SIMPLE, ACCURATE AND INEXPENSIVE MEASUREMENT. MILLIMESS DIAL COMPARATORS.

Transcription

1 - Millimess. Digital and Dial Comparators SIMPLE, ACCURATE AND INEXPENSIVE MEASUREMENT. MILLIMESS DIAL COMPARATORS. Millimess is the classic amongst all measuring instruments, for over 60 years the Millimess series of dial comparators is synonymous for both high precision and extreme robustness. Maximum accuracy and a minimal reversal span error is obtained through the levers, gear and pinions being supported with jeweled bearings and that the measuring spindle running in a ball bush guide. Millimess is therefore particularly suitable for measuring tasks where the accuracy and the reversal span of a conventional dial indicator are not sufficient. Further advantages of Millimess are the simple handling, the easy reading as well as the movement being absolute shockproof. With a digital comparator with an inductive measuring system combined with most modern state of the art digital technology readings as small as 0.2 µm/ 10 µinch are realized. The practical control functions (for example tolerance monitoring or the storage of measuring values for dynamic measurements), a combined analog and digital display as well as the easy to use data transmission rounds off the complete Millimess spectrum.

2 + Millimess. Digital and Dial Comparators Millimess. Digital and Dial Comparators Inductive Digital Comparators (Short Range) Overview 6-2 Millimess With background lit digital and analog display Millimess 2000 / With digital and analog display µmaxµm 6-7 With digital display Maxµm III 6-10 With digital and analog display, probe Mechanical Dial Comparators Overview 6-14 Millimess 1002 /1003 / 1003 XL / 1004 / 1010 / Standard Versions Millimess 1000 A / 1000B / 1000 Z 6-18 With large dial Millimess Electrical Comparator with limit contacts Millimess 1103 N / 1104 N / 1110 N / 1150 N 6-20 Mechanical Dial Comparator with limit contacts

3 - 6-2 Millimess. Digital Comparators Millimess. Digital Comparators (Short Range) Overview Functions of Inductive Digital Comparators µmaxµm Maxµm III Catalog Page Measuring range 2.8 mm 1.8 mm 1.8 mm 2 mm 2 mm/ 3.98 mm Resolution mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/ mm/.0005 Functions: ON/OFF Zero setting the display Automatic Zero setting the analog display Switching between mm/inch Reversal of the counting direction Entering a numeral value Preset Data button Data via Control Instrument 2000sg ABS ABS/REL-switchable System 0 Tolerance display TOL Digimatic Dynamic Min, Max MAX MIN Meas. functions Max-Min (Tir) Resolution switchable Analog display Analog value switchable Lock function Optional Optional Data output Digimatic Opto RS232C RS232C Control output

4 + Millimess. Digital Comparators 6-3 Millimess. Digital Comparator With the new Inductive Digital Comparator Millimess 2100, everything is under control due to the visual tolerance monitoring which is indicated by the change of color in the background lit display Dynamic measuring MAX functions: MIN MAX / MIN for example, finding the reversal point MAX - MIN storing values for example when testing concentricity and flatness RS232C marconnect Digimatic The choice is yours: MarConnect Data output, choice between Digimatic and RS232C Control output can be connected to a SPS 0 TOL Tolerance function: clearly visual tolerance excess due to the change of color in the background lit display. ABS System Linearized, inductive absolute measuring system. Reference point is not lost when the instrument is switched off. 10 (µm) , ,400-2 Especially suited for use in a manufacturing environment. Waterproof protection class IP54 according to EN Code Initial First Numeral IP 5 International Protection Dust protected With linearity Without linearity High precision rotary stroke bearings for a longer service life and higher capacity Second Numeral 4 Protection against splash water in all directions

5 - 6-4 Millimess. Digital Comparators Inductive Digital Comparator Millimess 2100 with background lit display ABS System 0 TOL MAX MIN marconnect RS232C Digimatic Features Functions: ON/OFF RESET (zero setting the digital and analog displays) (set the analog display to zero) PRESET ( enter any numerical values) DATA (data transmission) mm/inch-switchable Reversal of counting direction RANGE (switch the meas. range and resolution) ABS (reference to elect. zero point) MAX / MIN memory, e.g. ideal to search for the reversal point MAX-MIN e.g. testing concentricity and flatness TOL (entering tolerance) LOCK: operating functions can be blocked via PC- Software Linearized inductive absolute measuring system Power supply via the main power adapter Data output: either Opto RS232C or Digimatic Dial Comparator can be remotely operated via the interface (Opto RS232C) Control output compatible to Dial Comparators with limit contacts Operating and display unit (bezel) can be rotated through 280 Measuring force spring is interchangeable Lower stop is adjustable Protection class IP54 according to EN Operating temperature 5-40 C High contrast background lit LCD with 6.5 mm high digits Analog display has a 4 mm long pointer which ensures better visual perception, ideal when checking concentricity and flatness as well as search for the reversal point when measuring bores Scope of supply: Mains adapter, rubber bellows and spanner for preliminary stroke setting Technical Data Measuring Resolution Display range Span of error* Over- Meas. Order no. Order no. ranges switchable of the G travel force switchable analog display within 230 V 115 V mm (inch) mm/inch mm (inch) ±0.8mm ±1.4mm mm N ±1.0 (.04 ) / ± (.0006 ) 0.001/ ± (.0015 ) ±1.4 (.055") 0.005/.0002" ± (.0060 ) 0.01/.0005 ± (.0150 ) * 1 Digit in any zero position ** Includes Adapter Bush 940 1µm 2µm **

6 + Millimess. Digital Comparators 6-5 Inductive Digital Comparators 2000 / 2001 ABS System RS232C marconnect Digimatic Features Extramess 2000 Functions: ON/OFF RESET (Zero setting the digital and analog displays) (Set the analog display to zero) PRESET ( enter any numerical values) mm/inch switchable Reversal of counting direction RANGE (Switch the meas. range and resolution) ABS (reference to elect. zero point) Battery charge status is indicated Linearized inductive absolute measuring system Power supply via the integrated rechargeable batteries (40 hrs.) or main power adapter Rate measuring values are actualized 20 values/s Data output: either Opto RS232C or Digimatic 2000 Dial Comparator can be remotely operated via the interface High contrast LCD with 6.5 mm high digits. Analog display has a 4 mm long pointer for better visual perception, ideal when checking concentricity and flatness as well as search for the reversal point when measuring bores Operating and display unit (bezel) can be rotated through 280 Measuring force spring is interchangeable Lower stop is adjustable Protection class IP54 Operating temperature 5-40 C Scope of supply: Mains adapter, rubber bellows and spanner for preliminary stroke setting Extramess MAX MIN 0 TOL Features are identical to Extramess 2000, in addition: MAX / MIN memory, e.g. ideal to search for the reversal point MAX-MIN e.g. testing concentricity and flatness TOL (entering tolerance) Block individual operating functions via Software (see accessories) Factor can be set/adjusted Control output compatible to Dial Comparators with limit contacts Scope of supply: Mains adapter, rubber bellows and spanner for preliminary stroke setting Technical Data Measuring Resolution Display Span of error* Over- Meas. Order no. Order no. ranges and range of G travel force switchable readings analog display 230 V 115 V mm (inch) mm/inch mm (inch) µm mm N (.07 ) 0.001/ ± (.0015 ) (.07 ) / ± (.0006 ) ** 0.8 (.031 ) / ± (.0003 ) (.07 ) 0.001/ ± (.0015 ) (.07 ) / ± (.0006 ) ** 0.8 (.031 ) / ± (.0003 ) * 1 Digit in any zero position ** Includes Adapter Bush 940

7 6-6-6 Millimess. Digital Comparators Inductive Digital Comparators 2100 / 2000 / ,5 1 Operating buttons 2 Display 3 Mounting shank 4 Measuring spindle 5 Contact point 901H 6 Connection or mains power supply 7 Data output 8 Rotatable operating and display unit (bezel) mm/inch RANGE ON/OFF I 30 mm ABS PRESET ABS 0 RESET SET Extramess ,5 ø63 16,5 8, b ø6,5 8,5 ø.375 ø65 75, ø8h6 ø4 42 (shown with 1085 b - not supplied) Control Instrument 2000sg Features Remote control buttons: RESET PRESET RANGE* DATA-button for data transmission, optionally via foot switch Power is supplied by the Extramess Connects to the Extramess with a built-in control cable Data can be transferred to a PC with an optional data cable Splash waterproof according to IP54 Order no * Function is limited when in conjunction with the 2100 Accessories Data Connection Cable Opto RS232C (2 m), SUB-D jack 9-pin Data Connection Cable Digimatic (2 m), flat plug 10-pin Software for 2001 for blocking/disabling individual operating functions, includes cable Cable to connect control output to an SPS Manual Lifter with cable release 2000 h Pneumatic Lifter 2000 p Measuring Force Adjuster 2000 m Mounting Lug Horizontal/Vertical 1085 b Adapter Bush for adapting mounting shank 8h6 mm to inch bore Measuring Force Springs 0.25 N N N N N N N h 5-8 bar ø 3 mm/inch RANGE ON/OFF 2000 p 2000 m Additional Accessories Page Contact Points Special Holder mm/inch RANGE ON/OFF mm/inch RANGE ON/OFF Accessories for Data Processing see Chapter 11

8 + Millimess. Digital Comparators 6-7 µmaxµm Digital Indicator The most valueable electronic indicator for high production measurements. Features ABS System 0 Inch/Metric operator selectable with switchable Inch resolution. Normal/Reverse Sensing Preset capabilities Optional Calibration Lockout feature. Absolute Transducer no overspeed errors or constant re-zeroing. Federal s unique transducer always remembers its location even when power is off. High resolution digital readout and analog bar graph digital display shows deviation from zero or a preset value. Lightweight, contamination resistant ruggedly built to with-stand hard use gasketed case, crystal and stem assemblies resist fluid contamination. Calibratable if ever needed values remembered even after battery change. Data output 2 popular formats 7-pin recessed connector Auto power down provides extremely low battery consumption, assuring long life from readily available commercial batteries. Unilateral Tolerances. Go/NoGo Display Feature. Increased resolution ( mm / 20 µinch) for today s demanding tolerances TOL Digimatic Technical Data Dimensions mm/inch A B C 11.7 / / / / / / 3.41 For Contact Points please refer to pages 5-27, 5-45 & mm 2.30in 40mm 1.58in 19mm.750in 6.3mm/.250in Display rotates 270 A B C

9 - 6-8 Millimess. Digital Comparators µmaxµm Digital Indicator Technical Data Range and Resolution Standard Units High Resolution Units Display Range Resolution Accuracy Resolution Accuracy % of Digital Range % of Digital Range Inch ± /.0001 ±.5% over ± ±. 5 % over ±.040 (switchable) ±.25 % over ±.020 ±..25 % over ±.020 Metric ± 1.0 mm mm ±.5% over ± 1.00 mm mm ±.5 % over ± 1.00 mm (1 µm) ±.25 % over ± 0.50 mm ±.25 % over ± 0.50 mm Specifications Spindle Range Repeatability to (-1.28 mm to mm) ± 1 digit Contact Point (Normally furnished PT-223) for.375 dia. stem,.250 long, radiused tip, 4-48 thread; (EPT-1037-W1) for 8 mm dia. stem, 6 mm long, radiused tip, M2.5 mm thread Gaging Force g/3-4 oz. (at center of spindle travel) Other gaging forces available call Technical Assistance Power 3 volt lithium coin cell (2 per unit, consumer type, CR 2450) Mahr Federal Model Number: EBY-1018 Battery Life nine months normal usage or 3000 hours Weight approx. 170 g/6 oz. Display Rotates through 270 Operating Temperature 50 to 130 F Perpendicular µmaxµm 58mm/ 2.30in "C" Stem diameter.375in or 8mm 16mm/ 0.625in C 34mm/ 1.339in A B Dimensions mm/inch A B 11.7 / / / / 2.25

10 + Millimess. Digital Comparators 6-9 µmaxµm Digital Indicator Ordering Information µmaxµm Indicators Model Number: EDI- X X X 0 X Style Range Resolution Code Ratio Code Stem dia./l** Code Back Code Standard ± 1 mm.001 mm 1 / ±.040 / 50 µinch High ± 1 mm.0005 mm 2 Resolution / ±.040 / 20 µinch Standard ± 1 mm.001 mm 3 Perpendicular / ±.040 / 50 µinch High ± 1 mm.0005 mm Resolution / ±.040 / 20 µinch 4 Perpendicular 1:1 0 4/5 1 Calibration 2* Lockout, 1:1 Calibration 3* Lockout, 4/5.375 / / mm / mm / Perpendicular 0 (no back) Lug 1 (EBK-1010) Flat 2 (EBK-1018) * Requires Calibration Access Key, EKY-1024 (sold seperately) ** Diameter / Length Note. Ask about our EDS-X models for special Setup Mode Lockout, MM/INCH Button Lockout, Calibration Lockout, Disable Sleep Mode and more Accessories Order no. Lug Back EBK-1010 Flat Back EBK-1018 Post Back EBK-1012 Screw Back EBK-1013 Back for Adjustable Mounting Brackets like AT-28 and AT-116 (slide sold separately) EBK-1014 Adjustable Back (.5 slot x 1/4-20 thread) EBK-1016 Mating Connector (7 pin) ECN-1720 Output Cable to Digimatic Serial output cable to DB-9 pin SCB-4 Dust Cover ECV-1307-W2 Calibration Access Key EKY-1024 Spring for lighter gaging force: 35 g / 1.2 oz. SP-351

11 Millimess. Digital Comparators Maxµm III Digital Indicator Next Generation A practical alternative to Dial Indicators and a universal replacement for Maxµm & Maxµm Plus ABS System Features Features both digital display for accuracy and readability and unique fan analog display for trend and change User configurable in inch / metric units, normal / reverse sensing, resolution, analog scale, and tolerance setup & display Dynamic Capabilities: Min, Max, TIR, Hold, Reset Absolute Transducers - no overspeed errors no missed counts no missed readings Auto power down - provides extremely low battery consumption, assuring long life from readily available commercial batteries Data output - 3 formats - Maxum, serial, or digimatic Both integral and remote readout versions available Easily used on Snap Gages, Bore Gages, Comparator Stands, and Fixture Gages Special options available: setup mode or calibration lockout, remote external power, 4:5 ratio, 12 o'clock mounted integral transducer, integral vertical or horizontal lug back, 1.5, 2.0 or 3.0 inch stem length, and more... IP54 protection Easy to select, order and operate! 0 TOL MAX MIN RS232C Digimatic Technical Data For short range indicators Standard Stem Length (± 1.0 mm/ ±.040 range indicators) A B C 17 mm/ mm/ mm/ 2.50 For long range indicators Standard Stem Length (± 1.99 mm/ ±.100 range indicators) 22 mm/ mm/ mm/ 2.87 For both short and long range indicators Long Stem Lengths 38 mm/ mm/ mm/ mm/ 2 * 70 mm/ mm/ mm/ 3 * 95 mm/ mm/ 4.83 Easily designed into your applications.. full-size Maxum Indicator and accessories, tracing templates or CAD files available on request. * Special Order Lengths

12 + Millimess. Digital Comparators 6-11 Maxµm III Digital Indicator Technical Data Description Short Range Long Range Digital Range Standard ±1.00 mm/ ±.040 ±1.99 mm/ ±.100 Reduced ±0.199 mm/ ±.0199 None Digital Resolution mm/ mm/.0005 Switchable mm/ mm/ mm/ mm/ Analog Range 5 or 25 or or 50 Analog Resolution 0.01 mm/ mm/.001 Switchable mm/ mm/ mm/.0001 Total Spindle Travel 3.04 mm/ mm/.250 Pre-Travel* 0.3 mm/ mm/.020 Over-Travel* 0.8 mm/ mm/.030 Accuracy Standard Range.5% of Total Range 0.35% of Total Range Reduced Range 0.25% of Total Range N/A Repeatability ±One Least Digit ±One Least Digit Gaging Force 3-4 oz / grams, preloaded Operation Temperature 10 to 55 C / 50 to 130 F Storage Temperature -20 to 65 C / -4 to 149 F IP Rating 54 Weight approx. 385 g / 13.6 oz. Battery Life approx hours Power 3.0 volt Lithium battery (type CR123A or equivalent) Mahr Federal Order Number: Contact Point (Normally furnished PT-223) for 0.375in dia. Stem, long, radiused tip, 4-48 thread; (EPT-1037-W1) for 8 mm dia. stem, 6 mm long, radiused tip, M2.5 thread. Stem Stem Data Order no. Order no. Length Diameter Output Short Range long Range 17 mm/ ** 38 mm/ No mm/ mm Output ** 38 mm/ mm * dependent on standard or reduced range selected. Standard range shown. ** Long Range Indicator Stem Length is / 22 mm 17 mm/ ** 38 mm/ Digital mm/ mm Output ** 38 mm/ mm 6 pin (D, E1) mm/ Digital Output ** 38 mm/ with mm/ mm Hold / Reset ** 38 mm/ mm 10 pin (E2)

13 Millimess. Digital Comparators Maxµm III Digital Indicator Technical Data Maxµm III Remote Indicating Unit* Order no. No Digital Output Port Digital Output -6 pin (D, E1) Digital Output with Hold & Reset -10 pin (E2) * Maxµm III Remote Indicating Units are NOT compaitible with traditional Remote Transducer models EAS-XXXX. Maxµm III Digital Transducer Digital Transducers Short Range Long Range Range ±1.00 mm/ ±.040 ±1.99 mm/ ±.100 Total Spindle Travel 3.04 mm/ mm/.250 Pre-Travel** 0.3 mm/ mm/.020 Over-Travel** 0.8 mm/.030 Gaging Force 3-4 oz/ grams, preloaded Operation Temperature 10 to 55 C/50 to 130 F Storage Temperature -20 to 65 C/-4 to 149 F Contact Point (Normally furnished PT-223) for dia. Stem, long, radiused tip, 2-48 thread; (EPT-1037-W1) for 8mm dia. Stem, 6mm long, radiused tip, M2.5 thread. ** dependent on standard or reduced range selected. Standard range shown. Transducer Stem Stem Order no. Order no. Type Length Diameter Short Range Long Range Canister 17 mm/ Canister 38 mm/ Canister 17 mm/ mm Canister 38 mm/ mm Pencil Body Diameter = Digital Transducer models X require an adaptor cable for use with traditional DEI-XXXXX Maxum and Maxum Plus Indicxating Units. Long Range Indicator Stem Length is / 22 mm. See Adaptor Cable selections as follows: Adaptor Cables For DEI with 6 pin split connector For DEI with 8 pin round connector Pencil Maxµm and Maxµm Plus Transducers are available as Replacement Parts. Refer to Part Price List for Part Numbers and Pricing. Maxµm III Remote Indicating units sold separately from Digital Transducer. Any Digital Transducer may be used with a MaxµmIII Remote Indicating unit. For English or Metric Contact Points visit pages 5-27 and 5-45 thru For alternate cable lengths or extension cables - call Mahr Federal's Technical Assistance Group. For special indicator options - call Mahr Federal's Technical Assistance Group. Canister

14 + Millimess. Digital Comparators 6-13 Maxµm III Digital Indicator Accessories For Integral Maxµm Indicators Lifting Levers 1) Furnished with washer and longer contact point. Left Right Angle Attachments Lever Type (not shown) (±.187 maximum range) Auxiliary Plunger Hole Attachments Short Lever (shown) (1.0 pivot to contact) Hand (shown) Order Model EAT-1034-W1 3 long,.500 O.D. Order Model EAT-1032-W1 Order no. EAS-1903 Spring Type (shown) Order no EAS-1912 Long Lever (not shown) Right Hand (not shown) (±.060 maximum range) (1.87 pivot to contact) Order no. EAS-1904 Order Model EAT-1035-W1 Order Model EAT-1033-W1 1) (For use on.670 stem length only, DEI-XX1X1) Ox-Bow Lifting Lever Order no. LR-40 * Other Accessories shown are for.375 stem models. Equivalent types are available for most Maxµm models having 8mm stems. Adaptor Bushing (BU-197) may also allow 8mm stem indicators to be used with the above accessories. Full size Maxµm Indicator and accessories tracing templates are available on request. Backs for Maxµm Indicators and Remote Indicating Units (Supplied with mounting screws) Lug Back (.250 hole) Mounts horizontally or vertically. Order no. EBK-1006 Adjustable Slide Back (.500 slot, 1/4-20 thread) Order no. EBK-1007 Rack Back Fits SE-33 (shown) and SE-73. Adjustable Mounting Block (not shown). Order no. EBK-1005 Replacement Screws 2-56 x.218 Order no. ESW-1252 Square Bracket (1/4-20 mounting thread) Order Model AAD-67 Rack Bracket (Shown mounted to SE-33 Adjustable Mounting Block.) SE-33 and SE-73 Adjustable Mounting Blocks are available separately. SE-33 is supplied with hex-screw adjust. SE-73 is supplied with knob adjust. Order Model EAD-1007-W1 (.375 I.D.) Order Model EAD-1007-W2 (8 mm I.D.) T Bracket Flange mounted. Order Model AAD-91 * Mounting Brackets shown are for.375 stem models. Equivalent types are available for most Maxµm models having 8 mm stems. Adaptor Bushing (BU-197) may also allow 8 mm stem indicators to be used with the above accessories. Full size Maxµm Indicator and accessories tracing templates are available on request. Other Maxµm Accesssories Data Output Cables for Maxµm III Serial Cable (6 pin to db9 pinf PC) Serial Cable (10 pin to db9 pinf PC) Digimatic Cable (6 pin to std 10 pin) Digimatic Cable (10 pin to std 10 pin) Send Data Footswitch used with Serial Cables above Mating Connectors MaxµmIII Models For 6 pin data output type (D, E1) ECN-1521 For 10 pin data output type (E2) ECN-1689 Remote Switch Assembly (for Hold/Reset) Handswitch EAS-2867 Footswitch EAS-2868 Splashcover for MaxµmIII ECV-1307-W1 Battery for MaxµmIII Overlay Kit for MaxµmIII Access Key (6 pin) Access Key (10 pin)

15 Millimess. Mechanical Dial Comparators Millimess. Mechanical Dial Comparators Overview Versions Measuring Readings Dial style Order no. Order no. range Splash waterproof Supramess 1002 ± 25 µm 0.5 µm Z ± Millimess 1003 ± 50 µm 1 µm Z ± Millimess 1003 XL ± 130 µm 2 µm Compramess 1004 ± 0.13 mm 5 µm Z ± Zentrimess 1010 ± 0.25 mm 0.01 mm Z ± Dezimess 1050 ± 1.5 mm 0.05 mm

16 + Millimess. Mechanical Dial Comparators 6-15 Millimess. Mechanical Dial Comparators Overview Design Features Constant Measuring Force Box type protective housing Lockable fine adjustment screw Measuring spindle can be retracted with either a screw in cable release or with a lifting knob Mounting shank and measuring spindle are both made of hardened stainless steel Self contained movement, which is both quick and easy to remove and replace Measuring spindle is mounted in a high precision ball guide (Types 1000/1002/ 1003/1004) for minimal hystersis Insensitive to lateral forces (side play) acting on the measuring spindle Easy to read scale Adjustable tolerance markers Maximum sensitivity and accuracy are ensured by the jeweled movement and in conjunction with the precision gears and pinions Shockproof Mechanism SHOCK PROOF Measuring spindle within the measuring range When the measuring range is exceeded the movement will be mechanically decoupled (shown in red)

17 Millimess. Mechanical Dial Comparators Mechanical Dial Comparators SHOCK PROOF XL 1003T*** Technical Data Measuring Readings Over- Meas. Accuracy* (DIN 879-1) Order no. Order no. range travel force G ges G e f u Standard** Splash water- Metric proof *** 1002 Supramess ± 25 µm 0.5 µm 2.8 mm 1 N 0.6 µm 0.5 µm 0.25 µm Millimess ± 50 µm 1 µm 2.8 mm 1 N 1.2 µm 1 µm 0.5 µm Millimess XL ± 130 µm 2 µm 2.5 mm 1 N 2.4 µm 2 µm 1 µm Compramess ± 0.13 mm 5 µm 2.5 mm 1 N 4 µm 3.5 µm 1 µm Zentimess ± 0.25 mm 0.01 mm 2.5 mm 1 N 8 µm 7 µm 2 µm Dezimess ± 1.5 mm 0.05 mm 0.3 mm 1 N 40 µm 35 µm 10 µm Inch 1002 Z Supramess ± N Z Millimess ± N Z Compramess ± N Z Zentimess ± N * Accuracy of 1004, 1010, 1010 Z, 1050 exceeds DIN ** Incl. Plastic Case; Adapter 940 (for inch instruments only) *** IP54, Incl. Plastic Case, Splash Guard Cover 957, Rubber Bellows (only for 1002/1003/1004); Adapter 940 (for inch instruments only)

18 + Millimess. Mechanical Dial Comparators 6-17 Mechanical Dial Comparators SHOCK PROOF ø8h6 ø M 2,5 ø8h6 ø M 2,5 1002/1003/ /1050 Accessories Order no. Adapter Bush for adapting mounting shank 8h6 mm to inch bore Cable Release to raise the measuring spindle Lifting Knob for lifting the measuring spindle Splash Guard Cover Rubber Bellows for 1002/1003/1004 to seal the open end of the measuring spindle Mounting Lug to mount on mounting shank 8h6 mm ø6, Additional Accessories Page Contact Points Special Holder Sensor Lever ø8h7 963

19 Millimess. Mechanical Dial Comparators Mechanical Dial Comparator Large Type Millimess 1000 A/B ,5 SHOCK PROOF A 951 ø16h6 ø28h ø ø6h7 18 R 3 Features Large design Easy to read dial Shockproof movement Jeweled movement bearings Measuring spindle is mounted in a high-precision ball guide which precludes play Scope of supply: Cable Release 951, case Accessories Order no. Contact Points with Steel ball with Ruby ball 921 R Cable Release to raise the measuring spindle Lifting Knob for lifting the measuring spindle Rubber Bellows to seal the open end of the measuring spindle Additional Accessories Page Precision Stand 824 GT 8-13 Technical Data Measuring Reading Scale Over- Measuring Accuracy Order no. Metric range division travel force G e G ges f u 1000 A ± 100µm 1 µm 1 mm 4 mm 3.5 N 1.5 µm 2 µm 1 µm B ± 50µm 1 µm 2 mm 4 mm 3.5 N 1.5 µm 2 µm 1 µm Inch 1000 Z ± N

20 + Millimess. Mechanical Dial Comparators 6-19 Electrical Comparator 1100 with limit contacts SHOCK PROOF ø22 Elmess Features Can be applied for example as tolerance control or as a precision contactor in automatic control systems Adjustable limit contacts; made from high-grade precious metal Limit contacts are particularly well protected against vibration and mechanical overload 118 ø8h6 18 ø Electrical Specifications Contact uncertainty with non-inductive load of 10 ma/24v +/- 0.3 µm max. contact rating max. contact voltage max. contact current 240 mw 24 V 100 ma Elmess 1100 Technical Data Measuring Overtravel Measuring Order no. range force 1100 ± 0.4 mm 2 mm 1.5 N

21 Millimess. Dial Comparators Mechanical Dial Comparators with limit contacts SHOCK PROOF 1103 N 1103 NT*** 1110 NT 1150 N Features Can be applied for example as tolerance control or as a precision contactor in automatic control systems A B Wiring diagram Design features are identical with Mechanical Dial Comparators, but with the addition of adjustable limit contacts; made from highgrade precious metal Limit contacts are particularly well protected against vibration and mechanical overload C Elzentimess A B 1 Undersize 2 God 3 Oversize C Technical Data Metric Measuring Readings Over- Meas. Accuracy* (DIN 879-3) Order no. Order no. range travel force G ges G e f u Standard** Splash proof*** 1103 N Elmillimess ± 50 µm 1 µm 2.8 mm 2 N 1.8 µm 1 µm 1 µm (T) N Elcompramess ± 0.13 mm 5 µm 2.5 mm 2 N 6 µm 3.5 µm 1.7 µm (T) N Elzentimess ± 0.25 mm 0.01 mm 2.3 mm 2 N 12 µm 6.5 µm 3.5 µm (T) N Eldezimess ± 1.5 mm 0.05 mm 0.3 mm 1.5 N 60 µm 35 µm 17 µm (T) Inch 1103 NZ Elmillimess ± N (T) NZ Elcompramess ± N (T) NZ Elzentimess ± N (T) * Accuracy of 1104 N, 1110 N and 1150 N exceeds DIN 879 ** Incl. Plastic Case, Setting Knob 953, Cable (1,2m); Adapter 940 (for inch instruments only) *** IP54, Incl. Plastic Case, Splash Guard Cover 957, Rubber Bellows (only for 1103/1110); Adapter 940 (for inch instruments only)

22 + Millimess. Dial Comparators 6-21 Mechanical Dial Comparators with limit contacts Electrical Specifications Contact uncertainty max. max. max. with non-inductive contact rating contact voltage contact current load of 10 ma/24v 1103 N +/- 0.3 µm 1104 N +/ µm 1110 N +/- 1.5 µm 1150 N +/- 7 µm 240 mw 24 V 100 ma Accessories Order no. Connection Cable (1.2 m), axial Connection Cable (5 m), axial Adapter Bush for adapting mounting shank 8h6 mm to inch bore Cable Release to raise the measuring spindle Setting Knob for setting the limit contacts without an additional setting standard Lifting Knob for lifting the measuring spindle Splash Guard Cover Rubber Bellows to seal the open end of the measuring spindle Mounting Lug to mount on mounting shank 8h6 mm Additional Accessories Page 1103/1104/1110/ ø8h6 ø4 63, M 2,5 Contact Points Special Holder Sensor Lever ø6, ø8h7 963