Pall FBT Series Filter Housings For use in Food and Beverage Production. FBFBT ENb

Transcription

1 Pall FBT Series Filter ousings FBFBT ENb

2 Designed and engineered to meet the demands of Food and Beverage applications, Pall FBT filter housings offer key benefits, which are indispensable in today s food plant operations. Enhanced cleanability and microbiological safety due to crevice-free, polished and hygienic design Ease of installation with proprietary V-band clamp, adjustable connection orientation, and tailored connection options Flexibility to incorporate the extensive range of Pall Food and Beverage filters, providing coarse or fine filtration from 00-0 L/min (- US gpm) Corrosion resistance and durability with L stainless steel wetted parts and high-quality welds Documented quality and food regulation compliance, satisfying the EC Pressure Equipment Directive, ATEX, and FDA requirements for food contact Ability to monitor batch quality with easy to implement filter integrity testing Cost-effectiveness while maintaining the highest quality Pall FBT housings are available in a standard sanitary design allowing a variety of connection options, or in a -A sanitary design, which meets the requirements of -A Sanitary Standards #0-0. Features and Benefits Beveled housing tube sheet and aseptic-style O-ring provide enhanced drainability and a crevice-free connection between the housing head and bowl. Surface finish of the head and elbows is electropolished with chemical passivation, while the bowl is mirror polished. This dual approach ensures optimal cleanability in critical areas while maintaining cost-effectiveness of the housing. New bayonet lock design features additional cut-outs to the traditional half-moon portions of the code bayonet locks. This enhances cleanability and drainability of the housing. Specifications Maximum - to 0 barg Operating (-. to psig) Pressure Maximum, -0 to 0 C Operating ( to 00 F) Temperature Steam Sterilization. barg/0 ºC max. (0 psig/00 ºF max.) Materials of Wetted parts L Construction stainless steel O-Ring Seal EPR Fluorocarbon Elastomer (FKM) Silicone Surface Finish < 0. micron Ra (< Ra microinches) Standard Vent and Drain Connections Filter Cartridge Compatibility Design Specification DIN, tri-clamp, butt weld For other options please contact Pall Pall Code single open-end filter cartridges Design capability of times maximum operating pressure. Each housing is hydrostatically tested to. times maximum For applications involving fluids below 0 C ( F), please contact Pall. Check local pressure vessel code requirements. Seal materials meet FDA requirements for food contact use detailed in CFR Section.00. Additionally, seal materials in -A Series housings meet the requirements specified by -A Sanitary Standards #0-0. EPR seals maximum continuous operating temperature is 0 C (0 F), with steaming resistance to 0 C (00 F). Refer to Pall Food and Beverage filter cartridge literature for additional guidelines on use.

3 Technical Information FBT0 and FBT0 Series ousings Dimensions - FBT0 G (-round housing) ousing A B C D E F G I 0" 0. (.). (.) 0 (.) 0 (.9) () (.) (.) 0 (.9) 9 (.) 0" 00. (.). (.) 0 (.0) 0 (.9) () (.) (.) 0 (.9) 9 (.) 0" 0. (.) 9. (.) 0. (.) 0 (.9) () (.) (.) 0 (.9) 9 (.) 0" 0. (.). (.9) 0 (.) 0 (.9) () (.) (.) 0 (.9) 9 (.) Dimensions FBT0 G (-round housing) A C REQUIRED FOR BOWL REMOVAL B VENT NW DIN E ousing A B C D E F G I 0" 90. (.). (.) 0 (.) 0. (.) 9 (.) 0 (.) 0. (.9) (.). (.) 0". (.). (.) 0 (.0) 0. (.) 9 (.) 0 (.) 0. (.9) (.). (.) 0" 0. (.) 9. () 0. (.) 0. (.) 9 (.) 0 (.) 0. (.9) (.). (.) 0". (.). (.) 0 (.) 0. (.) 9 (.) 0 (.) 0. (.9) (.). (.) ΔP (mbard) Flow Rate (US gpm) Nominal Dimensions in mm (inches) Typical Water Flow / Pressure Drop Characteristics* FBT0 FBT0 Flow Rate (L/min) * Flow/pressure drop characteristics refer to the empty housing only, for water at 0 C ( F). For other liquids, multiply housing pressure drop by the specific gravity of the fluid. 0 9 ΔP (psid) FBT0 ALTERNATIVE CONNECTOR S FBT0 ALTERNATIVE CONNECTOR S G CODE L CODE D F INLET NW DIN I NW0 DIN (.) (.) " (.) (.9).". (.) (.) " 9. (.) (.) "

4 Technical Information FBT0 -A Series ousings Dimensions FBT0 G A (-round housing) ousing A B C D E F G I 0" 0. (.). (.) 0 (.) 0 (.9) () 9 (.) (.) (.) (.) 0" 00. (.). (.) 0 (.0) 0 (.9) () 9 (.) (.) (.) (.) 0" 0. (.) 9. (.) 0. (.) 0 (.9) () 9 (.) (.) (.) (.) 0" 0. (.). (.9) 0 (.) 0 (.9) () 9 (.) (.) (.) (.) Nominal Dimensions in mm (inches) FBT housings that meet the requirements of -A Sanitary Standards #0-0. REQUIRED FOR BOWL REMOVAL A C B E Typical Water Flow / Pressure Drop Characteristics* ΔP (mbard) Flow Rate (US gpm) FBT Flow Rate (L/min) * Flow/pressure drop characteristics refer to the empty housing only, for water at 0 C ( F). For other liquids, multiply housing pressure drop by the specific gravity of the fluid. 0 9 ΔP (psid) G CODE L D F INLET." (.) " I. (.9)

5 Technical Information FBT0 -A Series ousings Dimensions FBT0 G A (-round housing) ousing A B C D E F G I 0" 90. (.). (.) 0 (.) 0. (.) 9 (.) 9 (9.) 9 (.0) (.) 9. (.9) 0". (.). (.) 0 (.0) 0. (.) 9 (.) 9 (9.) 9 (.0) (.) 9. (.9) 0" 0. (.) 9. () 0. (.) 0. (.) 9 (.) 9 (9.) 9 (.0) (.) 9. (.9) REQUIRED FOR BOWL REMOVAL 0". (.). (.) 0 (.) 0. (.) 9 (.) 9 (9.) 9 (.0) (.) 9. (.9) Nominal Dimensions in mm (inches) FBT housings that meet the requirements of -A Sanitary Standards #0-0. C Typical Water Flow / Pressure Drop Characteristics* 00 Flow Rate (US gpm) B A ΔP (mbard) ΔP (psid) E Flow Rate (L/min) FBT0 * Flow/pressure drop characteristics refer to the empty housing only, for water at 0 C ( F). For other liquids, multiply housing pressure drop by the specific gravity of the fluid. F G CODE D INLET I ". (.) (.) "

6 Ordering Information This is a guide to the part number structure and possible options only. For availability of specific options, please contact Pall. Pall Part Number: FBT G Table Table Table Table Table Example Part Number: FBT 0 G NW0 J (See bold reference codes in the tables) Table Code Number of Cartridges 0 0 Table Code Cartridges Nominal Length mm (0") 0mm (0") mm (0") 0mm (0") Table Code Standard Inlet/Outlet Connection FBT0 Option NW0 0mm (DIN ) Male L." Clamp Buttweld Ø0. x.tk FBT0 Option NW0 0mm (DIN ) Male " Clamp Buttweld Ø0. x.tk Table Code Seal Material J EPR Fluorocarbon Elastomer Silicone Table Code Description Blank Standard A -A Series ousing Replacement Parts Description FBT0 FBT0 (-A) FBT0 FBT0 (-A) Material ousing Closure LS00 LS00 ORJPW- ORJPW- EPR Seal Kit CA0 CA0 ORPW- ORPW- FKM CA0 CA0 ORPW- ORPW- Silicone." Clamp Seal LS0009 LS0009 EPR LS009 LS009 FKM LS0009 LS0009 Silicone " Clamp Seal LS000 LS000 EPR LS00 LS00 FKM LS0000 LS0000 Silicone Bowl V-Clamp ACS09DM ACS09DM ACS09DM ACS09DM 0 stainless steel NW DIN Connection ACS09AM ACS09AM L/0/EPR with Stäubli* Vent Tee / ACS09AM ACS09AM L/0/FKM Nut / Seal ACS09AU ACS09AU L/0/Silicone NW DIN Connection ACS09AM ACS09AM L/0/EPR with Gauge (- to ACS099AM ACS099AM L/0/FKM 0bar) / Nut / Seal ACS090AU ACS090AU L/0/Silicone NW DIN Connection ACS09AM ACS09AM L/0/EPR with Stäubli* Vent Valve / ACS09AM ACS09AM L/0/FKM Nut / Seal ACS09AU ACS09AU L/0/Silicone " Coupling with Stäubli* ACS09AM ACS09AM ACS09AM ACS09AM L/0/EPR Vent Tee / V-Clamp / Seal ACS09AM ACS09AM ACS09AM ACS09AM L/0/FKM ACS09AU ACS09AU ACS09AU ACS09AU L/0/Silicone " Coupling with Gauge ACS090AM ACS090AM ACS090AM ACS090AM L/0/EPR (- to 0 bar) / ACS09AM ACS09AM ACS09AM ACS09AM L/0/FKM V-Clamp / Seal ACS099AU ACS099AU ACS099AU ACS099AU L/0/Silicone " Coupling with Stäubli* ACS09AM ACS09AM ACS09AM ACS09AM L/0/EPR Vent Valve / V-Clamp ACS09AM ACS09AM ACS09AM ACS09AM L/0/FKM / Seal ACS09AU ACS09AU ACS09AU ACS09AU L/0/Silicone." V-Clamp ACS009DA 0 stainless steel " V-Clamp ACS0DA 0 stainless steel Clamp, Plates and Bolts CC9 CC0 0 stainless steel Retaining Plate ACS09AA ACS09AA ACS099AA ACS099AA L stainless steel NW Valve, ACS09EM ACS09EM L/0/EPR Nut / Seal ACS099EM ACS099EM L/0/FKM ACS090EU ACS090EU L/0/Silicone Coupling osetail ACS09AM ACS09AM ACS09AM ACS09AM L/0/EPR Valve / V-Clamp / Seal ACS09AM ACS09AM ACS09AM ACS09AM L/0/FKM ACS09AU ACS09AU ACS09AU ACS09AU L/0/Silicone Seal materials meet FDA requirements for food contact use detailed in CFR Section.00. Additionally, seal materials in -A Series housings meet the requirements specified by -A Sanitary Standards #0-0. Only available with." Clamp, " Clamp or Buttweld Ø0. x.tk inlet/outlet connections. Please refer to table. Pall Food and Beverage New York - USA 90 toll free + 00 telephone + 0 fax foodandbeverage@pall.com Portsmouth - UK + (0) 90 9 telephone + (0) fax processuk@pall.com Visit us on the web at Pall Corporation has offices and plants throughout the world in locations including: Argentina, Australia, Austria, Belgium, Brazil, Canada, China, France, Germany, India, Indonesia, Ireland, Italy, Japan, Korea, Malaysia, Mexico, the Netherlands, New Zealand, Norway, Poland, Puerto Rico, Russia, Singapore, South Africa, Spain, Sweden, Switzerland, Taiwan, Thailand, United Arab Emirates, United Kingdom, United States, and Venezuela. Distributors are located in all major industrial areas of the world. Because of developments in technology these data or procedures may be subject to change. Consequently we advise users to review their continuing validity annually. Part numbers quoted above are protected by the Copyright of Pall Europe Limited. and Pall are trademarks of Pall Corporation. Filtration. Separation. Solution is a service mark of Pall Corporation. indicates a trademark registered in the USA. * indicates a trade mark of Stäubli 00, Pall Corporation. May 00. Printed in England. FBFBTENb