ULTIMATE CART FIRMWARE UPGRADE GUIDE
|
|
|
- Emery Richardson
- 5 years ago
- Views:
Transcription
1 Page 1 ULTIMATE CART FIRMWARE UPGRADE GUIDE This guide is intended as a reference to help understand the firmware upgrade process for the Ultimate Cart and highlight potential issues. It is not a comprehensive step by step guide covering every possible detail. The guide provides some background information, gives some recommendations, and shows what to expect for those considering attempting the upgrade themselves. The guide focuses on installation using a 64 bit windows PC. REQUIRED HARDWARE To update the Ultimate Cart firmware you will need a JTAG programmer, a 5V power supply to use while programming, and PC. These instructions assume an Altera USB Blaster clone will be used. An authentic USB Blaster from Altera costs about $300 USD. Clones on ebay or amazon run $5-$20 USD, but not all of the clones are created equal. Here is one from ebay: And another from Amazon: Some research may be necessary to ensure you purchase your USB Blaster from a source that was known to work for others. However, this will not guarantee the USB Blaster you get will operate properly if the seller changes their supplier or had mixed stock. Both of these worked with Windows 8.1, 64-bit Quartus 15.1 programmer. I was unable to get these to work using Lubuntu Linux with the 14.1 or 15.1 programmer. Don t plug the USB Blaster into the PC until after the programmer and tools software has been installed. External power must be supplied to the Ultimate Cart during programming. Using a 5V battery operated power supply with an on/off switch is highly recommended. The ground/common side of a battery operated supply will adjust to match the voltage level of your computer USB port. Using a 5V power supply that plugs into the wall might cause the ground/common voltage levels to be unequal. This could result in an undesirable number of electrons flowing into or out of the USB port on the computer at a rate causing damage to any of the devices involved. The external 5V supply is connected to the external power jack on the back of the board. Not all of the Ultimate Cart sellers populated the power connectors due to concerns over short circuits. A JST-XH jack and connector would work if you don t have anything else on hand. The plastic housing shroud on the jack will obscure the the silkscreen labels on the PCB. Wires could be temporarily soldered to the board as well. An on/off switch is
2 Page 2 recommended so all the connections can be made prior to turning on the power supply. External power can also be supplied by an Atari, if the PC and Atari are close enough or can be relocated. SOFTWARE Download the programmer and tools software from the Altera website: is recommended for the XEX firmware. If you want to flash the original firmware on windows, programmer revision 14.1 is recommended. The option for a direct download saves the hassle of installing their download manager plugin. The Quartus prime software complete package is a several gigabyte download and takes even more space to install. The windows programmer and tools is still about 350 MB. Save the installer to a convenient directory. Download the desired firmware for the Ultimate Cart and save to this directory. The file that ultimately contains the firmware to download will end with a.pof extension. Two versions of the processor have been used to fabricate the Ultimate Cart, 10M08SAE144C8G and 10M08SAE144C8GES. Early boards used an Engineering Sample device; its part number ends in ES. Subsequent boards used the production version of the processor. When new.pof files are compiled from the source code, the generated output file will be specific for the production or ES processor. Download the correct file based on the part marking for the processor used to make your Ultimate Cart. Released versions of the firmware are best downloaded from the Github repository. Beta versions have been posted to the relevant AtariAge forum posts. When downloading from Github find the desired.pof file in the Programming Files directory and then choose the option in your web browser to Save Link As or equivalent. Files/
3 Page 3 Run the installer for the Altera programmer and tools. There are no special options to select until the end. After installation is complete, drivers for the USB Blaster need to be installed. Let the installer launch the driver installation wizard. The others don t need to be launched at this time. Click through the wizard to install the USB Blaster drivers.
4 Page 4 Now the USB Blaster can be connected to the PC USB port. Windows has another progress bar while the device is installed. Remember what USB port you connect the device. Always using the same USB port might help to avoid fighting with the drivers in the future.
5 Page 5 Now is a good time to open up the windows device manager to see if the USB Blaster is recognized and driver properly installed. Neither the ebay or amazon USB Blaster had the drivers work right from the start. Both have the same hardware Ids even though the Device Descriptions are different. Ebay Amazon The goal is to get the USB Blaster drivers installed properly for the hardware (no yellow explanation warning). Once it is installed properly, you can proceed to starting the programmer to flash the firmware. Right click on the USB Blaster in the device manager and pick Update Driver Software
6 Page 6 Select the options to pick from list of device drivers on my computer And select JTAG cables Select the option for the model for the USB Blaster (JTAG interface) and acknowledge the warning. Hopefully, this is successful:
7 Page 7 The Altera literature for installing the USB Blaster drivers is available here. It might help troubleshoot any issues encountered. Steps should be pretty similar for other versions of windows. FLASHING THE FIRMWARE Open the Quartus Prime Programmer. The installer adds a shortcut to the Windows start menu. This is the default location the application is installed: This opens the main programmer application window.
8 Page 8 Next the hardware needs to be selected. Click the Hardware Setup button in the upper left. The following dialog box opens:
9 Page 9 Select USB Blaster from the drop down selection box and close the dialog box. In the main window select the Add File button from the left hand side and select the.pof file. The file will be displayed in the programmer window. Select the indicated check boxes to Program/Configure and Verify. Remove the SD card from the Ultimate Cart, and connect the USB Blaster 10 pin ribbon cable to the Ultimate Cart programming header (and the USB Blaster). The shroud is keyed so it only fits on in one direction. Finally, connect the 5V power supply to the Ultimate Cart (double check it is not hooked up reversed), and turn the power supply on if necessary. Everything is now setup, select the Start button to perform the programming. The progress bar in the upper right hand corner with indicate when the programming has been completed. Programming takes about 10 to 30 seconds. I noticed one of the programmers was a bit faster. Review the message log for any errors once complete.
10 Page 10 To disconnect the Ultimate Cart, first turn off and remove the 5V supply. Then unplug the USB cable from the PC and finally disconnect the 10 pin programming cable. The programmer software can be closed. No need to save the configuration file on the PC. If everything updated okay, replace the SD card and test it in the Atari.
1. Install Programmer Software
Notes: Uses IST-12242-001A Programming Pod and 12-position 1 mm flat flex cable. If you encounter any problems while trying to program your unit, please contact Rebecca Afzal via email or call 419-536-5741
HPSDRProgrammer_v2 v2.0. Apache 10/100/100D
HPSDRProgrammer_v2 v2.0 Quartus-II Programmer ByteBlaster instructions for Apache 10/100/100D 1 of 11 Table of Contents Loading FPGA code with HPSDRProgrammer_v2 v2.0...3 Installing OpenHPSDR's K0VS HPSDRProgrammer_V2:...3
Sidewinder Development Board rev 1.0
33 Sidewinder Development Board rev 1.0 Features Altera MAX V CPLD 5M160ZT100C5 JTAG programmable USB programmable USB powered 12 On board LEDs 10 on board switches 3 RGB LEDs One 40 pin expansion headers
EARTH PEOPLE TECHNOLOGY. ODIN-LINK BLE + MAXPROLOGIC Development System User Manual
EARTH PEOPLE TECHNOLOGY ODIN-LINK BLE + MAXPROLOGIC Development System User Manual This User Manual covers the Odin-Link and MaxProLogic Development System. The Odin-Link board includes the Texas Instruments
NOTE: This tutorial contains many large illustrations. Page breaks have been added to keep images on the same page as the step that they represent.
CSE 352 Tutorial # 4 Synthesizing onto an FPGA Objectives This tutorial will walk you through the steps of implementing a design made in Active-HDL onto the Altera Cyclone II FPGA NOTE: This tutorial contains
CSE P567 - Winter 2010 Lab 1 Introduction to FGPA CAD Tools
CSE P567 - Winter 2010 Lab 1 Introduction to FGPA CAD Tools This is a tutorial introduction to the process of designing circuits using a set of modern design tools. While the tools we will be using (Altera
Cygnos360 V2 Installation Manual
VERSION 1.03 - JANUARY, 2010 www.cygnos360.com Contents:... 1 1. What you need... 2 1.1. Tools... 2 2. Preparation... 3 2.1. Preparing the solder points... 3 3. Installing in your Xbox360... 4 3.1. Installing
FPGA RGB Matrix. Created by lady ada. Last updated on :15:42 PM UTC
FPGA RGB Matrix Created by lady ada Last updated on 2017-12-27 09:15:42 PM UTC Guide Contents Guide Contents Overview Controlling the Adafruit 32x16 RGB LED Matrix with a DE0-Nano FPGA Board Prerequisites
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory.
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory. 1.0 Objectives In this lab you will get familiar with the concept of using the
EE 231 Fall Lab 1: Introduction to Verilog HDL and Altera IDE
Lab 1: Introduction to Verilog HDL and Altera IDE Introduction In this lab you will design simple circuits by programming the Field-Programmable Gate Array (FPGA). At the end of the lab you should be able
OpenSprinkler v2.2u Build Instructions
OpenSprinkler v2.2u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
Simple Instructions for 808 HD Car Key Micro Camera (#16)
808 #16 Manual R2 1 of 6 Simple Instructions for 808 HD Car Key Micro Camera (#16) Thank you for your purchase of our 808 Car Key Micro-camera (#16). If this is the first time you are using a product of
ootbrobotics.com Electronics and Robotics LLC
2 Overview... 3 Device Connections... 3 Installing Drivers... 4 Installing FTDI Drivers... 4 Installing Quartus Drivers... 4 Using the Programmer... 5 Opening the Quartus Programmer Window... 5 Special
Cygnos360 V2 Installation Manual
Cygnos360 V2 Installation Manual VERSION 1.04. - MARCH, 2010 www.cygnos360.com Contents: Cygnos360 V2 Installation Manual... 1 1. What you need... 2 1.1. Tools... 2 2. Preparation... 3 2.1. Preparing the
The University of Toledo EECS:6660:0xxField Programmable Gate Arrays s09l1.fm - 1 Dr. A.D. Johnson
EECS:6660:0xxField Programmable Gate Arrays s09l1.fm - 1 Lab Assignment #1 Due: Friday, February 27 2009 Introduction to Altera Quartus II Environment using VHDL Entry 1. Objectives - introduction to Quartus
University of Florida EEL 3701 Dr. Eric M. Schwartz Madison Emas, TA Department of Electrical & Computer Engineering Revision 1 5-Jun-17
Page 1/14 Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate and two inverters under the Quartus environment. Upon completion
Longshine Technologie Europe GmbH
Longshine Technologie Europe GmbH www.longshine.de TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3 2. MFP SERVER INSTALLATION...5
PC Focus Control Operator's Guide
PC Focus Control Operator's Guide Copyright 2008 JMI Telescopes Jim's Mobile, Incorporated 8550 West 14th Avenue Lakewood, CO 80215 U.S.A. Phone (303) 233-5353 Fax (303) 233-5359 Order Line (800) 247-0304
PROFESSIONAL. Users Guide. Version 3.5
PROFESSIONAL Users Guide Version 3.5 Table of Contents 1 System Overview... 3 2 System Requirements... 3 3 Contents in ECMTUNE System Box... 3 4 Installation Information... 4 5 Registration Information...
DOWNLOADING DESIGNS TO THE ALTERA DE10-LITE FPGA
DOWNLOADING DESIGNS TO THE ALTERA DE10-LITE FPGA Consider the design of a three-bit prime number detector completed in the MSOE schematic entry tutorial. Figure 1 shows the block diagram and truth table.
OpenSprinkler v2.1u Build Instructions
OpenSprinkler v2.1u Build Instructions (Note: all images below are 'clickable', in order for you to see the full-resolution details. ) Part 0: Parts Check Part 1: Soldering Part 2: Testing Part 3: Enclosure
Terasic DE0 Field Programmable Gate Array (FPGA) Development Board
Lecture FPGA-01 DE0 FPGA Development Board and Quartus II 9.1 FPGA Design Software Terasic DE0 Field Programmable Gate Array (FPGA) Development Board 1 May 16, 2013 3 Layout and Components of DE0 May 16,
CHAPTER 1 Introduction of the tnano Board CHAPTER 2 tnano Board Architecture CHAPTER 3 Using the tnano Board... 8
CONTENTS CHAPTER 1 Introduction of the tnano Board... 2 1.1 Features...2 1.2 About the KIT...4 1.3 Getting Help...4 CHAPTER 2 tnano Board Architecture... 5 2.1 Layout and Components...5 2.2 Block Diagram
Simple Instructions for 808 HD Car Key Micro Camera (#16)
Simple Instructions for 808 HD Car Key Micro Camera (#16) Thank you for your purchase of our 808 Car Key Micro-camera (#16). If this is the first time you are using a product of this kind, please follow
MEGATRONICS V3.0 QUICK START GUIDE
MEGATRONICS V3.0 QUICK START GUIDE Thank you for purchasing the Megatronics v3.0! This small guide will answer the basic questions on how to connect the board to your 3D printer. For more information visit
Chapter 2 Getting Hands on Altera Quartus II Software
Chapter 2 Getting Hands on Altera Quartus II Software Contents 2.1 Installation of Software... 20 2.2 Setting Up of License... 21 2.3 Creation of First Embedded System Project... 22 2.4 Project Building
EXPRESS. Users Guide. Version 3.5
EXPRESS Users Guide Version 3.5 Table of Contents 1 System Overview... 3 2 System Requirements... 3 3 Contents in ECMTUNE System Box... 3 4 Installation Information... 4 5 Registration Information... 7
TABLE OF CONTENTS COPYRIGHT INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION
TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3 2. MFP SERVER INSTALLATION...5 PREPARATION...5 CONFIGURATION SOLUTION TABLE...5
Cygnos360 V2 Installation Manual
VERSION 1.0. - OKTOBER, 2009 www.cygnos360.com Contents: 1. What you need...2 1.1. Tools...2 2. Preparation...3 2.1. Preparing the solder points...3 3. Installing in your Xbox360...4 3.1. Installing the
Intel FPGA USB Download Cable User Guide
Intel FPGA USB Download Cable User Guide Subscribe Latest document on the web: PDF HTML Contents Contents 1. Introduction to Intel FPGA Download Cable...3 1.1. Intel FPGA Download Cable Revision... 3 1.2.
HOW TO USE ESP8266 WITH ARDUINO IDE
HOW TO USE ESP8266 WITH ARDUINO IDE This document applies for the following products: ESP8266-EVB; ESP8266-EVB-BAT; ESP8266-EVB-BAT-BOX Document revision B, February 2017 All boards produced by Olimex
CPE 200L LABORATORY 4: INTRODUCTION TO DE2 BOARD UNIVERSITY OF NEVADA, LAS VEGAS GOALS: BACKGROUND:
CPE 200L LABORATORY 4: INTRODUCTION TO DE2 BOARD DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS GOALS: Getting familiar with DE2 board installation, properties, usage.
Longshine Technologie Europe GmbH LCS-MFP101-2 Multifunction Printserver
Longshine Technologie Europe GmbH LCS-MFP101-2 Multifunction Printserver www.longshine.de TABLE OF CONTENTS COPYRIGHT...2 1. INTRODUCTION...3 PRODUCT OVERVIEW...3 COMPONENTS AND FEATURES...3 HARDWARE INSTALLATION...3
WVL2 Wireless Vehicle Link 2 Installation and Setup Manual
WVL2 Wireless Vehicle Link 2 Installation and Setup Manual Chapter 1: Introducing the Wireless Vehicle Link 2...1 WVL2 Components...2 Component Checklist...3 Product Specifications...4 System Requirements...5
Getting Started with STK200 Dragon
Getting Started with STK200 Dragon Introduction This guide is designed to get you up and running with main software and hardware. As you work through it, there could be lots of details you do not understand,
Intel FPGA USB Download Cable User Guide
Intel FPGA USB Download Cable User Guide UG-USB81204 2016.10.31 Subscribe Send Feedback Contents Contents 1 Introduction to USB Download Cable... 3 1.1 USB Download Cable Revision... 3 1.2 Supported Devices
Startfish driver installation is a two step process for Windows operating systems.
Installation Windows Minimum System Requirements Windows XP (Service Pack 1) Intel Pentium III or equivalent processor 128MB of ram USB 2.0 Port (The camera will not work on a standard USB 1.1 port) Startfish
OBDI RT Tuner Quick Start Guide
OBDI RT Tuner Quick Start Guide Revision A Page 1 Table of Contents Introduction...3 Minimum PC Requirements...3 Program Installation...3 Registering the Program...4 Select the Desired ECM Definition Files...6
XM360 X-Tractor Troubleshooting
XM360 X-Tractor Troubleshooting 1. Downloading X-Tractor PROBLEM: You encounter an error during the downloading process. ANSWER: Stop the download process and retry. If you continue to experience difficulties,
University of Florida EEL 3701 Dr. Eric M. Schwartz Department of Electrical & Computer Engineering Revision 0 12-Jun-16
Page 1/14 Quartus Tutorial with Basic Graphical Gate Entry and Simulation Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate
Grelllbbb s ESP Flashamater Adaptimizer Assembly & User Guide
Grelllbbb s ESP Flashamater Adaptimizer Assembly & User Guide Overview The GEFA (we don t understand Grelllbb any better than you do, so we ll just abbreviate it GEFA) is a small programming tool that
EMUL-PPC-PC. Getting Started Guide. Version 1.0
EMUL-PPC-PC Getting Started Guide Version 1.0 EMUL PowerPC Getting Started Guide Edition1 ICE Technology. All rights reserved worldwide. Contents Warranty Information European CE Requirements User Responsibility
EMT1250 LABORATORY EXPERIMENT. EXPERIMENT # 7: VHDL and DE2 Board. Name: Date:
EXPERIMENT # 7: VHDL and DE2 Board Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Learn how to create and modify
Installing LE History Record Reader program software.
INSTALLATION & OPERATING INSTRUCTIONS FOR THE LE HISTORY RECORD READER These Instructions will inform you on how to install software to use the RS-232/USB Isolator- Adapter and your LE History Record Reader
Figure 26 CC Debugger Interface
Figure 26 CC Debugger Interface Once the CC Debugger is set up with the status indicator LED showing green, you are ready to either read or write a hex file from the board, or to start debugging a project
FURIOUS TRUE-D DIVERSITY RECEIVER V3.6 Attitude
FURIOUS TRUE-D DIVERSITY RECEIVER V3.6 Attitude USER S MANUAL Please contact us if you need further assistance: Tech support: tech@furiousfpv.com Sales support: sales@furiousfpv.com Website: http://furiousfpv.com/
GH1/GH2/GH3 Dual Camera Controller Adapter User s Guide
GH1/GH2/GH3 Dual Camera Controller Adapter User s Guide Thank you for purchasing our controller product. The following information will help you successfully connect this controller board to your cameras
Name EGR 2131 Lab #6 Number Representation and Arithmetic Circuits
Name EGR 2131 Lab #6 Number Representation and Arithmetic Circuits Equipment and Components Quartus software and Altera DE2-115 board PART 1: Number Representation in Microsoft Calculator. First, let s
Shack Clock kit. U3S Rev 2 PCB 1. Introduction
Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used
BOOSTBYSMITH S ECU FLASHING INTERFACE (Gen II Hayabusa)
BOOSTBYSMITH S ECU FLASHING INTERFACE (Gen II Hayabusa) Contact Information: Greg Smith www.boostbysmith.com greg@boostbysmith.com (517)743-3666 INDEX I. Hardware Included II. III. IV. ECU1.0 Basics Installation
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II This lab manual presents an introduction to the Quartus II Computer Aided Design (CAD) system. This manual gives step-by-step
CSEE W4840 Embedded System Design Lab 1
CSEE W4840 Embedded System Design Lab 1 Stephen A. Edwards Due February 2, 2009 Abstract Learn to use the Altera Quartus development envrionment and the DE2 boards by implementing a small hardware design
HOW TO UPGRADE ESP8266 BOARDS USING ESP FLASH DOWNLOAD TOOLS
HOW TO UPGRADE ESP8266 BOARDS USING ESP FLASH DOWNLOAD TOOLS This document applies for the following products: ESP8266-EVB; ESP8266-EVB-BAT; ESP8266-EVB-BAT-BOX; MOD-ESP8266-WIFI-DEV; MOD-ESP8266-WIFI;
Samsung Moment Update Instructions Updated
Samsung Moment Update Instructions Updated 10.06.10 It is important that you follow these instructions to ensure your device is updated properly. Requirements for Performing Upgrade You will need the following
DEC RL01/RL02 DISK-DRIVE EMULATOR User Manuel for the DE10-Lite board
DEC RL01/RL02 DISK-DRIVE EMULATOR User Manuel for the DE10-Lite board DE10-Lite board with emulator interface Embedded environment based on the Altera MAX 10 FPGA. Emulates up to 4 RL01/RL02 drives simultaneously
Atola Disk Recycler Multi-port wiper and tester. User s Manual v1.1
Atola Disk Recycler Multi-port wiper and tester User s Manual v1.1 Thank you for purchasing an Atola Technology product The Atola Disk Recycler is a scriptable high-speed disk drive tester, wiper, repairer
ViCoN-Bot Tutorial. Users Guide Summer 2002 Version 1.0. Jeff Vickers Kwabena Bosompem Kevin Walker Andre Moore
ViCoN-Bot Tutorial Users Guide Summer 2002 Version 1.0 Jeff Vickers Kwabena Bosompem Kevin Walker Andre Moore Introduction This document gives instructions on how to make the ViCoN-Bot traverse a track
Single cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
CSEE W4840 Embedded System Design Lab 1
CSEE W4840 Embedded System Design Lab 1 Stephen A. Edwards Due February 3, 2011 Abstract Learn to use the Altera Quartus development envrionment and the DE2 boards by implementing a small hardware design
keyestudio Keyestudio MEGA 2560 R3 Board
Keyestudio MEGA 2560 R3 Board Introduction: Keyestudio Mega 2560 R3 is a microcontroller board based on the ATMEGA2560-16AU, fully compatible with ARDUINO MEGA 2560 REV3. It has 54 digital input/output
Application Note: AN0106. On-Board SPI Programming with Dediprog tools: End User Version
4F., No.7, Ln. 143, Xinming Rd., Neihu Dist., Taipei City 114, Taiwan Application Note: AN0106 On-Board SPI Programming with Dediprog tools: End User Version (This document is provided to help users who
Installing Komplete 5 with Direct Install
Installing Komplete 5 with Direct Install This document discusses how to use Receptor s Direct Install feature to install and update Komplete 5, its plugins, and its libraries. In order to install Komplete
AVR Development Board
AVR Development Board Campus Component Pvt. Ltd. DISCLAIMER Information furnished is believed to be accurate and reliable at the time of publication. However, Campus Component Pvt. Ltd. assumes no responsibility
EasyGX. GX Development Kit Guide. Ver: 1.0. Cytech Technology A Macnica Company
EasyGX GX Development Kit Guide Ver: 1.0 Cytech Technology A Macnica Company www.cytech.com 2013-04-25 Copyrights Copyright 2013 Cytech Technology Ltd. All Rights Reserved 1 Reversion History Updated
PCS-2. Universal Infrared Remote PC Power Switch
PCS-2 Universal Infrared Remote PC Power Switch General Description The PCS-2 allows you to switch your PC / HTPC on-off with your existing TV or universal infrared (IR) remote. Single button mode allows
AFEDRI SDR 192kHz firmware upgrade process description.
AFEDRI SDR 192kHz firmware upgrade process description. 1. Attention!!! Please run SDR Control software before firmware upgrade process beginning. Switch to tab About and write value of Front End Main
Configuration and programming minimodules MMfpga01 and MMfpga11
MMfpga01 MMfpga11 Configuration and programming minimodules MMfpga01 and MMfpga11 1 Index 1. Instalation of the QUARTUS II Web Edition...3 2. How to install QUARTUS II Web Edition...5 3. Installation of
For Quartus II Software. This Quick Start Guide will show you how to set up a Quartus
Quick Start Guide For Quartus II Software This Quick Start Guide will show you how to set up a Quartus II project, enter timing requirements, and compile the design into an Altera device. 1 Three-Step
IMPLEMENTING COUNTERS
EECS:6660:0xxField Programmable Gate Arrays s11l1_fpga.fm - 1 Lab Assignment #1 Due Thursday, March 31 2011 IMPLEMENTING COUNTERS 1. OBJECTIVES - learning the VHDL implementation process using Language
TB Touchscreen software update Revision 1.5, with upgraded PCB Revision 2.2 (P/N K) Topic: JET6, OVERVIEW UPDATE
Topic: JET6, Touchscreen software update Revision 1.5, with upgraded PCB Revision 2.2 (P/N1600202K) TB No.: 10046 Date: Aug2017 Affected Machines: JET6 Priority: Medium Created By: Gareth Fitzpatrick From
Non-Volatile Configuration Scheme for the Stratix II EP2S60 DSP Development Board
Non-Volatile Configuration Scheme for the Stratix II EP2S60 DSP Development Board Qian Liu and S.W. Ellingson October 21, 2008 The Stratix II DSP development board (DSP board) has provided a non-volatile
Cambium Wireless Manager
Cambium Wireless Manager Client Setup Guide System Release 4.2 and Later Issue 1 November 2014 2014 Cambium Networks. All Rights Reserved. Accuracy While reasonable efforts have been made to assure the
Pulsed Frequency TM. Joint PEMFBasic Software Download, Installation and User Guide
Pulsed Frequency TM Joint PEMFBasic Software Download, Installation and User Guide Contents Account Registration... 3 Create an Account... 4 Download the Software... 6 Chrome... 7 Edge... 8 Firefox...
Lab 2: Introduction to Verilog HDL and Quartus
Lab 2: Introduction to Verilog HDL and Quartus September 16, 2008 In the previous lab you designed simple circuits using discrete chips. In this lab you will do the same but by programming the CPLD. At
PCB-STM32-F3U. Development baseboard for the STMicro Discovery-F3 module (STMicro part# STM32F3DISCOVERY)
PCB-STM32-F3U Development baseboard for the STMicro Discovery-F3 module (STMicro part# STM32F3DISCOVERY) Part Number: PCB-STM32-F3U (unpopulated PCB with Discovery module sockets, no other parts) STM32-F3U
ARDUINO MEGA 2560 REV3 Code: A000067
ARDUINO MEGA 2560 REV3 Code: A000067 The MEGA 2560 is designed for more complex projects. With 54 digital I/O pins, 16 analog inputs and a larger space for your sketch it is the recommended board for 3D
Scratch 2.0 Wireless Programming Guide for Vortex
Scratch 2.0 Wireless Programming Guide for Vortex DF4Scratch Service Vortex is a programmable robot developed by DFRobot. Based on the Arduino developing platform, Vortex is equipped with Atmega328 Arduino
Executive summary. Gather up the materials & tools required. Set up the BT2S for the ProChrono baud rate:
Executive summary On/Off switch A fully self-contained Bluetooth-to-ProChrono interface powered by three AA batteries Steady LED indicates Bluetooth connection Jack connects to ProChrono 1. Gather up the
Tutorial on Quartus II Introduction Using Verilog Code
Tutorial on Quartus II Introduction Using Verilog Code (Version 15) 1 Introduction This tutorial presents an introduction to the Quartus II CAD system. It gives a general overview of a typical CAD flow
1.0 Unpacking DALI KATCH Buttons and Connections Sound Mode
DALI KATCH MANUAL CONTENTS 1.0 Unpacking... 3 2.0 DALI KATCH Buttons and Connections... 4 2.1 DALI KATCH Button Overview...4 2.2 DALI KATCH Connector Overview...5 3.0 Power On/Off................ 6 3.1
EE 231 Fall EE 231 Lab 2
EE 231 Lab 2 Introduction to Verilog HDL and Quartus In the previous lab you designed simple circuits using discrete chips. In this lab you will do the same but by programming the CPLD. At the end of the
Neehr Perfect Guide: Installing the Citrix Plugin
Neehr Perfect Guide: Installing the Citrix Plugin Overview This guide covers how to install the Citrix plugin. The first time you log in to Neehr Perfect on any computer, you will be prompted to install
CSEE W4840 Embedded System Design Lab 1
CSEE W4840 Embedded System Design Lab 1 Stephen A. Edwards Due January 31, 2008 Abstract Learn to use the Altera Quartus development envrionment and the DE2 boards by implementing a small hardware design
Firmware, Database, & PC Application Update Installation Instructions
Firmware, Database, & PC Application Update Installation Instructions IMPORTANT Please read before you begin the installation. To avoid possible errors, it is recommended to install the updates as described
Typical applications where a CPLD may be the best design approach:
By: Carlos Barberis, dba Bartek Technologies Description of Bartek s CPLD1 development board. For some of us CPLD s are familiar devices and for others just another acronym in the electronic device industry.
USB BitJetLite Download Cable
USB BitJetLite Download Cable User Guide, Inc. (USA) 14100 Murphy Avenue San Martin, CA 95046 (408) 852-0067 http://www.slscorp.com Product Version: 1.0 Document Version: 1.0 Document Date: Copyright 2010,.All
TMC3in1 Torch & Motion Controller 3in1. Vol. 04: FAQ and Troubleshooting Guide
TMC3in1 Torch & Motion Controller 3in1 Plasma THC - 5 Axis Breakout Board Spindle Controller Vol. 04: FAQ and Troubleshooting Guide For use with TMC3in1 Plugin Rev: 4.2.x.x Author: Randall L Ray Very Sr.
Sonatype CLM - IDE User Guide. Sonatype CLM - IDE User Guide
Sonatype CLM - IDE User Guide i Sonatype CLM - IDE User Guide Sonatype CLM - IDE User Guide ii Contents 1 Introduction 1 2 Installing Sonatype CLM for Eclipse 2 3 Configuring Sonatype CLM for Eclipse 5
Light & Sound Control Module
Light & Sound Control Module Operation and Installation Manual G-Scale Graphics 5860 Crooked Stick Dr. Windsor, CO 80550 970-581-3567 GScaleGraphics@comcast.net www.gscalegraphics.net Revision 55: C: Updated
Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012
Phi-panel backpack assembly and keypad options Dr. John Liu 12/16/2012 1. Introduction:... 3 Currently available:... 3 2. Backpack assembly... 4 3. Connecting to a keypad... 6 4. Rotary encoder keypads...
linkzone User ManUal
LINKZONE User Manual Getting to Know Your Mobile Hotspot Power key WPS key LED indicator USB jack LED Description Part Power key WPS key LED indicators Charging / USB Port Reset Reboot Description Hold
Zero2Go. User Manual (revision 1.03) Wide Input Range Power Supply for Your Raspberry Pi. Copyright 2017 UUGear s.r.o. All rights reserved.
Zero2Go Wide Input Range Power Supply for Your Raspberry Pi User Manual (revision 1.03) Copyright 2017 UUGear s.r.o. All rights reserved. Table of Content Product Overview... 1 Product Details... 3 Package
How to Restore a chipkit Bootloader
This guide will show you how to restore your chipkit bootloader, in the event that it has been erased from a chipkit-compatible board. This operation is required if you have used MPLAB X to program the
Brookshire Software. Remote Advanced Playback Unit v3.2
Brookshire Software LLC Remote Advanced Playback Unit v3.2 FEATURES Motion and audio control MiniSSC, SMI, SV203, Parallax, Pololu, PicoPic, SSC32, K108A, DMX and compatible devices Digital 44.1kHz stereo
Renaming the Projector Adapter Advanced Settings Troubleshooting... 25
010-0730-00 Contents Contents... 2 Introduction... 4 Wireless Range... 4 System Requirements... 4 What's in the Box... 4 Adapter Status Indicators and Details... 5 What s the difference between Wireless
12v Power Controller Project Board
12v Power Controller Project Board 12 Volt Power Controller Introduction This board provides three functions... DC power gate Low voltage disconnect Voltage / current display The typical usage for this
The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.
Introduction 1 Welcome to the GENIE microcontroller system! The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.
Quartus II Version 14.0 Tutorial Created September 10, 2014; Last Updated January 9, 2017
Quartus II Version 14.0 Tutorial Created September 10, 2014; Last Updated January 9, 2017 This tutorial will walk you through the process of developing circuit designs within Quartus II, simulating with
This tutorial was written by Team Xecuter. If you use anything from this tutorial please give credits and also a direct link to this page. Also if we have made any mistakes or left anything out please
Creating a PCB Design with OrCAD PCB Editor
Creating a PCB Design with OrCAD PCB Editor This guide is focused on learning how to create a PCB (Printed Circuit board) design. The guide will make use of the PCB Flow menu that is part of this workshop