Consult factory for all other Models GE RELAY L2 BLACK BLACK RELAY COM 3 BLACK OR BLUE WHITE WHITE CAPACITOR RED YELLOW BLUE YELLOW (3) BLUE RED

Transcription

1 Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies. MAIL TO: P.O. BOX 7 Louisville, KY 0-07 SHIP TO: 9 Cane Run Road Louisville, KY 0-9 TEL: (0) (800) 98-PUMP FAX: (0) 77- REPLACEMENT PARTS LIST FOR MODELS: H8 AUTOMATIC 00V/PH I8 NONAUTOMATIC 00V/PH J8 NONAUTOMATIC 00V/PH F8 NONAUTOMATIC 0V/PH G8 NONAUTOMATIC 0V/PH BA8 NONAUTOMATIC 7V/PH Visit our web site: zoellerpumps.com FM09 0 Supersedes 0 Consult factory for all other Models GE RELAY GE RELAY R R L L L L L L RELAY SWITCH RELAY R 0 COM NC R 0 COM NC GREEN CAPACITOR GRAY FLOAT GREEN OR FLOAT GREEN CAPACITOR CAPACITOR () () () () () () () () () () (BROWN) () () (BROWN) () () (BROWN) () MOTOR MOTOR MOTOR O.L. O.L. O.L. START RUN INSULATORS REQUI ON GE RELAY TERMINALS & ; OMRON RELAY TERMINALS &. START RUN INSULATORS REQUI ON GE RELAY TERMINALS & ; OMRON RELAY TERMINALS & RUN START WIRING DIAGRAM FOR MODEL H8-A /8 (XM) 8/8 (US) WIRING DIAGRAM FOR MODELS H8-B, H8-C, and H8-E 9/8 (VS) WIRING DIAGRAM FOR MODELS I8 All Revisions /8 (XM) L L L TO ORDER REPLACEMENT PARTS: GREEN PLEASE FURNISH THE FOLLOWING INFORMATION: () () MOTOR () Model Number. Part Number of Pump. (If manufactured prior to June 988, give letter date code following Model No.) Part Number and Description of part WIRING DIAGRAM FOR MODELS J8 All Revisions, /8 (XM) F8 All Revisions 9/8 (VS) G8 All Revisions 9/8 (VS) BA8 All Revisions /0 (VS) Copyright 0 Zoeller Co. All rights reserved.

2 REPLACEMENT PARTS LIST FOR MODELS H8 NO. DESCRIPTION QTY NOTES MODELS: H8-A H8-B H8-C H8-D H8-E /8 XM 8/8 US 9/8 VS /9 /9 /0 /0 / / Case, Sw.& Cord Guard Case-Mach, Arm & Seal Asm Gasket, Case/Cover Switch Asm Wire Pkg () Wires Relay Capacitor & Clamp Asm Float, Plastic Guide Asm, Flt Rod Rod Asm, Flt Housing, Mtr-& Str, NA NA Bearing, Radial NA NA NA Handle Cord, Term & Seal Asm, Clamp, Strain Relief, 7 NA NA NA NA NA 8 Seal, Cord-Asm & Strain Relief Plug, Test-White Seal, Thru Wall Term Rotor & Brg Bearing, Radial Seal, Mtr Hsg Oil, Dielectric Adapter-Mach Seal, Shaft Flange Pkg Npt Flange Pkg Npt Impeller Housing, Pump-Mach Screw, #0- X.7 RHM-Sl SS Screw, #-x.rhm Sl Tc Stlgr Screw,.-0 X.7 HHm-SS Screw, #-x.8 Rhsltp Stlzi Screw,.- X HH Cap-SS Washer, SS-. Odx. Idx Screw,.-8 X HH Cap-SS Screw,.-0x HHm-SS Rebuild Kit See page 7 for H8 illustration. ) Mtr. Hsg., Brg., Stator & Term. (Item ) are preassembled at the factory and must be replaced as a unit. Stator is permanently attached to the motor Housing. Plug (Item 9); Seal, Thru Wall Term. (Item 0) and Bearing - Upper (Item ) are replaceable. ) When ordering these parts, customer must identify if switch is a General Electric switch. ) If an X follows Model No., or Date Mfg. on brass ID tag, consult factory for ordering any parts. ) See FM00 Parts Price Sheet for listing of parts prices. ) NA indicates, not applicable. ) When ordering Motor Housing, Bearing, Stator and Term. (Item ) or Rotor (Item ) specify either GE or Emerson motor. GE motor can be identified by () holes spaced at 90 around the outside diameter of the stator. Emerson motor can be identified by () flat edges spaced at 90 around the outside diameter of the stator. 7) Clamp, Strain Relief (Item 7) is not sold separately, must order Seal, Cord Asm (Item 8). Copyright 0 Zoeller Co. All rights reserved.

3 REPLACEMENT PARTS LIST FOR MODELS I8 NO. DESCRIPTION QTY NOTES MODELS: I8-A I8-B I8-C I8-D /8 XM 8/8 US 9/8 VS /9 /9 0/0 0/0 Cover & Cord Cover-Mach Gasket, Case/Cover Wire Pkg Capacitor & Clamp Asm Housing, Mtr-& Str, NA Bearing, Radial NA NA NA Handle Cord, Term, & Seal Asm Clamp, Strain Relief Seal, Cord-Asm & Relief Plug, Test-White Seal, Thru Wall Term Rotor & Brg Bearing, Radial Seal, Mtr Hsg Oil, Dielectric Adapter-Mach Seal, Shaft Flange Pkg Npt Flange Pkg Npt Impeller Housing, Pump-Mach Screw, #-x.rhm Sl Tc Stlgr Screw, #0- X.7 RHM-Sl SS Screw,.-0 X.7 HHm-SS Screw,.- X HH Cap-SS Washer, SS-. Odx. Idx Screw,.-8 X HH Cap-SS Screw,.-0x HHm-SS Rebuild Kit See page 7 for I8 illustration. ) Mtr. Hsg., Brg., Stator & Term. (Item ) are preassembled at the factory and must be replaced as a unit. Stator is permanently attached to the Motor Housing. Plug (Item ); Seal, Thru Wall Term. (Item ) and Bearing - Upper (Item 7) are replaceable. ) When ordering Motor Housing, Bearing, Stator and Term. (Item ) or Rotor (Item ) specify either GE or Emerson motor. GE motor can be identified by () holes spaced at 90 around the outside diameter of the stator. Emerson motor can be identified by () flat edges spaced at 90 around the outside diameter of the stator. ) If an X follows Model No., or Date Mfg. on brass ID tag, consult factory for ordering any parts. ) See FM00 Parts Price Sheet for listing of parts prices. ) NA indicates, not applicable. Copyright 0 Zoeller Co. All rights reserved.

4 REPLACEMENT PARTS LIST FOR MODELS J8 NO. DESCRIPTION QTY NOTES MODELS: J8-A J8-B J8-C J8-D /8 XM 8/8 US 9/8 VS /9 /9 0/0 0/0 Handle Cover & Cord Cover-Mach Gasket, Case/Cover Housing, Mtr-& Str, NA Bearing, Radial NA NA NA Clamp, Strain Relief Cord, Term, & Seal Asm Seal, Cord-Asm & Relief Plug, Test-White Seal, Thru Wall Term Rotor & Brg Bearing, Radial Seal, Mtr Hsg Oil, Dielectric Adapter-Mach Seal, Shaft Impeller Asm Flange Pkg Npt Flange Pkg Npt Housing, Pump-Mach Screw, #-x.rhm Sl Tc Stlgr Screw,.-0 X.7 HHm-SS Screw,.-8 X HH Cap-SS Screw,.- X HH Cap-SS Washer, SS-. Odx. Idx Screw, #0- X.7 RHM-Sl SS Screw,.-0x HHm-SS Nut, 7/-0 Acorn SS Rebuild Kit See back page for J8 illustration. ) Mtr. Hsg., Brg., Stator & Term. (Item ) are preassembled at the factory and must be replaced as a unit. Stator is permanently attached to the Motor Housing. Plug (Item 0); Seal, Thru Wall Term. (Item ) and Bearing - Upper (Item ) are replaceable. ) When ordering Motor Housing, Bearing, Stator and Term. (Item ) or Rotor (Item ) specify either GE or Emerson motor. GE motor can be identified by () holes spaced at 90 around the outside diameter of the stator. Emerson motor can be identified by () flat edges spaced at 90 around the outside diameter of the stator. ) If an X follows Model No., or Date Mfg. on brass ID tag, consult factory for ordering any parts. ) See FM00 Parts Price Sheet for listing of parts prices. ) NA indicates, not applicable. Copyright 0 Zoeller Co. All rights reserved.

5 REPLACEMENT PARTS LIST FOR MODELS F8 NO. DESCRIPTION QTY NOTES MODELS: F8-A F8-B F8-C 9/8 VS /9 /9 0/0 0/0 Handle Cover & Cord Cover-Mach Gasket, Case/Cover Housing, Mtr-& Str, NA Bearing, Radial NA NA Clamp, Strain Relief Cord, Term, & Seal Asm Seal, Cord-Asm & Relief Plug, Test-White Seal, Thru Wall Term Rotor & Brg Bearing, Radial Seal, Mtr Hsg Oil, Dielectric Adapter-Mach Seal, Shaft Impeller Asm Flange Pkg Npt Flange Pkg Npt Housing, Pump-Mach Screw, #-x.rhm Sl Tc Stlgr Screw,.-0 X.7 HHm-SS Screw,.-8 X HH Cap-SS Screw,.- X HH Cap-SS Washer, SS-. Odx. Idx Screw, #0- X.7 RHM-Sl SS Screw,.-0x HHm-SS Nut, 7/-0 Acorn SS Rebuild Kit See back page for F8 illustration. ) Mtr. Hsg., Brg., Stator & Term. (Item ) are preassembled at the factory and must be replaced as a unit. Stator is permanently attached to the Motor Housing. Plug (Item 0); Seal, Thru Wall Term. (Item ) and Bearing - Upper (Item ) are replaceable. ) When ordering Motor Housing, Bearing, Stator and Term. (Item ) or Rotor (Item ) specify either GE or Emerson motor. GE motor can be identified by () holes spaced at 90 around the outside diameter of the stator. Emerson motor can be identified by () flat edges spaced at 90 around the outside diameter of the stator. ) If an X follows Model No., or Date Mfg. on brass ID tag, consult factory for ordering any parts. ) See FM00 Parts Price Sheet for listing of parts prices. ) NA indicates, not applicable. Copyright 0 Zoeller Co. All rights reserved.

6 REPLACEMENT PARTS LIST FOR MODELS G8 & BA8 See back page for G8 & BA8 illustration. NO. DESCRIPTION QTY NOTES MODELS: G8-A G8-B G8-C BA8-A 9/8 VS /9 /9 0/0 0/0 0/0 Handle Cover & Cord Cover-Mach Gasket, Case/Cover Housing, Mtr-& Str, NA NA Bearing, Radial NA NA Clamp, Strain Relief Cord, Term, & Seal Asm Seal, Cord-Asm & Relief Plug, Test-White Seal, Thru Wall Term Rotor & Brg Bearing, Radial Seal, Mtr Hsg Oil, Dielectric Adapter-Mach Seal,Shaft Impeller Asm Flange Pkg Npt Flange Pkg Npt Housing, Pump-Mach Screw, #-x.rhm Sl Tc Stlgr Screw,.-0 X.7 HHm-SS Screw,.-8 X HH Cap-SS Screw,.- X HH Cap-SS Washer, SS-. Odx. Idx Screw, #0- X.7 RHM-Sl SS Screw,.-0x HHm-SS Nut, 7/-0 Acorn SS Rebuild Kit ) Mtr. Hsg., Brg., Stator & Term. (Item ) are preassembled at the factory and must be replaced as a unit. Stator is permanently attached to the Motor Housing. Plug (Item 0); Seal, Thru Wall Term. (Item ) and Bearing - Upper (Item ) are replaceable. ) When ordering Motor Housing, Bearing, Stator and Term. (Item ) or Rotor (Item ) specify either GE or Emerson motor. GE motor can be identified by () holes spaced at 90 around the outside diameter of the stator. Emerson motor can be identified by () flat edges spaced at 90 around the outside diameter of the stator. ) If an X follows Model No., or Date Mfg. on brass ID tag, consult factory for ordering any parts. ) See FM00 Parts Price Sheet for listing of parts prices. ) NA indicates, not applicable. Copyright 0 Zoeller Co. All rights reserved.

7 REPLACEMENT PARTS ILLUSTRATION FOR MODEL H REPLACEMENT PARTS ILLUSTRATION FOR MODEL I SK Copyright 0 Zoeller Co. All rights reserved. 7 9 SK

8 REPLACEMENT PARTS ILLUSTRATION FOR MODELS J, F, G & BA SK8 MAIL TO: P.O. BOX 7 Louisville, KY 0-07 SHIP TO: 9 Cane Run Road Louisville, KY 0-9 (0) (800) 98-PUMP FAX (0) 77- Visit our web site: zoellerpumps.com Copyright 0 Zoeller Co. All rights reserved. 8