Vehicle Application Guide... Key2GO & 1KEY... Installation (Wiring Diagram & Vehicle Wiring Reference Chart)...

Transcription

1 Update Alert: Firmware updates are posted to e web on a regular basis. We recommend at you check for firmware and/or install guide updates prior to installing is product. Installation Guide Door lock and transponder interface compatible wi specific Chrysler 00 vehicles. To remote start e engine, all doors must be closed, including rear hatch. Index Vehicle Application Guide... KeyGO & KEY... Installation (Wiring Diagram & Vehicle Wiring Reference Chart) Programming Module Programming... Module Reset... Hard Reset... Feature & Option List... Feature Programming LED Diagnostics & Troubleshooting... Limited One-Year Consumer Warranty... Quick Reference Guide... 0 Chrysler is a registered trademark and property of its company.

2 Vehicle Application Guide Page The table below lists e vehicles and features which are compatible wi is product. Refer to e following pages for more information on installation wiring, programming and troubleshooting for ese vehicles. Vehicles 06 0 PK-Immobilizer Bypass-Data No Key Req'd AV-Parking Lights Control CC-Heated Mirrors* CC-Heated Seats Activation* CC-Rear Window Defogger Activation * DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm wi OEM remote KeyGO RS-RAP Shut Down (Retained ACC Power) RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring Chrysler 00 (Smart Key) D D D Legend: D: Data-to-Data (DD) only AV: Horn & Lights Control PK: Transponder & Immobilizer Override : DD and Wire-to-Wire (WW) CC: Comfort & Convenience Controls RS: Remote Start & Status DL: OE Door Lock & Alarm Controls SS: Entry Point Status-Security FOB: Sync CAN Interface w /FOB Remote ST: Function/Feature Status ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status ST-Ignition Status * The Comfort & Convenience Controls (CC) won t work if e vehicle is not equipped wi heated seat features. This feature is mandatory to control e immobilizer override in is firmware. KeyGO has been designed and developed to bypass e advanced encryption layers found in modern vehicles. It uses an array of servers to generate a duplicate of e original key, allowing e installation of a remote starter wiout having to give up a key. The advantage is at is feature allows you to use one original key and e server to configure e bypass in e vehicle. All KeyGO-compatible firmware are clearly indicated in e function list of each vehicle search result page and will also appear on e flash page. Any first-time user must re-register to gain access to KeyGO, and some additional information will be required to complete e registration process, such as your Directed account number and store name. KeyGO requires an XKLoader. Refer to page of is guide for instructions on how to program features using KeyGO.

3 Wiring Diagram Page B A (+) V: Red or Red/Lt. Green, pin A Blue -pin conn. (located at BCM/dash fuse box) [] (-) Hood Status Input (+) Ignition Status Input (+) Brake Input [] IHS CAN High: Gray, pin 8 9 [] (AC) Tach Input (-) Trunk Status Input (-) Door Status Input (-) E-Brake Status Input (-) Ground (-) Ground (+) V 6 Starter C-CAN High: Gray/White, pin 6 Remote OBDII Diagnostic Connector (-) Lock Output (-) Unlock Output (-) Trunk Output (+) Parking Light Output (+) Starter Output (+) Ignition Output (-) GWR (Status) [] IHS CAN Low: White, pin C-CAN Low: Yellow, pin (MUX) Parking Light: White/Brown, pin HS CAN High: Tan/Black: HS CAN Low: Tan: [] MS CAN High: Orange/Green: [] MS CAN Low: Orange/Brown: 6 (MUX) Parking Light Input.: Brown: 7 Parking Light Interrupt. (car side): Yellow: 8 Parking Light Interrupt. (conn. side): Orange/Yellow: 9 (+) Ignition/Start Enable: Yellow/Red: (+) V: Brown/Red: (+) V: Red: (-) Ground (-) Ground: Black: (-) E-Brake Output: Black/White: (-) Door Status Output: Green/White: (-) Trunk Status Output: Red/Black: [] (-) (AC) Tach Output: Violet/White: (+) Brake Output: Gray: 6 (+) Ignition Status Output: Gray/Black: 7 (MUX) Parking Light Output: Violet/Brown: 9 [] (-) Hood Status Output: Blue/Red: RF Prog. Button LED DBALL 0 0: Blue/White: (-) GWR (Status) Input 9: Pink: (+) Ignition Input 8: Violet: (+) Starter Input 7: Pink/White: (+) Parking Light Input : Red/White: (-) Trunk Input : Blue: (-) Unlock Input : Green: (-) Lock Input (+)V RX (-) Ground TX P#: XKDD6 (+) Ignition/Start Enable: Pink/White, pin Black conn. (Located at Parking Light Switch) Black 9-pin connector (Located at link connector attached to e dash frame close to e top left front of e BCM) Not required in DD mode. [] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in DD. [] Required for RAP, heated seats, steering wheel and rear defroster control. [] Some vehicles are not equipped wi OEM hood pin and require e addition of a hood pin for hood sensing. Unless specified oerwise, all connectors are displayed from e wire side, wi e exception of e OBDII diagnostic connector.

4 Vehicle Wiring Reference Chart Page Wire Information Connector Information Function Color Pin Polarity Location Color Pins Chrysler 00 (Smart Key) 0-06 HS CAN High Gray/White 6 Data OBDII diagnostic connector. Black 6 HS CAN Low Yellow Data OBDII diagnostic connector. Black 6 IHS CAN High Gray Data OBDII diagnostic connector. Black 6 IHS CAN Low White Data OBDII diagnostic connector. Black 6 Parking Light White/Brown MUX Located at parking light switch Black 0 Ignition/Start Enable Pink/White (+) Located at link conn. attached to e dash frame close to e top left front of e BCM. Black 9 Ground N/A N/A (-) Chassis Ground. N/A N/A V Red or Red/Lt. Green A (+) Located at BCM/dash fuse box. Blue

5 Module Programming Page Refer to e LED Diagnostics section for more information and for troubleshooting purposes. Important Make all e required connections to e vehicle, as described in e wiring diagram(s) found in is guide, and double check to ensure everying is correct prior to moving onto e next step. Warning! To take advantage of advanced features, you must use XpressVIP. (and higher) or e Directechs Mobile app. Flashing a module using your computer:. Connect e interface module to your computer using e XKLoader.. Go to using Internet Explorer, and select e Flash Module button.. Follow e instructions to select your vehicle, installation type, and configure your options.. Once you have configured e firmware options, click on e FLASH button. Flashing a module using your smartphone or tablet. Connect e interface module to your XKLoader.. Launch e Directechs Mobile app on your smartphone or tablet.. Select FLASH YOUR MODULE and follow e on screen instructions. When e flashing operation is successful, you can proceed wi e programming instructions below. DD Installation If required for your installation, connect e 0-pin, -pin and -pin harnesses to e module, en connect e -pin DD harness. OR WW Installation If required for your installation, connect e 0-pin and -pin harnesses to e module, en connect e -pin harness to e module. st st DD 0-pin DD 0-pin rd nd rd nd -pin -pin -pin -pin Wait until e LED turns ON solid red. Note: To skip e transponder programming and use convenience features only, press e programming button times. The LED will turn orange en proceed to step. To use is firmware as convenience only, you can skip e bypass by pressing e programming button times. Press x Solid Press on e Start/Stop button (PTS) twice to turn e ignition ON ("RUN" illuminates on Start/Stop switch). The LED will flashes orange slowly. Note: If transponder programming was skipped, e LED turns ON solid orange for seconds en shuts off once e module is successfully programmed wiout bypass. Press e PTS button once to switch e vehicle OFF. x PANIC x ENGINE START STOP PUSH x & Flash slowly Press on e Start/Stop button (PTS) once more to turn e ignition OFF. ENGINE START PUSH x STOP Disconnect e module and complete e KeyGO programming. Go to e next page to complete e module programming.

6 Page 6 Web Programming (for KeyGO) Refer to e LED Diagnostics section for more information and for troubleshooting purposes. Version. or higher of XpressVIP must be installed on your computer to complete is programming sequence. Remove e module from e vehicle and reconnect it to your computer. The web site will automatically recognize at you are moving onto e second phase of e programming sequence. Click on Submit KeyGO Request. Once e configuration is completed, reconnect e module. The LED turns ON solid green for seconds, en turns off. Solid x Secs & Off You have successfully completed e module programming sequence.

7 Module Reset Page 7 A module reset will only erase programming performed in e previous steps. All settings (firmware) and settings flashed to e module using e web config tool will not be affected. OR DD Installation If required for your installation, connect e 0-pin, -pin & -pin harnesses to e module. Press and hold e programming button, en connect e -pin DD harness. WW Installation If required for your installation, connect e 0-pin & -pin harnesses to e module. Press and hold e programming button, en connect e -pin harness to e module. st st DD 0-pin DD 0-pin rd nd nd rd -pin -pin -pin -pin Wait seconds until e LED turns ON solid orange en release e programming button. The LED en turns ON solid red. & & Solid Release Solid Hard Reset Warning Against Executing a Hard Reset! A hard reset will revert e flashed firmware back to its default settings. Depending on e installation, some settings (such as RFTD and DD options) may have to be reconfigured. See e Feature & Option List section of is guide. OR DD Installation If required for your installation, connect e 0-pin, -pin & -pin harnesses to e module. Press and hold e programming button, en connect e -pin DD harness. WW Installation If required for your installation, connect e 0-pin & -pin harnesses to e module. Press and hold e programming button, en connect e -pin harness to e module. st st DD 0-pin DD 0-pin rd nd nd rd -pin -pin -pin -pin Wait seconds until e LED turns ON solid orange, and wait 0 more seconds until e LED starts to flash orange and red. Solid & Release e programming button. The LED turns ON solid red. Release & Solid

8 Feature and Option List Page 8 It is recommended to configure all e features and options listed below using e configuration tool found on e module flashing page on The web offers more options; however, manual configuration of e features is possible using e information on is page. Feat. Operation / Option Description. No RF Output* Module is connected to a remote starter using a standard installation. RFTD Output Type. RFTD Output Module is connected to an XL0 using an RSR or RXT installation (when available).. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available). Unlock Driver Priority Heated Seats Defroster Heated Seats/Defroster Temperature Control 6 Heated Seats Temperature Level 7 Automatic Controlled Door Lock 8 Smart OEM Alarm Control. Driver priority* Unlocks only e driver door when e button is first pressed, and unlocks all doors when it is pressed a second time wiin seconds.. All Unlocks all doors when e button is first pressed.. Disabled* No operation.. Enabled When e feature is enabled, it will activate e Heated Seats and heated steering wheel.. Disabled* No operation.. Enabled When e feature is enabled, it will activate e rear defroster and heated mirrors.. F ( 0 C)* When Heated Seats or Defroster feature is enabled, it will activate e feature upon remote start when temperature is below F (0 C).. F (- C) When Heated Seats or Defroster feature is enabled, it will activate e feature upon remote start when temperature is below F (- C).. F (+ C) When Heated Seats or Defroster feature is enabled, it will activate e feature upon remote start when temperature is below F ( C).. Always ON When Heated Seats or Defroster feature is enabled, it will activate e feature at any temperature.. High* When Heated Seats are activated, ey will be set to HIGH.. Low When Heated Seats are activated, ey will be set to LOW.. Disabled* The vehicle doors will not lock automatically.. Ignition The vehicle doors will lock when ignition is turned ON and unlock when ignition is OFF. The vehicle doors will lock when e brake pedal is applied and unlock when ignition is. Brake OFF.. Speed The vehicle doors will lock when speed is sensed and unlock when ignition is OFF. The OEM alarm will not be controlled by e interface upon remote start. No disarm or. Disabled arm command will be executed at e beginning or end of e sequence; it must be controlled by e Remote Starter. Smart OEM Alarm Control will behave like a standard Safelock feature on a remote. Safelock starter. It will unlock at e beginning of e sequence, and relock after start and shutdown. Smart OEM Alarm Control will synchronize wi e OEM alarm so at it will disarm and rearm e vehicle in e remote start sequence, only when required. Smart OEM. Enabled* Alarm Control will monitor e alarm and door lock status to detect if e disarm or rearm is required. If e vehicle is unlocked or is not equipped wi factory alarm, e disarm/rearm will not be executed.

9 Page 9 Feature Programming To enter feature programming routine - Turn e ignition ON, en OFF. - Wiin seconds, press and HOLD e programming button until e LED turns ON orange (after seconds). Release e Programming button. - The LED will flash green once slowly to indicate e feature number is. After a short delay, e LED flashes red rapidly to indicate e current option of feature (i.e. x green followed by x red indicates feature is set to option ). The flashing sequence will repeat until a new command is entered. Changing feature options - Press e lock/arm or unlock/disarm button on aftermarket transmitter to change e option of e selected feature. - The LED flashes red rapidly e number of times equal to e current option number. After a short delay, e LED flashes green slowly e number of times to indicate e current feature. The flashing sequence will repeat until a new command is entered. Accessing anoer feature - Press and release e programming button a number of times to advance from e current feature to e next desired feature. - The LED flashes green slowly e number of times equal to e feature number. After a short delay, e LED flashes red rapidly to indicate e current option of e current feature. The flashing sequence will repeat until a new command is entered. When e maximum number of features or options is reached, e LED will start flashing again from e first feature or option. Once a feature is programmed - Oer features can be programmed. - The feature programming can be exited. Programming Button Exiting feature programming - No activity for 0 seconds; after 0 seconds, e LED will turn ON orange for seconds to confirm e end of e programming sequence. OR - Press and HOLD e programming button for seconds. After seconds, e LED will turn ON orange for seconds to confirm e end of e programming sequence.

10 LED Diagnostics and Troubleshooting Page 0 LED Status Description Troubleshooting Module Programming Off Off Module has no power. Check e power connections. Make sure at e Volt is present between e red and black wires. If it is, e module may be defective. Solid red Solid red Waiting to begin e Make sure at all e connections are correct (refer to e Wiring programming sequence. Diagrams). If a second attempt fails after a complete Hard Reset, connect e Green and red Green and red Initialisation failed. module to Directechs.com and call Tech Support wi e module ID in hand. Solid orange Solid orange Bypass was skipped. Normal operation. green green Bo CAN detected. Normal operation. orange quickly orange quickly CAN detected. orange orange slowly slowly KEYGO Solid green x Solid green x sec. Module was successfully programmed. Solid orange Solid orange x Module was successfully x sec. programmed wiout bypass. Module Programming - Error codes red x red x red x red x red x red x red x red x External Module Synchronization ( red, red, en orange) x0 ( red, red, en orange) x0 Active Ground While Running (status) green green red & orange red & orange green green quickly quickly DD and WW Commands orange orange x x orange orange x x orange orange x x orange orange x6 x6 CAN not detected. CAN not detected. Bypass not detected. Bypass processing error. OBDII feature not supported. GROUND OUT ON (GWR) command received. IGNITION ON command received. START ON command received. LOCK command received. LOCK command received. TRUNK command received. AUX command received. Normal operation. Normal operation. Normal operation. Check e CAN wire connections. Wake up e data bus by turning e ignition on and try again. Some installation types do not need is connection. Skip by pressing e programming button times. Check e CAN wire connections. Wake up e data bus by turning e ignition on and try again. Some installation types do not need is connection. Skip by pressing e programming button times. Check e bypass line connection. If more an one wire is used, make sure ey are not inverted. Start vehicle using e key to confirm e OEM equipment is still operational. The second part of e information was not received. Turn e ignition off en back on to try again. This might be caused by an incorrect reading in e first programming attempt or by an unknown bypass value. If a second or more attempt fails, connect e module to Directechs and call Tech Support wi e module ID in hand. Diagnostic data bus not detected. Some features are not supported by SmartStart. This can be caused by missing wire connections or module hardware limitation. Refer to e wiring installation section to check e connections. Oerwise, e Ground While Running (status) signal was lost or was never received by e module. Commands can come from RF, DD or WW. Oerwise, e ignition signal was not received by e module. In a WW install, it will show only if e ignition input wire is used. Oerwise, e start signal was not received by e module. In a WW install, it will show only if e start input wire is used. Normal operation

11 Limited One Year Consumer Warranty Page For a period of ONE YEAR from e date of purchase of a Directed Electronics remote start or security product, Directed Electronics. ( DIRECTED ) promises to e original purchaser, to repair or replace wi a comparable reconditioned piece, e security or remote start accessory piece (hereinafter e Part ), which proves to be defective in workmanship or material under normal use, provided e following conditions are met: e Part was purchased from an auorized DIRECTED dealer; and e Part is returned to DIRECTED, postage prepaid, along wi a clear, legible copy of e receipt or bill of sale bearing e following information: consumer s name, address, telephone number, e auorized licensed dealer s name and complete product and Part description. This warranty is nontransferable and is automatically void if e Part has been modified or used in a manner contrary to its intended purpose or e Part has been damaged by accident, unreasonable use, neglect, improper service, installation or oer causes not arising out of defect in materials or construction. TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED S OPTION THE PART AS DESCRIBED ABOVE. This warranty only covers Parts sold wiin e United States of America and Canada. Parts sold outside of e United States of America or Canada are sold AS-IS and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or e exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have oer rights at vary from State to State. DIRECTED does not and has not auorized any person or entity to create for it any oer obligation, promise, duty or obligation in connection wi is Part. For furer details relating to warranty information of Directed products, please visit e support section of DIRECTED s website at: This Interface kit / Data Bus Interface part has been tested on e listed vehicles. Oer vehicles will be added to e select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall e manufacturer or e distributors of e bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection wi e part(s) installation. The manufacturer and it s distributors will not, nor will ey auorize any representative or any oer individual to assume obligation or liability in relation to e interface kit / data bus interface part(s) oer an its replacement. N.B.: Under no circumstances shall e manufacturer and distributors of is product be liable for consequential damages sustained in connection wi is product and neier assumes nor auorizes any representative or oer person to assume for it any obligation or liability oer an e replacement of is product only. Protected by U.S. Patents:,79,; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,7,7 B; 6,97,7 B; 6,6,876 B; 6,9, B; 6,9, B; 6,696,97 B; 6,76,88 B; 6,76,886 B; 6,77,67 B; 6,8,89 B; 6,9,70 B; 7,00,0 B; 7,0,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068, B; 7,0,679 B; Cdn. Patent:,0,8;,,99;,,0;,,0;,,07;,,08;,,0;,0,97;,6,670;,,089; European Patent:,0,8; Pat. Pending:,9,06. Made in Canada.

12 Quick Reference Guide DBALL-CHRYSLER0 Vehicle Takeover List of Available Commands Close e vehicle doors, hood and trunk, en press e Remote Start button on e transmitter to start e vehicle.* Press remote start button* Note at e information below is for Viper, Clifford and Pyon models. Icons and commands may differ depending on e remote brand and model purchased. Refer to your auorized installation center for more information. Button(s) Actions Press e Unlock button on e factory or aftermarket remote.* Press Unlock button on eier remote* x x PANIC OR Press & hold for second to lock. Press & hold for second to unlock. Enter e vehicle, while making sure e factory remote is inside wi you. x PANIC x Enter vehicle wi key fob Press & hold for second to remote start. Press & hold for seconds to activate e trunk release (optional). Press Important: Do NOT press e brake pedal. e PTS button twice to turn e ignition ON. Press e brake pedal, put e car in gear and drive off. Do NOT press brake pedal Ready to drive off X ENGINE START STOP PUSH x + x + x + Press once, en to activate e rear hatch/tail glass release (optional).* Press times, en to activate e panic mode. Press once, en to reset e remote starter runtime. * Your aftermarket remote may differ from e model shown in e illustrations. * This output is configurable. see your auorized installation center for more information. Note: There is no vehicle Pit Stop/Idle Mode in is firmware.

13 Quick Reference Guide DBALL-CHRYSLER0 Notes