Shown here with optional quick-disconnect cable kit.

Transcription

1 US File No. LR9000 Description BeamSafe 0 m (00 ft.) range Four possible transmit codes eliminate crosstalk from multiple units in the same area II Long-Range, Single-Beam Safety ontrol Signal strength indicator and integral Gun Sight allow easy installation No interconnecting cables required, which speeds long-range installations Three models available: Relay output with 4 VD power input Relay output with 8 to 0 V power input Solid-state output with 4 VD power input Switch-selected utomatic Start or Start/Restart Interlock operation Lens heater Shown here with optional quick-disconnect cable kit. The BeamSafe II is a long-range single-beam safety control designed for perimeter and access guarding. Diverse redundant microprocessor design provides safe, control reliable operation. BeamSafe II system consists of one transmitter and one receiver. No interconnecting cables or separate control enclosure are required. Mounted on the receiver, four separate visible indicators provide instant information on system clear, blocked or interlocked status as well as signal strength. dditional diagnostic indicators on the receiver provide codes to assist with troubleshooting. Output options include redundant solid-state or force-guided relays located in the receiver. Immunity to weld flash and ambient light are enhanced by coding the infrared beam. This feature also eliminates interference from other BeamSafe II units installed in close proximity. tight beam angle reduces problems associated with reflective surfaces. The Beamsafe II s built-in lens heater is effective in environments where condensation may form on the transmitter or receiver lens. djustable mounting brackets allow easy alignment Designed in accordance with IE49, EN94- and NSI B.9-00 Go to the Engineering Guide For in-depth information on safety standards and use. 4 US Tel. /888/0-47 anada Tel. /8/98-7

2 pplications Perimeter Guarding Shown here with one transmitter and receiver. Mirrors are used to form two beams and also turn corners. transmitter receiver floor to 9 ft 0. to 8 m in 400 mm in 900 mm Long-Range Perimeter Guarding Two transmitter/receiver pairs using two mirrors and Omron STI mounting stands to direct the beam around a corner. transmitter transmitter floor to 7 ft 0. to m in 400 mm in 900 mm receiver receiver Double Bounce This configuration guards access to hazardous work cells. One transmitter and receiver combined with two Omron STI 4 in. mirrors and mounting brackets. transmitter receiver floor to 7 ft 0. to in 400 mm in 900 mm 4 mirror 4 mirror Specifications Performance Protected Height: Single Beam Operating Range: 0. to 0 m ( to 00 ft.) Beam Diameter: mm (. in.) Maximum Response Time: <0.0 seconds for all models D Models Input Power: 4 V ±0% (negative ground) Receiver/Relay Output: 0.4 Max Receiver/SS Output: 0.80 Max Transmitter: 0.7 Max Models Input Power: 00 to 0 V ±0%, 0/0 Hz; Receiver V: V Receiver 0 V: V Transmitter V: 0. V Transmitter 0 V: 0 V Effective perture ngle:. maximum half angle Frequency Selection: 4 non-interfering codes, all models Diagnostics: Built-in diagnostic indicators Output: Relay Output Version: Two relays with force-guided contacts, NO rated 4 at V, 00 W switched power (.0 kv). D Loads are limited to 00 V maximum. Estimated mechanical life is 0,000,000 operations. Electrical life is typically,000,000 operations at 00 V. uxiliary Monitoring Relay: 400 V /D maximum, 0. ; total power 80 mw maximum. Solid-State Output Version: Two safety solid-state relay outputs. Each output sources (PNP) up to 0. at 4 VD. onstruction: Polyester powder-painted aluminum body. nodized aluminum end-caps. Operating Temperature: 0 to ( to F) Protection ategory: IP; NEM 4 gencies: Designed in accordance with IE 49, type 4 and UL/S requirements. Specifications are subject to change without notice. US Tel. /888/0-47 anada Tel. /8/98-7

3 R R R BeamSafe II Dimensions mm/in. BeamSafe II, Relay Output Version 0. c B ref. mounting holes (4) for lternte rer mounting front VieW mounting BrcKet SUrfce mtg "footprint" DimenSiOnS.9.0 r (X) BeamSafeII ref. SiDe VieW BeamSafe ii, relay Output Version Unit length Dims c receiver c transmitter Dc receiver B c lternte rer cble entry BeamSafeII Receiver f f BcK/rer VieW SlOtS for t-nuts (X) c.9.4 l 0.7 Di. Dc transmitter top VieW BOttOm VieW Dimensions: mm in ± 0. ± 0.0 DJUStBle mounting BrcKet BeamSafe II, Solid-State Output Version, Tranmitter and Receiver This drawing is available in D format at ref mounting holes (4) for lternte rer mounting BeamSafeII 8. ref. BeamSafeII Receiver lternte rer cble entry.4.00 front VieW SiDe VieW BcK/rer VieW mounting BrcKet SUrfce mtg "footprint" DimenSiOnS r (X) c l.0 0. (X) Ø top VieW SlOtS for t-nuts BOttOm VieW DJUStBle mounting BrcKet mm ± Dimensions: 0. Go into the ± 0.0 Engineering Guide For in-depth information on safety standards and use. US Tel. /888/0-47 anada Tel. /8/98-7

4 Wiring two normally Open contacts c Voltage connections BSrc J J7 earth/ground Output Output B uxiliary monitor relay (non Safety Output) (n.c.) Start to 0 Vc mpce mpce no external voltage is to be applied to terminals &. Damage to unit will occur. mpce mpce to machine control Stop circuit Wrning: rc suppression devices should only be installed across the coils of the machine control relays. never install rc Suppression devices directly across the control output contacts of the BeamSafe. n arc suppression device installed across the contacts may fail with a short circuit and will result in an unsafe condition. these relay contacts must be forceguided contacts. User supplied over current protection, 4 max. normally Open/normally closed connection Diagram BSrc 00 to 0 Vc mpce mpce earth/ground 7 8 to machine control Stop circuit J J7 Output Output B uxiliary monitor relay (non Safety Output) (n.c.) Start mpce mpce no external voltage is to be applied to terminals &, Damage to unit will occur. Wrning: rc suppression devices should only be installed across the coils of the machine control relays. never install rc Suppression devices directly across the control output contacts of the BeamSafe. n arc suppression device installed across the contacts may fail with a short circuit and will result in an unsafe condition. these relay contacts must be forceguided contacts. User supplied over current protection, 4 max. US Tel. /888/0-47 anada Tel. /8/98-7 7

5 Wiring (continued) two normally Open contacts Dc Voltage connections (Solid-State Output model) BSrc4 J Sourcing earth/ground Output Output B Start (n.c.) Signal return VDc two normally Open contacts 4 VDc Voltage connections mpce mpce no external voltage is to be applied to terminals 4 & ; Damage to unit will occur. mpce mpce to machine control Stop circuit Wrning: rc suppression devices should only be installed across the coils of the machine control relays. never install rc Suppression devices directly across the control output contacts of the BeamSafe. n arc suppression device installed accros the contacts may fail with a short circuit and will result in an unsafe condition. these relay contacts must be force guided contacts. if load is less than 0 m a resistor must be installed across the load. BSr4 4 VDc mpce mpce J earth/ground to machine control Stop circuit J J Output Output B uxiliary monitor relay (non Safety Output) (n.c.) Start 4 4 mpce mpce no external voltage is to be applied to terminals 4 &. Damage to unit will occur. Wrning: rc suppression devices should only be installed across the coils of the machine control relays. never install rc Suppression devices directly across the control output contacts of the BeamSafe. n arc suppression device installed accros the contacts may fail with a short circuit and will result in an unsafe condition. these relay contacts must be forceguided contacts. User supplied over current protection, 4 max. Go to the Engineering Guide For in-depth information on safety standards and use. 8 US Tel. /888/0-47 anada Tel. /8/98-7

6 ccessories mm/in. Front Surface Glass or Stainless Steel Mirror mir4-fg and mir4-ss Brackets mir4bkt mirror StinleSS Steel Or glss mirror SUPPOrt BlOcK mirror StnD PiPe 8..0 mounting tbs (4 PlceS) BSmK Or US Tel. /888/0-47 anada Tel. /8/98-7 9

7 ccessories mm/in. (continued) dapter Kit esbkt (includes DPterS OnlY) DPter lcmk-4 mirror min DPter Laser lignment Tool BSL Laser Level Unit Target lip BEMHEK BeamSafe II BeamSafe II Laser Mounting daptor Go to the Engineering Guide For in-depth information on safety standards and use. 0 US Tel. /888/0-47 anada Tel. /8/98-7

8 Ordering Model No. Description BSX4 Transmitter, 4 VD BSX Transmitter, 8 to 0 V, 0/0 Hz BSX4 Transmitter, 4 VD, ompact Size (This is not compatible with QDX and QDR series connectors) BSR4 Receiver, 4 VD, Relay Output BSR Receiver, 8 to 0 V, 0/0 Hz, Relay Output BSR4 Receiver, 4 VD, ompact Size, Solid-state Output (This is not compatible with QDX and QDR series connectors) ccessories Description MIR4-FG 4 in. mirror for use with MIR4BKT-Front Surface Glass MIR4-SS 4 in. mirror for use with MIR4BKT-Stainless Steel MIR4BKT Bracket for mounting above mirrors at 4 angles for use in double bounce applications (kit mounts one mirror) BSMK Bracket kit. llows mounting of one BeamSafe II transmitter and one BeamSafe II receiver to Omron STI mounting stands ESBKT dapter kit. llows mounting of BSMK and MIR4BKT components to extruded aluminum framing systems and other flat surfaces. MIRS-04 4 ft. stand for mounting mirrors and BeamSafe II units MIRS-0 ft. stand for mounting mirrors and BeamSafe II units QDR- ft., -conductor receiver cable, with quick-disconnect socket QDR-0 0 ft., -conductor receiver cable, with quick-disconnect socket QDR- ft., -conductor receiver cable, with quick-disconnect socket QDX- ft., -conductor transmitter cable, with quick-disconnect socket QDX-0 0 ft., -conductor transmitter cable, with quick-disconnect socket QDX ft., -conductor transmitter cable, with quick-disconnect socket BSL Laser lignment Tool Safety Standards and Precautions The BeamSafe II meets applicable OSH, NSI and RI standards and was designed in accordance with IE49, DIN EN 000 and EN 94-. Only use the BeamSafe II on machinery that stops consistently and immediately anywhere in its cycle or stroke. Never use a BeamSafe II on a full-revolution clutched press or machine. The BeamSafe II is a single optical beam, not a curtain of light. Therefore it is not designed for use as a point-of-operation device. If one or more BeamSafe II systems do not protect all access to the hazardous machine area, the unprotected access must be guarded by fencing, barriers or other appropriate methods. The purchaser, installer and employer are responsible for meeting all appropriate laws, rules and regulations relating to the proper use, installation, operation and maintenance of this control and the guarded machine. For information on safety light curtain accessories, see page D84 US Tel. /888/0-47 anada Tel. /8/98-7