USB Type-C Design Implementations Overview & Test Solution. Seo Dong-Hyun

Transcription

1 USB Type-C Design Implementations Overview & Test Solution Seo Dong-Hyun

2 USB Type-C Overview

3 What is the USB Type-C Connector? One connector to rule them all Original USB Industry Drivers Single connector type/expandability Performance/Speed Power Ease of Use for End-User Type-C Industry Drivers Broad application in standards 10 Gb/s with path to 40 Gb/s Can handle 5 Amps at 20Volts Reversible (can be flipped) Page 3

4 The Communications Ecosystem Where does USB-C fit? Chipsets & Components Handsets & Devices Base Stations & Broadband Network Infrastructure Data & Cloud Computing 2G/3G/4G Base Stations Small Cells Switches/ Routers Long-haul Optical Networks Enterprises Data Centers Type-C Page 4

5 Why Does It Matter? Simplicity and Capability to consumer. Complexity to Designers, Integrators, and Validators Speed Speeds of the Future and Backwards Compatibility Power Up to 100 W Power direction no longer fixed Standards Integration Page 5

6 USB Type C Signal Plan High Speed Lanes B12 A1 4 High Speed Lanes: Up to 20Gbs each RX1 RX1 TX1 TX1 Port 1 V BUS V BUS SBU2 CC1 D- D+ CC2 + D+ D- SBU1 V BUS V BUS TX2 TX2 RX2 RX2 Port 2 B1 A12 Page 6

7 USB Type C Signal Plan Power Pins B12 A1 RX1 TX1 RX1 TX1 V BUS V BUS SBU2 CC1 D- D+ D+ D- CC2 SBU1 Power Pins 4 4 Supply Pins Handles up to 5 amps V BUS TX2 TX2 V BUS RX2 RX2 B1 A12 Page 7

8 USB Type C Signal Plan Sideband Use Pins B12 A1 RX1 TX1 RX1 TX1 V BUS V BUS SBU2 CC1 D- D+ D+ D- CC2 SBU1 V BUS TX2 TX2 V BUS RX2 RX2 SBU lines: Extra lines for alternate use B1 A12 Page 8

9 USB Type C Signal Plan USB2.0 Pins B12 A1 RX1 TX1 RX1 TX1 V BUS V BUS SBU2 CC1 D- D+ CC2 x D+ D- SBU1 USB2 lines: USB2 operation Link Communication V BUS V BUS TX2 RX2 TX2 RX2 B1 A12 Page 9

10 USB Type C Signal Plan CC Pins B12 A1 RX1 TX1 RX1 TX1 V BUS V BUS SBU2 CC1 D- D+ D+ D- CC lines for: Configuration Mngmt, Supply Power to Cable Power Delivery Communication CC2 SBU1 V BUS V BUS TX2 RX2 TX2 RX2 B1 A12 Page 10

11 USB Type C Port Function USB3.1 & USB2.0 B12 A1 Alt STD USB3.1 Operation STD Mux Port Mux RX1 TX1 RX1 TX1 V BUS V BUS SBU2 CC1 D- D+ USB2.0 Operation D+ USB 3.1 D+ D- CC2 SBU1 V BUS V BUS D- USB 2.0 TX2 RX2 Product TX2 RX2 B1 A12 Page 11

12 USB Type C Port Function Power Lines B12 A1 Supply RX1 RX1 TX1 TX1 Provider/ Consumer V BUS SBU2 V BUS CC1 D- D+ D+ D- Power (V BUS ) Control & Alt Mode CC2 V BUS SBU1 V BUS TX2 RX2 TX2 RX2 B1 A12 Page 12

13 USB Type C Port Function SBU Lines (Sideband Use) SBU lines NOT used in USB3.1 Become active in alternate mode only to support the alternate technology. RX1 RX1 B12 TX1 TX1 A1 DisplayPort SBU1 -> AUX + SBU2 -> AUX - V BUS V BUS SBU2 CC1 D- D+ D+ D- MHL SBU1 -> e-cbus-s SBU2 -> e-cbus-s Thunderbolt CC2 V BUS SBU1 V BUS SBU1 -> LSRX SBU2 -> LSTX TX2 TX2 RX2 RX2 B1 A12 Page 13

14 USB Type C Port Function CC Lines (Configuration Channel) CC1 and CC2 Sensed for Termination: If cable termination (R A ) is present at CCn Then CCn=>V CONN RX1 RX1 V BUS SBU2 TX1 TX1 V BUS CC1 D- D+ CC2 B12 D+ D- SBU1 A1 R P V C CC Downstream Facing Port (Host) V sense_d V Conn Cable-End Circuitry R A B1 V BUS TX2 TX2 V BUS RX2 RX2 A12 Page 14

15 USB Type C Port Function CC Lines (Configuration Channel) CC1 and CC2 Sensed for Termination: If cable termination (R A ) is present at CCn Then CCn=>V CONN Else When Link partner terminated then Port orientations are known and CC Line becomes the power delivery channel. B1 RX1 RX1 V BUS SBU2 TX1 TX1 V BUS CC1 D- D+ CC2 V BUS TX2 TX2 B12 D+ D- SBU1 V BUS RX2 RX2 A1 A12 R P V C CC R D Downstream Facing Port (Host) V sense_d1 V sense_u1 V CONN Cable-End Circuitry R A R A V CONN Page Cable-End Circuitry Device (Upstream Facing Port) 15

16 USB Type C Port Function Port Configuration V C R P V sense_d Port Mux Port Mux CC V CONN R A R A R D V sense_u1 V CONN Downstream Facing Port Cable Upstream Facing Port Page 16

17 USB Type C Port Function Port Configuration (Cable Flip at UFP) V C R P V sense_d Port Mux Port Mux R A CC V CONN V CONN R A R D V sense_u2 Downstream Facing Port Cable Upstream Facing Port Page 17

18 USB Type-C PD (Power Delivery) Validation Solutions

19 USB Power Delivery Example Only 1 traditional wall power cord Power Data SSD Page 19

20 USB-PD Specification Test Plan Three Test Sections Page 20

21 Chapter 5: Physical Layer Test (Provider/Consumer) USB-PD Coupon(s) Passive Probe GRL-USB-PD-C Controller Page 21

22 USB-PD Device Testing using N8840A Test setup Dual Role Devices (P/C or C/P) Requires electrical load (eload) and current probe for load test SMPS Power Adapter will be sufficient however an external power supply is recommended if a clean power source is needed for Vconn Page 22

23 N8840A USB-PD Electrical and Protocol Compliance Test Software Power Delivery Compliance Testing Runs on Infiniium based oscilloscopes S-Series recommended for hardware protocol trigger Performs BMC-PHY Compliance tests Performs BMC-PROT Compliance tests Performs BMC-POW Compliance tests Automates Compliance tests when used with Type-C Test Controller Developed in partnership with GRL (Granite River Labs) Page 23

24 USB-PD Device Testing using N8840A Compliance Test Results Page 24

25 PD Compliance Test Configuration Dual Role Port (DRP) Test (GRL-USB-PD-C1) eload Mainframe 250W eload Module USB/GPIB Cable (USB3.1-C-PDC) Page 25

26 N8837A USB-PD Protocol Trigger and Decode Keysight Power Delivery protocol decode and hardware triggering with S-Series USB PD CC and Vbus line signal USB PD protocol decoding window example Hardware serial trigger in S-Series Page 26

27 USB 3.1 Overview

28 USB 3.1 Gen1 and Gen2 2.2 db -3.1 db GHz Page 28

29 USB 3.1 LTSSM TX compliance mode RX compliance mode - loopback Page 29

30 USB 3.1 Compliance Patterns Page 30

31 USB3.1 Channel Budget Host Device chip Host Routing Cable characteristics Device routing chip Ic pins Connector Type Connector Type Ic pins Loss at Nyquist is identified here. Channel Models (s-parameters) required. Page 31

32 USB 3.1 Type-C TX Test Solutions

33 USB 3.1 gen2 10Gb/s USB 3.1 Type C Fixture Kit rev 2 HW channel Page 33

34 Testing USB 3.1 TX w/type C TX RX Mux TX0 RX0 TX1 RX1 Vbus Switch Matrix Short Channel Model Host Long Channel Model SCD1, SCD2, Ping Type C SigTest Power Delivery Controller Cc Line Orientatin Vconn,, Connection Downstream Facing Port PING LFPS Toggles CMM C New TPA BW=20GHz? Page 34

35 High level Test Setup for USB C-Connector Power and signal control for N7016A Page 35

36 N7015A Type C Test Fixture High speed coax cables, Matched pairs for TX2+, TX2-, RX2+, RX2- Type C plug connection to DUT (receptacle) 2 pin header for SBU1 and SBU2 test points Vbus and CC lines to N7016A fixture via USB Type C (plug style) cable USB2.0 D+ and D- High speed coax cables, Matched pairs for TX1+, TX1-, RX1+, RX1- High speed (TX/RX) and D+/D- lanes to scope through coax cables N7015A de-embedding models will be created and integrated in to compliance applications and Infiniium baseline software Power and Control signals to low speed N7016A fixture though type C cable View SBU1/2 signals Page 36

37 N7016A Type-C low speed signal access and control fixture Connects to N7015A through a captive C type cable (port 1) conveying CC 1, CC 2, SBU1, SBU2, V BUS and Controls to terminate CC 1, CC 2 independently (Ra, Rp, Rd) Control to load Vconn (2 different loadings possible) External power for power consumers Type C receptacle to plug into other devices or cables (port 2) USB2.0 interface for external control from application or standalone SW on a PC Page 37

38 U7243B USB 3.1 TX Compliance Application Keysight solution features: Support USB3.1 Gen1/Gen2 USB-IF Sigtest & Keysight SDA algorithm CTLE Adc scan Support live & saved waveform USB-IF and customer s embedded transfer function External instrument for triggering SCD1/2, LBPM and toggle Compliance Pattern Page 38

39 U7243B USB 3.1 TX Compliance Application Gen 1 test items, LFPS, SSC, eye mask, Jitter Gen2 LFPS, trepeat, tburst, tpwm, tlfps_0, tlfps_1 SSC test items Select/Scan for optimal Adc of CTLE Eye mask and Jitter test by SDA algorithm Eye mask and Jitter test by SigTest algorithm Page 39

40 N8821A/B USB 3.1 Gen1/Gen2 Protocol Trigger and Decode USB 3.1 Gen1 and Gen 2 protocol decode in less than 30 seconds Integrated software-based protocol-level triggers Save time and eliminate errors by viewing packets at the protocol level Use time-correlated views to quickly troubleshoot serial protocol problems back to their timing or signal integrity root cause Page 40

41 USB 3.1 Type-C RX Test Solutions

42 USB 3.x Comparison USB 3.0 (aka USB 3.1 Gen 1 PHY) USB 3.1 (aka USB 3.1 Gen 2 PHY) Data rate 5Gb/s ±300ppm (SSC variations not accounted for) Coding 8b/10b scrambler: G(X) = X 16 + X 5 + X 4 + X scrambler reset by COM (K28.5) or BRST seed: FFFFh Symbol lock: K28.5, some implementations might be able to use K28.1or K Gb/s ±300ppm (SSC variations not accounted for) 128b/132b scrambler: G(X) = X 23 + X 21 + X 16 + X 8 + X 5 + X scrambler reset by SYNC OS seed: 1D BFBCh Block alignment: SYNC OS + SDS OS and realignment thr ough SKP OS SKP K28.1, K28.1 SKP OS with variable number of SKPs LFPS CDR PLL transfer: f 3dB = 10MHz peaking max = 2dB HPF transfer: f 3dB = 4.9MHz peaking 0dB damping factor = SSC Modulation rate: 30kHz to 33kHz Deviation: +0 to -4000(min)/-5000(max) Max slew rate: 10ms/s De-emphasis Post: -3dB Pre: 2.2dB Post: -3.1dB Device host capability negotiation is done during Low Frequen cy Periodic Signaling (LFPS) phase using LFPS modulation s chemes PLL transfer: f 3dB = 15MHz peaking max = 2dB HPF transfer: f 3dB = 7.5MHz peaking 0dB damping factor = Modulation rate: 30kHz to 33kHz Deviation: +0 to -4000(min)/-5000(max) New df/dt requirement: 1250 (max) ppm/μs instead of max slew rate spec Page 42

43 Typical USB 3.0 Link Turn-on Sequence LTSSM states: Host Power-up Rx. Detect. Reset Rx. Detect. Active Polling. LFPS Polling. RxEQ Polling. Active Polling. Configuration Polling. Idle Loopback warm reset de-assert termination detected LFPS handshake TSEQ transmitted TS1 received TS2 received if directed Device Compliance warm reset Rx. Detect. Reset Rx. Detect. Active Polling. LFPS Polling. RxEQ Polling. Active Polling. Configuration Polling. Idle Loopback multiple states Power-up J-BERT s sequence trigger can be used to trigger scope captures for each trainings step in combination with scope s protocol decode very helpful for debugging a trainings sequence Page 43

44 Typical USB 3.1 Link Turn-on Sequence LTSSM states: Powerup warm reset Rx. Detect. Reset Rx. Detect. Reset warm reset de-assert Rx. Detect. Active Rx. Detect. Active termination detected Polling. LFPS Polling. LFPS SCD1 LFPS handshake Polling. LFPS Plus Polling. LFPS Plus SCD2 LFPS handshake Polling. Portmatch Polling. Portmatch PHY Capability LBPM handshake Polling. Port Config Polling. Port Config PHY Ready LBPM handshake Polling. RxEQ TSEQ transmitted Polling. RxEQ Polling. Active Polling. Active TS1 received Polling. Configuration TS2 received Polling. Idle Polling. Idle if directed Polling. Configuration Loopback Loopback Compliance Powerup multiple states J-BERT s sequence trigger can be used to trigger scope captures for each trainings step very helpful for debugging a trainings sequence Page 44

45 Scope J-BERT USB 3.0/3.1 5Gb/s RX Test Calibration Compliance Test Channel Type-C Connector 1m cable with USB Type-C connectors Type-C to Type C board Cal fixture CLB V bus Same setup for host or device with exception of Type-C to Type-C board: Host RX breakout for DUT TX to BERT RX channel, no V bus connection Host TX no breakout, no V bus connection Device RX breakout for DUT TX to BERT RX, V bus connection Device TX no breakout, no V bus connection Exact trace length of CLB is not defined yet 1m cable with USB Type-C connectors Page 45

46 USB 3.1 gen2 10Gb/s USB 3.1 Type C 23dB Cal Channel CLB Scope J-BERT 1m cable with USB Type-C connectors Type-C to Type C board Mock host / device Compliance Load Board (CLB): A fixture set contains three CLBs with traces of different lengths to be able to adjust residual ISI Four versions of Type-C to Type-C board: Host RX breakout for DUT TX to BERT RX channel, no V bus connection Host TX no breakout, no V bus connection Device RX breakout for DUT TX to BERT RX, V bus connection Device TX no breakout, no V bus connection Mock-Up fixture: Simulates reference device/host loss. Used for calibration only. Page 46

47 J-BERT PG USB 3.1 gen2 10Gb/s USB 3.1 Type C 14.5dB Test Channel J-BERT ED V bus DUT Unlike for USB 3.0/3.1 gen1 5G RX testing USB 3.1 gen2 10G RX compliance testing requires to test each test frequency for bits. Page 47

48 Testing USB 3.1 RX w/type C Controller TX RX Mux TX0 RX0 TX1 RX1 Vbus Switch Matrix Host Channel Error Detector Pattern Generator Type C Power Delivery Controller Cc Line Orientatin Vconn,, Connection Downstream Facing Port Page 48

49 USB 3.1 Gen1/Gen2 Receiver Test Setup Key capabilities: Analysis of coded & retimed data Support of 8b/10b and 128b/132b HW coding and decoding as well as HW scrambling Generates calibrated stress conditions for RX test (SSC, SJ, RJ, De-emphasis, ISI) Emulate LFPS 3-level signals with built-in electrical idle for loopback training and via channel Integrated Link Training, Tx Eq, Noise Impairment, Variable ISI, Receiver Equalizer/Eye Opener Page 49

50 N5990A Test Automation for USB Test Overview Compliance Tests: 5G RX Compliance long channel 5G RX Compliance short channel 5G RX Compliance LFPS 10G RX Compliance position 1 10G RX Compliance position 2 Characterization Tests: RX constant parameter RX jitter tolerance (SJ margin) RX and LFPS sensitivity RX data rate deviation LFPS Duty Cycle Page 50

51 N5990A Test Automation for USB 3.0/3.1 Ease of Use The N5990A Test Automation for USB 3.0/3.1 guides users through every setup changes with connection diagrams and detailed descriptions Page 51

52 Receiver Jitter Tolerance curve Gen1 vs Gen2 Rx Jtol RJ & Tx EQ updated by ECN Gen 2 define 7 SJ points in spec. Gen 1 define 5 SJ points in Spec, but 8 points in CTS (0.5MHz, 2.56) (0.5MHz, 2) (1MHz,0.1.28) (1MHz,1) (2MHz,0.64) (2MHz,0.5) (4MHz,0.32) RJpp 0.17 UI (4.9MHz,0.2) (50MHz,0.2) 0.14 UI RJpp (50MHz,0.17) (7.5MHz,0.17) (100MHz,0.17) Page 52

53 SuperSpeed Receiver Tests Rx Compliance and Jitter Tolerance Testing Automated instrument control for: Setup calibration Compliance test Characterization test Support for debugging Operator guidance Sophisticated test reports Controls J-BERT, Oscilloscope. Supports full product characterization including transmitter measurements Page 53

54 JTOL Margining Test Results Page 54

55 Receiver Characterization Example Automated instrument control for: Setup calibration Compliance test Characterization test Support for debugging Operator guidance Sophisticated test reports Controls J-BERT, Oscilloscope. Supports full product characterization including transmitter measurements Page 55

56 Keysight USB 3.1 Total Test Solution Transmitter Test Interconnect Test Receiver Test SW U7243B USB Compliance Test Software N5990A USB Compliance Test Software HW DSAV254A Infiniium Scope E5071C ENA Option TDR M8020A J-BERT High- Performance Serial BERT Fixture DUT N7015A/16A Tx Test Fixture Tx TBD Cable/Connector Test Fixture Cable TBD Rx Test Fixture from USB-IF Tx Rx Page 56

57 USB Type-C Interface and DP Alt Mode Overview

58 Review of DisplayPort Interface Data Ck Level Policy Mgr Tx DisplayPort Source Main Link PE Logic 4 Differential Lanes AUX Main Link Hot Plug Detect Up to 4 differential lanes: 4 possible bit rates TX: 4 possible level settings 4 possible pre-emphasis settings Spread Spectrum Clocking (optional) Dual Mode optional RX: Receiver individual clock recovery Receiver Tolerance curve specified. Receiver Sensitivity = 50mV 1 Differential Lane Bit Recovery DPCD EDID Data Interrupt DisplayPort Sink AUX Channel Phy Layer Bit rate at 1Mbs Manchester II encoded Purpose Link Management Test Mode control Page 58

59 DP USB Type C Port Function Alternate Mode: DisplayPort Downstream Facing Port (Video Output) STD Mux Port Mux Cable Provider/ Consumer V Conn V CONN CC USB 3.1 Supply Provider/ Consumer Port Mux Upstream Facing Port (Display) Page 59

60 DP Transmitter Testing: Whole Channel DUT Cable Model Sink Data Ck Level Driver Tx PE Logic Decode REFERENCE EQUALIZER Eye DisplayPort Source Standard DP mdp USB Type C Cable Loss Model CTLE DFE (50mv max) TP2 TP3 TP3EQ TP3EQ Math performed on oscilloscope on TP2 acquisition Page 60

61 TX Test Setup for DP over USB Type-C Keysight TPAs High Speed Phy test AUX Phy test Connector: Type C N7015A Fixtures N7016A USB C to DP cable Unigraf DPR-100 AUX Automation Keysight TPAs High Speed Phy test AUX Phy test Connector: Type C N7015A Fixtures N7016A USB C cable Power Delivery Controller AUX Automation Page 61

62 RX Test Setup for DP over USB Type-C InterSymbol Interference High Speed Phy test N7015A N7016A Unigraf DPT-200 USB C to DP cable AUX Automation Page 62

63 Keysight DisplayPort 1.3 Solutions and Solution Elements Source Test Solution Media Testing Sink Test Solution Link Layer & General Solutions Computer Motherboards, ICs, Graphic Cards Cables, PC Boards, Connectors PC Monitors Protocol Debug solution DSO V series Infiniium Real Time Oscilloscopes Artek CLE1000 M8020A JBERT Unigraf DPR-100 For automation U7232D DisplayPort Compliance Test SW E5071C VNA Unigraf DPT-200 N4915A-006 for Automation DP ISI Generation STD/mDP USB C Granite River Labs GRL-DP-DEC STD/mDP USB C STD/mDP USB C BIT-DP-RTF-0002 Luxshare Rec Wilder TPA N7015A TPA BIT-DP-CBL-0002 Luxshare Rec N5990A Rx Compliance Test SW Wilder TPA N7015A TPA Page 63

64 USB Type-C Interface and TBT Alt Mode Overview

65 Thunderbolt 3 Overview Announced in Q Uses the Type-C connector Channel aggregation: two independent 20Gbps links into one logical 40Gbps link Supports other standards through ALT mode Page 65

66 Testing Methodology Spec is at v0.7. CTS not yet released. Testing approach will be similar to Thunderbolt 2 Tx, Rx, and Return Loss Today, customers with Thunderbolt DUTs need to work with their Inte l PAE to meet the design guidelines and send their DUTs to Intel for t esting. Keysight can help with pre-compliance testing Tx testing Initial analysis is that 33GHz minimum BW is required for compli ance testing. Silicon characterization will need more BW since the 20/80 riseti me can be 10ps. Page 66

67 Thunderbolt 3 Transmitter Test Setup 25GHz BW required for compliance testing, more if closer to the silicon Thunderbolt-specific SW (Imaginarium, TenLira, TCL, scripts) Crosstalk generator Type-C test fixture UI, SSC, Rise/Fall, Jitter, Eye Diagram Near End/Far End New Preset testing and optimization for 10.3G and 20.6G Page 67

68 Thunderbolt 3 Return Loss Test DUT output PRBS31 on all lanes with SSC turned on Setup the Network Analyzer with automated measurements specific to Thunderbolt 3 Page 68

69 Test Setup: Case 1 and Case 2 Execution Common Mode Controller USB USB Aggressor DUT Common Mode Controller USB USB Aggressor TBT3 Cable DUT Page 69

70 Thunderbolt 3 Total Solution Transmitter Test Return Loss Test Receiver Test SW Thunderbolt Transmitter Test Software N5990A Automatic SW for TBT compliance HW TBT-TPA- UGH2 Controller V-Series Infiniium Oscilloscope E5071C Option TDR ENA Network Analyzer or 86100D DCA-X M8020A J-BERT High- Performance Serial BERT M8062A 32 Gb/s Multiplexer with De-emphasis TBT-TPA-UGH2 Controller N5171B Common Mode Source Fixture Fixture Fixture Fixture DUT Tx Cable Rx Error counter Page 70

71 Page 71