CA SYSVIEW Performance Management CA RS 1307 Service List

Transcription

1 CA SYSVIEW Performance Management CA RS 1307 Service List Description Hiper 13.7 RO53409 CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI **HIPER** RO58701 Abend U Loop in OUTPUT command RO58985 Abend U in JJCL command RO59730 OUTP006I No data or GSV3740W POINT failed after RO58985 RO59977 Abend S0C4 in GSVKCTLG (CATALOG cmd) w/ XSDATA YES **HIPER** The CA RS 1307 service count for this release is 5

2 CA SYSVIEW Performance Management CA RS 1307 Service List Description Hiper 13.5 RO53299 CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI **HIPER** RO58700 Abend U Loop in OUTPUT command RO58984 Abend U in JJCL command RO59729 OUTP006I No data or GSV3740W POINT failed w/ RO58984 The CA RS 1307 service count for this release is 4

3 CA SYSVIEW Performance Management CA RS 1307 Service List Description Hiper 13.0 RO55197 CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI **HIPER** The CA RS 1307 service count for this release is 1

4 CA SYSVIEW Performance Management CA RS 1307 Service List Description Hiper 12.7 NO-SRVC CA RS 1307 Contains No Service For This Release of This Product. The CA RS 1307 service count for this release is 0

5 CA SYSVIEW Performance Management 5 CA RS 1307 Service List for CNM4D00 FMID Service Description Hiper CNM4D00 RO55197 CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI **HIPER** The CA RS 1307 service count for this FMID is 1

6 CA SYSVIEW Performance Management 6 CA RS 1307 Service List for CNM4D50 FMID Service Description Hiper CNM4D50 RO53299 CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI **HIPER** RO58700 Abend U Loop in OUTPUT command RO58984 Abend U in JJCL command RO59729 OUTP006I No data or GSV3740W POINT failed w/ RO58984 The CA RS 1307 service count for this FMID is 4

7 CA SYSVIEW Performance Management 7 CA RS 1307 Service List for CNM4D70 FMID Service Description Hiper CNM4D70 RO53409 CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI **HIPER** RO58701 Abend U Loop in OUTPUT command RO58985 Abend U in JJCL command RO59730 OUTP006I No data or GSV3740W POINT failed after RO58985 RO59977 Abend S0C4 in GSVKCTLG (CATALOG cmd) w/ XSDATA YES **HIPER** The CA RS 1307 service count for this FMID is 5

8 CA SYSVIEW Performance Management CA RS PTF RO RO53409 RO53409 M.C.S. ENTRIES = ++PTF(RO53409) DESC(CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI) Use of the SYSVIEW interface in CA Datacom CICS Services will cause some amount of overhead to be added to transactions when they make database requests, but some new STORAGE OBTAIN / STORAGE RELEASE calls were introduced in this code path in SYSVIEW r13.0 and above. This will result in higher than normal life/cpu times for a transaction. This same overhead problem also exists for callers of the SYSVIEW CICS Monitor Exit Interface (MEI), and on an even worse level than with the CSF interface. The possibility also exists of getting abend S0C4-3B when using either of these interfaces. After upgrading to SYSVIEW r13.0 or higher, transactions making database requests to CA Datacom were reported to have larger response and CPU times, with the additional time being incurred in the CSF statistics within the transaction (CTRANLOG) record. If using the SYSVIEW MEI an increase would also be seen in the MEI times in the Degradation Analysis portion of the transaction detail record. Elongated CICS transaction lifetimes and CPU times. Turn off the SYSVIEW interface in CA Datacom CICS Services by setting DBOC GENOPTS parameter SYSVIEW to NO. CA SYSVIEW r VER(Z038) FMID(CNM4D70) SUP(TSD7028 AR60421). ++HOLD(RO53409) FMID(CNM4D70) SYSTEM REASON(RESTART) DATE(12353) COMMENT( After applying this fix the CICS region must be recycled to pick up the change. Anyone using the GSVCMEI assembler macro for the SYSVIEW/CICS Monitor Exit Interface must reassemble their programs with the updated macro to resolve a potential abend S0C4-3B if the program is running AMODE 64. ).

9 CA SYSVIEW Performance Management CA RS PTF RO RO58701 RO58701 M.C.S. ENTRIES = ++PTF(RO58701) DESC(Abend U Loop in OUTPUT command) Abend U caused by a loop in the OUTPUT command. When scrolling up and down through a JES output file, a loop in module GSVJ1011 is possible, followed by an abend U GSVX488I GSVXRREX STDX$$ ESTAEX, MODE SUP KEY 80 SDWA KEY 88 LEVEL 1 OPTS EA GSVX489I SDWA xxxxxxxx RRXB xxxxxxxx DSA xxxxxxxx GSVX971I TASK CPU LIMIT EXCEEDED (00:05:00) GSVX451E ABEND U IN OUTPUT/DOWN COMMAND GSVX472I USERID userid TERMINAL termname INTERFACE intf GSVX452I SYSVIEW TCB/RB NOT IN CONTROL AT ENTRY TO ABEND GSVX453I DIAGNOSTICS FOR TCB/RB IN CONTROL AT ENTRY TO ABEND GSVX457I PSW 078C2000 address1 ILC 2 INTC 0D GSVX477I KEY 8 STATE SUP AM 31 ASC PRI GSVX458I MODULE GSVXNUC ADDR address2 OFFSET offset GSVX458I NUCMOD GSVXCPUR ADDR address3 OFFSET F2 GSVX450I FIXLVL BASE GSVX473I ROUTNE XCTM$$ ADDR address4 OFFSET A GSVX459I DATA AT PSW ADDR address5 GSVX460I A7F A0DE The user's session will "lock up" while the loop is in progress, and will terminate and need to be restarted after the abend. None. CA SYSVIEW VER(Z038) FMID(CNM4D70) SUP(TSD7104).

10 CA SYSVIEW Performance Management CA RS PTF RO RO58985 RO58985 M.C.S. ENTRIES = ++PTF(RO58985) DESC(Abend U in JJCL command) Abend U in JJCL command. The Storage Release or FREEMAIN macro failed. When the JJCL command is entered on a job which has more 1,000 lines of output, an abend U may occur when attempting to exit (PF3) the JJCL command display. The following messages may be seen on the job log: GSV2543E FREE PERM STORAGE FAILED, ADDR 32C6C000 LEN 00003F34 (15.8K) GSV2541E DESCR JES DS INDEX GSV2542E STORAGE RELEASE RC GSVX488I GSVXRREX STDX$$ ESTAEX, MODE SUP KEY 80 SDWA KEY 88 LEVEL 1 OPTS FA GSVX489I SDWA xxxxxxxx RRXB yyyyyyyy DSA zzzzzzzz GSVX451E ABEND U IN JJCL COMMAND GSVX472I USERID userid TERMINAL terminal INTERFACE ISPF GSVX457I PSW 078C1000 address1 ILC 2 INTC 0D GSVX477I KEY 8 STATE SUP AM 31 ASC PRI GSVX458I MODULE GSVXNUC ADDR address2 OFFSET offset1 GSVX458I NUCMOD GSVXSTGR ADDR address3 OFFSET offset2 GSVX473I ROUTNE FREE$$ ADDR address4 OFFSET offset3 User's SYSVIEW session will terminate and need to be restarted. None. CA SYSVIEW VER(Z038) FMID(CNM4D70) SUP(TSD7106).

11 CA SYSVIEW Performance Management CA RS PTF RO RO59730 RO59730 M.C.S. ENTRIES = ++PTF(RO59730) DESC(OUTP006I No data or GSV3740W POINT failed after RO58985) After the application of PTF RO58985, a user may get either of the following two messages when trying to view job output: OUTP006I No data to display GSV3740W POINT failed for dataset <JES-data-set-name> RC 8, Rsn After the application of PTF RO58985, the following sequence of commands: - LISTFILE jobname - 'S'elect a file - PF3 to return to LISTFILE - 'S'elect the same file again - PF8 to scroll down - PF7 to scroll up will generate one of the following two messages: OUTP006I No data to display GSV3740W POINT failed for dataset <JES-data-set-name> RC 8, Rsn Once either of these messages is received, the user is unable to scroll in either direction. The user is unable to select and scroll through the same output data set more than once. Back out (PF3) of the LISTFILE command and reissue it. CA SYSVIEW VER(Z038) FMID(CNM4D70) PRE(RO58701 RO58985) SUP(TSD7117 AR58985).

12 CA SYSVIEW Performance Management CA RS PTF RO RO59977 RO59977 M.C.S. ENTRIES = ++PTF(RO59977) DESC(Abend S0C4 in GSVKCTLG (CATALOG cmd) w/ XSDATA YES) Issuing the CATALOG command with XSDATA set on may result in an abend S0C4 in module GSVKCTLG. GSVX451E Abend S0C4-10 in CATALOG command GSVX472I Userid <userid> Terminal <terminal> Interface <intf> GSVX452I SYSVIEW SRB in control at entry to abend GSVX453I Diagnostics for SRB in control at entry to abend GSVX457I Psw 078C0000 <address1> Ilc 4 Intc 10 GSVX477I Key 8 State SUP Am 31 Asc PRI GSVX458I Module GSVKCTLG Addr <address2> Offset DE GSVX450I FixLvl BASE GSVX473I Routne UPDX$$ Addr <address3> Offset E GSVX459I Data at PSW addr <address4> GSVX460I 90A050ED DE DE The abend will only occur if the CATALOG command encounters a problem collecting data from other systems. The most likely source of such a problem would be some type of error in CCI (the CA Common Communications Interface), such as: GSVX346E #CCI CONVERSE FAILED, RECEIVE HAS TIMED OUT GSVX345E #CCI CONVERSE FAILED, RC 08 VRC nnnnnnnn XRC nnnnnnnn GSV2602E COMMUNICATION FAILED WITH SYSTEM ssss JOB jjjjjjjj SERVER XSDS GSVX346E #CCI CONVERSE FAILED, RECEIVER NOT FOUND The user session will abend and need to be restarted. Enter the following command from any SYSVIEW screen display to shut off Cross-System Data for the CATALOG command: SET XSDATA NO CATALOG CA SYSVIEW VER(Z038) FMID(CNM4D70) SUP(TSD7123 AR60470).

13 CA SYSVIEW Performance Management CA RS PTF RO RO53299 RO53299 M.C.S. ENTRIES = ++PTF(RO53299) DESC(CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI) Use of the SYSVIEW interface in CA Datacom CICS Services will cause some amount of overhead to be added to transactions when they make database requests, but some new STORAGE OBTAIN / STORAGE RELEASE calls were introduced in this code path in SYSVIEW r13.0 and above. This will result in higher than normal life/cpu times for a transaction. This same overhead problem also exists for callers of the SYSVIEW CICS Monitor Exit Interface (MEI), and on an even worse level than with the CSF interface. The possibility also exists of getting abend S0C4-3B when using either of these interfaces. After upgrading to SYSVIEW r13.0 or higher, transactions making database requests to CA Datacom were reported to have larger response and CPU times, with the additional time being incurred in the CSF statistics within the transaction (CTRANLOG) record. If using the SYSVIEW MEI an increase would also be seen in the MEI times in the Degradation Analysis portion of the transaction detail record. Elongated CICS transaction lifetimes and CPU times. Turn off the SYSVIEW interface in CA Datacom CICS Services by setting DBOC GENOPTS parameter SYSVIEW to NO. CA SYSVIEW r VER(Z038) FMID(CNM4D50) PRE(RO43962 RO46798 RO50179 RO51796) SUP(RO43754 TSD5152 AR60414). ++HOLD(RO53299) FMID(CNM4D50) SYSTEM REASON(RESTART) DATE(13037) COMMENT( After applying this fix the CICS region must be recycled to pick up the change. Anyone using the GSVCMEI assembler macro for the SYSVIEW/CICS Monitor Exit Interface must reassemble their programs with the updated macro to resolve a potential abend S0C4-3B if the program is running AMODE 64. ).

14 CA SYSVIEW Performance Management CA RS PTF RO RO58700 RO58700 M.C.S. ENTRIES = ++PTF(RO58700) DESC(Abend U Loop in OUTPUT command) Abend U caused by a loop in the OUTPUT command. When scrolling up and down through a JES output file, a loop in module GSVJ1011 is possible, followed by an abend U GSVX488I GSVXRREX STDX$$ ESTAEX, MODE SUP KEY 80 SDWA KEY 88 LEVEL 1 OPTS EA GSVX489I SDWA xxxxxxxx RRXB xxxxxxxx DSA xxxxxxxx GSVX971I TASK CPU LIMIT EXCEEDED (00:05:00) GSVX451E ABEND U IN OUTPUT/DOWN COMMAND GSVX472I USERID userid TERMINAL termname INTERFACE intf GSVX452I SYSVIEW TCB/RB NOT IN CONTROL AT ENTRY TO ABEND GSVX453I DIAGNOSTICS FOR TCB/RB IN CONTROL AT ENTRY TO ABEND GSVX457I PSW 078C2000 address1 ILC 2 INTC 0D GSVX477I KEY 8 STATE SUP AM 31 ASC PRI GSVX458I MODULE GSVXNUC ADDR address2 OFFSET <offset1> GSVX458I NUCMOD GSVXCPUR ADDR address3 OFFSET <offset2> GSVX450I FIXLVL BASE GSVX473I ROUTNE XCTM$$ ADDR address4 OFFSET <offset3> GSVX459I DATA AT PSW ADDR address5 GSVX460I A7F A0DE <offset2> = with GSVXCPUR at 13.5 base <offset2> = A with GSVXCPUR at PTF RO48846 <offset3> = with GSVXCPUR at 13.5 base <offset3> = A with GSVXCPUR at PTF RO48846 The user's session will "lock up" while the loop is in progress, and will terminate and need to be restarted after the abend. None. CA SYSVIEW VER(Z038) FMID(CNM4D50) PRE(RO53209) SUP(TSD5209).

15 CA SYSVIEW Performance Management CA RS PTF RO RO58984 RO58984 M.C.S. ENTRIES = ++PTF(RO58984) DESC(Abend U in JJCL command) Abend U in JJCL command. The Storage Release or FREEMAIN macro failed. When the JJCL command is entered on a job which has more 1,000 lines of output, an abend U may occur when attempting to exit (PF3) the JJCL command display. The following messages may be seen on the job log: GSV2543E FREE PERM STORAGE FAILED, ADDR 32C6C000 LEN 00003F34 (15.8K) GSV2541E DESCR JES DS INDEX GSV2542E STORAGE RELEASE RC GSVX488I GSVXRREX STDX$$ ESTAEX, MODE SUP KEY 80 SDWA KEY 88 LEVEL 1 OPTS FA GSVX489I SDWA xxxxxxxx RRXB yyyyyyyy DSA zzzzzzzz GSVX451E ABEND U IN JJCL COMMAND GSVX472I USERID userid TERMINAL terminal INTERFACE ISPF GSVX457I PSW 078C1000 address1 ILC 2 INTC 0D GSVX477I KEY 8 STATE SUP AM 31 ASC PRI GSVX458I MODULE GSVXNUC ADDR address2 OFFSET offset1 GSVX458I NUCMOD GSVXSTGR ADDR address3 OFFSET offset2 GSVX473I ROUTNE FREE$$ ADDR address4 OFFSET offset3 User's SYSVIEW session will terminate and need to be restarted. None. CA SYSVIEW VER(Z038) FMID(CNM4D50) PRE(RO53209) SUP(TSD5210).

16 CA SYSVIEW Performance Management CA RS PTF RO RO59729 RO59729 M.C.S. ENTRIES = ++PTF(RO59729) DESC(OUTP006I No data or GSV3740W POINT failed w/ RO58984) After the application of PTF RO58984, a user may get either of the following two messages when trying to view job output: OUTP006I No data to display GSV3740W POINT failed for dataset <JES-data-set-name> RC 8, Rsn After the application of PTF RO58984, the following sequence of commands: - LISTFILE jobname - 'S'elect a file - PF3 to return to LISTFILE - 'S'elect the same file again - PF8 to scroll down - PF7 to scroll up will generate one of the following two messages: OUTP006I No data to display GSV3740W POINT failed for dataset <JES-data-set-name> RC 8, Rsn Once either of these messages is received, the user is unable to scroll in either direction. The user is unable to select and scroll through the same output data set more than once. Back out (PF3) of the LISTFILE command and reissue it. CA SYSVIEW VER(Z038) FMID(CNM4D50) PRE(RO58700 RO58984) SUP(TSD5220 AR58984).

17 CA SYSVIEW Performance Management CA RS PTF RO RO55197 RO55197 M.C.S. ENTRIES = ++PTF(RO55197) DESC(CICS TRANS OVERHEAD INCREASE WITH DATACOM CSF OR MEI) Use of the SYSVIEW interface in CA Datacom CICS Services will cause some amount of overhead to be added to transactions when they make database requests, but some new STORAGE OBTAIN / STORAGE RELEASE calls were introduced in this code path in SYSVIEW r13.0 and above. This will result in higher than normal life/cpu times for a transaction. This same overhead problem also exists for callers of the SYSVIEW CICS Monitor Exit Interface (MEI), and on an even worse level than with the CSF interface. After upgrading to SYSVIEW r13.0 or higher, transactions making database requests to CA Datacom were reported to have larger response and CPU times, with the additional time being incurred in the CSF statistics within the transaction (CTRANLOG) record. If using the SYSVIEW MEI an increase would also be seen in the MEI times in the Degradation Analysis portion of the transaction detail record. Elongated CICS transaction lifetimes and CPU times. Turn off the SYSVIEW interface in CA Datacom CICS Services by setting DBOC GENOPTS parameter SYSVIEW to NO. CA SYSVIEW r VER(Z038) FMID(CNM4D00) PRE(RO40735 RO46768 RO51690) SUP(RO43783 RO50419 RO51468 TSD0272 AR60418). ++HOLD(RO55197) FMID(CNM4D00) SYSTEM REASON(RESTART) DATE(13051) COMMENT( After applying this fix the CICS region must be recycled to pick up the change. ).