Index Vehicle Application Guide... Installation - Wiring Diagram... Type 1... Type 2...

Transcription

1 Firmware: BMW0 Rev.: 008 Update Alert: Firmware updates are poed to e web on a regular basis. We recomme at you check for firmware a/or inall guide updates prior to inalling is product. Inallation Guide Doorlock interface for BMW a MINI vehicles. Features include door locks, turn signals, wiows a sunroof, door trigger sensing, hood pin, trunk/hatch a ignition output. Iex Vehicle Application Guide... Inallation - Wiring Diagram... Type... Type Programming Module Programming Module Reset Feature Option Li Feature Programming LD Diagnoics a Troubleshooting Warranty... 0 BMW a MINI are regiered trademarks a property of eir respective companies. 0 Directed. All rights reserved.

2 Firmware: BMW0 Rev.: 008 Vehicle Application Guide The following table lis e vehicles a features which are compatible wi is product. The number assigned to each year allows you to determine which inallation type should be used for your vehicle. page Vehicles BMW Series (8/8) Series (87/88) Series (90/9/9/9) Series (90/9/9/9) Series (60/6) Series (F0/F) 6 Series (6/6) 6 Series (F/F) 7 Series (F0) GT (F07) X (8) X (F) X (70) X6 (7/7) Z (89) Mini Cooper * - not available for all vehicles (it depes on e OM Alarm factory settings) Can be teed by arming e vehicle wi OM remote a unlocking wi mechanical key (if e alarm is disarmed e functions is available) AV-Turn Signal ON/OFF Control CC-Comfort Closure CC-Power Wiows Rolldown DL-Arm Factory Security DL-Disarm Factory Security* DL-Door Lock Control DL-Door Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm wi OM remote SS-ntry Monitoring ALL Door Pins SS-ntry Monitoring Hood Pin SS-ntry Monitoring Trunk/Hatch Pin ST-Ignition Status Lege: D: Data-to-Data (DD) only : DD a Wire-to-Wire (WW) AV: Horn Lights Control CC: Comfort Convenience Controls DL: O Door Lock Alarm Controls FOB: Sync CAN Interface w/ FOB Remote SS: ntry Point Status-Security ST: Function/Feature Status 0 Directed. All rights reserved.

3 Firmware: BMW0 INSTALLATION TYP Rev.: 008 page (-) Grou (+) V (-) Trunk Status Input (+) Ignition Input (-) Hood Status Input (-) Door Status Input (-) Grou (+) V Syem Security (-) Lock Output (-) Unlock Output (-) Trunk Release Output Aux Output Aux Output (+) Parking Lights Output Twied pair in Can Gateway module, driver side uer dashboa CAN High: Yellow/Red CAN Low: Yellow/Brown : Tan/Black: HS CAN High : Tan: HS CAN Low (+)V (-) Grou : Red: (+) V : Black: (-) Grou : Green/Black: Door Status Output : Green/White: Trunk Status Output 7: Gray/Black: (+) Ignition Output : Blue/Red: Hood Status Intput DBALL RF Loop connector 0 7: Pink/White: (+) Parking Lights Input : Violet/Black: (-) AUX Input* : White/Violet: (-) AUX Input* : Red/White: (-) Trunk Release Input : Blue: (-) Unlock Input : Green: (-) Lock Input Programming button LD Locating components in e vehicle BMW Series (F0) Can Gateway Can H - Yellow/Red Can L - Yellow/Brown NOT: Pictures are representative for BMW Series. For oer models it is possible to differ e location of modules a wires color (except CAN wires) 0 Directed. All rights reserved.

4 Firmware: BMW0 INSTALLATION TYP Rev.: 008 page (-) Grou (+) V (-) Trunk Status Input (+) Ignition Input (-) Hood Status Input (-) Door Status Input (-) Grou (+) V Syem Security (-) Lock Output (-) Unlock Output (-) Trunk Release Output Aux Output Aux Output (+) Parking Lights Output Twied pair in driver kick panel Series, Series, X, X, X6, Z Series, 6 Series CAN High: Orange/Green CAN Low: Green OR CAN High: Black CAN Low: Yellow : Orange/Green: FT CAN High 6: Orange/Brown: FT CAN Low (+)V (-) Grou : Red: (+) V : Black: (-) Grou : Green/Black: Door Status Output : Green/White: Trunk Status Output 7: Gray/Black: (+) Ignition Output : Blue/Red: Hood Status Intput DBALL RF Loop connector 0 7: Pink/White: (+) Parking Lights Input : Violet/Black: (-) AUX Input* : White/Violet: (-) AUX Input* : Red/White: (-) Trunk Release Input : Blue: (-) Unlock Input : Green: (-) Lock Input Programming button LD 0 Directed. All rights reserved.

5 Firmware: BMW0 Module Programming Rev.: 008 page Refer to e LD Diagnoics section of is guide for more information a for troubleshooting purposes. Important Make all e required connections to e vehicle, as described in e wiring diagram(s) fou in is guide, a double check to ensure everying is correct prior to moving onto e next ep. Warning! To take advantage of advanced features, you mu use XpressVIP. or higher. Using version.9 or. will limit available functions a features.. Connect e interface module to your computer using e XKLoader.. Open an Internet xplorer browser (version 6 or higher), a go to The detail of e platform a firmware at is currently saved on e interface module will be iicated in e top left corner of e page.. Select e year, make a model of e vehicle; e page will refresh to display e compatible firmware.. In e search result page, select one of e available inall options (config for RSR, RXT or Staa inall), a follow e inructions provided on e screen.. Once you have configured your options, click on e FLASH button to upload e firmware onto e interface module. 6. The following message will be displayed when e upload is completed: The flashing is successfully completed. You may now unplug e kit. You can now proceed wi e programming inructions below. For Type vehicles OR DD Inallation If required for your inallation, connect e, -pin a -pin harnesses to e module, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e a -pin harnesses to e module, en connect e -pin harness to e module. DD DD -pin -pin -pin -pin Wait until e LD turns ON solid red a press e Unlock button on e OM remote. Make sure e key is inside e vehicle. Key Inside e Vehicle Important: Do NOT press e brake pedal. Press e Push-to-Start (PTS) button twice to turn e ignition ON. Do NOT press e brake pedal X PUSH STOP NGIN The LD turns ON solid green for secos, en turns OFF once e module has been successfully programmed. Green x secs OFF 6 Press Once Push-to-Start (PTS) to turn e Ignition OFF X PUSH STOP NGIN Go to e next page to complete e module programming for type a vehicles. 0 Directed. All rights reserved.

6 Firmware: BMW0 Rev.: 008 page 6 OR DD Inallation If required for your inallation, connect e, -pin a -pin harnesses to e module, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e a -pin harnesses to e module, en connect e -pin harness to e module. DD DD -pin -pin -pin -pin Wait until e LD turns ON solid red a press e Unlock button on e OM remote. For Type vehicles Important: Do NOT press e brake pedal. Insert e key into e key slot. Press e Push-to-Start (PTS) button once to turn e ignition ON. Do NOT press e brake pedal Insert Key X PUSH STOP NGIN The green LD turns ON for secos a shuts off. x secs OFF Press e Push-to-Start (PTS) button once to turn e ignition OFF. Remove e key from e key slot. X PUSH STOP Remove Key For Type vehicles Turn e ignition ON. Key OFF IGN The green LD turns ON for secos a shuts off. x secs OFF 6 Turn e ignition OFF. Key OUT OFF IGN 0 Directed. All rights reserved.

7 Firmware: BMW0 Module Reset Rev.: 008 page 7 A module reset will erase e module programming only (bypass, convenience a vehicle detection). All e settings configured on e module using e web config tool will remain untouched. DD Inallation If required for your inallation, connect e, -pin -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. OR WW Inallation If required for your inallation, connect e -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. DD DD -pin -pin -pin -pin Wait secos until e LD turns ON solid orange en release e programming button. The LD en turns ON solid red. Release Ha Reset Warning Again xecuting a Ha Reset! A ha reset will erase all e data ored in e DBALL a will change all e settings configured on e module to its default values. After a ha reset, you may have to reconfigure your DBALL if your inallation requires specific options, not part of e default configuration. See e Feature Option Li section of is guide. OR DD Inallation If required for your inallation, connect e, -pin -pin harnesses to e module. Press a hold e programming button, en connect e -pin DD harness. WW Inallation If required for your inallation, connect e -pin harnesses to e module. Press a hold e programming button, en connect e -pin harness to e module. DD DD -pin -pin -pin -pin Wait secos until e LD turns ON solid orange, a wait 0 more secos until e LD arts to flash orange a red. Flashes Release e programming button. The LD turns ON solid red. Release 0 Directed. All rights reserved.

8 Firmware: BMW0 Feature Option Li Rev.: 008 page 8 It is recommeed to configure all e features a options lied below using e configuration tool fou on e module flashing page on The web offers more options; however, a manual configuration of e features is possible using e information on is page. Feat. Operation Flashes/Options Description N/A N/A Comfort Closure. Disabled*. nabled N/A N/A 6 N/A AUX AUX AUX N/A. OFF*. Wiows Roll Up. Front Wiows Roll Down. Rear Wiows Roll Down. OFF*. Wiows Roll Up. Front Wiows Roll Down. Rear Wiows Roll Down. OFF*. Wiows Roll Up. Front Wiows Roll Down. Rear Wiows Roll Down Feature Programming To enter feature programming routine - Turn e ignition ON, en OFF. - Wiin secos, press a HOLD e programming button until e LD turns ON orange (after secos). Release e Programming button. - The LD will flash green once slowly to iicate e feature number is. After a short delay, e LD flashes red rapidly to iicate e current option of feature (i.e. x green followed by x red iicates feature is set to option ). The flashing sequence will repeat until a new comma is entered. Changing feature options - Press e lock/arm or unlock/disarm button on aftermarket transmitter to change e option of e selected feature. - The LD flashes red rapidly e number of times equal to e current option number. After a short delay, e LD flashes green slowly e number of times to iicate e current feature. The flashing sequence will repeat until a new comma is entered. Accessing anoer feature - Press a release e programming button a number of times to advance from e current feature to e next desired feature. - The LD flashes green slowly e number of times equal to e feature number. After a short delay, e LD flashes red rapidly to iicate e current option of e current feature. The flashing sequence will repeat until a new comma is entered. When e maximum number of features or options is reached, e LD will art flashing again from e fir feature or option. Once a feature is programmed - Oer features can be programmed. - The feature programming can be exited. Programming Button xiting feature programming - No activity for 0 secos; after 0 secos, e LD will turn ON orange for secos to confirm e e of e programming sequence. OR - Press a HOLD e programming button for secos. After secos, e LD will turn ON orange for secos to confirm e e of e programming sequence. 0 Directed. All rights reserved.

9 Firmware: BMW0 LD Diagnoics Troubleshooting Rev.: 008 page 9 LD Status Description Troubleshooting Module Programming Red. Waiting for e vehicle to be arted. Make sure at all e connections are correct (see inall sheet) a turn e ignition ON to begin e programming sequence. x0 secs Flashes x Red for 0 secos, en flashes x FT CAN not detected. The CAN wires may be incorrectly connected. Refer to e wiring diagram to make e right connections. x0 secs Flashes x Red for 0 secos, en flashes x HS CAN not detected. The CAN wires may be incorrectly connected. Refer to e wiring diagram to make e right connections. x0 secs Flashes x Red for 0 secos, en flashes x Ignition not detected The CAN bus was detected but e ignition on CAN message is not detected. Check if e firmware from unit is correct. Flashes Flashes Green continuously. Ignition has been successfully detected. Car detection in progress N/A. x secs Green for secos. Module has been successfully programmed. N/A. Inactive Grou While Running Flashes x Flashes x Flashes x Flashes x Flashes x Flashes Green x Flashes Green x Flashes Green x Flashes Green x Flashes Green x Lock comma has been received. Unlock comma received. has been Trunk release comma been received. has AUX comma has been received. AUX comma received. has been If it does not flash, e bypass module did not receive e signal. Verify e connections between e bypass a e remote arter module. If it does not flash, e bypass module did not receive e signal. Verify e connections between e bypass a e remote arter module. If it does not flash, e bypass module did not receive e signal. Verify e connections between e bypass a e remote arter module. If it does not flash, e bypass module did not receive e signal. Verify e connections between e bypass a e remote arter module. If it does not flash, e bypass module did not receive e signal. Verify e connections between e bypass a e remote arter module. 0 Directed. All rights reserved.

10 Firmware: BMW0 Limited One Year Consumer Warranty Rev.: 008 page 0 For a period of ON YAR from e date of purchase of a Directed lectronics remote art or security product, Directed lectronics. ( DIRCTD ) promises to e original purchaser, to repair or replace wi a comparable recoitioned piece, e security or remote art accessory piece (hereinafter e Part ), which proves to be defective in workmanship or material uer normal use, provided e following coitions are met: e Part was purchased from an auorized DIRCTD dealer; a e Part is returned to DIRCTD, poage prepaid, along wi a clear, legible copy of e receipt or bill of sale bearing e following information: consumer s name, address, telephone number, e auorized licensed dealer s name a complete product a Part description. This warranty is nontransferable a is automatically void if e Part has been modified or used in a manner contrary to its inteed purpose or e Part has been damaged by accident, unreasonable use, neglect, improper service, inallation or oer causes not arising out of defect in materials or conruction. TO TH MAXIMUM XTNT ALLOWD BY LAW, XCPT AS STATD ABOV, ALL WARRANTIS, INCLUDING BUT NOT LIMITD TO XPRSS WARRANTY, IMPLID WARRANTY, WARRANTY OF MRCHANTABILITY, FITNSS FOR PARTICULAR PURPOS AND WARRANTY OF NONINFRINGMNT OF INTLLCTUAL PROPRTY, AR XPRSSLY XCLUDD; AND DIRCTD NITHR ASSUMS NOR AUTHORIZS ANY PRSON OR NTITY TO ASSUM FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNCTION WITH ITS PRODUCTS. DIRCTD HRBY DISCLAIMS AND HAS ABSOLUTLY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIS INCLUDING DALRS OR INSTALLRS. IN TH VNT OF A CLAIM OR A DISPUT INVOLVING DIRCTD OR ITS SUBSIDIARY, TH PROPR VNU SHALL B SAN DIGO COUNTY IN TH STAT OF CALIFORNIA. CALIFORNIA STAT LAWS AND APPLICABL FDRAL LAWS SHALL APPLY AND GOVRN TH DISPUT. TH MAXIMUM RCOVRY UNDR ANY CLAIM AGAINST DIRCTD SHALL B STRICTLY LIMITD TO TH AUTHORIZD DIRCTD DALR S PURCHAS PRIC OF TH PART. DIRCTD SHALL NOT B RSPONSIBL FOR ANY DAMAGS WHATSOVR, INCLUDING BUT NOT LIMITD TO, ANY CONSQUNTIAL DAMAGS, INCIDNTAL DAMAGS, DAMAGS FOR TH LOSS OF TIM, LOSS OF ARNINGS, COMMRCIAL LOSS, LOSS OF CONOMIC OPPORTUNITY AND TH LIK. NOTWITHSTANDING TH ABOV, TH MANUFACTURR DOS OFFR A LIMITD WARRANTY TO RPLAC OR RPAIR AT DIRCTD S OPTION TH PART AS DSCRIBD ABOV. Some ates do not allow limitations on how long an implied warranty will la or e exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights a you may also have oer rights at vary from State to State. DIRCTD does not a has not auorized any person or entity to create for it any oer obligation, promise, duty or obligation in connection wi is Part This Interface kit / Data Bus Interface part has been teed on e lied vehicles. Oer vehicles will be added to e select vehicle li upon completion of compatibility teing. Visit website for late vehicle application guide. DISCLAIMR: Uer no circumances shall e manufacturer or e diributors of e bypass kit / data bus interface part(s) be held liable for any consequential damages suained in connection wi e part(s) inallation. The manufacturer a it s diributors will not, nor will ey auorize any representative or any oer iividual to assume obligation or liability in relation to e interface kit / data bus interface part(s) oer an its replacement. N.B.: Uer no circumances shall e manufacturer a diributors of is product be liable for consequential damages suained in connection wi is product a neier assumes nor auorizes any representative or oer person to assume for it any obligation or liability oer an e replacement of is product only. Protected by U.S. Patents:,79,; 6,0,60 B *; 6,,00 B; 6,9,6 B; 6,7,7 B; 6,97,7 B; 6,6,876 B; 6,9, B; 6,9, B; 6,696,97 B; 6,76,88 B; 6,76,886 B; 6,77,67 B; 6,8,89 B; 6,9,70 B; 7,00,0 B; 7,0,80 B; 7,0,86 B; 7,06,6 B; 7,06,7 B; 7,068, B; 7,0,679 B; Cdn. Patent:,0,8;,,99;,,0;,,0;,,07;,,08;,,0;,0,97;,6,670;,,089; uropean Patent:,0,8; Pat. Peing:,9,06. Made in Canada. Additional information can be fou at: Directed. All rights reserved.