Chapter. Accessories. In This Chapter...

Transcription

1 ccessories hapter In This hapter... ccessories Overview... - / Power dapter... - / Power dapter imensions... - / Power dapter Installation SU -pin to Terminal lock dapters... - Non-glare Screen overs... - lear Screen Overlay Installation... - S ard US FLSH rive... -0

2 hapter - ccessories 0 ccessories Overview Part Number E- E--OV E--OV E--OV E-0-OV E-0W-OV E--OV E--OV E-S-R US-FLSH E-OMON- or E-OMON- E- / Power dapter -more Touch Panel E-OMON- or E-EOMON- SU Port dapter US-FLSH US Pen rive E-x-OV Screen Protector E-S-R S ard escription / dapter for -more E and E series touch panels; powered from a 00-0 V, 0/0 Hertz power source. Provides V at.. Power Fault features help protect data being logged to ompact Flash or S card during power failures. -more E series panels must have firmware version. uild.e or higher for proper operation. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series and -more Micro-Graphic -inch panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E series -inch panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series -inch panels. Package of. Non-glare protective overlay, 0-inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series 0-inch panels. Package of. Non-glare protective overlay, 0-inch widescreen, protects -more touch screen and helps reduce glare from external light sources. ompatible with E-T0WL panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series -inch panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series -inch panels. Package of. S memory card for non-volatile storage, G industrial grade. degrees maximum operating temperature makes it suitable for data logging in industrial applications. Recommended for the -more E series touch panels. US Flash drive, Sanisk, G (Sanisk P/N SZ0-0G-). Recommended for use with the -more touch panels and Productivity000 controllers. -SU -pin to -terminal PL serial communication port adapter to allow wire terminal connections for RS-/ PL communication cable. E-OMON- is low profile and fits E-TL-R, E-TL, E-TL and E-TL-R E-OMON- is straight and fits E-TL, E-T0L, E-TL and E-TL - E-USER-M Hardware User Manual, st Ed. Rev. G

3 hapter - ccessories / Power dapter The optional -more / Power dapter can be used to power the -more touch panels from a 00-0 V, 0/0 Hertz, voltage source. The adapter provides to the touch panel s power connector and can be conveniently secured to the touch panel with two captive screws. The adapter provides a power loss signal to the touch panel that causes the touch panel to stop writing data to S memory devices providing a controlled shutdown for increased data logging reliability. Part No. E V 0/0 Hz / dapter Wiring Recommended Supply Fuse.0 time delay, p/n ML Power dapter Not recommended for use with the E-T when operating temperatures are expected to be above 0 deg. Tightening Torque Power supply cable torque - oz-in ( Nm) Power connector mounting torque - oz-in ( Nm) Mounting flange screw torque - oz-in ( Nm) Warning: Use 0 / copper conductors only. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

4 hapter - ccessories 0 / Power dapter Specifications Part Number E- Input Voltage & frequency 00-0 V; 0/0 Hertz Operating Temperature Range 0 to 0 [ to F] Maximum surrounding temperature rating, 0 Storage Temperature Range -0 to 0 [- to 0 F] Operating & Storage Humidity 0-% RH (non-condensing) Noise Immunity 000 V p-p (Pulse width µs, rise time: ns) With proper ground connection on terminal block. Hi-pot 000 V, minute With proper ground connection on terminal block. Insulation Resistance 00 V, 0 M ohm or above With proper ground connection on terminal block. Vibration ompliant with IE- Shock Pulse shape: Sine half wave, Peak acceleration: m/s ( G), X, Y, Z: directions, times each Thermal Protection 0 [ F], with autorecovery Short ircuit Protection V:., 00 V:., V:. Static Electricity ischarge Resistance ompliant with IE000--, ontact: kv, ir: kv gency pprovals UL0, UL Recognized, cul, E, EM EN- Environment For use in pollution degree environment Grounding Ground resistance: less than 00 ohm Weight. oz. [ g] Removable Power onnector E--ON or E Switchlab M0-0-0G Secure with () captive M. screws, torque to 0 oz-in [0. Nm] Output urrent Maximum. Inrush urrent For 00 V:, ms or less For 0 V: 0, ms or less Recommended Supply Fuse.0 time delay, p/n ML Power Supply able Torque - oz-in ( Nm) Mounting to Touch Panel Secure with () spring loaded captive M-0 screws, torque to 0 oz-in [0. Nm] NOTE: Logic within the E- will turn off the backlight instantly when a power failure is detected to allow the PU to run longer. The backlight turns on automatically when the power returns to the -more operating voltage. - E-USER-M Hardware User Manual, st Ed. Rev. G

5 hapter - ccessories Screw / Power dapter imensions.00 [.] Power onnector. ±0.0 [. ± 0.] 0. [.]. [.0] Power Label imensions Power FRONT VIEW Screw SIE VIEW onnector RER VIEW OTTOM VIEW Units: inches [mm] Panel epth with / Power dapter Installed Units: inches[mm] Part Number E-TL-R. [.0] E-TL. [.0] E-TL-R. [.0] E-TL. [.0] E-TL. [.] E-T0L. [.] E-T0WL. [.] E-TL. [.] E-TL-R. [.] E-TL. [.] 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

6 hapter - ccessories 0 / Power dapter Installation WRNING: This procedure should only be performed by qualified personnel who are experienced in working with electronic equipment. Take the necessary steps to prevent damage that may be caused by static electricity discharge. isconnect input power to the touch panel before proceeding. Preparation: Place the touch panel face down on a lint-free soft surface to prevent scratching the display screen if not already installed in a control cabinet. Remove the power connector if it is installed. Secure the / Power dapter to the touch panel by tightening the two () spring loaded captive M-0 screws to a torque of 0 oz-in [0. Nm]. Insert the / power adapter into the touch panel s -position power connector. Plug the wired -pin Power onnector into its mating connector on the adapter and secure in place by tightening the two () captive M. screws to a torque of 0 oz-in [0. Nm]. - E-USER-M Hardware User Manual, st Ed. Rev. G

7 KOYO ELETRONIS INUSTRIES O., LT. hapter - ccessories -SU -pin to Terminal lock dapters These adapters are plugged into the -pin serial port on the rear of the panels to allow wire terminal connections for RS-/ PL communication cable. The wiring of both adapters is the same.. [.] E-OMON- is used with E-TL-R, E-TL, E-TL-R and E-TL. E-OMON- is UL Recognized. E-OMON- is NOT UL Recognized or Listed. It is used with E-TL, E-T0L, E-TL, E-TL-R and E-TL E-OMON- E-OMON- imensions. [.] Wiring iagram Units: inches [mm]. [.] Terminals GN S S+ R R+ TERM ate code ountry of Origin E-OMON- GN S S+ R R+ TERM 0. [.] -SU -pin to Terminal lock dapters (P/Ns E-OMON- & E-OMON-) GN S S+ R R+ TERM Wiring iagram imensions GN TX TX+ 0 RX RX+ TERM 0.0 [.] Units: inches [mm] -pin -sub (male).0 [.].0 [.] 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

8 hapter - ccessories 0 Non-glare Screen overs Non -glare PET screen covers are protective overlays used to protect the touch screen and help reduce glare from external light sources. (pk of ) Part No. E--OV, E--OV, E--OV, E-0-OV, E-0W-OV, E--OV & E--OV E-xx-OV Non-glare Screen overs imensions - inches [mm] Part Number E--OV. [.].0 [.] E--OV.0 [.].00 [0.] E--OV. [.]. [.] E-0-OV. [.]. [.0] E-0W-OV. [.]. [.] E--OV 0. [0.]. [.] E--OV. [.]. [.] 0. [.0] 0. [.0] - E-USER-M Hardware User Manual, st Ed. Rev. G

9 hapter - ccessories Non-glare Screen overs (cont d) lear Screen Overlay Installation Step heck to be sure that the proper size non-glare screen cover is being used on the subject touch panel. Notice that the outer perimeter of the screen cover has an adhesive band. The adhesive band will be located on the outside edge of the touch panel s white frame bordering the touch area when installed. Step lign the screen cover over the touch panel s white frame, then start on one side and gently lay the cover over the entire touch area. Step Remove the protective sheet. Step Start in one corner and peel the screen cover from the backing. Step Smooth out the screen cover and press all around the outside perimeter to secure the cover in place. The screen cover can be removed by lifting up on the small tab and gently pulling the cover away form the touch panel s surface. NOTE: The protective cover ships with a thin protective sheet on the face of the cover that needs to be carefully removed. If your panel is not clear, the protective sheet may not have been removed. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

10 hapter - ccessories 0 S ard S memory card for non-volatile storage, G industrial grade. maximum operating temperature makes it suitable for data logging in industrial applications. Recommended for the -more E series touch panels. The S card is the fastest option for writing data. If logged data is saved to external memory, utomationirect recommends using an E-S-R. US FLSH rive US-FLSH sold by utomationirect has been tested with -more panels and is Hi-Speed US.0 certified. Part No. US-FLSH -0 E-USER-M Hardware User Manual, st Ed. Rev. G