Ethernet-Gateway. Configuration. D Köln Chester Business Park

Transcription

1 Kollmorgen Steuerungstechnik GmbH Kollmorgen Lift Controls Ltd. Broichstrasse 32 Unit 2, The Office Village D Köln Chester Business Park Telefon +49 (0) Chester, Cheshire, CH4 9QP Telefax +49 (0) Telephone + 44 (0) Fax +44 (0) info@kollmorgen.de info@kollmorgen.co.uk KOLLMORGEN Steuerungstechnik GmbH Köln / / DO_EthernetGW_konfig_gb

2 Contents 1 Ethernet-Gateway <<N-Port Express DE-311>> Introduction Configuring the Ethernet Gateway Set the Network Set the Operating State Set the Serial Interface Ethernet-Gateway <<NPort 5110>> Introduction Configuring the Ethernet Gateway Set the Network Set the Serial Interface Set the Operating State Template import configuration Model for the Data Sheet

3 1 Ethernet-Gateway <<N-Port Express DE-311>> 1.1 Introduction This description refers to the <<N-Port Express DE-311>> Ethernet gateway from <<Moxa Technologies Ltd>>. Install the program <<dssetup.exe>> from the product CD on your PC to configure the gateway. You will find this set-up program on the product CD under <<DE-311\software\driver\windows\>>. The software needs Windows 2000 or Windows XP as an operating system. 1.2 Configuring the Ethernet Gateway You can choose two ways to configure it: direct Ethernet connection between the gateway and PC via CROSS OVER cable Laptop Ethernetconnection Gateway RS232 CROSS OVER - cable interfacing via the standard (in-house) network Laptop Gateway RS232 Ethernet-Network The descriptions below refer to the direct Ethernet connection that we recommend and they require the standard factory setting for the configuration. If you would like to reconfigure a machine already that has already configured, reset all values to the standard factory setting. Then, to load the factory settings, press the reset button for at least 10 sec. You can find the reset button on the machine next to the Ethernet interface. Read the instructions in the machine description! Please attend to the DIP switches of the ethernet-gateway. All DIP switches must be located in the OFF position. ON ON OFF

4 Here s how to do it: 1. select the <<Configurator>> input under <<Start/Program/Nport Management Suite/>>. 2. start a network scan under <<Locate Server>> <<Broadcast Search>> 3. the gateway appears in the display 4. select the gateway input and press the right-hand mouse button for the context menu 5. select the <<Modify >> input Do_vl_moxa1 / 50%

5 1.3 Set the Network Do_vl_moxa2 / 50% dialog fields: <<Server Name>> <<IP Address>>* key in the name for identifying the gateways. Please remember that this input is optional and is not a network name <<network mask>>* <<gateway>>* key in the IP address here where the gateway can be reached key in the network mask here for determining the targeted network key in the IP address of the gateway here for a connection to another network <<IP >> retain the <<Static IP>> setting * you can get this information from the network administrator

6 1.4 Set the Operating State Do_vl_moxa3 / 50% dialog fields: <<Change OP_Mode>> tick here and select the <<TCP Server>> input from the <<Port 1>> list <<More settings>> press the button and key in the port number 8000 in the <<TCP Port>> space <<TCP alive check time>> set the value to 1 minute

7 1.5 Set the Serial Interface Do_vl_moxa4 dialog fields: <<Change Serial Port Settings>> tick here select the transmission rate <<9600>> from the <<Baud Rate>> list select the <<None>> input from the <<Flow Control>> list

8 2 Ethernet-Gateway <<NPort 5110>> 2.1 Introduction The discription refers to the Ethernet-Gateway<<NPort 5110>>of <<Moxa Technologies Ltd>> using Windows XP. For configuration of the Ethernet-Gateway please install the programm <<Npadm_Setup_Ver1.12_Build_ exe>> of the product-cd on your PC. The mentioned Setup-programm can be find on your product-cd. Just look for: <<Software\Windows\Npadm_Setup_Ver1.12_Build_ \>>.. Make sure that your operating system meets the minimum requirements for installation. For further information please check your product-cd: <<Software\Windows\version>>. You can find the complete manual on the product-cd <<Document\Nport 5100 Series\>>. 2.2 Configuring the Ethernet Gateway You can choose two ways to configure it: direct Ethernet connection between the gateway and PC via CROSS OVER cable Laptop Ethernet- Verbindung Gateway RS232 CROSS OVER - Kabel interfacing via the standard (in-house) network Laptop Gateway RS232 Ethernet-Netzwerk The descriptions below refer to the direct Ethernet connection that we recommend and they require the standard factory setting for the configuration. If you would like to reconfigure a machine already that has already configured, reset all values to the standard factory setting. To load the factory settings, please push the reset-button for approximately 5 seconds. The Ready -LED starts to flash. You can let go as soon as the LED stops. You can find the reset button on the machine next to the Ethernet interface. Read the instructions in the machine description! ED_DO_MOXA-5110-B

9 Here s how to do it: 1. Select the <<Start/Programme/NPort Administration Suite/>> input under <<Nport Administrator>>. 2. Start a network scan under <<>> <<Broadcast Search>>. 3. The gateway appears in the display. ED_DO_MOXA-5110-B02 \ Bild 55% 4. Select the gateway input and press the right-hand mouse button for the context menu. 5. Select the <<Configure>> input. ED_DO_MOXA-5110-B03 \ Bild 55%

10 2.3 Set the Network ED_DO_MOXA-5110-B04 \ Bild50% Dialog fields: <<Modify>> tick here. <<IP Address>>* key in the IP address here where the gateway can be reached. * you can get this information from the network administrator

11 2.4 Set the Serial Interface ED_DO_MOXA-5110-B05.png \ Bild 50% dialog fields: <<Modify>> Tick here. Select the gateway input. Press the button<<settings>> for detailed settings. ED_DO_MOXA-5110-B06.png \ Bild 50% dialog fields: << Baud Rate >> Select the transmission rate <<9600>>. << Flow Control >> Select the <<None>> input

12 2.5 Set the Operating State ED_DO_MOXA-5110-B07.png \ Bild 50% dialog fields: <<Modify>> Tick here. Select the gateway input. Press the button<<settings>> for detailed settings

13 ED_DO_MOXA-5110-B08.png \ Bild 50% dialog fields: <<Operating Mode>> Choose <<TCP Server Mode>>.out of the list. <<Local TCP Port>> Feed in portnumber <<TCP Alive Check Timeout>> Set the value to 1 minute

14 2.6 Template import configuration ED_DO_MOXA-5110-B09.png \ Bild 55% 1. Start a network scan under <<>> <<Broadcast Search>>. 2. The gateway appears in the display. 3. Select the gateway input and press the right-hand mouse button for the context menu. 4. Select the <<Import >> input. 5. Immediately you reach the basic settings

15 ED_DO_MOXA-5110-B10.png \ Bild 50% dialog fields: <<Modify>> Tick here. Under <<Server Name>> you can fill in the name for Gateway identification. Please remember that this input is optional and is not a network name. Please note: the standard IP-address is pledged in the imported data file. Change the preset IP-address if necessary ( please look up 4.1 network settings ). <<Modify>> Tick here. <<Enable Web Console>> Tick here. <<Enable Telnet Console>> Tick here

16 3 Model for the Data Sheet project: customer: date of installation: control type: VisualLift version: MPK lift version: MPK installation ID: DLON-IO interface version:* DLON v.24 gateway version:* gateway model name: gateway Ethernet (MAC) address: gateway server name: gateway IP address: network mask:* network gateway address:* IP configuration: static IP gateway mode: TCP server TCP server port: 8000 serial parameters: * if available/needed