Petrel TIPS&TRICKS from SCM
|
|
- Robert Watts
- 5 years ago
- Views:
Transcription
1 Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Smoothing 2D Grids in Petrel 2D Grids are the foundation of much of the work done in Petrel. They are used for display, volume calculations, input for building structural frameworks, as trends to control geocellular modeling, and much more. Often the form of grids, when initially built, contains roughness related to noisy data and that roughness needs to be smoothed before the grid can be used. In Petrel there are a variety of tools for smoothing 2D Grids. These tools are found in a number of places and a thorough knowledge of their location and use will ensure that you create the best possible grid in the most efficient manner. Smoothing is done by algorithms called filters applied at grid nodes. Filters work in many ways. One type of filter tosses out the value of the node it is centered on and uses the nearest circle of node values around the center node to calculate a new value for the one discarded. To make the filter more aggressive, additional circles of node values farther from its center are used in the calculation. The filter is moved over all nodes selected for smoothing and the same operation is performed at each. Petrel s smoothing algorithm probably does not work exactly as described here, but the analogy will help you understand how the algorithm approaches the smoothing process. Four methods are commonly used to apply the smoothing filter to 2D Grids in Petrel. They are: Smoothing during grid construction Operation smoothing Polygon constrained operation smoothing Interactive smoothing These four methods are described below. Smoothing During Grid Construction As mentioned above, data are typically the source of grid roughness. Seismic interpretation data will often contain a high frequency noise that is passed to the grid, given a sufficiently fine grid increment. This noise is usually removed with a general smoother applied uniformly to the entire grid. In most mapping systems this is done as an additional operation step after the grid is built. However, in Petrel, this uniform smoothing can be done as a post processing step (Post proc tab) during grid construction (Make/edit surface process). Implement the Post Process smoothing initially with one iteration, display the resulting grid in a 3D Window, and then rerun the Make/edit surface process using different numbers of iterations until the desired amount of smoothing is achieved. 1
2 Figure: Seismic data gridded without (left) and with (right) post process smoothing. Figure: Post Processing step used to smooth a grid. It is possible to apply a hard clip in the same Post proc tab of Make/edit surface. This might be used to clip a N:G surface to a maximum value of 1.0 and minimum value of 0.0. Smoothing can be applied before and/or after the hard clip. If applied after the hard clip, the smoothing effect is to round the sharp truncation edge. The beauty of this post truncation smoothing is that the smoothed values still honor the truncation and do not project above or below the limits. Operation Smoothing Operations based smoothing is the most commonly used method for smoothing a 2D Grid. The 2D Grid already exists, and is displayed in a 3D Window so the effect of smoothing can be seen. The operation is reached by opening the Settings dialog for the 2D Grid and going to either the More tab or the Operations tab. In the More tab, smoothing is at the top of the dialog. In the Operations tab, smoothing is found in the Surface operations folder. Both offer the same functionality. Two parameters control smoothing, Number of Iterations and Filter width. Number of Iterations is the equivalent of hitting the Run button as many times as the number of iterations. Because there is only one Undo for an operation, this multiple execution is very useful. You can try one iteration, undo it, try two iterations, undo it, and so on until the surface has an acceptable form. The Filter width parameter controls the size of the feature that gets smoothed out. The feature size can be thought of in grid increments with the filter centered on the grid node. A width of 1 will extend out one grid increment from the node, 2 will extend two grid increments, and 2
3 so on. Remember that the filter moves from node to node on the grid, therefore, when the filter width is large it will have considerable overlap on adjacent nodes. This means that large filter widths can be very aggressive in the amount of smoothing they do. Again, display the grid in a 3D Window and use the Undo button to test a variety of filter widths until you reach the desired affect. Figure: Operations and More tabs showing where smoothing is found. Figure: Example of smoothing a surface with operations. The original surface (top left), Smoothed with 1 iteration and 1 filter width (top right), smoothed with 3 iterations and 1 filter width (bottom left), smoothed with 1 iteration and 3 filter width (bottom right). 3
4 Polygon Constrained Operation Smoothing Polygon Constrained Operation Smoothing is a smoothing method that should be used a lot more than it is. The technique smoothes only inside or outside a set of polygons and leaves the rest of the surface unaltered. It is extremely useful for cleaning isolated problem areas in grids or cleaning the suture line related to merging two grids together. Its advantage over interactive smoothing is that the polygons provide documentation of where the smoothing was done and ensure that the smoothing is only done within those polygons and only done once. The steps used in this method are: 1. Use the Make/edit polygons process to create a set of polygons that encircle areas needing more aggressive smoothing than the rest of the grid. Figure: Polygons within which smoothing is to be done. 2. Display the surface and the constraint polygons in a 3D or 2D Window. 3. Go to the Smooth Operation dialog, hold your cursor over the set filter icon in the lower left corner and click on the line Set or change the filter in the box that appears. 4. When the Project Settings dialog appears, go to the Misc settings 2 tab and insert the Polygon by highlighting the polygon name and clicking the blue arrow under Global surface filter. Be sure to click on 4
5 the Apply inside or Apply outside radio button to tell the program where to smooth. Click OK to apply the parameters and dismiss the dialog. Figure: Operation showing the Set or change the filter option (left) and the Project dialog that appears when the line is clicked, showing the polygon inserted and the Apply the surfaces inside button pushed (right). 5. Click on the set filter icon so that it turns orange ( ). This will make the operation use the inserted polygons as constraints when it executes. 6. Set the parameters for the smoothing operation. 7. Click the Run button to perform the operation. Figure: Original grid with polygons circling areas ready for filtering (left), grid filtered only inside the polygons (right). 5
6 Interactive Smoothing Interactive smoothing is commonly used to clean small isolated problems in a grid. It is not normally used to smooth large areas of a grid, as that is more efficiently and accurately done with Operation Smoothing or Polygon Constrained Operation Smoothing. Interactive Smoothing is done in the Make/edit surface process. Making this process active makes the 2D Grid editing icons appear on the right side of the display area. Two icons are used to smooth, the Smooth area icon and the Peak remover icon. Of the two, the authors have found the Peak remover to be most useful. The steps used to make either of the methods work are the same: 1. Display the surface to be smoothed in a 3D Window. 2. Click on either the Smooth area or Peak remover icon. 3. Click on the Use the influence radius icon. 4. Set influence radius to adjust the size of the area to be smoothed. This is in terms of grid increments. 5. Smooth the grid by either: - Clicking on the spot to be smoothed, or - Clicking and dragging the mouse over the area of the grid that is to be smoothed. Figure: Unsmoothed grid (left), smoothed grid after using the Peak remover (right). Remember you have full Undo functionality. 6
Petrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Digitizing and Gridding Contours in Petrel SCM trainers and consultants use Petrel s contour digitizing and contour gridding tools on most projects.
More informationPetrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Using the Make Simple Grid Process to Build Un faulted Frameworks Un faulted reservoirs are relatively rare but do occur and provide a wonderful break
More informationPetrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Merging Overlapping Files into One 2D Grid Often several files (grids or data) covering adjacent and overlapping areas must be combined into one 2D Grid.
More information3. Input Data Editing
3. Input Data Editing There are few editing steps that must be completed before a 3D geological model is created. The steps include: 1. Creating Reservoir Boundary 2. Creating 3D Surfaces 3. Editing the
More informationPetrel TIPS&TRICKS from SCM
E&P SOLUTIONS Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Petrel Studio Part 1 The Petrel Studio was new to Petrel 2011, was augmented with new features in Petrel 2012 and contains a variety of
More informationPetrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Well Path Design Part I This TIPS&TRICKS is the first of a three part series intended to aid the geoscientist working in Petrel and tasked with providing
More informationPetrel TIPS&TRICKS from SCM
E&P SOLUTIONS Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Cropped & Flattened Volumes in *Petrel Geophysicists who use D volumes often want to work on a smaller part of the volume or they want
More informationPetrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Petrel 2D Grid Algorithms and the Data Types they are Commonly Used With Specific algorithms in Petrel s Make/Edit Surfaces process are more appropriate
More informationPetrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Well Sections in Petrel 2010 Geologists who use Petrel to create and use Well Sections have noticed a significant change in this area between Petrel
More informationUsing Kingdom Suite for 3D Horizon/Fault Interpretation Parts 3 & 4 - Horizon Interpretation and Correlation
Using Kingdom Suite for 3D Horizon/Fault Interpretation Parts 3 & 4 - Horizon Interpretation and Correlation Wilson (2010) 1 A footnote to last week's exercise Double Vision? - Last week when you were
More informationPetrel TIPS&TRICKS from SCM
Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Well Path Design Part II This TIPS&TRICKS is the second of a three part series intended to aid the geoscientist working in Petrel and tasked with providing
More informationSolidWorks 2½D Parts
SolidWorks 2½D Parts IDeATe Laser Micro Part 1b Dave Touretzky and Susan Finger 1. Create a new part In this lab, you ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select
More informationSolidWorks Intro Part 1b
SolidWorks Intro Part 1b Dave Touretzky and Susan Finger 1. Create a new part We ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select File New Templates IPSpart If the SolidWorks
More informationA cell is highlighted when a thick black border appears around it. Use TAB to move to the next cell to the LEFT. Use SHIFT-TAB to move to the RIGHT.
Instructional Center for Educational Technologies EXCEL 2010 BASICS Things to Know Before You Start The cursor in Excel looks like a plus sign. When you click in a cell, the column and row headings will
More informationAutodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
More information7. Vertical Layering
7.1 Make Horizons 7. Vertical Layering The vertical layering process consists of 4 steps: 1. Make Horizons: Insert the input surfaces into the 3D Grid. The inputs can be surfaces from seismic or well tops,
More informationStratigraphy Modeling Horizon Coverages
GMS TUTORIALS Stratigraphy Modeling Horizon Coverages This tutorial builds on the concepts taught in the tutorial entitled Stratigraphy Modeling Horizons and Solids. In that tutorial, you created solids
More informationLesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction.
3.1: Sculpting Sculpting in Fusion 360 allows for the intuitive freeform creation of organic solid bodies and surfaces by leveraging the T- Splines technology. In the Sculpt Workspace, you can rapidly
More informationFrontPage. Directions & Reference
FrontPage Directions & Reference August 2006 Table of Contents Page No. Open, Create, Save WebPages Open Webpage... 1 Create and Save a New Page... 1-2 Change the Background Color of Your Web Page...
More informationThis project covers the following design concepts:
Design Project 4 This project covers the following design concepts: DRAWING TOOLS SNAP TO GRID SETTING CONSTRAINTS CUT PATH TOOL CENTERLINE TEXT COPY & PASTE CONFORMING VECTOR CREATING A CLOSED REGION
More informationStepwise instructions for getting started
Multiparameter Numerical Medium for Seismic Modeling, Planning, Imaging & Interpretation Worldwide Tesseral Geo Modeling Tesseral 2D Tutorial Stepwise instructions for getting started Contents Useful information...1
More informationPolygon Modeling Basics Chapter 1 - Vertices
Polygon Modeling Basics Chapter 1 - Vertices In this tutorial we will cover the basic tools necessary for Polygon Modeling using the Vertex sub-object selection. It is less of a how to tutorial and more
More informationBeginning Tutorial the Lego
Beginning Tutorial the Lego In this tutorial, you will construct a simple hollowed-out block with a hole in it (looks like a Lego). You will learn the basics of creating and modifying sketches and features.
More informationTricking it Out: Tricks to personalize and customize your graphs.
Tricking it Out: Tricks to personalize and customize your graphs. Graphing templates may be used online without downloading them onto your own computer. However, if you would like to use the templates
More information2 Solutions Chapter 3. Chapter 3: Practice Example 1
1 Solutions This section includes the step by step solutions for the practice exercise for the following chapters and sections: Chapter 3 Chapter 4 Chapter 5 Chapter 11: Rainbow Springs sample test Final
More informationThis guide will help you with many of the basics of operation for your Epson 485wi BrightLink Projector with interactive functionality.
This guide will help you with many of the basics of operation for your Epson 485wi BrightLink Projector with interactive functionality. If you need further assistance with questions, you can refer to the
More informationModule 1: Basics of Solids Modeling with SolidWorks
Module 1: Basics of Solids Modeling with SolidWorks Introduction SolidWorks is the state of the art in computer-aided design (CAD). SolidWorks represents an object in a virtual environment just as it exists
More informationcreating files and saving for web
creating files and saving for web the template files assume a default image size of 300 x 300 pixels images intended for the web should be produced in rgb mode name your images in a logical format, so
More informationTutorial 01 Quick Start Tutorial
Tutorial 01 Quick Start Tutorial Homogeneous single material slope No water pressure (dry) Circular slip surface search (Grid Search) Intro to multi scenario modeling Introduction Model This quick start
More informationApplication Tutorial
Application Tutorial Use these instructions to assist in completing a downloaded application using Adobe Acrobat Reader. Adobe Acrobat Reader is a free download and may be downloaded at http://www.adobe.com.
More informationCandy is Dandy Project (Project #12)
Candy is Dandy Project (Project #12) You have been hired to conduct some market research about M&M's. First, you had your team purchase 4 large bags and the results are given for the contents of those
More informationWinSCP. Author A.Kishore/Sachin
WinSCP WinSCP is a freeware windows client for the SCP (secure copy protocol), a way to transfer files across the network using the ssh (secure shell) encrypted protocol. It replaces other FTP programs
More informationA Study of Angles & Curves
A Study of Angles & Curves Method 1: Cutting Quilt Shapes/Using the Shapes Tools Open BERNINA CutWork Software. Make sure that Create New is selected. Click Next. Place a dot in front of New Graphic. Select
More informationAncient Cell Phone Tracing an Object and Drawing with Layers
Ancient Cell Phone Tracing an Object and Drawing with Layers 1) Open Corel Draw. Create a blank 8.5 x 11 Document. 2) Go to the Import option and browse to the Graphics 1 > Lessons folder 3) Find the Cell
More informationThe scan tools are used to convert and edit bitmap images so that they can be cut or routed by the Torchmate.
Scan Tools The scan tools are used to convert and edit bitmap images so that they can be cut or routed by the Torchmate. Upon clicking the Scan tool, the flyout opens exposing the two scanning options.
More informationTechnique or Feature Where Introduced
Part 6: Keypad 4 Mirrored features Patterned features First extrusion Rounded corners In the earpiece part, you defined a radial pattern, one that created new instances of a feature at intervals around
More informationTRAINING GUIDE SOLIDS-LESSON-3
TRAINING GUIDE SOLIDS-LESSON-3 Mastercam Training Guide Objectives You will generate the solid model from the existing 2-dimensional geometry. This Lesson covers the following topics: Open an existing
More informationGraffiti Wallpaper Photoshop Tutorial
Graffiti Wallpaper Photoshop Tutorial Adapted from http://photoshoptutorials.ws/photoshop-tutorials/drawing/create-your-own-graffiti-wallpaper-inphotoshop.html Step 1 - Create a New Document Choose File
More information3 Polygonal Modeling. Getting Started with Maya 103
3 Polygonal Modeling In Maya, modeling refers to the process of creating virtual 3D surfaces for the characters and objects in the Maya scene. Surfaces play an important role in the overall Maya workflow
More informationFrontCounter BC Discovery Tool Instructions. NOTE: You must have Google Earth installed to use this tool.
NOTE: You must have Google Earth installed to use this tool. These instructions are written for use with a Microsoft Windows Work Station. This tutorial will step you through navigating to and viewing
More informationGMS 10.3 Tutorial Stratigraphy Modeling Horizon Coverages Use horizon coverages to help control the Horizons Solids operation
v. 10.3 GMS 10.3 Tutorial Stratigraphy Modeling Horizon Coverages Use horizon coverages to help control the Horizons Solids operation Objectives Learn how to constrain the areal extent of the solids created
More informationUser Manual Version 1.1 January 2015
User Manual Version 1.1 January 2015 - 2 / 112 - V1.1 Variegator... 7 Variegator Features... 7 1. Variable elements... 7 2. Static elements... 7 3. Element Manipulation... 7 4. Document Formats... 7 5.
More informationA Guide to Autodesk Maya 2015
A Guide to Autodesk Maya 2015 Written by Mitchell Youngerman Table of Contents Layout of Toolbars...pg 1 Creating Objects...pg 2 Selecting & Deselecting Objects...pg 3 Changing Perspective... pg 4 Transforming
More information4) Study the section of a worksheet in the image below. What is the cell address of the cell containing the word "Qtr3"?
Choose The Correct Answer: 1) Study the highlighted cells in the image below and identify which of the following represents the correct cell address for these cells: a) The cell reference for the selected
More informationData Grid Utilities - Searching Data Grids
Data Grid Utilities - Searching Data Grids Step 1 : To search any column on selected data grids begin by right mouse-clicking the column header for the column you want to search. This feature works on
More informationBackground on Kingdom Suite for the Imperial Barrel Competition 3D Horizon/Fault Interpretation Parts 1 & 2 - Fault Interpretation and Correlation
Background on Kingdom Suite for the Imperial Barrel Competition 3D Horizon/Fault Interpretation Parts 1 & 2 - Fault Interpretation and Correlation Wilson (2010) 1 Fault/Horizon Interpretation Using Seismic
More informationWorking with PDF s. To open a recent file on the Start screen, double click on the file name.
Working with PDF s Acrobat DC Start Screen (Home Tab) When Acrobat opens, the Acrobat Start screen (Home Tab) populates displaying a list of recently opened files. The search feature on the top of the
More informationWeek 5 Creating a Calendar. About Tables. Making a Calendar From a Table Template. Week 5 Word 2010
Week 5 Creating a Calendar About Tables Tables are a good way to organize information. They can consist of only a few cells, or many cells that cover several pages. You can arrange boxes or cells vertically
More informationComputer learning Center at Ewing. Course Notes - Using Picasa
1st January 2014 Computer learning Center at Ewing Course Notes - Using Picasa These course notes describe the content of the Using Picasa course. The course notes are based on Picasa 3. This course material
More informationAUTODESK FUSION 360 Designing a RC Car Body
AUTODESK FUSION 360 Designing a RC Car Body Abstract This project explores how to use the sculpting tools available in Autodesk Fusion 360 Ultimate to design the body of a RC car. John Helfen john.helfen@autodesk.com
More informationColony Counting User Manual A D I V I S I O N O F S Y N O P T I C S L T D
ProtoCOL Colony Counting User Manual S Y N B I O S I S A D I V I S I O N O F S Y N O P T I C S L T D All possible care has been taken in the preparation of this publication, but Synoptics Limited accepts
More informationMS Word Basics. Groups within Tabs
MS Word Basics Instructor: Bev Alderman L e t s G e t S t a r t e d! Open and close MS Word Open Word from the desktop of your computer by Clicking on the Start>All programs>microsoft Office >Word 2010
More informationSCENE FILE MANIPULATION SCENE FILE MANIPULATION GETTING STARTED MODELING ANIMATION MATERIALS + MAPPING RENDERING. Saving Files. Save.
SCENE FILE MANIPULATION SCENE FILE MANIPULATION There are several things you can do with a scene file in 3ds Max. You can save a file, save a file temporarily and retrieve it, and combine scene files.
More informationFINANCIAL SOFTWARE CONVERSION INSTRUCTIONS
FINANCIAL SOFTWARE CONVERSION INSTRUCTIONS Member FDIC. 2018 United Community Bank ucbi.com/fouroaks 1 TABLE OF CONTENTS FINANCIAL SOFTWARE CONVERSION INSTRUCTIONS QuickBooks for Mac - Web Connect 3 QuickBooks
More informationIntroduction to Microsoft Word 2007 Quickguide
Introduction to Microsoft Word 2007 Quickguide Opening Word -Click the Start button -Click Programs from the start menu -Select Microsoft Office -Click Microsoft Office Word 2007 -A new blank document
More informationWindows Movie Maker lets you edit videos from video and photo files. It is free from Microsoft.
Getting Started with Windows Movie Maker Windows Movie Maker lets you edit videos from video and photo files. It is free from Microsoft. Start a project To start, you will need to import photos or video
More informationUCL Depthmap 7: Convex Space Analysis
UCL Depthmap 7: Convex Space Analysis Version 7.12.00c Outline This tutorial will cover drawing a convex map, linking the spaces, and then analysing it. New file First, begin a New file, either from the
More informationDevelopment Authority of the North Country (DANC) Internet Mapping Application Instructions Public Viewer 1. Purpose. 2. Logging-in. 3.
Development Authority of the North Country (DANC) Internet Mapping Application Instructions Public Viewer 1. Purpose The purpose of this document is to outline basic functionality of the DANC Internet
More informationOpen Excel by following the directions listed below: Click on Start, select Programs, and the click on Microsoft Excel.
Candy is Dandy Grading Rubric You have been hired to conduct some market research about M&M's. First, you had your team purchase 4 large bags and the results are given for the contents of those bags. You
More informationCreate a unit using United Streaming and PowerPoint. Materials: Microsoft PowerPoint, Internet access, United Streaming account
Create a unit using United Streaming and PowerPoint Materials: Microsoft PowerPoint, Internet access, United Streaming account Find United Streaming Clips: 1. Decide on a topic for your unit. 2. Search
More informationAlibre Design Tutorial - Simple Revolve Translucent Glass Lamp Globe
Alibre Design Tutorial - Simple Revolve Translucent Glass Lamp Globe Part Tutorial Exercise 2: Globe-1 In this Exercise, We will set System Parameters first. Then, in sketch mode, we will first Outline
More informationEditing Polygons. Adding material/volume: Extrude. Learning objectives
Learning objectives Be able to: use the Extrude tool to add volume to a polygon know what edge loops are and how to insert edge loops in a polygon cut edges in a polygon know multiple methods of sewing
More informationDOING MORE WITH POWERPOINT: MICROSOFT OFFICE 2013
DOING MORE WITH POWERPOINT: MICROSOFT OFFICE 2013 GETTING STARTED PAGE 02 Prerequisites What You Will Learn USING MICROSOFT POWERPOINT PAGE 03 Slide Views MORE TASKS IN MICROSOFT POWERPOINT PAGE 05 Formatting
More informationOptimizing ImmuNet. In this chapter: Optimizing Browser Performance Running Reports with Adobe Acrobat Reader Efficient Screen Navigation
Optimizing ImmuNet In this chapter: Optimizing Browser Performance Running Reports with Adobe Acrobat Reader Efficient Screen Navigation Optimizing Browser Performance Unless instructed to do otherwise,
More informationSeaSonde Configure Combine Processing
SeaSonde Configure Combine Processing 144.01.1708.UG Aug 14, 2017 SeaSonde Configure Combine Processing SeaSondeCombineOptions configures how the transferred Radials and Ellipticals sources are combined
More informationExcel 2013 Charts and Graphs
Excel 2013 Charts and Graphs Copyright 2016 Faculty and Staff Training, West Chester University. A member of the Pennsylvania State System of Higher Education. No portion of this document may be reproduced
More informationUsing the Link to Petrel
Using the Link to Petrel Prerequisites: * Petrel installed (Current supported versions are 2014, 2015 and 2016) * GeoTeric installed * Valid GeoTeric license The Link for Petrel connects automatically
More informationUsing OPUS to Process Evolved Gas Data (8/12/15 edits highlighted)
Using OPUS to Process Evolved Gas Data (8/12/15 edits highlighted) Once FTIR data has been acquired for the gases evolved during your DSC/TGA run, you will process using the OPUS software package. Select
More informationAuthor A.Kishore/Sachin WinSCP
WinSCP WinSCP is a freeware windows client for the SCP (secure copy protocol), a way to transfer files across the network using the ssh (secure shell) encrypted protocol. It replaces other FTP programs
More information1) Merge the cells that contain the title and center the title
Supplies: You will need a storage location to save your spreadsheet for use in Session 2. You will need the 2 handouts pertaining to Session 1 Instructions: Follow the directions below to create a budget
More informationL E S S O N 2 Background
Flight, Naperville Central High School, Naperville, Ill. No hard hat needed in the InDesign work area Once you learn the concepts of good page design, and you learn how to use InDesign, you are limited
More informationLab Practical - Limit Equilibrium Analysis of Engineered Slopes
Lab Practical - Limit Equilibrium Analysis of Engineered Slopes Part 1: Planar Analysis A Deterministic Analysis This exercise will demonstrate the basics of a deterministic limit equilibrium planar analysis
More informationCreating 3D Text with LibreOffice
Creating 3D Text You probably have seen examples of 3D text and perhaps wondered how it can be done. As with most computer graphics, there are a lot of programs that can do 3D modeling. However, there
More informationWORD 2010 TIP SHEET GLOSSARY
GLOSSARY Clipart this term refers to art that is actually a part of the Word package. Clipart does not usually refer to photographs. It is thematic graphic content that is used to spice up Word documents
More informationReference Services Division Presents. Microsoft Word 2
Reference Services Division Presents Microsoft Word 2 This handout covers the latest Microsoft Word 2010. This handout includes instructions for the tasks we will be covering in class. Basic Tasks Review
More informationNVTI s POWERPOINT 101
NVTI s POWERPOINT 101 1) Click on START on bottom left of screen 2) Go to PROGRAMS 3) Go to MICROSOFT POWERPOINT, click. 4) When it opens, it s on Blank Presentation Hit OK 5) Choose a Layout (click on
More informationCreate a Seating Chart Layout in PowerTeacher
Nova Scotia Public Education System Create a Seating Chart Layout in PowerTeacher Revision Date: 1 Seating Chart Overview...3 2 How to Create a Seating Chart Layout...4 3 How to Create Additional Layouts
More information12. Defining Fluid Contacts
12. Defining Fluid Contacts 12.1 Creating a New Contact Set After having built a Petrel 3D grid and prior to running the volume calculation, the various contacts should be defined in the Make Contacts
More informationAdobe Illustrator. Always NAME your project file. It should be specific to you and the project you are working on.
Adobe Illustrator This packet will serve as a basic introduction to Adobe Illustrator and some of the tools it has to offer. It is recommended that anyone looking to become more familiar with the program
More informationDocument Editor Basics
Document Editor Basics When you use the Document Editor option, either from ZP Toolbox or from the Output option drop-down box, you will be taken to the Report Designer Screen. While in this window, you
More informationGrade: 7 Lesson name: Creating a School News Letter Microsoft Word 2007
Grade: 7 Lesson name: Creating a School News Letter Microsoft Word 2007 1. Open Microsoft Word 2007. Word will start up as a blank document. 2. Change the margins by clicking the Page Layout tab and clicking
More informationDigitizing and Editing Polygons in the STS Gypsy Moth Project. M. Dodd 2/10/04
Digitizing and Editing Polygons in the STS Gypsy Moth Project M. Dodd 2/10/04 Digitizing and Editing Polygons in the STS Gypsy Moth Project OVERVIEW OF DIGITIZING IN STS 3 THE DIGITIZING WINDOW 4 DIGITIZING
More informationGetting Familiar with Microsoft Word 2010 for Windows
Lesson 1: Getting Familiar with Microsoft Word 2010 for Windows Microsoft Word is a word processing software package. You can use it to type letters, reports, and other documents. This tutorial teaches
More informationPart 2 Add Frame, Arrow, Painted Text.
Part 2 Add Frame, Arrow, Painted Text. You can use the same Picture on PicPick, or add a new one as I showed you in Step 2 - Part 1. As I mentioned before in Step 2 - Part 1, if you don't have PicPick,
More informationHow to use the Sales Based Availability Dashboard
How to use the Sales Based Availability Dashboard Supplier Guide Sept 2017 v1 1 Contents What is Sales Based Availability and why is it important?... 3 How is Sales Based Availability calculated and how
More informationUsing Word 2011 at Kennesaw State University
Using Word 2011 at Kennesaw State University Getting Started Information Technology Services Outreach and Distance Learning Technologies Copyright 2011 - Information Technology Services Kennesaw State
More informationCompare and Merge Track Changes
Compare and Merge Track Changes Course Description The document you have been working on for a couple of weeks is finally finished. Before sending the document to its final destination to be published,
More informationADOBE PREMIERE PRO Lesson: The Basics
ADOBE PREMIERE PRO Lesson: The Basics 1. Insert your flash drive and make sure it shows up on the Desktop 2. Click on the Premiere icon 3. Click on Create New Project 4. Name your project LEARNING_yourlastname
More informationIntroduction to Microsoft Publisher
Introduction to Microsoft Publisher Day One Agenda: Introduction Templates Layout Inserting and Formatting Text Inserting and Formatting Pictures Practice, Questions Day Two Agenda: Review Day One Tables
More informationMAKING TABLES WITH WORD BASIC INSTRUCTIONS. Setting the Page Orientation. Inserting the Basic Table. Daily Schedule
MAKING TABLES WITH WORD BASIC INSTRUCTIONS Setting the Page Orientation Once in word, decide if you want your paper to print vertically (the normal way, called portrait) or horizontally (called landscape)
More information1. Move your mouse to the location you wish text to appear in the document. 2. Click the mouse. The insertion point appears.
Word 2010 Text Basics Introduction Page 1 It is important to know how to perform basic tasks with text when working in a word processing application. In this lesson you will learn the basics of working
More informationLet s Make a Front Panel using FrontCAD
Let s Make a Front Panel using FrontCAD By Jim Patchell FrontCad is meant to be a simple, easy to use CAD program for creating front panel designs and artwork. It is a free, open source program, with the
More informationBeginner s Guide to Microsoft Excel 2002
Beginner s Guide to Microsoft Excel 2002 Microsoft Excel lets you create spreadsheets, which allow you to make budgets, track inventories, calculate profits, and design charts and graphs. 1. Open Start
More informationMicrosoft Word 2011 Tutorial
Microsoft Word 2011 Tutorial GETTING STARTED Microsoft Word is one of the most popular word processing programs supported by both Mac and PC platforms. Microsoft Word can be used to create documents, brochures,
More informationUnderstanding the Interface
2. Understanding the Interface Adobe Photoshop CS2 for the Web H O T 2 Understanding the Interface The Welcome Screen Interface Overview Customizing Palette Locations Saving Custom Palette Locations Customizing
More informationOrgPublisher Advanced Box Layout Editor
OrgPublisher Advanced Box Layout Editor OrgPublisher Table of Contents Table of Contents... 3 Using the... 3 Arranging Chart Box Sections... 3 Sizing the Chart Box Section... 4 Moving, Deleting, or Resizing
More informationPayment Function Exercise
Payment Function Exercise Follow the directions below to create a payment function exercise. Read through each individual direction before performing it, like you are following recipe instructions. Remember
More informationWebmail: Basics. Folders:
Webmail: Basics To use webmail: Webmail can be accessed from any computer that has an internet connection. Type webmail.osceola.k12.wi.us in the address bar. (Note that there is no www preceding this URL:
More informationOracle General Navigation Overview
Oracle 11.5.9 General Navigation Overview 1 Logging On to Oracle Applications You may access Oracle, by logging onto the ATC Applications Login System Status page located at www.atc.caltech.edu/support/index.php
More informationEDITING SHAPES. Lesson overview
3 CREATING AND EDITING SHAPES Lesson overview In this lesson, you ll learn how to do the following: Create a document with multiple artboards. Use tools and commands to create basic shapes. Work with drawing
More information