1. Install Programmer Software
|
|
- Erik Sparks
- 6 years ago
- Views:
Transcription
1 Notes: Uses IST A Programming Pod and 12-position 1 mm flat flex cable. If you encounter any problems while trying to program your unit, please contact Rebecca Afzal via or call x Install Programmer Software 1.1. Install Quartus II Stand-Alone Programmer Before connecting the Programming Pod to the computer, begin by downloading and installing the Altera Quartus II Stand-Alone Programmer. You will need to create an Altera account to access the software via the link below: Once the program is finished downloading proceed with installing it. Page 1 of 12
2 Page 2 of 12
3 Once the Altera programming software has finished installing, plug the Programming Pod into the computer's USB port. Then open the Device Manager and you should see the Altera USB- Blaster as an uninstalled device. Right click it and select 'Update Driver Software...' to install the programmer driver. If the driver automatically installs then the driver doesn t need to be manually updated. Select the option to 'Browse my computer for driver software' and navigate Altera program Navigate to the Altera USB-Blaster Driver folder shown below. Once you locate the driver folder continue through the windows driver install. When the driver has been installed the Altera USB-Blaster will show up as a USB device in the device manager. Page 3 of 12
4 1.2. Install SiLabs Flash Utility After the Altera programming software and drivers are installed, download the SiLabs Flash Utility from the link below. Page 4 of 12
5 Run the file to install the program. 2. VectorVGA Board Programming Procedures Warning: power must be off when connecting or disconnecting the Programming Pod to the VectorVGA display. Do not touch any high-voltage components (e.g., power entry module, power switch, line wiring, power supply module, etc.) while the cover is removed. Each display unit has two FPGA/MCU boards that are accessible either via a remote programming port on the back of the unit or by removing the enclosure cover. Each board has one Altera FPGA and one SiLabs MCU that are separately programmed. The Programming Pod can program the FPGA and MCU devices on one board through the flex cable. Please refer to Appendix B to identify the programming port, and to locate the programming headers for FPGA #1 and FPGA #2, if the unit has no programming port see Appendix C to identify Board #1 and Board #2, and to locate the programming header on each board SiLabs Flash Utility With the VectorVGA Pro unit off, connect the 12-position flat flex cable from the Programming Pod to the programming port of the desired board (FPGA #1 or FPGA #2), with the metal contacts on the cable facing the metal prongs of each connector (i.e., it is easy to insert flex cables backwards; no damage is done but the programmer won t work). Ensure the Programming Pod is plugged into the computer's USB port. Turn display power on when the Programming Pod is completely connected. Run the Flash Utility, and then select 'Connect'. If you have a connection problem make sure the flex cable is plugged in properly and the display power is on. Page 5 of 12
6 Change tab to 'Download Hex File/Go/Stop', Click 'Browse' and navigate to the supplied hex file and open. FIRM xxx.hex Check the box for 'Erase all Code Space before download' and click 'Download'. Press 'OK' at the warning box Cycle power on the display and the MCU firmware is installed. Page 6 of 12
7 2.2. Altera FPGA Programming Procedure Starting with the Programming Pod connected and display power turned on. Open the Altera Quartus II Programmer. The first step is to set up the programming hardware. (I.e. the USB-Blaster) Make sure that the JTAG mode is selected and click the 'Hardware Setup...' button. Select the USB-Blaster from the drop down menu and click close. Then click 'Add File...' and select the.jic file supplied by IST. FIRM xxxx.jic Page 7 of 12
8 Once the file is loaded check the 'Program/Configure' and 'Verify' check boxes and click the start button to begin programming. When the programming has completed the top status bar and bottom message window will indicate that the programming has been successful. Page 8 of 12
9 If you receive an error message, check the VectorVGA Pro's power, the flat flex cable and the USB connection. Example Error Message When programming is successful, cycle power on the VectorVGA Pro display to restart the system with the new FPGA firmware. If the firmware number on the splash screen has been changed, this can be verified by turning DIP Switch #1 on for the board that was programmed. The splash screen will show the loaded firmware version. Turn DIP Switch #1 off when done. Page 9 of 12
10 Appendix A: Firmware Cross Reference P/N Description Board No. Device F/W 1 FPGA FIRM C IST C HP 1332A A/R-Scope for MOTR 1 MCU FIRM F 2 FPGA FIRM D 2 MCU FIRM F 1 FPGA FIRM B IST A HP 1304A 10-Trace for MOTR 1 MCU FIRM A 2 FPGA FIRM C 2 MCU FIRM A 1 FPGA FIRM A IST A HP 1311A with Overlay 1 MCU FIRM A 2 FPGA FIRM B 2 MCU FIRM A Page 10 of 12
11 Appendix B: Programming Port Header Reference The purpose of this appendix is to identify the programming port and the proper connectors to use for programming each FPGA/MCU board. The programming port can be accessed by removing the metal covering plate which is held down by 2 Phillips head screws. Once the cover is removed the programming headers can be seen. The programming header for FPGA #1 is labeled 1 and the programming header for FPGA #2 is labeled 2. Simply connect the programming pod to each FPGA via the available headers to program the system. Be sure the insert the flat flex cable with the metal tabs facing up into the metal prongs of the connectors. Page 11 of 12
12 Appendix C: Board Programming Header Reference The purpose of this appendix is to identify the programming header on each FPGA/MCU board, and identify Board #1 and Board #2. Note: actual systems may be slightly different than the picture above. Location of Programming Header: Both FPGA/MCU Boards have a header that is labeled JTAG as shown above. This header connects to the Programmer Pod (warning: connect and disconnect only when display is powered off). How to Identify Board #1 and Board #2: Board #1 Board #2 The picture above identifies Board #1 and Board #2, and a short description is given below: Both boards have an identical FPGA section (see the large square black IC), although they may be populated slightly differently. Board #1 is the larger board. Analog signals enter on the left side through one flex cable, and digital signals output to Board #2 through two flex cables. Board #2 is the smaller board. Digital signals from Board #1 enter on the left side through two flex cables, and digital video outputs to the LCD adapter board on the right through two flex cables. Page 12 of 12
Configuration and programming minimodules MMfpga01 and MMfpga11
MMfpga01 MMfpga11 Configuration and programming minimodules MMfpga01 and MMfpga11 1 Index 1. Instalation of the QUARTUS II Web Edition...3 2. How to install QUARTUS II Web Edition...5 3. Installation of
More informationULTIMATE CART FIRMWARE UPGRADE GUIDE
Page 1 ULTIMATE CART FIRMWARE UPGRADE GUIDE This guide is intended as a reference to help understand the firmware upgrade process for the Ultimate Cart and highlight potential issues. It is not a comprehensive
More informationCSE P567 - Winter 2010 Lab 1 Introduction to FGPA CAD Tools
CSE P567 - Winter 2010 Lab 1 Introduction to FGPA CAD Tools This is a tutorial introduction to the process of designing circuits using a set of modern design tools. While the tools we will be using (Altera
More informationNOTE: This tutorial contains many large illustrations. Page breaks have been added to keep images on the same page as the step that they represent.
CSE 352 Tutorial # 4 Synthesizing onto an FPGA Objectives This tutorial will walk you through the steps of implementing a design made in Active-HDL onto the Altera Cyclone II FPGA NOTE: This tutorial contains
More informationCHAPTER 1 Introduction of the tnano Board CHAPTER 2 tnano Board Architecture CHAPTER 3 Using the tnano Board... 8
CONTENTS CHAPTER 1 Introduction of the tnano Board... 2 1.1 Features...2 1.2 About the KIT...4 1.3 Getting Help...4 CHAPTER 2 tnano Board Architecture... 5 2.1 Layout and Components...5 2.2 Block Diagram
More informationNIOS CPU Based Embedded Computer System on Programmable Chip
1 Objectives NIOS CPU Based Embedded Computer System on Programmable Chip EE8205: Embedded Computer Systems This lab has been constructed to introduce the development of dedicated embedded system based
More informationAn ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT
INSTRUCTION MANUAL 1. DESCRIPTION KEPCO An ISO 9001 Company. BOP 1KW-MG FIRMWARE RETROFIT KIT BOP 1KW-MG RETROFIT KIT 219-0621 Kepco KIT 219-0621-(n) contains the parts used to upgrade the firmware for
More informationBoard Update Portal based on Nios II Processor with EPCQ (Arria 10 GX FPGA Development Kit)
Board Update Portal based on Nios II Processor with EPCQ (Arria 10 GX FPGA Development Kit) Date: 1 December 2016 Revision:1.0 2015 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, HARDCOPY,
More informationInstructions for Installing FlashUpdate and Downloading Updates for Super Buddy Satellite Meter
Instructions for Installing FlashUpdate and Downloading Updates for Super Buddy Satellite Meter Updates to the Field Guide and to the instrument firmware are available from the Applied Instruments website.
More informationEARTH PEOPLE TECHNOLOGY. ODIN-LINK BLE + MAXPROLOGIC Development System User Manual
EARTH PEOPLE TECHNOLOGY ODIN-LINK BLE + MAXPROLOGIC Development System User Manual This User Manual covers the Odin-Link and MaxProLogic Development System. The Odin-Link board includes the Texas Instruments
More informationInstallation of advanced communications board and LG Chem RESU
Installation of advanced communications board and LG Chem RESU Introduction This technical note shows how to set up an SP PRO for use with an LG Chem RESU lithium battery. It explains how to update the
More informationUniversal CCU CAT-5 Release Notes
BLURB Release Notes Universal CCU CAT-5 Release Notes Release Version: V 1.01.16 Release Date: 10/30/2014 Component Version Hardware -327A PIC 1.01.16 FPGA update not needed in this release New Features
More informationLab 2 EECE473 Computer Organization & Architecture University of Maine
Lab 2: Verilog Programming Instructor: Yifeng Zhu 50 Points Objectives: 1. Quatus II Programming assignment: PIN assignments, LEDs, switches; 2. Download and test the design on Altera DE2 board 3. Create
More informationChapter 2: Hardware Design Flow Using Verilog in Quartus II
Chapter 2: Hardware Design Flow Using Verilog in Quartus II 2.1 Introduction to Quartus II System Development Software This chapter is an introduction to the Quartus II software that will be used for analysis
More informationHow to Update Firmware & HTML ipower Generation 2
How to Update Firmware & HTML ipower Generation 2 You will need the following 3 files in order to update the firmware and HTML 1. PDU_Bootloader.exe (Windows executable program used to load firmware into
More informationELAD FDM-DUO User Manual - Rev /2016
8 Firmware update This section describes how to update the various firmware of the FDM-DUO. The latest firmware versions are available here: http://sdr.eladit.com/fdm-duo/firmware Releases/. TO FACILITATE
More informationHPSDRProgrammer_v2 v2.0. Apache 10/100/100D
HPSDRProgrammer_v2 v2.0 Quartus-II Programmer ByteBlaster instructions for Apache 10/100/100D 1 of 11 Table of Contents Loading FPGA code with HPSDRProgrammer_v2 v2.0...3 Installing OpenHPSDR's K0VS HPSDRProgrammer_V2:...3
More informationTypical applications where a CPLD may be the best design approach:
By: Carlos Barberis, dba Bartek Technologies Description of Bartek s CPLD1 development board. For some of us CPLD s are familiar devices and for others just another acronym in the electronic device industry.
More informationQuick-Start Guide. BNS Solutions. QSK62P Plus
BNS Solutions Quick-Start Guide QSK62P Plus RS-232 Port Link LED 8-character x 2-line LCD Expansion Port (2) Reset Switch Power LED Thermistor I/O Ring (4) M16C MCU Analog Adjust Pot MCU Crystal Expansion
More informationUpdating your uscope Firmware
2018-08-23 Updating your uscope Firmware Step 1 Update Computer Requirements All uscopes can be updated using a Windows Vista or 7 computer. Only newer uscopes can be updated using a Windows 10 computer.
More informationSound Card Installation for Windows 95/98
Sound Card Installation for Windows 95/98 Hardware Installation 1. Shut down Windows and power down system. Unplug power cable from the system. 2. Remove screws and open system enclosure. 3. Remove static
More informationootbrobotics.com Electronics and Robotics LLC
2 Overview... 3 Device Connections... 3 Installing Drivers... 4 Installing FTDI Drivers... 4 Installing Quartus Drivers... 4 Using the Programmer... 5 Opening the Quartus Programmer Window... 5 Special
More informationMTX-D Ethanol Content and Fuel Temperature Gauge User Manual
MTX-D Ethanol Content and Fuel Temperature Gauge User Manual P/N 3912 kit does not include flex fuel sensor. The ECF-1 is compatible with GM P/Ns 13577429 and 13577379 1. Installation... 2 1.1 Gauge Mounting...
More informationFigure 1. JTAGAVRU1 application The JTAGAVRU1 is supported by AVR Studio. Updated versions of AVR Studio is found on
JTAG AVR Emulator through USB Main Features AVR Studio Compatible Supports AVR Devices with JTAG Interface Emulates Digital and Analog On-Chip Functions Data and Program Memory Breakpoints Supports Assembler
More informationCX1145 MFP - Firmware Updating with USB Storage Device
CX1145 MFP - Firmware Updating with USB Storage Device In this equipment, it is recommended to update the firmware by connecting the USB storage device on which the firmware data is written to the USB
More informationELAD FDM-DUOr User Manual - Rev /2016
8 Firmware Update This section describes how to update the various firmware of the FDM-DUO. The latest firmware versions are available here: http://sdr.eladit.com/fdm-duo/firmware Releases/. TO FACILITATE
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationResolver to Digital Expansion Board
Resolver to Digital Expansion Board Catalog No. EXB009A01 Installation and Operating Manual 6/98 MN1313 Table of Contents Section 1 General Information............................. 1-1 Introduction....................................
More informationapple Service Source Apple Cinema Display 22" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema Display 22" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema Display 22" LCD (ADC) 2003 Apple Computer,
More informationThis document describes the procedure for doing a power trace on the SM5 and Gauntlet Stepmills.
SM5/Gauntlet Stepmill Power Trace Applies to: SM5 (150005) + Gauntlet (150015) This document describes the procedure for doing a power trace on the SM5 and Gauntlet Stepmills. Latest Rev. Warning: the
More informationMotorola Droid X Motherboard Replacement
Motorola Droid X Motherboard Replacement Written By: Yong hoon choun ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 TOOLS: ifixit Opening Tools (1) ifixit CC BY-NC-SA www.ifixit.com Page 2 of 19 Motorola
More informationChapter 2 Getting Hands on Altera Quartus II Software
Chapter 2 Getting Hands on Altera Quartus II Software Contents 2.1 Installation of Software... 20 2.2 Setting Up of License... 21 2.3 Creation of First Embedded System Project... 22 2.4 Project Building
More informationEB020 Installation Instructions.
EB020 Installation Instructions. Detailed below are the 3 steps needed to get up and running with the CPLD board. This 3 step process needs to be completed only once and then the drivers should all be
More informationPF31XX FAMILY FIRMWARE UPDATE GUIDE. v1.2 Revised Nov 29, 2016
PF31XX FAMILY FIRMWARE UPDATE GUIDE Revised Table of Contents 1 Overview... 1 2 Firmware Update Process... 2 3 Document Revision History... 5 Page i 1 Overview This document will assist a user in completing
More informationMotorola Droid X Camera Replacement
Motorola Droid X Camera Replacement Written By: Gage ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 TOOLS: 64 Bit Driver Kit (1) ifixit Opening Tools (1) ifixit CC BY-NC-SA www.ifixit.com Page 2 of 24
More informationECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II This lab manual presents an introduction to the Quartus II Computer Aided Design (CAD) system. This manual gives step-by-step
More informationUniversity of Florida EEL 3701 Dr. Eric M. Schwartz Madison Emas, TA Department of Electrical & Computer Engineering Revision 1 5-Jun-17
Page 1/14 Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate and two inverters under the Quartus environment. Upon completion
More informationHow to Restore a chipkit Bootloader
This guide will show you how to restore your chipkit bootloader, in the event that it has been erased from a chipkit-compatible board. This operation is required if you have used MPLAB X to program the
More informationProgrammer for flash micro computers. User s Manual
Programmer for flash micro computers User s Manual TESSERA Technology INC. 6th edition 9/2008 Table of Contents Chapter 1 Summary 2 1.1 System Configuration 3 Chapter 2 Installation 4 2.1 System Requirement
More informationInstruction Sheet Updating SmartPAC 2 Firmware
Instruction Sheet Updating SmartPAC 2 Firmware This document shows you how to update SmartPAC 2 firmware, using a USB disk, and load SmartPAC 2 firmware installed on a replacement Compact Flash (CF) card.
More informationNIOS CPU Based Embedded Computer System on Programmable Chip
NIOS CPU Based Embedded Computer System on Programmable Chip EE8205: Embedded Computer Systems NIOS-II SoPC: PART-II 1 Introduction This lab has been constructed to introduce the development of dedicated
More information4.1 Design Concept Demonstration for Altera DE2-115 FPGA Board Demonstration for Cyclone III Development Board...
CONTENTS CHAPTER 1 INTRODUCTION OF THE AHA-HSMC... 1 1.1 Features...1 1.2 About the KIT...2 1.3 Getting Help...3 CHAPTER 2 AHA CARD ARCHITECTURE... 4 2.1 Layout and Components...4 2.2 Block Diagram of
More informationDOWNLOADING DESIGNS TO THE ALTERA DE10-LITE FPGA
DOWNLOADING DESIGNS TO THE ALTERA DE10-LITE FPGA Consider the design of a three-bit prime number detector completed in the MSOE schematic entry tutorial. Figure 1 shows the block diagram and truth table.
More informationELAD FDM-DUO Dual Mode SDR Transceiver FIRMWARE UPDATE
ELAD FDM-DUO Dual Mode SDR Transceiver FIRMWARE UPDATE www.eladit.com Contents Revision History... 2 Introduction... 2 1 RX and TX firmware update... 3 1.1 RX firmware update... 4 1.2 TX firmware update...
More informationDaqBoard/3000USB Series USB 1-MHz, 16-Bit Data Acquisition Boards
INSTALLATION GUIDE DaqBoard/3000USB Series USB 1-MHz, 16-Bit Data Acquisition Boards Requires one of the following Operating Systems: Windows 2000 Windows XP Windows Vista Covers 4 Connection Scenarios:
More informationTABLE OF CONTENTS COPYRIGHT INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION
TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3 2. MFP SERVER INSTALLATION...5 PREPARATION...5 CONFIGURATION SOLUTION TABLE...5
More informationEE 231 Fall Lab 1: Introduction to Verilog HDL and Altera IDE
Lab 1: Introduction to Verilog HDL and Altera IDE Introduction In this lab you will design simple circuits by programming the Field-Programmable Gate Array (FPGA). At the end of the lab you should be able
More informationApex-ICE Universal Emulator Hardware and Software Installation Guide
Apex-ICE Universal Emulator Hardware and Software Installation Guide a Notice Analog Devices, Inc. reserves the right to make changes to or to discontinue any product or service identified in this publication
More informationReplacing the Gateway 200ARC Keyboard
Replacing the Gateway 200ARC Keyboard Replacing the Gateway 200ARC Keyboard This package includes a replacement keyboard for your Gateway 200ARC notebook and these printed instructions. Tools you need
More informationQuick Tutorial for Quartus II & ModelSim Altera
Quick Tutorial for Quartus II & ModelSim Altera By Ziqiang Patrick Huang Hudson 213c Ziqiang.huang@duke.edu Download & Installation For Windows or Linux users : Download Quartus II Web Edition v13.0 (ModelSim
More informationMMI6070 Quick Start Guide
MMI6070 Quick Start Guide Introduction If at any time more information is required on HMI safety and protection ratings, HMI Power, and HMI communication, please refer to the MMI6070 Installation Guide
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationLongshine Technologie Europe GmbH
Longshine Technologie Europe GmbH www.longshine.de TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3 2. MFP SERVER INSTALLATION...5
More informationE-bot and E-bot ADV Firmware Upgrade Manual for v1.3.0
E-bot and E-bot ADV Firmware Upgrade Manual for v1.3.0 This manual introduces Firmware upgrade and TTS data upgrade. The firmware upgrade is necessary. The TTS data upgrade is not necessary if the version
More informationDPM-3221 Digital DC Power Meter with data logging capability.
Introduction DPM-3221 Digital DC Power Meter with data logging capability. User Manual As a digital DC power meter, it measures the real time DC Voltage (5-60V), DC Current (0-200 A with the correct shunt),
More informationGPIB-232CT-A IBCL EPROM Installation Guide
NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.
More informationFirmware zippack name : R exe Firmware File Name : Dell1815dn_V _AutoUpgrade.exe
Updating Firmware on the Dell Laser Printer MFP 1815dn NOTICE: Do not turn off your printer or computer, or disconnect any cables during this operation. Doing this will corrupt the memory and the printer
More informationPMEUCM Hardware. Niobrara Research & Development Corporation P.O. Box 3418 Joplin, MO USA
PMEUCM Hardware Manual PMEUCM Hardware Installation Manual This manual covers the PMEUCM hardware features and installation procedures. Effective: August 10, 2017 Niobrara Research & Development Corporation
More informationitrax PC Replacement Quick Start Guide P/N Pre-Software Installation
Quick Start Guide P/N 60789-0 Use this procedure to upload the current software onto a new itrax PC. To access the newest software, contact ICS Technical Support at ics.tech.support@nordson.com. Follow
More informationQuick Start Guide Demo Distance2Go. July 2018
Quick Start Guide Demo Distance2Go July 2018 Table of Contents 1 Hardware Description 2 Tools Installation 3 Demo Distance2Go USB Connections 4 Building, Flashing and Debugging 5 Raw data streaming 2 Table
More informationFirmware, Database, & PC Application Update Installation Instructions
Firmware, Database, & PC Application Update Installation Instructions IMPORTANT Please read before you begin the installation. To avoid possible errors, it is recommended to install the updates as described
More informationUpdating X30/ Bridge Software
Updating X30/ Bridge Software Bourgault Industries Ltd has released new software for the X30 and the Bridge, follow the instructions below. Please go to our download site at download.bourgault.com. Enter
More informationDPM Digital DC Power Meter with Data logging capability. User Manual
DPM-3232 Digital DC Power Meter with Data logging capability User Manual Introduction As a digital DC power meter, it measures the real time DC Voltage (5-60V), DC Current (0-60A), Watt, and it also displays
More informationVP- X Pro & VP- X Sport
VP- X Configurator Release Notes As of version 1.6 (May 13, 2013) This document updated October 31, 2013 Contents 1. Models...1 2. Updating the VP-X Pro and Sport firmware (Automatic)...1 3. Software Upgrade
More informationGIE 8051 Mini Kit. User Manual
GIE 8051 Mini Kit User Manual www.gie.com.my Page 1 of 8 Content Features...3 Function Block...3 Development Setup...4 Jumper selection...4 Required Software...5 Install PL-2303 Driver (USB to Serial port)...5
More informationOCTOPROG User Manual Ver 103
Research & Development Facility 41/1854, Veekshanam Road, Near Kacheripady, Ernakulam North, Cochin -18 PH:-0484 4014004 www.neonainnovation.com OCTOPROG User Manual Ver 103 Contents CHAPTER 1 Introduction..2
More informationSidewinder Development Board rev 1.0
33 Sidewinder Development Board rev 1.0 Features Altera MAX V CPLD 5M160ZT100C5 JTAG programmable USB programmable USB powered 12 On board LEDs 10 on board switches 3 RGB LEDs One 40 pin expansion headers
More informationMechanical specifications Dimensions (L x W x H) 290 x 125 x mm Weight 445 g. Female DC Barrel Jack Socket 5.5x2.1 mm
Mirror Driver v1.0 The Mirror Driver v1.0 consists of two main hardware blocks. The first acts as a Data Acquisition (DAQ) board while the second is an FPGA evaluation kit which is used as a Digital Signal
More informationX5105 Firmware Update. Instruction
X5105 Firmware Update Instruction Things to prepare for updating the firmware: 1. USB-to-Serial cable 2. X5105 3. A computer running windows(xp/vista/7/8/10) operating system 4. A 12~15VDC(current ability
More informationReflow Controller NSB006 GUI User Manual Version 1.00
Reflow Controller NSB006 GUI User Manual Version 1.00 Page 1 of 14 Document History Version Modified By Date Comments 1.00 N Barnes 2017-01-14 Initial release TABLE OF CONTENTS 1 Introduction... 3 1.1
More informationLongshine Technologie Europe GmbH LCS-MFP101-2 Multifunction Printserver
Longshine Technologie Europe GmbH LCS-MFP101-2 Multifunction Printserver www.longshine.de TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3
More informationPRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory.
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory. 1.0 Objectives In this lab you will get familiar with the concept of using the
More informationUser Guide Feb 5, 2013
HI 8435 32 Sensor Array with Ground/Open or Supply/Open Sensors and SPI interface. Evaluation Board 23351 Madero, Mission Viejo, CA 92691. USA. Tel: + 1 949 859 8800 Fax: + 1 949 859 9643 Email: sales@holtic.com
More informationCC186 AND CC186/2 STAND-ALONE OR SYSTEM CLOCK
FN:CC186M2.DOC CC186 AND CC186/2 STAND-ALONE OR SYSTEM CLOCK DESCRIPTION The CC186 is a single sided clock with six, 1.8 inch high digits. The CC186/2 is a double sided clock with six, 1.8 inch high digits
More informationTEMPO ATA133. Macintosh PCI Host Adapter Card. Quick Start Guide for Tempo ATA133
TEMPO ATA133 Macintosh PCI Host Adapter Card Quick Start Guide for Tempo ATA133 You Should Have The following items should be included in your product package: One Tempo ATA133 Macintosh PCI Host Adapter
More informationPI Scanner User Guide
PI Scanner User Guide Table of Contents 1. Highlights 2. Overview 3. Installation 3.1. PI Scanner Software Installation 3.2. USB to Serial Interface Board Installation 3.3. Programming the PI Scanner IP
More informationINSTALLING THE PS3 XBOX READY SOFTWARE:
INSTALLING THE PS3 XBOX READY SOFTWARE: 1. Insert the Installation CD to CD-ROM drive and execute Ready_Setup.exe NOTE: If it is the first time for the target USB disk using under this software, the software
More informationInstalling USB Drivers to Windows System
1/9 Installing USB Drivers to Windows System Noptel Oy, Oulu Finland 1.3.2010 Noptel s USB devices uses USB/Serial Converters made by FTDI Ltd. The drivers for the USB Converter are provided by FTDI (http://www.ftdichip.com/).
More informationInstructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set
Instructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set Updates to the instrument firmware are available from the Applied Instruments website. Requirements
More informationLV8548MCSLDGEVB. Stepper Motor Driver Module Solution Kit Quick Start Guide
LV8548MCSLDGEVB Stepper Motor Driver Module Solution Kit Quick Start Guide Overview The LV8548MCSLDGEVB is an ON Semiconductor motor driver module featuring the LV8548MC. This module is capable of easily
More informationILC LightLEEDer MicroLite 1000P Retrofit Installation
ILC LightLEEDer MicroLite 1000P Retrofit Installation Congratulations on the purchase of your new ILC LightLEEDer Retrofit System. The ILC LightLEEDer MicroLite Retrofit System is designed for the replacement
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationXM360 X-Tractor Troubleshooting
XM360 X-Tractor Troubleshooting 1. Downloading X-Tractor PROBLEM: You encounter an error during the downloading process. ANSWER: Stop the download process and retry. If you continue to experience difficulties,
More informationAdaptec AUA Multi-Card Media Reader. Installation Guide
R Adaptec AUA-7500 Multi-Card Media Reader Installation Guide In this Booklet... Kit Contents 2 This Is Your Adaptec Media Reader 3 Installing Your Adaptec Media Reader 4 Installing the Device Drivers
More informationFirmware, Database, & PC Application Update Installation Instructions
Firmware, Database, & PC Application Update Installation Instructions IMPORTANT Please read before you begin the installation. To avoid possible errors, it is recommended to install the updates as described
More informationNX-588E USB Flash Programmer Instructions v1.1
NX-588E USB Flash Programmer Instructions v1.1 Installing the NX-588E on a computer This process should take 5-10 min. 6. The following screen will appear: It is essential you carry out this step from
More informationKNJN I2C bus development boards
KNJN I2C bus development boards 2005, 2006, 2007, 2008 KNJN LLC http://www.knjn.com/ Document last revision on December 5, 2008 R22 KNJN I2C bus development boards Page 1 Table of Contents 1 The I2C bus...4
More informationAddendum for Tempo HD (Without Drive)
Addendum for Tempo HD (Without Drive) You Should Have (Part Number THD-M) In addition to the parts listed on the Tempo HD quick start guide, the following items should be included in your product package:
More informationUser Manual Firmware Update
Firmware Update derfusb-23e00 derfusb-23e00 JTAG derfusb-23e06 derfusb-23e06 JTAG derfusb-13e00 derfusb-13e00 JTAG derfusb-13e06 derfusb-13e06 JTAG Document Version V01.01 2011-07-01 Table of contents
More informationFirmware Upgrade for JVC projectors 2013 models (Important Pre Update Information)
Firmware Upgrade for JVC projectors 2013 models (Important Pre Update Information) Before any firmware updates can be implemented, please make sure that you have a connection to the JVC projector from
More informationTherefore, before you can use the Microlog Inspector application for the first time, you must perform the following steps:
SKF Microlog Inspector Setup Guide Microlog Inspector setup overview The new Microlog Inspector application uses a different, much easier communication method than previous MARLIN versions. With the new
More informationGrayhill 3D70 Series 7 Inch Display. Development Kit Hardware Setup Instructions
Grayhill 3D70 Series 7 Inch Display Development Kit Hardware Setup Instructions Revision History Revision Date Description A 11/11/2016 Original Release Introduction These instructions describe how to
More informationEMT1250 LABORATORY EXPERIMENT. EXPERIMENT # 7: VHDL and DE2 Board. Name: Date:
EXPERIMENT # 7: VHDL and DE2 Board Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Learn how to create and modify
More informationFPGA Introductory Tutorial: Part 1
FPGA Introductory Tutorial: Part 1 This tutorial is designed to assist in learning the basics of the Altera Quartus II v9.0 software. Part 1 of the tutorial will cover the basics of creating a Project,
More informationAxiom Device Firmware Updater Device Firmware Update Tool for the Axiom F6, H1, and H2 Dataloggers
EXTREME ENVIRONMENTS. EXTREMELY RELIABLE. Axiom Device Firmware Updater Device Firmware Update Tool for the Axiom F6, H1, and H2 Dataloggers 700-Firmware Updater Rev 6 14 Nov 2017 User Manual Download,
More informationAllen-Bradley Motors
Installation Instructions Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers Purpose Firmware Update Kit Contents Hardware and Software Requirements This
More informationINSTRUCTIONS TO UPDATE FIRMWARE FOR
INSTRUCTIONS TO UPDATE FIRMWARE FOR Dranetz 1000 New Durham Road, Edison, New Jersey 08818 Telephone 1-800-372-6832 or 732-287-3680 Fax 732-248-1834 www.dranetz.com Updating the HDPQ SP s Firmware The
More informationThis tutorial was written by Team Xecuter. If you use anything from this tutorial please give credits and also a direct link to this page. Also if we have made any mistakes or left anything out please
More informationUser Guide for Running a Project on the Embest Board
1. Overview User Guide for Running a Project on the Embest Board Li Yu, M. Serra, S. Lee-Cultura Department of Computer Science, University of Victoria The Embest University board is a development board
More information1. Introduction P Package Contents 1.
1 Contents 1. Introduction ------------------------------------------------------------------------------- P. 3-5 1.1 Package Contents 1.2 Tablet Overview 2. Using the Tablet for the first time ---------------------------------------------------
More information