Make sure that the connector [B] is placed securely as shown above.

Transcription

1 Tray Heater Installation 6. Install the edge clamp [A] and the six clamps. 7. Connect the relay harness [A] to the heater harness [B] ( x 4). 8. Route the relay harness [A] as shown above ( x 3). Make sure that the connector [B] is placed securely as shown above. SM 2-35 M065/M066

2 Tray Heater 9. If you do not install another optional paper feed unit, replace the screw [A] with the screw [B] ( x 1 (M3x8) [C], spring washer x 1 ( 3) [D], washer x 1 ( 3) [E]). Do steps 10 and 11 if you install another optional paper feed unit below M384. If not, go to step Bracket [A] ( x 1) 11. Install the relay harness [A] as shown above. Repeat steps from 1 to 11 if two or three optional paper feed units are to be M065/M SM

3 Tray Heater installed. Installation 12. Rear cover [A] ( x 1). 13. Bracket [A] ( x 1). 14. Connect the relay harness to the relay harness of the mainframe. 15. Reassemble the machine. SM 2-37 M065/M066

4 Tray Heater 16. Attach the on/standby decal [A] to the left-hand side of the main power switch. You can adjust the tray heater switch setting with SP as shown below. 0: Default setting. The heater is on when the main switch is off or when the machine is in energy saver mode. 1: The heater is always on. For Installing the Securing Bracket The securing bracket must be installed when the tray heater is installed in the machine with the paper feed unit (M384). 1. Remove the holder ( p.2-19 "Caster Table (M393)"). 2. Reinstall the inner left lower cover ( x 3). 3. Close the left cover. 4. Remove the left cover of the paper feed unit ( p.2-19 "Caster Table (M393)"). M065/M SM

5 Tray Heater 5. Remove the screw. Installation 6. Install the securing bracket [A] ( x 1 (M3x8) [B], spring washer x 1 ( 3) [C], washer x 1 ( 3) [D]). 7. Remove the right cover of the paper feed unit ( p.2-19 "Caster Table (M393)"). SM 2-39 M065/M066

6 Tray Heater 8. Install the securing bracket [A] ( x 2 (M4x8) [B], spring washer x 2 ( 4) [C], washer x 2 ( 4) [D]). 9. Install the securing holder [E]. 10. Reassemble the machine. M065/M SM

7 Rev. 07/12/2011 Controller Options 2.7 CONTROLLER OPTIONS The following options are available for this machine; refer to the "Operating Instructions: Hardware Guide". Hard Disk Drive IEEE1284 IEEE802.11a/g Gigabit Ethernet Memory Unit Camera Direct Print Card VM Card (Standard in M066) SD card for NetWare printing The following options are available for this machine; refer to the "Operating Instructions: Security Guide". Data Overwrite Security Unit HDD Encryption Unit Installation OVERVIEW This machine has I/F card slots for optional I/F connections and SD card slots applications. After you install an option, check that the machine can recognize it. I/F Card Slots Slot [A] is used for one of the optional I/F connections (only one can be installed): IEEE1284, IEEE802.11a/g, Gigabit Ethernet, SM 2-41 M065/M066

8 Controller Options SD Card Slots Slot 1 [1] is used for PictBridge, Data Overwrite Security Unit, SD card for NetWare printing. Slot 2 [2] is used for installing the VM card or HDD Encryption Unit or one of the optional applications for service only (for example, updating the firmware) SD CARD APPLI MOVE Overview The service program "SD Card Appli Move" (SP5-873) lets you copy application programs from one SD card to another SD card. Do not try to copy the VM card or the HDD encryption unit to another SD card. You cannot run application programs from Slot 2. However you can move application programs from Slot 2 to Slot 1 with the following procedure. Consider the following limitations when you try to merge SD cards. The destination SD card should have the largest memory size of all the application SD cards. Refer to the following table for the memory size of each SD card. Due to limitations, the VM Card (M385) can be neither merged nor moved to another SD card. This card must be installed in Slot 2. Outline of SD Card Appli Move 1. Choose a SD card with enough space. Do not use an SD card if it has been used on a computer. Normal operation is not guaranteed when such an SD card is used. 2. Enter SP5873 "SD Card Appli Move". Then move the application from the SD card in slot 2 to the card in slot Exit the SP mode Use caution when you do the SD Card Appli Move procedure: The necessary data for authentication is transferred with the application program from an SD card to another SD card. Authentication fails if you try to use the SD card after you copy the application program from one card to another card. M065/M SM

9 Controller Options Installation 4. Pull out the paper feed tray. 5. Keep the SD card in the location [A] after you have copied the application program from one card to another card. This is done for the following reasons: 1) The SD card can be the only proof that the user is licensed to use the application program. 2) You may need to check the SD card and its data to solve a problem in the future. Move Exec The menu "Move Exec" (SP ) lets you copy application programs from the original SD card to another SD card. Do not turn ON the write protect switch of an application SD card on the machine. If the write protect switch is ON, a download error (e.g. Error Code 44) occurs during a firmware upgrade or application merge. 1. Turn the main switch off. 2. Make sure that an SD card is in SD card slot 1. The application program is copied to this SD card. 3. Insert the SD card (having stored the application program) in SD card slot 2. The application program is copied from this SD card. 4. Turn the main switch on. 5. Start the SP mode. 6. Select SP "Move Exec". 7. Follow the messages shown on the operation panel. 8. Turn the main switch off. 9. Remove the SD card from SD card slot 2. SM 2-43 M065/M066

10 Controller Options 10. Turn the main switch on. 11. Check that the application programs run normally. Undo Exec The menu "Undo Exec" (SP ) lets you copy back application programs from an SD card to the original SD card. You can use this program when, for example, you have mistakenly copied some programs by using Move Exec (SP ). Do not turn ON the write protect switch of an application SD card on the machine. If the write protect switch is ON, a download error (e.g. Error Code 44) occurs during a firmware upgrade or application merge. 1. Turn the main switch off. 2. Insert the original SD card in SD card slot 2. The application program is copied back into this card. 3. Insert the SD card (having stored the application program) in SD card slot 1. The application program is copied back from this SD card. 4. Turn the main switch on. 5. Start the SP mode. 6. Select SP "Undo Exec". 7. Follow the messages shown on the operation panel. 8. Turn the main switch off. 9. Remove the SD card from SD card slot 2. This step assumes that the application programs in the SD card are used by the machine. 10. Turn the main switch on. 11. Check that the application programs run normally. M065/M SM

11 PREVENTIVE MAINTENANCE REVISION HISTORY Page Date Added/Updated/New None

12

13 Maintenance Tables 3. PREVENTIVE MAINTENANCE 3.1 MAINTENANCE TABLES See "Appendices" for the following information: "User Maintenance Items" Preventive Maintenance SM 3-1 M065/M066

14

15 REPLACEMENT AND ADJUSTMENT REVISION HISTORY Page Date Added/Updated/New 21 01/14/2011 Added step 5 and 6 to Installing the PCDU. 21 ~ 22 08/10/2011 Added step 7 to Installing the PCDU.

16

17 Before You Start 4. REPLACEMENT AND ADJUSTMENT 4.1 BEFORE YOU START Turn off the main power switch and unplug the machine before you do the procedures in this section. Replacement and Adjustment SM 4-1 M065/M066

18 Special Tools 4.2 SPECIAL TOOLS TOOLS Item Part Number Description Q'ty 1 B SD Card 1 2 B PCMCIA Card Adapter 1 3 B USB Reader/ Writer 1 4 VSSM9000 Digital Multimeter - FLUKE G Loop Back Connector - Parallel 1 6 C X Magnification Scope 1 7 A Grease Barrierta S552R Silicon Grease G B Plug - IEEE1284 Type C 1 10 D G104 Yellow Toner 1 Loop back connector - parallel (item 5) requires plug - IEEE1284 type C (item 9). M065/M SM

19 Exterior Covers 4.3 EXTERIOR COVERS LEFT COVER 1. Open the left cover. 2. Remove the waste toner bottle. 3. Release the belt [A]. Replacement and Adjustment 4. Remove the two brackets [A] ( x 2) 5. Left cover [B] SM 4-3 M065/M066

20 Exterior Covers RIGHT COVER 1. Open the duplex unit [A]. 2. Right cover [A] ( x 1) M065/M SM

21 Exterior Covers REAR COVER 1. Rear cover [A] ( x 1) When Reinstalling the Rear Cover Replacement and Adjustment Make sure that these hinge covers [A] can be moved smoothly (up and down) after installing the rear cover. If these hinge covers do not move smoothly, try installing the rear cover again. SM 4-5 M065/M066

22 Exterior Covers TOP COVER 1. Right cover ( p.4-4) 2. Rear cover ( p.4-5) 3. Open the upper cover [A]. 4. Top cover [A] ( x 3) M065/M SM

23 Exterior Covers When Reinstalling the Top Cover Make sure that the hook [A] is installed in the hole [B] when reinstalling the top cover. Replacement and Adjustment SM 4-7 M065/M066

24 Exterior Covers OPERATION PANEL 1. Open the duplex unit ( p.4-4 "Right Cover"). 2. Remove the four screws. 3. Operation panel [A] ( x 1, x 1) M065/M SM