HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS Low Fit and Lever Type Connector
|
|
- Avice Weaver
- 5 years ago
- Views:
Transcription
1 B 47 HOW TO INSTALL AND REMOVE SPECIAL CONNECTORS Low Fit and Type Connector [Case 1] (1) Push the place indicated by the arrow. (2) The lock is released and lever is lifted up. (3) Lift the lever up until it stops. an (4) Cut the connection of the connector. 2. Connect the connector (1) Connect the connector in the condition that the lever is fully lifted up. HINT: If the lever is locked at the lower position, follow the procedure [Case 1]. (1) to (3) and lift the lever up fully. 57
2 B 48 (2) Hold the connector to prevent it from slip off and push it down until you hear a click to lock it. is not locked (3) Confirm that the lever is securely locked. [Case 2] (1) Hold the area indicated by the arrow in the illustration (2) The lock is released and the lever is lifted up. (3) Lift the lever up fully. (4) Cut the connection of the connector. 58
3 B Connect the connector (1) Connect the connector in the condition that the lever is fully lifted up. (2) Hold the connector to prevent it from slip off and push it down until you hear a click to lock it. is not locked (3) Confirm that the lever is securely locked. [Case 3] (1) Pick the part indicated in the illustration by fingers. (2) The lock is released and the lever is lifted up. (3) Lift the lever up fully. 59
4 B 50 (4) Cut the connection of the connector. 2. Connect the connector (1) Connect the connector in the condition that the lever is fully lifted up. HINT: If the lever is locked at the lower position, follow the procedure [Case 3]. (1) to (3) and lift the lever up fully. (2) Hold the connector to prevent it from slip off and push it down until you hear a click to lock it. (3) Confirm that the lever is securely fitted is not locked 60
5 B 51 Coil spring Pin Convex part Double locking device pin The connector with secondary locking device 1. Area used Wire harness for SRS airbag deployment Primary locking device Lock 2. Cut the connection of the connector. (1) Release the double locking. (2) Release the primary locking and separate the connector. 3. Connect the connector (1) Install the primary locking device and connect the connector. Lock (2) Install the double locking device. The double locking device can not be installed unless the primary locking device is installed. 61
6 B 52 Connector fixed by bolts 1. Area used Engine control computer harness Connector A Connector B 2. Cut the connection of the connector. (1) Remove the connector A. (2) Loose the bolt using a tool like driver until the connector B can be removed by hand and separate the connector. HINT: If the bolt can not be removed, roll it while pulling forward. Lass than 1mm Connector B Bolt Connector A 3. Connection of the connector (1) Temporarily fit the connector B. (2) Tighten the bolt by using tool like driver and fit the connector B completely. Tighten the bolt until feeling it lighter. Then confirm that the width of chink of the connector B is less than 1mm. The bolt can be rolled after it is fitted. If the impact wrench is used, do not let it rolling more than three seconds. (The housing may be deformed by generated heat) Be sure and connect the connector B straight. Do not incline it while connecting. (3) Connect the connector A. Cross section of the bolt 62
7 Hold back rib to pull connector B 53 (1) Push down on locking arm to unlock. Then hold the back ribs of connector to remove connector. Locking Arm (2) Cut the Connection of the connector. 2. Connect the Connector back ribs (1) Align the direction of locking feature in same direction and mate the connector holding the back ribs in straight direction. (2) Insert it until a lock securely locks, and pull the connector lightly after the insertion, and confirm that a lock is enabled. 63
Instruction Sheet AND 105 POSITION CONNECTORS FOR 196 WAYS HEADER.
91 AND 105 POSITION CONNECTORS FOR 196 WAYS HEADER. A RELEASE YH MA/ HG CHO 11-MAR-2011 REV. DESCRIPTION DR/CHK DATE Rev A Page 1 of 16 Index A. OBJECT p.3 B. SCOPE p.3 C. PACKAGING OF THE CONNECTORS p.4
More informationReplacing the SATA PCI Controller Card
Replacing the internal controller PCI card may be performed by a single administrator; no tools are necessary. Caution There are static-sensitive electronics inside the unit. Before you handle any parts,
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationCM10-SPxxS-x-D Plug Connector (Crimp type) Cable Assembly Manual
CM10-SPxxS-x-D Plug Connector (Crimp type) Cable Assembly Manual Date of Issue: July,3, 2007 Manual No. TC-0583 Revision Date Revision No. A 2007/07/03 New Issue DDK Ltd. 2ND Production eng. dept. assembly
More informationReplacement Instructions
apple Xserve Memory Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Online instructions
More informationWhen you are ready to build your computer you will have the following materials to work with.
Copyright 2009 BOSMA Enterprises Chapter 3 Putting the Computer Together When you are ready to build your computer you will have the following materials to work with. 1. One motherboard. 2. One ribbon
More informationAllen-Bradley Drives. Instructions. (For 6180 Industrial Computers)
Instructions (For 6180 Industrial Computers) This document describes how to remove or install a Pentium processor in the 6180 Industrial Computer. Processor specifications are also provided. The processor
More informationCM10-SP S- -D Plug Connector (Crimp type) Cable Assembly Manual
CM10-SP S- -D Plug Connector (Crimp type) Cable Assembly Manual DDK Ltd. 2ND Production engineering department assembly group 14 Matsuyama-cho, Moka-shi, Tochigi TEL : 0285-82-4463 Date of Issue: July
More informationCentral Processing Unit (CPU) Replacement
Central Processing Unit (CPU) Replacement Written By: Dozuki System 2018 gunnerautomotive.dozuki.com/ Page 1 of 17 INTRODUCTION OdXAkjljPNWbtqrS.pdf TOOLS: test (1) 7.5 " Machinist's Scale (1) 2018 gunnerautomotive.dozuki.com/
More informationShop Fox Fence Kit Installation Instructions:
Shop Fox Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Shop Fox Classic Fence. Accurate Technology manufactures kits for other saw fences
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationIncluded Items Not Shown:
PN 09 HP Illuminator ssy Olympus HS Installation Instructions - Nanodyne Illuminator for Olympus HS Microscope Figure. Parts included in Olympus HS Illuminator System. Included Items Not Shown: PN 057.5mm
More informationWritten By: John Sutton
Replacing the fan on your HP g7-2275 dx. Written By: John Sutton ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION Laptop cooking your lap? This guide will walk you through replacing your fan.
More informationA-MOD DESKTOP OWNER S MANUAL
A-MOD DESKTOP OWNER S MANUAL GOJOTTO.COM 877-55-6886 IMPORTANT NOTICE: Please take a few minutes to read through this Owner s Manual before using the product to ensure that your A-MOD Desktop will be operated
More informationFOR PC BOARD TO FLAT CABLE
AXM FOR PC BOARD TO FLAT CABLE MIL CONNECTORS (AXM) Density mounting Long lever type Short lever type Compliance with RoHS Directive FEATURES 1. High density mounting is possible. Even with mounting right
More informationDell Latitude C800 Service Manual
Dell Latitude C800 Service Manual Dell Latitude C800 Service Manual Before You Begin Preparing to Work Inside the Computer Recommended Tools Screw Identification Removing and Replacing Parts System Components
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationOracle <Insert Picture Here>
Slide 1 Oracle Slide 2 WZT-6509 version B Sun Fire Nehalem and Westmere Rack-Mount Server Installation and Replacement Welcome to the installation and replacement
More information3D SYSTEMS University CubeX 3D Printer
3D SYSTEMS University CubeX 3D Printer Lesson Leveling the Print Pad and Print Tips, Setting the Z-Gap Revision date: 10/22/13 1 1 2016 年 6 月 14 日 Objectives After completing this lesson you will: Be able
More informationInstalling 6 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing 6 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Overview...5 Installing the
More informationDell Storage MD1400 Enclosures Hardware Owner's Manual
Dell Storage MD1400 Enclosures Hardware Owner's Manual Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates
More informationMotorola Moto Z2 Play Audio Jack Replacement
Motorola Moto Z2 Play Audio Jack Replacement How to replace your Moto Z2 Play's audio jack with this guide if you can't hear with headphone or if there are scratching noises. Written By: mitch miller ifixit
More informationALLDATA Online Saab 9-3 (9400) L4-2.0L Turbo (B205) Saab 9-3 ( Saab 9-3 (9400) 4D/5D; Saab 9-3 (9400) CV
Page 1 of 7 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Saab 9-3 (9400) L4-2.0L Turbo (B205) Conversion Calculator Vehicle
More informationAttaching DX Encoders to your Majestic Carriage
Attaching DX Encoders to your Majestic Carriage Encoders are the white wheels that you need to have on your carriage in order for the stitch regulation to work. Encoders detect the movement of the machine
More informationINTRODUCTION TO MECHANICAL ASSEMBLY (DVD-46C)
This test consists of twenty multiple-choice questions. All questions are from the video: Introduction to Mechanical Assembly. Each question has only one most correct answer. Circle the letter corresponding
More informationMale header, 100% protected against mismating, (1 x 1) mm straight solder pins Pin spacing 3.5 mm 3.81 mm. light gray <_ 8,5_> 3,5 1x1 <_ 9,3_>
96 Male Headers with Solder Pins; Double-Deck Male Headers with Solder Pins, Pin Spacing 3.5 mm and 3.81 mm 160 V/.5 kv/ 300 V, 10 A U 10 A 300 V, 10 A 160 V/.5 kv/ 300 V, 10 A U 10 A 300 V, 10 A 160 V/.5
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationSilent Sentinel Solar Powered Advanced Warning Vehicle Mounted. Arrow Panels. Installation, Operation and Maintenance Manual (P/N )
Silent Sentinel Solar Powered Advanced Warning Vehicle Mounted Arrow Panels Installation, Operation and Maintenance Manual (P/N 550-125-100) Harness Harness the the Power of of the Sun! 7620 Cetronia Road,
More informationZ-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly
Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.
More informationREAD INSTRUCTIONS THOROUGHLY BEFORE OPERATING
OPERATING INSTRUCTIONS 350B Back Buddy II READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING 800.223.4540 3451 S. 40th Street Phoenix, AZ 85040 602.437.5020 www.tsissg.com info@tsissg.com Fax 602.437.5025 March
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationKM-4800w. Installation Guide
KM-4800w Installation Guide TABLE OF CONTENTS page 1 Installation Requirements 2 2 Unpacking 3 2. 1 Unpacking 3 2. 2 Confirmation of Accessories 5 3 Leveling the Machine 7 4 Setup of the Roll Deck 9 5
More information1.27mm Pitch Multi-function Two Piece Connector
1.27mm Pitch Multi-function Two Piece Connector FX2 Series Stacking connection (Stack height: 12~16mm) 12mm~16mm Features 1. Various connection with various product line 2. Easy One-Touch Operation Stacking
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS AUDIO UNIT P/N 08A70-MJN-A00 CTX1300/D MII 14925 Issue Date April 2014 PARTS LIST (11) (8) (2) TOOLS AND SUPPLIES REQUIRED Socket (10 mm)
More informationPLEASE NOTE: These instructions are intended to be used by a person with average mechanical and electrical skills.
ClassicLEDs is please to present their latest line in Corvette LEDs. This covers the 1975 thru 1979 Corvette. This systems does not include the Corvette... PLEASE NOTE: These instructions are intended
More informationWEASEL N/B MAINTENANCE
2. System Assembly & Disassembly 2.1 System View 2.1.1 Front View ❶ Microphone Connector ❷ Audio Input Connector ❸ Audio Output Connector ❹ Top Cover Latch ❹ ❶ ❸ ❷ 2.1.2 Left-Side View ❶ VGA Port ❷ S-Video
More informationHARMONi G3. Quick Start Guide for HARMONi G3. imac Processor/FireWire Upgrade
HARMONi G3 imac Processor/FireWire Upgrade imac and Operating System Compatibility The HARMONi G3 imac processor/firewire upgrade is compatible only with imac 233, 266, and 333 MHz models (Revisions A-D);
More informationPARTS CATALOGUE / TECHNICAL GUIDE Cal. S149A
PARTS CATALOGUE / TECHNICAL GUIDE [SPECIFICATIONS] Item Module Cal. No. S149A (x 0.30) Module size Outside diameter 198.1 mm between 6 o clock and 12 o clock sides 81.6 mm between 3 o clock and 9 o clock
More informationBiesemeyer Fence Kit Installation Instructions:
Biesemeyer Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Biesemeyer Commercial Fence. Accurate Technology manufactures kits for other saw
More informationMAESTRO Cochlear Implant System. QuickGuide. RONDO Audio Processor
MAESTRO Cochlear Implant System QuickGuide RONDO Audio Processor Getting to Know the RONDO The parts and functions Control Unit: The control unit is just like a tiny computer. Inside, an electronic chip
More informationUser support guide SNC Label printing equipment
User support guide SNC Label printing equipment 1 P a g e Table of Contents PM43 INTERMEC LABEL PRINTER... 3 1. BASIC SETTINGS... 3 1.1. Printer front panel settings... 3 2. TROUBLESHOOTING TIPS... 3 2.1.
More informationHDR TM K HOIST DRUM ROTATION INDICATOR KIT
HDR TM K240260 HOIST DRUM ROTATION INDICATOR KIT INSTALLATION MANUAL HDR TM K240260 HOIST DRUM ROTATION INDICATOR KIT 1 of 8 PN W240200 REV A 11/01/01 HDR TM K240260 HOIST DRUM ROTATION INDICATOR KIT TABLE
More informationVeNICE 2002 VeNICE 2002-PRO Range Rover L Bluetooth Audio Input Module
VeNICE 2002 VeNICE 2002-PRO Range Rover L322 2002-2005 Bluetooth Audio Input Module Thank you and congratulations for the purchase of the L322 VeNICE Bluetooth module! We are urged to remind you that any
More informationCARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS
CARD PRINTER PRINTHEAD REPLACEMENT INSTRUCTIONS CAUTION: The discharge of electrostatic energy that accumulates on the surface of the human body or other surfaces can damage or destroy the printhead. Please
More informationOlympus BX43_46 Installation Instruction (OEM Adjust) 4
Olympus X_6 Installation Instruction (OEM djust) If you are not an experienced repair tech please consider the alternate (easy install) version dditional Items Included ut Not Shown: PN 07 Olympus X Illuminator
More informationAPPLICATION SPECIFICATION
MOLEX MINI 50 0.50MM CONNECTOR SYSTEM PPLICTION SPECIFICTION 1.0 SCOPE THIS PROCEDURE PPLIES TO LL PRT NUMBERS IN THE 34791, 34792, ND 34793 SERIES Table of Contents 1: Product Scope 2: Product Description
More informationUpgrading the programmer supply unit of the BeeProg+/BeeProg2 programmer
Upgrading the 50-0033 programmer supply unit of the BeeProg+/BeeProg2 programmer How-Do-It Manual December 2012 BeeProgX_50-0033_PSU1_upgrade_manual, version 1.31 page 1 Introduction This how-do-it manual
More informationDOWNLOADING THE APP FOR APPLE PHONES: DOWNLOADING THE APP FOR ANDROID PHONES: For Android Phones go to Google Play or the Android Store.
DOWNLOADING THE APP FOR APPLE PHONES: DOWNLOADING THE APP FOR ANDROID PHONES: For Android Phones go to Google Play or the Android Store. For Apple Phones go to the app store and click GET. Make sure your
More informationJLTX Lever and Joystick Replacement Instructions
JLTX Lever and Joystick Replacement Instructions WARNING THE INCORRECT INSTALLATION OF A LEVER OR JOYSTICK CAN CAUSE AN EQUIPMENT MALFUNCTION FAILURE TO FOLLOW THIS PROCEDURE CAREFULLY COULD RESULT IN
More informationBack Tilt Sensor Repair Kit [ ]
Back Tilt Sensor Repair Kit [002-1377-00] Components: Potted Tilt Sensor & Harness...1 Cable Ties...8 Step 1: Position chair. A) Press chair up control button to raise chair seat approximately 26-28 above
More informationStudio adaptor SA Operation manual <Tentative>
Studio adaptor SA-1000 Operation manual Rear panel of the SA-1000 operation CA-HF1000 RET1/2 SEL switch Extender LED Light when lens Extender x0.8 is on POWER Lamp Light when camera Head power
More informationInstallation Instructions
Installation Instructions Page 1 of 18 November 2007 Communication, Hands-Free Version 6.0 Accessory Development These Installation Instructions supersede all previous versions. SUBJECT PHONE DOCKING CRADLE
More informationSetup Guide. Confirming the Installation Space. Installation space (W x D x H) 70.5 x 66.3 x 61.5 inches (1790 x 1684 x 1560 mm) 23.
Introductory Information Setup Guide ENGLISH Read this manual before attempting to operate the printer. Keep this manual in a handy location for future reference. Caution Instructions in this Setup Guide
More informationNintendo DS Lite Rear Display Bezel Replacement
Nintendo DS Lite Rear Display Bezel Replacement Replacement of the Nintendo DS Lite rear display bezel. Written By: Matt Newsom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Replace the rear
More informationPositive Mate Connection System
Introduction High Current Flow with Low Insertion Force Product Features All Positive Mate housings include a secondary contact retention feature Polarization is provided Rounded corners on housings prevent
More informationimac Intel 27" EMC 2429 SSD Dual Drive
imac Intel 27" EMC 2429 SSD Dual Drive Installation Install the dual hard drive kit in an imac Intel 27" EMC 2429. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 22 INTRODUCTION This guide
More informationUltraloq UL3 Series Fingerprint and Touchscreen Smart Lock
Ultraloq UL3 Series Fingerprint and Touchscreen Smart Lock Installation Instructions ( V1.4 ) Welcome Installation Video Please watch our easy step by step installation video before attempting to install
More informationKeypad Lock. Operation and Service Manual. Order parts online
Keypad Lock Order parts online www.follettice.com Operation and Service Manual 801 Church Lane Easton, PA 18040, USA Toll free (800) 523-9361 (610) 252-7301 Fax (610) 250-0696 www.follettice.com 00163345R00
More information1 Installing the VG4-A-ARMPLATE
VG4 24 VAC Mounting Plate Installing the VG4-A-ARMPLATE en 1 1 Installing the VG4-A-ARMPLATE This addendum provides supplemental information for the AutoDome Modular Camera System Installation Manual.
More information2 x Dynamic Arms on 135 Post with C-Clamp
Installation Guide AWMS-2-D13-C 2 x Dynamic Arms on 135 Post with C-Clamp COMPONENT CHECKLIST RANGE A AWM-LC Post Clamp B AWM-AD Dynamic Arm (x2) C AWM-P13 135 Post D AWM-FC C-Clamp CONTENTS C-Clamp Page
More informationww.battery-adapter.com
Removing and replacing an FRU Lenovo G470/G475/G570/G575 This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general
More informationField Service Guide Supplement for the NS 7000/030
AUSPEX Field Service Guide Supplement for the NS 7000/030 Copyright 1998, Auspex Systems, Inc. All rights reserved. Part number 850550. Important Notice The installation or replacement procedures in this
More informationInstallation Manual for B8300 and Its Peripheral Devices
Installation Manual for B8300 and Its Peripheral Devices Finishing device Duplex/bypass device Finishing device To install the devices efficiently, follow the procedure below. Some peripheral devices may
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationModel 2704 Parts List * = Standard Equipment 〇 = Circuit Diagram
2704 11-05 99 98 97 82 88 89 83 84 85 86 87 101 103 100 106 81 71 105 104 73 74 75 76 77 78 80 79 57 62 58 56 63 65 66 67 68 64 69 70 59 60 61 31 30 29 32 34 35 41 40 42 36 37 38 39 43 4445 46 21 22 20
More informationNavigation interface for Jeep GC 5 RA2 NTV-KIT581
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Jeep GC Navigation interface for Jeep GC 5 RA2 NTV-KIT581 NNG-JEEP GC Kit Content 5 1 6 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8.
More informationExtra Large Full Motion TV Mount for Televisions
8008981 TV Size Range: 47 ~ 84 Maximum Weight Capacity: 60 kg/132 lbs Maximum Mounting Pattern: 800 mm x 600 mm (31.4 x 23.6 ) Distance to the Wall: 5.5-45 cm Extra Large Full Motion TV Mount for 47-84
More informationCommon Precautions for XF Connectors
Common Precautions for XF Connectors Safety Precautions Precautions for Correct Use (4) Do not apply the soldering iron to any parts of the connector other than the mount attachments. Doing so may cause
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationOlympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4
Olympus X and X6 Installation Instruction for Microscope End Users (easy install version) PN 07 Olympus X_6 Illuminator ssy dditional Items Included ut Not Shown: PN 077 Hex Key mm PN 060 Hex Key mm M
More information1.27mm Pitch Multi-function Two Piece Connector
1.27mm Pitch Multi-function Two Piece Connector FX2 Series Stacking connection (Stack height: 12~16mm) 12mm~16mm Horizontal Connection Vertical Connection 25mm Features 1. Various connection with various
More informationDell PowerEdge R940. Upgrading the dual processor to quad processor system
Dell PowerEdge R940 Upgrading the dual processor to quad processor system Copyright 2017 Dell Inc. or its subsidiaries. All rights reserved. 2017-10 Part Number - 7WCG8 Rev. A00 Upgrading the dual processor
More informationFigure 4-29 Removing the CPU compartment cover
4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment
More informationIoline CrystalPress. Quick Start Guide
Ioline CrystalPress Quick Start Guide The Quick Start Guide is intended to help a new user of the Ioline CrystalPress get everything setup and running quickly. Please note that there are important notices,
More informationStealthyPro Instructions
StealthyPro Instructions 3-point Shooter Mode / Handheld Mode / Monopod Mode Place the black piece between the handle and the silver ring (as pictured). Stabilizer Mode In stabilizer mode, thread the handle
More informationInstallation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio
Introduction The following instruction procedure is for the RGB interface to a GM 05 Nav Radio as part of the Webasto Product NAVCam Back-up Camera (VCP-0000220). In addition, an installer will need to
More informationZ Spindle. Revision 1.2. Copyright Newing-Hall, Inc Monroe Street. Toledo, Ohio, NH Part # Last Update July 2003
Z Spindle Revision 1.2 Copyright 1998-1999 Newing-Hall, Inc. 2019 Monroe Street Toledo, Ohio, 43624 NH Part #2511013 Last Update July 2003 This manual is subject to change without notice. Table Of Contents
More informationRAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100800 1 Cable Installation Kit 2000901-1 1 Dielectric Grease 2002872
More informationNov. 07, 2013 p. 5 - changed the B axis unit value to from Changed by Randy per Frank s request.
Correction notes Nov. 07, 2013 p. 5 - changed the B axis unit value to 45.1389 from 40.0000. Changed by Randy per Frank s request. Jan. 22, 2018 p. 5 - changed the B axis unit value and corresponding picture
More informationM40 Microscope User s Manual
M40 Microscope User s Manual for M40 and M40RT Microscope Components: Trinocular Port Eyepieces Beam Splitter Field Diaphragm Adjustment Aperture Diaphragm Adjustment Filter Slots Analyzer Polarizer Hex
More informationToshiba Satellite A210 Motherboard
Toshiba Satellite A210 Motherboard Replacement In this guide you will learn how to properly remove the Motherboard. Written By: Devin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Before
More informationDell Latitude C800 SERVICE MANUAL. support.dell.com
Dell Latitude C800 SERVICE MANUAL www.dell.com support.dell.com Dell Latitude C800 SERVICE MANUAL www.dell.com support.dell.com Notes, Notices, and Cautions NOTE: A NOTE indicates important information
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationAPES-14 HD-6500 & HD-7000 Version Operator s Training Manual
APES-14 HD-6500 & HD-7000 Version Operator s Training Manual Issue A1 09/03 PDI Part # 900600 Performance Design Inc. 2350 East Braniff St. Boise Idaho 83716 This manual contains very important safety
More informationHGR-2488 Prism Installation Instructions
HGR-2488 Prism Installation Instructions These installation instructions are applicable to the following models: TASCAM 2488 MK1 (original model) TASCAM 2488 MK II TASCAM 2488 NEO Page 1 of 8 Important
More information100BASE-TX 10BASE-T USB High Speed 2.0. AXXIS HS Print Base & Printer: 720 watts voltage input ranges VAC / Hz or VAC / Hz
Specifications System Data: Print Technology LED Toner Resolution Up to 600 x 1200 dpi Speed Up to 25 ft/min (7.6 M/min) Web Width Up to 8.5 inches (215 mm) Media Core 3 inches (75mm) nominal dia. Max
More informationThe Fone Works. Written By: The Foneworks. This a teardown guide of the PlayStation 3. PlayStation 3 Motherboard Teardown
The Fone Works PlayStation 3 Motherboard Teardown This a teardown guide of the PlayStation 3. Written By: The Foneworks 2017 thefoneworks.dozuki.com Page 1 of 23 INTRODUCTION This is a teardown guide based
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationConstructing a Low-Cost Mobile Eye Tracker
==== Constructing a Low-Cost Mobile Eye Tracker ==== Section 1: Introduction This is a detailed set of instructions on how to build a low-cost mobile eye-tracking system from off-the-shelf components.
More informationOcé User manual. Océ CS2024. Quick Start Guide
Océ User manual Océ CS2024 Quick Start Guide Océ Technologies B.V. Copyright 2005, Océ-Technologies B.V. Venlo, The Netherlands. All rights reserved. No part of this work may be reproduced, copied, adapted,
More informationToshiba Satellite A210 Fan Replacement
Toshiba Satellite A210 Fan Replacement In the guide you will learn how to remove the fan from the Toshiba Satellite A210. Written By: Youlen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION Before
More informationXerox 8264E Color Wide Format Printer 100kg Unwinder / Winder
November 2009 70P3070 Xerox 8264E Color Wide Format Printer 00kg Unwinder / Winder 2009 Xerox Corporation. All rights reserved. Xerox, the sphere of connectivity design, and Xerox 8264E Color Wide Format
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS & ATTACHMENT (MT) P/N 08E70-MKC-A20 GL1800 Honda Dealer: Please give a copy of these instructions to your customer. MII Issue Date January
More informationJuly Manual 10-slide disk outdoor viewer
Ing. J. de Wijs. Populierstraat 44, 4131 AR Vianen, the Netherlands Tel/Fax. +31 (0)347-372242 e-mail: info@dewijs-3d.com Website: www.dewijs-3d.com Design and production of stereoscopic instruments. July
More informationPN: A. ParaDyme System Auxiliary Harness Installation Guide
PN: 602-0259-01-A ParaDyme System Auxiliary Harness Installation Guide LEGAL DISCLAIMER The manufacturer disclaims any liability for damage or injury that results from failure to follow the instructions
More informationINSTALLATION INSTRUCTIONS
Dual Camera Interface for Chrysler, Dodge, Jeep (Kit # 9002-2783 v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Factory T-harness
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationMONARCH 9416 XL QUICK REFERENCE
MONARCH 9416 XL QUICK REFERENCE This Quick Reference contains ribbon loading, supply loading, and general care, maintenance, and troubleshooting procedures for the 9416 XL Thermal Direct and 9416 XL Thermal
More informationLED. Sign Module. Assembly Manual
LED Sign Module Assembly Manual 6/14/2002 3:10 PM 6 2 3 3 E. S a w g ra s s R d S a ra s o ta, F L. 3 4 2 4 0 (9 4 1 )3 7 7-5 7 7 5 F A X(9 4 1 )3 7 8-4 2 2 6 www.acscontrol.com Table of Contents Table
More information