BCM50 Rls. 3.0, BCM200/400 Rls. 4.0 & BCM450 Rls. 1.0 Installation, Configuration & Maintenance

Transcription

1 1 Nortel BCM50 Rls. 3.0, BCM200/400 Rls. 4.0 & BCM450 Rls. 1.0 Installation, Configuration & Maintenance Question: 1 You have installed a DSM32+ MBM in slot 1 of a new BCM450 main unit and you want to connect a set and perform set-based programming. What is the next step? A. Identify the module. B. Deconfigure the module. C. Configure the module. D. Connect a set to the DSM32+. Question: 2 While configuring a DTM module on a BCM450, the module was mistakenly identified as a DTMPRI instead of a DTM-T1. What must you do to correct the module identification? A. Select the row of the DTM you configured. Click the Configure button and enter TM-T1?as the module type. B.Select the row of the DTM you configured. Click the Deconfigure button. Click OK. Double-click the?onfigured Device?column and select?tm-t1?as the module type. C.Select the row of the DTM you configured. Double-click the?onfigured Device?column and select?d.select the row of the DTM you configured. Click the Disable button. Click OK. A. Select the row of the DTM you configured. Click the Configure button and enter DTM-T1 as the module type. B. Select the row of the DTM you configured. Click the Deconfigure button. Click OK. Doubleclick the Configured Device column and select DTM-T1 as the module type.

2 2 C. Select the row of the DTM you configured. Double-click the onfigured Device column and select DTM-T1 as the module type. D. Select the row of the DTM you configured. Click the Disable button. Click OK. Double-click the Configured Device column and select DTM-T1 as the module type. Question: 3 Which Media Bay Module (MBM) can be combined with the G4x16 on the same DS30 bus on a BCM200/400 system? A. DTM B. GATM4 C. GASM8 D. BRI S/T Question: 4 You need to renumber a group of DNs. You also want to move the voice mailboxes with the renumbered DNs. Which BCM system allows you to do this? A. BCM50 Rls. 2.0 B. BCM50 Rls. 3.0 C. BCM400 Rls. 4.0 D. BCM450 Rls. 1.0 Question: 5 Click the Exhibit button. You are configuring IP trunks on a new BCM450 that does not have a Capacity Expansion Card (CEC). The authorization license allows you to have 32 VoIP trunks. For the company planned future growth, 40 IP trunks on the system are set in the configuration so the total number of lines input as 40, and then OK clicked. What will happen next?

3 3 A. The system will configure the IP trunks with a low line number of 001 and a high line number of 32. B. The system will configure the IP trunks with a low line number of 001 and a high line number of 40. C. An error message is displayed since a BCM450 without a CEC can only support eight VoIP trunks. D. An error message is displayed indicating your license is not sufficient to configure 40 VoIP trunks. Question: 6 You want to install a Digital Trunk Module (DTM) in the BCM450 main unit. How must you set the DIP switches on the DTM? A. Set all of the DIP switches to OFF. B. Set all of the DIP switches to ON. C. Set the first DIP switch to ON and set the rest to OFF. D. Set the first DIP switch to OFF and set the rest to ON. Question: 7 You are creating a set template based on a DN. You clicked the Add button on the Set Templates screen. What must the value in the Source Template field be? A. DN B. DID C. PBX D. None Question: 8

4 4 You are configuring a GATM4 on a BCM450. What is the start line number the system will suggest? A. 001 B. 002 C. 011 D. 021 E. 061 Question: 9 Which statement about the BCM450 capacity expansion card (CEC) is true? A. A BCM450 with a CEC can support a maximum of 300 trunks. B. You can remove the CEC if the customer capacity needs drop. C. A BCM450 with a CEC can support a maximum of 130 stations. D. The CEC is a standard card that comes installed with every BCM450. Question: 10 What is the maximum number of IP trunks you can have on a BCM450 with a capacity expansion card? A. 48 B. 80 C. 130 D. 300 Answer(s): C Question: 11 What is the function of the BCM450 chassis interface board (CIB)? A. The CIB connects the base function tray to the chassis wiring. B. The CIB increases IP trunk capacity. C. The CIB connects the media services card to the media bay modules. D. The CIB in the BCM450 can be used in a BCM400 main unit. Answer(s): A Question: 12 You want to configure an expansion unit Media Bay Module (MBM) on a BCM450. You highlighted the expansion 1 row on the Telephony Resources screen. What is your next step?

5 5 A. Click the Deconfigure button and click OK. B. Click the Configure button and modify the values. C. Double-click the Configured Device field and select MBM-6. D. Double-click the Configured Device field and select the type of MBM you want to install. Answer(s): C Question: 13 On the BCM monitor, what does the UIP tab provide? A. It provides RTP session information. B. It indicates only Contact Center usage. C. It provides master DSP resource usage. D. It provides detailed call information. Question: 14 You are upgrading a BCM200/400 Rls. 4.0 to BCM450 Rls Which statement is correct regarding the upgrade path? A. You cannot reuse the BCM400 media bay modules on a BCM450 system. B. You can replace the BCM400 base function tray (BFT) with a BCM450 BFT. C. The BCM450 intended to replace the BCM400 must have at least one keycode in the KRS database. D. You can migrate BCM450-supported keycoded features from a BCM200 Rls. 4.0 to a BCM450 Rls. 1.0 system. Question: 15 In a BCM deployment, a customer is monitoring the Contact Center status. Which BCM Monitor tab will allow them to perform this activity? A. UIP B. IP Devices