Pilot Scout 3.0 Datasheet V14.1

Transcription

1 Pilot Scout 3.0 Datasheet V14.1

2 Contents Contents 1 What's New in This Release? Overview Brief Introduction System Architecture Performance & Feature Test Services Features Application Scenarios Supported Modules Hardware Specification Technical Support and Contact Information Technical Support Link to DingLi Appendix Comparison between Pilot Scout 2.1 and Pilot Scout

3 What's New in This Release? 1 What's New in This Release? 1. High performance intel X86 CPU (quad-core processor) for more stable testing 2. Supports 16GB or 32GB RAM. 3. Supports dual-channel LTE 2CC/3CC CA test 4. MO/MT test with POLQA (MOS) audio quality measurement, supporting 16k or 48k sample rate. 5. Supported modules: One dedicated modem for data upload and two dedicated test modules. 6. Supports 4x2 MIMO 7. The high sensitivity GPS chipset comes with built-in antenna and external antenna. Dingli may install the built-in or external antenna depending on users' requirement. 8. Better quality with aluminum alloy shell and larger screen to view various modules' information conveniently 9. Larger heat dissipation area 3

4 Overview 2 Overview 2.1 Brief Introduction Pilot Scout 3.0 is newly designed from the ground up to meet the demanding test and measurement requirements of the latest 4G LTE network features. This version of Pilot Scout comes with an impressive list of new features, with high-performance CPU and built-in high-sensitivity GPS chipset among them. It is an autonomous mobile network test equipment with a compact design and highly stable operating system. This makes it suitable for small or discreet installation spaces, while being remotely managed by Pilot Fleet Unify system for automated testing and backend data processing Pilot Scout 3.0 is Dingli s most portable and cost-efficient remote test equipment, suitable for large-scale deployment. The main features are as below: Portable test and measurement solution supporting services testing under all major network technologies, including voice, MOS, HTTP, FTP, Video Play and SpeedTest etc. Built-in two test modules and one independent Modem module for real-time data transmission Connected to Pilot Watcher tablet for onsite real-time test status monitoring Embedded system that is able to integrate with baseband chip supporting various network technologies and internal Linux system, ensuring device stability and reliability Supported technologies: CDMA IS95/1X/EVDO, TD-SCDMA/HSDPA, GSM/EDGE/GPRS, UMTS/HSDPA/ HSUPA/HSPA+, and LTE/LTE-A(2CC/3CC) Distributed coverage of test probes, positioned within unique and strategic locations in the operator's network Probes administration, and measurement data transfer is managed through a central server System management, administration, reports generation and control performed through a web browser. 2.2 System Architecture Pilot Scout 3.0 can mutually communicate with the Pilot Fleet Unify central server over TCP/IP. The upstream communication handles uploading of test results, collected data, and alarms from Pilot Scout to the central server, while the downstream communication handles distribution of commands and test tasks from the central server to Pilot Scout. See Figure

5 Overview Figure 2.1 System architecture 5

6 Performance & Feature 3 Performance & Feature 3.1 Test Services Pilot Scout supports the following services test: 2G/3G/4G MO/MT MOS Test (POLQA/PESQ, CS/VoLTE/CSFB) FTP Download FTP Upload HTTP Page/Download Video Play (e.g. Youtube) PING Speed Test 3.2 Features Pilot Scout 3.0's main features are as below: Pocket-sized for indoor test and drive test Intel X86 CPU (quad-core processor), ensuring high performance with low power consumption Supports GSM, GPRS/EDGE, CDMA, EVDO, TD-SCDMA, UMTS/HSDPA/HSPA+, and LTE/LTE-A technologies. Supports service test with two test modules (which support built-in 4x2 MIMO antenna), with real-time data upload to Pilot Fleet Unify server simultaneously. Supports CSFB/VoLTE MO/MT test. Supports WiFi b/g/n/ac (2.4GHz and 5.8GHz WIFI) (optional). Connected to Pilot Watcher tablet for real-time test status monitoring Built-in 8 Generation U-Blox multi-mode GPS module In-vehicle OLED screen that may display real-time test progress and status 3.3 Application Scenarios The application scenarios of Pilot Scout 3.0 are as below: Remote and autonomous indoor test: Pilot Scout, which is remotely controlled, can be deployed in densely populated public places, such as Shopping Mall, office building, metro station, airport, etc. Pilot Scout can be used to conduct long-term indoor tests, collecting high volume data reflecting true network quality and performance. Cell Site Monitoring: Pilot Scout 3.0 can be deployed by co-locating with the cell site or near it, to monitor the cell site performance. If any error is detected, Pilot Scout may send out alarm information. Dual-channel autonomous test: Pilot Scout 3.0 can be installed in public transportation such as taxis, buses, or trains, and can be used to conduct long-term tests and data collection 6

7 Performance & Feature based on defined test plans. Test data collected by Pilot Scout may be uploaded to Pilot Fleet Unify server for real-time analysis and test status monitoring. Monitoring Major Events: During major events, Pilot Scout 3.0 can be deployed in corresponding areas to monitor network performance in real-time, and identify and troubleshoot the possible network problems. Unique test positioning: Pilot Scout 3.0 can be used in areas not reachable with traditional drive test tool or with a vehicle, due to its unique form factor. Detecting and troubleshooting network problems from the daily test: In some cases, a shortterm test is not enough to detect specific network problems. Pilot Scout can be deployed on the site to continuously collect data and detect network problems for troubleshooting. 3.4 Supported Modules Module information of SIM2 and SIM3 channels: Module Frequency Module 1 WCDMA: 850/1900/2100 MHz GSM/GPRS/EDGE: 850/900/1800/1900 MHz Module 2 FDD-LTE: Band 1/3/7/17 TDD-LTE: Band 38/39/40/41 WCDMA: Band 1/2/5/8 GSM: 1900/1800/900/850 MHz Module 3 FDD-LTE: Band 1/2/3/4/5/7/8/20/26/28 TDD-LTE: Band 38/39/40/41 WCDMA/HSPA+: Band 1/2/5/8 Quad-band EDGE/GPRS/GSM: 1900/1800/900/850 MHz FDD-LTE: Band 1/3 Module 4 TDD-LTE: Band 38/39/40/41 WCDMA: Band 1 CDMA: Band BC0 GSM: 900E/1800 Module 5 FDD-LTE: Band 1/2/3/4/5/7/8/20/26/28 TDD-LTE: Band 38/39/40/41 WCDMA: Band 1/2/4/5/8 7

8 Performance & Feature Module Frequency CDMA/EVDO: Band bc0/bc1 GSM: 1900/1800/900/850 MHz CA: Intra-band contiguous: 2/3/4/7/38/39/40/41 Intra-band non-contiguous: 2/3/4/7/41 Inter-band: 1+3, 1+5, 1+7, 1+8, 1+20, 1+26, 3+5, 3+7, 3+8, 3+20, 3+26, 3+28, 7+20, 7+28, 5+7, (support LTE Cat 6) Module 6 FDD_LTE: Band 1/2/3/4/5/7/8/12/13/17/20/28/30 TDD-LTE: Band 38/39/40/41 HSPA/UMTS: Band 1/2/4/5/8 GSM/GPRS/EDGE: 850/900/1800MHz EVDO/CDMA: BC0/BC1 3DL CA: B3+B7+B8; 2DL CA: B3+B7/ B3+B8/ B7+B3/ B8+B3 Other CA combinations can be customized. 8

9 Hardware Specification 4 Hardware Specification Item Description Color CPU Flash Disk Configuration Supported technologies Wi-Fi GPS Antenna Host, silver gray x86 Intel, quad-core 16G/32GB Flash memory Modem*1+ Testing Module*2+ WIFI+ GPS 2G/3G/4G (FDD-LTE/TDD-LTE/LTE-2CC CA/ LTE-3CC CA) For details about each module, see section 3.4. IEEE b/g/n/ac, 2.4/5.8 GHz GPS/GNSS/BEIDOU navigation, built in or external antenna Built-in antenna for Modem, test module and WIFI; built-in GPS antenna (optional) Human-computer Interface Capacitive sensing button*3 on Pilot Scout panel Indicator light *4 Button Power button *1 Interface Micro USB interface *1 for development and debugging External GPS antenna interface *1 USB 2.0 extended interface*2 Nano SIM card slot *3 Dimension Weight 198 x 130 x 29.5 mm Around 900 g (with battery) In-built Li Battery (UPS) Rated Voltage: 7.4 V Rated Capacity: 2000 mah UPS performance is from 90 to 120 minutes Power Consumption 9 W (typ.) 18W (max.) Standby Power 20 mw (powered by battery only) Consumption 9

10 Hardware Specification Item Description Battery From 90 to 120 minutes Performance Input Power Work Current Operating Environment Accessories (optional) 10 to 30 V DC, 2 A 0.75 A (avg.), 1.5 A (max. internal battery charge) Working temperature: -20 to +50 C Storage temperature: -45 to +85 C Humidity: no more than 93%RH, +40 C vehicular adapter (for coach to convert Voltage from 24 V to 12 V), and mounting plate (to secure the device to a wall) Note: Built-in GPS antenna is optional in Pilot Scout 3.0, since the device is installed with external GPS antenna as default, which may satisfy more drive test scenarios. 10

11 Technical Support and Contact Information 5 Technical Support and Contact Information 5.1 Technical Support For any product usability issues encountered during operation, please refer to the user manual. If the issue cannot be solved or information is not available, please contact us via the following contact information: Area Global support@dingli.com 5.2 Link to DingLi For more product information or service and technical support, please visit us at 11

12 Appendix 6 Appendix 6.1 Comparison between Pilot Scout 2.1 and Pilot Scout 3.0 Feature Pilot Scout 2.1 Pilot Scout 3.0 Colour Black Silvery grey CPU ARM, quad-core x86 Intel, quad-core Flash Disk 4G /8G/16GB Flash memory 16G/32GB Flash memory Configuration 1 Modem + 1 Test Module + WIFI + GPS + Bluetooth 1 Modem + 2 Test Module + WIFI+ GPS Supported technologies 2G/3G/4G (FDD-LTE/TDD-LTE) 2G/3G/4G (FDD-LTE/TDD-LTE/LTE- 2CC CA/LTE-3CC CA) Wi-Fi IEEE b/g/n/ac, 2.4/5.8 GHz IEEE b/g/n/ac, 2.4/5.8 GHz WiFi Testing Yes Yes GPS Built in GPS; supports external antenna GPS/GNSS/BEIDOU Navigation or Bluetooth GPS Satellite System for positioning; built in Antenna Human-computer Interface Built-in antenna for Modem and test module LED screen and touch screen *1 Indicator light *3 or external antenna Built-in antenna for Modem, test module and WIFI; built-in GPS antenna (optional) Capacitive sensing key*3 on Pilot Scout panel Indicator light *4 Button Power key *1 Power key *1 Capacitive touch panel *1 Interface RJ45 network interface *1 External GPS antenna interface *1 SIM card slot *2 Micro USB interface *1 for development and debugging External GPS antenna interface *1 USB 2.0 extended interface*2 12

13 Appendix Nano SIM card slot *3 Dimension mm mm Weight Around 215 g (with battery) Around 900 g (with battery) In-built Li Battery Rated Voltage: 3.7 V Rated Capacity: 2400 mah Rated Voltage: 7.4 V Rated Capacity: 2000 mah Power Consumption 5.5 W (avg.) 5.5 W (avg.) 18W (max.) Standby Consumption Power 20 mw (powered by battery only) 20 mw (powered by battery only) Battery Performance More than 90 minutes More than 90 minutes Input Power DC 5 V, 2 A 10 to 30 V DC, 2 A Working Current Operating Environment 1.1 A (avg.), 1.6 A (max. internal battery charge) Working temperature: -20 to +50 C Storage temperature: -45 to +85 C Humidity: no more than 93%RH, +40 C 0.75 A (avg.), 1.5 A (max. internal battery charge) Working temperature: -20 to +50 C Storage temperature: -45 to +85 C Humidity: no more than 93%RH, +40 C Bluetooth Yes Yes MOS Yes Yes LTE 2CC-CA testing No Yes LTE 3CC-CA testing No Yes VoLTE testing Yes, one channel Yes, up to 2 channels Note: support additional two channels VoLTE test with external devices in future release POLQA testing No Yes, up to 2 channels Note: support additional two channels POLQA test with external devices in 13

14 Appendix NB-IoT testing Yes Yes future release Test Module Count Up to two test modules 2 dedicated test modules External Device No 2 external devices connect Connection Pilot Watcher Yes Yes Maximum Technology Configuration for Data service Maximum Technology Configuration for VoLTE service 1 LTE modem + 1 LTE test module 1 LTE modem + 2 channels 3CC measurement Note: support additional two channels 2CC measurement with external devices in future release 1 LTE modem + 1 channel VoLTE test 1 LTE modem + 2 channels VoLTE test Note: support additional two channels VoLTE test with external devices in Maximum Technology Configuration for POLQA measurement Does not support POLQA measurement future release 1 LTE modem + 2 channels POLQA measurement Note: support additional two channels POLQA test with external devices in future release 14

15 We have 9 new items listed in the release note document and only 2 here? Please be very careful with this kind of mistakes..release note document is normally made available for customers who have purchased the product, but Datasheet may be used by sales for pre-sales purposes. So this will have a very negative first impression on the product Make sure the details are consistent with what is used in Release note. Release note indicated 2cc/3cc, here its just 3cc? Secondly release note says 16k and 18k samples rate, here 16k and 48k? which is the correct one? This services testing falls under main features, but the amount of services that can be tested seems less than before. Is this correct? Is this correct? A radio chip? can you double check please What about 2CC, should we mention that? Updated and highlighted by Track Changes DINGLI CORP., LTD Address: No. 8, 5 th Technology Road, Gangwan Avenue, Zhuhai, , P.R. China Tel: Fax: support@dingli.com sales@dingli.com DL 5141 DS Dingli DINGLI CORP., LTD Address: No. 8, 5 th Technology Road, Gangwan Avenue, Zhuhai, , P.R. China Tel: Fax: support@dingli.com sales@dingli.com