INSTALL INSTRUCTIONS PT-VIDEO-1, 2, 3, or 4 PT-VIDEO-MDVR PRISONER TRANSPORTATION VIDEO SYSTEM
|
|
- Beryl Barber
- 5 years ago
- Views:
Transcription
1 INSTALL INSTRUCTIONS PT-VIDEO-1, 2, 3, or 4 PT-VIDEO-MDVR PRISONER TRANSPORTATION VIDEO SYSTEM TOOLS REQUIRED: Powered Drills (3/8 & ½ ) 4 ½ Hole Saw or Jig Saw Drill bit Set Wire Stripping Tool Wire Crimping Tool Standard Socket Set Ratcheting Wrench HARDWARE: QTY DESCRIPTION PART # 2/4/6/6 #10 x ½ Flat head machine screw GSM /4/6/6 #10 Keps nut GSM /6/9/9 #10 x ¾ Flat head sheet metal screw GSM33151 COMPONENTS: QTY DESCRIPTION PART # 1 Panavise Monitor mount bracket GSM Voyager 7 LCD Monitor GSM /2/3/3 6 Round ¼ Lexan cover HS-SH /2/3/3 Camera mounting bracket KKM /2/3/4 Voyager 25 ft. Camera cable GSM Voyager Camera Adapter cable GSM /2/3/3 Interior Bullet camera GSM Per (-4 only) Optional Rear External Camera GSM Per (-MDVR) RCA to RCA 6 ft. cable GSM Per (-MDVR) RCA to adapter cable GSM70026 Always! Read all instructions before installing any Havis-Shields Equipment Corp products. Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes! Use hardware provided with install kit For product support, visit the Install Instructions Section of our website at technicalsupport@havis.com or call
2 SUB ASSEMBLY: 1. Confirm receipt of all components and hardware. 2. Read all instructions before installing any Havis-Shields Equipment Corp products. INSTALLATION: 1. Drill/Cut Holes into Ceiling of Kwik Kit: (see photo 1 & 2 on following page) Location of camera to be determine by installer/customer depending on specific application RECOMMENDED CAMERA LOCATIONS: (See following photos) RECOMMENDED CAMERA LOCATIONS Driver Side Compartment of Kwik Kit Photo 1 ½ Powered Drill w/ 4 ½ Hole Saw Photo 2 Divider Wall Front Bulkhead Forward section of ceiling. Close to divider for bench visibility. 3 rd Compartment-Mount camera on forward side close to side-door frame.. CAUTION: Do not drill into overlap on ceiling sections. Beware of wiring, power-vents, etc. Take caution when drilling 4 ½ hole to not hit roof of vehicle. Drill one 3/16 pilot hole on this measurement in one of the compartments. Using a hole saw drill 4 ½ hole at this location. Check for fit of Camera assembly then proceed with cutting holes for remaining cameras. 2. Route Camera Cables: Route 25 (foot) lengths of camera cable to each of the holes previously drilled. Tie camera cables so they don t rattle on ceiling of Kwik Kit. Cables will eventually connect to camera after camera is assembled to bracket. 3. Assemble Camera(s) to Camera Bracket(s): (see photo 3) Separate Camera from nut and spacer. Slide camera into hole of metal bracket. 2
3 Re-attach spacer and nut and completely tighten being sure red arrow on back of camera is pointing up. Mount camera to clear lexan cover using (2) #10 x ½ Flat head machine screws and # 10 keps nuts. Sub assembly of Camera bracket to ¼ Lexan cover Photo 3 (2) x ½ Flat Head Screws 4. Wire Voyager system: Wire system according to manufacture recommendations included within video system component boxes and the wire diagram supplied in this instruction. Mounting location of Control and Junction box is to be determined by the installer/customer but recommended on the belly pan inside the Consolidator Console. Mounting location of the Monitor, and Remote is to be determined by installer/customer but recommended on the Consolidator Console using #10 x ½ machine screws and keps nuts. (See photo 4 & 5) Possible Monitor mounting solution Photo4 Photo5 3
4 5. Mount Camera assembly to Kwik Kit Ceiling: (See photo 6) Plug camera cable into one of the camera assemblies. Turn on system. Position camera to obtain optimal visibility within the compartment. You will need two people for this step. Mark mounting holes on ceiling. Pre-drill holes with 1/8 pilot. Reposition camera assembly and mount using #10 x ½ Flat head sheet metal screws. Repeat steps for remaining cameras. Test system. View of 3 rd compartment setup 3 rd Compartment Door Frame Photo 6 (3) #10 x ¾ Flat Head Sheet Metal Screws Front Bulkhead 4
5 6. PT-VIDEO-4 Components: Mount external camera in desired location. If being used for viewing when backing up install camera on backside of roof as close to center as possible. (See photo 7) PT-VIDEO-4 External Camera Photo7 7. PT-VIDEO-MDVR (Optional): See wiring diagram and instruction manual ( provided with MDVR ) for complete details. Mount Digital recorder control head into the supplied equipment bracket # C-EB25-MMT-1P. This will allow mounting of console into desired location of HSEC console. 5
6 Note: Wiring diagram is also included with the monitor 6
DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL
DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL Version 2.1 June 4, 2013 0 Table of Contents Low Profile Pan Tilt Kit Description... 3 Low Profile Pan Tilt Unit Basic Operation... 4 Mounting
More informationINSTALLATION MANUAL. LO SIDE BOX ADD-ON KIT For driver or passenger side configurations TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK
TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL LO SIDE BOX ADD-ON KIT For driver or passenger side configurations Model: QDKSBDO1 -or- QDKSBP01 Part No. 24-0327 Rev. A ECN 5430 ATTENTION:
More informationC764i Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
C764i Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 3 Obtaining Service... 3 Unpacking the Equipment... 3 Important
More informationGMT INC. EZGO Radio Console Present Section I Installation Preparation. Part Number: EZ40X-X Section I Installation Preparation Kit Contents
Part Number: EZ40X-X Kit Contents Quantity Reqd. Color Applicability/Trim Level Description Radio Console Left Mounting Bracket Right Mounting Bracket Accessory Color Item # 2 3 Vehicle/Trim Color All
More informationTECHKNOW, INC. Kiosk Order Confirmation System INSTALLATION MANUAL. Revision Date: July 11, 2012 Part # Version 3.2
document Page 1 of 18 TECHKNOW, INC Kiosk Order Confirmation System INSTALLATION MANUAL Revision Date: July 11, 2012 Part # Version 3.2 Techknow, Inc. 393 Mayfield Road Duncan, SC 29334 www.gotechknow.com
More informationHavis Integrated Control System Installation Instructions for Standard* Ford Police Interceptor Utility
Installation Instructions for Standard* Ford Police Interceptor Utility Does not properly fit instrument panel in an Interceptor Utility with Interior Upgrade Code 65U Upgrade Package Includes: Cloth Seats
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationM-2300-ZX Focus SVT Brake Conversion Kit INSTRUCTION SHEET
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: This kit is designed
More informationINSTALLATION INSTRUCTIONS
2015 F-150 8 MyTouch factory display 360º Vision System (Kit # AVMS-3618) DUE TO THE COMPLEXITY OF THIS KIT PROFESSIONAL INSTALLATION IS REQUIRED CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING -Must
More informationSNOWBOARD RACK KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 25
SNOWBOARD RACK KIT P/N 2881251 APPLICATION Pro Ride RMK 155 and 163, Axys RMK 155, 163, and 174 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationPARTS DESCRIPTION LISTING
PARTS DESCRIPTION LISTING Form 4-157e, 11-09 Sheet 2 of 6 Index No. Part Number Description A 16-889-1 TUBE ASSEMBLY, CAMERA SUPPORT CM (See Sheet 5) B 69-1063-1 COVER, ASSEMBLY BACK DSP600 (See Sheet
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND
ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND E062324 ELO-STAND-SELF-SERVICE-DESKTOP E062510 ELO-STAND-SELF-SERVICE-FLOOR EXT E062704 KIT-EMV-CRADLE-VF-MX915-ING-ISC250 E062899 KIT-EMV-INGENICO IPP350
More informationBasketball Shot Clock Set LX2180 Manual
Basketball Shot Clock Set LX2180 Manual 72 Industrial Boulevard Wrightsville, GA 31096 Phone: (800) 445-7843 Fax: (800) 864-0212 www.electro-mech.com LX2180 Revision 5 February 8, 2013 Table of Contents
More informationPracticeWire. Field Support: Page 1
PracticeWire Field Support: 1-877-233-9114 Page 1 Table of Contents Required Tools Page 3 Software Hardware 1) Admin Login.... Page 3 2) Checking AT&T signal strength Page 3 3) Port test.. Page 4 1) Cradlepoint
More informationEaton LCD Lift Flat Panel Display System. Installation Guide
Eaton LCD Lift Flat Panel Display System Eaton LCD Lift Flat Panel Display System Installation Guide Copyright 2011 Eaton Corporation, Worcester, MA, USA. All rights reserved. Information in this document
More informationGCX Mounting Assembly Installation Guide. Pedestal Mount for Philips IntelliVue MP5/20/30/40/50/60/70, MX400/450/500/550/600/700/800
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com GCX Mounting Assembly Installation Guide Pedestal Mount for Philips IntelliVue MP5/20/30/40/50/60/70, MX400/450/500/550/600/700/800
More informationInstallation Guide. Universal Camera Mount Bracket
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Universal Camera Mount Bracket The purpose of this guide is to describe the assembly and
More informationThe Indoor+Outdoor Security Starter Kit Quickstart Guide
What s inside: The Indoor+Outdoor Security Starter Kit Quickstart Guide 1x Security Shuttle 1x Mini Cube HD camera 1x Mini outdoor Full HD camera 2x Door + Window sensors 1x Keychain remote 2x Power adapters
More informationInstallation Guide GE Healthcare Solar 8000M Keypad Mounting Kit for 15'' and 18'' Flat Panel Displays
Installation Guide GE Healthcare Solar 8000M Keypad Mounting Kit for 15'' and 18'' Flat Panel Displays The purpose of this guide is to: 1. Describe attachment of Keypad to Keypad Mounting Bracket (page
More informationCycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 4 Obtaining Service... 4 Unpacking the
More informationCharging Cabinet Owner s Manual
by edugear Charging Cabinet Owner s Manual Before using, please read these operating instructions carefully. They contain important advice concerning the use and safety of your Charging Cabinet. The Charging
More informationLARGE S URGE-PROTECTOR S HELTER
LARGE S URGE-PROTECTOR S HELTER The weather-resistant Large Surge-Protector Shelter (simply referred to as the shelter in this manual) provides protection from the elements for Surge Protectors (not included)
More informationCoin Acceptors, Inc. Installation Instructions for the 4.3 Touch Screen Display
Coin Acceptors, Inc. Installation Instructions for the 4.3 Touch Screen Display Kit # 410930 and 410930-1 DN3800 and DN5800 Publication 928412 1 Hand Drill Utility Knife Step Ladder 5/8 Drill Bit Tools
More informationKRONOS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TABLE OF CONTENTS ENCLOSURE AND DONGLE ASSEMBLY 1 LIGHTED ENCLOSURES 2-10 2 SLIM ENCLOSURE 11-17 3 WIRED-ETHERNET DONGLE 18-25 4 REAR-OFFSET MOUNT 26-33 5 SIDE-MOUNT 34-41 6 SURFACE
More informationSystem Storage EXP3000 Rack Installation Instructions
System Storage EXP3000 Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When you install the IBM System Storage EXP3000 in a
More informationModel: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features
Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Fully Adjustable, Multiple Viewing Angle Smart Camera. High Resolution, 1/2 CMOS Color Camera
More informationTools required: 1. 10mm combination wrench 2. 10mm socket, 6 + extension, and ratchet. 3. Torque Wrench ( in. lbs.) (11-18 ft. lbs.
This tutorial will show you how to replace your weak factory Relay Lever Driver (1J0-711-256) with an upgraded Grüvenparts Cable Transmission Short Shift Kit. This procedure will only take about 5 minutes
More informationINSTALLATION MANUAL DATAVAULT DATAVAULT - BARE JOBSITE STORAGE SOLUTIONS
JOBSITE STORAGE SOLUTIONS ALWAYS ON THE JOB INSTALLATION MANUAL 118-01 DATAVAULT 118-02 DATAVAULT - BARE Werner Co. 724-588-2000 93 Werner Rd. 888-523-3371 toll free/ llamada gratuita Greenville, PA 16125
More informationINSTALLATION MANUAL DATAVAULT DATAVAULT - BARE JOBSITE STORAGE SOLUTIONS
JOBSITE STORAGE SOLUTIONS ALWAYS ON THE JOB INSTALLATION MANUAL 118-01 DATAVAULT 118-02 DATAVAULT - BARE Werner Co. 724-588-2000 93 Werner Rd. 888-523-3371 toll free/ llamada gratuita Greenville, PA 16125
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationInstallation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL)
Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL) Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the paint)
More informationCOMPLETE S YSTEM SHELTER
COMPLETE S YSTEM SHELTER The weather-resistant Complete System Shelter (CSS) provides protection from the elements for system components such as the console, Solar Power Kit components, sensor interface
More informationFLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N
FLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N 5-0083-00 TOOLS REQUIRED - 3/4" SOCKET - 3/4" WRENCH - /3" WRENCH - PHILLIPS SCREW DRIVER - TORQUE WRENCH INSTRUCTION P/N 6-0083-00 ISSUED: 3//7 SHEET
More informationINSTRUCTIONS PARTITION INSTALLATION.
2015 FORD 2015 TRANSIT FORD LOW PARTITION ROOF INSTRUCTIONS PARTITION INSTALLATION INSTRUCTIONS www.sortimo.knapheide.com 1 The following instructions detail the procedure for installing a Sortimo By Knapheide
More informationInstallation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit
Installation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter on Arm (page 2). 2.
More informationNavigator II INstallatIoN MaNUal For static and PaN/tIlt configurations
Navigator II Installation MANUAL For Static and Pan/Tilt Configurations Document Number: 432-0001-00-12, rev 100 FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole
More informationINSTALLATION INSTRUCTIONS Version 2.4
INSTALLATION INSTRUCTIONS Version 2.4 11/12/2012 Patient Point, LLC 8230 Montgomery Road, Suite 300 Cincinnati, Ohio 45236 1-800-287-0908 TABLE OF CONTENTS System Overview 2 Tool List. 3 Installation Process
More informationPrint Mechanism Maintenance Kit
Print Mechanism Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the print mechanism maintenance kit in the following printers: ZT0 ZT0 ZT0 Read
More informationCREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual
CREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual Part No. This page intentionally left blank Table of Contents INTRODUCTION...5 Tools Required...5 Credit Card Reader
More informationInstructions for installing your QuiltCam on your Gammill quilt machine.
Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationDMD Extender. Application Note 1 Sega Large Screen LCD Replacement. V0.1 October 2013 Copyright 2013 Dr Pinball
DMD Extender Application Note 1 Sega Large Screen LCD Replacement V0.1 October 2013 Copyright 2013 Dr Pinball Important This document is a guide to installing an LCD panel to replace a plasma display in
More informationInstalling the DX LCD Display
DX LCD Display User s Guide 3-1 Chapter 3 Installing the DX LCD Display Introduction Use the DX LCD Display as either a portable device, or permanently mount it in a panel or on the wall. For panel and
More informationParts and Service Manual IMCO
XXTREME ADVANTAGE Gimbal Parts and Service Manual IMCO 510 East Arrow Highway San Dimas, CA 91773 (800) 899-8058 (909) 592-6162 Fax (909) 592-6052 www.imcomarine.com email info@imcomarine.com TABLE OF
More informationGM NBS Truck CCD Backup Camera Kit Installation Guide
CS GM1 GM NBS Truck 2007 2012 CCD Backup Camera Kit Installation Guide Thank you for your purchase! These instructions are intended for the do it yourselfer who decides to install the camera without professional
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationAssembly Instructions
Assembly Instructions Flat Screen Garage End User & IT Computer Cable Management May 2013 nylon zip-tie #2 (for computer wires) rear-access beam door (open) Figure 1 nylon zip-tie #1 (for #1 motor control
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More informationMotorized Ceiling TV Mount
Motorized Ceiling TV Mount Instruction Manual SKU: MOUNT-E-FD55 Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/mount-e-fd55
More informationCU-8R Installation Instructions
CU-8R Installation Instructions I. Components Model CU-8R is shipped with the following components: QTY Item 1 Stainless Steel Enclosure 2 Lexan Panels 18 Nuts 1 Wall Mount Style Phone with RJ-11 Cable
More informationInstallation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationMounting Accessory Guide
Apr. 12 2010 Table of Contents Mounting Accessory Guide 1 Overview 5 Introduction... 5 Types of Mounting Methods... 5 Surface... 5 Wall... 5 L-Type Wall Mount (PMAX-0308) 6 Heavy Duty Wall Mounts (PMAX-0305
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationPowerView Model PV485. Installation Manual Section 78
PowerView Model PV485 Installation Manual 00-02-1018 2017-05-23 Section 78 In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our specifications
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Chrysler/Dodge/Jeep Remote Add-On CD player for RA1, RA2, RA3, or RA4 radios (Kit # 5000-8750) 2013-current RAM truck and Viper; 2015-current Charger, Challenger, and 300; 2017 Pacifica Please read thoroughly
More informationAssembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #
Assembly Instructions Triton Enclosure for Poseidon With Data Acquisition November, 2007 V0.9 DSC Document #7521002 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationDirectCommand Installation 5 Channel Spreader Control Module Technology
DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100582 1 Cable Installation
More information*000IPODIG* ipod Installation Guide. Tools Needed: (depending upon vehicle) 000IPODIG IMPORTANT
Revision 3/15/05 ipod Installation Guide IMPORTANT Before starting, compare items on your invoice with items received. Carefully check through packaging material. If any item is missing, please call: Crutchfield
More informationGalaxy Rectifier Shelf Field Replacement
Galaxy Rectifier Shelf Field Replacement Model PWRSYS-RFK-A203 Installation Guide Galaxy Rectifier Shelf Field Replacement Model PWRSYS-RFK-A203 Installation Guide, Part Number 139691-1 Copyright 2011,
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationA-dec 586 Ceiling Monitor Mount
Installation Guide A-dec 586 Ceiling Monitor Mount Recommended Tools 7/16" wrench Socket set and ratchet with 6" extension Phillips head and standard screwdrivers Diagonal cutters Level 3/8" drill with
More informationDisconnect the battery to ensure there will be no shorted wires during the installation procedure.
The round-style headunit receiver radio features Bluetooth technology allowing music to wirelessly stream from your compatible Bluetooth-enabled device. Control the audio from a distance -- all from your
More informationARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios.
Required for Install: ARC-CDJPLAYER INSTALLATION MANUAL Full plug and play kit, universal fit for use in Chrysler vehicles with RA1, RA2, RA3, or RA4 radios. 1. Chrysler/Dodge/Jeep vehicle with Uconnect
More informationTreadmill Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Treadmill Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 Before You Begin... 4 Obtaining Service... 4 Unpacking the Equipment... 4 Important
More informationLANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS
LANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS Navigation (MMCS) unit Camera Thank you for purchasing the Mitsubishi Genuine Accessory. To install
More informationThe QSR kitchen video bracketing options can be assembled to fit your specific kitchen environment needs.
QSR Kitchen Video Bracket Configurations and Instructions The QSR kitchen video bracketing options can be assembled to fit your specific kitchen environment needs. A variety of mounting solution configurations
More informationDual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines Installation Instructions (Kit # )
Please read thoroughly before starting installation and check that kit contents are complete. Items Included in Kit: Chassis Harness Power Harness with RCA connectors Camera mounted on license plate bracket
More informationSPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS
SPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS (WITH CAPACITOR CHARGER BOARD A3517-02) The process depends on Generator and System configuration. This document applies to installation of Capacitors
More informationBullet Camera Installation in an Outdoor Enclosure
Bullet Camera Installation in an Outdoor Enclosure This document explains how to install a Bullet Camera into an outdoor enclosure. Step 1: Install the Wi-Fi Antenna (Optional) If you will be installing
More informationRemote Control Motorized TV Ceiling Mount
INSTALLATION MANUAL Remote Control Motorized Ceiling Mount CAUTION: DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR! DEHA-400E 15 200x200 300x300 400x200 400x400 55" MAX
More informationReplacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638
Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638 This kit contains detailed instructions on removing a Galaxy II Daewoo monitor and replacing it with a 19 wide flat screen monitor.
More informationPandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006
Pandora Assembly Instructions With Diamond Systems PC/104 CPUs (Athena, Elektra and Prometheus) November, 2006 Diamond Systems Corp. (650) 810-2500 www.diamondsystems.com This document describes how to
More informationAssembly Guide T9200, T9500, T9600, AND T9700 PLATFORM TREADMILLS
Assembly Guide T9200, T9500, T9600, AND T9700 PLATFORM TREADMILLS Assembly Guide T9200, T9500, T9600, AND T9700 PLATFORM TREADMILLS To avoid possible damage to this Platform Treadmill, please follow these
More informationUltra short throw lens installation
Ultra short throw lens installation The ultra short throw lens 0.36 UST GS (P/N: 140-133108-XX) allows you to position your projector as close as possible to your screen or display. Unless otherwise indicated,
More information7" Touch Screen Display
7" Touch Screen Display Installation Guide Contents Minimum Requirements...1 Select a Location...1 Initial Setup...2 Unboxing...2 Installation...3 Prepare the Panel...3 Install the Mounting Plate...3 Mount
More informationAg Leader Technology. DirectCommand Installation RoGator Model Years
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100550 1 Dual Lock 2000052-9 1 Dual Lock 2000053-9 1 Hardware Kit
More informationLINEAR ACTUATOR CONTROL Use with NEW LEADER 7 manual
MANUAL FOR MODEL LINEAR ACTUATOR CONTROL Use with NEW LEADER 7 manual INSTALLATION OPERATION TROUBLESHOOTING PARTS LIST This unit may have been built with SPECIAL FEATURES. Provide SERIAL NUMBER when ordering
More informationCutter Option Installation Instructions
This kit includes the parts and documentation necessary to install the cutter option on the Zebra XiII, XiIII, and XiIIIPlus-Series printers. NOTE: The Cutter Option is not available for the 96XiIII. Adding
More informationOPERATING INSTRUCTIONS:
List OPERATING INSTRUCTIONS: Preparation For Installation, Product Identification Charging The Batteries ing And Adjusting The Lift Mounting Head s Brackets Mounting Clamps And Quick-Locking Arms Installation
More informationGeneral Information. Installation Instructions. 3S-4000 Folding Min-Till Drill Acre Counter Update. Used with: 3S-4000
Installation Instructions 3S-4000 Folding Min-Till Drill Used with: 3S-4000! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the
More informationINSTALLATION INSTRUCTIONS
Design and Assembly Envisor components are designed to function as an Equipment Screening System. Modular by Design allows for a more user-friendly installation. This instruction packet is intended to
More informationSITRANS F. Flowmeters SysCom Upgrade Kit IP65 (NEMA 4X) Multi-Channel. Introduction 1. Installing/Mounting 2. Hardware Installation Instructions
Introduction 1 Installing/Mounting 2 SITRANS F Flowmeters SysCom Upgrade Kit IP65 (NEMA 4X) Multi-Channel Hardware Installation Instructions 1/2010 A5E02518333A Revision 04 Legal information Warning notice
More informationWarning Before Installation. Package Contents EN - 1. Refer to your user's manual for the operating temperature.
510000221G Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or
More informationTracKing for Precedent Single Temperature and Multi-Temperature Installation Instructions
TracKing for Precedent Single Temperature and Multi-Temperature Installation Instructions Item Description Part Number Qty. Kit 401386 Single Temp Units Kit 401378 Multi-Temp Units 1. Bracket, Antenna
More informationCONVERGE Pro 2 GPIO Expander A General Purpose Input and Output Expander unit for CONVERGE Pro 2. Quick-Start Guide
CONVERGE Pro 2 GPIO Expander A General Purpose Input and Output Expander unit for CONVERGE Pro 2 Quick-Start Guide Table of Contents CONVERGE PRO 2 GPIO EXPANDER... 1 UNPACKING... 1 Parts Included... 1
More informationDirectCommand Installation RoGator Model Year Ag Leader Technology
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100801 1 Dual Lock 2000052-9 1 Dual Lock 2000053-9 1 Quick Reference
More informationAdapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout
Installation Instructions Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Catalog Numbers 2711-NR5T, 2711P-RAT12E2 Topic Page About This Publication 1 Important User Information 2 About
More informationPromaster Chassis Cab and Cut Away Loose Ship Back Up Camera System
Starting in model year 2016, the RAM Promaster Chassis Cab and Cut Away are offered with a rear camera option. The package sales code is XA3. Included in this option package are an 11 meter video cable
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationRAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt
DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100852 1 Cable Installation
More informationField Installation Manual External Bolt-On Economizer for ComPac I Air Conditioners
Field Installation Manual External Bolt-On Economizer for ComPac I Air Conditioners Models: ComPac AVPA 42-48-60 The following instructions describe how to install the Marvair External Bolt-On Field Installed
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationPT230 PONTOON THRUSTER INSTALLATION MANUAL (PATENT PENDING) VOLUME 1.2, JUNE 2015
PT230 PONTOON THRUSTER (PATENT PENDING) INSTALLATION MANUAL VOLUME 1.2, JUNE 2015 Sideshift Inc. 130 Industrial Ave, Unit 303, Carleton Place, ON, Canada K7C 3T2 1.877.325.4787 +613.686.6011 INFO@SIDESHIFT.COM
More informationRAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100800 1 Cable Installation Kit 2000901-1 1 Dielectric Grease 2002872
More informationAM-516. Adaptor Ring. User s Manual. Complies with FD8162 fixed dome camera. Rev IP Surveillance
AM-516 Adaptor Ring User s Manual Complies with FD8162 fixed dome camera Rev. 1.0 IP Surveillance I Overview AM-516 Adaptor Ring Adaptor ring for FD8162 fixed dome camera. The supported installation types
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationBrighton 6' series Greenhouse
Brighton ' series Greenhouse ssembly instructions Model HSP Model HSP Walk-in Greenhouse Statement ear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following the detailed
More information