Dial Test Electronic Indicators Indicators (Lever Type}

Transcription

1 Dial Test Electronic Indicators Indicators (Lever Type} External Micrometers Dial Comparator Gage Brown & Sharpe s new dial comparator gages provide you with the accuracy needed to make comparative measurements, complete with an ø8 mm stem and a 3/8" bushing, allowing for a wide variety of setup options. Large, easy-to-read dial face with clear shadow-free scale. Constant measuring force: Only 1N. Self-contained, shockproof movement. Jeweled bearings and precision ground gears and pinions. Plus and minus tolerance markers. Screw-on safety cap prevents unintentionally changing the fine adjustment setting. Spindle retracting cable. White dial face. Meets DIN Spec DIN 879 Self-contained shockproof movement in in in E

2 Dial Test Indicators (Lever Type} BESTEST / TESATAST Dial Test Indicators All BESTEST and TESATAST indicators meet or exceed federal or DIN specifications. All BESTEST and TESATAST indicators are fur nished with a certificate of accuracy and traceability. BESTEST and TESATAST in di ca tors provide all of the following features: Constant Clockwise Rotation Indicator pointer always rotates clockwise (whether measuring over or under) to elim i nate plus or minus confu sion. Automatic Reversal Measuring is bi-directional with double lever system. No switch to interfere with move ment. Measures inside, outside, over and under. Swiveling Point Contact point can be set over 210 arc to measure hard-to-reach areas. Universal Mounting Dovetails top, front and back for required mount ing ori en ta tion and rigid set up. Carbide Tip Furnished as standard on all BESTEST/TESATAST indicators. Monobloc (precision watch) Body Design All pinions are mounted in jeweled bearings in an isolated assembly com pletely separate from outer body to maintain highest ac cu ra cies. Anti-Magnetic and Corrosion Resistant Safe for use around mag net ic chucks. Chrome plated to resist corrosion. BESTEST -3 and -13 Series BESTEST -3 and -13 sets are furnished with.080" carbide contact points, a rectangular bar, swivel clamp, point wrench and a certificate of accuracy and traceability. The -3 sets with end mount ed dials are fur nished with a universal dovetail mounting attachment (7054) in place of the rect an gu lar bar and swivel clamp E-33

3 Dial Test Electronic Indicators Indicators (Lever Type} External Micrometers BESTEST/TESATAST -5 Series (Black Face) BESTEST -5 sets are furnished with a.080" carbide contact point, a.250" diameter extension with dovetail, point wrench and a cer tif i cate of accuracy and traceability in a durable molded case. DIN 2270 NF E Rotating dial BESTEST -6 Series (White Face) BESTEST -6 sets are furnished with 3 carbide contact points,.040",.080", and.120", 2 extensions with dovetail, point wrench and a certificate of accuracy and traceability in a durable molded case. TESATAST Every TESATAST is furnished with a.080" (2 mm) carbide contact point, a.310" (8 mm) di am e ter extension with dove tail, a point wrench and a cer tif i cate of ac cu ra cy and trace abil i ty in a durable molded case. E-34

4 Dial Test Indicators (Lever Type} Top Mounted Models End Mounted Models Side Mounted Models Well-proven lever-type dial test indicators with dial face mounted parallel dial face mounted at right angle to with dial face mounted parallel Lever-type dial test indicators with Lever-type dial test indicators to the insert s axis. the insert s axis. to the insert s axis, but on the flat side of the dial housing BESTEST/TESATAST Dial Test Indicators (Lever-Type) These lever-type dial test indicators are especially intended for use on the shop floor or in the inspection room Ideally suited for comparative measurements on a surface plate, for instance Determine form, shape and positional deviations, as well as axial and runout errors. Bi-directional measuring with automatic reversal inside the movement. Continuous clockwise pointer rotation providing error-free reading. Insensitive to magnetic fields. Jeweled movement with 7 rubies. Ball-bearing lever system with measuring insert swiveling through to 240. Very low measuring force. Full-metal construction giving exceptional durability. Monobloc housing with 3 countersunk dovetail attachments. 17,4 10, / 94 ø 38,4 ø 28, / / ,8 35,8 ø 2 8,3 7,6 11,8 35,8 11,8 35, Technical Data ø "/.0005"/.00005"/ 0.02 mm 0.01 mm mm.001"/.0004"/.0001"/ Deviation span 27 μm 10 μm 2 μm Deviation span within.0005"/ the local measuring span 0.20 mm 12 μm.0002"/ 0.10 mm 5 μm.00005"/ 0.02 mm 1 μm Total deviation span.0012"/ 31 μm 13 μm 3.5 μm.00016"/.00012"/.00005"/ Repeatability limit 4 μm 3 μm 1 μm.00016"/.00012"/.00006"/ Max. hysteresis 4 μm 3 μm 1.5 μm Measuring force with the following measuring inserts mm long 0.15 N 0.15 N mm long 0.06 N 0.06 N E-35

5 Dial Test Electronic Indicators Indicators (Lever Type} External Micrometers Accessories TESA IP65 Electronic Dial Test Indicators (Lever-Type) All the mechanical advantages of a dial test indicator, with a digital reading and a durable IP65 compliant design. Patented inductive measuring system Analog and numerical indication Numerical interval.0005/ in / 0.01/0.001 mm Selectable scale division: 10, 20, 50 µm/1, 2, 5 µm IP65 compliant Water and coolant resistant Inch/metric conversion RS-232 data output combined with external power supply Displayed measuring modes (NOR/MIN/MAX/MAX-MIN) Automatic shut down Compatible with all TESATAST accessories ø 1.5 (Diagram dimensions shown in mm) in mm mm Insert N (± 15%) / / / / ø 44 LCD, 5 digits + sign Digit height:.24 in / 6 mm Zero-setting Max. perm. error: 10 μm Repeatability: 1 μm Hysteresis: 3 μm max m/s max m/s Number of measurements: 9/s Operating temperature range: 41 F to 104 F +5 C to + 40 C Lithium battery, 3V, type CR 2032 Autonomie > 4000 hours RS oz oz EN Degree of protection IEC 529: IP65 Supplied in a plastic case with: 1 insert with a.0787 in / 2 mm dia. No wrench No in / 8 mm dia. mounting rod No Identification number Declaration of conformity E V lithium battery, 190 mah, type CR RS-232 connection cable with external power supply Compatible with TESATAST measuring inserts and accessories, page E-47

6 Dial Test Indicators (Lever Type} DIN 2270 NF E Top Mounted Dials BESTEST indicators with top mounted dials are supplied with a rectangular bar, swivel clamp, contact point wrench and a certificate of ac cu ra cy and traceability in a fitted case. Contact points for models on this page are 1/2" (12.5 mm) long. Carbide tips are.080" (2 mm) diameter. Available with either 1" (28 mm) or 1-1/2" (38 mm) diameter dials. TESATAST indicators are supplied in a plastic case with.080" (2 mm) ball-end carbide contact point, 1 key for fixing the point, 1 extension w/dovetail.31" (8 mm) diameter, an instruction leaflet and a test certificate. Rotating dial Inch Reading (±.0001" Repeatability, ±.0005" Calibration Accuracy) in.030 in 1 in in.030 in 1 in in.030 in 1-1/2 in Inch Reading (±.00002" Repeatability, ±.0001" Calibration Accuracy) in.008 in 1 in in.008 in 1-1/2 in in.008 in 1-1/2 in Metric Reading (±0.002 mm Repeatability, ±0.01 mm Calibration Accuracy) mm 0.8 mm 28 mm mm 0.8 mm 38 mm Metric Reading (± mm Repeatability, ±0.002 mm Calibration Accuracy) mm 0.2 mm 28 mm mm 0.2 mm 38 mm Dial Dia. E-37

7 Dial Test Electronic Indicators Indicators (Lever Type} External Micrometers End Mounted Dials All BESTEST indicators with end mounted dials come with con tact points 1/2" long with a carbide tip.080" diameter, a No universal dovetail mounting attachment, a contact point wrench and a certificate of accu racy and traceability in a fitted case. DIN 2270 NF E Rotating dial Inch Reading in.030 in 1 in ±.0001 in.0005 in in.008 in 1-1/2 in ± in.0001 in in.008 in 1-1/2 in ± in.0001 in Metric Reading mm 0.8 mm 28 mm ±0.002 mm ±0.01 mm mm 0.2 mm 38 mm ± mm ±0.002 mm All TESATAST indicators are supplied in a plastic case with.08 in (2 mm) ball-end carbide contact point, 1 key for fixing the point, 1 extension w/dovetail.31 in (8 mm) diameter, an instruction leaflet and a test certificate. Dial Dia. Side Mounted Dials BESTEST indicators with side mounted dials. Contact points are 1/2" long. Car bide tip is.080" diameter. Ideal for height gages, transfer gages and Digit-Hite plus. Supplied with a rect an gu lar bar, swivel clamp, contact point wrench, and a certificate of accuracy and trace abil i ty in a fitted case. E-38 Inch Reading in.030 in 1-1/2 in ±.0001 in ±.0005 in in.030 in 1 in ±.0001 in ±.0005 in in.008 in 1-1/2 in ± in ±.0001 in in.008 in 1 in ± in ±.0001 in Metric Reading Dial Dia mm 0.8 mm 28 mm ±0.002 mm ±0.01 mm mm 0.2 mm 28 mm ± mm ±0.002 mm

8 Dial Test Indicators (Lever Type} Easy Reading Console Faces DIN 2270 NF E BESTEST -5 Series (Black Face) Easy-to-read, satin-black, jet console face, BESTEST in di ca tors with high visibility orange hand. BESTEST -5 sets are fur nished with a.080" carbide contact point, a.250" diameter extension with dovetail, point wrench and a certificate of accuracy and trace abil i ty in a durable molded case. Rotating dial in / / / / / / / / / /16 in Dial Dia. (in) Inserts (in) E-39

9 Dial Test Electronic Indicators Indicators (Lever Type} External Micrometers BESTEST -6 and -14 Series (White Face) BESTEST -6 and -14 sets are fur nished with 3 car bide contact points,.040",.080" and.120", one 1/2" long x.25" di am e ter extension with dove tail, one 1/2" long x.22" di am e ter ex ten sion with dovetail, a contact point wrench and a cer tif i cate of accuracy and trace abil i ty in a durable molded case. DIN 2270 NF E Rotating dial E-40 Inch Reading (±.0001" Repeatability, ±.0005" Calibration Accuracy) in.030 in 1 in in.030 in 1-1/2 in Inch Reading (±.00002" Repeatability, ±.0001" Calibration Accuracy) Dial Dia in.008 in 1 in in.008 in 1-1/2 in Metric Reading (±0.001 mm Repeatability, ±0.01 mm Cali bra tion Accuracy) mm 0.8 mm 28 mm mm 0.8 mm 38 mm Metric Reading (± mm Repeatability, ±0.002 mm Calibration Accuracy) mm 0.2 mm 28 mm

10 External Micrometers Dial Test Indicators (Lever Type} Extra Long Contact Points BESTEST indicators with top mounted dials. Contact points are 1-7/16" long. Carbide tip is.080" di am e ter. Supplied with a rectangular bar, swivel clamp, contact point wrench and a certificate of accuracy and traceability in a fitted case. All TESATAST indicators are supplied in a plastic case with.080" (2 mm) ball-end carbide contact point,1 key for fixing the point, a.31" (8 mm) diameter extension with dovetail, an instruction leaflet and a test certificate. DIN 2270 NF E Rotating dial Top Mounted Inch Reading (±.0001" Repeatability, ±.0005" Calibration Accuracy) in.020 in 1 in in.020 in 1-1/2 in Vertical/End Inch Reading (±.0001" Repeatability, ±.0005" Calibration Accuracy) in.020 in 1 in Side Mount Inch Reading (±.0001" Repeatability, ±.0005" Calibration Accuracy) in.020 in 1-1/2 in Top Mounted Metric Reading (±0.002 mm Repeatability, ±0.01 mm Calibration Accuracy) mm 0.5 mm 28 mm mm 0.5 mm 38 mm Vertical/End Metric Reading (±0.002 mm Repeatability, ±0.01 mm Calibration Accuracy) mm 0.5 mm 28 mm Side Mount Metric Reading (±0.002 mm Repeatability, ±0.01 mm Calibration Accuracy) - - Dial Dia mm 0.2 mm 38 mm E-41

11 Dial Test Indicators Electronic BESTEST Indicators Accessories External Micrometers BESTEST Universal Test Indicators Full jewelled movement in a universal indicator A. Inch Indicator Set complete with case B. Metric Indicator Set complete with case Components for Indicator Set ( Inch and Metric) C. Swivel for Posts.312 diameter and mounting rods.220 to.250 diameter D. Clamp: 1-5/16" range and 1/4-28 threaded hole E. Hole Attachment w/ Indicator Mounting Hole.375" dia. and finger 7/32" dia. w/ 1-7/8" reach F. Bar: 5-5/16" long x 3/8" thick x 3/4" high w/ tapped thru holes at top, bottom and both sides of front and one tapped hole at back end for attaching Holding Rods G. Holding Rod:.312" x 5" long H. Holding Rod:.312" x 3" long I. Fitted Case for indicator and accessories E-42

12 Dial Test Indicators BESTEST Accessories Dial Test Indicators - BESTEST Accessories A E F B G H C I D J Components for Accessory Set A. Rectangular bar 3/16" thick x 5/16" high x 3" long with.220" diameter stud B. Round bar 7/32" diameter with.163" stepped end;.220" diameter stud; 2-7/8" long C. Swivel support (short) 3/8" diameter x 1" long shank D. Angle attachment 3/8" hole with 3/8" diameter x 1" long shank E. Extension with dovetail.220" diameter x 1/2" long shank F. Extension with dovetail.250" diameter x 1/2" long shank G. Carbide ball contact point.040" diameter x 1/2" long H. Carbide ball contact point.120" diameter x 1/2" long Complete set of accessories (A-H above) Additional Accessories I. Rectangular bar: Furnished with all front-mounted BESTEST indicators. 1/4" thick x 1/2" high x 3" long with.220" diameter stud J. Swivel support (long): 3/8" diameter x 3-5/8" long shank E-43

13 Dial Test Indicators Electronic BESTEST Indicators Accessories External Micrometers Universal Clamp For mounting in di ca tor on dovetail. 7/32" hole in swivel. Dovetail end has 7/32" hole and 5/32" hole adjacent to the dovetail. For use on Interapid 312 style indicators Universal Swivel Clamp Dovetail opposite 3/8" mounting hole and V-side hole with clamp screw for range 1/8" to 1/4" Swivel Clamp 3/8" and 7/32" dia. mounting holes. Dove tail opposite 3/8" hole. For use with all front-mounted dial BESTEST/TESATAST in di ca tors E-44

14 Dial Test Indicators BESTEST Accessories Universal Dovetail At tach ment Supplied with vertical top-mounted dial BESTEST in di ca tors. Fits all BESTEST indi cators and dovetail-mounting elec tron ic gage heads. Chrome plated. Shank is 1/4" diameter x 2-1/2" long (to center of ball) Lug-Back Bracket Dovetail fits all BESTEST in di ca tors and dovetail-mount ing electronic heads. Mounting slot is 1/4" Combination BESTEST Indicator Axial Support Used for mounting indicator on dovetail or rod. Hinges on support allow indicator to be positioned for best orientation to work piece. Support mounting stem is 3/8". Tool length is 5-1/4" E-45

15 Dial Test Indicators Electronic BESTEST Indicators Accessories External Micrometers Contact Points Contact points of different lengths are not in ter change able because any change in length of point radically changes the mag ni fi ca tion of the indicator. Be sure to replace or interchange only with points of the same length. Points of the same length but having different tip di am e ters are com plete ly interchangeable Ruby Tip Contact Points R R R R R E-46 Length x Tip Dia. (in / mm) Ball Material For use with BESTEST indicators , 7022, 7023, 7024, 7029, 7030, 7031, 7032, 7033, 7037, and 7038 inch and metric models: /2 x.015 / 12.5 x 0.4 Carbide /2 x.040 / 12.5 x 1 Carbide /2 x.040 / 12.5 x 1 Steel /2 x.080 / 12.5 x 2 Carbide /2 x.080 / 12.5 x 2 Steel /2 x.120 / 12.5 x 3 Carbide /2 x.120 / 12.5 x 3 Steel For use with and BESTEST indicators: /16 x.040 / 37 x 1 Carbide /16 x.080 / 37 x 2 Carbide /16 x.080 / 37 x 2 Steel /16 x.120 / 37 x 3 Carbide Ruby Tip Contact Points R /2 x.040 / 12.5 x 1 Synthetic Sapphire R /2 x.080 / 12.5 x 2 Synthetic Sapphire R /2 x.120 / 12.5 x 3 Synthetic Sapphire R /16 x.080 / 37 x 2 Synthetic Sapphire R /16 x.120 / 37 x 3 Synthetic Sapphire Contact point thread size is M1.4 x 0.3

16 Dial Test Indicators BESTEST Accessories Dial Test Indicators - TESATAST Accessories Styli are available with various ball tip diameters and lengths in either hard-chrome plated or carbide ball tips Hard-chrome Carbide Ball Tip in/mm / 1.5 / / 2.5 / / 3.5 / / / / / / / 36.5 Note: Same point for both inch and metric instruments in/mm E-47

17 Dial Test Electronic Indicators Indicators (Lever Type) External Micrometers TESATAST Accessories in mm Fixing shanks and supports for clamping the TESATAST in the measuring position. Dovetail shanks: /32 in (8 mm) x.5 in (12 mm) /4 in (8 mm) x.5 in (12 mm) Rod shank: /8 in (8 mm) dia. x 3.5 in (80 mm) Oblong section shank: /2 in x 1/4 in x 3 in (13 x 6 x 75 mm) Swivel shanks: /8 in (8 mm) dia. x 1 in (25 mm) /8 in (8 mm) dia. x 3.5 in (90 mm) Angle shanks: /8 in (8 mm) dia. x 1 in (25 mm) Centering support with shank 3/8 in (8 mm) dia. x 1 in (25 mm) clamping by dovetail and 3/16 in (4 mm) bore Fixing clamp, double E-48 Sets and additional accessories: Set of accessories consisting of: stylii, stylii, stylii, key holder, dovetail shank or dovetail shank, dovetail shank or dovetail shank, case Set of accessories consisting of: clamp, shank or shank, support or support, shank or shank, shank or shank, shank or shank, case Set similar to or but with centering support in addition, in case Stylus key

18 Dial Test Indicators (Lever Type) INTERAPID 312 Dial Test Indicators (Lever-Type) Very large measuring span Ideal for inspecting all significant size variations, e.g. on the surface plate Measure positional, form and shape errors. For measurement at 12. With revolution counter. Inclined, easy-to-read dial. One piece, solid case. High rigidity. Very high sensitivity, very light measuring pressure. Jeweled mechanism fitted with ball-bearings. Fully reversible, swiveling through 210 without reversing lever. Hard steel or tungsten carbide contact points. Variety of mounting positions. Horizontal Model Time-tested dial test indicator (lever-type) with dial face mounted parallel to the insert axis. Vertical Model Dial test indicator (levertype) with dial face mounted at right angle to the insert axis. A Angular position of 12 for stylus insert The models INTERAPID 312 are designed to give a true reading when the angle between the stylus and the workpiece surface is 12 (Fig. A). In other measuring positions, including the parallel position of the stylus against the workpiece surface, the values read have to be corrected (Fig. B). Measuring direction Technical Data 0.01 mm mm Pointer Revolution 1 2 Pointer Revolution 1 2 B Measuring direction Deviation range 10 μm 20 μm 4 μm 8 μm Total deviation range 13 μm 23 μm 6 μm 10 μm Repeatability limit 3 μm 1 μm Measuring direction Max. hysteresis 3 μm 2 μm Measuring force 0.12 N 0.25 N E-49

19 Dial Test Electronic Indicators Indicators (Lever Type) External Micrometers INTERAPID 312 Horizontal Models Series Bezel Dia. Inserts in b b b b b b mm Rotating dial Very low measuring force as in the table on page E-45 Lever system with friction drive preventing from overload Accuracy: see table on page E mm mm mm mm Supplied in a plastic case with: 1 insert with a.080 in / 2 mm dia. in hardened steel 1 key No Identification number Declaration of conformity INTERAPID 312 Vertical Models Bezel Dia. Inserts in mm E-50

20 Dial Test Indicators (Lever Type) Full Indicator Sets with Accessories Full sets consist of: Technical data as listed under each single product Plastic case Identification number INTERAPID 312 dial test indicators as shown in the tables hereafter Height gage bar with clamp Reducing sleeve, inch or Adapter sleeve 5/ 32" - 3/ 8" Axial support -.375" stem or Axial support - 8 mm stem Case for contact points Contact point wrench Declaration of conformity INTERAPID 312 Horizontal Models in mm INTERAPID 312 Vertical Models in mm E-51

21 Dial Test Electronic Indicators Indicators (Lever Type) External Micrometers Measuring Inserts for INTERAPID 312 Series 312 Dial Test Indicator Sets Length L of the measuring inserts L Note: The original measuring insert mounted on every INTERAPID 312 and other inserts with same nominal length but having different tip diameters are completely interchangeable. Ball tips in hardened steel or tungsten carbide M1.7 coupling thread Steel Ball Tips Carbide Ball Tips L in all** all** all** all** * all** * *** **** mm * * * * in / mm Key for measuring inserts Case for measuring inserts * The length of the used insert changes the amplification factor of the lever system, therefore, each read value must be doubled. ** Except for models No and No *** Only for model No **** Only for model No E-52

22 Dial Test Indicators (Lever Type) Accessories for INTERAPID = in mm in mm Height gage bar with clamp Height gage bar /2 x 1 /4 x 2 13 x 6 x 50 ø 7 /32 ø Double attachment with clamping ø 4 point and dovetail Swivel holder ø 3 /8 x 5.25 ø 8 x 133 with clamping points ø 4 and dovetail Reducing sleeve ø 3 /8 / ø 5 /32 ø 8 / ø Rectangular fixing shank 3 /16 x 5 /16 Contact Points For INTERAPID Models 310-3, 311-3, 310-b-3, 311-bn-3, 312-3, Type Carbide.080 in.812 in Carbide.060 in.812 in Carbide.031 in.812 in Chrome.080 in.812 in Chrome.060 in.812 in Chrome.031 in.812 in * Carbide.080 in in * Carbide.031 in in Chrome 2.0 mm 15.2 mm Carbide 2.0 mm 15.2 mm Carbide 1.5 mm 15.2 mm Chrome 0.8 mm 15.2 mm * Carbide 2.0 mm 34 mm Carbide 0.8 mm 15.2 mm * Carbide 0.8 mm 34 mm With.0001 in (0.002 mm) graduations * Note when these special purpose contact points are used, the dial reading must be doubled to obtain the correct reading! E-53

23 Lever Dial Test Indicators A B Measuring direction Measuring direction α Shorten lever COMPAC Lever Dial Test Indicators Essential for the workshop, but also in the inspection room and laboratory Ideal for comparative measurement on a surface plate Detect form and position errors Measure axial and radial runouts, especially. Technical features: Long range up to 3 mm. Bi-directional measuring, without reversing lever. Continuous clockwise rotation of the pointer in both ways. Swivelling probe through 180. Main pivot on oversized, self-aligning angular bearings. Dovetail mounting directly machined in the indicator body. Dull-chrome plated bezel and housing. Rotating dial. Insensitive to magnetic fields produced in universal precision mechanics. Note for use of the COMPAC dial test indicators (lever-type): When the measuring insert is parallel to the workpiece surface (Fig. A), these dial test indicators give true reading as the amplification factor is 1:1. In other measuring positions (angle α in Fig. B), the effective lever length changes so that the read value need be corrected. With respect to this, also refer to the instruction manual. Series 210, standard DIN 2270 and factory standard Rotating dial Friction lever system for preventing from overload Contact points with tungsten carbide ball tips Delivery in a suited plastic case including: 1 x 2 mm dia. contact point 1 x 8 mm dia. rigid stem, L = 15 mm (No ) 1 x 4 mm dia. rigid stem, L = 15 mm (No ) Serial number Inspection report with a declaration of conformity ø 0.79 Inch reading Order Reading Total Travel per Bezel Contact Total Repeat- Hysteresis N Code Range Revolution Point Reading ability in in in in L in error (in) in in 212A A GA LA GLA A GA Metric reading E-54 Order Reading Total Travel per Bezel Contact Total Repeat- Hysteresis N code Range Revolution Point Reading ability mm mm mm mm L mm error (μm) μm μm G L GL G GL G

24 Lever Dial Test Indicators Series 220, perpendicular Inch reading Order Reading Total Travel per Bezel Contact Total Repeat- Hysteresis N Code Range Revolution Point Reading ability in in in in L in error (in) in in 224A GA LA GLA A GA Metric reading Order Reading Total Travel per Bezel Contact Total Repeat- Hysteresis N Code Range Revolution Point Reading ability mm mm mm mm L mm error (μm) μm μm G L GL G E-55

25 Lever Dial Test Indicators Series 230, parallel DIN 2270 and factory standard Rotating dial Friction lever system for preventing from overload Contact points with tungsten carbide ball tips Delivery in a suited plastic case including: 1 x 2 mm dia. contact point 1 x 8 mm dia. rigid stem, L = 15 mm (No ) 1 x 4 mm dia. rigid stem, L = 15 mm (No ) Serial number Inspection report with a declaration of conformity Inch reading Order Reading Total Travel per Bezel Contact Total Repeat- Hysteresis N Code Range Revolution Point Reading ability in in in in L in error (in) in in 234A GA LA GLA A GA Metric reading Order Reading Total Travel per Bezel Contact Total Repeat- Hysteresis N Code Range Revolution Point Reading ability mm mm mm mm L mm error (μm) μm μm G L GL G E-56

26 Lever Dial Test Indicators DIN 2270 and factory standard Series 240, with reduced range One-Revolution Rotating dial Friction lever system for preventing from overload Contact points with tungsten carbide ball tips Delivery in a suited plastic case including: 1 x 2 mm dia. contact point 1 x 8 mm dia. rigid stem, L = 15 mm (No ) 1 x 4 mm dia. rigid stem, L = 15 mm (No ) Ø ø27 ø40 L Serial number Inspection report with a declaration of conformity Inch reading Order Reading Total Bezel Contact Total Repeat- Hysteresis N Code Range Point Reading ability in in in L in error (in) in in 244A GA LA GLA A GA Metric reading Order Reading Total Bezel Contact Total Repeat- Hysteresis N Code Range Point Reading ability mm mm mm L mm error (μm) μm μm G L GL G E-57

27 Lever Dial Test Indicators Contact Points for Lever Dial Test Indicators Tungsten carbide or ruby ball tips Inch reading M1,6 coupling thread Standard contact points mounted on all dial test indicators can easily be replaced by those having a same length, but with a different diameter. Carbide Ball Tips COMPAC TESA mm L in 4/240A A /240A A /240A A /210A A /210A A /210A A /210LA LA /210LA LA /210LA LA /240LA LA /240LA LA /240LA LA Metric reading Carbide Ball Tips Ruby Ball Tips Compac TESA Compac New mm L mm 4/ / /210-82R R / /210L L /210L L /210L-82R 210L082R /210L L /240L L /240L L /240L-82R 240L082R /240L L Contact points with COMPAC order codes are available while stock lasts. Contact points with TESA order number are in stainless steel. E-58

28 Lever Dial Test Indicators 1 Accessories for Lever Dial Test Indicators Fixing shank with dovetail clamp / Fixing shank with dovetail clamp / Cylindrical fixing shank 8 x / 8 x 3.5 with clamp / Rectangular fixing shank 13 x 6 x / 2 x 1 / 4 x 2 with clamp / Short swivel holder with cylindrical shank 8 x / 8 x 1 and dovetail clamp Long swivel holder with cylindrical shank 8 x / 8 x 3.5 and dovetail clamp Angle holder with cylindrical shank 8 x / 8 x 1 Clamping bore 8 3 / Holder shoulder for perpendicular model with cylindrical shank 8 x / 4 x 1 Clamping point for fixing shank 4 and dovetail clamp Double fixing clamp with dovetail clamp Long swivel holder with cylindrical shank and 8 x 125 dovetail clamp as well as fine adjustment Fixing shank with dovetail clamp 6 13 mm 15 in 30 ø D Dovetail fixing shanks and mounting lug Fixing shank swivelling through ± 30 1 / 4 in Rigid fixing shank 1 / 4 in Fixing shank swivelling through ± 30 8 mm Rigid fixing shank 8 mm Fixing shank swivelling through ± 30 4 mm Rigid fixing shank 4 mm TA6 Fixed stem 5 / 16 in TMA6 Swivel stem through ± 30 5 / 16 in TA8 Fixed stem 3 / 8 in TMA8 Swivel stem through ± 30 3 / 8 in D ø 16 26,8 ø D ø ,8 Stem Clamping length SPT Rotating holder 8 mm 25 mm SPTA Rotating holder 1 / 4 in 1 in SPTA-3/16 Rotating holder 3 / 16 in 1 in SPTA-3/8 Rotating holder 3 / 8 in 1 in SPTA-5/16 Rotating holder 5 / 16 in 1 in E-59

29 Dial Gages 40 mm Diameter Dial Gages, Perpendicular DIN 878 and factory standard Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Adjustable tolerance markers. M2,5 coupling thread for contact points. Fastening sleeve with a 8h6 or 25h6 diameter Contact points with a 3 mm dia. ball tip, already mounted Cardboard box Serial number Inspection report with a declaration of conformity Total Repeat- Hyste- N Reading ability resis mm mm mm mm error (μm) μm μm CP CP 352S 0.01 ± (1) CP CP CP 355S ± (0.2) S: Models with a reduced range. Since the pointer travels less than one revolution, all reading errors due to the revolution counter are eliminated. E-60

30 Dial Gages JET Type Dial Gages DIN 878, NF E Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Ajustable tolerance markers. M2,5 coupling thread for contact point Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Serial number Inspection report with a declaration of conformity ø ø ø8h6 ø4 6 ø37 ø40 50 (77.4) 43 ø8h6 68 ø3 ø5 ø4.5 6 (111) ø58 ø53 Inch models ø5 ø3 Total Repeat- Hyste- N Reading ability resis in mm in in in error (in) in in 314AK AK Metric models Total Repeat- Hyste- N Reading ability resis mm mm mm mm mm error(μm) μm μm 313K , K E-61

31 Dial Gages 40 mm Diameter Dial Gages Series 350, reading to 0.01/0.002 mm DIN 878, NF E , factory standard Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers. M2,5 coupling thread for contact point Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Metric models Total Repeat- Hyste- N Reading ability resis mm mm mm mm error(μm) μm μm B E S 0.01 ± (0.5) SB 0.01 ± (0.5) SE 0.01 ± (0.5) B E Inch models Serial number Inspection report with a declaration of conformity E-62 Total Repeat- Hyste- N Reading ability resis in in in in error (in) in in 352A AB AE A AB AE AS.0005 ± (.020) ASB.0005 ± (.020) ASE.0005 ± (.020) A AB AE B: With bezel lock. E: Watertight as per DIN 40050, IP64. S: Models with a reduced range, balanced reading. Since the pointer travels less than one revolution, all reading errors due to the revolution counter are eliminated.

32 Lever Dial Dial Test Gages Indicators DIN 878, NF E , factory standard Rotating dial 40 mm Diameter Dial Gages Series 360, reading to 0.002/0.001 mm Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers. M2,5 coupling thread for contact point Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Serial number Inspection report with a declaration of conformity Metric models Total Repeat- Hyste- N Reading ability resis mm mm mm mm error(μm) μm μm 365S ± (0.2) SB ± (0.2) SE ± (0.2) B E S ± (0.1) SB ± (0.1) SE ± (0.1) B: With bezel lock. E: Watertight as per DIN 40050, IP64. S: Models with a reduced range, balanced reading. Since the pointer travels less than one revolution, all reading errors due to the revolution counter are eliminated. Inch models Total Repeat- Hyste- N Reading ability resis in in in in error (in) in in 367A AB AE AS ± (.005) ASB ± (.005) ASE ± (.005) E-63

33 Dial Gages 58/82 mm Diameter Dial Gages Series 531, reading to 0.1 mm DIN 878, NF E , factory standard Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers (models with a 58 mm dial diameter only). M2,5 coupling thread for contact point. Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Serial number 19, ø10 Inspection report with a declaration of conformity ø82 ø58 ø53 (111) 43 ø8 h6 50 / / 72 6 ø4.5 ø5 ø3 M 2,5-6H Metric models Total Repeat- Hyste- N Reading ability resis mm mm mm mm mm error(μm) μm μm B G GB B: With bezel lock. G: Large dial having a 82 mm diameter. E-64

34 Lever Dial Dial Test Gages Indicators DIN 878, NF E , factory standard 58/82 mm Diameter Dial Gages Series 532, reading to 0.01 mm Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers (models with a 58 mm dial diameter only). M2,5 coupling thread for contact point. Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Serial number Inspection report with a declaration of conformity B: With bezel lock. E: Watertight as per DIN 40050, IP64. G: Large dial having a 82 mm diameter. S: Models with a reduced range, balanced reading. Since the pointer travels less than one revolution, all reading errors due to the revolution counter are eliminated. T: The short pointer, which moves along with the reading pointer, continuously indicates the highest value of the measured quantity. Both are attached in the middle of the dial. Ideal for checking axial and radial runouts. Metric models Total Repeat- Hyste- N reading ability resis mm mm mm mm mm error(μm)μm μm LEFT B B LEFT G GB E S ± (1.27) ST ± (1.27) S ± (1.27) SB ± (1.27) Inch models Total Repeat- Hyste- N reading ability resis in mm in in in error (in) in in 533A AB AG AGB AE AS ± (.050) ASB ± (.050) E-65

35 Dial Gages 58/82 mm Diameter Dial Gages Series 550, reading to 0.002/0.001 mm DIN 878, NF E , factory standard Rotating dial 129) Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers (models with a 58 mm dial diameter only). M2,5 coupling thread for contact point. Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Metric models Total Repeat- Hyste- N reading ability resis mm mm mm mm mm error(μm) μm μm B E G GB B E G GB Inch models Serial number Inspection report with a declaration of conformity E-66 Total Repeat- Hyste- N reading ability resis in mm in in in error (in) in in 555A AB AE AG AGB A AB AE AG AGB B: With bezel lock. E: Watertight as per DIN 40050, IP64. G: Large dial having a 82 mm diameter.

36 Lever Dial Dial Test Gages Indicators DIN 878, NF E , factory standard Rotating dial 58/82 mm Diameter Dial Gages Series 560, reading to 0.002/0.001 mm Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers (models with a 58 mm dial diameter only). M2,5 coupling thread for contact point. Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Serial number Inspection report with a declaration of conformity Metric models 5 B: With bezel lock. E: Watertight as per DIN 40050, IP64. G: Large dial having a 82 mm diameter. S: Models with a reduced range, balanced reading. Since the pointer travels less than one revolution, all reading errors due to the revolution counter are eliminated. Total Repeat- Hyste- N Reading ability resis mm mm mm mm mm error(μm) μm μm 565S ± (0.2) SB ± (0.2) SE ± (0.2) B E S ± (0.1) SB ± (0.1) SE ± (0.1) SG ± (0.1) Inch models Total Repeat- Hyste- N Reading ability resis in mm in in in error (in) in in 567A AB AE AS ± (.005) ASB ± (.005) ASE ± (.005) E-67

37 Dial Gages 58/82 mm Dial Gages with Long Range, Series 700 DIN 878, NF E , factory standard Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Ajustable tolerance markers (models with a 58 mm dial diameter only). M2,5 coupling thread for contact point. Revolution counter in the middle Contact point with a 3 mm dia. ball tip, already mounted Cardboard box Serial number Inspection report with a declaration of conformity 58 mm 82 mm 58/82 mm 30 mm 30 mm 50 mm 100 mm 150 mm 200 mm mm 1 in 1 in 2 in 4 in 6 in 8 in A B C D E F 8h6 8h6 8h6 8h E-68

38 Lever Dial Dial Test Gages Indicators Reading to 0.1 mm Metric models Total Repeat- Hyste- N Reading ability resis mm mm mm mm mm error(μm) μm μm B G GB B G GB B G GB Reading to 0.01 mm Metric models Total Repeat- Hyste- N Reading ability resis mm mm mm mm mm error (μm) μm μm B B LEFT G GB B B LEFT G GB B G GB G G Inch models B: With bezel lock. G: Large dial having a 82 mm diameter. Total Repeat- Hyste- N Reading ability resis in mm in in in error (in) in in 713A AB AG AGB A AB AG AGB A AB AG AGB E-69

39 Dial Gages Dial Gages with electrical contacts, Type CL Type CL2 Consists of a mechanical dial gage combined with an element featuring 2 electrical contacts. Can be used in conjunction with the amplifying unit R43 (No ). Type CL4 Measuring unit with the following components included: Mechanical dial gage. Element fitted with 2 electrical contacts for setting tolerances. Electronic amplifying unit controlling 3 color signals for value classification with red for scrap, green for good and yellow for rework. Power supply: 12 V AC through the R13 type transformer. Factory standard Rotating dial Full-metal housing. Plunger and stem with a 8h6 dia. in stainless steel, hardened and ground Shockproof system to protect the movement Adjustable tolerance markers on models with a 58 mm dia. dial. M2,5 thread for contact point. Revolution counter in the middle Contact point with a 3 mm dia. ball tip, already mounted Contact accuracy: 0,001 mm. Current passing through the contacts: 10 μa, 12 V. Response time: 0,1 s. Power supply for CL4: 12 V, 50 Hz, 60 ma Cardboard box Serial number Declaration of conformity E-70 CL2