Replacing PFD 1 (GDU 1400W) on Citation 750+

Transcription

1 Replacing PFD 1 (GDU 1400W) on Citation 750+ Garmin G5000 Software Version 25 Caution: Caution: Caution: Caution: Before starting the software or configuration loading process, certain items may be required to be recorded first, to prevent loss of information or settings. See Section 1 for details. Make certain that all SD cards are available before starting. These are usually located in a blue pouch onboard the aircraft (usually in AFM). Follow all steps in a given section for specific loadings. Failure to do so will result in probable rework. Ensure that power is available through a GPU so that power is not interrupted during the loading process. Note: This document is to supplement, not replace, the Cessna Citation 750+ MM, and Garmin G5000 LMM. Note: Reference latest revision of the Garmin G5000 LMM Table of Contents Introduction Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Appendix A G5000 System Familiarization References Prior to Certain Software and Configuration Loading Software and Configuration Loading CMC Diagnostic Configuration Upload Reinstalling Options Aircraft Configuration Final Verification / Return to Service Troubleshooting Configuration ID / CRC Numbers 1

2 Introduction G5000 System Familiarization When in configuration mode, select GDU controls on left side of the GTC. Ensure that PFD 1 is selected on the screen. The dual concentric knobs on the lower right bezel will be utilized, and throughout this document will be referred to as the FMS small and large knob. The Enter button will be in the lower right part of the screen. The displays can be individually powered down by turning the outer knob of the respective dimming knob to the left to shut off the display unit. Locations are shown in the above image. An alternative is to pull the respective circuit breakers shown below. PFD 1 o L PFD (Left CB Panel - O4) & L PFD AUX (Left CB Panel - L4) MFD o MFD (Right CB Panel DD2) & MFD AUX (Right CB Panel HH4) PFD 2 o R PFD (Right CB Panel JJ4) 2

3 Note: Before any work is started, it is important to export the current crew profile to the crew profile SD card. This will restore the pilot preferences (does not include pilot saved waypoints), so that the aircraft is returned to the customer as close as to the same as possible. This card is located in a pouch with all the other SD cards for the Garmin system, and is usually found in the AFM for safe keeping. See section 1 on how to perform this export procedure. Section 1 References Prior to Certain Software and Configuration Loading Saving Crew Profiles 1) First it is necessary to save any customer crew profiles to prevent loss of the settings. From the Home screen on the GTC570, select Utilities. Select Crew Profile. If there are any profiles besides the Default, then they need to be exported to the Crew Profile SD card. Note: The Default crew profile is already on the Crew Profile SD card, and does not need to be exported. If it is the only profile, then no other steps in this section is necessary. 2) Remove the Diagnostics SD card from the upper slot of the MFD. 3) Turn the dimmer knob to off for the MFD. 4) Insert the Crew Profile SD card into the upper slot of the MFD. 5) Turn the dimmer knob to on for the MFD. 6) The crew profiles need to be exported to the SD card: From the Home screen on the GTC570, select Utilities. Select Crew Profile. Select the first saved crew profile. Select Export. 7) Repeat step 4 for any other saved crew profiles. 8) These will be reinstalled later to reload the customer s preferences. 9) Remove the Crew Profile SD card from the upper slot of the MFD. 10) Insert the Diagnostics SD card into the upper slot of the MFD. 3

4 Section 1 References Prior to Certain Software and Configuration Loading When replacing a GDU 1400W the following steps must be completed first: Note: This is with the G5000 powered up in normal mode. Caution: If any optional radio appears to have an amber X and is grayed out as in this example, then the LRU is not installed, but was previously loaded incorrectly. Do not load this option during the procedures in section 4. Determine Options Installed Dual HF o HF 1 & HF 2 are seen on the AUDIO & RADIO screen of either MFD GTC 570. GDL69 o From the Home screen of either MFD GTC 570, touch the Weather button. Then touch Weather Selection. The option is installed if Sirius XM Settings is displayed. ADF o ADF controls are seen on the AUDIO & RADIO screen of either MFD GTC

5 GSR56 o From the Home screen of either MFD GTC 570, touch the Services button. A button marked Telephone will appear. Radar Trim Settings Go into the left MFD GTC: o Use Back button and select Aircraft Systems. o Select Maintenance. o Enter CACCDMS as password. o Select Radar Trim. Record Pitch Trim Value= Record Roll Trim Value= o If the Radar trims were not both at zero originally: Select Restore Defaults. Original Config ID (for reference only) o Select Home. Select Utilities. Select Setup. Select Avionics Status. Select the Airframe Tab on the left side. Record the Config ID now that the radar trims are zero= This is for reference in case it is needed later. Empty Weight Value o Select Home. Select Utilities. Select Weight and Fuel. Record the Basic Empty Weight= This will need to be entered back in after the configurations are loaded. 5

6 Recording Initial Values for Aircraft Equipped with GSR 56 Turn on aircraft power. Go into the left MFD GTC 570 touch controllers: o Select Aircraft Systems. o Select Maintenance. o Enter CACCDMS as the password. o Select CMC Logs. o Select the Faults folder. Fill in the information in the table below. o Go back and select the LH Service Messages Folder. Fill in the information in the table below. o Go back and select the RH Service Messages Folder. Fill in the information in the table below. o Go back and select the LH Engine Exceedances Folder. Fill in the information in the table below. o Go back and select the RH Engine Exceedances Folder. Fill in the information in the table below. o Go back and select the LH Engine Trends Folder. Fill in the information in the table below. o Go back and select the RH Engine Trends Folder. Fill in the information in the table below. o Go back and select the LH Continuous Log Folder. Fill in the information in the table below. o Go back and select the LH Continuous Log Folder. Fill in the information in the table below. o Go back and select the RH Continuous Log Folder. Fill in the information in the table below. o Go back and select the LH Eng Cal Data Folder. 6

7 Fill in the information in the table below. o Go back and select the RH Eng Cal Data Folder. Fill in the information in the table below. o Go back and select the CAS Messages Folder. Fill in the information in the table below. CMC Folder Tx Type Priority Tx Mode 1 Tx Mode 2 Tx Mode 3 Tx Mode 4 Faults LH Service Messages RH Service Messages LH Engine Exceedances RH Engine Exceedances LH Engine Trends RH Engine Trends LH Continuous Log RH Continuous Log LH Eng Cal Data RH Eng Cal Data CAS Messages On the left MFD GTC 570 controller: o Select Utilities. o Select Setup. o Select Wi-Fi Setup. o Select Favorites tab on the left side. o Record any Wi-Fi settings not related to the service center network. These are the customer s Wi-Fi networks. Service center network information is recorded at the end of this document already, in case it is needed. 7

8 Section 2 Software and Configuration Loading This section will provide the steps necessary to target load the software and configuration into PFD 1 after replacement. Note: Anytime that software or configurations are being loaded, all three displays, and all four touch controllers must be in configuration mode. Note: Ensure that you have completed the steps contained in Section 1. GDU 1400W PFD 1 When PFD 1 is replaced, then software and configuration loading is required. 1) Pull the following circuit breakers: L PFD GTC (Left CB Panel - E4) MFD L GTC (Left CB Panel - N3) MFD R GTC (Right CB Panel MM4) R PFD GTC (Right CB Panel NN4) 2) Turn the dimmer knob to off for PFD 1, MFD, and PFD 2. 3) Insert the software loader card into the upper slot of PFD 2. 4) Turn aircraft and avionics power on. 5) Press and hold the right knob on the left PFD GTC and push the L PFD GTC circuit breaker (E4) in. Let go when you see initializing. 6) Press and hold the right knob on the left MFD GTC and push the MFD L GTC circuit breaker (N3) in. Let go when you see initializing. 7) Press and hold the right knob on the right MFD GTC and push the MFD R GTC circuit breaker (MM4) in. Let go when you see initializing. 8

9 8) Press and hold the right knob on the right PFD GTC and push the R PFD GTC circuit breaker (NN4) in. Let go when you see initializing. 9) Turn the R PFD dimming knob on to power the display. It may load files from the card. PFD 2 should come up in configuration mode. SYSTEM STATUS should show at the top of the screen. Pull the software loader card from the upper slot of PFD 2. 10) Insert the software loader card into the upper slot of the MFD. 11) Turn the MFD dimming knob on to power the display. It may load files from the card. MFD should come up in configuration mode. SYSTEM STATUS should show at the top of the screen. Pull the software loader card from the upper slot of the MFD. 12) Insert the software loader card into the upper slot of PFD 1. 13) Turn the L PFD dimming knob on to power the display. It may load files from the card. PFD 1 should come up in configuration mode. SYSTEM UPLOAD should show at the top of the screen. Clearing Maintenance Log Note: The maintenance log must be cleared before loading the configuration. On the left MFD GTC 570 touch controller: 1) Select GDU Controls. 2) Select MFD on the left side of the screen under GDU block. Rotate the small FMS knob to select the MAINTENANCE LOG on the page. Press the Clear softkey on the MFD. 1) The Erase entire Maintenance Log? prompt will appear. 2) Press Enter. Wait until Clearing Log disappears before continuing. Select PFD 1 on the GTC 570 to switch the display being controlled. 9

10 Loading Software & Configuration 1) Activate the cursor by pushing down on the FMS knob. 2) Rotate the small knob to drop the menu down, and highlight Model 750 Base Configuration in the GROUP field. 3) Press the Enter key. 4) Rotate the small knob to drop the menu down, and highlight Model 750 Base in the ITEM field. 5) Press the Enter key. 6) Using the arrows on the GTC, highlight CLR ALL at the bottom of the display. 7) Press the Select button on the GTC. 8) Using the arrows on the GTC, highlight CHK CFG at the bottom of the display. 9) Press the Select button on the GTC. A full configuration is required, and takes approximately 45 minutes. 10) Using the arrows on the GTC, highlight LOAD at the bottom of the display. 11) Press the Select button on the GTC. 12) A green PASS message is shown beside configuration items as they are successfully completed. 13) Acknowledge when Upload and Crossfill Complete is displayed by pressing the Enter key. 14) Using the arrows on the GTC, highlight UPDT CFG at the bottom of the display. 15) Press the Select button on the GTC. 16) Select YES, and press the Enter key. 17) Acknowledge when Update Config Complete is displayed by pressing the Enter key. 18) Verify that the configuration ID is correct. Since all configurations were loaded, all 750+ aircraft should have the same ID at this point. Configuration ID Verification= 763BB8D2 ** Note: Do not continue past this step if the ID is not correct. The initial configuration loading is not correct. 19) Rotate the dimmer knob to off for PFD 1, and remove the software loader card from PFD 1. 10

11 Section 3 CMC Diagnostic Configuration Upload Since a full configuration load was completed, then the CMC Diagnostics, Aircraft Configurations, and crew profiles must be loaded. Obtain a spare SD card and load the diagnostic configuration file to it. o File name is avtn_cfg.gca and can be found on Cessna Support under maintenance software of the 750 page. Insert the SD card into the upper slot of the PFD 1. Place the G5000 back in configuration by rotating the dimmer knob to on for PFD 1. The system upload page should be visible on the PFD 1. If not use the small PFD knob on the GCU-275 controller above the PFD to select the page by rotating it. o Push in on the knob to get the cursor blinking under the Group line. o Rotate the little knob for the drop down menu and press enter on Model 750 CMC Config. o The cursor will move to the Item line. o Rotate the little knob for the drop down menu and press enter on o Select the LOAD softkey on the bottom of the display. Acknowledge when Upload and Crossfill Complete is displayed. Verify the diagnostic configuration upload succeeded. o On the left GTC, Select GDU Controls. o Select MFD on the left side. o Use the right outer knob on the GTC, and scroll to the GDU tab on the MFD. o Rotate the right inner knob to scroll to the Alert Configuration page on the MFD. o Select the LOG softkey. o Verify that the CMC part number is Rotate the dimmer knob to off for PFD 1, and remove the SD card from the upper slot of PFD 1. All 750+ aircraft should have the same ID right after loading the CMC Diagnostics. Configuration ID Verification= 079C289C ** Note: Do not continue past this step if the ID is not correct. The CMC Diagnostic configuration loading is not correct. 11

12 Section 4 Reinstalling Options This section will provide the steps necessary to reload the options that were originally installed. CAUTION: Only load the options determined to be installed in Section 1. Note: Each option is assuming this is the first you are loading. If you have already loaded an option, then complete this step for steps 1-6 of each option the aircraft is equipped with (not including the unlock cards): 1) Rotate the large knob to the left until in the ITEM field. Dual HF Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Rotate the dimmer knob to on for L PFD. 3) PFD 1 should come up in configuration mode. PFD 1 should be on the system upload page. 4) Activate the cursor by pushing down on the FMS knob. 5) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 6) Press the Enter key. 7) Rotate the small knob to drop the menu down, and highlight FK632D- Second HF (Full Up) in the ITEM field. 8) Press the Enter key. 9) All boxes should be checked. These are: Airframe Configuration GSD41 3 Configuration 10) Using the arrows on the GTC, highlight LOAD at the bottom of the display. 11) Press the Select button on the GTC. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 12

13 GDL69 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Rotate the dimmer knob to on for L PFD. 3) PFD 1 should come up in configuration mode. PFD 1 should be on the system upload page. 4) Activate the cursor by pushing down on the FMS knob. 5) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 6) Press the Enter key. 7) Rotate the small knob to drop the menu down, and highlight FK632L- SiriusXM (Weather/Music) in the ITEM field. 8) Press the Enter key. 9) All boxes should be checked. These are: Airframe Configuration System Configuration GDL69 Software GDL69 Configuration 10) Using the arrows on the GTC, highlight LOAD at the bottom of the display. 11) Press the Select button on the GTC. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. ADF Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Rotate the dimmer knob to on for L PFD. 3) PFD 1 should come up in configuration mode. PFD 1 should be on the system upload page. 4) Activate the cursor by pushing down on the FMS knob. 5) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 6) Press the Enter key. 7) Rotate the small knob to drop the menu down, and highlight FK658A- ADF in the ITEM field. 8) Press the Enter key. 9) All boxes should be checked. These are: Airframe Configuration GSD41 3 Configuration 13

14 10) Using the arrows on the GTC, highlight LOAD at the bottom of the display. 11) Press the Select button on the GTC. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. GSR56 Option: 1) Insert the software loader card into the upper slot of PFD 1. 2) Rotate the dimmer knob to on for L PFD. 3) PFD 1 should come up in configuration mode. PFD 1 should be on the system upload page. 4) Activate the cursor by pushing down on the FMS knob. 5) Rotate the small knob to drop the menu down, and highlight Options in the GROUP field. 6) Press the Enter key. 7) Rotate the small knob to drop the menu down, and highlight FK676A- Iridium (Voice/Datalink) in the ITEM field. 8) Press the Enter key. 9) All boxes should be checked. These are: Airframe Configuration GDL59 Configuration 10) Using the arrows on the GTC, highlight LOAD at the bottom of the display. 11) Press the Select button on the GTC. 12) Monitor the configuration load to verify the green PASS message next to each item. 13) Press the Enter key when all the loading is complete to acknowledge the upload is complete window. 14

15 Section 5 Aircraft Configuration Aircraft Configuration Fuel & Aircraft Weight o If it is not already installed- insert the software loader card into the upper slot of PFD 1. o Rotate the dimmer knob to on for PFD 1. o PFD 1 should come up in configuration mode. o Verify fuel and aircraft weight are set to the desired unit: Rotate the small FMS knob to go to the SYSTEM SETUP page. Push the FMS knob to activate the cursor. Rotate the large FMS knob to FUEL line in the DISPLAY UNITS box. Rotate the small FMS knob and highlight KILOGRAMS or POUNDS. Press the Enter key. Push the FMS knob to deactivate the cursor. Transponder and TCAS Configuration: o Rotate the small FMS knob to go to the AIRCRAFT CONFIGURATION page. o Push the FMS knob to activate the cursor. o The cursor should be on the Aircraft Registration line. Enter the aircraft tail number using the FMS knob to select characters. The VFR code should be set to Note that the Hexadecimal code will need to be entered instead for foreign registered aircraft. Also the VFR code will need to be set to the correct value for the country of registry. o Using the arrows on the GTC, highlight SET GTX 1 at the bottom of the display. o Press the Select button on the GTC. o Select OK to acknowledge. o Using the arrows on the GTC, highlight SET GTX 2 at the bottom of the display. o Press the Select button on the GTC. o Select OK to acknowledge. o Using the arrows on the GTC, highlight SET GTS at the bottom of the display. o Press the Select button on the GTC. o Select OK to acknowledge. o Push the FMS knob to deactivate the cursor. 15

16 Aircraft and Engine Serial Numbers Configuration: o Rotate the large FMS knob until on the GDU page. o Rotate the small FMS knob until on the AIRFRAME CONFIGURATION page. o Push in on the knob to activate the cursor, which should appear in the engine window. o Rotate the large FMS knob to place the cursor in the airframe window. Enter the aircraft serial number of 7500*** (substitute the last 3 digits of the aircraft serial number for the ***) using the inner knob to select the characters. There are no dashes in this format. Use the outer knob to change fields. Enter the engine serial numbers exactly as they appear on the engine data plates using the inner knob to select characters. 16

17 Crew Profile Loading Turn aircraft power off. Insert the Crew Profile SD card from the blue pouch into the upper slot of the MFD. Turn aircraft power on. On the left GTC controller, select Aircraft Systems. o Select Maintenance. o Enter password CACCDMS. o Select Set Default Profile. o Select Cessna 750 Profile. Select OK when prompted. Select Home. o Select Utilities. o Select Crew Profile. o Select Restore Defaults. o Select OK when prompted. o Select Import. Select 7500*** Crew Profile that was stored earlier (substitute the last 3 digits of the aircraft serial number for the ***). Note: Also import any other crew profiles that were exported from section 1. o Select Activate. Select 7500*** Crew Profile (substitute the last 3 digits of the aircraft serial number for the ***). o When finished, the system displays the name of the selected crew profile in the Active Profile window. Turn aircraft power off. Remove the Crew Profile SD card, and place back in the blue pouch. Nav Database **Important Step** Since the Nav Data database resides in the internal memory of the display, it is necessary to reload the database to the new PFD 1. o It may automatically update the active, by pulling the standby database from the lower SD card. If it does not: Instructions available in the Garmin Avionics Expert System. If this is not accomplished, an amber X will appear on the CAS message window. 17

18 CMC Diagnostic Configuration (If GSR 56 is Installed) Turn aircraft power on. On the left MFD GTC controller, select Aircraft Systems. Select Maintenance. Enter password CACCDMS. Select CMC Logs. Select the Faults folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 2. Select the LH Service Messages folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 5. Select the RH Service Messages folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 6. Select the LH Engine Exceedances folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 0. Select the RH Engine Exceedances folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 1. Select the LH Engine Trends folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 3. Select the RH Engine Trends folder. o Select the Folder Options 18

19 Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 4. Select the LH Continuous Log folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 8. Select the RH Continuous Log folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 9. Select the LH Engine Cal Data folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 10. Select the RH Engine Cal Data folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 11. Select the CAS Messages folder. o Select the Folder Options Input the Tx Type and Tx Modes (1-4) that were recorded in the table in section 1. Unless the owner had set the priority different- set the priority to 7. Go to the Home screen on the GTC. Select Utilities. Select Setup. Select Wi-Fi Setup. Select the Favorites tab on the left side. Verify that the customer s Wi-Fi settings are still showing. If not: o Select Add Favorite Network. o Enter the SSID, Airport, Security Type, Passphrase, and Mode for the networks recorded earlier in the instructions. Press the create button after each connection is entered. 19

20 Verify that the favorites listed in the table below are present. If not: o Select Add Favorite Network. o Enter the SSID, Airport, Security Type, Passphrase, and Mode for all the connections listed in the table below. Press the create button after each connection is entered. SSID Airport Security Type Passphrase Mode OEMDIAG KICT WPA CESSNADIAG01 Infrastructure OEMDIAG KIDP WPA CESSNADIAG01 Infrastructure OEMDIAG KSMF WPA CESSNADIAG01 Infrastructure OEMDIAG KIWA WPA CESSNADIAG01 Infrastructure OEMDIAG KSAT WPA CESSNADIAG01 Infrastructure OEMDIAG KMCO WPA CESSNADIAG01 Infrastructure OEMDIAG KGSO WPA CESSNADIAG01 Infrastructure OEMDIAG KMKE WPA CESSNADIAG01 Infrastructure OEMDIAG KSWF WPA CESSNADIAG01 Infrastructure OEMDIAG LEVC* WPA CESSNADIAG01 Infrastructure OEMDIAG LSZH* WPA CESSNADIAG01 Infrastructure OEMDIAG LFPB* WPA CESSNADIAG01 Infrastructure OEMDIAG LKPR* WPA CESSNADIAG01 Infrastructure OEMDIAG EDDL* WPA CESSNADIAG01 Infrastructure OEMDIAG EGCN* WPA CESSNADIAG01 Infrastructure OEMDIAG WSSL* WPA CESSNADIAG01 Infrastructure * Favorite cannot be saved unless Garmin world wide databases are loaded. 20

21 Section 6 Final Verification / Return to Service Note: This is with the G5000 powered up in normal mode. Select Home on the left MFD GTC controller. o Select Utilities. o Select Setup. o Select Avionics Status. o Select the Airframe tab on the left side. o Verify that the configuration ID (CRC Number) matches the number determined in Appendix A based on the options installed in the aircraft. o Select the LRU Info tab on the left side. Verify that all the LRUs are showing green check mark. o Select the MSG button: Verify there is no DB Mismatch message present. Verify there is no Manifest message present. Verify there is no Config message present. Select Home on the left MFD GTC controller. o Select Utilities. o Select Weight and Fuel. o Select Set Empty Weight. Enter the value recorded in section 1 and select Enter. If aircraft is equipped with a GDL 69, or GSR 56: o Select Home. o Select Weather. o Select Weather Selection. Verify Connext Weather is present if equipped with a GSR 56. Verify Sirius XM Weather is present if equipped with a GDL 69. If the initial radar trims were not zero: o Select Home on the left MFD GTC controller. o Select Aircraft Systems. o Select Maintenance. o Enter password CACCDMS. o Select Radar Trim. Enter the Pitch and Roll trims recorded in section 1. Return to Service Testing For testing, complete section 7.16 in the Garmin G5000 LMM. 21

22 Section 7 Troubleshooting This section will provide corrective actions for issues seen after the software is loaded. Substitute LRU name for ***. Amber X on CAS Message Window o NavData was not loaded into the replacement GDU1400W, as it is loaded into the internal memory. o Reload the NavData database into the replacement GDU1400W. Fuel and Aircraft Weights in Kilograms Instead of Pounds o The steps in the aircraft configuration in section 5 were not completed. After a display change, the system wants to revert to kilograms. *** DB Error or *** DB Mismatch o Ensure that the supplemental SD cards are installed in the lower slots of the displays. o Databases do not match. o Verify which database is not the same, and reload as necessary. *** Manifest Error o Software does not match what the system is expecting. o Check work performed and reload necessary software again. *** Config o Configurations do not match what the system is expecting. o Check work performed and reload necessary configurations again. 22

23 Appendix A Configuration ID / CRC Numbers This section will provide details on determining the correct configuration ID or CRC number for a particular 750+ aircraft based on the installed options. Through the rest of this section the number will be referred to as a CRC number for simplification. Note: Radar trims that are not at zero for both pitch and roll will cause the number to be different. Ensure they are at zero before verification. Note: Once the CRC number is verified, then the radar trims can be adjusted to the original values. See section 6 for details. Every combination of options that have been ordered or delivered is listed. If you have an aircraft that has been modified in the field that now has a combination not listed, please contact Team X at citationx@txtav.com. Each option is assigned a letter to ensure accuracy when comparing the combination of options to the final number. Options Dual HF GDL 69 ADF GSR 56 Unlock Cards TAWS A Callouts --A-- B C D E Example: Aircraft has Dual HF, GDL 69, and GSR 56. Its code should be ABD. This equates to a CRC number of 37CDF

24 Option CRC Number Option CRC Number Option CRC Number A E722146A AB ABBF72F2 ABC 32659D15 ABCD BE741A74 ABCDE 20A29765 ABD 37CDF051 ACD 1FD6BCAA B CC BC 4B97B147 BCD D7A62EA6 BD C 86FA52BF CD 39D8D0DC 24