VUE 2 App Version VUE2 User Manual. VUE 2 App Version

Transcription

1 VUE2 User Manual VUE 2 App Version

2 Contents Introduction 3 Prerequisites. 3 Getting started.3 WiFi Set-up....4 Setting up your fiber inspection microscope and VUE2..6 Inspecting Fiber Ends and Analyzing Captures 10 VUE 2 App Version

3 Introduction: Congratulations on your purchase of SENKO Smart Probe Video Microscope with Automated IEC End-Face Inspection App, which has been developed to provide the best reliability and performance. The VUE2 provides end users with a comprehensive and effective field portable solution for the inspection of optical interfaces. The VUE2 provides the capability to inspect and analyze the end face of fiber optic connectors for contamination and other defects. To get the best use of the VUE2 + Smart Probe and ensure its safe operation, please take few minutes to read this manual. Prerequisites: Android Lollipop Version 5.0 (API Level 21) Adobe Acrobat Reader Getting Started: Install VUE2 App Download VU2 from Google play (Search for Senko VUE2). Install Adobe Acrobat Reader Download Adobe Acrobat Reader from Google Play. + VUE 2 App Version

4 WiFi Set-up: Once VUE2 App has been installed on the device, launch the app & switch on the Smart Probe. Message will appear Cannot connect to Smart Probe. Open Wi-Fi Settings? Select Yes to connect VUE2 App with the Smart Probe. In WiFi Settings, Select the Smart Probe SSID (prefixed with SPxxxxx) VUE 2 App Version

5 Tap the SSID and enter the password Tap Back button on your device to return to the app. The WiFi connection will now show as connected VUE 2 App Version

6 Setting up your fiber inspection microscope and VUE2: The app will open the following screen. The following diagram explains the various functionality in the app: Tap the User Name button to set the name of the operator, followed by OK (or Cancel to leave unchanged) VUE 2 App Version

7 Tap the Location button to set the location of the fiber being tested (Press OK to set, or Cancel to leave unchanged) The Settings button allows the operator to change the following: a. Enable/Disable Sounds. b. Create a PDF report each time the Capture button is pressed. c. Create an image of the end-face each time the Capture button is pressed. VUE 2 App Version

8 Press the Mode button to select the type of connector being tested. The mode button will then select mode. Inspection Mode SM-APC-M (Patchcord) SM-APC-F (In-adapter) SM-UPC-M (Patchcord) SM-UPC-F (In-adapter) MM-UPC-M (Patchcord) MM-UPC-F (In-adapter) Example Connector Types SC, FC, ST, LC, MU, DIN, MPO(View only) SC, FC, ST, MU, DIN, MPO (View only) SC, FC, ST, LC, MU, DIN, MPO (View only) SC, FC, ST, LC, MU, DIN, MPO(View only) SC, FC, ST, LC, MU, DIN, MPO (View only) SC, FC, ST, LC, MU, DIN, MPO (View only) VUE 2 App Version

9 Once inspection mode has been selected, adjust the focus by turning the focus wheel on the Smart Probe to obtain good image quality. The Image Quality Meter can be used as a reference point to obtain high quality image. In addition the focus indicator, which is displayed in the left part of the window, indicates whether the current view is optimized for a capture. A green indicator shows a picture that can be captured and analysed. Analysis will be more difficult with a blue indicator, and impossible with orange indicator. Poor Focus (Example) VUE 2 App Version

10 Inspecting Fiber Ends and Analyzing Captures: For inspection of fiber end-face, adjust focus (Image quality at least 80%) and press the Process button. After few seconds the image will be analyzed and any defects will be highlighted in red. Tap the Info Panel (in this case where the result is displayed as PASS). This will display a table of defects found, based on each Zone. VUE 2 App Version

11 To access the PDF report created by the app, tap the PDF Folder button (To return to the main screen, press the device Back button) Open the appropriate report by tapping it. The Report filename is structured as follows: a. SP_yyyymmddhhmmss_OperatorName_Location.pdf i. yyyy = Year ii. mm = Month iii. dd = Day iv. hh = Hour v. mm = Minute vi. ss = Second vii. OperatorName = The name of the operator entered in the User Name dialogue. viii. Location = The location entered in the Location dialogue VUE 2 App Version

12 b. An example PDF report is shown below: To access the analyzed images created by the app, tap the Image Folder button (To return to the main screen, press the device Back button): VUE 2 App Version

13 To view the full filename of the image, it is recommended to view using the Details view as follows: Note: The captured images & PDF report can be exported from the app and uploaded to the if need be VUE 2 App Version