SLG7NT4505 GreenPAK TM. 1 Hz Interrupt Generator. General Description. Pin Configuration
|
|
|
- Alban Gray
- 5 years ago
- Views:
Transcription
1 GreenPAK TM General Description Silego GreenPAK SLG7NT4505 is a low power and small form device. The SoC is housed in a 2mm x 2mm TDFN package which is optimal for using with small devices. Features Low Power Consumption 3.3V Supply Pb-Free / RoHS Compliant Halogen-Free TDFN-8 Package Pin Configuration VDD NMI_GATE MBL_PGOOD_M SENSE TDFN-8 TOP VIEW Output Summary 2 Outputs Open Drain NMOS 1X EX_VREF SMC_RST_N SMC_INIT_CLK GND Thermal Pad connected to GND Silego Technology, Inc. Preliminary Rev 0.11 SLG7NT4505_DS_r011 SLG7NT4505_GP_r001 Revised October 21, 2014
2 Pin Configuration Pin # Pin Name Type Pin Description 1 VDD Power 3.3V Supply Voltage 2 NMI_GATE Digital Input Digital Input without Schmitt trigger 3 MBL_PGOOD_MR Digital Input Digital Input without Schmitt trigger 4 SENSE Analog Input/Output Analog Input/Output 5 GND GND Ground 6 SMC_INIT_CLK Digital Output Open Drain NMOS 1X 7 SMC_RST_N Digital Output Open Drain NMOS 1X 8 EX_VREF Exposed Bottom Pad Analog Input/Output GND GND Ground Ordering Options & Configuration Part Number Package Type SLG7NT4505V SLG7NT4505VTR Analog Input/Output V = TDFN-8 VTR = TDFN-8 Tape and Reel (3k units) SLG7NT4505 SLG7NT4505_DS_r011 Preliminary Page 2
3 Absolute Maximum Ratings Parameter Min. Max. Unit VDD to GND V Voltage at input pins V Current at input pin ma Storage temperature range C Junction temperature C ESD Human Body Model V ESD Machine Model V Electrical Characteristics Symbol Parameter Condition / Note Min Typ Max Unit VDD Supply Voltage V IQ Quiescent Current Static inputs and outputs μa TA Operating temperature o C VAIR Analog Input Voltage Range V VO IO Maximal Voltage Applied to any PIN in High-Impedance State Maximal Average or DC Current (note 1) VDD V Per Each Chip Side ma VIH HIGH-Level Input Voltage Logic Input V VIL LOW-Level Input Voltage Logic Input V VOL LOW-Level Output Voltage Push-Pull, Open Drain Logic (note 1) Level Outputs V IIH HIGH-Level Input Current Logic Input Pins;VIN = VDD na IIL LOW-Level Input Current Logic Input Pins; VIN = 0V na IOL VOFFSET VHYST LOW-Level Output Current (note 1) Analog Comparator Offset Voltage Analog Comparator Hysteresis Voltage (note 1) Open Drain, 1X Driver ma Analog Comparator 0 -- ±20 -- mv ACMP mv RPULL_UP Internal Pull Up Resistance Pull up on PIN kω TDLY0 Time Delay0 Delay ms TDLY2 Time Delay2 Delay ms TSU Start Up Time After VDD reaches 2.5V ms 1. Guaranteed by Design. SLG7NT4505_DS_r011 Preliminary Page 3
4 Description This is a special oscillator with supervisor system. Three inputs are used to control the oscillator. SENSE (PIN4) controls the voltage supply of the chip. If supply voltage decreases down to the threshold set by EX_VREF (PIN8), the chip disables the oscillator and sets SMC_INICK to LOW. When the voltage is bigger than threshold set by EX_VREF is detected on the SENSE pin, SMC_RST_N (PIN7) is set to HIGH with 20 ms delay and enables the oscillator. MBL_PWRGD_MR_N (PIN3) is used for manual reset of SMC_RST_N. Use NMI_GATE (NMI_GATE) to disable the oscillator. SLG7NT4505_DS_r011 Preliminary Page 4
5 Timing Diagram SLG7NT4505_DS_r011 Preliminary Page 5
6 Typical Application Circuit SENSE +3.3V V_SOURCE C1 R1 100nF R3 R4 NMI_GATE MBL_PGOOD_MR U1 1 2 VDD data I/O 8 3 data I data I/O 7 4 data I/O data I/O 6 data I/O GND 5 SLG7NT4505 EX_VREF SMC_RST_N SMC_INIT_CLK R2 SLG7NT4505_DS_r011 Preliminary Page 6
7 Package Top Marking Datasheet Programming Part Code Revision Date Revision Code Number YP A 10/21/2014 SLG7NT4505_DS_r011 Preliminary Page 7
8 Package Drawing and Dimensions TDFN-8 Package SLG7NT4505 SLG7NT4505_DS_r011 Preliminary Page 8
9 Tape and Reel Specification Package Type # of Pins Nominal Package Size Max Units Trailer A Leader B Pocket Reel & Hub Size Length Length per reel per box Pockets Pockets Width Pitch TDFN 8L 2x2mm Green 8 2x2x / Carrier Tape Drawing and Dimensions Package Type Pocket BTM Length Pocket BTM Width Pocket Depth Index Hole Pitch Pocket Pitch Index Hole Diameter Index Hole to Tape Edge Index Hole to Pocket Center Tape Width A0 B0 K0 P0 P1 D0 E F W TDFN 8L 2x2mm Green Recommended Reflow Soldering Profile Please see IPC/JEDEC J-STD-020: latest revision for reflow profile based on package volume of 3.00 mm 3 (nominal). More information can be found at SLG7NT4505_DS_r011 Preliminary Page 9
10 Silego Website & Support Silego Technology Website Silego Technology provides online support via our website at website is used as a means to make files and information easily available to customers. For more information regarding Silego Green products, please visit: Products are also available for purchase directly from Silego at the Silego Online Store at Silego Technical Support Datasheets and errata, application notes and example designs, user guides, and hardware support documents and the latest software releases are available at the Silego website or can be requested directly at info@silego.com. For specific GreenPAK design or applications questions and support please send requests to GreenPAK@silego.com Users of Silego products can receive assistance through several channels: Online Training Silego Technology has live training assistance and sales support available at Please contact us to schedule a 1 on 1 training session with one of our application engineers. Contact Your Local Sales Representative Customers can contact their local sales representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. More information regarding your local representative is available at the Silego website or send a request to info@silego.com Contact Silego Directly Silego can be contacted directly via at info@silego.com or user submission form, located at the following URL: Other Information The latest Silego Technology press releases, listing of seminars and events, listings of worldwide Silego Technology offices and representatives are all available at THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. SILEGO TECHNOLOGY DOES NOT ASSUME ANY LIABILITY ARISING OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. SILEGO TECHNOLOGY RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN, FUNCTIONS AND RELIABILITY WITHOUT NOTICE SLG7NT4505_DS_r011 Preliminary Page 10
SLG7NT4375 SKLAIO. GreenPAK
General Description Silego SLG7NT4375 is a low power and small form device. The SoC is housed in a 1.6 x 1.6 mm STQFN package which is optimal for using with small devices. Features Low Power Consumption
SLG4AX42397 OSFP Low-Speed Module Controller
General Description Dialog is a low power and small formfactor bidirectional interface device for host-side lowspeed OSFP standard interfaces based on a Dialog GreenPAK configurable mixed-signal IC. The
SLG4AX OSFP Low-Speed Module Controller. General Description. Pin Configuration
General Description Dialog is a low power and small formfactor bidirectional interface device for module-side low-speed OSFP standard interfaces based on a Dialog GreenPAK configurable mixed-signal IC.
Environmental G1/G2. Timing & Logic. Discharge S/DIS1. The highest V D being switched must be at FET1 and pin 5 of the SLG55221 and SLG55220
2 Rail GreenFET TM High Voltage Gate Driver Features 5V Power supply Drain Voltage Range 1.0V to 6V Internal Gate Voltage Charge Pump Controlled Load Discharge Rate Controlled Turn on Slew Rate TDFN-8
GreenFET TM High Voltage Gate Driver CC D Q-PUMP + _. Timing & Logic. Discharge
GreenFET TM High Voltage Gate Driver Features 5V ±5% Power supply SLG55021 Drain Voltage Range 1.0V to 20V Internal Gate Voltage Charge Pump Controlled Turn on Delay Controlled Load Discharge Rate Controlled
VCC 1 GND. Environmental. Pb-Free Halogen Free. V D = 20V Max* 5V 3.3V G1/G2 PG 8 DIS2 3
Not for Distribution Features 5V Power supply Drain Voltage Range 1.0V to 20V Internal Gate Voltage Charge Pump Controlled Load Discharge Rate Controlled Turn on Slew Rate TDFN-8 Package Application Functions
MAS6240 Piezo Driver with Multi-Mode Charge Pump
MAS624 Piezo Driver with Multi-Mode Charge Pump Both Single Ended and Differential Output Three-Step Volume Adjusting Up to 8Vpp Output from 3V Supply One Wire Audio & Shutdown Control High Efficiency
A8241. AiT Semiconductor Inc. APPLICATION ORDERING INFORMATION. Low 60mV Dropout at 20mA 4% LED Current Matching
DESCRIPTION The is a CMOS based White/Blue LED driver with stand-alone capability. The driver is primarily designed for LED backlighting of LCD display powered by Li-ion battery with its high efficiency,
Features. Applications
Micro-Power Voltage Supervisor IttyBitty General Description The is a power supply supervisor that provides undervoltage monitoring, manual reset capability, and power-on reset generation in a compact
Features. Description. Applications. Block Diagram PT7M3808. Fixed Voltage Diagram. Adjustable Voltage Diagram(PT7M3808G01)
Features Description Power-On Reset Generator with Adjustable Delay Time: 1.25ms to 10s. Very Low Quiescent Current: 2.8µA Typical High Threshold Accuracy: 0.5% Typ. Fixed Threshold Voltages for Standard
MIC826. General Description. Features. Applications. Typical Application
Voltage Supervisor with Watchdog Timer, Manual Reset, and Dual Outputs In 1.6mm x 1.6mm TDFN General Description The is a low-current, ultra-small, voltage supervisor with manual reset input, watchdog
MIC2790/1/3. General Description. Features. Applications. Typical Application
Supervisor with High-Accuracy, Ultra-Fast Propagation Delay, and Capacitor-Programmable Reset Delay General Description The is ideal for monitoring highly-accurate core voltages that require rapid response
Features. Applications
Push-Button Reset IC General Description The are low-current, ultra-small, pushbutton reset supervisors with long set-up delays. The devices feature two manual reset inputs and two reset outputs. The devices
MIC2790/1/3. General Description. Features. Applications. Typical Application
Supervisor with High-Accuracy, Ultra-Fast Propagation Delay, and Capacitor-Programmable Reset Delay General Description The is ideal for monitoring highly-accurate core voltages that require rapid response
Craft Port Tiny RS-232 Transceiver for Portable Applications ADM101E. Data Sheet FUNCTIONAL BLOCK DIAGRAM
Data Sheet FEATURES 460 kbit/s Transmission Rate Single 5 V Power Supply Compatible with RS-232 Input/Output Levels 0.1 μf Charge Pump Capacitors One Driver and One Receiver On-Board DC-DC Converter ±4.2
Features. Applications
Push-Button Reset IC with Voltage Supervisor General Description The are low-current, ultra-small, pushbutton supervisor reset ICs with an integrated supply voltage monitor. The device features two manual
Low Voltage 1.65 V to 3.6 V, Bidirectional Logic Level Translation, Bypass Switch ADG3233
Data Sheet Low Voltage. V to. V, Bidirectional Logic Level Translation, Bypass Switch ADG FEATURES Operates from. V to. V supply rails Bidirectional level translation, unidirectional signal path -lead
FAN3989 USB/Charger Detection Device with Load Switch
FAN3989 USB/Charger Detection Device with Load Switch Features Charger/USB Detection Device with Load Switch Charger/USB Device Detection Flag Over/Under-Voltage Detection Flag Load Switch Output, Up to
2 Channel Charge Pump Supply for TFT-LCD
.. General Description The is a high perfomance charge pump converter to generate positive and negative voltage supply optimized for small to medium size thin-film transistor(tft) liquid crystal displays
Features. Applications
6GHz, 1:4 CML Fanout Buffer/Translator with Internal I/O Termination General Description The is a 2.5V/3.3V precision, high-speed, fully differential 1:4 CML fanout buffer. Optimized to provide four identical
FAST CMOS OCTAL BUFFER/LINE DRIVER
FAST CMOS OCTAL BUFFER/LINE DRIVER IDT54/74FCT244T/AT/CT FEATURES: Std., A, and C grades Low input and output leakage 1µA (max.) CMOS power levels True TTL input and output compatibility: VOH = 3. (typ.)
4-Channel 1-wire Dimming LED Driver with Ultra Low Dropout Current Source
4-Channel 1-wire Dimming LED Driver with Ultra Low Dropout Current Source FEATURES DESCRITION Ultra low dropout: 50mV/20mA(typical) Support up to 4 LEDs LED sink current up to 20mA ±1% LED current matching(typical)
MIC2782. General Description. Features. Applications. Typical Application. Dual-Input Push Button Reset IC with Immediate and Delayed Outputs
Dual-Input Push Button Reset IC with Immediate and Delayed Outputs General Description The is a two input, two output push button reset IC. It will generate a reset pulse for a factory programmed reset
JC GENERAL DESCRIPTION FEATURES APPLICATIONS TYPICAL APPLIC PIN ASSIGNMENT. 300mA, Low Consumption, Low Dropout, CMOS LDO
GENERAL DESCRIPTION The series arelowdropout linear regulators and optimized to provide a high performance solution for battery power system to delivery low quiescent current. The device offer a new level
VDD = V, TA = -40 C to +85 C, outputs terminated with 100 Ohms between Q and /Q.³
Ultra-Low Jitter 200MHz LVDS XO ClockWorks FUSION General Description The is an ultra-low phase jitter XO with LVDS output optimized for high line rate applications. Features 200MHz LVDS Typical phase
Engineering Specification
Embedded USB Module Engineering Specification Document Number: L5ENG000291 Revision: B No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
A4805 SUPERVISOR (RESET IC) HIGH VOLTAGE HIGH PRECISION VOLTAGE DETECTOR
DESCRIPTION The is a series of high voltage high-precision voltage detectors developed using standard CMOS process. The detection voltage is fixed internally with an accuracy of ±2.4% Nch open-drain. Low
Preamplifier Circuit for IR Remote Control
Preamplifier Circuit for IR Remote Control FEATURES Carrier-out-function: carrier frequency and burst length accurately correspond to the input signal AC coupled response from 20 khz to 60 khz; all data
MAS6240C Piezo Driver with Multi-Mode Charge Pump
DESCRIPTION MAS6240 is a piezo driver device that can drive outputs up to 18Vpp from 3V supply. An internal threemode charge pump generates boosted supply voltage for piezo driver. For adjusting the piezo
MAS6240C Piezo Driver with Multi-Mode Charge Pump
DESCRIPTION MAS6240 is a piezo driver device that can drive outputs up to 18Vpp from 3V supply. An internal threemode charge pump generates boosted supply voltage for piezo driver. For adjusting the piezo
RT mA 5-Channel Charge Pump White LED Driver with Low Dropout Current Source. Features. General Description. Applications. Pin Configurations
General Description The RT9365 is a high performance white LED driver. It integrates current sources and automatic mode selection charge pump. The part maintains the high efficiency by utilizing an x1/x1.5
ILI2303. ILI2303 Capacitive Touch Sensor Controller. Specification
Capacitive Touch Sensor Controller Specification Version: V1.03 Date: 2014/9/17 ILI TECHNOLOGY CORP. 8F, No.38, Taiyuan St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Tel.886-3-5600099; Fax.886-3-5600055
Omnidirectional Microphone with Bottom Port and Analog Output ADMP401
FEATURES 4.72 mm 3.76 mm 1.0 mm surface-mount package High SNR of 62 dba Sensitivity of 42 dbv Flat frequency response from 100 Hz to 15 khz Low current consumption of
Stereo PDM-to-I 2 S or TDM Conversion IC ADAU7002
Data Sheet FEATURES 64 decimation of a stereo pulse density modulation (PDM) bit stream to pulse code modulation (PCM) audio data Slave I 2 S or time division multiplexed (TDM) output interface Configurable
F USB Charger Controller F Release Date: Dec., 2011 Version: V0.11P. Nov., 2011 Data Sheet
USB Charger Controller Release Date: Dec., 2011 Version: V0.11P F75204 Datasheet Revision History Version Date Page Revision History Data Brief 2011/10 - Data Brief 0.10P 2011/ 11 Up Date AC/DC SPECs 0.11P
Low Voltage 1.65 V to 3.6 V, Bidirectional Logic Level Translation, Bypass Switch ADG3233
Low Voltage. V to. V, Bidirectional Logic Level Translation, Bypass Switch FEATURES Operates from. V to. V supply rails Bidirectional level translation, unidirectional signal path -lead SOT- and MSOP packages
Control Circuitry 2 M1. Micrel Inc Fortune Drive San Jose, CA USA tel +1 (408) fax + 1 (408)
Crystal-less Configurable Clock Generator General Description The is a programmable, high performance dual LVDS output oscillator utilizing Micrel's proven silicon MEMS technology to provide excellent
2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS Description. Features. Block Diagram DATASHEET
DATASHEET 2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS557-08 Description The ICS557-08 is a 2:1 multiplexer chip that allows the user to select one of the two HCSL (Host Clock Signal Level) or LVDS input pairs
CEP8120 Rev 1.0, March, 2015
USB Dedicated Charging Port Controller FEATURES Supports USB DCP Shorting D+ Line to D Line per USB Battery Charging Specification, Revision 1.2 (BC1.2) Supports Shorted Mode (Shorting D+ Line to D- Line)
Preamplifier Circuit for IR Remote Control
Preamplifier Circuit for IR Remote Control FEATURES Carrier-out-function: carrier frequency and burst length accurately correspond to the input signal Small QFN package with 2 mm width Can be used with
DSC Q0093. General Description. Features. Applications. Block Diagram. Crystal-less Configurable Clock Generator
Crystal-less Configurable Clock Generator General Description The is a four output crystal-less clock generator. It utilizes Microchip's proven PureSilicon MEMS technology to provide excellent jitter and
LOW EMI PWM INTELLIGENT POWER HIGH SIDE SWITCH
Automotive grade Automotive IPS High side AUIPS72211R LOW EMI PWM INTELLIGENT POWER HIGH SIDE SWITCH Features Integrated bootstrap for 100kHz switching Optimized EMI switching Charge pump for DC operation
3.3V CMOS OCTAL BIDIRECTIONAL TRANSCEIVER
. CMOS OCTAL IDIRECTIONAL TRANSCEIVER. CMOS OCTAL IDIRECTIONAL TRANSCEIVER IDT7FCT/A FEATURES: 0. MICRON CMOS Technology ESD > 00 per MIL-STD-, Method 0; > 0 using machine model (C = 00pF, R = 0) VCC =.
MP6302 Energy Storage and Release Control IC
The Future of Analog IC Technology MP6302 Energy Storage and Release Control IC DESCRIPTION The MP6302 is an energy storage and release controller. It charges storage capacitor from input during normal
AS179-92LF: 20 MHz to 4.0 GHz GaAs SPDT Switch
DATA SHEET AS179-92LF: 20 MHz to 4.0 GHz GaAs SPDT Switch Applications General purpose medium-power switches in telecommunication applications Transmit/receive switches in 802.11 b/g WLAN Bluetooth systems
CARDINAL COMPONENTS, INC.
SERIES CJTDAE CJTDAL The Cardinal Cappuccino Crystal Oscillator LVDS/ LVPECL TCXO Features 3.3V supply voltage- configurable 10MHz to 250MHz LVDS and LVPECL outputs- configurable Better than 2Hz tuning
High-side Power Distribution Switch NCT3521U
High-side Power Distribution Switch NCT3521U -Table of Content- 1. GENERAL DESCRIPTION...1 2. FEATURES...1 3. APPLICATIONS...2 4. PIN CONFIGURATION AND DESCRIPTION...2 5. TYPICAL APPLICATION CIRCUIT...3
Over-Voltage Protection Load Switch with Surge Protection
Over-Voltage Protection Load Switch with Surge Protection FEATURES Surge protection IEC 61000-4-5: > 100V Integrated low Rdson nfet switch: typical 28mΩ 4.5A continuous current capability Default Over-Voltage
RFSA2023TR7. Voltage Controlled Attenuator. Product Overview. Key Features. Functional Block Diagram Applications. Ordering Information
Product Overview Qorvo's is a fully monolithic analog voltage control attenuator (VCA) featuring exceptional linearity over 30dB adjustment range with on-chip temperature compensation. incorporates a revolutionary
User Selectable Up to Two Frequencies LVDS, LVPECL OR CMOS. 6 Pad Standard Package
MVQI Series 5X7 Ceramic SMD VCXO User Selectable Up to Two Frequencies LVDS, LVPECL OR CMOS 6 Pad Standard Package OneClock Range CMOS Range LVDS & LVPECL Temperature Stability* Operating Temperature Range
2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS Features
DATASHEET 2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS557-08 Description The ICS557-08 is a 2:1 multiplexer chip that allows the user to select one of the two HCSL (Host Clock Signal Level) input pairs and
EMIF06-HSD04F3. 6-line low capacitance IPAD for micro-sd card with EMI filtering and ESD protection. Features. Application.
6-line low capacitance IPAD for micro-sd card with EMI filtering and ESD protection Features Datasheet production data Figure 1. Pin configuration (bump side) Very low line capacitance to compensate long
SPECIFICATION Of CMOS MEMS Analog Microphone. Model No.: JL-M2417
SPECIFICATION Of CMOS MEMS Analog Microphone ( RoHS Compliance ) : : ISSUED BY J.C 09-27-2012 CHECKED BY APPROVED BY Version 00 Pages 1 / 11 Revision History Version Description Date Author Approved 00
3.3V CMOS HEX BUFFER/DRIVER WITH OPEN-DRAIN OUTPUTS AND 5 VOLT TOLERANT I/O
3.3V CMOS HEX BUFFER/DRIVER WITH OPEN-DRAIN S AND 5 T TOLERANT I/O IDT74LVC07A FEATURES: 0.5 MICRON CMOS Technology ESD > 200 per MIL-STD-883, Method 3015; > 20 using machine model (C = 200pF, R = 0) VCC
STM6510. Dual push-button Smart Reset TM with capacitor-adjustable delays. Features. Applications
Dual push-button Smart Reset TM with capacitor-adjustable delays Features Dual Smart Reset push-button inputs with capacitor-adjustable extended reset setup delay (t SRC ) Capacitor-adjustable reset pulse
MIC5281. Features. General Description. Applications. Typical Application. 120V IN, 25mA, Ultra-Low IQ, High-PSRR Linear Regulator
120V IN, 25mA, Ultra-Low IQ, High-PSRR Linear Regulator General Description The high-performance linear regulator offers a very-wide input operating voltage range, up to 120V DC, and supplies an output
PWM INTELLIGENT POWER HIGH SIDE SWITCH
July, 2nd 2010 Automotive grade PWM INTELLIGENT POWER HIGH SIDE SWITCH Features Integrated bootstrap for 100kHz switching Charge pump for DC operation Over temperature shutdown Over current shutdown 3.3V
HSP line ESD protection for high speed lines. Applications. Description. Features. µqfn 4 leads. Benefits. Complies with following standards
2-line ESD protection for high speed lines Datasheet - production data Benefits High ESD robustness of the equipment Suitable for high density boards Complies with following standards MIL-STD 883G Method
APX803/D 3-PIN MICROPROCESSOR RESET CIRCUIT. Description. Pin Assignments. Features. Applications APX803. ( Top View ) SOT23. ( Top View ) SOT23R GND
/D Description Pin Assignments The /D is used for microprocessor (µp) supervisory circuits to monitor the power supplies in µp and digital ( Top View ) systems. They provide excellent circuit reliability
DIO5158 1A Lithium Ion Battery Charger IC
DIO5158 Rev 1.5 Features Complete Charge Management for Single Cell Lithium Battery On-chip Power MOSFET No external Blocking Diode or Current Sense Resistors Required Preset 4.2V Regulation Voltage with
DC/DC Converters. TSM Series, 1 Watt. Features. Models
TSM Series, Watt Features SMD package (SOIC-4/8) Construction in lead frame technology Isolated single and dual output I/O isolation 000 VDC High efficiency Operating temperature 40 C to +85 C Reflow solder
DUAL TTL-to-DIFFERENTIAL PECL TRANSLATOR
DUAL TTL-to-DIFFERENTIAL PECL TRANSLATOR FEATURES DESCRIPTION 300ps typical propagation delay
SGM mA, Ultra Low Dropout, Low Power, RF Linear Regulators
GENERAL DESCRIPTION The is a low-power, low-noise, low-dropout, CMOS linear voltage regulator that operates from a 2.5V to 5.5V input voltage. It is the perfect choice for low voltage, low power applications.
SGM803/SGM809/SGM810 Microprocessor Supervisory Circuit in 3-Pin SOT-23
GENERAL DESCRIPTION The supervisory circuits monitor the power supply voltage in microprocessor and digital systems. They provide a reset output during power-up, power-down and brownout conditions. On
MP5013E 5V, 2A, Programmable Current- Limit Switch with Over-Voltage Clamp and Slew Rate Control in a TSOT23-8
MP5013E 5V, 2A, Programmable Current- Limit Switch with Over-Voltage Clamp and Slew Rate Control in a TSOT23-8 DESCRIPTION The MP5013E is a protection device designed to protect circuitry on the output
DIO5151B 700mA/1A Buck/Boost Charge Pump LED Driver
Rev 0.1 Features Output Current : DIO5151BED8: 700mA DIO5151BCD10: 1A Up to 90% Efficiency in Torch Mode Adjustable FLASH Mode Current 1 and 2 Automatic Modes for High Efficiency Input Voltage Range: 3V
4-Line BUS-Port ESD Protection Array - Flow Through Design
-Line BUS-Port ESD Protection Array - Flow Through Design 22736 5 MARKING Pin 1 5F = type code = date code month YY = date code year DESIGN SUPPORT TOOLS click logo to get started Models Available 1 YY
SS1438 Unipolar Hall Switch
Features and Benefits Wide operating voltage range from 2.5V to 24V Medium sensitivity CMOS technology Chopper-stabilized amplifier stage Superior temperature stability Extremely low switchpoint drift
DIO V Current Limited Load Switch
Rev 1.0 DIO7527 Features Input voltage range: 2.7V to 5.5V 2A Maximum Load Current 70mΩ typical R DS(ON) 70μA quiescent current Under-Voltage Lockout High precision over current trigger point Open-drain
Pi-Tek OLED Module PG12864KW Revision: 1.0 May Pi Tek. OLED Module SPECIFICATIONS MODEL NO. : PG12864KW PRODUCT TYPE: STANDARD
Pi Tek OLED Module SPECIFICATIONS MODEL NO. : PG12864KW PRODUCT TYPE: STANDARD This specification may be changed without any notices in order improve performance or quality etc. 1 Content History of versions
Features. LOAD SWITCH or PMIC. LOAD SWITCH or PMIC /RESET
Dual-Input Push Button Reset IC with Immediate and Delayed Outputs General Description The is a two input, two output push-button reset IC. It will generate a reset pulse for a factory-programmed reset
Features. Applications. Micrel Inc Fortune Drive San Jose, CA USA tel +1 (408) fax + 1 (408)
Microprocessor Reset Circuits General Description The MIC809 and MIC810 are inexpensive microprocessor supervisory circuits that monitor power supplies in microprocessor-based systems. The function of
BCT Channel LED Driver (Common-Anode & Common-Cathode) Low Dropout Current Source & Current Sink. General Description. Features.
BCT3220 Low Dropout Current Source & Current Sink General Description The BCT3220 is a high performance white LED driver. The BCT3220 uses an internal resistor to set the bias current for four LEDs, which
MIC705/706/707/708. General Description. Features. Applications. Typical Application. µp Supervisory Circuit
µp Supervisory Circuit General Description The MIC705, MIC706, MIC707, and MIC708 are inexpensive microprocessor supervisory circuits that monitor power supplies in microprocessor-based systems. The circuit
CDMSP M Surface Mount TVS Diode Array
*RoHS COMPLIANT Features RoHS compliant* Protects four I/O lines Ultra-low capacitance ~.55 pf ESD protection > kv Surge protection Applications High Definition Multimedia Interface (HDMI) Digital Visual
SM Features. General Description. Typical Application MHz/312.5MHz and MHz/156.25MHz LVDS Clock Synthesizer.
156.25MHz/312.5MHz and 78.125MHz/156.25MHz LVDS Clock Synthesizer ClockWorks Flex General Description The is a member of the ClockWorks family of devices from Micrel and provides an extremely low-noise
INPAQ Global RF/Component Solutions
TVL 0402 01 SP0 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVL 0402 01 SP0 Size EIA 0402 TVL 0402 01 SP0 Engineering Specification 1. Scope TVL 0402 01 SP0 is a TVS
FXL6408 Fully Configurable 8-Bit I 2 C-Controlled GPIO Expander
October 2012 FXL6408 Fully Configurable 8-Bit I 2 C-Controlled GPIO Expander Features 4X Expansion of Connected Processor I/O Ports Fully Integrated I 2 C Slave 8 Independently Configurable I/O Ports Low-Power
UMD 1423 UNITED MICRO DEVICE INC. Pi filter array with ESD protection. PRODUCT DESCRIPTION APPLICATIONS. This device has 20-bumps 4.
PRODUCT DESCRIPTION UMD1423 is a Pi filter array with TVS diodes for ESD protection. This device has six Pi filters integrated along with four channels of ESD protection. The Pi filters have values of
MX877RTR. 8-Channel, 60V Driver with Push-Pull Output, 3 Wire Interface INTEGRATED CIRCUITS DIVISION. Features. Description.
8-Channel, 6V Driver with Push-Pull Output, 3 Wire Interface Features Eight (8) Outputs Rated at 6V, ±8mA Push-Pull Driver Configuration 6V to 6V Driver Supply Range 2.7V to 5.5V Logic Supply Range 3-Wire
Features. Applications
Ultra-Precision 1:8 CML Fanout Buffer with Internal I/O Termination General Description The is a 2.5V/3.3V precision, high-speed, fully differential CML 1:8 fanout buffer. The is optimized to provide eight
SENSYLINK Microelectronics Co., LTD. (CT1820S) Single-Wire Digital Temperature Sensor
SENSYLINK Microelectronics (CT1820S) Single-Wire Digital Temperature Sensor CT1820S is a Digital Temperature Sensor with±0.5 C Accuracy over -10 C to 80 C. Single-Wire Digital interface is Compatible with
MADR TR. SPDT PIN Diode Driver Rev. V3. Features. Functional Block Diagram. Description. Pin Configuration. Ordering Information
Features Moderate Speed, CMOS Technology (25 ns) Complementary Outputs High Drive Current Capability (± 50 ) Low Current Consumption Plastic SOIC Body for SMT Applications Tape and Reel Packaging Available
A79LXX BIPOLAR LINEAR REGULATOR THREE TERMINAL NEGATIVE VOLTAGE REGULATOR
DESCRIPTION Three-terminal negative voltage regulator. FEATURES Maximum Output current IOM: 100mA Output voltage VO: -/-6V/-8V/-9V/-12V The is available in SOT-23 and TO-92 Packages. Continuous total dissipation
Name Operation Temperature Package Package Mark
USB Charging Controller Features D+/D- DCP Mode per USB Battery Charging Specification 1.2 D+/D- Short Mode per Telecommunication Industry Standard YD/T1591-2009 (Chinese) Supports non-bc1.2 Charging Modes
AUR9801D. Pin Assignments. Description. Applications. Features LI-ION/LI POLYMER BATTERY CHARGER AUR9801D
LI-ION/LI POLYMER BATTERY CHARGER Description Pin Assignments The is a highly-integrated battery charger for single-cell Li-ion or Li-polymer batteries capable of operating with an input voltage reached
HI-8050/51, HI-8150/51 CMOS High Voltage Display Driver
February 2017 HI-8050/51, HI-8150/51 CMOS High Voltage Display Driver GENERAL DESCRIPTION The HI-8050, HI-8051, HI-8150 and HI-8151 are CMOS integrated circuits designed for high voltage LCD display drive
USB-1208LS Specifications
Specifications Document Revision 1.1, February, 2010 Copyright 2010, Measurement Computing Corporation Typical for 25 C unless otherwise specified. Specifications in italic text are guaranteed by design.
STBC ma standalone linear Li-Ion battery charger with thermal regulation. Description. Features. Applications
800 ma standalone linear Li-Ion battery charger with thermal regulation Description Datasheet - production data Features Programmable charge current up to 800 ma No external MOSFET, sense resistors or
STEF12E. Electronic fuse for 12 V line. Datasheet. Features. Applications. Description
Datasheet Electronic fuse for 12 V line Features DFN10 (3x3 mm) Continuous current typ. 3.6 A N-channel on-resistance typ. 45 mω Enable/fault functions Output clamp voltage typ. 15 V Undervoltage lockout
SKY LF: 0.7 to 6.0 GHz High-Isolation (Single-Bit-Control) SPDT Switch
DATA SHEET SKY13522-6LF: 0.7 to 6.0 GHz High-Isolation (Single-Bit-Control) SPDT Switch Applications GSM/DCS/PCS/CDMA/WCDMA/TD-SCDMA single-ended filter switching Features Broadband frequency range: 0.7
CARDINAL COMPONENTS, INC.
SERIES CJAL CJAE The Cardinal Cappuccino Crystal Oscillator LVDS/ LVPECL Features 2.5V or 3.3V supply voltageconfigurable 10MHz to 250MHz LVDS and LVPECL outputs- configurable Better than 2Hz tuning resolution
FE1.1S USB 2.0 HIGH SPEED 4-PORT HUB CONTROLLER
USB 2.0 4-Port Hub FE1.1S USB 2.0 HIGH SPEED 4-PORT HUB CONTROLLER Data Sheet INTRODUCTION The FE1.1s is a highly integrated, high quality, high performance, low power consumption, yet low cost solution
Low cost, 3 Step Dimming Control, Linear AC LED Driver. Features. Applications. Fig. 1 Typical application with 3 Step dimming
Low cost, 3 Step Dimming Control, Linear AC LED Driver General Description The is a non-isolated linear LED driver for general purpose LED lighting applications. It is capable of driving LEDs in multiple
ACE24AC64 Two-wire Serial EEPROM
Description The ACE24AC64 series are 65,536 bits of serial Electrical Erasable and Programmable Read Only Memory, commonly known as EEPROM. They are organized as 8192 words of 8 bits (one byte) each. The
MAX9650/MAX9651 High-Current VCOM Drive Op Amps for TFT LCDs
General Description The MAX965/MAX9651 are single- and dual-channel VCOM amplifiers with rail-to-rail inputs and outputs. The MAX965/MAX9651 can drive up to 13mA of peak current per channel and operate
A24C08. AiT Semiconductor Inc. ORDERING INFORMATION
DESCRIPTION The provides 8192 bits of serial electrically erasable and programmable read-only memory (EEPROM), organized as 1024 words of 8 bits each. The device is optimized for use in many industrial
SM General Description. Features. Block Diagram. ClockWorks TM 125MHz LVDS / 125 MHz HCSL Ultra-Low Jitter Frequency Synthesizer
ClockWorks TM 125MHz LVDS / 125 MHz HCSL Ultra-Low Jitter Frequency Synthesizer General Description The is a member of the ClockWorks family of devices from Micrel and provides an extremely low-noise timing
LP621024E-I Series 128K X 8 BIT CMOS SRAM. Document Title 128K X 8 BIT CMOS SRAM. Revision History. AMIC Technology, Corp.
128K X 8 BIT CMOS SRAM Document Title 128K X 8 BIT CMOS SRAM Revision History Rev. No. History Issue Date Remark 0.0 Initial issue January 14, 2008 Preliminary 1.0 Final version release September 21, 2010
3.3V ZERO DELAY CLOCK BUFFER
3.3V ZERO DELAY CLOCK BUFFER IDT2309A FEATURES: Phase-Lock Loop Clock Distribution 10MHz to 133MHz operating frequency Distributes one clock input to one bank of five and one bank of four outputs Separate