Index Installation Wiring Diagram Variant A (6 pin immobilizer connector)... Wiring Diagram Variant B (8 pin immobilizer connector)...

Transcription

1 Update Alert: Firmware updates are poed to e web on a regular basis. We recomme at you check for firmware a/or inall guide updates prior to inalling is product. Inallation Guide Nissan transpoer interface. Feature include: OEM transpoer immobilizer override via data (no key required) Iex Inallation Wiring Diagram Variant A (6 pin immobilizer connector)... Wiring Diagram Variant B (8 pin immobilizer connector) Module Programming Module Reset LED Diagnoics a Troubleshooting Warranty Vehicle Application Guide The table below lis e vehicles a features which are compatible wi is product. Refer to e following pages for more information on inallation wiring, programming a troubleshooting for ese vehicles. Vehicles Lege: PK: Transpoer & Immobilizer Interface PK-Immobilizre Interface - Data No Key Req'd Nissan Altima Maxima Pafier Sentra X-Trail Nissan is regiered trademarks a property of eir respective companies.

2 Wiring Diagram Variant A (6 Pins Immobilizer Connector) page Remote Starter (-) GWR (Status) Output 8: Yellow: COM Relay 9: Orange/Yellow: Relay (+) v : Red: (+) v : Black: (-) Grou 6: Gray: (+) Ignition Output : Orange/Black: Data DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input RF Loop connector Programming button LED DD P#: XKDD65 ECM SIDE (VEHICLE SIDE) Data Grou Ignition +V Wire Side View IMMOBILIZER MODULE (KEY SIDE) DD connector is not required when inalled in WW mode. Not required in DD mode.

3 Wiring Diagram Variant B (8 Pins Immobilizer Connector) page Remote Starter (-) GWR (Status) Output 8: Yellow: COM Relay 9: Orange/Yellow: Relay (+) v : Red: (+) v : Black: (-) Grou 6: Gray: (+) Ignition Output : Orange/Black: Data DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input ECM SIDE (VEHICLE SIDE) Data Grou Ignition +V Wire Side View RF Loop connector Programming button LED IMMOBILIZER MODULE (KEY SIDE) DD P#: XKDD65 DD connector is not required when inalled in WW mode. Not required in DD mode.

4 Module Programming page Refer to e LED Diagnoics section of is guide for more information a for troubleshooting purposes. Important Make all e required connections to e vehicle, as described in e wiring diagram(s) fou in is guide, a double check to ensure everying is correct prior to moving onto e next ep. Warning! To take advantage of advanced features, you mu use XpressVIP.5 or higher. Using version.9 or. will limit available functions a features.. Connect e interface module to your computer using e XKLoader.. Open an Internet Explorer browser (version 6 or higher), a go to The detail of e platform a firmware at is currently saved on e interface module will be iicated in e top left corner of e page.. Select e year, make a model of e vehicle; e page will refresh to display e compatible firmware.. Click on e FLASH button to upload e firmware onto e interface module. 6. The following message will be displayed when e upload is completed: The flashing is successfully completed. You may now unplug e kit. You can now proceed wi e programming inructions below. OR DD Inallation If required for your inallation, connect e 0-pin, -pin a -pin harnesses to e module, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e 0-pin a -pin harnesses to e module, en connect e -pin harness to e module. DD 0-pin DD 0-pin -pin -pin -pin -pin Wait until e LED turns ON solid red a t urn e ignition ON. Solid & Key in OFF IGN START The green LED turns ON for secos a shuts off. Solid x secs & OFF Turn e ignition OFF. Key out OFF IGN START

5 Module Reset page 5 DD Inallation If required for your inallation, connect e 0-pin, -pin & -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. OR WW Inallation If required for your inallation, connect e 0-pin & -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. 5 DD 0-pin DD 0-pin -pin -pin -pin -pin Wait secos until e LED turns ON solid orange en release e programming button. The LED en turns ON solid red. & & Solid Release Solid LED Diagnoics & Troubleshooting LED Status Description Troubleshooting Module Programming Solid Solid Red. Waiting for e vehicle to be arted. Make sure at all e connections are correct (see inall sheet) a turn e ignition ON to begin e programming sequence. Solid x0 secs Flashes x Solid Red for 0 secos, en flashes x Ignition not detected Check connections. Check if e firmware from unit is correct. Active Grou While Running Flashes Flashes Green continuously. Grou out (GWR) is active. N/A.

6 Limited One Year Consumer Warranty page 6 For a period of ONE YEAR from e date of purchase of a Directed Electronics remote art or security product, Directed Electronics. ( DIRECTED ) promises to e original purchaser, to repair or replace wi a comparable recoitioned piece, e security or remote art accessory piece (hereinafter e Part ), which proves to be defective in workmanship or material uer normal use, provided e following coitions are met: e Part was purchased from an auorized DIRECTED dealer; a e Part is returned to DIRECTED, poage prepaid, along wi a clear, legible copy of e receipt or bill of sale bearing e following information: consumer s name, address, telephone number, e auorized licensed dealer s name a complete product a Part description. This warranty is nontransferable a is automatically void if e Part has been modified or used in a manner contrary to its inteed purpose or e Part has been damaged by accident, unreasonable use, neglect, improper service, inallation or oer causes not arising out of defect in materials or conruction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, ILUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES ILUDING DEALERS OR INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, ILUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, IIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. Some ates do not allow limitations on how long an implied warranty will la or e exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights a you may also have oer rights at vary from State to State. DIRECTED does not a has not auorized any person or entity to create for it any oer obligation, promise, duty or obligation in connection wi is Part This Interface kit / Data Bus Interface part has been teed on e lied vehicles. Oer vehicles will be added to e select vehicle li upon completion of compatibility teing. Visit website for late vehicle application guide. DISCLAIMER: Uer no circumances shall e manufacturer or e diributors of e bypass kit / data bus interface part(s) be held liable for any consequential damages suained in connection wi e part(s) inallation. The manufacturer a it s diributors will not, nor will ey auorize any representative or any oer iividual to assume obligation or liability in relation to e interface kit / data bus interface part(s) oer an its replacement. N.B.: Uer no circumances shall e manufacturer a diributors of is product be liable for consequential damages suained in connection wi is product a neier assumes nor auorizes any representative or oer person to assume for it any obligation or liability oer an e replacement of is product only. Protected by U.S. Patents: 5,79,55; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,75,7 B; 6,97,7 B; 6,6,876 B; 6,9,5 B; 6,59, B; 6,696,97 B; 6,756,885 B; 6,756,886 B; 6,77,67 B; 6,8,89 B; 6,9,750 B; 7,00,0 B; 7,05,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068,5 B; 7,05,679 B; Cdn. Patent:,0,8;,,99;,5,0;,5,0;,5,07;,5,08;,5,0;,0,97;,6,670;,5,089; European Patent:,05,8; Pat. Peing:,9,06. Made in Canada. Additional information can be fou at: