3M Projection Systems SCP Fixed & Folding Wall Mount Pre-Installation Packet

Transcription

1 3M Projection Systems SCP Fixed & Folding Wall Mount Pre-Installation Packet INDEX Pre-Installation Survey M Standard Installation... 7 Application Drawing... 9 Annotation Sensor Kit Required Tools Install Folding Wall Mount Install Fixed Wall Mount Install I/O Module Installation Check List Sample Installation Pictures M Projection Systems Department Tel: M 2009 All Rights Reserved Rev. A (3/2009) 1 of 38

2 3M Projection Systems Pre-Installation Survey Customer Name Title Company Address to: -or- Fax to: Phone Product to be installed Quantity Room Size Small <20 x 20 Medium >20 x 20 Large >40 x 40 Floor to Ceiling height Wall Type (Yes) (No) Minimum ½ thick Dry Wall Metal Interior studs Wood Plank or Plywood Masonry, plaster or poured concrete Brick or Cinder Block Metal Glass Mobile Cart Other Recessed Wall Installation Air Vent Vent Fan Sprinkler Heads 3M Projection Systems Department Tel: M 2008 All Rights Reserved B (11/2008) 2 of 38

3 3M Projection Systems Lighting (Yes) (No) Fluorescent Spot Lighting Standard bulbs Lighting within 3 feet of unit Lighting Controls Dimmer switch On/.Off switch Window Location Rear wall Front wall Side wall Power Outlet Within 3 feet of screen center -OR- 6 feet of expected projector position? 120VAC 20Amp Dedicated (grounded line) Computer Within 6 feet of unit? If not then location from unit in feet Type Model Mfg. # of VGA ports #of USB ports DVD Player Type Model Mfg. VCR Player Type Model Mfg. Video Conferencing System Type Model Mfg. Printer Type Model Mfg. Pre-Installation Survey 3M All Rights Reserved. 2 of 7 3 of 38

4 3M Projection Systems (Yes) (No) Pre-Installation Survey Audio System Type Model Mfg. A/V Controller Type Model Mfg. Other Type Model Mfg. Additional cables needed (Cables provided allow 2m (6 feet) of access if longer cables are needed then additional fees apply) Power Cord VGA DVI-I RS232 RCA Audio RCA Video S-Video Component Video USB 3.5mm mini stereo audio Special Cable routing required? Through Ceiling? Across Floor? Along Wall? Special A/V Outlet Location Type Special Equipment KVM switch Distribution Amplifiers Select Type: VGA S-Video Component Video 3M All Rights Reserved. 3 of 7 4 of 38

5 3M Projection Systems Other Electronic Devices in the room (Yes) (No) Watt saver (light controller) Door control Solid-state ballast controller Motion Detectors Remote IR controller Ultrasound device Other Annotation Devices Other If DMS or SCP product Whiteboard to be installed prior to this installation? Whiteboard to be installed as part of this task? (Note: additional fees apply) Existing chalkboard removed for additional fee Pre-Installation Survey Please provide a brief description below of the way you intend to use the product such as presentations with on screen annotation, training and conference presentations, video conferences with presentations and on screen annotation, etc. Please include description of other devices in the room and any multi-screen applications used. 3M All Rights Reserved. 4 of 7 5 of 38

6 3M Projection Systems Room Layout Drawing Example: Pre-Installation Survey Power Outlet 3M Unit Computer DVD Control Box (if applicable) Windows Table Lights Table Light Controls Table Table Door Chairs Please draw your room layout below including distances between equipment (photos may be sent via or additional pages may be attached when required) 3M All Rights Reserved. 5 of 7 6 of 38

7 3M Projection Systems 3M Standard Installation Pre-Installation Survey Basic installation service includes: Installation by authorized, licensed and insured professionals backed by 3M's best in the business satisfaction guarantee. Delivery of your new Projection equipment Delivery of additional mounting hardware required to fit with your building construction Installation to the existing construction code in your area Connect your new Projector to existing electrical outlets using standard cables Start up and test your new Projector to insure that it is working properly Provide guidelines for proper use of your new Projector Clean up the installation site Remove and dispose of packaging materials Includes User Training via teleconference, available at times scheduled by 3M during the month Information on available enhanced service plans to provide trouble free warranty coverage Locations beyond 30 miles from city center may incur additional fees Fixed Wall Mount installation includes: 3M Wall Mount Bracket if required for your site Assembly and installation of the Projector, Fixed Wall Mount and Wall Mount Bracket. Connect customer equipment & check out unit functionality. Folding Wall Mount installation includes: 3M Wall Mount Bracket if required for your site Assembly and installation of the Projector, Folding Wall Mount, Wall Mount Bracket & other 3M components & accessories. Connect customer equipment & check out unit functionality. Installation Available 5 Days a Week Service days and hours may vary by market. Pending completion of the site assessment; additional terms, fees and restrictions may apply. Some installations may require an on-site visit at additional cost to verify site conditions. On site training can be arranged at additional charge. Enhanced warranties are available at additional cost. NOTE: Installation and set up of additional equipment is available but not included. Please contact our Call Center at for additional quotation. Components installed are protected under their individual product warranties thus failures requiring their replacement may incur an additional fee. Some localities require seismic evaluation certification per applicable Engineering requirements. If this is required by the project engineer, program manager, site engineer, or architect then please contact us at for available evaluations defining the recommendations. 3M All Rights Reserved. 6 of 7 7 of 38

8 3M Projection Systems Pre-Installation Survey Warranty 3M warrants that when the 3M Product is used according to 3M s Intended Use Statement ( it will perform satisfactorily for the warranted durability period as stated in the applicable 3M Product Manual in effect at the time of purchase. The warranties stated in the applicable 3M Product Manuals are exclusive and are made in place of any and all express or implied warranties or conditions, including any implied warranty of merchantability or fitness for a particular purpose, or any industry practice or custom or trade usage. Failure to follow the instructions contained in the appropriate 3M Product Manual or to use the 3M Product in accordance with 3M s Intended Use Statement, will void all warranties and limited remedies. EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS) RESULTING FROM, OR IN ANY WAY RELATED TO PERFORMANCE, USE OR INABILITY TO USE ANY OF THE 3M PRODUCT. This limitation applies regardless of the legal theory upon which damages are sought. If 3M Product is defective within the applicable warranty period, your exclusive remedy shall be, at 3M s option, to replace or repair the 3M Product or to refund the purchase price of the 3M Product. All replaced parts or products become property of 3M. If the 3M Product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the product with the same or equivalent model and with a new or refurbished product. In the case of an approved warranty claim, the replacement 3M Product will carry only the remaining term of the original 3M Product s warranty period as stated in the applicable 3M Product Manual. For warranty service, you must provide proof of the date of the original purchase, otherwise the manufacturing code date will be used to establish the start date of the warranty. 3M Product Manuals include durability statements and may include limitations specific to the product(s) being used or its intended applications, which take precedence over any statement made here. Warranty terms, limitations and exclusions may differ outside the United States of America. I have read and understand Signature Date 3M All Rights Reserved. 7 of 7 8 of 38

9 3M SCP Screen Size Chart [A] Note: A & B distance is measured from Top of Image. (Not top of screen) Top of Screen [B] Top of Image Image Area Desired Image Size (4:3) Projector Model Height Width Diagonal SCP712 SCP715/717 SCP716 Clearance Required to Top of Image From Ceiling [A] From Bottom of Cover [B] 36 39" ( m) 48 52" ( m) 60 65" ( m) 19.00" (483 mm) 5.61" (143 mm) 39 42" ( m) 52 56" ( m) 65 70" ( m) 19.27" (489 mm) 5.88" (150 mm) 42 45" ( m) 56 60" ( m) 70 75" ( m) 19.55" (497 mm) 6.16" (156 mm) 45 48" ( m) 60 64" ( m) 75 80" ( m) 19.82" (503 mm) 6.43" (163 mm) 36 39" ( m) 48 52" ( m) 60 65" ( m) 18.64" (473 mm) 5.25" (133 mm) 39 42" ( m) 52 56" ( m) 65 70" ( m) 18.98" (482 mm) 5.59" (142 mm) 42 45" ( m) 56 60" ( m) 70 75" ( m) 19.33" (491 mm) 5.94" (151 mm) 45 48" ( m) 60 64" ( m) 75 80" ( m) 19.67" (500 mm) 6.28" (160 mm) 36 39" ( m) 48 52" ( m) 60 65" ( m) 17.64" (448 mm) 4.18" (106 mm) 39 42" ( m) 52 56" ( m) 65 70" ( m) 17.91" (455 mm) 4.45" (113 mm) 42 45" ( m) 56 60" ( m) 70 75" ( m) 18.19" (462 mm) 4.73" (120 mm) 45 48" ( m) 60 64" ( m) 75 80" ( m) 18.42" (468 mm) 5.00" (127 mm) SCP740 Desired Image Size (16:10) 29 32" ( m) 47 51" ( m) 55 60" ( m) 22.13" (562 mm) 8.74" (222 mm) 32 34" ( m) 51 55" ( m) 60 65" ( m) 22.82" (580 mm) 9.43" (240 mm) 34 37" ( m) 55 59" ( m) 65 70" ( m) 23.53" (598 mm) 10.13" (257 mm) 37 40" ( m) 59 64" ( m) 70 75" ( m) 24.21" (615 mm) 10.82" (275 mm) Note: This document is for reference purposes only. Always refer to the installation instructions packaged with the system. 3 Projection Systems 3M Austin Center 6801 River Place Blvd. Austin, TX meetings@mmm.com 3M is a trademark of 3M Company. Please Recycle. Printed in USA. 3M All Rights Reserved Rev. B

10 3M SCP Screen Size Chart SCPV1 SCPV2 Projector Model Min. Image Size, Diagonal Max. Image Size, Diagonal Min. Image Size, Diagonal Max. Image Size, Diagonal 57.78" (1468 mm) 83.84" (2130 mm) 63.84" (1622 mm) 95.96" (2437 mm) SCP712 SCP715/ " (1200 mm) Not Recommended 70.97" (1803 mm) Not Recommended 52.78" (1341 mm) 82.00" (2083 mm) 52.73" (1339 mm) 78.79" (2001 mm) 58.79" (1493 mm) 90.91" (2309 mm) SCP716 SCP " (1105 mm) Not Recommended 65.33" (1659 mm) Not Recommended 48.58" (1234 mm) 75.48" (1917 mm) SCPV1 SCPV2 Fixed Wall Mount for SCP Products Folding Wall Mount for SCP Products Folding Wall Mount with Speakers (2 20-watt speakers) for SCP Products M Projection Systems products are sold through a network of fully-trained distributors. Contact one of our full-line dealers to place orders. To find a full-line dealer please visit: and select Locate a Servicing or Selling Dealer.

11 Completed Installation Sample#1 Optional channel run molding used to secure wires. Note: In above example, wires are secured using optional (customer supplied) channel run molding. 3M standard installation provides adhesive backed wire tie wraps to secure wires. 37 of 38

12 Completed Installation Sample#2 Optional channel run molding used to secure wires. Note: In above example, wires are secured using optional (customer supplied) channel run molding. 3M standard installation provides adhesive backed wire tie wraps to secure wires. 38 of 38

13 9 of 38

14 3M Annotation Sensor Kit Installation Einrichten Installazione 3M Austin Center Building A147-5N River Place Blvd. Austin, TX M Canada P.O. box 5757 London, Ontario N5V 3R6 3M Mexico, S.a. de C.V Apartado Postal Mexico, D.F Mexico 3M Europe Boulevard de l'oise Cerge Pontoise Cedex France Please recycle. Litho in USA 3M All Rights Reserved (3/2008) 10 of 38

15 Required Tools for SCP 712 install: Step Ladder 1/2" Hammer Drill Motor, 1/2" Masonry Drill Bit and 3/16" Regular Drill Bit Flat Blade Screwdriver Small Side Cutter Set Small Pliers Set #2 Philips Screwdriver Minimum of five 3 wire ties Minimum of five adhesive backed wire tie anchors 11 of 38

16 Required Tools for SCP 712 install, continued 12 tape measure and Small Level Small Socket Set (1/4 to 1/2 range sockets) Hollow wall (Drywall) Stud Locator Wall Mount Bracket Installation Instructions (if bracket is being used) Folding Mount Installation Instructions - or Fixed Mount Installation Instructions (depending on product SKU) 12 of 38

17 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 For use with 3M Super Close Projection System Installation Instructions March of 38

18 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 Safety Instructions Please read and follow all safety information contained in these instructions prior to installation and use of the folding or fixed wall mounts. Retain these instructions for future reference. Intended Use The folding wall mount is intended to provide wall mounting of the 3M Super Close Projection System SCP700 Series projectors to the wall as described in the Installation Instructions. It is expected that all installers and users be fully aware of safe operation of this product. Other applications have not been evaluated by 3M and may lead to an unsafe condition. Explanation of Signal Word Consequences WARNING: Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury and/or property damage. CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury and/or property damage. Summary of device labels containing safety information Caution: Pinch Hazard Warning: Do not hang on the product Attention: Read Accompanying Documentation Caution: Hot Surface Warning: Do not look into the projector lamp WARNING To reduce the risk associated with all applicable hazards: Installation Instructions and Product Safety Guide prior to installing, using or servicing the wall mount. Retain these instructions for future reference. To reduce the risk associated with choking: materials. To reduce the risk associated with impact: installation instructions for details). is properly reinforced. mounted projector around children. of the wall mount. Projection System SCP700 Series projectors only. It has not tightened and that no damage has occurred. Repair or replace all issues found prior to further use. mounting. mounting M. All Rights Reserved. 14 of 38 3

19 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 WARNING To reduce the risk associated with hazardous voltage: found prior to further use. prior to any servicing. To reduce the risk associated with fire: other source of direct heat energy. CAUTION To reduce the risk associated with pinch points: pinch point injury. To reduce the risk associated with lifting: wall mounts per the Installation Instructions due to weight and handling concerns. To reduce the risk associated with impact: SAVE THESE INSTRUCTIONS 4 15 of M. All Rights Reserved.

20 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 1.0 Kit Contents Installation Instructions USB Cable 4m VGA Cable 4m 6x Cable ties 3x M6*25 Screws (for mounting projector) 2x 1-1/2" Lag Bolts 2x ½" Lag Anchors 2x 2-1/2" Lag Bolts 2x 1-1/2" Lag Anchors 3.3 Using a Phillips (+) screwdriver, remove the three screws holding the cover to the base SCPFWMMSV2 Only 1.8 m PC Audio Cable 3 m PC Audio Cable Power Supply for Speaker Amp Power Cord for Speaker Amp EU to UK power outlet adapter (EU/UK only) DC Power Cord (power from I/O to Speaker Amp) Optional Accessories 3M Wall Mount Bracket ( ) 3M Wall Mount Bracket Security Cable ( ) Remove the Cover Remove the Folding Wall Mount from the packaging and set base-down on a table Lift the cover off the base and set aside. Route Cables Feed the USB, VGA, and optional control cables through the arm. Align the cable ends and secure about 6 inches (150 mm) from the end using a cable tie. 3.2 Swing the arm up until it locks in place. ~6" (150 mm) M. All Rights Reserved. 16 of 38 5

21 For use with: SCP715, SCP717, SCP740 SCP715, SCP717 SCP Align the cables alongside the power cable and secure using cable ties. 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 5.3 Using the appropriate bit, drill 4 holes for the mounting lag bolt anchors. Install the short anchors in the upper holes, and the long anchors in the lower holes. Note: Use a 1/2 masonry drill bit for solid concrete walls or a 3/16 drill bit for wood walls. Do not use anchors for wood walls, only use screws. 5.4 Using a 3/8 socket, install the 2 short (upper) mounting lag bolts, leaving 1/2 (13 mm) of the screw protruding from the wall. Do not install the long (lower) lag bolts Solid Wall Installation (For Concrete Block or Stud Walls, Skip to Step 7) Determine desired size and location of projected image and mark the location of the top and center of the image. Locate the top of image line of the template for the desired image size and then align top of image and image center line lines with the location of the desired image size. Then mark the positions of the template s four cross-hairs on the wall /2" (13 mm) Attach to Wall Hang the wall mount base on the mounting lag bolts. Using a 3/8" socket, tighten the mounting lag bolts securely. 3M Folding Wall Mount Mounting Template Image Area 6 17 of M. All Rights Reserved.

22 For use with: SCP715, SCP717, SCP740 SCP715, SCP717 SCP740 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 6.2 Install the long mounting lag bolts through the leveling screws and tighten securely. 7.4 Concrete block walls: Mark the hole positions in the vertical joints between the concrete blocks and then using a 1/2" (13 mm) bit, drill 4 holes 1-5/8" (41 mm) deep into the vertical joints between the concrete blocks. Install 4 long anchors in the holes. CAUTION To reduce the risk associated with impact: short lag anchors. 16 in (406 mm) 6.3 Skip to Step M Wall Mount Bracket Installation (For Use With Concrete Block or Stud Walls) Determine desired size and location of projected image and mark the location of the top and center of the image. Align template with mounting holes in bracket and secure to bracket with tape. Locate the top of image line of the template for the desired image size and then align top of image and image center line lines with the location of the desired image size. Mark positions for four mounting holes according to the next step. 3M Folding Wall Mount Mounting Template 4X LONG Stud walls: Mark the holes at the center of the studs and then using a 3/16" (5 mm) bit, drill 4 holes 1-1/2" (38 mm) deep through the wall into the studs. Align with holes in bracket 1/2 5/8" (13 16 mm) Image Area 4X M. All Rights Reserved. 18 of 38 7

23 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 7.5 Using a 3/8" socket, attach the bracket to the wall using 4 short mounting lag bolts. 8.3 Install the long mounting screws through the leveling screws and tighten securely Attach Wall Mount Base to Bracket Using a screwdriver, install the two short mounting screws with washers in the mounting bracket leaving 1/2 (13 mm) of the screw protruding from the bracket. Do not install the long (lower) mounting screws yet. 2X 2X Install Security Kit (Optional) Attach the optional security cable by either locking it to the mounting bracket security slot (1), looping it through the mounting bracket (2) or looping it through the screw-mount anchor point (3). 8.2 Hang the wall mount base on the mounting screws. Using a screwdriver, tighten the mounting screws securely Note: If using the screw-mount anchor point, secure the anchor point before attaching the cable. 9.2 Feed the security lock cable through the arm. Secure about 6 inches (150 mm) from the end of the existing cable bundle using a cable tie. ~6" (150 mm) 8 19 of M. All Rights Reserved.

24 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 9.3 Route the security cable alongside the bundled cables and attach using cable ties Slide the cover over the arm. Attach the power and audio cables to the existing cable bundle using a cable tie. Leave ( mm) slack cable Connect Power Extension Cable Connect the power extension cable as shown. Secure with cable ties Attach Cover Attach the cover to the base " ( mm) WARNING To reduce the risk of hazardous voltage: Connect Audio Cables (SCPFWMMSV2 only) Connect the power and audio cables to the connections inside the cover. Power Audio M. All Rights Reserved. 20 of 38 9

25 13.0 Attach Projector 13.1 Using two screws and the thumbscrew, attach the mounting bracket to the end of the arm extension as shown. Note: First tighten Phillips head screws snuggly onto the ball swivel and then turn thumbscrew to tighten the clamp onto the ball M Folding Wall Mount SCPFWMV2 and SCPFWMSV2 Assemble Arm Extension Lift the assembly and feed the bundled cables through the open end of the arm extension Attach the projector to the mounting bracket with three screws. Note: Some Models will require two washers per screw to ensure a tight fit Insert the arm extension into the arm as shown Install the 2 screws into the arm retainer of M. All Rights Reserved.

26 3M Folding Wall Mount SCPFWMV2 and SCPFWMSV Pull the cable bundle through the hole at the end of the arm extension Adjust vertical image position by removing the cover, loosening the lower mounting lag bolts or mounting screws, and adjusting the leveling screws. Tighten the lower mounting lag bolts or screws when finished, and replace the cover Connect the cables to the projector according to the Quick Start Guide. Attach the optional security cable to the projector Align Projector Power on unit and change image size by adjusting the arm extension in or out To adjust horizontal image position: 1. Remove the cover. 2. Loosen the adjustment and locking screws. 3. Move the arm left or right to the desired position. 4. Tighten the adjustment and locking screws to secure the arm in the new position. 5. Replace the cover when finished Adjust projector aim by loosening the thumb screw. Adjustment Screw Locking Screw M. All Rights Reserved. 22 of 3811

27 Important Notice guaranteed. use. Warranty; Limited Remedy; Limited Liability. practice or custom or trade usage. Projector Systems 6801 River Place Blvd. Austin, TX Please Recycle. Printed in USA. 3M All Rights Reserved of 38

28 3M Fixed Wall Mount SCPFXWMV2 For use with 3M Super Close Projection System Installation Instructions March of 38

29 3M Fixed Wall Mount SCPFXWMV2 Safety Instructions Please read and follow all safety information contained in these instructions prior to installation and use of the folding or fixed wall mounts. Retain these instructions for future reference. Intended Use The folding wall mount is intended to provide wall mounting of the 3M Super Close Projection System SCP700 Series projectors to the wall as described in the Installation Instructions. It is expected that all installers and users be fully aware of safe operation of this product. Other applications have not been evaluated by 3M and may lead to an unsafe condition. Explanation of Signal Word Consequences WARNING: Indicates a potentially hazardous situation, which if not avoided, could result in death or serious injury and/or property damage. CAUTION: Indicates a potentially hazardous situation, which if not avoided, may result in minor or moderate injury and/or property damage. Summary of device labels containing safety information Caution: Pinch Hazard Warning: Do not hang on the product Attention: Read Accompanying Documentation Caution: Hot Surface Warning: Do not look into the projector lamp WARNING To reduce the risk associated with all applicable hazards: Installation Instructions and Product Safety Guide prior to installing, using or servicing the wall mount. Retain these instructions for future reference. To reduce the risk associated with choking: materials. To reduce the risk associated with impact: installation instructions for details). is properly reinforced. mounted projector around children. of the wall mount. Projection System SCP700 Series projectors only. It has not tightened and that no damage has occurred. Repair or replace all issues found prior to further use. mounting. mounting M. All Rights Reserved. 25 of 38 3

30 3M Fixed Wall Mount SCPFXWMV2 WARNING To reduce the risk associated with hazardous voltage: found prior to further use. prior to any servicing. To reduce the risk associated with fire: other source of direct heat energy. CAUTION To reduce the risk associated with pinch points: pinch point injury. To reduce the risk associated with lifting: wall mounts per the Installation Instructions due to weight and handling concerns. To reduce the risk associated with impact: SAVE THESE INSTRUCTIONS 4 26 of M. All Rights Reserved.

31 For use with: SCP715, SCP717, SCP740 SCP715, SCP717 SCP740 For use with: SCP715, SCP717, SCP740 SCP715, SCP717 SCP740 3M Fixed Wall Mount SCPFXWMV Kit Contents Installation Instructions USB Cable 4m VGA Cable 4m 3x M6*25 Screws (for mounting projector) 4x 1-1/2" Lag Bolts 4x ½" Lag Anchors Optional Accessories 3M Wall Mount Bracket ( ) 3M Wall Mount Bracket Security Cable ( ) Solid Wall Installation (For Concrete Block or Stud Walls, Skip to Step 4) Determine desired size and location of projected image and mark the location of the top and center of the image. Locate the top of image line of the template for the desired image size and then align top of image and image center line lines with the location of the desired image size. Then mark the positions of the template s four cross-hairs on the wall M Wall Mount Bracket Installation (For Use With Concrete Block or Stud Walls) Determine desired size and location of projected image and mark the location of the top and center of the image. Align template with mounting holes in bracket and secure to bracket with tape. Locate the top of image line of the template for the desired image size and then align top of image and image center line lines with the location of the desired image size. Mark positions for four mounting holes according to the next step. 3M Folding Wall Mount Mounting Template Image Area Align with holes in bracket 3M Folding Wall Mount Mounting Template Image Area 4.4 Concrete block walls: Mark the hole positions in the vertical joints between the concrete blocks and then using a 1/2" (13 mm) bit, drill 4 holes 1-5/8" (41 mm) deep into the vertical joints between the concrete blocks. Install 4 long anchors in the holes. CAUTION To reduce the risk associated with impact: short lag anchors. 3.3 Using the appropriate bit, drill 4 holes for the mounting lag bolt anchors. Install the short anchors in the holes. Do not install the lag bolts at this time. Note: Use a 1/2 masonry drill bit for solid concrete walls or a 3/16 drill bit for wood walls. Do not use anchors for wood walls, only use screws. 16 in (406 mm) 3.4 Skip to Step 5. 4X LONG M. All Rights Reserved. 27 of 38 5

32 Stud walls: Mark the holes at the center of the studs and then using a 3/16" (5 mm) bit, drill 4 holes 1-1/2" (38 mm) deep through the wall into the studs. 1/2 5/8" (13 16 mm) M Fixed Wall Mount SCPFXWMV2 Install Security Kit (Optional) Attach the optional security cable by either locking it to the mounting bracket security slot (1), looping it through the mounting bracket (2) or looping it through screw-mount anchor point (3) Note: If using the screw-mount anchor point, secure the anchor point before attaching the cable. 6.2 Feed the security lock cable through the arm. Secure about 6 inches (150 mm) from the end of the existing cable bundle using a cable tie. 4X ~6" (150 mm) 4.5 Using a 3/8" socket, attach the bracket to the wall using 4 short mounting lag bolts Route Cables Feed power, VGA and USB cables through the base section of the arm. Bundle the cables and secure about 6 inches (150 mm) from the end using a cable tie Mount Base to Wall Position the wall mount over the mounting screw anchors or mounting bracket. Install and tighten the 4 mounting screws/mounting lag bolts firmly. ~6" (150 mm) 6 28 of M. All Rights Reserved.

33 3M Fixed Wall Mount SCPFXWMV2 8.0 Attach Projector 8.1 Using two screws and the thumbscrew, attach the mounting bracket to the end of the arm extension as shown. Note: First tighten Phillips head screws snuggly onto the ball swivel and then turn thumbscrew to tighten the clamp onto the ball Assemble Arm Extension Lift the assembly and feed the bundled cables through the open end of the arm extension. 9.2 Insert the arm extension into the arm as shown. 3M All Rights Reserved M. All Rights Reserved. 29 of 38 7

34 3M Fixed Wall Mount SCPFXWMV2 9.3 Install the 2 screws into the arm retainer Adjust projector aim by loosening the thumb screw Adjust vertical image position by turning the leveling screw. 9.4 Pull the cable bundle through the hole at the end of the arm extension Adjust horizontal image position by loosening the four mounting screws and adjusting the base left or right. Tighten the mounting screws when finished Connect the cables to the projector according to the Quick Start Guide. Attach the optional security cable to the projector Align Projector Power on unit and change image size by adjusting the arm extension in or out of M. All Rights Reserved.

35 Important Notice guaranteed. use. Warranty; Limited Remedy; Limited Liability. practice or custom or trade usage. Projector Systems 6801 River Place Blvd. Austin, TX Please Recycle. Printed in USA. 3M All Rights Reserved of 38

36 3M I/O Module SCPI/OV2 Mounting Template 8 15/16" 227 mm 5 3/16" 132 mm /2" (38 mm) 3/16" (5 mm) A B " (25 mm) min. No /4" No. 6-3/4" 32 of M Company.

37 3M Super Close Projection System SCP VAC Hz A/C Power Service Computer/ Component Control Audio Power USB USB Control To Projector Signal Audio Out Audio Computer 2/ Power Component 2 Serial RS Video R Stereo Mini 2 RCA Audio USB Ethernet Computer 1/ Component 1 Computer Out S-Video L Stero Mini 1 Audio Out Audio Computer 2/ Power Component 2 Serial RS232 Video R Stereo Mini 2 RCA Audio USB Ethernet Computer 1/ Component 1 Computer Out S-Video L Stereo Mini 1 Audio Out 33 of 38

38 Installation Checklist Check One Description. Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No Was screen or whiteboard previously installed? If not has projection area been defined and clearly marked with masking tape for future installation? Has projector been installed? Was the Accessory Wall Mount Bracket used? Has the I/O module been installed (if required)? Was the Annotation pod installed (if required)? Have the cables been neatly secured and routed? Has the projector been properly aligned to project a square image on the screen? Has the Annotation Software been loaded onto the meeting room PC and the CD been provided to the customer? Did the Annotation Software launch and recognize the attached Annotation pod? Has the system been calibrated to the expected screen size and position? Have the following tasks been performed successfully using the Annotation Pen? 1. Open ebeam Scrapbook file (requires PC mouse selection for first launch) and make full screen using pen (maximize the window) 2. Test APPLICATION Icon in top left corner (Figure 1) 3. Test FILE menu item (Figure 2) 4. Test MINIMIZE icon (top right) (Figure 3 ) 5. Test RESTORE icon (top right) (Figure 3) 6. Test CLOSE icon (top right) (Figure 3) 7. Exit 3M Digital Annotation software (close software) Have the tools been put away and the installation site cleaned? Has this checklist been reviewed with the customer for any additional actions needed (please ask they sign below)? Please explain any No answer: I accept the installation. Signature Title Date 34 of 38

39 Installation Checklist (continued) FIGURE 1 Application Icon Application Menu FIGURE 2 File button File menu 35 of 38

40 Installation Checklist (continued) FIGURE 3 Minimize Restore Close 36 of 38