Phoenix Install 4m 12/12
|
|
- Gillian Morrison
- 5 years ago
- Views:
Transcription
1 Phoenix Install 4m 12/12 Place Instrument Change in Progress sign on console Follow instructions for removing the cage bottom Once removed, add or remove the appropriate rocket weights If necessary, follow instructions for installing the rotator and guider If the interface is not already attached to Phoenix attach it to the instrument first In the coude room, remove the stabilizing blocks holding the interface to the plate Loop three lifting straps through the holes in the vertical pieces on the interface (as seen above) and attach them to the jib crane Raise the interface with the crane and roll the cart out of the way Remove the top nut washer pair from the 11 threaded studs atop Phoenix Remove the light port cover from the top of Phoenix
2 Turn off the compressors running the Phoenix cooling, located on the control room floor In the coude room Turn off the motor controller Turn off the Electronics box Disconnect the He lines from the wall NOTE: After disconnecting the lines you have 1 hour to install the instrument and hook the lines back up Remove the He lines from Phoenix so the side of the cart can be removed once Phoenix is attached to the telescope Disconnect the power, fibers and the ethernet cable If the interface is not attached to Phoenix move Phoenix under the interface Make sure to line Phoenix up in the proper N-S direction and in the proper holes for the 4m Two of the 4 tabs on the top of the interface are marked, one N-4m and one S-4m Line the bird on Phoenix up with the S-4m tab Line the interface up so the 4m holes line up with the threaded studs on Phoenix Place the foam ring on top of Phoenix
3 Use the crane to lower the interface onto Phoenix Reattach the washers and nuts Lower all the feet on the underside of the interface until they contact Phoenix Remove the lifting straps from the interface Wheel Phoenix onto the instrument lift and line up with the Phoenix marks on the floor Remove the bolts that have been placed through the holes on the top of the interface Remove the red cover off the top of the interface
4 Raise the lift Attach Phoenix to the telescope, noting the proper N direction for the 4m If need be, use the jack on the cart, until the interface is flush with the telescope If used, lower the Phoenix jack Remove the cart railing on the west side Connect the He lines Plug in the two AC power cords Make sure the motor control box is turned off Lower the platform On the control room level, turn on one of the compressors Follow the instructions for attaching the cage bottom While doing so, turn on the motor control power Plug in the private network cable Hook up the Phoenix fiber bundle Hook up the two cables to the interface If Phoenix was at the 2m prior to 4m installation, the cables will be secured on the S side of the instrument and have to be unsecured and moved to the N side to plug them in Turn on the electronics box Plug in the Phoenix video power and video, on the W side of the instrument, to ICCD 2 on the rotator cable bridge patch panel Hook up the exhaust hose Hook up the N2 line Install the refocusing lens on the north port camera Install the refocusing lens on the guide camera
5 If necessary, follow the instructions for doing a secondary flip from F/8 to PF While at the SE Annex Hook up the pedestal focus handpaddle inside the PF cage Move the pedestal focus all the way out On the flip panel the minor flip ready will now light up Press and hold the F/12 button until the mirror is all the way in place Switch the vacuum from F/8 to F/12
6 Hook up all the cables in box 1 on the ring, except J2
7 Return the telescope to zenith Follow instructions for balancing the telescope In the computer room, switch the fibers from the coude connection to the telescope wildfire connection
ColorMaxLP Label Roll Rewinder
ColorMaxLP Label Roll Rewinder 5/2017 INSTALLATION/OPERATOR MANUAL Included: Rewinder Base plate Power supply Power Cord Thumb screws Assembly instructions 1. Install base plate Lift front of printer and
More informationAPC Open Frame Rack Networking Solutions
APC Open Frame Rack Networking Solutions NetShelter 2- and 4 Post Open Frame Racks The NetShelter 2 and 4 Post Open Frame Racks offer a quality solution for the economical installation of rackmountable
More informationInnovative Americans, LLC. HD Media Pack Installation Manual
Innovative Americans, LLC HD Media Pack Installation Manual Please read this manual before you begin! Your installation will be EASIER and SAFER if you take a few moments to read this document!! Proudly
More informationBL-FLOWSTN-P FlowStation Module Installation Guide
Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port
More informationINSTALLATION INSTRUCTIONS Version 2.4
INSTALLATION INSTRUCTIONS Version 2.4 11/12/2012 Patient Point, LLC 8230 Montgomery Road, Suite 300 Cincinnati, Ohio 45236 1-800-287-0908 TABLE OF CONTENTS System Overview 2 Tool List. 3 Installation Process
More informationMain Library Meeting Room Use
Main Library Meeting Room Use Occupancy: Meeting Room A: 100 Meeting Room B: 50 Meeting Room C: 50 Combined A, B & C: 300 Conference Room: 20 Tables: 50 (2x5 ), 4 (3 ), and 16 round (6 ) Chairs: 290 This
More informationELITE Test Systems. /Quick Start Wiring. Botron Company Inc.
ELITE Test Systems 01 /Quick Start Wiring Botron Company Inc. GETTING TO KNOW YOUR ELITE P1 This guide shows you how to assemble and wire your ELITE Test System, and gets you ready for everyday use. Once
More informationDYNAVISION D2 TM INSTALLATION MANUAL
DYNAVISION D2 TM INSTALLATION MANUAL Rev 12 Dynavision International 8800 Global Way, West Chester, Ohio 45069 USA EMAIL:info@dynavisiond2.com, WEBSITE: www.dynavisiond2.com, FAX: (905) 294-6327 Unpacking
More informationLCD Series & Tablet Series Set-Up Instructions
LCD Series & Tablet Series Set-Up Instructions Parts List: Mount Arm (1) T-Nut (1) Large Camera Knob (1) Small Camera Knob (1) Mirror Knob (2) Monitor/Mirror Assembly (1) Teleprompter Parts Step #1A Remove
More informationVacuum Maintenance Manual (EXCERPT Tim Benedict)
1. Position a ladder, scaffold, or work stand, on the right side of Vacuum Skid where the blower motors are installed. 2. Locate the six (6) vacuum hoses connecting the blower motors to the HEPA housings
More informationAttaching DX Encoders to your Majestic Carriage
Attaching DX Encoders to your Majestic Carriage Encoders are the white wheels that you need to have on your carriage in order for the stitch regulation to work. Encoders detect the movement of the machine
More informationProbe station system
Probe station system Manufacturer: Micromanipulator Mode: 450PM-HR Descriptions: The Model 450PM 8 probe station offers stable and reliable probing performance. It is based on a design of Micromanipulator
More informationMAGIXBOX TM. Quick Start Guide
TM TM by TouchMagix MAGIXBOX TM Quick Start Guide What s in the box: Ankle Ceiling Plate Extendable Rod Connector Piece Middle Piece Universal Spider Super clamp with ball socket Safety Cable Projector
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationPeel/Rewind Upgrade Kit
Peel/Rewind Upgrade Kit Installation Instructions This kit includes the parts and documentation necessary to install the Peel/Rewind upgrade kit on the following printers: ZM400 ZM600 Read these instructions
More informationSite Preparation CHAPTER
CHAPTER 3 Site Preparation This chapter describes the steps to take and the considerations you should keep in mind prior to installing the modules in an open rack. It also contains information that applies
More informationPower Series Camera Support
Power Series Camera Support Power Jib Power Column Power Dolly Power Series Camera Support Equipment Assembly Manual Remark: Before assemble the jib, please check the inventory and read this manual carefully
More informationD-Net CABINETS. D-Net cabinets are a versatile racking system suitable for housing
D-Net CABINETS D-Net cabinets are a versatile racking system suitable for housing networking and various structured cabling components. D-Net Cabinets are manufactured in Taiwan in compliance with ISO9001:2000
More informationCIB 2924 Line-Powered Alert Ringer and Parts
CIB 2924 Line-Powered Alert Ringer and Parts CIB 2924 Comcode 103-974-697 Issue 1 CIB 2924 Line-Powered Alert Ringer and Parts The D181233 Line-Powered Alert Ringer and Parts (see Figure 1) consists of
More informationIRF90 - Rotating Focuser
IRF90 - Rotating Focuser Part # 600180 REV092111 Page 1 Contents Introduction and Overview... 3 Limitations... 3 Packing List... 4 Installation... 5 Remove Existing Focuser... 5 Installing the Rotating
More informationNikon D5000 Viewfinder Replacement
Nikon D5000 Viewfinder Replacement Disassembly down to the viewfinder hood and to the screen itself. Written By: Jacob Rardin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION If there is dust
More information7409 K570. Generic Pinpad Mount. Kit Instructions. Issue B
7409 K570 Generic Pinpad Mount Kit Instructions Issue B Revision Record Issue Date Remarks A Jun 2009 First issue B Mar 2011 Added 7409 K060 support 1 Introduction This kit provides an arm that is used
More informationSnap Server 4400 Power Supply
Snap Server 4400 Power Supply Snap Server 4400 Note You can set up your system to send an e-mail alert in the event of a hardware failure. For details, see the section on e-mail notification in your Administrator
More informationMAIN OPERATING INSTRUCTIONS
MAIN OPERATING INSTRUCTIONS VPS-1 Pedestal Including Dolly options & accessories 1. INTRODUCTION You have bought a Pedestal out of the expanding new Cambo range of Video products. We expect that you will
More informationDelta T Dew Heater for CDK
Delta T Dew Heater for CDK Delta T Dew Heater for CDK12.5 (125902) Your CDK 12.5 Delta T Dew Heater includes the following: QTY 1 Delta T control box w/ mounting bracket attached 1 2.5Amp AC adapter 2
More information15U Wall-Mount Server Rack Cabinet - 20 in. Deep - Hinged
15U Wall-Mount Server Rack Cabinet - 20 in. Deep - Hinged Product ID: RK1520WALHM This 15U server or network rack cabinet lets you mount your EIA-310 compliant equipment to the wall, in a secure enclosure
More informationThe Ridgeview Tripod. Your Ridgeview TM tripod is a mid-size field-packing tripod with a ball head for fast operation. Quick-Release Plate
The Ridgeview Tripod Your Ridgeview TM tripod is a mid-size field-packing tripod with a ball head for fast operation. Plate Center Column Collar Compact Ball Head Bubble Level Compass Foam Padding Leg
More informationParts List: Assembly Instructions:
My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord
More informationDaNI Robot Camera. User Guide V0512
DaNI Robot Camera User Guide 60018 V0512 Materials Included Camera (includes hardware that will not be used) Modem (with power supply that will not be used) Power converter 6" Velcro strip Adhesive tab
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following: v Two
More informationImprove the appearance and accessibility of your rack
Vertical Cable Organizer with D-Ring Hooks - 0U - 6 ft. StarTech ID: CMVER40UD This 6-foot vertical cable manager (2 x 3-foot panels) gives you a simple and space-efficient way to organize the cables in
More informationIBM. Rack Installation Instructions
IBM Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following:
More informationIBM Systems. Quick start guide for IBM System p5 505 ( )
IBM Systems Quick start guide for IBM System p5 505 (9115-505) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up
More informationReplacing the Gateway M275 Keyboard
Replacing the Gateway M275 Keyboard This package includes a replacement keyboard for your Gateway M275 notebook and these printed instructions. Tools you need You need a small Phillips screwdriver and
More informationTyler - Middle Mount For Bell 407, 206 & 206L Series Helicopters FAA STC # SH3246NM
MIDDLE MOUNT 407 / JET RANGER / LONG RANGER INSTALLATION MANUAL Tyler - Middle Mount For Bell 407, 206 & 206L Series Helicopters FAA STC # SH3246NM PLEASE RETURN THIS MANUAL WITH EQUIPMENT This manual
More informationTitan Media Cart. Installation and Operation Manual
Titan Media Cart Installation and Operation Manual Table of Contents INTRODUCTION SERVICE AND SUPPORT... 1 PRODUCT RETURNS... 1 UNPACKING... 1 TITAN SINGLE MEDIA CART... 2 TITAN DUAL MEDIA CART... 2 BEFORE
More informationSAMi Installation Instructions
SAMi Installation Instructions Unpack the camera. Leave the clear plastic protective film on until after the camera is installed as it is easy to scratch the lens. For the initial setup you need to connect
More informationCIB 3097 ESD Suppression Kit
CIB 3097 ESD Suppression Kit CIB 3097 Comcode 105-215-321 Issue 1 CIB 3097 ESD Suppression Kit When installed in a voice terminal s ZH802A or ZH802B module that is experiencing Electro-Static Discharge
More informationQuick Start. This document describes how to install the Juniper Networks PTX5000 Packet Transport
PTX5000 Packet Transport Router Quick Start September 2017 Part Number: 530-066788 Revision 01 This document describes how to install the Juniper Networks PTX5000 Packet Transport Router. Contents Quick
More informationMO-SYS L 40-3rd Axis Quick Set-up Guide
MO-SYS L 40-3rd Axis Quick Set-up Guide WILLIAM F. WHITE INTERNATIONAL INC. Manual Version 1.0 Questions or concerns, please contact Michael Darby 416.707.1549, mdarby@gmail.com MO-SYS L 40 3rd Axis Intro
More informationThank you for purchasing one of our products. I hope that the Tech Tub 2
FTT1000 FTT1000-USB Tech Tub 2-10 Device Setup Assembly Guide FTT1000_FTT1000-USB_2017_D Check out our other products online at www.copernicused.com For assistance, please contact us: 1-800-267-8494 Email
More informationQuick start guide for i5 520 ( or )
Quick start guide for i5 520 (9405-520 or 9406-520) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up a standard
More informationPT Teleprompter
Features you need, Prices you want. PT3000 15 Teleprompter User Guide 3903 Stoney Brook Dr. Houston TX 77063 Tel: 1.713.272.8822 Fax: 1.713.995.4994 www. support@ 2009 ikan Corporation. All right reserved.
More informationAssembly Instructions
Assembly Instructions Flat Screen Garage End User & IT Computer Cable Management May 2013 nylon zip-tie #2 (for computer wires) rear-access beam door (open) Figure 1 nylon zip-tie #1 (for #1 motor control
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationSECTION 5 -- EQUIPMENT LAYOUT & EQUIPMENT ENVIRONMENTS
SECTION 5 -- EQUIPMENT LAYOUT & EQUIPMENT ENVIRONMENTS CONTENTS PAGE 1. GENERAL... 5-1 1.1. Introduction... 5-1 1.2. Equipment Layout Requirements... 5-1 2. EQUIPMENT FRAMES... 5-2 2.1. Introduction...
More information25 Sport Scope Instruction Manual
25 Sport Scope Instruction Manual Dear Customer, We appreciate your business and value your support for our product. At Sport Scope, we strive to provide our customers with quality, easy to use, and affordable
More informationTASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS
TASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions. Save these instructions. The most up-to-date warnings and instructions are available at www.taser.com
More informationQuick start guide for p5 520 ( )
Quick start guide for p5 520 (9111-520) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up a standard system. Users
More informationRef. No. Part Name & Description Part No. Quantity Remarks
- R _ Ref. No. Part Name & Description Part No. Quantity Remarks A -1 Nozzle Housing AC01ABCCZGU4 1 Includes A-26 Packing A - 2 Window AC21HAFV200 1 A - 3 Shaft (Plastic) AMC25S-V00 1 A - 4 Furniture Guard
More informationInstallation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL)
Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL) Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the paint)
More information1 AM-167/202/242/282/322 Parts Manual. Table Of Contents
AM-167/202/242/282/322 Parts Manual Table Of Contents Mower Beam with Bearings...2 Mower Beam with Bearings...4 Cutting Discs...6 Main Gearbox...8 V-Belt Pulley...10 Headstock...12 Carrier Beam...14 V-Belt
More informationDesign and Manufacture of Video Pipeline Inspection Systems A Full Service Company
Design and Manufacture of Video Pipeline Inspection Systems A Full Service Company www.rstechserv.com Omni Star LED Pan and Tilt Zoom Color Camera Modell 10-1660 INSTALLATION MANUAL Made in USA IMPORTANT
More informationLumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light
LumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light Assembly and Operation Instructions Thank you for investing in this premium Platinum Health product. Please carefully follow the assembly
More informationLiebert XDA Air Flow Enhancer. User Manual
Liebert XDA Air Flow Enhancer User Manual Technical Support Site If you encounter any installation or operational issues with your product, check the pertinent section of this manual to see if the issue
More informationASSET LGA1366 Top-side Probe
ASSET LGA1366 Top-side Probe (Manual version 1.1) For gaining test access to the debug port of Intel processors that are designed for use in LGA1366 Sockets (Socket B). These include the Intel Core i7
More informationM-2300-S Mustang GT 14 Brake Upgrade Kit INSTRUCTION SHEET
Please contact the Techline for the most current instruction information (800) FORD788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: This kit is designed for use
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More information(120V) (100V / OBSOLETE)
Aquamatic Selectric PARTS LIST Advance MODELS 0(0V) 0(00V / OBSOLETE) This parts list is for machines after serial number 0 / revised /0 Form Number 0 revised /00 FORM NO. 0 TABLE OF CONTENTS DESCRIPTION
More informationGPIB-232CT-A IBCL EPROM Installation Guide
NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationPIX 520. PIX 520 Product Overview CHAPTER
CHAPTER 5 PIX 520 This chapter guides you through the installation of the PIX 520, and includes the following sections: PIX 520 Product Overview, page 5-1 Installing the PIX 520, page 5-4 PIX 520 Feature
More informationTelescoping Mast Mount A typical PaR manipulator accesses a work area using PaR s bridge, trolley and telescoping mast system.
M A N I P U L AT O R S Continuous Shoulder Rotation Thanks to a proven shoulder rotate and slip ring design, the manipulator can be infinitely rotated in either the clockwise or counterclockwise directions.
More informationEPX2555 Advantage Series Piston Pump
EPX Advantage Series Piston Pump Owner s Manual Do not use this equipment before reading this manual! Model Numbers: 00 Upright Cart Complete 00 Low Boy Cart Complete NOTE: This manual contains important
More informationKRONOS 6752 LIFT DESK
KRONOS 6752 OWNER S MANUAL Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register
More informationDIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL
DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL Version 2.1 June 4, 2013 0 Table of Contents Low Profile Pan Tilt Kit Description... 3 Low Profile Pan Tilt Unit Basic Operation... 4 Mounting
More informationM-2300-ZX Focus SVT Brake Conversion Kit INSTRUCTION SHEET
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: This kit is designed
More informationPIX 515/515E. PIX 515/515E Product Overview CHAPTER
CHAPTER 4 PIX 515/515E This chapter describes how to install the PIX 515/515E, and includes the following sections: PIX 515/515E Product Overview Installing a PIX 515/515E PIX 515/515E Feature Licenses
More informationProLiant ML350 Tower-to-Rack Conversion Guide. First Edition (September 2000) Part Number Compaq Computer Corporation
ProLiant ML350 Tower-to-Rack Conversion Guide First Edition (September 2000) Part Number 201346-001 Compaq Computer Corporation Notice 2000 Compaq Computer Corporation Compaq, ProLiant, and the Compaq
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationImprove the appearance and accessibility of your rack
Vertical Cable Organizer with D-Ring Hooks - 0U - 3 ft. StarTech ID: CMVER20UD This 3-foot vertical cable manager gives you a simple and space-efficient way to organize the cables in your server rack.
More informationInstallation guide. for Cisco TelePresence MX700 Dual Camera on a free standing floor stand or a floor stand secured to the wall
Installation guide for Cisco TelePresence MX700 Dual Camera on a free standing floor stand or a floor stand secured to the wall http://www.cisco.com/go/mx-docs This guide covers the floor stand mounted
More informationFloor Standing Pedestal
2336 K052 Floor Standing Pedestal Kit Instructions Issue C Revision Record Issue Date Remarks A Feb 20021 First issue B June 2007 Added pedestal floor bolting procedure C Mar 2011 Added Universal Mounting
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationProjectors 6 and 7 Ruggedized Lens Components Installation Manual
Projectors 6 and 7 Ruggedized Lens Components Installation Manual This document includes the procedures required to install the ruggedized lens components for Projectors 6 & 7 (Matrix 4000 M / 38-DSP104-09).
More informationSTEP-BY-STEP INSTRUCTIONS FOR BUILDING AN AUTOCOLLIMATOR. TECHSPEC Optical Cage System
STEP-BY-STEP INSTRUCTIONS FOR BUILDING AN AUTOCOLLIMATOR TECHSPEC Optical Cage System INTRODUCTION 2 What is an autocollimator? The Autocollimator is a precision instrument composed of an achromatic objective,
More informationCIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007)
CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) CIB 3047 Comcode 845-659-325 Issue 1 CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) This
More informationReplacing the Billboard Router
Replacing the Billboard Router (PN 1109503001SP) The billboard router creates a firewall protected VPN (Virtual Private Network) inside the deluxe remote control cabinet. The router splits the incoming
More informationCisco TelePresence VX Clinical Assistant TM
Cisco TelePresence VX Clinical Assistant TM ACCESSORIES INSTALLATION GUIDE Drawer Module, PC Cabinet Module, PC Shelf, and Storage Pods...2 Laptop Shelf...3 Scope Hooks, WAP Mount, and Splash Cover...4
More informationAP65 Access Point. The Aruba AP65 Access Point is a compact Tri-Band Wireless Unit supporting the a, b and g WiFi standards.
AP65 Access Point The Aruba AP65 Access Point is a compact 802.11 Tri-Band Wireless Unit supporting the 801.11a, 801.11b and 801.11g WiFi standards. The AP65 is designed to be directly mounted on a standard
More informationInstallation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays
Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays Model: DS-VWT955-2X2 EXTENSION COLUMN (SOLD SEPARATELY) COMPATIBILITY Display width must be a minimum of 36"
More informationGround Power Modules. And Accessories For Healthcare Facilities. Technical Bulletin NAE /
2 Ground Power Modules And Accessories For Healthcare Facilities Technical Bulletin NAE2092320 / 10.2011 Ground Power Modules Hospital grade outlet modules Introduction BENDER series GPM ground and power
More informationAP-120 Series AP Mounting Kit
AP-120 Series AP Mounting Kit Installation Guide The AP-120 series mounting kit provides additional mounting options for the AP-120 series wireless access points. The mounting kit includes the following
More informationAccessory Guide Indoor AP Accessories
Indoor AP Accessories INDOOR SKU Compatible Products Description Kit Contents 902-0120-0000 R720 R710 R700* R600* R610* R500* R510* R310 * fits AP, but does not support padlock security Multipurpose mounting
More informationPlanar Model A480-PL Professional Grade Home Cinema Conversion Lens System
AKPro system with ATH1 transport shown Planar Model A480-PL Professional Grade Home Cinema Conversion Lens System USER MANUAL AND INSTALLATION GUIDE Including the UH480 Lens, ATH1 Transport and AKPro Projector
More informationT R A N S F O R M I N G T E C H N O L O G I E S, L L C O U T S T A N D I N G A L T E R N A T I V E S I N S T A T I C C O N T R O L
T R A N S F O R M I N G T E C H N O L O G I E S, L L C O U T S T A N D I N G A L T E R N A T I V E S I N S T A T I C C O N T R O L Ohm Metrics Combonation Wrist Strap & Footwear Tester Model PDT700 Instruction
More informationAssembly Instructions for the KA Electronics Elliptic Equalizer
Assembly Instructions for the KA Electronics Elliptic Equalizer Install IC sockets Elliptic Equalizer PC Board Stuffing Guide Place the PC Board on the work bench silkscreen side face up. Place twelve
More informationEaton LCD Lift Flat Panel Display System. Installation Guide
Eaton LCD Lift Flat Panel Display System Eaton LCD Lift Flat Panel Display System Installation Guide Copyright 2011 Eaton Corporation, Worcester, MA, USA. All rights reserved. Information in this document
More informationAccessory Guide ZoneFlex Indoor AP Accessories
ZoneFlex Indoor AP Accessories INDOOR SKU Compatible Products Description Kit Contents 902-0120-0000 ZoneFlex R720 ZoneFlex R710 ZoneFlex R700* ZoneFlex R600* ZoneFlex R610* ZoneFlex R500* ZoneFlex R510*
More informationUse the instructions in this section for loading roll or fanfold media in the appropriate print mode for your needs.
32 Load the Media Load the Media Use the instructions in this section for loading roll or fanfold media in the appropriate print mode for your needs. Caution While performing any tasks near an open printhead,
More informationInstallation and Maintenance
CHAPTER 4 Installation and Maintenance Revised: April 19, 2010, Introduction This chapter explains how to install a SCE 1000 platform in a rack or in a general tabletop or workbench installation. Additionally,
More informationA TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address
Requirements A TCP/IP network CAT 5 cable If the network is faster than 10baseT a switching hub will be needed Static IP address Power Up A Reader with an Ethernet adaptor installed and the network cable
More informationPracticeWire Installation Manual
PracticeWire Installation Manual Version 5.0 August 28 th, 2013 PCM Help Desk 1-877-233-9114 Page 1 Table of Contents System Overview 3 Tool List 4 Installation Guide Site Notification 5 Install Universal
More informationMoving-Minds.com Treadmill Desk Operation
LifeSpan Treadmill Desk - Owner s Manual Models DT-5/DT-7 Desk Assembly DT-5 Desk........................................................................................ Assembly Instructions..........................................................................
More informationTHE ISAAC NEWTON GROUP OF TELESCOPES
THE ISAAC NEWTON GROUP OF TELESCOPES INSTRUMENT CHANGE CHECKLIST PRIME FOCUS IMAGING PLATFORM (PFIP) USING THE MOSAIC CAMERA WITH UDAS Revision : 2.2 Description : Location : Weight : CCD Wide Field Imaging
More informationFurther Information can be found at
Below is a step by step guide to assembling the Hurricane-Rig. Remember that this is a precision optical instrument. Excessive force can bend critical parts. If treated well it should give many years of
More informationT R A N S F O R M I N G T E C H N O L O G I E S, L L C O U T S T A N D I N G A L T E R N A T I V E S I N S T A T I C C O N T R O L
T R A N S F O R M I N G T E C H N O L O G I E S, L L C O U T S T A N D I N G A L T E R N A T I V E S I N S T A T I C C O N T R O L Ohm Metrics Wrist Strap & Footwear Combination Tester GTS600 Instruction
More informationPAU Cam instructions. Release Draft/Final: Version 1.0 Date: 30 th December Cristobal Padilla, Otger Ballester, Jürg Rey.
Release Draft/Final: Version 1.0 Date: 30 th December 2016 Author(s): Owner: Client: Document Number: Cristobal Padilla, Otger Ballester, Jürg Rey Don Carlos Abrams Isaac Newton Group of Telescopes TBD
More informationPrepulse Inhibition (PPI) Boxes
Prepulse Inhibition (PPI) Boxes Always calibrate the PPI boxes prior to testing on each day See print manual for more information Calibration: 1) Turn on the boxes by switching on the surge protector on
More informationQuick Reference Guide to the Canon I MiniDV Camera BE CAREFUL WHEN INSERTING AND EJECTING TAPES FROM THE CAMERA.
mm medialab Quick Reference Guide to the Canon I MiniDV Camera BE CAREFUL WHEN INSERTING AND EJECTING TAPES FROM THE CAMERA. FOLLOW ALL LABELS ON THE CAMERA ITSELF AND THESE DIRECTIONS. CAMERA MODE / VCR
More information