Reconfiguring System to Correct Config ID on Citation M2

Transcription

1 Reconfiguring System to Correct Config ID on Citation M2 Garmin G3000 Software Version 10 Caution: Caution: Caution: Caution: Note: Before starting the software or configuration loading process, certain items may be required to be recorded first, to prevent loss of information or settings. See Section 1 for details. Make certain that all SD cards are available before starting. These are usually located in a blue pouch onboard the aircraft (usually in AFM). Follow all steps in a given section for specific loadings. Failure to do so will result in probable rework. Ensure that power is available through a GPU so that power is not interrupted during the loading process. This document is to supplement, not replace, the Cessna Citation M2 MM, and Garmin G3000 LMM. Note: Reference latest revision of the Garmin G3000 LMM Table of Contents Introduction Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Appendix A G3000 System Familiarization Preliminary Steps Prior to Software & Configuration Loading Software & Configuration Loading CMC Diagnostic Configuration Upload Reinstalling Options Aircraft Configuration Final Verification / Return to Service Troubleshooting Configuration ID / CRC Numbers 1

2 Introduction G3000 System Familiarization When in configuration mode, select GDU controls on left side of GTC 1. Ensure that PFD 1 is selected on the screen. The dual concentric knobs on the lower right bezel will be utilized, and throughout this document will be referred to as the FMS small and large knob. The Enter button will be in the lower right part of the screen. As an alternative, you can use the dual concentric knobs (labeled PFD) and Enter button on the GCU-275 controller mounted above PFD 1. Note: Before any work is started, it is important to export the current crew profile to the crew profile SD card. This will restore the pilot preferences (does not include pilot saved waypoints), so that the aircraft is returned to the customer as close as to the same as possible. This card is located in a pouch with all the other SD cards for the Garmin system, and is usually found in the AFM for safe keeping. See section 1 on how to perform this export procedure. 2

3 Section 1 Preliminary Steps Prior to Software & Configuration Loading Saving Crew Profiles 1) First it is necessary to save any customer crew profiles to prevent loss of the settings. From the Home screen on the GTC570, select Utilities. Select Crew Profile. If there are any profiles besides the Default, then they need to be exported to the Crew Profile SD card. Note: The Default crew profile is already on the Crew Profile SD card, and does not need to be exported. If it is the only profile, then no other steps in this section is necessary. 2) Remove the Diagnostics SD card from the upper slot of the MFD. 3) Insert the Crew Profile SD card into the upper slot of the MFD. 4) The crew profiles need to be exported to the SD card: From the Home screen on the GTC570, select Utilities. Select Crew Profile. Select the first saved crew profile. Select Export. 5) Repeat step 4 for any other saved crew profiles. 6) These will be reinstalled later to reload the customer s preferences. 7) Remove the Crew Profile SD card from the upper slot of the MFD. 8) Insert the Diagnostics SD card into the upper slot of the MFD. 3

4 When completing a reconfiguration, the following steps must be completed first: Note: This is with the G3000 powered up in normal mode. Caution: If any optional radio appears to have an amber X and is grayed out as in this example, then the LRU is not installed, but was previously loaded incorrectly. Do not load this option during the procedures in section 3. Determine Options Installed Single GSR56 o On either GTC 570, select the SERVICES / TELEPHONE button, then select Telephone. A single Iridium transceiver is displayed on the left side. Dual GSR56 o On either GTC 570, select the SERVICES / TELEPHONE button, then select Telephone. A double Iridium transceiver is displayed on the left & right side. GDL69 o From the Home screen of either GTC 570, touch the Weather button. Then touch Weather Selection. The option is installed if Sirius XM Settings is displayed. 4

5 Becker ADF o ADF controls are seen on the AUDIO & RADIO screen of either GTC 570. GDR66 o GDR or Datalink controls are seen on the AUDIO & RADIO screen of either GTC 570. Should appear as one of the 2 images below. It may say COM3 or GDR. HF9000 o HF9000 controls are seen on the AUDIO & RADIO screen of either GTC 570. Cabin Briefing o From the Home screen of either GTC 570, select AIRCRAFT SYSTEMS. The option is installed if Cabin Briefing is displayed. 5

6 GSR56 Weather o From the Home screen of either GTC 570, touch the Weather button. Then touch Weather Selection. The option is installed if CONNEXT WEATHER is displayed. Should be if a single or dual GSR 56 is installed. DME 2 o Second DME controls are seen on the AUDIO & RADIO screen of either GTC 570. Synthetic Vision o On the PFD, select PFD Settings, then select Attitude Overlays. Synthetic Terrain is displayed. Also, there should be an unlock SD card present. TAWS Class A o From the Home screen of either GTC 570, select the TAWS button. Then select TAWS Selection button. TAWS A is loaded if there are 6 buttons displayed on the page. Otherwise TAWS B is loaded as default. Also, there should be an unlock SD card present. Note: First image is TAWS B, and second image is TAWS A. 6

7 TCAS II o From the Home screen of either GTC 570, select the transponder button in the upper right part of the screen. TCAS II option is loaded if there are 5 buttons on the left side of the screen. Otherwise, TCAS I is loaded. Also, there should be an unlock SD card present. Note: First image is TCAS I, and second image is TCAS II. Windshear o The Windshear option can be determined by viewing the PFD during power up. During the self test, there should be a WNDSHR TEST white message just to the right of the airspeed tape. Also, there should be an unlock SD card present. Doppler & Turbulence o From the Home screen of either GTC 570, select the Weather button. Then select Weather Selection button. Select the WEATHER RADAR SETTINGS button and the TURBULENCE DETECTION button will be visible. Also, there should be an unlock SD card present. 7

8 CPDLC o The CPDLC button is available on the home screen of either GTC. Also, there should be an unlock SD card present. Radar Trim Settings Go into the left GTC: o Use Back button and select Aircraft Systems. o Select Maintenance. o Enter CACCDMS for password. o Select Radar Trim. Record Pitch Trim Value= Record Roll Trim Value= o If the Radar trims were not both at zero originally: Select Restore Defaults. o Select Home. Select Utilities. Select Setup. Select Avionics Status. Select the Airframe Tab on the left side. Record the Config ID now that the radar trims are zero= This is for reference in case it is needed later. 8

9 Recording Initial Values for Aircraft Equipped with GSR 56 Turn on aircraft power. Go into one of the GTC 570 touch controllers: o Select Aircraft Systems. o Select Maintenance. o Enter CACCDMS as the password. o Select CMC Logs. o Select the Faults folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the LH Service Messages Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the RH Service Messages Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the LH Engine Exceedances Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the RH Engine Exceedances Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the LH Engine Trends Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the RH Engine Trends Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the LH Continuous Log Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the LH Continuous Log Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the RH Continuous Log Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the LH Eng Cal Data Folder. Select the Folder Options. 9

10 Fill in the information in the table below. o Go back and select the RH Eng Cal Data Folder. Select the Folder Options. Fill in the information in the table below. o Go back and select the CAS Messages Folder. Select the Folder Options. Fill in the information in the table below. CMC Folder Tx Type Priority Tx Mode 1 Tx Mode 2 Tx Mode 3 Tx Mode 4 Faults LH Service Messages RH Service Messages LH Engine Exceedances RH Engine Exceedances LH Engine Trends RH Engine Trends LH Continuous Log RH Continuous Log LH Eng Cal Data RH Eng Cal Data CAS Messages 10

11 Section 2 Software & Configuration Loading This section will provide the steps necessary to reload configurations to reset the configuration ID to a proper value. This would be necessary if the config ID is wrong, and it is not known what would have caused it to be incorrect. Note: Anytime that software or configurations are being loaded, all three displays, and both touch controllers must be in configuration mode. Note: Ensure that you have completed the steps contained in section 1, if necessary. Configuration loading: 1) Pull the following circuit breakers: L PFD MFD R PFD L Touch Control R Touch Control 2) Insert the software loader card into the upper slot of PFD 1. 3) Turn on aircraft power. 4) Press and hold the right knob on the left GTC and push the L Touch Control circuit breaker in. Let go when you see initializing. 5) Press and hold the right knob on the right GTC and push the R Touch Control circuit breaker in. Let go when you see initializing. 6) Press and hold the #12 softkey on the #2 PFD and push the R PFD circuit breaker in. Let go when you see initializing. PFD 2 should come up in configuration mode. SYSTEM STATUS should show at the top of the screen. 7) Press and hold the #12 softkey on the MFD and push the MFD circuit breaker in. Let go when you see initializing. MFD should come up in configuration mode. SYSTEM STATUS should show at the top of the screen. 8) Press and hold the #12 softkey on the #1 PFD and turn on power. Let go when you see initializing. 11

12 9) Press the NO softkey at DO YOU WANT TO UPDATE SYSTEM FILES? prompt. 10) Press the NO softkey at DO YOU WANT TO UPDATE THE CUSTOM GRAPHICS FILES (EG, SPLASH SCREEN)? if it appears. 11) PFD 1 should come up in configuration mode. SYSTEM UPLOAD should show at the top of the screen. Clearing Maintenance Log Note: The maintenance log must be cleared before loading the configuration. On the left GTC 570 touch controller: 1) Select GDU Controls. 2) Select MFD on the left side of the screen under GDU block. Rotate the small FMS knob to select the MAINTENANCE LOG on the page. Press the Clear softkey on the MFD. 1) The Erase entire Maintenance Log? prompt will appear. 2) Press Enter. Wait until Clearing Log disappears before continuing. Select PFD 1 on the GTC 570 to switch the display being controlled. Loading Software & Configuration 1) Activate the cursor by pushing down on the FMS knob. 2) Rotate the small knob to drop the menu down, and highlight 525 Base Configuration in the GROUP field. 3) Press the Enter key. 4) Rotate the small knob to drop the menu down, and highlight Cessna Model 525 Base Configuration in the ITEM field. 5) Press the Enter key. 6) Select the CLR ALL softkey at the bottom of the display. 7) Press the CHK CFG softkey. This will check all the configuration boxes. A full configuration is required, and takes approximately 30 minutes. 12

13 12) Select the LOAD softkey at the bottom of the display. 13) A green PASS message is shown beside configuration items as they are successfully completed. 14) Acknowledge when Upload and Crossfill Complete is displayed by pressing the Enter key. 15) Push the UPDT CFG softkey to update the system configuration files. 16) After the software and configuration files are loaded, pull the L PFD circuit breaker, and remove the software loader card from PFD 1. 13

14 Section 3 CMC Diagnostic Configuration Upload Since a full configuration load was completed, then the CMC Diagnostics, Aircraft Configurations, and crew profiles must be loaded. Verify that the configuration ID is correct. All M2 aircraft should have the same ID at this point. Configuration ID Verification= 4F348E7D ** Note: Do not continue past this step if the ID is not correct. The initial configuration loading is not correct. Obtain a spare SD card and load the diagnostic configuration file to it. o File name is avtn_cfg.gca and can be found on Cessna Support under maintenance software of the M2 page. Insert the SD card into the upper slot of the PFD 1. Place the G3000 back in configuration by pressing and hold the #12 softkey on the PFD 1 and pushing in the L PFD circuit breaker. Let go when you see initializing. The system upload page should be visible on the PFD 1. If not use the small PFD knob on the GCU-275 controller above the PFD to select the page by rotating it. o Push in on the knob to get the cursor blinking under the Group line. o Rotate the little knob for the drop down menu and press enter on Model 525 CMC Config. o The cursor will move to the Item line. o Rotate the little knob for the drop down menu and press enter on o Select the LOAD softkey on the bottom of the display. Acknowledge when Upload and Crossfill Complete is displayed. Verify the diagnostic configuration upload succeeded. o On the left GTC, Select GDU Controls. o Select MFD on the left side. o Use the right outer knob on the GTC, and scroll to the GDU tab on the MFD. o Rotate the right inner knob to scroll to the Alert Configuration page on the MFD. o Select the LOG softkey. o Verify that the CMC part number is Pull the L PFD circuit breaker, and remove the SD card from the upper slot of PFD 1. All M2 aircraft should have the same ID right after loading the CMC Diagnostics. Configuration ID Verification= BC ** Note: Do not continue past this step if the ID is not correct. The CMC Diagnostic configuration loading is not correct. 14

15 Section 4 Reinstalling Options This section will provide the steps necessary to reload the options that were originally installed. CAUTION: Only load the options determined to be installed in Section 1. Note: Each option is assuming this is the first you are loading. If you have already loaded an option, then complete this step for steps 1-7 of each option the aircraft is equipped with (not including the unlock cards): 1) Rotate the large knob to the left until in the ITEM field. Single GSR56 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight Single GSR56 Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe System Manifest GDL 59 GDL 59 Router GDL 59 Router File System 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15

16 Dual GSR56 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight Dual GSR56 Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe System Manifest GDL 59 GDL 59 Router GDL 59 Router File System 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. GDL69 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight GDL69 Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe 16

17 System Manifest GDL 69 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. Becker ADF Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight Becker ADF Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: GIA63W 1 Config 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. GDR66 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 17

18 8) Rotate the small knob to drop the menu down, and highlight GDR66 Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe System Manifest GIA63W 2 GDR GDR Aux 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 12) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. HF9000 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight HF9000 Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe GSD ) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 12) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 18

19 Cabin Briefing Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight Cabin Briefing Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: GIA63W 1 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 12) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. GSR56 Weather Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight GSR56 Weather Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe 11) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 12) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 19

20 DME 2 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 3) Let go when you see initializing. 4) PFD 1 should be on the system upload page. 5) Activate the cursor by pushing down on the FMS knob. 6) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 7) Press the Enter key. 8) Rotate the small knob to drop the menu down, and highlight DME 2 Option in the ITEM field. 9) Press the Enter key. 10) All boxes should be checked. These are: Airframe GSD ) Select the LOAD softkey at the bottom of the display. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. Note: Each option using an unlock card is assuming this is the first you are loading. If you have already loaded an option with an unlock card, then step 1 is already complete Synthetic Vision (SVS): 1) Remove the software loader card from the upper slot of PFD 1 if installed. 2) Insert the SVS Unlock card into the upper slot of PFD 1. 3) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 4) Let go when you see initializing. 5) PFD 1 should be on the system upload page. 6) Activate the cursor by pushing down on the FMS knob. 7) Rotate the small knob to drop the menu down, and highlight Configuration Files in the GROUP field. 8) Press the Enter key. 20

21 9) Rotate the small knob to drop the menu down, and highlight Enable SVS Dual PFD in the ITEM field. 10) Press the Enter key. 11) All boxes should be checked. 12) Select the LOAD softkey at the bottom of the display. 13) Monitor the configuration load to verify the green PASS message next to each item. 14) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15) Pull LPFD circuit breaker and remove the SVS Unlock card from the upper slot of PFD 1. TAWS Class A: 1) Remove the software loader card from the upper slot of PFD 1 if installed. 2) Insert the TAWS Class A Unlock card into the upper slot of PFD 1. 3) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 4) Let go when you see initializing. 5) PFD 1 should be on the system upload page. 6) Activate the cursor by pushing down on the FMS knob. 7) Rotate the small knob to drop the menu down, and highlight Configuration Files in the GROUP field. 8) Press the Enter key. 9) Rotate the small knob to drop the menu down, and highlight Enable TAWS-A in the ITEM field. 10) Press the Enter key. 11) All boxes should be checked. 12) Select the LOAD softkey at the bottom of the display. 13) Monitor the configuration load to verify the green PASS message next to each item. 14) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15) Pull LPFD circuit breaker and remove the TAWS Class A Unlock card from the upper slot of PFD 1. 21

22 TCAS II: 1) Remove the software loader card from the upper slot of PFD 1 if installed. 2) Insert the C1 TCAS II Unlock card into the upper slot of PFD 1. 3) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 4) Let go when you see initializing. 5) PFD 1 should be on the system upload page. 6) Activate the cursor by pushing down on the FMS knob. 7) Rotate the small knob to drop the menu down, and highlight TCASII Enablement in the GROUP field. 8) Press the Enter key. 9) Rotate the small knob to drop the menu down, and highlight GTS TCAS II Enablement in the ITEM field. 10) Press the Enter key. 11) All boxes should be checked. 12) Select the LOAD softkey at the bottom of the display. 13) Monitor the configuration load to verify the green PASS message next to each item. 14) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15) Pull LPFD circuit breaker and remove the C1 TCAS II Unlock card from the upper slot of PFD 1. Windshear: 1) Remove the software loader card from the upper slot of PFD 1 if installed. 2) Insert the C7 Windshear Unlock card into the upper slot of PFD 1. 3) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 4) Let go when you see initializing. 5) PFD 1 should be on the system upload page. 6) Activate the cursor by pushing down on the FMS knob. 7) Rotate the small knob to drop the menu down, and highlight Enable_WndShr in the GROUP field. 8) Press the Enter key. 9) Rotate the small knob to drop the menu down, and highlight Windshear Option in the ITEM field. 10) Press the Enter key. 11) All boxes should be checked. 12) Select the LOAD softkey at the bottom of the display. 22

23 13) Monitor the configuration load to verify the green PASS message next to each item. 14) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15) Pull LPFD circuit breaker and remove the C7 Windshear Unlock card from the upper slot of PFD 1. Doppler & Turbulence: CPDLC: 1) Remove the software loader card from the upper slot of PFD 1 if installed. 2) Insert the D2 Doppler & Turbulence Unlock card into the upper slot of PFD 1. 3) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 4) Let go when you see initializing. 5) PFD 1 should be on the system upload page. 6) Activate the cursor by pushing down on the FMS knob. 7) Rotate the small knob to drop the menu down, and highlight Enable_DplrTdGcs in the GROUP field. 8) Press the Enter key. 9) Rotate the small knob to drop the menu down, and highlight GWX Doppler Features in the ITEM field. 10) Press the Enter key. 11) All boxes should be checked. 12) Select the LOAD softkey at the bottom of the display. 13) Monitor the configuration load to verify the green PASS message next to each item. 14) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15) Pull LPFD circuit breaker and remove the D2 Doppler & Turbulence Unlock card from the upper slot of PFD 1. 1) Remove the software loader card from the upper slot of PFD 1 if installed. 2) Insert the F0 CPDLC Unlock card into the upper slot of PFD 1. 3) Press and hold the #12 softkey on the PFD 1 push the L PFD circuit breaker in. 4) Let go when you see initializing. 5) PFD 1 should be on the system upload page. 6) Activate the cursor by pushing down on the FMS knob. 23

24 7) Rotate the small knob to drop the menu down, and highlight Enable_CPDLC in the GROUP field. 8) Press the Enter key. 9) Rotate the small knob to drop the menu down, and highlight FK677A-VHF DataLink (CPDLC/Link 2000+) in the ITEM field. 10) Press the Enter key. 11) All boxes should be checked. 12) Select the LOAD softkey at the bottom of the display. 13) Monitor the configuration load to verify the green PASS message next to each item. 14) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 15) Pull LPFD circuit breaker and remove the F0 CPDLC Unlock card from the upper slot of PFD 1. 24

25 Section 5 Aircraft Configuration Aircraft Configuration Place the G3000 back in configuration by pressing and hold the #12 softkey on the PFD 1 and pushing in the L PFD circuit breaker. Let go when you see initializing. Transponder and TCAS Configuration: o Rotate the inner right knob to go to the Aircraft Configuration page. o The cursor should be on the Aircraft Registration line. Enter the aircraft tail number using the FMS knob to select characters. The VFR code should be set to Note that the Hexadecimal code will need to be entered instead for foreign registered aircraft. Also the VFR code will need to be set to the correct value for the country of registry. o Select the softkey labeled SET GTX1 to program #1 GTX Select OK to acknowledge. o Select the softkey labeled SET GTX2 to program #2 GTX Select OK to acknowledge. o Select the softkey labeled SET GTS to program the GTS Select OK to acknowledge. Aircraft and Engine Serial Numbers Configuration: o Push in on the knob on the left GTC controller to remove the cursor. o Rotate the outer right knob until on the GDU page. o Rotate the inner knob until on the Airframe Configuration page. o Push in on the knob to activate the cursor, which should appear in the engine window. o Rotate the outer knob to place the cursor in the airframe window. Enter the aircraft serial number of 5250*** (substitute the last 3 digits of the aircraft serial number for the ***) using the inner knob to select the characters. There are no dashes in this format. Use the outer knob to change fields. Enter the engine serial numbers exactly as they appear on the engine data plates using the inner knob to select characters. 25

26 Crew Profile Loading Turn aircraft power off. Insert the Crew Profile SD card from the blue pouch into the upper slot of the MFD. Turn aircraft power on. On the left GTC controller, select Aircraft Systems. o Select Maintenance. o Enter password CACCDMS. o Select Set Default Profile. o Select Cessna 525 Profile. Select OK when prompted. Select Home. o Select Utilities. o Select Crew Profile. o Select Restore Defaults. o Select OK when prompted. o Select Import. Select to import any other crew profiles that were exported from section 1. Turn aircraft power off. Remove the Crew Profile SD card, and place back in the blue pouch. 26

27 CMC Diagnostic Configuration (If GSR 56 is Installed) Turn aircraft power on. On the left GTC controller, select Aircraft Systems. Select Maintenance. Enter password CACCDMS. Select CMC Logs. Select the Faults folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 2. Select the LH Service Messages folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 5. Select the RH Service Messages folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 6. Select the LH Engine Exceedances folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 0. Select the RH Engine Exceedances folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 1. Select the LH Engine Trends folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 3. Select the RH Engine Trends folder. o Select the Folder Options 27

28 Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 4. Select the LH Continuous Log folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 8. Select the RH Continuous Log folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 9. Select the LH Engine Cal Data folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 10. Select the RH Engine Cal Data folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 11. Select the CAS Messages folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 7. Go to the Home screen on the GTC. Select Utilities. Select Setup. Select Wi-Fi Setup. Select the Favorites tab on the left side. Verify that the favorites listed in the table below are present. If not: o Select Add Favorite Network. o Enter the SSID, Airport, Security Type, Passphrase, and Mode for all the connections listed in the table below. Press the create button after each connection is entered. 28

29 SSID Airport Security Type Passphrase Mode OEMDIAG KICT WPA CESSNADIAG01 Infrastructure OEMDIAG KIDP WPA CESSNADIAG01 Infrastructure OEMDIAG KSMF WPA CESSNADIAG01 Infrastructure OEMDIAG KIWA WPA CESSNADIAG01 Infrastructure OEMDIAG KSAT WPA CESSNADIAG01 Infrastructure OEMDIAG KMCO WPA CESSNADIAG01 Infrastructure OEMDIAG KGSO WPA CESSNADIAG01 Infrastructure OEMDIAG KMKE WPA CESSNADIAG01 Infrastructure OEMDIAG KSWF WPA CESSNADIAG01 Infrastructure OEMDIAG LEVC* WPA CESSNADIAG01 Infrastructure OEMDIAG LSZH* WPA CESSNADIAG01 Infrastructure OEMDIAG LFPB* WPA CESSNADIAG01 Infrastructure OEMDIAG LKPR* WPA CESSNADIAG01 Infrastructure OEMDIAG EDDL* WPA CESSNADIAG01 Infrastructure OEMDIAG EGCN* WPA CESSNADIAG01 Infrastructure OEMDIAG WSSL* WPA CESSNADIAG01 Infrastructure * Favorite cannot be saved unless Garmin world wide databases are loaded. 29

30 Section 6 Final Verification / Return to Service Note: This is with the G3000 powered up in normal mode. Select Home on the left GTC controller. o Select Utilities. o Select Setup. o Select Avionics Status. o Select the Airframe tab on the left side. o Verify that the configuration ID (CRC Number) matches the number determined in Appendix A based on the options installed in the aircraft. o Select the LRU Info tab on the left side. Verify that all the LRUs are showing green check mark. o Select the MSG button: Verify there is no DB Mismatch message present. Verify there is no Manifest message present. Verify there is no Config message present. If aircraft is equipped with a GDL 69, or GSR 56: o Select Home. o Select Weather. o Select Weather Selection. Verify Connext Weather is present if equipped with a GSR 56. Verify Sirius XM Weather is present if equipped with a GDL 69. If the initial radar trims were not zero: o Select Home on the left GTC controller. o Select Aircraft Systems. o Select Maintenance. o Enter password CACCDMS. o Select Radar Trim. Enter the Pitch and Roll trims recorded in section 1. Return to Service Testing For testing, complete section in the Garmin G3000 LMM. 30

31 Section 7 Troubleshooting This section will provide corrective actions for issues seen after the software is loaded. Substitute LRU name for ***. *** DB Error or *** DB Mismatch o Ensure that the supplemental SD cards are installed in the lower slots of the displays. o Databases do not match. o Verify which database is not the same, and reload as necessary. *** Manifest Error o Software does not match what the system is expecting. o Check work performed and reload necessary software again. *** Config o Configurations do not match what the system is expecting. o Check work performed and reload necessary configurations again. 31

32 Appendix A Configuration ID / CRC Numbers This section will provide details on determining the correct configuration ID or CRC number for a particular M2 aircraft based on the installed options. Through the rest of this section the number will be referred to as a CRC number for simplification. Note: Radar trims that are not at zero for both pitch and roll will cause the number to be different. Ensure they are at zero before verification. Note: Once the CRC number is verified, then the radar trims can be adjusted to the original values. See section 6 for details. Every combination of options that have been ordered or delivered is listed. If you have an aircraft that has been modified in the field that now has a combination not listed, please contact Team M2 at teamm2@txtav.com. Each option is assigned a letter to ensure accuracy when comparing the combination of options to the final number. Options Single GSR 56 (includes GDL 59) --A-- Dual GSR 56 (includes GDL 59) B GDL 69 C WX-1000 Stormscope D Becker ADF E GDR 66 F HF 9000 G Cabin Briefing H GSR 56 Weather K DME 2 M Unlock Cards Synthetic Vision (SVS) N TAWS Class A P TCAS II R Windshear S Doppler & Turbulence T CPDLC V Example: Aircraft has Single GSR, GDL 69, Becker ADF, GDR 66, GSR 56 Weather, SVS, and TCAS II. Its code should be ACEFKNR. This equates to a CRC number of 450CB

33 Option CRC Number Option CRC Number Option CRC Number AC 8D808EC9 ACKM 002A20B9 CFN 705A67B6 ACEF 461C7003 ACKMNPRST BFB15610 CFNP D6F7CAC3 ACEFK 461D07AD ACKMNPST 56B80596 CFNPT 03F4DB35 ACEFKN DC ACKMP 66C783C6 CFNPTV 7F37E14C ACEFKNPR ABAA1C20 ACKMPS 93C49438 CFNRS 0650C8A2 ACEFKNPV C5F4177B ACKMPST COC1A4AA CFNRV 5496BE47 ACEFKNR 450CB913 ACKN F CFNV EB9D6DCD ACEFKR AF ACM F CFP D7 ACEKNPRS F59FE879 AE 92B25F28 CFR 435D5744 ACF 7087D2E2 AEFK 6D8E9B3B CFRS 705A67B6 ACFGHKN 51452D5C AEFKNPSV 1A62BB7B CH D6C5F524 ACFGKMNPRST 3961C814 AEFKPSV 846C5A8F CHNP D359B91D ACFGKN 6FE619E7 AEFKPV 576F4A1D CHP 3D ACFHK 51E77E01 AEFKV F0D1E710 CM E65FDA0D ACFHKN E7DDDEED AEK 92B2F6D2 CMNPST 3CEDBEEA ACFHKNPV C9BE2507 AEKN 28A957BE CMP 4CFD3D1A ACFHKNS 14DAEF5F B CC8FFABE CMPS 79FA4D8C ACFHKNV 6320C1FA BCEFGHKM 7D407A08 CMPST A6F75DFE ACFHKS 7EE48E73 BCEFGHKMNPRSTV C00AD2CE CN 8B5D429B ACFHKV CD2A610E BCEFGHKMPRSTV 2A147B42 CNPRS 87F10694 ACFK 70886ABC BCEFGHKMPRSV FD176AD0 CNS B85A530D ACFKMNPRST A2B89A29 BCEFGHKMPRV D01A5A5E CPR C4FD9536 ACFKMNPST 39BF49AF BCEFGHKMRV 697CF751 CPRS F1FAA5A8 ACFKMNPT 0CC2392D BCEFGHKMV 0083A6D7 CR 5E ACFKMPT 76CBD851 BCEFGKM 5EE16895 CS 2263F221 ACFKMT 102E7544 BCEFGM 5EE0D08B E 91F92276 ACFKN 067ECB78 BE A22497DF EF 6EDEE5E1 ACFKNPRS 03128F71 BEGM 3DD6B028 EFGM 18B25491 ACFKNPS 9A193EF7 BEM A72D823D F 994A48C0 ACFKNPST C7164F69 C F566E1AF FGN 98A7F81B ACFKNPV E85F349C CEF AFF8A3EB FMT 4D ACFKNV 81C1D18F CEFN 45EF04D7 FN 2F40A9AC ACFKP D725CD99 CEFNV C93250AC FNRV 137D003D ACFKPR 401F1E13 CF DA6406CA FNT 5C3DBA1E ACFKPRS 6D1C2E85 CFGN D9C1B625 FNV AA83AFC3 ACFKPS 0422DE0B CFGNPRSV FT C ACFKPST 311FEE7D CFGNPRV 249B6FC3 G 25CBD3C4 ACFKR D981BB06 CFGNPT 6D5C29A4 GN BBC234B0 ACFMT 102DDD9A CFGNRV BDFE0CB6 M 433D6D9B ACHKN 04D69AD4 CFGNV 5504BC3C N 525AE641 ACHKNP 6B73FDE1 CFHN 51B97B2B NRS E851472D ACHKNPS 987E1053 CFMNPST 21EAE405 R 255DD5CF ACHKNPST C56E1EC5 CFMNPT F4EDD393 V 148D4E7D ACK 8D CFMT F85A0F9A 33