164.73mm 6.49in mm 5.55in. Spingarde. Sht 1 of 8 Shts. Sht Size A2. All dimensions in mm and (inches) 3rd Angle projection

Transcription

1 164.73mm 6.49in mm 5.55in Sht 1 of 8 Shts Sht Size A2 Spingarde

2 16 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 Wheel 2 2 Carriage Frame Base 1 3 Main Support frame 1 4 Carriage angular adjuster Barrel 1 6 Breech Block 1 7 Handle 2 8 Support pin X 18 9 Pivot Pin 2 10 Wheel Shaft 2 11 Taper pin 2 12 Barrel Support 3 13 Cannon alignment block Cord Hanger 4 15 Tie down Rope 2 4 X Roof 1 Ridge Beam 1 Panel Support-middle 2 Panel Support-front 2 Panel Support-Back 2 Panel Panel-2 1 Panel X Panel-4 1 Panel-5 1 MirrorPanel-1 1 MirrorPanel-2 1 MirrorPanel-3 1 MirrorPanel-4 1 MirrorPanel-5 1 Roof Rod Rear 1 Roof Support-Front 1 Roof Ridge Bead 1 17 Arrow Size 0 Csk Screw 8 19 Carriage Gimbal Carriage Pivot 1 Gimbal Pivot 1 Gimbal Pin 1 20 Spanner 1 11 All of the larger componets are wood and the choice is down to your own preference. The small fittings and the gimbal can be made from brass or copper wire and sheet and painted or plated. The cord to tie the barrel to the frame is nylon. 1 Sht 2 of 8 Shts Sht Size A2 Spingarde

3 100mm 3.94in 1mm 0.04in A 2mm 0.08in 4mm 0.16in 5mm 0.20in 16 Ø2 pegs to secure spokes 20mm 0.79in 44mm 1.73in 16mm 0.63in R22mm 0.87in VIEW B 81.05mm 3.19in R185.54mm 7.30in A 7.50mm 0.30in SECTION A-A Metal band fixed around the wheel 30 B 10 holes Ø 5mm 2.5 spacing 20mm 0.79in 1 Wheel 2 required 1:1 Scale R175.54mm 6.91in 1 Carriage angular adjuster 1 required 1:1 Scale 3 R165mm 6.50in 2 CarriageFrame Base 1 required 1:1 Scale 9.80mm 0.39in 3 8 Sht Size A2 Spingarde

4 mm 2.36in SECTION F-F 20mm 0.79in 36mm 1.42in 9mm 0.35in TRUE R160mm 6.30in F F 75mm 2.95in 44mm 1.73in mm 0.20in 50mm 1.97in 50mm 1.97in mm 8.82in Ø2mm pegs each side 36 P 3 Main Support Frame 1 Required R32.20mm 1.27in VIEW P 4 8 Sht Size A2 Spingarde

5 mm 1.20in G 24.50mm 0.96in 4mm 0.16in 270mm 10.63in 15 G 20mm 0.79in 12.50mm 0.49in 60mm 2.36in 23mm 0.91in 5 Barrel- 1required 25mm 0.98in 63.46mm 2.50in 84mm 3.31in H 26mm 1.02in 14mm 0.55in 18mm 0.71in 26mm 1.02in 14.99mm 0.59in 19.56mm 0.77in 73.08mm 2.88in SECTION G-G 48mm 1.89in 13.40mm 0.53in 11mm 0.43in 27mm 1.06in 0.50mm 0.02in J 3.20mm 0.13in 29mm 1.14in DETAIL H SCALE 2 : 1 3/4 inch Acme Thread 6 tpi I I 13.60mm 0.54in 19.05mm 0.75in J SECTION J-J SECTION I-I Breech Block- 1 required 3/4 in acme thread 6tpi 5 8 Sht Size A2 Spingarde

6 16mm 0.63in 29mm 1.14in 14.50mm 0.57in 1.50mm 0.06in 50mm 1.97in 5mm 0.20in 4mm 0.16in 9 Pivot Pin - 2 Required 14.28mm 0.56in R5.50mm 0.22in 8 Support Pin - 1 Required 7 Handle - 2 Required 16mm 0.63in 7mm 0.28in 45mm 1.77in mm 0.13in 11 Taper Pin - 2 Required 32mm 1.26in R11.50mm 0.45in 32mm 1.26in R13.50mm 0.53in 10 Wheel Shaft - 2 Required 4mm 0.16in 17.75mm 0.70in 9.50mm 0.37in 7mm 0.28in 12 Barrel Support - 3 Required 9mm 0.35in 13 Cannon alignment block - 1 Required 3.20mm 0.13in 30 14mm 0.55in 270mm 10.63in 17 Arrow - 2 Required wire 0.06 R14.75mm 0.58in swg plate brazed to wire Two holes drill and csk for No 0 screw 14 Cord hanger - 4 Required 20 Spanner - 1 Required Sht 6 of 8 Shts Sht Size A2 Spingarde

7 2mm 0.08in 14mm 0.55in 19 Gimbal pin 1 required 24mm 0.94in 11mm 0.43in Press fit 19 Gimbal Pivot 1 required 21.15mm 0.83in mm 6.13in 14mm 0.55in 44mm 1.73in 0.39mm 0.02in 9.80mm 0.39in mm 0.05in mm 2.54in R7mm 0.28in R9mm 0.35in 40mm 1.57in Carriage pivot flattened 40mm 1.57in R 16mm 0.63in 19 Carriage Pivot 1 required 48.76mm 1.92in 7 8 Sht Size A2 Spingarde

8 Roof Ridge Bead 50mm 1.97in 5mm 0.20in K mm 3.15in 80 VIEW K 12.69mm 0.50in 43.70mm 1.72in Cut out to clear wheels Roof 1 Required Roof panels scale 1:1 2 sets required-trim on assembly VIEW M 95mm 3.74in 95mm 3.74in 1.50mm 0.06in O M O mm 0.22in SECTION O-O Ridge Beam 1 Required Sht Size A2 Spingarde