VCU110 Software Install and Board Setup October 2015

Transcription

1 VCU110 Software Install and Board Setup October 2015 XTP380

2 Revision History Date Version Description 11/20/ Modified to match VCU110 Kit hardware. 10/22/ Added ExaMax and Interlaken setup. 10/06/ Initial version. Copyright 2015 Xilinx, Inc. All Rights Reserved. XILINX, the Xilinx logo, the Brand Window and other designated brands included herein are trademarks of Xilinx, Inc. All other trademarks are the property of their respective owners. NOTICE OF DISCLAIMER: The information disclosed to you hereunder (the Information ) is provided AS-IS with no warranty of any kind, express or implied. Xilinx does not assume any liability arising from your use of the Information. You are responsible for obtaining any rights you may require for your use of this Information. Xilinx reserves the right to make changes, at any time, to the Information without notice and at its sole discretion. Xilinx assumes no obligation to correct any errors contained in the Information or to advise you of any corrections or updates. Xilinx expressly disclaims any liability in connection with technical support or assistance that may be provided to you in connection with the Information. XILINX MAKES NO OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY, REGARDING THE INFORMATION, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY RIGHTS.

3 Note: This presentation applies to the VCU110 VCU110 Software Install and Board Setup Xilinx VCU110 Board Software Requirements VCU110 Hardware Setup UART Driver Install Clock Setup Ethernet Setup Optional Hardware Setup References

4 Xilinx VCU110 Board

5 Note: Presentation applies to the VCU110 Software Requirements Xilinx Vivado Design Suite , Design Edition with SDK

6 Note: Presentation applies to the VCU110 VCU110 Hardware Setup Kit Hardware contents VCU110 Board One CFP4 Loopback One BullsEye cable (not shown) Two XM107 FMC Loopback boards Ethernet cable Two Micro USB cables 180 W Power supply (not shown)

7 VCU110 Hardware Setup CFP4 Loopback Adapter Part # ML4050 For the Board Interface Test, begin with the CFP4 Loopback in slot MOD0 Note: Presentation applies to the VCU110

8 Note: Presentation applies to the VCU110 VCU110 Hardware Setup Attach the two FMC XM107 boards to the FMC connectors, J2 and J22

9 VCU110 Hardware Setup Connect a USB Type-A to Micro-B cable to the USB UART connector (J4) on the VCU110 board Connect a USB Type-A to Micro-B cable to the USB JTAG (Digilent) (J135) connector on the VCU110 board Connect the Ethernet cable to P3 Connect these cables to your PC Note: Presentation applies to the VCU110

10 VCU110 Hardware Setup BullsEye Loopback Adapter Part # HDR BEYE Note: Presentation applies to the VCU110

11 Note: Presentation applies to the VCU110 VCU110 Hardware Setup SMA Connector Part # Connect BullsEye cable: and (Link 3) and (Link 2) and (Link 1) and (Link 0) Connect GTY Ref Clock to 175 MHz clock source (not included) Connect to BullsEye Clocks: 019 and 020 (GTY Ref Clock)

12 Note: Presentation applies to the VCU110 VCU110 Hardware Setup BullsEye Loopback Adapter Elastomer must be installed Note the larger and smaller alignment pins

13 VCU110 Hardware Setup BullsEye Loopback Adapter Attach to VCU110, observing the larger and smaller alignment pins Note: Presentation applies to the VCU110

14 VCU110 Hardware Setup Attach to J87, initially, for the Board Interface Test Note: Presentation applies to the VCU110

15 VCU110 Hardware Setup Connect the power supply to the VCU110 (J15) Connect this power supply to a power outlet Power on the VCU110 board for the UART driver installation Note: Presentation applies to the VCU110

16 VCU110 Hardware Setup Watch your fingers around the fan when board is powered on Fan blades will break Fan model: Cofan F-7015HH12B Note: Presentation applies to the VCU110

17 Note: Presentation applies to the VCU110 UART Driver Install Install Si Labs CP210x USB UART Drivers Refer to UG1033 for details on installing the USB to UART Drivers

18 Note: Presentation applies to the VCU110 UART Driver Install Determine the COM Port numbers for your system Open the Device manager Control Panel System Device Manager There will be two Silicon Labs Dual CP210x COM ports, Standard and Enhanced The Standard COM Port is the FPGA UART COM Port The Enhanced COM Port is the System Controller COM Port The COM Port numbers will vary from system to system These COM Port Numbers will be used in several of the tutorials

19 Note: See AR63771 regarding SDK Terminal Program Terminal Setup Refer to UG1036 regarding Tera Term installation Board Power must be on before starting Tera Term Start the Terminal Program and select your USB Com Port

20 Note: Presentation applies to the VCU110 Terminal Setup Set the baud to

21 Note: Presentation applies to the VCU110 Clock Setup Needed for IBERT and IPI designs The Board Interface Test sets the Clocks automatically Open a Terminal window for the Enhanced COM Port Cycle board power and review System Controller UART output

22 Note: Presentation applies to the VCU110 Clock Setup The Si5328s must be set when power is cycled Press the Enter key after each entry Press 1, 2, and to set the CFP4 Si5328 frequency

23 Note: Presentation applies to the VCU110 Clock Setup Press 3, and 175 to set the Interlaken and ExaMax Si5328 frequency

24 Note: Presentation applies to the VCU110 Clock Setup Press 5 to set the HMC Frequency for the IPI Clock Test The HMC IBERT Test will set it s own frequency automatically

25 Note: Presentation applies to the VCU110 Clock Setup Press 0 to return to the main menu

26 Note: Clocking test will pass with FMC MHz Clock Setup The IBERT GTH tests require clocks from the FMC Si570s Frequency must be set to 163 MHz for the GTH tests Press 4, 1, and 4

27 Note: FMC Si570s revert to MHz when power is cycled Clock Setup Set both FMC cards to 163 MHz Press 1 then 163 to set XM107 on FMC HPC0 to 163 MHz

28 Note: Presentation applies to the VCU110 Clock Setup Set both FMC cards to 163 MHz Press 2 then 163 to set XM107 on FMC HPC1 to 163 MHz

29 Note: Presentation applies to the VCU110 Ethernet Setup Open the Windows Control Panel Set to View by Category Click on View network status and tasks

30 Note: Presentation applies to the VCU110 Ethernet Setup Click on Change adapter settings

31 Note: Presentation applies to the VCU110 Ethernet Setup Right-click on the Gigabit Ethernet Adapter that you will be using for this test and select Properties

32 Note: Presentation applies to the VCU110 Ethernet Setup Click Configure Set the Link Speed & Duplex to Auto Negotiation then click OK

33 Note: Remember to restore your IP settings when finished Ethernet Setup Reopen the properties after the last step Double-click the Internet Protocol Version 4 Set your host (PC) to this IP Address:

34 Optional Hardware Setup Jumper the PMOD header On header J52, connect: 1 to 2 3 to 4 5 to 6 7 to 8 Note: Presentation applies to the VCU110

35 Note: Presentation applies to the VCU110 Optional Hardware Setup The VCU110 IPI LVDS Loopback test requires two XM105 boards On the XM105 s J1 connector, connect all pins as follows: 1 to 3 2 to 4 5 to 7 37 to to 40 Also connect TDO to TDI on J5

36 Optional ExaMax/Interlaken Hardware Setup For use with XTP381 ExaMax and Interlaken Testing requires TWO VCU110 boards Requires an ExaMax backplane from one of these vendors: FCI ExaMax Backplane (Megtron 6 PCB material) examax.fci.com/ Part number: PCB Samtec ExaMax Backplane (Tachyon PCB material) Part number: ExaMax HSBP-1 Interlaken cable TE Connectivity Part number: Note: XM107 FMC cards must be removed before inserting the VCU110 into an ExaMax chassis

37 Optional ExaMax/Interlaken Hardware Setup If needed, adjust the metal supports and corresponding backplane spikes to the wide positions For the FCI Backplane, use the slots marked OIF Compliant For the Samtec Backplane, use slots J5 and J10 Very carefully insert the two VCU110 boards into the backplane Carefully attach the Interlaken cable to the two VCU110 boards Note: Presentation applies to the VCU110

38 Optional ExaMax/Interlaken Hardware Setup Connect a USB Type-A to Micro-B cable to the USB UART connector on both VCU110 boards Connect a USB Type-A to Micro-B cable to the USB JTAG (Digilent) connector on both VCU110 boards Connect these four cables to your PC Note: Presentation applies to the VCU110

39 Optional ExaMax/Interlaken Hardware Setup With 4 USB Micro cables connected Note: Presentation applies to the VCU110

40 Optional ExaMax/Interlaken Hardware Setup Connect two 180 w Power supplies to the two VCU110 boards Note: Presentation applies to the VCU110

41 Note: Presentation applies to the VCU110 Optional ExaMax/Interlaken Hardware Setup Verify the COM ports setup Right-click on My Computer and select Properties Click on Device Manager

42 Note: Presentation applies to the VCU110 Optional ExaMax/Interlaken Hardware Setup Expand the Ports Hardware Four Silicon Labs UART ports should appear XTP381 test requires that there are exactly 2 Enhanced COM ports present

43 References

44 References Vivado Release Notes Vivado Design Suite User Guide - Release Notes UG973 ug973-vivado-release-notes-install-license.pdf Vivado Design Suite 2015.x - Vivado Known Issues Vivado Programming and Debugging Vivado Design Suite Programming and Debugging User Guide UG908 ug908-vivado-programming-debugging.pdf

45 Documentation

46 Documentation Virtex UltraScale Virtex UltraScale FPGA Family VCU110 Documentation Virtex UltraScale FPGA VCU110 Development Kit VCU110 - Known Issues Master Answer Record