.we reserve the right to modify the specification in this manual at any time without notice.

2 .About Unit Discription: The relay actuator is a unlock function device designed for DT system to control door locks. It has the features as follows: Allows to open gate door locks; Support high powerconsumption lock; With configurable unlock timed output; Support exit control button.. Parts and Name NC COM V S S WIRE SYSTEM lock Control Jumper COM NC V S S RISER INUSE INUSE V:V power output. Can be used to power the lock. S:Reserved. S:Exit button contact. Short this contact and the to unlock. :The common Ground of the other contacts: S, S and V.

3 NC:The normallyclosed contact to COM. COM: The common contact of the unlock relay. : The normallyopen contact to COM. Lock Control Jumper: To select the lock type: see section 5,6. :Working indicator,it will light up when plugs in power supply. INUSE:Unlock indicator,it will light up when unlock. Bus:Connect to the bus line, no polarity. :Used for setting the address of the RLC.. Unit Mounting WIRE SYSTEM COM NC V S S INUSE RISER DIN Rail Mounting. How to set the unlock delay time ). Poweron within 5 seconds, shortcircuit S up to seconds, the INUSE indicator flash. ). Shortcircuit S up to seconds, and the INUSE indicator always light. ). Shortcircuit again S, at this time,the shortcircuit time equal to unlock delay time. (the INUSE indicator flashes once per second, Less than two seconds by one second calculation; The maximum setting time is 0 seconds.) 4). After S released, saved unlock delay, and exit the setting.

4 4. Switch Setting The switch in the back of the panel is used to set the address of the RLC. Please refer to the followings for more detail informations about the settings: settings for lock. Bit State Descriptions OFF,OFF,OFF Applies to door station & lock OFF,OFF, Applies to door station & lock,off,off Applies to door station & lock,off, Applies to door station & lock OFF,,OFF Applies to door station & lock OFF,, Applies to door station & lock,,off Applies to door station4 & lock,, Applies to door station4 & lock

5 COM COM NC INUSE NC V S S WIRE SYSTEM V S S RISER 5. Internal powered lock connection(only suitable for Powerontounlock type) control the second lock of door station Elock AC~ # Camera (Device Address:0) monitor PC6 (IM) (DS) L L PL S S connect lock Note:. When connect Electronic lock, the jumper position in. Jumper position in. When connect Emagnetic lock, the jumper position in. Elock * COM NC V S S 4

6 COM COM NC INUSE NC V S S WIRE SYSTEM V S S RISER 6. External Power Supply powered lock connection A. Powerontounlock type: control the second lock of door station adaptor for the lock Elock AC~ # Camera (Device Address:0) monitor PC6 (IM) (DS) L L PL S S connect lock Note:. Here's lock type is Electronic lock. Elock SUPPLY * COM NC V S S 5

7 COM COM NC INUSE NC V S S WIRE SYSTEM V S S RISER B.Powerofftounlock type: control the second lock of door station adaptor for the lock EMlock AC~ # Camera (Device Address:0) monitor PC6 (IM) (DS) L L PL S S connect lock Note:. Here's lock type is Emagnetic lock. SUPPLY EMLOCK * COM NC V S S 6

8 7. Specification Power Supply : DC4V; Unlocking Time: ~0s(Default s); Lock Power supply: Vdc, 450mA(Internal Power); Working Temperature: 0 0 C~40 0 C; Dimension: 89(H) 7(W) 45(D)mm. The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved. DTENGRLCV 04075