MCC Software installation manual

Transcription

1 MCC Software installation manual MCC Software installation manual EN_05.docx

2 Contents 1 Connection computer MCC Item numbers Jumper setting at the Dongle Version Version Installation of the software Additional functions Request of the in- and outputs Troubleshooting The Toolbox doesn t start The Code status doesn t change from red to green after the code input The window XXXX-XX-XX is not a valid date. pops up again and again No data connection to the MCC possible MCC Software installation manual EN_05.docx

3 1 Connection computer MCC Computer Display cable from MCC Display Dongle Y-Adapter cable Connect the connection cable (USB A) from the dongle with a free USB port of your PC. The other connector (USB-B) is plugged in the dongle. The Y-adapter cable (9- pol.) SUB-D-plug) should be connect to the dongle. Unscrew the display cable at the display and connect the plug of the adapter cable with the M12 plug. This can be done also under power. If necessary the display can be connected to additional M12 connector of the adapter cable. Due to the used plug, an incorrect connection is excluded. Caution when using display and PC together sometimes the display function is slow! Depending on the operating system of the connected computer, the drivers for the dongle from the supplied CD must be installed manually. It is recommended to update to the latest version from the Internet. 1.1 Item numbers Dongle with USB cable => 4920V0025 Y-Adapter cable => 4920R0037 MCC Software installation manual EN_05.docx

4 1.2 Jumper setting at the Dongle Version 1 Jumpereinstellungen: 1-2 connected 3-4 not connected 5-6 connected 7-8 connected 9-10 not connected connected not connected connected not connected connected MCC Software installation manual EN_05.docx

5 1.2.1 Version 2 Jumper settings JP2 (from left to right): JP1 (white) 1-2 connected JP2 (red) 5-6 connected JP3 (white) 8-9 connected JP4 (green) connected JP5 (yellow) connected JP6 (red) connected JP7 (green) connected DIP-switch SW1: 1 Off 2 Off 3 Off MCC Software installation manual EN_05.docx

6 2 Installation of the software System requirement: min. Windows XP The Toolbox requires english Date format (JJJJ-MM-DD)! Troubleshooting see chapter 4.3 To install the software connect the computer to the MCC as described in the chapter 1. The dongle should be coded as described in section 1.2. To install the software package start the file "MCC release X_XX.exe" (XX stands for the current software version, e.g. "MCC release 2_3_672_R.exe"). Click "Next" and select the desired directory path, e.g. "C:\MCC". Click "Next" again to continue the installation. MCC Software installation manual EN_05.docx

7 During the installation, some shortcuts are created on the screen. Doubleclick the shortcut Toolbox Expert to start the programm. Click the button "Set access code" to enter the code. Enter the provided "User code" and "Access code" in the appropriate fields. MCC Software installation manual EN_05.docx

8 After the activation is done automatically the window changes as follows. Save the code with the button "Save". The previous menu appears again. Enter the user code again and confirm with ENTER or OK. MCC Software installation manual EN_05.docx

9 After the activation, the following window appears automatically: Now, the interface must be selected from the computer. In the menu bar under the item "Settings" select the "serial port" marked with MCC. In this example, e.g. "COM4". MCC Software installation manual EN_05.docx

10 The installation is now complete and you can select the desired configuration file (config). For safety reasons the selected config file with the doortype will be shown again. If this is correct it can be confirmed with the "OK"button. MCC Software installation manual EN_05.docx

11 The upload is started by pressing the button "Update MCC". Then appears a short warning message that the existing file on the MCC will be overwriet. This is confirmed with the "OK"button. Now it follows a note which software parts will be upload or updated. MCC Software installation manual EN_05.docx

12 WARNING During the update of the boot software the power of the MCC shoulds not turned off! After activation of the "OK" button, the process will start automatically. After successful completion the following text "MCC system start and ok" appears in the bottom window status display. After the update the service counter should be reset "Restart service period". The softwareupdate or the softwareupload of the new config is now finished. MCC Software installation manual EN_05.docx

13 A full description of the software can be viewed in the menu bar under "Help", or by pressing the F1 key. MCC Software installation manual EN_05.docx

14 3 Additional functions 3.1 Request of the in- and outputs The state of the in- and outputs from the power and assembled MCC can be checked with the "Status" button. Green dot means 24 V power and red dot means 0 V. To display the right values of the config please download the config before checking. At the same time the programmed function of inputs and outputs can be read. E.g. X 15 = > input = down, output = 24 V MCC Software installation manual EN_05.docx

15 4 Troubleshooting 4.1 The Toolbox doesn t start Each Toolbox version has got a fixed time stipulated periode of use. After the expiration date, the software version is invalid and can no longer be used with the old code! Each registered Toolbox user gets together with the new code automatically in due time before the expiry of the old version via a link to download the new software. If there no new version of the software, only a new access code will be sent. The old code can no longer used. 4.2 The Code status doesn t change from red to green after the code input Is the latest version of the software installed? The new code works not for old versions but only for the current! Download and install current software version The User code has been entered incorrectly Validity date, here till Please compare the spelling with the . Enter the "User Code" in lowercase (possibly operated caps-lock button note!) During the initial installation of the Toolbox, it can happen that the first code is not accepted. After entering the first code and pressing the ENTER key delete the code and enter the second code from the . MCC Software installation manual EN_05.docx

16 4.3 The window XXXX-XX-XX is not a valid date. pops up again and again The set date format is incorrect! Exit the Toolbox in the task manager of Windows and change the date format in Control Panel ("Regional and Language Options") to the date format "YYYY-MM- DD". Then start the Toolbox and enter the code again. 4.4 No data connection to the MCC possible An existing data connection will be shown in the Toolbox window as a green dotted line. Due disconnect connection the line is missing. Existing data connection An disconnected or interrupted connection can have the following reasons:: - The cables and plugs are not corrected in the right way. - The MCC control unit is turned off MCC Software installation manual EN_05.docx

17 - The jumper in the dongle are not adjusted in the right way (see chapter 1.2) - Install if necessary the driver of the dongle manually. - A wrong interface connection is selected (Toolbox => Settings => Serial port => select COM-Interface with MCC in brackets behind). - At Toolbox => Settings => At Modbus/Bluetooth adapter no hook should be set! - At Toolbox => Settings => At Auto connect a hook should be set! MCC Software installation manual EN_05.docx