RM-2 and RM-2AC. Resource Module Converts Solid-State Outputs to Force-Guided Relay Outputs

Transcription

1 esource M- and Module M-ACM- C US C US File No. L9000- escription M- and M-AC esource Module Converts Solid-State s to Force-Guided elay s Converts the solid-state safety and auxiliary outputs of one STI safety device to electromechanical force-guided safety relay outputs Compatible with STI s MS00, OF00-0, and PA00 products CE approved The M- and M-AC are resource modules in a IN configuration that provides power for safety devices with solid state outputs and converts the outputs of those devices to force-guided relay outputs. Two NO safety relay outputs and two NC auxiliary relay outputs are provided. These force-guided safety relays can be used as the machine primary control element () depending on the load rating of the device being switched by the relay contacts. Please refer to the specifications section for output switching capabilities. Additionally, the M- amd M-AC serves as a central point for terminating all signals to and from a solid-state safety device including monitoring. emovable terminal blocks facilitate installation and servicing. Available for C or AC input power Provides connection points for all safety device functions including monitoring and VC power 00 and 0 mm (AC) IN enclosures emovable terminal blocks A Go to the Engineering Guide For in-depth information on safety standards and use. 0

2 esource M- Module and M-AC Specifications Performance esponse Time: 0 ms NO, 0 ms NC Indicators: green LEs: power, safety output, safety output Electrical Input Power: M- VC, 9 VA; M-AC 00 to 0 VAC, 0 VA Safety s: M- Two NO force-guided contacts rated 0 VAC, A; M-AC One NO and one NO/NC force-guided contacts rated 0 VAC, A (Non-Safety) s: M- Two NC rated 0 VAC A; M-AC One NO/NC rated 0 VAC A Monitor or EM: The safety output of the M unit may be monitored by the light curtain Cable Connections/ Terminal Blocks: rows of removable terminal blocks, AWG max. wire Environmental Enclosure ating: IP0 Operating Temperature: 0 to C ( to F) elative Humidity: 9% maximum, non-condensing Conformity/ Approvals Conformity to Standards: CE approved and conforms to IEC 9-, IEC 08, EN 9-, EN 00-, EN 08, and Type * safety category. UL listed. Mechanical Enclosure: Polycarbonate Mounting: mm (.8 in.) IN rail or screw imensions: M-: 00 mm W x mm H x 0 mm (.9 in. W x.9 in. H x. in. ) M-AC: 0 mm W x mm H x 0 mm (.9 in. W x.9 in. H x. in. ) * When used with an STI Type safety light curtain. Specifications are subject to change without notice. 0

3 esource M- and Module M-ACM- Wiring Connecting a 00 Series Safety Light Curtain Via an M- Module The STI M- module provides force-guided relay outputs for machine control as well as a convenient location to terminate all outputs and inputs from the MS eceiver ed Cable OANGE O GEEN OSS OSS Aux. start 0VC YELLOW PINK VIOLET O BLUE GAY BOWN OSS OSS Monitor Sig Aux. +vdc 0VC Earth Ground Power Supply M- 0 VC 0VC +VC +VC CONTOL VOLTAGE SUPPESSO SUPPESSO +VC WHITE +VC +V ef. shield +VC AIN ed cable AIN WHITE +VC Control Interface Aux. in eturn In ed Cable STAT 0VC BOWN 0VC eturn 00 Transmitter monitoring must be used when using the M. For transmitter with option If the M is the Final Switching evice connect the Blue Pink wire to the MONITO terminal of the M. If force-guided control relays are used as Final Switching evices connect the Pink wire to the Black Sig. terminal. Then connect a set of N.C. contacts from and to the in and return terminals. (o not connect both.) For testing prior to installation, the user may select OFF (default factory setting). In this case the line (pink wire) must be connected to the system 0 VC line. User-supplied over current protection, A max. Auxilary output-connect to PLC (optional). User-supplied fuse. If remote start is not used, install a jumper across the connections at the Control Interface terminals. Verify that the final switching devices are properly suppressed. A Go to the Engineering Guide For in-depth information on safety standards and use. 08

4 esource M- Module and M-AC Connecting a MS/PA00 Via an M-AC Module Wiring Procedure MS/PA00 CV CV color code Table Signal MS PA Braid Green 0 VC Brown Brown +VC White White OSS A Orange or Green ed OSS B Yellow Yellow Violet or Blue Blue Grey Grey Pink Pink Control voltage 0 VC +VC OSS A OSS B Verify that the final switching devices are properly suppressed. monitoring must be used when using the M-AC. If the M-AC is the final switching device connect the pink wire to the Mon terminal # 8. If external forceguided relays are the final switching device, they must be monitored, connect the pink wire to In and connect a set of N/C contacts from force-guided relays to Out terminal # 0 and eturn terminal #. (do not connect both). The start input requires a N/C.switch contact, install a jumper when not in use. The input requires a N/C contact, install a jumper when not in use. The output is shown connected to a lamp, NPN configuration shown. When the AUX is a PNP, connect the other side of the load to terminal 9 (0VC). No connections on Terminal to and Termianl to 8 are needed when using STI light curtains. 0 VC +VC OSS A OSS B Aux. In In 8 Mon 9 In 0 Out eturn Sel In Sel In In In OS00 not used MS/PA00 OS00 Inputs OS00 / Inputs M-AC SW SW AC Voltage Input F T.A / 0V MS/PA00 XMT Input OS00 Select Out Line Voltage Neutral + VC 0 VC 0 9 eturn 8 Sel out Sel out eturn out eturn out Earth 00-0 VAC XMT color code Table Signal MS PA + VC White White Brown Brown 0 VC Braid Green Blue Blue ret. Black Black + VC 0 VC eturn MS/PA00 XMT AC SUPPESSO AC SUPPESSO Safety s Controls Interface eturn output 0 +VC fused 9 0 VC fused 8 Aux pass thru Lamp 09

5 esource M- and Module M-ACM- Wiring (continued) Connecting the Opto OS00 Via an M-AC Module 0 VC +VC OSS A OSS B EM() Select Select return Aux. Braid Yellow ed Blue Grey Pink E E Orange/White Verify that the final switching devices are properly suppressed. E () monitoring must be used when using the M-AC. If the M-AC is the final switching device connect the green wire to the EM () MON terminal # 8. If external force-guided relays are the final switching device they must be monitored, connect the green wire to EM () In and connect a set of N/C contacts from force-guided relays to EM () Out terminal # 0 and eturn terminal #. (do not connect both). Control voltage The zone select inputs are used to alternate between zones. No connections are needed when the OS00 is configured to a single AC SUPPESSO zone. The start input requires a N/C switch contact, E install a jumper when not in use. The output is shown connected to a lamp, NPN configuration shown. When the AC SUPPESSO AUX output is a PNP, connect the other side of the load to terminal 9 (0VC). E No connections needed when using the OS00. output configuration switches. Brown White Pink Orange/Black Black ed/black 0 VC +VC OSS A OSS B Aux. In In 8 mon 9 In 0 Out eturn Sel In Sel In In In MS/PA00 OS00 Inputs OS00 / Inputs elay Pass-thru NPN PNP Safety s M-AC SW SW AC Voltage Input MS/PA00 XMT Input OS00 Select Out Controls Interface Line Voltage Neutral F T.A / 0V Not Used + VC 0 VC 0 9 eturn 8 Sel Out Sel Out eturn Out eturn Out eturn 0 +VC Fused 9 0 VC Fused 8 Aux Pass Thru Earth 00-0 VAC Signal Lamp A Go to the Engineering Guide For in-depth information on safety standards and use. 0

6 Transmitter Scientific Technologies Inc. Fremont CA, USA Tel: 0/08-00, Fax 0/- Controls Interface AUX Power Supply VC 9 VA eceiver 0 VAC A 00 VA Max esource M- Module and M-AC imensions mm/in. M- M-AC.9. OSS OSS MONITO or SIG AUX STAT V+ V+ V- V- V+ V- ET POWE M- ET AUX +V EF s UN TOP VIEW TOP VIEW BOTTOM VIEW 8..8 SLOT. X.L 0.8 X 0.L BACK VIEW FONT VIEW BACK VIEW FONT VIEW T SIE VIEW..0 T SIE VIEW.0.9 Ordering The M- is a resource module option for the MS00, OF00-0 and PA00 with a VC input. The M-AC may be used with the MS00, OF00-0 and PA00. It operates on 00 to 0 VAC input voltage and provides VC operating voltage to the light curtain. In addition, the M-AC provides a centralized location for wire termination. Model No. M- M-AC escription esource module, VC, IN rail-mount, MS00, OF00-0, PA00 esource module, 00 to 0 VAC, IN rail-mount, MS00, OF00-0, PA00 and OS00. For information on the MiniSafe MS00, see page 0 For information on the OptoFence OF00-0, see page 8 For information on the Perimeter Access Guarding evice PA00, see page C For information on the Opto OS00, see page B For information on STI safety light curtain accessories, see page 8