Hardware User Manual EA9-USER-M

Transcription

1 Hardware User Manual E-USER-M

2

3 ~ WRNING ~ Thank you for purchasing automation equipment from utomationdirect.com, doing business as, utomationirect. We want your new automation equipment to operate safely. nyone who installs or uses this equipment should read this publication (and any other relevant publications) before installing or operating the equipment. To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and usually change with time. It is your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation is in compliance with the latest revision of these codes. t a minimum, you should follow all applicable sections of the National Fire ode, National Electrical ode, and the codes of the National Electrical Manufacturer s ssociation (NEM). There may be local regulatory or government offices that can also help determine which codes and standards are necessary for safe installation and operation. Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation. Our products are not fault-tolerant and are not designed, manufactured or intended for use or resale as on-line control equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the failure of the product could lead directly to death, personal injury, or severe physical or environmental damage ( High Risk ctivities ). utomationirect specifically disclaims any expressed or implied warranty of fitness for High Risk ctivities. For additional warranty and safety information, see the Terms and onditions section of our catalog. If you have any questions concerning the installation or operation of this equipment, or if you need additional information, please call us at This publication is based on information that was available at the time it was printed. t utomationirect we constantly strive to improve our products and services, so we reserve the right to make changes to the products and/or publications at any time without notice and without any obligation. This publication may also discuss features that may not be available in certain revisions of the product. Trademarks This publication may contain references to products produced and/or offered by other companies. The product and company names may be trademarked and are the sole property of their respective owners. utomationirect disclaims any proprietary interest in the marks and names of others. opyright 0, utomationdirect.com Incorporated ll Rights Reserved No part of this manual shall be copied, reproduced, or transmitted in any way without the prior, written consent of utomationdirect.com Incorporated. utomationirect retains the exclusive rights to all information included in this document.

4 ~ VERTENI ~ Gracias por comprar equipo de automatización de utomationdirect.com. eseamos que su nuevo equipo de automatización opere de manera segura. ualquier persona que instale o use este equipo debe leer esta publicación (y cualquier otra publicación pertinente) antes de instalar u operar el equipo. Para reducir al mínimo el riesgo debido a problemas de seguridad, debe seguir todos los códigos de seguridad locales o nacionales aplicables que regulan la instalación y operación de su equipo. Estos códigos varian de área en área y usualmente cambian con el tiempo. Es su responsabilidad determinar cuales códigos deben ser seguidos y verificar que el equipo, instalación y operación estén en cumplimiento con la revisión mas reciente de estos códigos. omo mínimo, debe seguir las secciones aplicables del ódigo Nacional de Incendio, ódigo Nacional Eléctrico, y los códigos de (NEM) la sociación Nacional de Fabricantes Eléctricos de US. Puede haber oficinas de normas locales o del gobierno que pueden ayudar a determinar cuales códigos y normas son necesarios para una instalación y operación segura. Si no se siguen todos los códigos y normas aplicables, puede resultar en daños al equipo o lesiones serias a personas. No garantizamos los productos descritos en esta publicación para ser adecuados para su aplicación en particular, ni asumimos ninguna responsabilidad por el diseño de su producto, la instalación u operación. Nuestros productos no son tolerantes a fallas y no han sido diseñados, fabricados o intencionados para uso o reventa como equipo de control en línea en ambientes peligrosos que requieren una ejecución sin fallas, tales como operación en instalaciones nucleares, sistemas de navegación aérea, o de comunicación, control de tráfico aéreo, máquinas de soporte de vida o sistemas de armamentos en las cuales la falla del producto puede resultar directamente en muerte, heridas personales, o daños físicos o ambientales severos ( ctividades de lto Riesgo ). utomationdirect.com específicamente rechaza cualquier garantía ya sea expresada o implicada para actividades de alto riesgo. información adicional acerca de garantía e información de seguridad, vea la sección de Términos y ondiciones de nuestro catálogo. Si tiene alguna pregunta sobre instalación u operación de este equipo, o si necesita información adicional, por favor llámenos al número en Estados Unidos. Esta publicación está basada en la información disponible al momento de impresión. En utomationdirect.com nos esforzamos constantemente para mejorar nuestros productos y servicios, así que nos reservamos el derecho de hacer cambios al producto y/o a las publicaciones en cualquier momento sin notificación y sin ninguna obligación. Esta publicación también puede discutir características que no estén disponibles en ciertas revisiones del producto. Marcas Registradas Esta publicación puede contener referencias a productos producidos y/u ofrecidos por otras compañías. Los nombres de las compañías y productos pueden tener marcas registradas y son propiedad única de sus respectivos dueños. utomationdirect.com, renuncia cualquier interés propietario en las marcas y nombres de otros. PROPIE LITERRI 0, UTOMTIONIRET.OM INORPORTE Todos los derechos reservados No se permite copiar, reproducir, o transmitir de ninguna forma ninguna parte de este manual sin previo consentimiento por escrito de utomationdirect.com Incorprated. utomationdirect.com retiene los derechos exclusivos a toda la información incluida en este documento. Los usuarios de este equipo pueden copiar este documento solamente para instalar, configurar y mantener el equipo correspondiente. También las instituciones de enseñanza pueden usar este manual para propósitos educativos. Para

5 ~ VERTISSEMENT ~ Nous vous remercions d avoir acheté l équipement d automatisation de utomationdirect.com, en faisant des affaires comme, utomationirect. Nous tenons à ce que votre nouvel équipement d automatisation fonctionne en toute sécurité. Toute personne qui installe ou utilise cet équipement doit lire la présente publication (et toutes les autres publications pertinentes) avant de l installer ou de l utiliser. fin de réduire au minimum le risque d éventuels problèmes de sécurité, vous devez respecter tous les codes locaux et nationaux applicables régissant l installation et le fonctionnement de votre équipement. es codes diffèrent d une région à l autre et, habituellement, évoluent au fil du temps. Il vous incombe de déterminer les codes à respecter et de vous assurer que l équipement, l installation et le fonctionnement sont conformes aux exigences de la version la plus récente de ces codes. Vous devez, à tout le moins, respecter toutes les sections applicables du ode national de prévention des incendies, du ode national de l électricité et des codes de la National Electrical Manufacturer s ssociation (NEM). es organismes de réglementation ou des services gouvernementaux locaux peuvent également vous aider à déterminer les codes ainsi que les normes à respecter pour assurer une installation et un fonctionnement sûrs. L omission de respecter la totalité des codes et des normes applicables peut entraîner des dommages à l équipement ou causer de graves blessures au personnel. Nous ne garantissons pas que les produits décrits dans cette publication conviennent à votre application particulière et nous n assumons aucune responsabilité à l égard de la conception, de l installation ou du fonctionnement de votre produit. Nos produits ne sont pas insensibles aux défaillances et ne sont ni conçus ni fabriqués pour l utilisation ou la revente en tant qu équipement de commande en ligne dans des environnements dangereux nécessitant une sécurité absolue, par exemple, l exploitation d installations nucléaires, les systèmes de navigation aérienne ou de communication, le contrôle de la circulation aérienne, les équipements de survie ou les systèmes d armes, pour lesquels la défaillance du produit peut provoquer la mort, des blessures corporelles ou de graves dommages matériels ou environnementaux («activités à risque élevé»). La société utomationirect nie toute garantie expresse ou implicite d aptitude à l emploi en ce qui a trait aux activités à risque élevé. Pour des renseignements additionnels touchant la garantie et la sécurité, veuillez consulter la section Modalités et conditions de notre documentation. Si vous avez des questions au sujet de l installation ou du fonctionnement de cet équipement, ou encore si vous avez besoin de renseignements supplémentaires, n hésitez pas à nous téléphoner au ette publication s appuie sur l information qui était disponible au moment de l impression. À la société utomationirect, nous nous efforçons constamment d améliorer nos produits et services. est pourquoi nous nous réservons le droit d apporter des modifications aux produits ou aux publications en tout temps, sans préavis ni quelque obligation que ce soit. La présente publication peut aussi porter sur des caractéristiques susceptibles de ne pas être offertes dans certaines versions révisées du produit. Marques de commerce La présente publication peut contenir des références à des produits fabriqués ou offerts par d autres entreprises. Les désignations des produits et des entreprises peuvent être des marques de commerce et appartiennent exclusivement à leurs propriétaires respectifs. utomationirect nie tout intérêt dans les autres marques et désignations. opyright 0, utomationdirect.com Incorporated Tous droits réservés Nulle partie de ce manuel ne doit être copiée, reproduite ou transmise de quelque façon que ce soit sans le consentement préalable écrit de la société utomationdirect.com Incorporated. utomationirect conserve les droits exclusifs à l égard de tous les renseignements contenus dans le présent document.

6

7 HRWRE USER MNUL Please include the Manual Number and the Manual Issue, both shown below, when communicating with Technical Support regarding this publication. Manual Number: E-USER-M Issue: st Edition Revision G Issue ate: 0/ Publication History Issue ate escription of hanges First Edition 0/ Original st Ed. Rev. 0/ Minor Revisions st Ed. Rev. 0/ Revised PL communication and drivers, minor revisions st Ed. Rev. 0/ dded Recovery Tool and No System Found to Troubleshooting, minor revisions st Ed. Rev. / dded E-TL(-R). dded ppendix, minor revisions st Ed. Rev. E / dded E-T0WL and E-TL-R. Minor revisions st Ed. Rev. F 0/ Revised Memory evice Formatting table st Ed. Rev. G 0/ orrected H-L description

8

9 Table of ontents hapter : Getting Started Introduction...- The Purpose of this Manual...- Supplemental Manuals...- Technical Support...- onventions Used...- Key Topics for Each hapter...- Product Overview...- Quick Start Steps...- Step Unpack and Inspect...- Step Install Optional Hardware ccessories...- Step ecome Familiar with vailable ommunication Ports...- Step Install the Programming Software and evelop a Project...- Step onnect Touch Panel to omputer...- Step Provide Power to the Touch Panel...-0 Step ccess the Touch Panel Setup Screens...- Step hoose Touch Panel to evice Protocol & ables...- Step onnect Touch Panel to PL...- hapter : Specifications vailable Models...- Model Specifications...- Specifications common to all models...- -inch Models...- -inch Models...- -inch and 0-inch Models...- -inch and -inch Models...-0

10 Table of ontents E-TL-R, E-TL... - imensions, Inches [mm]... - Ports and Memory Expansion... - E-TL-R, E-TL... - imensions, Inches [mm]... - Ports and Memory Expansion... - E-TL... - imensions, Inches [mm]... - Ports and Memory Expansion... - E-T0L... - imensions, Inches [mm]... - E-T0WL... - imensions, Inches [mm]... - Ports and Memory Expansion... - E-TL imensions, Inches [mm] Ports and Memory Expansion... - E-TL-R, E-TL... - imensions, Inches [mm]... - Ports and Memory Expansion... - Mounting learances... - E-TL-R, E-TL erating... - ommunications Ports... - Handling External Memory evices Writing to External Memory evices Memory evice Formatting Minimizing ata Errors... - Monitoring vailable Memory... - File Name Limitations... - Power Loss Retention... - hemical ompatibility... - hapter : ccessories ii E-USER-M Hardware User Manual, st Ed. Rev. G

11 Table of ontents ccessories Overview... - / Power dapter... - / Power dapter imensions... - / Power dapter Installation SU -pin to Terminal lock dapters... - Non-glare Screen overs... - lear Screen Overlay Installation... - S ard US FLSH rive hapter : Installation and Wiring Safety Guidelines... - Introduction... - E-TL-R, E-TL, E-TL-R and E-TL utout imensions... - E-TL and E-T0WL utout imensions... - E-TL utout imensions... - E-TL-R and E-TL utout imensions... - Mounting learances... - E-TL-R, E-TL erating Wiring Guidelines... - gency pprovals... - Providing Power to the Touch Panel more LE Status Indicators... - hapter : System Setup Screens Introduction... - ccessing the System Setup Screens (no project loaded)... - ccessing the System Setup Screens (with project loaded)... - System Setup Screens Enable Password in Software... - System Setup Screens Flowchart... - Main Menu... - E-USER-M Hardware User Manual, st Ed. Rev. G iii

12 Table of ontents Information Menu... - Setting Menu... - Test Menu... - Memory Menu... - hapter : PL ommunications Introduction... - irectlogi PLs Password Protection... - PL Protocol & ables... - PL ommunication ables & Wiring iagrams... - utomationirect PLs RS- Serial... - utomationirect PLs RS-/RS irectlogi Universal Isolated Network dapter, p/n F-ISOON:... - irectlogi Universal onverter, p/n F-UNION:... - RS-/RS- Multi-rop Wiring iagram Examples... - llen-radley... - GE... - GE VersaMax Micro... - Mitsubishi... - Omron Modicon Modbus RS Modicon Micro Series... - Modicon Modbus with RJ... - Siemens... - hapter : Maintenance Project ackup... - heck Operating Environment... - heck Operating Voltage... - heck Status Indicators... - heck Physical onditions... - Run Tests under System Setup Screens... - heck Memory Usage... - heck/djust isplay rightness... - iv E-USER-M Hardware User Manual, st Ed. Rev. G

13 Table of ontents heck Error Log... - djust Touch Panel... - leaning the isplay Screen... - heck Project Functionality... - hecks from -more Programming Software... - Notes:... - hapter : Troubleshooting ommon Problems... - Troubleshooting Flow hart... - Touch Panel does not Power up... - isplay is lank... - isplay is im... - No User Program... - Firmware Recovery Tool... - No System Found... - No ommunications between Panel and P (Personal omputer) via US US river Troubleshooting... - No ommunications between Panel and P (Personal omputer) via Ethernet... - No ommunications between Panel and PL... - IP ddress in System Setup Screens displays ifficulty onnecting to the Panel over the Internet (Web server and Remote ccess features)... - PL Protocol Error odes... - Touch Panel Runtime Errors... - Panel onstantly isplays Initializing when Powering up... - ata not Logging Problems... - Electrical Noise Problems... - hapter : Replacement Parts Replacement Parts Overview... - Panel Mounting lip Replacements E-RK... - Logo Label Replacement Insert - E-LL wire ommunications Terminal lock E-T... - Panel Power onnector Replacement E--ON... - E-USER-M Hardware User Manual, st Ed. Rev. G v

14 Table of ontents Power dapter onnector Replacement E--ON... - Panel Gasket Replacements E-xx-GSK... - Gasket Replacement Installation Instructions:... - ppendix : Panel and PL Error ode Tables Introduction...- -more Touch Panel Error ode Table...- irectlogi Panel Error ode PL- Explanation...- irectlogi K-Sequence Protocol PL Error ode Table...- irectlogi irectnet Protocol PL Error odes...- Modbus Protocols Error ode P Explanation...- utomationirect LIK...- utomationirect irectlogi - Modbus (Koyo)...- Modicon Modbus RTU...- Entivity Modbus RTU...- irectlogi EOM Protocol PL Error odes...- Productivity Error ode P...- utomationirect o-more Error odes...- llen-radley Panel Error ode PL- Explanation...- llen-radley F & H Protocols PL Error ode Tables...-0 llen-radley EtherNet/IP Protocol Panel Error ode PL-, and Explanation...- llen-radley EtherNet/IP Protocol PL Error ode Tables ontrollogix, ompactlogix, & FlexLogix...- llen-radley EtherNet/IP Protocol PL Error ode Tables...- Generic EtherNet IP Protocol PL Error odes...- GE 0-0 Panel Error ode PL- Explanation...- GE 0-0 SNPX Protocol PL Error ode Tables...- Mitsubishi FX Protocol PL Error odes...- Omron Panel Error ode PL- Explanation...- Omron Host Link Protocol PL Error ode Table...- vi E-USER-M Hardware User Manual, st Ed. Rev. G

15 Table of ontents Omron FINS Protocol PL Error ode Table...- Omron Panel Error ode P Explanation...- Omron S/J FINS Ethernet Protocol PL Error ode Table...- Siemens Panel Error ode P Explanation...-0 Siemens PPI Protocol PL Error ode Table...- Siemens ISO over TP Protocol PL Error ode Table...- ppendix : Touch Panel Runtime Errors Introduction...- Runtime Errors...- Log File Naming... - ppendix : Security onsiderations for ontrol Systems Networks Security onsiderations for ontrol Systems Networks...- E-USER-M Hardware User Manual, st Ed. Rev. G vii

16

17 Getting Started hapter In This hapter... Introduction...- The Purpose of this Manual...- Supplemental Manuals...- Technical Support...- onventions Used...- Key Topics for Each hapter...- Product Overview...- Quick Start Steps...- Step Unpack and Inspect...- Step Install Optional Hardware ccessories...- Step ecome Familiar with vailable ommunication Ports...- Step Install the Programming Software and evelop a Project...- Step onnect Touch Panel to omputer...- Step Provide Power to the Touch Panel...-0 Step ccess the Touch Panel Setup Screens...- Step hoose Touch Panel to evice Protocol & ables...- Step onnect Touch Panel to PL...-

18 hapter - Getting Started 0 Introduction The Purpose of this Manual Thank you for purchasing our -more Touch Panel family of products. This manual describes utomationirect.com s -more Touch Panels, their specifications, included components, available accessories and provides you with important information for installation, connectivity and setup. The manual shows you how install, wire and use the products. It also helps you understand how to interface the panels to other devices in a control system. This user manual contains important information for personnel who will install the touch panels and accessories, and for the personnel who will be programming the panel. If you understand control systems that make use of operating interfaces such as the -more touch panels, our user manuals will provide all the information you need to get, and keep your system up and running. Supplemental Manuals If you are familiar with industrial control type devices, you may be able to get up and running with just the aide of the Quick Start Guide that is included with each touch panel. You can also refer to the On-line help that is available in the -more programming software for more information about programming the panel. Technical Support We strive to make our manuals the best in the industry. We rely on your feedback to let us know if we are reaching our goal. If you cannot find the solution to your particular application, or, if for any reason you need technical assistance, please call us at: 0 00 Our technical support group will work with you to answer your questions. They are available Monday through Friday from :00.M. to :00 P.M. Eastern Time. We also encourage you to visit our web site where you can find technical and non-technical information about our products and our company. - E-USER-M Hardware User Manual, st Ed. Rev. G

19 hapter - Getting Started onventions Used When you see the notepad icon in the left-hand margin, the paragraph to its immediate right will be a special note. The word NOTE: in boldface will mark the beginning of the text. When you see the exclamation mark icon in the left-hand margin, the paragraph to its immediate right will be a warning. This information could prevent injury, loss of property, or even death (in extreme cases). The word Warning: in boldface will mark the beginning of the text. Key Topics for Each hapter The beginning of each chapter will list the key topics that can be found in that chapter. Getting Started HPTER In This hapter... General Information...- Specifications E-USER-M Hardware User Manual, st Ed. Rev. G -

20 hapter - Getting Started 0 Product Overview Some of the features designed into the product to provide excellent hardware and software are listed below. nalog touch screen (no touch cell boundaries). The touchscreen is designed to respond to a single touch. If it is touched at multiple points at the same time, an unexpected object may be activated. Plenty of memory and methods to get data in/out of the panel Overlapping active devices on the touch screen, colors for enhanced graphics Screen resolutions up to 0 X pixel HMI Video Output on -inch and -inch models. uilt-in FTP client/server, client, and Web server udio output port - stereo, requires amplifier and speaker(s) (full feature units only) User configurable LE on the front of the panel uilt-in project simulation; test on P while developing Ethernet 0/00ase-T communications (not available on E-TL-R) pin serial port with RS-, RS/ -wire terminal block RS- port and RJ RS- port (full feature units only) Programming via US or Ethernet (Ethernet not available on E-TL-R) Optional / power adapter (E-) nimation of bitmaps and objects Thousands of built-in symbols and Windows fonts PI face plate, trending, alarming and a recipe database Event Manager to trigger actions based on assigned state changes, schedules, PL tag names, etc. setup in a database environment. The event can also trigger a sound byte, initiate a screen capture, send a data file (FTP), send an , etc. Trend ata logging Internet Remote ccess ustomizable label on the front of the panel - E-USER-M Hardware User Manual, st Ed. Rev. G

21 hapter - Getting Started Quick Start Steps Step Unpack and Inspect a.) Unpack the -more Touch Panel from its shipping carton. Included in the carton are the following: Quick Start Guide utout Template* -more Panel Gasket power connector Logo Label* -more Touch Panel cutout template mounting clips power connector gasket logo label Quick Start Guide *Not included with E-TL-R and E-TL. Shipping arton ontents Power dapter E- Mounting lips Optional ccessories US Pen rive US-FLSH b.) Unpack any accessories that have been ordered, such as: / Power dapter, programming cable, communications cable, etc. c.) Inspect all equipment for completeness. If anything is missing or damaged, immediately call the utomationirect returns Protective Screen over E-x-OV 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

22 hapter - Getting Started 0 Step Install Optional Hardware ccessories E- / Power dapter -more Touch Panel E-OMON- SU Port dapter US-FLSH US Pen rive E-x-OV Screen Protector E-S-R S ard - E-USER-M Hardware User Manual, st Ed. Rev. G

23 hapter - Getting Started Step ecome Familiar with vailable ommunication Ports Port Serial ommunication RS- Port RJ Serial ommunication RS- Pin Signal 0V N.. RX TX Supplies +V 0V Pin Signal Frame GN TX () RX () Logic GN + Logic Ground V (Supplies +V) Port PL Serial ommunications RS- / RS- Ethernet 0/00 ase-t PL ommunications, Programming/ownload Pin Signal Pin Signal T+ do not use T R R+ N.. do not use N.. Pin Signal Pin Signal LE (for H) TX+ (/) TS () TX (/) RTS () Term. Resistor RX+ (/) N.. Link Status LE (Green) On Ethernet Linked 0 RX (/) N.. Off No Ethernet omm. linking omm. ctivity Green Note: evice is not available on ase Feature touch panel E-TL-R Note: evice is not available on ase Feature touch panels E-TL-R and E-TL-R Note: evice is only available on touch panels E-TL and E-TL. Note: evice is only available on touch panels E-TL, E-TL and E-TL-R. Network Speed LE (Yellow) On 00M Off 0M S ard Slot S ard Slot Pin US Port - Type Programming Signal N.. + GN Shell Shield US Port - Type US evice Options Pin Signal Vbus + GN SHELL Shield HMI Port Video Out NOTE: See hapter : Specifications and hapter : PL ommunications for additional details on the available communication ports, protocols and cables. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

24 hapter - Getting Started 0 Step Install the Programming Software and evelop a Project Following are the minimum system requirements for running -more Programming Software, p/n E-PGMSW, on a P: Keyboard and Mouse or compatible pointing device Super VG color video adapter and monitor with at least 00 x 00 pixel resolution (0 x pixel recommended) K color minimum 00 M free hard-disk space -ROM or V drive for installing software from the US port or Ethernet 0/00 Mbps port for project transfer from software to touch panel (Ethernet port not available on E-TL-R) Operating System - Windows,,. and 0 ( or bit) Insert the supplied into the P s drive and follow the instructions. If you need assistance during the software installation, call the utomationirect Technical Support NOTES: Regarding Ethernet access to a -more panel. If you intend to take advantage of the methods of remote access to the panel, including the web server, P remote access, FTP, ios or ndroid app, you need to consider the security exposure in order to minimize the risks to your process and your -more panel. Security measures may include password protection, changing the ports exposed on your network, including a VPN in your network, and other methods. Security should always be carefully evaluated for each installation. Refer to ppendix - Security onsiderations for ontrol Systems Networks. - E-USER-M Hardware User Manual, st Ed. Rev. G

25 hapter - Getting Started Step onnect Touch Panel to omputer onnect a US Programming able, such as p/n US-L-, from a US type port on the P to the US type programming port on the -more touch panel or connect the -more touch panel and P together either directly or via an Ethernet switch, and T Ethernet cables (full feature panels only) P P P US Port Ethernet Port Ethernet Port US-L-xx US able Ethernet T able Ethernet T able US Port Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) -more Touch Panel -more Touch Panel uto MI / MI-X Ethernet Port -more Touch Panel uto MI / MI-X Ethernet Port 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

26 hapter - Getting Started 0 + GN Step Provide Power to the Touch Panel onnect a dedicated - V lass power supply to the connector on the rear of the -more touch panel, include wiring the ground terminal to a proper equipment ground - V Equipment Ground or install a -more / Power dapter, E-, to the rear of the touch panel and connect an voltage source of 00-0 V, 0/0Hertz, to its connector (see note below) then turn on the power source and check the LE status indicators on the front and rear of the -more touch panel for proper indication (see next page) NOTE: dedicated power supply is recommended. If the power supply also feeds inductive loads such as solenoids or relays, the transients caused by these loads can affect the operation of the panel or damage panel components. NOTE: The / Power dapter, E-, is for -more touch panels only. The adapter is powered from a 00-0 V, 0/0 Hertz power source. The adapter provides Power Fault features help protect data on an S memory card during power failures. Wiring Recommended Supply Fuse Panel Size Rating p/n 0 &..0 ML- ML -ON Tightening Torque Power connector screw torque 0. oz-in (0. Nm) Power connector mounting torque oz-in (0. Nm) Warning: Use 0 / copper conductors only. Wiring Recommended Supply Fuse.0 time delay, p/n: ML L 00-0 V 0 / 0 Hz Tightening Torque Power supply cable torque - oz-in ( Nm) Power connector mounting torque - oz-in ( Nm) Mounting flange screw torque - oz-in ( Nm) N G -0 E-USER-M Hardware User Manual, st Ed. Rev. G

27 hapter - Getting Started Step Provide Power to the Touch Panel (cont d) -more LE Status Indicators User efined LE (Green, Orange & Red) Off Green Red Orange linking Red linking Orange linking Green User efined (Refer to online help file for further details) PU Status LE (Green, Orange & Red) Off Green Power Off Normal PU Run State Red Memory Error linking Red Watchdog Timer Error linking Orange OS Error linking Green Power Loss etection Port Tx Rx Front View PU Rear View Port Tx Rx Power LE (Green) On Off Power On Power Off Tx/Rx LE (Green) RxSerial Port Tx On omm. is active Off No communication 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

28 hapter - Getting Started 0 Step ccess the Touch Panel Setup Screens ccess the Main Menu of the touch panel System Setup Screens by pressing the extreme upper left corner of the panel display area for three () seconds as shown below. djust the time and date for the panel by pressing the Setting button on the Main Menu, then press the djust lock button on the Setting screen. Use the right pointing arrows for the time or date display to select the unit to change. Use the up and down arrows to increment or decrement the value for the selected unit. Press OK when done to accept the changes to the time and date in the touch panel or press ancel to exit the djust lock setup screen without making any changes. Press the Main Menu button on the Setting screen and then the Exit button on the Main Menu screen to return to the application screen. - E-USER-M Hardware User Manual, st Ed. Rev. G

29 hapter - Getting Started Step hoose Touch Panel to evice Protocol & ables ompatibility Table Model Protocols Productivity Series Productivity Serial Productivity Ethernet o-more all o-more Serial o-more Ethernet LIK Modbus (LIK) K-Sequence L0/L0 all irect NET Modbus (Koyo addressing) H0-EOM/H0-EOM00 irect LOGI Ethernet L0 all K-Sequence -0 K-Sequence -0 K-Sequence irect NET L0-0/-0-/-0 K-Sequence irect NET Modbus (Koyo addressing) -0/-0-/-0 Using M irect NET Modbus (Koyo addressing) H-EOM/H-EOM00 irect LOGI Ethernet -0/0P (Requires the use of a ata ommunications Unit) irect NET utomationirect -0 irect NET K-Sequence L0-0 irect NET Modbus (Koyo addressing) -0 M irect NET Modbus (Koyo addressing) -0 K-Sequence irect NET -0 K-Sequence irect NET L0 K-Sequence -0 irect NET Modbus (Koyo addressing) ll with M irect NET Modbus (Koyo addressing) H-EOM/H-EOM00 irect LOGI Ethernet H-WinPL (Think & o) Live V. or later and Studio any version Think & o Modbus RTU (serial port) H-WinPL (Think & o) Live V.. or later and Studio V.. or later Think & o Modbus TP/IP (Ethernet port) GS rives GS rives Serial GS rives TP/IP (GS-ERV) SOLO Temperature ontrollers SOLO Temperature ontroller 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

30 hapter - Getting Started 0 Model Step hoose Touch Panel to evice Protocol & ables (cont d) llen-radley GE Mitsubishi Modicon Omron Siemens ompatibility Table (cont d) MicroLogix 000, 00, 00, 00, 00, SL -0/0/0 MicroLogix 000, 00, 00, 00 and 00 Protocols H/I/I+ SL -0/0/0 F Half uplex; F Full uplex ontrollogix, ompactlogix, FlexLogix PL- F Full uplex ontrollogix, ompactlogix, FlexLogix - Tag ased F Half uplex; F Full uplex ontrollogix, ompactlogix, FlexLogix - Generic I/O Messaging EtherNet/IP Server ontrollogix, ompactlogix, FlexLogix - Tag ased MicroLogix 00, 00 and SL /0, via native Ethernet port EtherNet/IP lient MicroLogix 000, 00, 00, 00, 00, SL -0/0/0, all via ENI adapter 0/0, 0/0. Micro 0, VersaMax Micro SNPX 0/0, Rxi SRTP Ethernet FX Series FX irect Q0, Q0H, Q0H, QH, QH Q PU Q, Qn Serial Qn Serial Q, Qn Ethernet Qn Ethernet PU, Quantum PU, EG Modicon Micro Series 0 PU: -xx, -xx, -xx, -xx Modbus RTU Modbus RTU Other devices using Modicon Modbus addressing TUModbus TP/IP 00 dapter, 00 Host Link J/S Serial FINS J/S Ethernet S-00 PU, RS- Serial PPI S-00 PU, S-00 PU, S-00 PU; Ethernet Ethernet ISO over TP - E-USER-M Hardware User Manual, st Ed. Rev. G

31 hapter - Getting Started Step hoose Touch Panel to evice Protocol & ables (cont d) vailable cables to connect from PL to -more serial Port Purchased able escription utomationirect Productivity Series, o-more, LIK, irect LOGI PL RJ- port, L0, L0, L0, L0, -0, -0 & H-WINPL (RS-) irect LOGI (VG Style) -pin port L0, -0 (0-), -0 (RS-) irect LOGI PL RJ- port, -0 (RS-) irect LOGI L0 PL -pin -sub port, L0 (RS-) irect LOGI PL -pin -sub port, L0, -0, L0 U and all M s (RS-) able Part Number E-L E-L- E-L E-L- E-L- llen-radley MicroLogix 000, 00, 00, 00, 00 (RS-) E-MLOGIX-L llen-radley SL -0/0/0, ontrollogix, ompactlogix, FlexLogix F port (RS-) llen-radley PL- F port (RS-) llen-radley SL -0/0/0, PL H port GE 0/0, 0/0, Micro 0, VersaMax Micro -pin -sub port (RS-) MITSUISHI FX Series -pin port (RS-) MITSUISHI FX Series -pin mini-in (RS-) OMRON Host Link (00 dapter, 00) (RS-) E-SL--L E-PL--L E-H-L E-0-0-L E-MITSU-L E-MITSU-L- E-OMRON-L NOTE: The above list of pre-made communications cables may be purchased. See hapter : PL ommunications for wiring diagrams of additional user constructed cables. hapter also includes wiring diagrams for the pre-made cables. Pre-made cable examples E-L E-L- 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

32 hapter - Getting Started Step onnect Touch Panel to PL 0 - onnect the serial communications cable between the -more touch panel and the PL or connect the -more touch panel and PL together either directly or via an Ethernet switch, and T Ethernet cables (full feature panels only) Serial -more Touch Panel L-0 PL E-L- Port Port Ethernet via Switch Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) H0-EOM/H0-EOM00 Ethernet Module Ethernet T able L0 PL -more Touch Panel uto MI / MI-X Ethernet Port Ethernet H0-EOM/H0-EOMM00 Ethernet Module L0 PL Ethernet T able -more Touch Panel uto MI / MI-X Ethernet Port E-USER-M Hardware User Manual, st Ed. Rev. G

33 Specifications hapter In This hapter... vailable Models...- Model Specifications...- Specifications common to all models...- -inch Models...- -inch Models...- -inch and 0-inch Models...- -inch and -inch Models...-0 E-TL-R, E-TL...- imensions, Inches [mm]...- Ports and Memory Expansion...- E-TL-R, E-TL...- imensions, Inches [mm]...- Ports and Memory Expansion...- E-TL...- imensions, Inches [mm]...- Ports and Memory Expansion...- E-T0L...- imensions, Inches [mm]...- E-T0WL...- imensions, Inches [mm]...- Ports and Memory Expansion...-

34 Specifications hapter E-TL...-0 imensions, Inches [mm]...-0 Ports and Memory Expansion...- E-TL-R, E-TL...- imensions, Inches [mm]...- Ports and Memory Expansion...- Mounting learances...- E-TL-R, E-TL erating...- ommunications Ports...- Handling External Memory evices...-0 Writing to External Memory evices...-0 Memory evice Formatting...-0 Minimizing ata Errors...- Monitoring vailable Memory...- File Name Limitations...- Power Loss Retention...- hemical ompatibility...-

35 This page intentionally left blank

36 hapter - Specifications 0 vailable Models Part Number E-TL-R E-TL E-TL-R E-TL E-TL E-T0L E-T0WL E-TL E-TL-R E-TL The -more Operator Interface is the next generation of touch panel brought to you by utomationirect. It has been designed to display and interchange graphical data from a PL by merely viewing or touching the screen. The -more Touch Panel is available in a variety of models to suit your application. Refer to the following tables for a list of part numbers, descriptions and options available. escription -more E series touch screen HMI, in color TFT L, 0 x 0 pixel, QVG, LE backlight, supports () serial and () US ports and () memory card slot. -more E series touch screen HMI, in color TFT L, 0 x 0 pixel, QVG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slot and () audio line out. -more E series touch screen HMI, in color TFT L, widescreen, 00 x 0 pixel, WVG, LE backlight, supports () serial, () Ethernet and () US ports and () memory card slot. -more E series touch screen HMI, in color TFT L, widescreen, 00 x 0 pixel, WVG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slot and () audio line out. -more E series touch screen HMI, in color TFT L, 00 x 00 pixel, SVG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slot and () audio line out. -more E series touch screen HMI, 0in color TFT L, 00 x 00 pixel, SVG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slot and () audio line out. -more E series touch screen HMI, 0in color TFT L, widescreen, 0 x 00 pixel, WSVG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slot and () audio line out. -more E series touch screen HMI, in color TFT L, 00 x 00 pixel, SVG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slots, () HMI video out and () audio line out. -more E series touch screen HMI, in color TFT L, 0 x pixel, XG, LE backlight, supports () serial, () Ethernet port and () US ports and () memory card slots. -more E series touch screen HMI, in color TFT L, 0 x pixel, XG, LE backlight, supports () serial, () Ethernet and () US ports, () memory card slots, () HMI video out and () audio line out. HMI Project S ard US Memory Option evice Ethernet Video Out M slot Yes No No M slot Yes Yes No M slot Yes Yes No M slot Yes Yes No M slot Yes Yes No M slot Yes Yes No M slot Yes Yes No M slots Yes Yes Yes M slots Yes Yes No M slots Yes Yes Yes - E-USER-M Hardware User Manual, st Ed. Rev. G

37 hapter - Specifications Model Specifications The following specification tables are separated into these groups: Specifications common to all models & Reduced and Full Feature Models, E-TL-R, E-TL, E-TL-R and E-TL & 0 Full Feature Models, E-TL, E-T0L and E-T0WL & Reduced and Full Feature Models, E-TL, E-TL-R and E-TL Specification tables begin on the next page. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

38 hapter - Specifications 0 Specifications common to all models Specification Operating Temperature ltitude Storage Temperature Humidity Environment Noise Immunity Model ll Models 0 to 0 ( to F); Maximum surrounding air temperature rating: 0 ( F) IE 00-- (Test Nb, Thermal Shock) Up to 000m ( ft) 0 to +0 ( to +0 F) IE 00-- (Test b, old) IE 00-- (Test b, ry Heat) IE 00-- (Test Na, Thermal Shock) % RH (non-condensing) For use in Pollution egree environment, no corrosive gases permitted (EN-) EN000-- (ES), EN000-- (RFI) EN000-- (FT) EN000-- (Serge) EN000-- (onducted) EN000-- (Power frequency magnetic field immunity) (Local Test) RFI, (MHz, 0Mhz 0cm) Impulse µs pulse Withstand Voltage 000 V, min. (FG to Power supply ) Insulation Resistance > 0M 00V (FG to Power supply ) Vibration Shock Emission Enclosure IE00-- (Test Fc) IE00-- (Test Ea) EN0 lass (Radiated RF emission) NEM 0 type /X indoor use only UL0 type X indoor use only IP- indoor use only (When mounted correctly) acklight verage Lifetime* 0,000 Touch Panel Type** Supply Power Four-wire analog resistive 0.-.V lass or SELV (Safety Extra-Low Voltage) ircuit or Limited Energy ircuit (LE) or use the / Power dapter, E-, to power the touch panel from a 00-0 V, 0/0 Hz power source. Reverse Polarity Protected * NOTE: The backlight average lifetime is defined as the average usage time it takes before the brightness becomes 0% of the initial brightness. The lifetime of the backlight depends on the ambient temperature. The lifetime will decrease under low or high temperature usage. ** NOTE: The Touchscreen is designed to respond to a single touch. If it is touched at multiple points at the same time, an unexpected object may be activated. - E-USER-M Hardware User Manual, st Ed. Rev. G

39 hapter - Specifications -inch Models Specification Model TFT color w/ base features TFT color w/ full features Part Number E-TL-R E-TL isplay ctual Size and Type isplay Viewing rea. TFT color. x.0 [. mm x. mm] Weight. lb (0g). lb (0g) Screen Pixel isplay rightness L Panel ot Pitch 0 x 0 (QVG) 0 nits (typ) 0. mm x 0. mm olor Scale, Project Memory Number of Screens Realtime lock alendar - Month / ay / Year Serial Port M Up to screens limited by project memory Realtime lock uilt into panel, backed up for 0 days at after power has been applied for hours Yes - monthly deviation 0 sec at -pin -sub female - RS, RS-/ Serial Port N/ -wire terminal block - RS- Serial Port N/ RJ- modular jack - RS- US Port - Type US Port - Type Ethernet Port udio Line Out Mic In (future) S ard Slot HMI Video Out Power onsumption Internal Fuse (non-replaceable) gency pprovals US.0 High speed (0 Mbps) Type - ownload/program US. and.0 High speed (0 Mbps) Type -for US device options N/ N/ N/ Ethernet Port Ethernet 0/00 ase-t, auto MI/MI-X. mm mini jack: -pin requires amplifier and speaker(s), Full Scale Output:.0 Vrms. mm mini jack: pin, Input: 00 mvrms, Impedance: <0kOhms slot. Supports max G (S,) max G (SH) V V UL0 (E), E (EN-), UL anadian., RoHS (0//EU) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

40 hapter - Specifications 0 -inch Models Specification Model TFT color w/ base features TFT color w/ full features Part Number E-TL-R E-TL isplay ctual Size and Type isplay Viewing rea.0 TFT color.0 x.0 [. mm x. mm] Weight. lb (0g). lb (0g) Screen Pixel isplay rightness L Panel ot Pitch 00 x 0 (WVG) 0 nits (typ) 0. mm x 0. mm olor Scale, Project Memory Number of Screens Realtime lock alendar - Month / ay / Year Serial Port M Up to screens limited by project memory Realtime lock uilt into panel, backed up for 0 days at after power has been applied for hours Yes - monthly deviation 0 sec at -pin -sub female - RS, RS-/ Serial Port N/ -wire terminal block - RS- Serial Port N/ RJ- modular jack - RS- US Port - Type US Port - Type Ethernet Port udio Line Out Mic In (future) S ard Slot HMI Video Out Power onsumption Internal Fuse (non-replaceable) gency pprovals US.0 High speed (0 Mbps) Type - ownload/program US. and.0 High speed (0 Mbps) Type -for US device options Ethernet Port Ethernet 0/00 ase-t, auto MI/MI-X N/ N/. mm mini jack: -pin requires amplifier and speaker(s), Full Scale Output:.0 Vrms. mm mini jack: pin, Input: 00 mvrms, Impedance: <0kOhms slot. Supports max G (S,) max G (SH) V V UL00 (E), E (EN-), UL anadian., RoHS (0//EU) - E-USER-M Hardware User Manual, st Ed. Rev. G

41 hapter - Specifications -inch and 0-inch Models Specification Model TFT color w/ full features 0 TFT color w/ full features 0 TFT color widescreen w/ full features Part Number E-TL E-T0L E-T0WL isplay ctual Size and Type. TFT color 0. TFT color 0. TFT color wide isplay Viewing rea. x.0 [0. mm x.mm]. x. [. mm x. mm]. x. [. mm x. mm] Weight. lb (0g). lb (00g). lb (00g) Screen Pixel 00 x 00 (SVG) 0 x 00 (WSVG) isplay rightness 0 nits (typ) 0 nits (typ) 0 nits (typ) L Panel ot Pitch 0. mm x 0. mm 0. mm x 0. mm 0. mm x 0.0 mm olor Scale Project Memory Number of Screens, colors M Up to screens limited by project memory Realtime lock Realtime lock uilt into panel, backed up for 0 days at alendar - Month / ay / Year Serial Port Serial Port Serial Port US Port - Type US Port - Type Ethernet Port udio Line Out Mic In (future) S ard Slot HMI Video Out Power onsumption Internal Fuse (non-replaceable) gency pprovals Yes - monthly deviation 0 sec (Reference) -pin -sub female - RS, RS-/ -wire terminal block - RS- RJ- modular jack - RS- US.0 High speed (0 Mbps) Type - ownload/program US.0 High speed (0 Mbps) Type -for US device options Ethernet Port Ethernet 0/00 ase-t, auto MI/MI-X. mm mini jack requires amplifier and speaker(s). mm mini jack slot. Supports max G (S,) max G V V V V UL0 (E), E (EN-), UL anadian., RoHS (0//EU) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

42 hapter - Specifications 0 -inch and -inch Models Specification Model TFT color w/ full features TFT color w/ base features TFT color w/ full features Part Number E-TL E-TL-R E-TL isplay ctual Size and Type. TFT color.0 TFT color isplay Viewing rea. x. [.0 mm x. mm]. x. [0. mm x.0 mm] Weight. lb (00g). lb (0g).0 lb (0g) Screen Pixel 00 x 00 (SVG) 0 x (XG) isplay rightness 0 nits (typ) L Panel ot Pitch 0.0 mm x 0.0 mm 0. mm x 0. mm olor Scale Project Memory Number of Screens, colors M Up to screens limited by project memory Realtime lock Realtime lock uilt into panel, backed up for 0 days at alendar - Month / ay / Year Serial PL Interface Port Yes - monthly deviation 0 sec (Reference) -pin -sub female - RS, RS-/ Serial PL Interface Port -wire terminal block - RS- N/ -wire terminal block - RS- Serial PL Interface Port RJ- modular jack - RS- N/ RJ- modular jack - RS- US Port - Type US Port - Type Ethernet Port udio Line Out US.0 High speed (0 Mbps) Type - ownload/program US.0 High speed (0 Mbps) Type -for US device options. mm mini jack requires amplifier and speaker(s) Ethernet Port Ethernet 0/00 ase-t, auto MI/MI-X N/. mm mini jack requires amplifier and speaker(s) Mic In (future). mm mini jack N/. mm mini jack S ard Slot slots. Supports max G (S), max G (SH) HMI Video Out HMI Type Port N/ HMI Type Port HMI Supported Resolution 00 x 00 (SVG) N/ 0 x (XG) Power onsumption Internal Fuse (non-replaceable) gency V V UL0 (E), E (EN-), UL anadian., RoHS (0//EU) -0 E-USER-M Hardware User Manual, st Ed. Rev. G

43 hapter - Specifications E-TL-R, E-TL imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the four mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template for marking the cutout dimensions on the mounting surface is provided in the box. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

44 hapter - Specifications 0 Ports and Memory Expansion E-TL-R E-TL - E-USER-M Hardware User Manual, st Ed. Rev. G

45 hapter - Specifications E-TL-R, E-TL imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the four mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template for marking the cutout dimensions on the mounting surface is provided in the box. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

46 hapter - Specifications 0 Ports and Memory Expansion E-TL-R E-TL - E-USER-M Hardware User Manual, st Ed. Rev. G

47 hapter - Specifications E-TL imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the four mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template for marking the cutout dimensions on the mounting surface is provided in the box. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

48 hapter - Specifications 0 Ports and Memory Expansion E-TL - E-USER-M Hardware User Manual, st Ed. Rev. G

49 hapter - Specifications E-T0L imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the eight mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template for marking the cutout dimensions on the mounting surface is provided in the box. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

50 hapter - Specifications 0 E-T0WL imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the eight mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template for marking the cutout dimensions on the mounting surface is provided in the box. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal - E-USER-M Hardware User Manual, st Ed. Rev. G

51 hapter - Specifications Ports and Memory Expansion E-T0L E-T0WL E-USER-M Hardware User Manual, st Ed. Rev. G - 0

52 hapter - Specifications 0 E-TL imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the eight mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template for marking the cutout dimensions on the mounting surface is provided in the box. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal -0 E-USER-M Hardware User Manual, st Ed. Rev. G

53 hapter - Specifications Ports and Memory Expansion E-TL E-USER-M Hardware User Manual, st Ed. Rev. G - 0

54 hapter - Specifications 0 E-TL-R, E-TL imensions, Inches [mm] ll the necessary mounting hardware is provided with the touch panel. Use the eight mounting clips and screws to secure the touch panel to the cabinet or enclosure surface. template is provided for marking the cutout dimensions on the mounting surface. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal - E-USER-M Hardware User Manual, st Ed. Rev. G

55 hapter - Specifications Ports and Memory Expansion E-TL-R E-USER-M Hardware User Manual, st Ed. Rev. G - 0

56 hapter - Specifications 0 E-TL - E-USER-M Hardware User Manual, st Ed. Rev. G

57 hapter - Specifications Mounting learances The following drawing shows the mounting clearances for the -more touch panel. There should be a minimum of inches of space between all sides of the panel and the nearest object or obstruction and at least. inches between the rear of the panel and the nearest object or obstruction. Min. Min. Min. Front View Min. Mounting lip. Min. ir Flow Side View 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

58 hapter - Specifications 0 E-TL-R, E-TL erating If E-TL-R and E-TL are mounted off the vertical plane facing upward, the temperature shall be derated as shown below. Other panels may be mounted at any angle without derating consideration. ngle: 0 to - Temp: 0 to ngle: 0 to - Temp: 0 to 0 0 ngle: - to -0 Temp: 0 to 0 ngle: - to 0 Temp: 0 to ngle: to 0 Temp: 0 to 0 E-TL-R, E-TL ngle: to 0 Temp: 0 to 0 ngle: 0 to Temp: 0 to E-TL-R, E-TL with E- 0 ngle: 0 to Temp: 0 to E-USER-M Hardware User Manual, st Ed. Rev. G

59 hapter - Specifications ommunications Ports Port Serial ommunication RS- Port RJ Serial ommunication RS- Pin Signal 0V N.. RX TX Supplies +V 0V Pin Signal Frame GN TX () RX () Logic GN + Logic Ground V (Supplies +V) Port PL Serial ommunications RS- / RS- Ethernet 0/00 ase-t PL ommunications, Programming/ownload Pin Signal Pin Signal T+ do not use T R R+ N.. do not use N.. Pin Signal Pin Signal LE (for H) TX+ (/) TS () TX (/) RTS () Term. Resistor RX+ (/) N.. Link Status LE (Green) On Ethernet Linked 0 RX (/) N.. Off No Ethernet omm. linking omm. ctivity Green Note: evice is not available on ase Feature touch panel E-TL-R Note: evice is not available on ase Feature touch panels E-TL-R and E-TL-R Note: evice is only available on touch panels E-TL and E-TL. Note: evice is only available on touch panels E-TL, E-TL and E-TL-R. Network Speed LE (Yellow) On 00M Off 0M S ard Slot S ard Slot Pin US Port - Type Programming Signal N.. + GN Shell Shield US Port - Type US evice Options Pin Signal Vbus + GN SHELL Shield HMI Port Video Out Ethernet Port The Ethernet port can be used several ways: for programming the panel (downloading a project), for PL communication, and for the advanced features, such as sending , web server, FTP access, and allowing users to access and control the panel remotely. The Ethernet connector is an RJ- Module jack. NOTE: E-TL-R does not include an Ethernet port and does not have these capabilities. Refer to for the latest driver information. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

60 hapter - Specifications 0 ommunications Ports (cont d) US Type Port Program -more via the US programming port. It s fast and easy, with no baud rate settings, parity, or stop bits to worry about. We stock standard US cables for your convenience, such as part no. US-L-. The US type port can be used to upload or download projects to and from a P (personnel computer). US Type Port The US type port is a standard feature for all models and can be used to connect various US.0 HI (Human Input evice) devices to the panel, such as: US pen drives, ( p/n US-FLSH) US keyboards US barcode scanners US card scanners -more can log data to the US pen drive as well as restore projects to the panel from the pen drive. You can also back up project files and panel firmware. Sound Interface (udio Line Out) When attached to an amplifier and speaker(s), -more can play warning sounds, or pre-recorded messages such as: conveyor is jammed. Various Objects in the -more programming software support sounds. -more supports WV type files. Sound files are stored in the sound library. udio WV File Specifications The -more udio Line Out port supports the following WV file specifications: udio Format (codec): PM udio Sample Rate:. khz hannels: (stereo) udio Sample Size: -bit - E-USER-M Hardware User Manual, st Ed. Rev. G

61 hapter - Specifications Serial ommunication Ports Port onnect to your serial controller network via Port. Port is a -pin port that supports RS- and RS-/. Port onnect your RS- network via Port. Port is provided with a -wire removable terminal block. Port onnect to your RS- device via Port. Port is an RJ connection NOTE: E-TL-R, E-TL-R and E-TL-R do not include Serial Ports and. HMI Port Video Out E-TL and E-TL include an HMI Type port to provide video output to a projector or monitor. Model Supported Resolution E-TL SVG 00 x 00 pixel E-TL XG 0 x pixel Output Sound Pass Through Video ata - Same Screen as Panel oes not support Mic sound Pass Through User efined LE The user defined LE on the panel front bezel can be controlled from the project to illuminate red, green or orange. It can also be configured to blink these colors. Refer to the online help file provided with the programming software for details. User efined LE (Green, Orange & Red) Off Green Red User efined Orange (Refer to online help file for further details) linking Red linking Orange linking Green Front View Power LE (Green) On Power On Off Power Off 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

62 hapter - Specifications 0 Handling External Memory evices Writing to External Memory evices ifferent types of numeric and text data from the -more touch panel can be stored on an S card or a US memory device. Numeric data from Line Trend Graph and PI Faceplate Trend Graph objects may be stored. Text data from Lookup Text and Multi-state Text objects can also be stored. Up to objects may be configured in the -more programming software to log data. long with the object limit, available storage on the external memory device is subject to the memory capacity of the S card or US memory device. One log file is created in a hour period for each object. dditionally logging data is initially stored in the buffer in the panel MRM and data is written to the external memory device: when k of data is cached, when 0 records have been stored, periodically, once every minute, when one of the SYS opy LogTo %device% or SYS %device% Eject tags is turned on. when there is an or FTP action when the System Screen is called when the panel date is changed Memory evice Formatting Memory evices should be formatted according to the following guidelines to insure best performance and integrity of logged data. Item apacity Supported Resolution Supported up to G FT Yes US Memory evice G to G FT Yes G or larger exft Yes Type S ard S up to G FT Yes SH G to G FT Yes SX exft No S cards must be formatted using the S formatter provided by the S ssociation at using the standard allocation unit size for best performance. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

63 hapter - Specifications Minimizing ata Errors To minimize data errors when logging data to external memory, consider the following: o not turn off power to the -more touch panel while the external memory device is being accessed. The optional E- power adaptor is designed to protect external memory devices from damage during power failure. o not remove any external memory device with the device is being accessed by the -more panel. The following internal tags should be used to monitor, access and safely remove external memory devices: SYS S WriteStatus SYS S WriteStatus SYS US WriteStatus SYS opy LogToS SYS opy LogToS SYS opy LogToUS SYS S Eject SYS S Eject SYS US Eject SYS S ReadyToUse SYS S ReadyToUse SYS US ReadyToUse e sure to backup the memory device at regular intervals. If you suspect the memory device is bad, you may want to use a P to re-format the device, or use a known good memory device. The number of times the memory device can be written to is limited. onsequently, logging frequently will may shorten the service life of the memory device. Using slower sample rates will increase the life of the device. Monitoring vailable Memory Each external memory device can be monitored and events can be configured to alert the user when available memory is approaching the maximum capacity of the external memory device. The following internal tags allow external memory devices data to be monitored: SYS S TotalMemory SYS S FreeMemory SYS S UsedMemory SYS S TotalMemory SYS S FreeMemory SYS S UsedMemory SYS US TotalMemory SYS US FreeMemory SYS US UsedMemory Refer to the -more programming software online help files for additional information on system tags and managing data logging devices. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

64 File Name Limitations There is a limit of file names with the same first four characters. Internal file names are restricted by the OS -character-dot--character limit. Therefore trend log files are identified internally by the first four characters of the object name plus tilde plus a three digit number. Examples are: TREN GRPH EST HILLER TEMP_0.txt is saved internally as TREN~00.txt TREN GRPH WEST HILLER TEMP_0.txt is saved internally as TREN~00.txt s new log files are created in each hour period, these files count against the maximum of files. If multiple graph objects appear on one screen, the files will be identified internally by the first Two haracters of the screen name plus the first Two haracters of the object name plus tilde plus three digit number. To maximize storage capabilities on external memory devices use screen names that have unique characters in the first four digits and object names that are unique in the first two characters. NOTE: When the filename limit is reached, the oldest files will automatically be deleted and logging will continue. Power Loss Retention When a power loss is detected, the panel will turn off the backlight immediately to extend the power retention period for completing data logging operations safely. The power retention period with -more E- Power dapter is long enough to complete writing to a properly formatted S ard but not the US. The power retention while using a power is not long enough to complete writes to an S ard or US device. n Uninterruptable Power Supply (UPS) should be considered. hemical ompatibility Power Loss etection (at ) Power Supply etect Loss (Panel only). V E- V ( - 0 inch) 0V ( - inch) The -more touch panels comprise three different materials that may be exposed to outside elements: a gasket, a screen sheet and a bezel. Gasket material is silicone. Screen sheets are PET. Panel bezels are S plastic.

65 ccessories hapter In This hapter... ccessories Overview... - / Power dapter... - / Power dapter imensions... - / Power dapter Installation SU -pin to Terminal lock dapters... - Non-glare Screen overs... - lear Screen Overlay Installation... - S ard US FLSH rive... -0

66 hapter - ccessories 0 ccessories Overview Part Number E- E--OV E--OV E--OV E-0-OV E-0W-OV E--OV E--OV E-S-R US-FLSH E-OMON- or E-OMON- E- / Power dapter -more Touch Panel E-OMON- or E-EOMON- SU Port dapter US-FLSH US Pen rive E-x-OV Screen Protector E-S-R S ard escription / dapter for -more E and E series touch panels; powered from a 00-0 V, 0/0 Hertz power source. Provides V at.. Power Fault features help protect data being logged to ompact Flash or S card during power failures. -more E series panels must have firmware version. uild.e or higher for proper operation. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series and -more Micro-Graphic -inch panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E series -inch panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series -inch panels. Package of. Non-glare protective overlay, 0-inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series 0-inch panels. Package of. Non-glare protective overlay, 0-inch widescreen, protects -more touch screen and helps reduce glare from external light sources. ompatible with E-T0WL panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series -inch panels. Package of. Non-glare protective overlay, -inch, protects -more touch screen and helps reduce glare from external light sources. ompatible with -more E and E series -inch panels. Package of. S memory card for non-volatile storage, G industrial grade. degrees maximum operating temperature makes it suitable for data logging in industrial applications. Recommended for the -more E series touch panels. US Flash drive, Sanisk, G (Sanisk P/N SZ0-0G-). Recommended for use with the -more touch panels and Productivity000 controllers. -SU -pin to -terminal PL serial communication port adapter to allow wire terminal connections for RS-/ PL communication cable. E-OMON- is low profile and fits E-TL-R, E-TL, E-TL and E-TL-R E-OMON- is straight and fits E-TL, E-T0L, E-TL and E-TL - E-USER-M Hardware User Manual, st Ed. Rev. G

67 hapter - ccessories / Power dapter The optional -more / Power dapter can be used to power the -more touch panels from a 00-0 V, 0/0 Hertz, voltage source. The adapter provides to the touch panel s power connector and can be conveniently secured to the touch panel with two captive screws. The adapter provides a power loss signal to the touch panel that causes the touch panel to stop writing data to S memory devices providing a controlled shutdown for increased data logging reliability. Part No. E- / dapter Wiring Recommended Supply Fuse.0 time delay, p/n ML 00-0 V 0/0 Hz Power dapter Not recommended for use with the E-T when operating temperatures are expected to be above 0 deg. Tightening Torque Power supply cable torque - oz-in ( Nm) Power connector mounting torque - oz-in ( Nm) Mounting flange screw torque - oz-in ( Nm) Warning: Use 0 / copper conductors only. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

68 hapter - ccessories 0 / Power dapter Specifications Part Number E- Input Voltage & frequency 00-0 V; 0/0 Hertz Operating Temperature Range 0 to 0 [ to F] Maximum surrounding temperature rating, 0 Storage Temperature Range -0 to 0 [- to 0 F] Operating & Storage Humidity 0-% RH (non-condensing) Noise Immunity 000 V p-p (Pulse width µs, rise time: ns) With proper ground connection on terminal block. Hi-pot 000 V, minute With proper ground connection on terminal block. Insulation Resistance 00 V, 0 M ohm or above With proper ground connection on terminal block. Vibration ompliant with IE- Shock Pulse shape: Sine half wave, Peak acceleration: m/s ( G), X, Y, Z: directions, times each Thermal Protection 0 [ F], with autorecovery Short ircuit Protection V:., 00 V:., V:. Static Electricity ischarge Resistance ompliant with IE000--, ontact: kv, ir: kv gency pprovals UL0, UL Recognized, cul, E, EM EN- Environment For use in pollution degree environment Grounding Ground resistance: less than 00 ohm Weight. oz. [ g] Removable Power onnector E--ON or E Switchlab M0-0-0G Secure with () captive M. screws, torque to 0 oz-in [0. Nm] Output urrent Maximum. Inrush urrent For 00 V:, ms or less For 0 V: 0, ms or less Recommended Supply Fuse.0 time delay, p/n ML Power Supply able Torque - oz-in ( Nm) Mounting to Touch Panel Secure with () spring loaded captive M-0 screws, torque to 0 oz-in [0. Nm] NOTE: Logic within the E- will turn off the backlight instantly when a power failure is detected to allow the PU to run longer. The backlight turns on automatically when the power returns to the -more operating voltage. - E-USER-M Hardware User Manual, st Ed. Rev. G

69 hapter - ccessories Screw / Power dapter imensions.00 [.] Power onnector. ±0.0 [. ± 0.] 0. [.]. [.0] Power Label imensions Power FRONT VIEW Screw SIE VIEW onnector RER VIEW OTTOM VIEW Units: inches [mm] Panel epth with / Power dapter Installed Units: inches[mm] Part Number E-TL-R. [.0] E-TL. [.0] E-TL-R. [.0] E-TL. [.0] E-TL. [.] E-T0L. [.] E-T0WL. [.] E-TL. [.] E-TL-R. [.] E-TL. [.] 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

70 hapter - ccessories 0 / Power dapter Installation WRNING: This procedure should only be performed by qualified personnel who are experienced in working with electronic equipment. Take the necessary steps to prevent damage that may be caused by static electricity discharge. isconnect input power to the touch panel before proceeding. Preparation: Place the touch panel face down on a lint-free soft surface to prevent scratching the display screen if not already installed in a control cabinet. Remove the power connector if it is installed. Secure the / Power dapter to the touch panel by tightening the two () spring loaded captive M-0 screws to a torque of 0 oz-in [0. Nm]. Insert the / power adapter into the touch panel s -position power connector. Plug the wired -pin Power onnector into its mating connector on the adapter and secure in place by tightening the two () captive M. screws to a torque of 0 oz-in [0. Nm]. - E-USER-M Hardware User Manual, st Ed. Rev. G

71 KOYO ELETRONIS INUSTRIES O., LT. hapter - ccessories -SU -pin to Terminal lock dapters These adapters are plugged into the -pin serial port on the rear of the panels to allow wire terminal connections for RS-/ PL communication cable. The wiring of both adapters is the same.. [.] E-OMON- is used with E-TL-R, E-TL, E-TL-R and E-TL. E-OMON- is UL Recognized. E-OMON- is NOT UL Recognized or Listed. It is used with E-TL, E-T0L, E-TL, E-TL-R and E-TL E-OMON- E-OMON- imensions. [.] Wiring iagram Units: inches [mm]. [.] Terminals GN S S+ R R+ TERM ate code ountry of Origin E-OMON- GN S S+ R R+ TERM 0. [.] -SU -pin to Terminal lock dapters (P/Ns E-OMON- & E-OMON-) GN S S+ R R+ TERM Wiring iagram imensions GN TX TX+ 0 RX RX+ TERM 0.0 [.] Units: inches [mm] -pin -sub (male).0 [.].0 [.] 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

72 hapter - ccessories 0 Non-glare Screen overs Non -glare PET screen covers are protective overlays used to protect the touch screen and help reduce glare from external light sources. (pk of ) Part No. E--OV, E--OV, E--OV, E-0-OV, E-0W-OV, E--OV & E--OV E-xx-OV Non-glare Screen overs imensions - inches [mm] Part Number E--OV. [.].0 [.] E--OV.0 [.].00 [0.] E--OV. [.]. [.] E-0-OV. [.]. [.0] 0. [.0] 0. [.0] E-0W-OV. [.]. [.] E--OV 0. [0.]. [.] E--OV. [.]. [.] - E-USER-M Hardware User Manual, st Ed. Rev. G

73 hapter - ccessories Non-glare Screen overs (cont d) lear Screen Overlay Installation Step heck to be sure that the proper size non-glare screen cover is being used on the subject touch panel. Notice that the outer perimeter of the screen cover has an adhesive band. The adhesive band will be located on the outside edge of the touch panel s white frame bordering the touch area when installed. Step lign the screen cover over the touch panel s white frame, then start on one side and gently lay the cover over the entire touch area. Step Remove the protective sheet. Step Start in one corner and peel the screen cover from the backing. Step Smooth out the screen cover and press all around the outside perimeter to secure the cover in place. The screen cover can be removed by lifting up on the small tab and gently pulling the cover away form the touch panel s surface. NOTE: The protective cover ships with a thin protective sheet on the face of the cover that needs to be carefully removed. If your panel is not clear, the protective sheet may not have been removed. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

74 hapter - ccessories 0 S ard S memory card for non-volatile storage, G industrial grade. maximum operating temperature makes it suitable for data logging in industrial applications. Recommended for the -more E series touch panels. The S card is the fastest option for writing data. If logged data is saved to external memory, utomationirect recommends using an E-S-R. US FLSH rive US-FLSH sold by utomationirect has been tested with -more panels and is Hi-Speed US.0 certified. Part No. US-FLSH -0 E-USER-M Hardware User Manual, st Ed. Rev. G

75 Installation and Wiring hapter In This hapter... Safety Guidelines...- Introduction...- E-TL-R, E-TL, E-TL-R and E-TL utout imensions...- E-TL and E-T0WL utout imensions...- E-TL utout imensions...- E-TL-R and E-TL utout imensions...- Mounting learances...- E-TL-R, E-TL erating...-0 Wiring Guidelines...- gency pprovals...- Providing Power to the Touch Panel...- -more LE Status Indicators...-

76 hapter - Installation and Wiring 0 Safety Guidelines NOTE: Products with E marks perform their required functions safely and adhere to relevant standards as specified by E directives provided they are used according to their intended purpose and that the instructions in this manual are adhered to. The protection provided by the equipment may be impaired if this equipment is used in a manner not specified in this manual. listing of our international affiliates is available on our Web site: automationdirect.com WRNING: Providing a safe operating environment for personnel and equipment is your responsibility and should be your primary goal during system planning and installation. utomation systems can fail and may result in situations that can cause serious injury to personnel or damage to equipment. o not rely on the automation system alone to provide a safe operating environment. You should use external electromechanical devices, such as relays or limit switches, that are independent of the PL application to provide protection for any part of the system that may cause personal injury or damage. Every automation application is different, so there may be special requirements for your particular application. Make sure you follow all national, state, and local government requirements for the proper installation and use of your equipment. Plan for Safety The best way to provide a safe operating environment is to make personnel and equipment safety part of the planning process. You should examine every aspect of the system to determine which areas are critical to operator or machine safety. If you are not familiar with control system installation practices, or your company does not have established installation guidelines, you should obtain additional information from the following sources. NEM The National Electrical Manufacturers ssociation, located in Washington,.. publishes many different documents that discuss standards for industrial control systems. You can order these publications directly from NEM. Some of these include: IS, General Standards for Industrial ontrol and Systems IS, Industrial Systems IS, Enclosures for Industrial ontrol Systems NE The National Electrical ode provides regulations concerning the installation and use of various types of electrical equipment. opies of the NE Handbook can often be obtained from your local electrical equipment distributor or your local library. Local and State gencies many local governments and state governments have additional requirements above and beyond those described in the NE Handbook. heck with your local Electrical Inspector or Fire Marshall office for information. - E-USER-M Hardware User Manual, st Ed. Rev. G

77 hapter - Installation and Wiring Introduction The installation and wiring of the -more touch panels requires selecting an appropriate location for the touch panel, laying out the cutout dimensions on the surface of the control cabinet that the panel will be mounted through, securing the touch panel with the provided mounting clips, tightening the screws to the appropriate torque rating to assure the gasket is sealing correctly, and finally connecting the appropriate power source to the touch panel. NOTE: Each -more touch panel is provided with a cutout template to make marking the proper cutout size on the surface of the control cabinet that the panel will be mounted through a simple task. This chapter covers the proper mounting of the touch panel and connecting power. Once power is applied to the touch panel, the user will want to read hapter on the System Setup Screens in order to set the internal time and date for the panel, become familiar with the touch panel test features, and check memory options. Mounting lips - E-RK 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

78 hapter - Installation and Wiring 0 E-TL-R, E-TL, E-TL-R and E-TL utout imensions The -more and touch panels are mounted into a cutout through the control cabinet and secured with four () mounting clips. The mounting clips are provided with the touch panel. The mounting clips will insert into a series of slots around the rear perimeter of the touch panel. Each clip has a tab that will mate to a slot. The screw of each mounting clip needs to be tightened to the torque rating shown in the table below so that the gasket is compressed to form the proper seal between the panel and cabinet surface. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal - E-USER-M Hardware User Manual, st Ed. Rev. G

79 hapter - Installation and Wiring E-TL and E-T0WL utout imensions The -more E-TL and E-T0WL touch panels will mount into the same cutout and are mounted into the cutout through the control cabinet and secured with four () mounting clips. The mounting clips are provided with the touch panel. The mounting clips will insert into a series of slots around the rear perimeter of the touch panel. Each clip has a tab that will mate to a slot. The screw of each mounting clip needs to be tightened to the torque rating shown in the table below so that the gasket is compressed to form the proper seal between the panel and cabinet surface. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

80 hapter - Installation and Wiring 0 E-T0L utout imensions The -more 0 touch panels are mounted into a cutout through the control cabinet and secured with eight () mounting clips. The mounting clips are provided with the touch panel. The mounting clips will insert into a series of slots around the rear perimeter of the touch panel. Each clip has a tab that will mate to a slot. The screw of each mounting clip needs to be tightened to the torque rating shown in the table below so that the gasket is compressed to form the proper seal between the panel and cabinet surface. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal - E-USER-M Hardware User Manual, st Ed. Rev. G

81 hapter - Installation and Wiring E-TL utout imensions The -more touch panels are mounted into a cutout through the control cabinet and secured with eight () mounting clips. The mounting clips are provided with the touch panel. The mounting clips will insert into a series of slots around the rear perimeter of the touch panel. Each clip has a tab that will mate to a slot. The screw of each mounting clip needs to be tightened to the torque rating shown in the table below so that the gasket is compressed to form the proper seal between the panel and cabinet surface. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

82 hapter - Installation and Wiring 0 E-TL-R and E-TL utout imensions The -more touch panels are mounted into a cutout through the control cabinet and secured with eight () mounting clips. The mounting clips are provided with the touch panel. The mounting clips will insert into a series of slots around the rear perimeter of the touch panel. Each clip has a tab that will mate to a slot. The screw of each mounting clip needs to be tightened to the torque rating shown in the table below so that the gasket is compressed to form the proper seal between the panel and cabinet surface. Enclosure Mounting Thickness Ranges and Mounting lip Screw Torque Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm] Mounting lip Screw Torque Material - oz-in [ Nm] Metal - 0 oz-in [ Nm] Metal - E-USER-M Hardware User Manual, st Ed. Rev. G

83 hapter - Installation and Wiring Mounting learances The following drawing shows the mounting clearances for the -more touch panel. There should be a minimum of inches of space between all sides of the panel and the nearest object or obstruction and at least. inches between the rear of the panel and the nearest object or obstruction. Min. Min. Min. Front View Min. Mounting lip. Min. ir Flow Side View 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

84 hapter - Installation and Wiring 0 E-TL-R, E-TL erating If E-TL-R and E-TL are mounted off the vertical plane facing upward, the temperature shall be derated as shown below. Other panels may be mounted at any angle without derating consideration. ngle: 0 to - Temp: 0 to ngle: 0 to - Temp: 0 to 0 0 ngle: - to -0 Temp: 0 to 0 ngle: - to 0 Temp: 0 to ngle: to 0 Temp: 0 to 0 E-TL-R, E-TL ngle: to 0 Temp: 0 to 0 ngle: 0 to Temp: 0 to E-TL-R, E-TL with E- 0 ngle: 0 to Temp: 0 to E-USER-M Hardware User Manual, st Ed. Rev. G

85 hapter - Installation and Wiring Wiring Guidelines WRNING: To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and it is your responsibility to determine which codes should be followed, and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes. Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation. If you have any questions concerning the installation or operation of this equipment, or if you need additional information, please call technical support at or This publication is based on information that was available at the time it was printed. t utomationdirect.com we constantly strive to improve our products and services, so we reserve the right to make changes to the products and/or publications at any time without notice and without obligation. This publication may also discuss features that may not be available in certain revisions of the product. gency pprovals Some applications require agency approvals for particular components. The -more touch panel agency approvals are listed below: UL (Underwriters Laboratories, Inc.) UL (anadian Underwriters Laboratories, Inc.) E (European Economic Union) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

86 hapter - Installation and Wiring 0 Wiring Guidelines (cont d) Providing Power to the Touch Panel onnect a dedicated - V lass power supply to the connector on the rear of the -more touch panel, include wiring the ground terminal to a proper equipment ground + GN - V Equipment Ground or install a -more / Power dapter, E-, to the rear of the touch panel and connect an voltage source of 00-0 V, 0/0Hertz, to its connector (see note below) then turn on the power source and check the LE status indicators on the front and rear of the -more touch panel for proper indication (see next page) NOTE: dedicated power supply is recommended. If the power supply also feeds inductive loads such as solenoids or relays, the transients caused by these loads can affect the operation of the panel or damage panel components. NOTE: The / Power dapter, E-, is for -more touch panels only. The adapter is powered from a 00-0 V, 0/0 Hertz power source. The adapter provides Power Fault features help protect data on an S memory card during power failures. Wiring Recommended Supply Fuse Panel Size Rating p/n 0 &..0 ML- ML -ON Tightening Torque Power connector screw torque 0. oz-in (0. Nm) Power connector mounting torque oz-in (0. Nm) Warning: Use 0 / copper conductors only. Wiring Recommended Supply Fuse.0 time delay, p/n: ML L 00-0 V 0 / 0 Hz Tightening Torque Power supply cable torque - oz-in ( Nm) Power connector mounting torque - oz-in ( Nm) Mounting flange screw torque - oz-in ( Nm) N G - E-USER-M Hardware User Manual, st Ed. Rev. G

87 hapter - Installation and Wiring -more LE Status Indicators User efined LE (Green, Orange & Red) Off Green Red Orange linking Red linking Orange linking Green User efined (Refer to online help file for further details) PU Status LE (Green, Orange & Red) Off Green Power Off Normal PU Run State Red Memory Error linking Red Watchdog Timer Error linking Orange OS Error linking Green Power Loss etection Port Tx Rx Front View PU Rear View Port Tx Rx Power LE (Green) On Off Power On Power Off Tx/Rx LE (Green) RxSerial Port Tx On omm. is active Off No communication 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

88

89 System Setup Screens hapter In This hapter... Introduction...- ccessing the System Setup Screens (no project loaded)...- ccessing the System Setup Screens (with project loaded)...- System Setup Screens Enable Password in Software...- System Setup Screens Flowchart...- Main Menu...- Information Menu...- Setting Menu...- Test Menu...- Memory Menu...-

90 hapter - System Setup Screens 0 Introduction The -more touch panels include a series of built-in System Setup Screens that allow the user to view detailed information about the panel; adjust certain features; configure communications; test various functions of the touch panel; backup & restore firmware, recipe, log and project memory; clear memory and reset all values and conditions back to the original factory defaults. The four Main Menu selections are: Information The information tabs display details about the touch panel model; the panel s name; version information for the hardware, boot loader and firmware; clock source, and beeper status. Other tabs display details on the panel s internal memory and the status of any external memory devices. ommunication port details are available in this area, as well as an error log to help in trouble-shooting the system Setting This is the area for.) making adjustments to the internal clock,.) adjusting the brightness of the display,.) setting the IP address.) adjusting (calibrating) the touch panel,.) enabling or disabling the internal beep, and.) enabling or disabling a mouse pointer. Test Menu From this sub menu, the user can.) test the touch panel,.) test the display,.) test the user LE.) test the communication ports, and.) test both the internal beeper or the audio line output, if a speaker with an amplifier is connected. WV sound file is system provided for the audio line output test. Memory Select the Memory menu item to either backup or restore your project, log data, recipe data and/or system memory. Selections can be made to backup to optional S card memory or US pen drive memory. The menu selections also give the user the ability to clear the memory, and there is also a selection to reset all of the touch panel settings back to the original factory defaults. - E-USER-M Hardware User Manual, st Ed. Rev. G

91 hapter - System Setup Screens ccessing the System Setup Screens (no project loaded) To access the Main Menu of the touch panel System Setup Screens prior to downloading a project, press the extreme upper left corner of the panel display area for seconds as shown below. The Main Menu will then be displayed. Press in the extreme upper left corner for seconds to bring up the System Setup Screen Main Menu. NO USER PROGRM 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

92 hapter - System Setup Screens 0 ccessing the System Setup Screens (with project loaded) To access the Main Menu of the touch panel System Setup Screens with a project loaded into memory, press the upper left corner of the panel display area for seconds as shown below. If no system screen password is enabled, the following WRNING dialog box will appear on the touch screen.: Pressing OK will display the system setup screen. See the WRNING below! System Screen alled Pressing ancel will take you back to the project screen. ctivating System Screen will stop the Panel Run Mode. o you want to continue? OK ancel ommunications with the PL is active while the Warning is displayed. The dialog box will close if no action is taken for 0 seconds. The dialog box will not display if the touch panel does not have a project loaded. The dialog box will display after a valid password is entered if the System Screen password is enabled. WRNING: Pressing OK at this point will STOP the PL driver and therefore all communications between the touch panel and PL will cease. It is strongly recommended that the password system tag SYS SYSTEMSREENPW be enabled to add a safeguard step in accessing the system setup screens. See the next section for an overview for setting the System Tags in the Event Manager atabase. - E-USER-M Hardware User Manual, st Ed. Rev. G

93 hapter - System Setup Screens System Setup Screens The OK button in the Warning dialog box will bring up the Main Menu as shown below. You can then proceed to the other system setup screens. Password Protecting System Screen ccess NOTE: If the password system tag SYS SYSTEMSREENPW is enabled, the Enter Security ode keypad shown below will open. The procedure to enable the SYS SYSTEMSREENPW is detailed below. Entering the correct password will display the Panel Run Mode warning dialog described previously. PL communications continue while the keypad is displayed. The keypad will timeout after 0 seconds. Enter Security ode 0 L Enter ancel 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

94 hapter - System Setup Screens 0 System Setup Screens Enable Password in Software Under the -more Programming Software s Navigation window, select the Function tab, then double click on larm ction to display the Event Manager atabase shown below: lick on the dd button to add an event to the database that will be used to enable the System Screen Password. - E-USER-M Hardware User Manual, st Ed. Rev. G

95 hapter - System Setup Screens System Setup Screens Enable Password (cont d) The Event dd dialog box will be displayed as shown. lick on the Tag Name: pull down menu and select the internal System it On (SYS IT ON) tag as shown. This will force the tag event type to be continuously active. Tag Name: SYS IT ON 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

96 hapter - System Setup Screens 0 System Setup Screens Enable Password (cont d) Use the Event Name: text box to document the event as System Screen PW for record keeping This is optional. In the ction box, click once on the displayed 0-larm under the Sequence List: so that 0-larm is highlighted. Then click the elete ction button to remove the 0-larm. Event Name: elete ction The Sequence List will now be cleared out. - E-USER-M Hardware User Manual, st Ed. Rev. G

97 hapter - System Setup Screens System Setup Screens Enable Password (cont d) In the ction box, click on the dd ction... button. This will bring up the dd ction dialog box as shown below: dd ction lick on the ommand: pull down list in the dd ommand box, select Tag from the list, then click OK. Tag 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

98 hapter - System Setup Screens 0 System Setup Screens Enable Password (cont d) 0-Tag action item will then be added to the Sequence List. 0-Tag lick on the Tag Name: pull down list down arrow in the ction box s Tag tab, select SYS SYSTEMSREENPW from the list, and click OK. 0 SYS SYSTEMSREENPW -0 E-USER-M Hardware User Manual, st Ed. Rev. G

99 hapter - System Setup Screens System Setup Screens Enable Password (cont d) Enter a numeric value into the Value: box, such as. This value becomes the Password code to access the System Setup Screen s Main Menu. Password Value lick the pply button in the Event dd dialog box and then the lose button to return to the Event Manager atabase. You now will see that the first event in the database is for the System Screen Password and it is enabled. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

100 0 hapter - System Setup Screens System Setup Screens Flowchart Main Menu Information Setting Test Menu Memory Touch Screen alibration (press upper left corner) General/Memory/Ethernet/ Error djust lock djust isplay IP ddress Setting djust Touch Panel (Touch Screen alibration) eep Mouse Test Touch Panel Test isplay Test User LE Test ommunication Port Test eep/sound ackup Restore lear Memory Reset to Factory efault - E-USER-M Hardware User Manual, st Ed. Rev. G

101 hapter - System Setup Screens Main Menu The Main Menu system setup screen is the top layer in the menu structure. Touch Screen alibration While the Main Menu system setup screen is being displayed, the extreme upper left corner of the touch panel can be pressed for seconds to access the Touch Screen alibration display. This feature is used if the touch panel data becomes corrupted and touching the Main Menu buttons does not work. It allows a shortcut to the touch panel calibration screen 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

102 hapter - System Setup Screens 0 Information Menu Information - General tab The General tab under the Information menu provides detailed information of the -more touch panel. Item No. Function escription omments Panel Type E-TL-R E-TL E-TL-R E-TL E-TL E-T0L E-T0WL E-TL E-TL-R E-TL Model Number Panel Name Version The panel name is configured in the programming software and saved with a project. The version identifications provide information on the components and firmware in the panel The default panel name is the model number plus the lower three bytes of the panel M address, ie E- TL-00. Files reside in the -more touch panel s memory. lock Internal/External clock selection. onfigured in the -more Programming Software. onfigurable in the Setting Menu eep Status of the internal beeper. eeper shown on page - or in the -more Programming Software. Main Menu Press to return to the Main Menu screen. Main Menu shown on previous page. - E-USER-M Hardware User Manual, st Ed. Rev. G

103 hapter - System Setup Screens Information - Memory tab. Memory components - Status of each memory component - SRM, MRM and uilt-in Flash are internal memory components. When external memory devices are installed in the panel they will be included in this list : S, S ( and inch panels only) and US.. Resource Monitor - this troubleshooting tool displays PU and panel internal memory usage. When enabled, the Resource Monitor will display on the panel screen WHILE THE PROJET IS RUNNING that is, after you click Main Menu then click Exit) - the Resource Monitor also allows access to the Error Tab WITHOUT STOPPING OMMUNITIONS WITH THE PL. Main Menu - Press to return to the Main Menu screen - Main Menu shown previously 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

104 hapter - System Setup Screens 0 Information - Ethernet tab Item No. Function escription omment Ethernet (Link: Online) Ethernet Settings: M ddress: 00 0 XX XX XX ddress Type: HP/Static IP ddress: Subnet Mask: efault Gateway: NS:.) utomatically.) Use esignated ddress Note: N/ - not available on reduced featured models ( R) Main Menu Press to return to the Main Menu screen. onfigurable in the Setting Menu IP ddress Setting shown on in this section or in the -more Programming Software. - E-USER-M Hardware User Manual, st Ed. Rev. G

105 hapter - System Setup Screens Information - Error tab Error Message Format: Error message format Navigation buttons Item No. Function escription omment Order of error message functions: Error Number, ate, Time, Error Port, evice Name, Error Type, PL evice, ccess ytes, Error Message ate Format: MM//YY ate error occurred. Time Format: HH/MM/SS Time error occurred. Error Port PL Serial ommunications Port: Ethernet: evice Name The name of the device reporting the error. evice names are configured in the programming software, Panel Manager Error Type R: Read WT: Write PL ddress The assigned address of the PL that caused the error. ccess ytes The number of access bytes. Error Message The error message is the same as the message displayed in the upper left of the -more touch panel s display. Error Message navigation buttons: list of Error Massages is shown in ppendix Item No. Function escription omment lear Page own Press to clear all error messages. This button is grayed out when there are no error messages to display. Press to go to to the next page. This button is grayed out when there is no error messages on the next page. Press to go to the previous page. This button Page Up is grayed out when there is no error messages on the previous page. Main Menu Press to return to the Main Menu screen. Errors are also cleared with firmware is updated on the panel. Errors are not cleared on power cycle or project transfer. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

106 hapter - System Setup Screens 0 Setting Menu The Setting Menu is used to adjust the time & date, adjust the contrast or brightness of the display, enter the IP address settings, adjust (calibrate) the touch screen, enable or disable the internal beep and turn on and off the mouse cursor. Item No. Function escription omments djust lock Press to go to the djust lock screen. djust isplay Press to go to the djust isplay screen. IP ddress Press to go to the IP ddress screen djust Touch Panel Press to go to the djust Touch Panel screen. eep Press to go to the eep screen. Mouse Press to go to the Mouse screen. Main Menu Press to return to the Main Menu screen. The IP ddress can also be set from the programming software or by the project. - E-USER-M Hardware User Manual, st Ed. Rev. G

107 hapter - System Setup Screens Setting djust lock Item No. Function escription omments Time: Each press of the Select button will cycle thru the following settings..) No Selection to Hours.) Hours to Minutes.) Minutes to Seconds Select.) Seconds back to Hours ate: Each press of the Select button will cycle thru the following settings..) Month to ay.) ay to Year.) Year back to Month Up own Press to increment the value by with each press. Press to decrement the value by with each press. OK Press to accept the changes. ancel Press to return to the Setting Menu screen without accepting the changes. NOTE: The function buttons used to adjust the clock settings on the panel s setup screen are disabled if an External clock source is selected in the -more programming software. The choice of an internal or external clock source is available by selecting lock Source in the -more programming software under the Main Menu drop down function Setup. NOTE: The panel s clock can also be adjusted from the -more programming software. The djust lock function can be accessed in the software by selecting djust lock under the Main Menu drop down function Panel or selecting djust lock under the Panel tab in the software s Navigation window. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

108 hapter - System Setup Screens 0 Setting djust isplay Item No. Function escription omments Setting olor Sample ontrast Sample Use the Up and own arrows to change the brightness. isplays a sample of how colors will appear with the new setting. isplays a sample of contrast with the new setting OK Press to accept the changes. ancel Press to return to the Setting Menu screen without accepting the changes. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

109 hapter - System Setup Screens Setting djust Touch Panel This procedure is used to calibrate the touch screen to ensure accuracy of the touch areas. There are five points on the touch screen that the calibration is based around. The adjustment relies on very narrow areas for the calibration points. NOTE: The panel will display the djust Touch Panel window on power up until the calibration procedure is completed. b Item No. Function escription omment c Start alibration Press to begin the touch screen calibration ancel Press to return to the Setting Menu screen. Points a thru e The touch screen calibration crosshairs will appear individually in the order of point a thru e respectively as each proceeding crosshair is pressed. a e d If the touched co-ordinate point is too far off from normal, then the procedure will return to Point a. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

110 hapter - System Setup Screens 0 Setting eep This system setup screen function is used to enable or disable the touch panel s internal beep function. Item No. Function escription omments Enable eep heck to enable the internal beep. OK Press to accept the changes. ancel Press to return to the Setting Menu screen without accepting the changes. NOTE: The project settings in the -more programming software Panel Manager will override the touch panel s internal setting upon initial download. - E-USER-M Hardware User Manual, st Ed. Rev. G

111 hapter - System Setup Screens Setting Mouse This system setup screen function is used to enable/ disable the arrow mouse cursor on the panel screen. It may be valuable to display the mouse cursor, for example, when an external US keyboard is connected to the panel.. NOTE: The project settings in the -more programming software Panel Manager will override the touch panel s internal setting upon initial download. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

112 hapter - System Setup Screens 0 Setting IP ddress Setting Item No. Function escription omment HP is enabled as the default when this system setup screen is first selected. HP ll of the other selections on this screen are dimmed when HP is selected and are not available. IP ddress IP ddress Subnet Mask efault Gateway Keypad OK ancel The Use the following IP ddress setting is selected when its radio button is pressed. Use the numerical keypad to assign the IP address. Select the field that needs to be assigned by touching the entry value and use the keypad to enter the desired address. The keypad is used to enter the ddress: Use the numeric keys to enter the address, e.g:..0. L = lear value entered Press to accept the changes and return to the Setting Menu screen. Press to return to the Setting Menu screen without accepting the changes. Note: If an Ethernet cable is not connected to the touch panel from an active Ethernet device, then the IP ddress will show as Each field can be independently assigned. NOTE: The project settings in the -more programming software Panel Manager will override the touch panel s internal setting upon initial download. - E-USER-M Hardware User Manual, st Ed. Rev. G

113 hapter - System Setup Screens Test Menu The Test Menu gives the user the ability to test the operation of the touch screen, test the L display, test the various communication ports, and also test the internal beeper and the audio line out through an user supplied amplified (stereo) speaker(s). Item No. Function escription omments Test Touch Panel Press to go to the Test Touch Panel screen. Test isplay Press to go to the Test isplay screen. Test User LE Test ommunication Port Tests the user configurable LE on the front of the panel. Refer to the online help file for details on the configuration of this LE. Press to go to the Test ommunication Port screen. Test eep/sound Press to go to the Test eep/sound screen. Main Menu Press to return to the Main Menu screen. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

114 hapter - System Setup Screens 0 Test Menu Test Touch Panel Using this test, normal or unusual operation of the analog touch panel can be determined. Testing: If an area of the touch screen is suspected to be inoperable, touch that area of the screen while in the Test Touch Panel screen mode. The screen pixels should turn black in that area. If the screen pixels do not turn black when touched, then the touch screen is defective or needs to be calibrated. See Setting - djust Touch Screen Item No. Function escription omments Touch area Touch to turn on pixels on the screen. oth the title bar (Test Touch Panel) and ancel button can be drawn across to test the touch operation. ancel Press to return to the Test Menu screen. NOTE: The Touchscreen is designed to respond to a single touch. If it is touched at multiple points at the same time, an unexpected object may be activated. - E-USER-M Hardware User Manual, st Ed. Rev. G

115 hapter - System Setup Screens Test Menu Test isplay There are two different test patterns that may be run on the display to allow the user to check for display screen defects. If the screen is not touched within seconds of Test Pattern being displayed, then Test Pattern will be displayed until the screen is touched, otherwise Test Pattern will remain until cancelled. Test Pattern displays a test pattern of grayscale graduations and RG colors. Test Pattern will follow the pattern as shown in the following chart with the color wiping across the screen in the direction indicated by the arrows, then repeats: olor st Time nd Time rd Time th Time RE GREEN LUE Item No. Function escription omments Touch the Test isplay screen. Press the screen anywhere except the ancel button and the shown Test Pattern remains. ancel (Test Pattern ) Press to return to the Test Menu screen. Touch nywhere Touch the sceen anywhere during Test (Test Pattern ) Pattern and return to the Test Menu screen. If the Test isplay screen is not touched, then in three seconds the display will move to Test Pattern. Test Results: If any pixels on the screen do not appear the same color as the surrounding pixels, the screen may be defective. single pixel gone bad is relatively common. Surrounding pixels going bad over time is another indication the screen may be defective. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

116 hapter - System Setup Screens 0 Test Menu Test ommunication Ports: Serial Ports The following test can be used to check the operation of the serial communication ports, with the use of a loop back connector and can also check the serial communications to any connected and configured PL. Item No. Function escription omments Loop ack Test PL Enquiry Test The loop back test checks the hardware components of the selected port for proper operation. This function allows the ability to select any PL that that may be connected to the touch panel via a serial connection and checks to see if the communications are working correctly. ancel Press to return to the Test Menu screen. Serial Port RS- Loop-back onnector Serial Port TX RX TS RTS -pin -sub (male) Wiring iagram RS- Loop-back onnector RX TX RJ (male) Wiring iagram The loop back test may be performed on Serial Port or Serial Port. Each tab shows diagrams to assist the user in building the loop back connector.. The PL must be configured for the selected port in the -more programming software Panel Manager and transferred tot he panel before attempting the PL Enquiry test. RS-/ Loop-back onnector TS RTS -pin -sub (male) RX+ TX+ 0 RX TX Wiring iagram - E-USER-M Hardware User Manual, st Ed. Rev. G

117 hapter - System Setup Screens ] Test Menu PL Serial omm Port Loop ack Test Test Results.) ytes Sent: The number of bytes sent after a test is started..) Receive ounts: The number of bytes which are received after the test is started..) Error ounts: The number of bytes which have not been received after the test is started..) RTS/TS Test: Pass/Fail RTS is turned on and if TS receives the signal then the test shows Pass, otherwise the test shows Fail. NOTE: The test will continue to run until the ancel button is pressed. If there are any error counts, check the loop back connector. If it is OK, call Tech Support.. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

118 hapter - System Setup Screens 0 Test Menu PL Enquiry Test: Serial onnection This function allows the ability to select any PL that may be connected to the touch panel through the selected serial comm. port connection and checks to see if the communications are working correctly. NOTE: The communications protocol for the PL being selected must be configured the same as the -more touch panel. The touch panel s PL serial communications are configured using the -more Programming Software s Panel Manager. PL Enquiry Test Four test packets are sent to the selected PL. The test result with return either Pass or Fail. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

119 hapter - System Setup Screens Test Menu Test ommunication Ports: Ethernet The following test feature can be used to check the operation of the Ethernet communication port by indicating if an Ethernet link has been established or not, and can also check the status of the Ethernet communications to any connected PL. ase featured models (-R) do not include an Ethernet port, therefore this check is not displayed. NOTE: The communications protocol for the PL being selected must be configured the same as the -more touch panel. The touch panel s PL serial communications are configured using the -more Programming Software s Panel Manager. Item No. Function escription omments Ethernet onnected This area displays information to whether an Ethernet link has been established for the touch panel s Ethernet comm port or not. isplays panel s IP address and shows whether it is static or assigned by a HP server. PL Enquiry Test This function allows the ability to select any PL configured in the project that may be connected to the touch panel via an Ethernet connection and checks to see if the communications are working correctly. ancel Press to return to the Test Menu screen. Example of displayed message when the touch panel s Ethernet port is not connected. Note that the address resets to even if it has previously been entered. L0 PL The PL must be configured for the selected port in the -more programming software Panel Manager and transferred to the panel before attempting the PL Enquiry test. Typical Ethernet connection with Ethernet switch. Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) H0-EOM/H0-EOM00 Ethernet Module Ethernet T able -more Touch Panel uto MI / MI-X Ethernet Port 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

120 hapter - System Setup Screens 0 Test Menu PL Enquiry Test: Ethernet onnection This function allows the ability to select any PL configured in the project that may be connected to the touch panel through an Ethernet port connection and checks to see if the communications are working correctly. NOTE: The communications protocol for the PL being selected must be configured the same as the -more touch panel. The touch panel s PL serial communications are configured using the -more Programming Software s Panel Manager. PL Enquiry Test Following are the steps that the Ethernet PL Enquiry Test performs:.) Ping the network times for the PL selected..) Four of the test read packets are sent to the selected PL. The test result will either be Pass or Fail. However, if the result of pinging the network shows an error, the test is stopped. - E-USER-M Hardware User Manual, st Ed. Rev. G

121 hapter - System Setup Screens Test Menu Test eep/sound The internal eeper can be tested from this system setup screen whether the eeper is enabled or disabled. fter the eep Test button is pressed and released, the eeper will sound for 00 msec. The Speaker Test function requires that a speaker(s) with an amplifier (can be stereo) be connected to the udio Line Out stereo jack on the rear of the touch panel. fter the Speaker Test button is pressed then released, a system provided Test.WV file will play once. WRNING: Hearing damage may occur if the volume on the user supplied external amplified speaker is set too high. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

122 hapter - System Setup Screens 0 Memory Menu The user s project, Firmware and OS, log and recipes files can be backed up to or restored from an S memory card (S ard Slot or S ard Slot ), or a US memory device. From this menu the user can also clear the project log files. The user also has the ability to clear the memory within the -more touch panel. Item No. Function escription omments ackup Restore lear Memory Reset to Factory efault ackup project, Firmware and OS, log & recipe files to the following memory devices: US port - Type : US pen drive S ard Slot (ll panels): S card S ard Slot (-inch & -inch): S ard Restore project, Firmware and OS, log & recipe files to the internal memory from one of the following memory devices: US port - Type : US pen drive S ard Slot (ll panels): S card S ard Slot (-inch & -inch): S ard lear selected data files from the memory of the following internal memory or external memory devices: uilt-in FLSH Memory US port - Type : US pen drive S ard Slot (ll panels): S card S ard Slot (-inch & -inch): S ard The touch panel s internal memory is set to the original factory defaults. Main Menu Press to return to the Main Menu screen. ny US.0 pen drive. S formats S and SH are supported. apacity up to G. The backup data files are created and copied to a folder on the memory device named E_Memory opy. The project file is named StartupStorage.eas Log and Recipe folders with the appropriate data files are also created on the memory device. folder on the memory device named E_Memory opy must exist containing a file named StartupStorage. eas. The project data file is stored in this file, and if the system data file was backed up, it also will be stored in this file. ny backed up log or recipe data files will be located under the appropriate Log or Recipe folders. an only clear project, log and recipe data files of the uilt-in FLSH memory. an clear entire contents or individual data files of external memory devices. lears all project memory. NOTE: The Project is RESTORE to the panel from an external memory device. project can be TRNSFERRE to and S card or US memory from the programming software to be RESTORE to a panel that is not connected to the programming software. This file has the.eas extension NOT the.eap extension of a projects SVE from the software. - E-USER-M Hardware User Manual, st Ed. Rev. G

123 hapter - System Setup Screens Project Executed from S ard Slot If the Project Storage/oot Location is set to uto or S in the -more software Panel Manager, and an S memory card is located in the S ard Slot at the time a project is transferred to the panel, the project will be stored on the S card, and the Internal Project Memory will be cleared. If Slot contains an S memory card with a project and the touch panel s power is cycled, then the project file stored on the S card is loaded into the touch panel s internal memory and executed. ny project in the internal FLSH memory is cleared. WRNING: uring power up with an S memory card plugged into an S card slot, do not remove the memory card from the slot. amage to the S memory card and possibly the touch panel may result. WRNING: fter a firmware update, the project files which are located in either the touch panel s internal FLSH memory or an S memory card plugged into an S card slot are cleared. The programming software will need to be used to Transfer the project file back into the panel. If you wish to retain the project on the S memory card, power down the panel and remove the S card before performing a firmware upgrade. Increasing Project Memory Size using an S memory card: If a project is transferred to the panel with an S memory card in S slot, the Font and Recipe data files are not included in the M (M for and models) project size. Therefore using an S memory card can allow a project to be loaded that is larger than M IF the excessive size is caused by Fonts and/or Recipe Sheets. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

124 hapter - System Setup Screens 0 Memory ackup The Memory - ackup selection allows you to backup the panel s Project, Log files, Recipe files or even the Firmware files to either an S memory card or US pen drive. The available memory devices will be displayed with their total and free memory. If the device is not available, it will be grayed out. The Next button is grayed out until a device is selected. The ancel button can be pressed at any time to return to the Memory Menu screen. This is an example of selecting a US memory device to write the backed up files to. The selected device is highlighted. Pressing again deselects it. Even if there is only one available memory device, it still needs to be highlighted in order to go to the next step. Press the Next button to continue to Step. Please read the explanation for the availability of S under different conditions that follow: - E-USER-M Hardware User Manual, st Ed. Rev. G

125 hapter - System Setup Screens Memory ackup (cont d) S ard Slot vailability Explanation: S may be unavailable (grayed out) if there is no card in S Slot or the card in S slot has the project currently running on the panel stored on it. The project will exist on S if the S card was installed in S when the project was TRNSFERRE to the panel by the -more programming software. If the panel is powered up or rebooted with an S card inserted into S Slot, then the S button s Total and Free memory will be displayed. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

126 hapter - System Setup Screens 0 Memory ackup (cont d) NOTE: The following definitions are for the various file types that can be backed up: Project data consists of the actual developed project data that is created in the -more programming software and includes all functionality, objects, screens, tag names, labels, comments, graphics, etc. Included in backup file name StartupStorage.eas. Recipe data consists of all the data values and labels that have been created for the various recipe sheets. Includes all recipe sheets loaded to the panel. Only recipe sheets used in the project are loaded to the panel. Firmware consists of the operating system, firmware and run time files. Included in backup file name StartupStorage.eas. Log data consists of the larm Log, Message Log and Trend ata Logging files. Select the data file(s) to be backed up by pressing the appropriate data file button. The selection will be highlighted. Pressing the highlighted data file button again will turn it off. The Next >> button will stay grayed out until at least one data file is selected. ny file type not available will be grayed out. The Next >> button is now enabled. Pressing ancel will return to the previous menu. Press the Next button to continue. NOTE: In the case of the Project and Firmware files, these can be Restored later to another panel. Recipe files can be edited externally from the panel and then Restored to the panel. The Log files are for viewing purposes only. See Memory - Restore later in this chapter for instructions on Restoring the Project, Firmware and or Recipe files to a Panel. - E-USER-M Hardware User Manual, st Ed. Rev. G

127 hapter - System Setup Screens Memory ackup (cont d) ackup ata Files Naming and Organization The following graphic shows how the various data files are organized on the memory device when doing a ackup and also the file naming convention that is used when viewed in Windows Explorer on a P. Folders Removable isk (F:) E_Memoryopy StartupStorage.eas ES File 0 K Log X larm_00.txt Text ocument K Screen.jpg 0 x 0 JPEG Image Recipe Steel.csv Microsoft Office Excel omma... K ackup memory device Project & Firmware backup file. Log backup files. Recipe Sheet backup files. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

128 hapter - System Setup Screens 0 Memory ackup (cont d) The next system setup screen allows the verification of the data file selections. When the OK button is pressed, the backup begins. The user can return to the previous screen by pressing the << Prev button. This message is displayed during the ackup copying process. Press the ancel button to abort the backup. The following text is shown in the copying progress message box: opy to US Memory: Please do not Power Off and Remove US opy to S or S: Please do not Power Off and Remove S WRNING: uring the copying process. o not power off the touch panel or remove the memory device. This message is displayed to indicate the ackup is complete. Press the OK button to return to the previous menu selection. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

129 hapter - System Setup Screens Memory ackup (cont d) Warning Messages If the destination does not have enough space to store the selected memory size, then the message shown here will be displayed. Press the OK button to clear the warning message. The warning message will read Not enough Memory Space in %evice%. %evice% will show either S, S, or US. This warning message will be displayed if the backup Memory device fails or is removed during the backup. Press the OK button to clear the warning message. The warning message will read ackup Failed. %evice% cannot be found. %evice% will show either S, S, or US. Refer to hapter : Troubleshooting for additional help. For any other reason the backup fails, then this warning message will be displayed. Press the OK button to clear the warning message. The warning message will read ackup Failed. Refer to hapter : Troubleshooting for additional help. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

130 hapter - System Setup Screens 0 Memory Restore The Memory - Restore function is used to:.) Restore a project previously backed up on an S card or US pen drive memory device to the same panel. See Memory - ackup previously in this chapter..) opy a project from one panel to another panel using a memory device to physically transport the data files..) Restore a project into the panel that was transfered to an External Memory evice using the -more Programming Software..) Restore Recipe Sheet(s) previously backed up to a memory device or copied to the memory device using a P. The available memory devices will be displayed showing the total and free available memory for that device. If the device is not available, it will be grayed out. The Next button is grayed out until a device is selected. The ancel button can be pressed at any time to return to the Memory Menu screen. This is an example of a US memory device selected to be the source for restoring the data file(s). The selected device is highlighted. Pressing again deselects it. Even if there is only one available memory device, it needs to be highlighted in order to go to the next step. Press the Next button to continue to continue to Step. NOTE: If you have a memory device inserted into the proper port on the touch panel, but it doesn t show up as highlighted in Step of the ackup setup screen, then try a different device to determine if the memory device is defective or if there is a possible problem with the memory device connection. It may not be compatible with the panel. Some US pen drives are not US.0 compatible and will not work with -more touch panels. Some US pen drives may take several minutes before they are recognized by the panel. S cards must be formatted using the S formatter provided by Scard.org - E-USER-M Hardware User Manual, st Ed. Rev. G

131 hapter - System Setup Screens Memory Restore (cont d) Please read the explanation for the availability of S under different conditions as shown on this page and the next. S vailability Explanation: S may be unavailable (grayed out) if there is no card in S Slot or the card in S slot has the project currently running on the panel stored on it. The project will exist on S if the S card was installed in S when the project was TRNSFERRE to the panel by the -more programming software. If the panel is powered up or rebooted with an S card inserted into S Slot, then the S button s Total and Free memory will be displayed. NOTE: The following definitions are for the various file types that can be restored: Project data consists of the actual developed project data that is created in the -more programming software and includes all functionality, objects, screens, tag names, labels, comments, graphics, etc. Included in backup file name StartupStorage.eas. Recipe data consists of all the data values and labels that have been created for the various recipe sheets. Includes all recipe sheets loaded to the panel. Only recipe sheets used in the project are loaded to the panel. Firmware consists of the operating system, firmware and run time files. Included in backup file name StartupStorage.eas. Log data consists of the larm Log, Message Log and Trend ata Logging files. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

132 hapter - System Setup Screens 0 Memory Restore (cont d) Restore Step : Select ata rea to Restore Project Total : K Log Total : K << Prev. Restore Recipe Total : K System Total : M Next >> Step : Select ata rea to Restore Project Total : K Log Total : K << Prev. Recipe Total : K System Total : M Next >> ancel ancel Select the data file(s) to be restored by pressing the appropriate data file button. The selection will be highlighted. The data file can be either the Project, Firmware and/or Recipe files. The selected data is restored to the internal built-in memory if there is no S card inserted into the S slot. Pressing the highlighted data file again will turn it off. The Next >> button will stay grayed out until at least one data file is selected. ny file type not available will be grayed out. This is an example of a file selected to restore. The selected file is highlighted. The Next >> button is now enabled. Pressing ancel will return to the previous menu. Press the Next button to continue. NOTE: The following definitions are for the various file types that can be restored: Project data consists of the actual developed project data that is created in the -more programming software and includes all functionality, objects, screens, tag names, labels, comments, graphics, etc. Included in backup file name StartupStorage.eas. Recipe data consists of all the data values and labels that have been created for the various recipe sheets. Includes all recipe sheets loaded to the panel. Only recipe sheets used in the project are loaded to the panel. Firmware consists of the operating system, firmware and run time files. Included in backup file name StartupStorage.eas. Log data consists of the larm Log, Message Log and Trend ata Logging files. - E-USER-M Hardware User Manual, st Ed. Rev. G

133 hapter - System Setup Screens Memory Restore (cont d) The data selected to restore is checked. If the data is good, then the OK button can be pressed to start the restore. If there is a problem with the data, the OK button will remain grayed out and the user can return to the previous screen by pressing the << Prev button. The problem could be caused by a corrupted data file. See hapter : Troubleshooting for additional help. This message is displayed during the Restore process. Press the ancel button to abort the backup. The following text is shown in the copying progress message box: opy to US Memory: Please do not Power Off and Remove US opy to S or S: Please do not Power Off and Remove S card WRNING: uring the copying process. o not power off the touch panel or remove the memory device. This message is displayed to indicate the Restore is complete. Press the OK button to return to the previous menu selection. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

134 hapter - System Setup Screens 0 Memory Restore (cont d) Warning Messages: If the system memory does not have enough space to restore the selected memory size, then the message shown here will be displayed. Press the OK button to clear the warning message. The warning message will read Not enough Memory Space in System Memory. The Project size must be less than 0 Myte for -0 panels and less than 0 Myte for & panels. This warning message will be displayed if the restore Memory device fails or is removed during the backup. Press the OK button to clear the warning message. The warning message will read Restore Failed. %evice% cannot be found. %evice% will show show S, S, or US. Try using a different device with known good data in the same connector or using the device that is causing the error in a different connector. For any other reason the restore fails, then this warning message will be displayed. Press the OK button to clear the warning message. - E-USER-M Hardware User Manual, st Ed. Rev. G

135 hapter - System Setup Screens Memory lear Memory This function is used to clear individually selected data files, or all data files, within the panel s uilt-in Memory, or any installed memory device such as a US pen drive or an S card. Select the memory device to clear. If the device is not available, it will be grayed out. The Next button is grayed out until a device is selected. The selected device is highlighted. Pressing again deselects it. When there are more than two available backup devices, the one selected will be highlighted. If another is selected, then the highlight will change to the last one pressed. Only one device can be selected at a time. Press the Next button to continue. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

136 hapter - System Setup Screens 0 Memory lear Memory (cont d) lear Memory Step : Select ata rea to Erase Project Total : 0 K Log Total : 0 K << Prev. Recipe Total : 0 K lear ll Total : 0 M Next >> ancel NOTE: Firmware files cannot be cleared from internal memory. lear Memory Step : Select ata rea to Erase Project Total : K Log Total : 0 K << Prev. Recipe Total : 0 K System Total : M Next >> ancel Select the data file(s) to be cleared. This is an example of an S card or US memory that was selected in lear Memory - Step-. The selected file will be highlighted. Pressing again deselects it. The Next >> button will stay grayed out until file(s) are selected. Selecting lear ll will erase all files located on the memory device. This is an example of US Memory that was selected in lear Memory - Step-. Notice the ability to select either the Project file, Log files, Recipe files, or the System files. This is an example of the Project data file being selected for clearing. The selected memory area is highlighted. Pressing again deselects it. The Next >> button is now enabled. Pressing ancel will deselect the file(s). Press the Next button to continue. - E-USER-M Hardware User Manual, st Ed. Rev. G

137 hapter - System Setup Screens Memory lear Memory (cont d) The data file(s)selected to clear are checked. If the data file is good, then the OK button can be pressed to start the clear procedure. If there is a problem with the data file, the OK button will remain grayed out and the user can return to the previous screen by pressing the << Prev button. Press the OK button to continue. This message is displayed during the clearing process. Press the ancel button to abort the clearing. The following text is shown in the clearing progress message box: learing uilt-in Memory: Please do not Power Off learing US Memory: Please do not Power Off or Remove US learing S or S Please do not Power Off or Remove S WRNING: uring the clearing process, do not power off the touch panel or remove the memory device. The following message is displayed when the clearing process is complete: %evice% cleared %evice% will show either S, S, or US. Press the OK button to return to the Memory Menu screen. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

138 hapter - System Setup Screens 0 Memory lear Memory (cont d) lear Memory Step : Select ata rea to Erase Project Total : 0 K Log Total : 0 K << Prev. Recipe Total : 0 K lear ll Total : 0 M Next >> ancel The following is an example of lear ll selected for clearing. The selected device is highlighted. The Next >> button is now enabled. Pressing ancel will deselect the lear ll. NOTE: If lear ll is selected, all files will be erased from the memory device, even those not related to the -more touch panel. The data file(s)selected to clear are verified. If the data file is good, then the OK button can be pressed to start the clear procedure. If there is a problem with the data file, the OK button will remain grayed out and the user can return to the previous screen by pressing the << Prev button. Press the OK button to continue. The warning message shown here will be displayed to give the user the opportunity to decide if they want to proceed or not. Press the OK button to continue. The lear ll process will start with a warning message as seen in the first example and continue until a message saying the device is cleared or a warning message as shown on the next page will appear. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

139 hapter - System Setup Screens Memory lear Memory (cont d) The warning message shown here will be displayed if the clearing process fails. lear Failed. Press the OK button to return to the lear Memory screen and try again. If the selected memory still fails to clear, then refer to hapter : Troubleshooting for additional help. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

140 hapter - System Setup Screens 0 Memory Reset to Factory efault fter pressing the Reset to Factory efault button from the Memory Menu, the message box shown will be displayed. Resetting to the Factory efaults produces the following actions:.) The touch screen calibration is reset to the Factory efaults..) The project file is cleared..) The log, recipe & WV files are cleared..) The IP address is set to HP. WRNING: s a precaution, it is recommended to create a backup file to an S card or US storage device using the Memory ackup function before resetting to factory defaults. ackup System Screen Memory Restore Reset to Factory efault was completed. lear Memory Reset to Factory efault OK Main Menu The message shown here is displayed once the Factory efault values have been stored into the system memory. Press OK to continue. fter pressing OK, the touch panel will reboot and startup on the Touch Screen alibration procedure as shown here. The following note is also shown on the calibration screens to remind the user that the Project File has been cleared, there s no communications with the PL, and the calibration procedure most be performed in order to ready the panel to download a project: Note: The panel will not communicate or run its project in this mode. lso, the -more Programming Software will not connect to the panel in this situation. - E-USER-M Hardware User Manual, st Ed. Rev. G

141 PL ommunications hapter In This hapter... Introduction...- irectlogi PLs Password Protection...- PL Protocol & ables...- PL ommunication ables & Wiring iagrams...- utomationirect PLs RS- Serial...- utomationirect PLs RS-/RS irectlogi Universal Isolated Network dapter, p/n F-ISOON:...- irectlogi Universal onverter, p/n F-UNION:...- RS-/RS- Multi-rop Wiring iagram Examples...- llen-radley...- GE...- GE VersaMax Micro...- Mitsubishi...- Omron...-0 Modicon Modbus RS-...- Modicon Micro Series...- Modicon Modbus with RJ...- Siemens...-

142 hapter - PL ommunications 0 Introduction The -more family of touch panels is capable of communicating with a wide variety of Programmable Logic ontrollers. -more is capable of communicating over RS, RS and RS serial networks as well as Ethernet networks. It communicates with all utomationirect PL s utilizing various protocols. -more also communicates with other brands of PLs by their different protocols. The table on the next page lists all of the various PLs and protocols that can be configured. The page after the protocol table lists the various serial communication cables that are available to purchase. The rest of this chapter is devoted to showing the pin to pin connections of all the available cables plus wiring diagrams that the user can refer to in order to construct their own cables, along with wiring diagrams of cables that are not available for purchase. To simplify RS/RS wiring schemes, we have included wiring diagrams showing connections for available terminal connectors such as our ZIPLink ommunication dapter Module, p/n ZL-M, used for example with our L-0 and -0 PLs. If you have difficulty determining whether the particular PL and/or protocol you are using will work with the -more series of touch panels, please contact our technical support group at irectlogi PLs Password Protection NOTE: Many irectlogic PLs support multi-level password protection of the ladder program. This allows password protection while not locking the communication port to an operator interface. The multilevel password can be invoked by creating a password with an upper case followed by seven numeric characters (e.g. ). Please refer to the specific PL user manual for further details. L-0 PL E-L- Port Port -more Touch Panel - E-USER-M Hardware User Manual, st Ed. Rev. G

143 hapter - PL ommunications PL Protocol & ables ompatibility Table Model Protocols Productivity Series Productivity Serial Productivity Ethernet o-more all o-more Serial o-more Ethernet LIK Modbus (LIK) K-Sequence L0/L0 all irect NET Modbus (Koyo addressing) H0-EOM/H0-EOM00 irect LOGI Ethernet L0 all K-Sequence -0 K-Sequence -0 K-Sequence irectnet L0-0/-0-/-0 K-Sequence irect NET Modbus (Koyo addressing) -0/-0-/-0 Using M irect NET Modbus (Koyo addressing) H-EOM/H-EOM00 irect LOGI Ethernet -0/0P (Requires the use of a ata ommunications Unit) irect NET utomationirect -0 irect NET K-Sequence L0-0 irect NET Modbus (Koyo addressing) -0 M irect NET Modbus (Koyo addressing) -0 K-Sequence irect NET -0 K-Sequence irect NET L0 K-Sequence -0 irect NET Modbus (Koyo addressing) ll with M irect NET Modbus (Koyo addressing) H-EOM/H-EOM00 irect LOGI Ethernet H-WinPL (Think & o) Live V. or later and Studio any version Think & o Modbus RTU (serial port) H-WinPL (Think & o) Live V.. or later and Studio V.. or later Think & o Modbus TP/IP (Ethernet port) GS rives GS rives Serial GS rives TP/IP (GS-ERV) SOLO Temperature ontrollers SOLO Temperature ontroller 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

144 hapter - PL ommunications 0 Model PL Protocol & ables (cont d) llen-radley GE Mitsubishi Modicon Omron Siemens ompatibility Table (cont d) MicroLogix 000, 00, 00, 00, 00, SL -0/0/0 MicroLogix 000, 00, 00, 00 and 00 Protocols H/I/I+ SL -0/0/0 F Half uplex; F Full uplex ontrollogix, ompactlogix, FlexLogix PL- F Full uplex ontrollogix, ompactlogix, FlexLogix - Tag ased F Half uplex; F Full uplex ontrollogix, ompactlogix, FlexLogix - Generic I/O Messaging EtherNet/IP Server ontrollogix, ompactlogix, FlexLogix - Tag ased MicroLogix 00, 00 and SL /0, via native Ethernet port EtherNet/IP lient MicroLogix 000, 00, 00, 00, 00, SL -0/0/0, all via ENI adapter 0/0, 0/0. Micro 0, VersaMax Micro SNPX 0/0, Rxi SRTP Ethernet FX Series FX irect Q0, Q0H, Q0H, QH, QH Q PU Q, Qn Serial Qn Serial Q, Qna Ethernet Qn Ethernet PU, Quantum PU, EG Modicon Micro Series 0 PU: -xx, -xx, -xx, -xx Modbus RTU Other devices using Modicon Modbus addressing Modbus RTU Modbus TP/IP 00 dapter, 00 Host Link J/S Serial J/S Ethernet FINS S-00 PU, RS- Serial PPI S-00 PU, S-00 PU; Ethernet Ethernet ISO over TP - E-USER-M Hardware User Manual, st Ed. Rev. G

145 hapter - PL ommunications PL ommunication ables & Wiring iagrams able escription able Part No. ables used with -pin RS-// serial Port utomationirect Productivity Series, o-more, LIK, irect LOGI PL RJ- port, L0, L0, L0, L0, -0, E-L -0 & H-WinPL (RS-) m (. ft) cable length irect LOGI (VG Style) -pin port, L0, -0 (0-), -0 (RS-) E-L- m (. ft) cable length irect LOGI PL RJ- port, -0 (RS-) m (. ft) cable length E-L irect LOGI L0 PL -pin -sub port, L0 (RS-) m (. ft) cable length E-L- irect LOGI PL -pin -sub port, L0, -0, L0 U and all M s (RS-) E-L- m (. ft) cable length llen-radley MicroLogix 000, 00, 00, 00 & 00 (RS-) E-MLOGIX-L m (. ft) cable length llen-radley SL -0/0/0, ontrollogix, ompactlogix, FlexLogix F port E-SL--L (RS-) llen-radley PL- F port (RS-) m (. ft) cable length E-PL--L llen-radley SL -0/0/0, PL H E-H-L port m (. ft) cable length GE 0/0, 0/0, Micro 0, Versamax Micro (Port) -pin -sub port (RS-) m (. ft) cable length MITSUISHI FX Series -pin port (RS-) m (. ft) cable length MITSUISHI FX Series -pin mini-in (RS-) m (. ft) cable length OMRON Host Link (00 dapter, 00) (RS-) m (. ft) cable length Port Pin E-0-0-L E-MITSU-L E-MITSU-L- E-OMRON-L -Sub -pin female on rear of touch panel 0V N.. RX TX +V 0V Port Signal able escription ables used with RJ RS- serial Port utomationirect Productivity Series, o-more, LIK, irect LOGI PL RJ- port, L0, L0, L0, L0, -0, -0 & H-WinPL (RS-).m (ft) cable length irect LOGI (VG Style) -pin port, L0, -0 (0-), -0 (RS-). Use with 0-L cable. irect LOGI PL -pin -sub port, L0 (RS-). Use with 0-L cable. irect LOGI PL RJ- port, -0 (RS-) m (. ft) cable length *Port + Logic Ground RJ RS- Serial ommunications able Part No. 0-L F-H F-KIT OP-L- RS- Serial ommunications *NOTE: ll cables for connections at Port are user constructed. Refer to the specifications of the connected device port to construct the cable properly. The connector for Port, E-T, is included with your -more panel. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

146 hapter - PL ommunications 0 ables from utomationirect (cont d) Part No. 0-L Part No. OP-L- Part No. F-H Part No. E-L Part No. E-L- Part No. F-KIT Part No. E-L- Part No. E-L- Part No. E-L Part No. E-MLOGIX-L Part No. E-SL--L Part No. E-PL--L Part No. E-H-L Part No. E-0-0-L Part No. E-MITSU-L Part No. E-MITSU-L- Part No. E-OMRON-L - E-USER-M Hardware User Manual, st Ed. Rev. G

147 hapter - PL ommunications PL ommunication ables & Wiring iagrams (cont d) The following series of wiring diagrams show the connectors and wiring details for the communication cables that are used between the -more touch panels and various PL controllers. Part numbers are included with the pre-made cables that can be purchased from utomationirect. The information presented will allow the user to construct their own cables if so desired. utomationirect PLs RS- Serial To PL RJ Port = Sig GN = do not use = RX = TX = do not use = do not use To PL -Pin H Port = do not use = Sig GN = do not use = TS = RTS = RX = TX = + V - N/ Productivity Series, o-more, LIK and irect Logic PL RJ port: L0, L0, L0, L0, L0, L0, H-WINPL RS- (p/n E-L) RJ -pin Phone Plug (P) TX RX GN Wiring iagram shield RX TX = do not use = do not use = do not use = Logic GN = do not use = RX () = TX () = Frame GN -pin -sub (male) E-L To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. E-L- irect Logic PL (VG style) -pin H port: -0, -0-, -0, L0 RS- (p/n E-L-) To -more -pin Port -pin Wiring iagram -pin H -sub -sub TX (male) RX = do not use = do not use (male) RX = do not use TX = do not use = do not use GN = donot use = do not use = Logic GN = do not use RTS = do not use 0 = do not use TS = RX () = do not use = TX () shield = Frame GN H = High ensity Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

148 hapter - PL ommunications 0 utomationirect PLs RS- Serial (cont d) To PL RJ Port irect Logic PL RJ port: -0 RS- (p/n E-L) = do not use = do not use = do not use = Logic GN = do not use = RX () = TX () = Frame GN E-L = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use TX RX RX TX GN shield Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. = RX = TX = do not use = Sig ground To PL -Pin Port = YOM Sense = TS = do not use = do not use = Online = RX () = TX () = YOP Sense RJ -pin Phone Plug (P) Wiring iagram irect Logic PL -pin -sub port: L0, RS- (p/n E-L-) Wiring iagram -pin -sub (male) To -more -pin Port E-L- To -more -pin Port TX RX -pin -pin RX TX -sub -sub online (male) = Logic GN = do not used (male) = Logic GN = do not used = Logic GN GN = do not used = do not use GN = Logic GN = do not use = do not used GN 0 = do not use = RX () = do not use YOP = TX () TS = Frame GN See PL user manual YOM for pin out details. shield Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use - E-USER-M Hardware User Manual, st Ed. Rev. G

149 hapter - PL ommunications utomationirect PLs RS- Serial (cont d) To PL -Pin Port -pin -sub (male) irect Logic PL -pin -sub port: L0, -0, L0 U, and all Ms, RS- (p/n E-L-) Wiring iagram E-L- -pin -sub (male) To -more -pin Port = do not use = do not use TX RX = do not use = do not use = do not use RX = do not use = do not use = do not use TX = do not use 0 = do not use = do not use GN = do not use = Logic GN = do not use = do not use RTS = do not use = Signal GN 0 = do not use = RX () = do not use = do not use TS = TX () = TS = do not use = Frame GN = RTS = do not use shield = RX = do not use = TX = do not use = do not use = do not use Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. RJ -pin Phone Plug (P) = Sig GN = not used = RX = TX = not used = not used To PL RJ Port = RX = TX = do not use = Sig GN RJ -pin Phone Plug (P) RJ -pin Phone Plug (P) GN RX TX 0-L RS- RJ to RJ Shielded able feet [. m] Wiring iagram GN RX TX irect Logic PL RJ port: -0 Port & RS- (p/n OP-L-) RX TX GN Wiring iagram TX RX RJ -pin Phone Plug (P) RJ -pin Phone Plug (P) = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use 0-L RJ -pin Phone Plug (P) = Sig GN = not used = RX = TX = not used = not used OP-L- Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. To -more E series Serial Port = Sig GN = not used = RX = TX = + V = Sig GN 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

150 hapter - PL ommunications 0 utomationirect PLs RS-/RS- When using the RS-/RS- capabilities of the -more -pin PL communications Port, the termination resistor is placed between the RX and RX+ terminals on the PL side of the connection between the touch panel and PL. The Termination Resistor value is based on the characteristic impedance of the cable being used. To enable the built-in 0 Ohm Termination Resistor, jumper pin to pin (RX+) on the -more -pin PL communications Port. User onstructed To PL -Pin Port irect LOGI L-0, -0, -0-, -0 (all Port ) RS- To -more -pin Port Wiring iagram -pin Term. -pin H -sub -sub TX+ (male) R+ = do not use (male) = do not use TX 0 0 R = do not use = do not use = do not use RX+ = do not use S+ = Termination = Sig GN = TS = Logic GN = S (RS) = RX = TS+ RX S = do not use = S+ (RS) = do not use = RX+ GN = do not use 0 = R (RS) = do not use = RTS- = do not use = R+ (RS) = do not use = RTS+ RTS = Frame GN = do not use 0 = TX TS = do not use = TX+ RTS+ TS+ shield Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. To PL -Pin Port irect LOGI -M*, -M* & -M* RS- User onstructed To -more -pin Port -pin Wiring iagram -sub = do not use Term. -pin (male) = do not use -sub = TS TX+ R+ = TS+ = do not use = do not use (male) = do not use = RTS = do not use TX 0 R = do not use = do not use 0 = RTS+ = do not use RX+ = do not use S+ = Termination = do not use 0 = do not use = Logic GN = S (RS) = do not use = do not use RX S = do not use = S+ (RS) = 0 V = do not use = do not use 0V = do not use 0 = R (RS) = do not use = RX+ = do not use = R+ (RS) = do not use (RS) RTS = Frame GN = do not use = RX TS = do not use (RS) RTS+ 0 = do not use = TX * Note: The M modules must be set for: (RS) TS+ irect NET Slave, HEX mode. = TX+ shield (RS) Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. NOTE: The RS- wiring diagrams shown above are not for multi-drop networks involving connecting more than one PL to a panel. Refer to the multi-drop wiring diagram examples later in this chapter if more than one PL will be connected to a panel. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

151 hapter - PL ommunications utomationirect PLs RS-/RS- (cont d) To PL -Pin Port = do not use = do not use = TS+ 0 = RX (RS) = RX+ (RS) = do not use = 0 V = do not use = do not use = do not use = do not use = do not use = do not use To PL -Pin Port = TX (RS) = TX+ (RS) = do not use 0 = do not use = do not use = do not use = 0 V = do not use = do not use = do not use = do not use = do not use = do not use -pin -sub (male) irect LOGI -0/-0/-0 Port and -0 Port RS- = do not use = do not use = TS = do not use = do not use 0 = do not use = RTS+ = RTS = do not use = TX (RS) = do not use = TX+ (RS) TX+ TX RX+ RX 0V RTS TS RTS+ TS+ 0 Wiring iagram shield User onstructed Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. -pin -sub (male) = RX (RS) = RX+ (RS) = do not use = do not use = do not use 0 = do not use = do not use = do not use = do not use = do not use = do not use = do not use TX+ TX RX+ RX 0V 0 irect LOGI -0 Port RS- RTS and TS are not present on this port. Wiring iagram shield Term. R+ = do not use R = do not use = do not use S+ = Logic GN S = do not use = do not use = do not use = Frame GN -pin -sub (male) To -more -pin Port = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) User onstructed Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. 0 Term. R+ = do not use R = do not use = do not use S+ = Logic GN S = do not use = do not use = do not use = Frame GN -pin -sub (male) To -more -pin Port = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) NOTE: The RS- wiring diagrams shown above are not for multi-drop networks involving connecting more than one PL to a panel. Refer to the multi-drop wiring diagram examples later in this chapter if more than one PL will be connected to a panel. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

152 hapter - PL ommunications 0 utomationirect PLs RS-/RS- (cont d) To PL -Pin Port = do not use = Sig GN = RX = do not use = do not use = do not use = do not use = do not use -pin H -sub (male) = TS = TS+ = RX+ = RTS- = RTS+ 0 = TX = TX+ irect LOGI L-0, -0 (both Port ) RS- RX+ TX+ TX RX GN RTS TS RTS+ TS+ 0 Wiring iagram shield User onstructed Note: Use the above wiring diagram to make your own cable. We recommend elden shielded cable or equivalent. 0 Term. R+ = do not use S+ = do not use = do not use R = Logic GN S = do not use = do not use = do not use = Frame GN -pin -sub (male) To -more -pin Port = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) NOTE: The RS- wiring diagram shown above is not for multi-drop networks involving connecting more than one PL to a panel. Refer to the multi-drop wiring diagram examples later in this chapter if more than one PL will be connected to a panel. - E-USER-M Hardware User Manual, st Ed. Rev. G

153 hapter - PL ommunications utomationirect PLs RS-/RS- (cont d) User onstructed irect LOGI ZIPLink ZL-ML dapter Module to E-OMON- Terminal lock dapter RS- PL -0 or L0 only Port RS/ TERMINTE ZL-ML RX TX ZL-ML RS- RX RS- TX +V SIGNL GN RS-/ RX RS-/ TX RS-/ RX+ RS-/ TX+ Wiring iagram shield See ZL-ML specifications on termination resistor jumper. GN R S S+ R+ TERM Terminal lock dapter plugs into -more -pin Port *E-OMON- Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. TERMINTE TX+ RX+ TX- RX- SG +V TX RX TX+ RX+ TX- RX- SG +V TX RX ZL-ML RS- RX RS- TX +V SIGNL GN RS-/ RX RS-/ RX+ RS-/ TX RS-/ TX+ Wiring iagram shield See ZL-ML specifications on termination resistor jumper. User onstructed irect LOGI ZIPLink ZL-ML dapter Module to E-OMON- Terminal lock dapter RS- PL -0 (-), -0 or L0 Port Terminal lock dapter RS/ ZL-ML RX TX GN S S+ R R+ TERM plugs into -more -pin Port *E-OMON- Note: Use the above wiring diagram to make your own cable. We recommend elden shielded cable or equivalent. NOTE: The RS- and RS- wiring diagrams shown above are not for multi-drop networks involving connecting more than one PL to a panel. Refer to the multi-drop wiring diagram examples later in this chapter if more than one PL will be connected to a panel. * NOTE: E-OMON- will install only on E-TL, E-TL-R, E-TL and E-TL-R panels 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

154 hapter - PL ommunications 0 utomationirect PLs RS-/RS- (cont d) Wiring iagram User onstructed Productivity PL RS Port to E-OMON- Terminal lock dapter Terminal lock dapter plugs into -more -pin Port SIGNL GN GN TX / RX TX / RX + * R S Productivity S + PS Port R + shield TERM * 0 Ω resistor *E-OMON- Note: Use the above wiring diagram to make your own cable. We recommend elden shielded cable or equivalent. Removable onnector included with Productivity PU TX+ / RX+ TX- / RX- Ground + - G utomationirect Productivity PL RS- Wiring iagram TX+ / RX+ Term. TX- / RX- 0 Ground shield User onstructed Term. R+ = do not use S+ = do not use = do not use R = Logic GN S = do not use = do not use = do not use = Frame GN -pin -sub (male) = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) Note: Use the above wiring diagram to make your own cable. We recommend elden shielded cable or equivalent. Use 0 ohm resistors as termination resistors (Term.) To -more -pin Port NOTE: The RS- and RS- wiring diagrams shown above are not for multi-drop networks involving connecting more than one PL to a panel. Refer to the multi-drop wiring diagram examples later in this chapter if more than one PL will be connected to a panel. * NOTE: E-OMON- will install only on E-TL, E-TL-R, E-TL and E-TL-R panels - E-USER-M Hardware User Manual, st Ed. Rev. G

155 hapter - PL ommunications utomationirect PLs RS-/RS- (cont d) LIK om Port RS- Signal RS- Signal Logic Ground + - LG RS- Signal RS- Signal Logic Ground utomationirect LIK PL nalog PU RS- Wiring iagram Term. 0 shield User onstructed Note: Use the above wiring diagram to make your own cable. We recommend elden shielded cable or equivalent. Use 0 ohm resistors as termination resistors (Term.) Term. R+ = do not use S+ = do not use = do not use R = Logic GN S = do not use = do not use = do not use = Frame GN -pin -sub (male) To -more -pin Port = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) NOTE: The RS- wiring diagram shown above is not for multi-drop networks involving connecting more than one PL to a panel. Refer to the multi-drop wiring diagram examples later in this chapter if more than one PL will be connected to a panel. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

156 hapter - PL ommunications 0 irectlogi Universal Isolated Network dapter, p/n F-ISOON: Modular cable included with the F-ISOON F-ISOON Universal Isolated Network dapter RS- to RS- PL L0 or -0 Port only RX TX TX EN TX RX TS - +V - TX+ TX RX RX+ - F-ISOON OM RX RX+ TX TX+ Wiring iagram shield Ground the shield only at the equipment end where the F-ISOON is located. See F-ISOON specificaitons to properly configure the adapter. GN S S+ R R+ TERM Terminal lock dapter plugs into -more -pin Port *E-OMON- Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. PWR RUN PU RX RX TX TX Port Note: When using multiple PLs connected to one -more touch panel, only jumper the Term terminal to the R+ terminal when the panel is the last device at one end of the network. L0 PL ** NOTE: E-OMON- will install only on E-TL, E-TL-R, E-TL and E-TL-R panels - E-USER-M Hardware User Manual, st Ed. Rev. G

157 hapter - PL ommunications irectlogi Universal onverter, p/n F-UNION: F-UNION F-UNION Universal onverter RS- to RS- PL L0 or -0 Port only GN RX RX+ TX TX+ See F-UNION specificaitons to properly configure the converter. Modular cable included with the F-UNION Wiring iagram shield Ground the shield only at the equipment end where the F-UNION is located. Note: When using multiple PLs connected to one -more touch panel, only jumper the Term terminal to the R+ terminal when the panel is the last device at one end of the network. -0 PL GN S S+ R R+ TERM Terminal lock dapter plugs into -more -pin Port *E-OMON- Note: Use the above wiring diagram to make your own cable. We recommend elden 0 shielded cable or equivalent. PWR TT L0 PU * NOTE: E-OMON- will install only on E-TL, E-TL-R, E-TL and E-TL-R panels RUN PU RUN TERM H H H H PORT PORT 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

158 RX TX RS/ SG RS/ RX TX SG hapter - PL ommunications 0 GN RS-/RS- Multi-rop Wiring iagram Examples TX TX+ RX RX+ RTS+ TS+ RTS TS L0 and L0 used for illustration purposes irectlogi L0 PL 0 * TX+ TX Signal GN Port RX+able dapter (ZL-ML shown) To L0 PL port (example RS- connection) (example device communicating across RS- connection) RX+ RX Shielded able * Termination resistors required at both ends of the network receive data signals to match the impedance of the cable (between 00 and 00 ohms). TX+ ZL-ML RX- TX- +V TX RX (Slave) -pin H -sub = do not use (male) = Sig GN = RX = do not use = do not use = do not use = do not use = do not use H = High ensity able dapter (ZL-ML shown) When connecting to a irectlogic PL use connector ZL-ML or ZL-M = TS = TS+ = RX+ = RTS- = RTS+ 0 = TX = TX+ Port GN TX TX+ RX+ ZL-ML RX- TX- TX+ +V TX RX RX RX+ shield RTS+ TS+ RTS irectlogi L0 PL TS 0 Signal GN Typical RS- Multi-rop Wiring iagram using irectlogic pin numbers to illustrate Shielded able Notes:. We recommend elden 0 shielded cable or equivalent.. Wiring iagram for this example, ZL-M(L) To -0- PL port (example RS- connection) TX+ TX RX+ RX (Slave) (example device communicating across RS- connection) - E-USER-M Hardware User Manual, st Ed. Rev. G

159 RS/ RX TX SG GN S S+ R R+ TERM EXPNSION PORT hapter - PL ommunications RS-/RS- Multi-rop Wiring iagram Examples (cont d) -pin H -sub = do not use (male) = Sig GN = RX = do not use = do not use = do not use = do not use = do not use (Slave) H = High ensity able dapter (ZL-ML shown) = TS = TS+ = RX+ = RTS- = RTS+ 0 = TX = TX+ TX+ TX Shielded able RX+ RX Signal GN L0 and L0 used for illustration purposes -more Touch Panel irectlogi L0 PL (example device communicating across RS- connection) Port Typical RS- Multi-rop Wiring iagram (cont-d) TX+ RX+ ZL-ML using irectlogic pin numbers to illustrate RX- TX- +V TX RX Notes:. We recommend elden 0 shielded cable or equivalent.. Wiring iagram for this example, ZL-M(L) To L0 PL port (example RS- connection) GN TX TX+ RX RX+ shield RTS+ TS+ RTS TS 0 TX+ TX Signal GN = do not use = do not use = do not use = Logic GN = do not use = do not use = do not use = Frame GN RX+ RX -pin -sub E-OMON- = do not use (male) = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) Shielded able Port Tx Rx PU Port Rx Tx ate code ountry of Origin E-OMON- KOYO ELETRONIS INUSTRIES O., LT. To -more Touch Panel GN R R+ S (Master) E-OMON- (Installs only on E-TL, E-TL-R, E-TL and E-TL-R panels) S+ shield * Term. SH 0 * Termination resistors required at both ends of the network receive data signals to match the impedance of the cable (between 00 and 00 ohms). Jumper pin to on the -more Touch Panel -pin connector to place the 0 internal resistor into the network. If the cable impedance is different, then use an external resistor matched to the cable impedance. Port Tx Rx US Prog. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

160 ZL-ML RX TX RS/ SG RS/ ZL-ML RX TX SG hapter - PL ommunications 0 RS-/RS- Multi-rop Wiring iagram Examples (cont d) Port RX+able dapter (ZL-ML shown) irectlogi L0 PL (example device communicating across RS- connection) TX+ RX- TX- TX- +V TX RX (Slave) Shielded able Port able dapter (ZL-ML shown) When connecting to a irectlogic PL use connector ZL-ML or ZL-M Notes:. We recommend elden shielded cable or equivalent.. Wiring iagram for this example, ZL-M(L) TX+ RX+ RX- +V TX RX Shielded able To L0 PL port To -0- PL port (example RS- connection) (example RS- connection) GN RX TX RX+ TX+ RTS+ TS+ RTS TS 0 * * Termination resistors required at both ends of the network to match the impedance of the cable (between 00 and 00 ohms). L0 and L0 used for illustration purposes -pin H -sub = do not use (male) = Sig GN = RX = do not use = do not use = do not use = do not use = do not use H = High ensity TX / RX TX+ / RX+ Signal GN = TS = TS+ = RX+ = RTS- = RTS+ 0 = TX = TX+ GN RX TX shield irectlogi L0 PL (Slave) (example device communicating across RS- connection) Typical RS- Multi-rop Wiring iagram RX+ TX+ RTS+ TS+ RTS using irectlogic pin numbers to illustrate TS 0 TX / RX TX+ / RX+ Signal GN -0 E-USER-M Hardware User Manual, st Ed. Rev. G

161 RS/ ZL-ML RX TX SG GN S S+ R R+ TERM EXPNSION PORT hapter - PL ommunications RS-/RS- Multi-rop Wiring iagram Examples (cont d) (Slave) -pin H -sub = do not use (male) = Sig GN = RX = do not use = do not use = do not use = do not use = do not use Port able dapter (ZL-ML shown) H = High ensity TX / RX TX+ / RX+ Signal GN Shielded able = TS = TS+ = RX+ = RTS- = RTS+ 0 = TX = TX+ GN L0 and L0 used for illustration purposes TX+ RX+ RX- TX- irectlogi L0 PL (example device communicating across RS- connection) +V TX RX -more Touch Panel Shielded able Notes:. We recommend elden shielded cable or equivalent.. Wiring iagram for this example, ZL-M(L) To L0 PL port (example RS- connection) RX TX shield RX+ TX+ Typical RS- Multi-rop Wiring iagram (cont-d) RTS+ TS+ RTS TS 0 using irectlogic pin numbers to illustrate = do not use = do not use = do not use = Logic GN = do not use = do not use = do not use = Frame GN -pin -sub Port Tx Rx E-OMON- PU = do not use (male) = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) TX / RX TX+ / RX+ Signal GN Port Rx Tx ate code ountry of Origin E-OMON- KOYO ELETRONIS INUSTRIES O., LT. Port Tx Rx US Prog. (Master) To -more Touch Panel GN E-OMON- (Installs only on E-TL, E-TL-R, E-TL and E-TL-R panels) R S shield R+ S+ * Term. SH 0 * Termination resistors required at both ends of the network receive data signals to match the impedance of the cable (between 00 and 00 ohms). Jumper pin to on the -more touch panel -pin connector to place the 0 internal resistor into the network. If the cable impedance is different, then use an external resistor matched to the cable impedance. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

162 hapter - PL ommunications 0 llen-radley To MicroLogix RS- communication channel = do not use = Sig GN = do not use = RX = do not use = do not use = TX = do not use To PL -Pin Port 0. I. Mini in -pin Male llen-radley MicroLogix 000/00/00/00/00 RS- (p/n E-MLOGIX-L) 0.0 Nonstandard keying TX RX GN Wiring iagram shield RX TX E-MLOGIX-L = do not use = do not use = do not use = Logic GN = do not use = RX () = TX () = Frame GN -pin -sub (male) To -more Touch Panel PL Port Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. llen-radley SL -0/0/0, ontrollogix, ompactlogix, FlexLogix, MicroLogix, F, RS- (p/n E-SL--L) = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use E-SL--L To -more Touch Panel PL Port -pin -pin -sub -sub (female) Wiring iagram = do not use (male) = do not use = do not use TX RX = do not use = do not use = Logic GN RX TX = do not use = do not use = do not use GN = RX () shield = TX () = Frame GN Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. = do not use = RX = TX = do not use = Signal GN To PL -Pin Port = do not use = do not use = do not use 0 = do not use = do not use = do not use = Signal GN = do not use = do not use = do not use = RX = TX = do not use -pin -sub (male) llen-radley PL F RS- (p/n E-PL--L) Wiring iagram = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use E-PL--L -pin -sub (male) To -more Touch Panel PL Port = do not use TX RX = do not use = do not use RX = do not use = do not use TX = do not use = do not use GN = Logic GN = do not use shield = do not use 0 = do not use = RX () = do not use = TX () = do not use = Frame GN = do not use = do not use = do not use = do not use Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use - E-USER-M Hardware User Manual, st Ed. Rev. G

163 hapter - PL ommunications llen-radley (cont d) To SL00 H- Port llen-radley SL00, /0, /0, /0 H- Point-to-Point RS- (p/n E-H-L) Wiring iagram E-H-L To -more Touch Panel PL Port RJ -pin Phone Plug -pin = TX/RX+ (P) Term. -sub = TX/RX TX/RX+ R+ = do not use (male) = do not use = do not use = do not use = do not use TX/RX 0 R = LE = Signal GN = Termination = LE S+ = Logic GN = S (RS) = do not use = do not use = S+ (RS) S = Signal GN = do not use 0 = R (RS) = do not use LE * LE * = do not use = R+ (RS) = Frame GN GN GN * Note: The LE signal is wired in the cable as shown, but not required for shield point-to-point communications. Note: Use the above wiring diagram if you need to make your own cable. We recommend elden shielded cable or equivalent. llen-radley SL 00 Modular PL ontroller - able llen-radley SL00, /0, /0, /0 H-/I to Multiple -more Touch Panels RS- (using -more cable p/n E-H-L) hannel must be set to H. Port Tx Rx PU Port Rx Tx Port Tx Rx H- Peripheral J PU J Power -I H Link oupler EXPNSION PORT US Prog. -more Touch Panel H- Link (See manufacturer s litature for details.) -more E-H-L able H- Peripheral J PU J Power -I H Link oupler -more Touch Panel Note: The above diagram shows connecting multiple -more touch panels to an llen-radley H/I network using the H Link oupler, p/n -I. Select the llen-radly H/I SL00 MircroLogix driver in the -more Programming Software when starting the project. lso, set the channel configuration for H. Port Tx Rx PU Port Rx Tx Port Tx Rx EXPNSION PORT US Prog. -more E-H-L able 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

164 hapter - PL ommunications 0 llen-radley (cont d) llen-radley SL /0 Modular PL ontroller -P RS- able llen-radley SL00 /0 H-/I to Multiple -more Touch Panels (using -more cables p/n E-MLOGIX-L, E-SL--L) hannel 0 must be set to H. Port Tx Rx PU Port Rx Tx Port Tx Rx EXPNSION PORT US Prog. -more Touch Panel -NET-I I + dvanced Interface onverter H- Link (See manufacturer s litature for details.) -more E-MLOGIX-L able -more Touch Panel -NET-I I + dvanced Interface onverter -more E-MLOGIX-L able -more E-SL--L able Note: The above diagram shows connecting multiple -more touch panels to an llen-radley H/I network using the I+ dvanced Interface onverter, p/n -NET-I. Select the llen-radly H/I SL00 MircroLogix driver in the -more Programming Software when starting the project. lso, set the channel configuration for H. Port Tx Rx PU Port Rx Tx Port Tx Rx EXPNSION PORT US Prog. To additional -more Touch Panel - E-USER-M Hardware User Manual, st Ed. Rev. G

165 ETHERNET FULT LE EXTERNL RS TX/RX PWR ETHERNET FULT LE EXTERNL RS TX/RX PWR ETHERNET FULT LE EXTERNL RS TX/RX PWR hapter - PL ommunications llen-radley (cont d) Multiple llen-radley PLs connected to multiple -more Touch Panels (using Ethernet Network Interface p/n -NET-ENI with EtherNet/IP protocol) llen-radley SL /0 Modular PL ontroller -more Touch Panel IP -NET-ENI Port Tx Rx PU Port Rx Tx Port Tx Rx mini IN to -shell cable p/n -L-P00 EXPNSION PORT US Prog. IP -NET-ENI Ethernet/IP Network llen-radley MicroLogix 000 PL ontroller Ethernet Hub or Switch 0/00 ase-t mini IN to mini IN cable p/n -L-M00 llen-radley MicroLogix 00 PL ontroller IP -NET-ENI -more Touch Panel Port Tx Rx PU Port Rx Tx Port Tx Rx EXPNSION PORT US Prog. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

166 hapter - PL ommunications 0 llen-radley (cont d) To PL -Pin Port = do not use = do not use = do not use 0 = do not use = do not use = do not use = Signal GN = do not use = do not use = do not use = RX + = TX + = do not use -pin -sub (male) = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use = do not use = do not use = RX = do not use = TX llen radley PL F RS- Wiring iagram TX + 0 RX + GN TX RX shield R S User onstructed = do not use = do not use = do not use = Logic GN = do not use = do not use = do not use = Frame GN -pin -sub (male) To -more PL Port = do not use = do not use = do not use = S = S + 0 = R = R + Notes:. Polarities must be swapped.. Handshaking is turned off. Use the above wiring diagram if you need to make your own cable. We recommend using 0 shielded cable or equivalent.. Refer to the PL- Programmable ontrollers User Manual Switch Setting Reference for details on switch settings to define the controller's serial port electrical interface. R + S + - E-USER-M Hardware User Manual, st Ed. Rev. G

167 hapter - PL ommunications GE To PL -Pin Port = TS( ) = Logic GN = do not use = +V = do not use = do not use = do not use = do not use -pin -sub (male) = TS( ) = do not use = S() = S() = R( ) 0 = R( ) = do not use GE 0/0 and 0/0 -pin -sub port, RS- (p/n E-0-0-L) S() S() R( ) R( ) 0 GN TS( ) TS( ) +V Wiring iagram shield E-0-0-L To -more Touch Panel PL Port Note: Use the above wiring diagram if you need to make your own cable. We recommend elden 0 shielded cable or equivalent. GE VersaMax Micro To PL RJ Port = RTS = TS = RX = TX = = TR = +V = GN RJ -pin Phone Plug (P) TX RX GN GE VersaMax Micro Port RS- Wiring iagram shield 0 Term. R+ R S+ S RX TX = do not use = do not use = do not use = Logic GN = do not use = do not use = do not use = Frame GN -pin -sub (male) = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) User onstructed = do not use = do not use = donot use = Logic GN = do not use = RX () = TX () = Frame GN -pin -sub (male) Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

168 hapter - PL ommunications 0 Mitsubishi To PL -Pin Port -pin -sub = do not use (male) = do not use = do not use 0 = do not use = do not use = do not use = Signal GN = do not use = do not use = Signal GN = S+ (RS) = R+ (RS) = do not use Mitsubishi FX Series -pin -sub port, RS- (p/n E-MITSU-L) Wiring iagram E-MITSU-L To -more Touch Panel PL Port = do not use S+ R+ = do not use = do not use = do not use S 0 R = do not use = do not use = do not use = do not use R+ S+ = do not use = Termination = do not use = Logic GN R = S (RS) S 0 = do not use = do not use = S+ (RS) = do not use GN = do not use 0 = R (RS) = do not use = do not use = R+ (RS) GN = do not use = Frame GN = S (RS) shield = R (RS) = do not use Note: Use the above wiring diagram if you need to make your own cable. We recommend elden 0 shielded cable or equivalent. To PL -Pin Port Term. Mitsubishi FX Series -pin MINI-IN, RS- (p/n E-MITSU-L-) -pin -sub (male) E-MITSU-L- To -more Touch Panel PL Port Mini in Wiring iagram Term. -pin -pin Male = R (RS-) -sub S+ R+ = do not use = R+ (RS-) (male) = do not use = do not use = Sig GN S 0 R = do not use = do not use = S (RS-) = Termination R+ S+ = Logic GN = do not use = S (RS) = do not use = do not use R S = S+ (RS) = do not use = S+ (RS-) 0 = R (RS) GN = do not use = do not use = R+ (RS) shield = Frame GN Note: Use the above wiring diagram if you need to make your own cable. We recommend elden 0 shielded cable or equivalent. To PL -Pin Port = RX () = TX () = Logic GN = do not use = do not use = do not use Mini in -pin Male Mitsubishi Q0 / Q0H / Q0H / QH / QH Serial river and Qn Serial river with irect onnection to the Serial Port on Q00 and Q0 PU s RS- TX RX GN Wiring iagram shield RX TX User onstructed = do not use = do not use = donot use = Logic GN = do not use = RX () = TX () = Frame GN -pin -sub (male) Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use - E-USER-M Hardware User Manual, st Ed. Rev. G

169 hapter - PL ommunications Mitsubishi (cont d) To PL -Pin Port User onstructed Wiring iagram -pin -pin -sub TR -sub (female) SR = do not use (male) = do not use = SR RS = do not use = RS S = Logic GN = S = do not use TX = do not use RX = RX () RX TX = TX () = Frame GN GN shield Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. = = RX = TX = TR = Signal GN Mitsubishi Q / Qn Serial PL QJN RS- To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

170 hapter - PL ommunications 0 Omron To PL -Pin Port = do not use = do not use = do not use 0 = do not use = do not use = do not use = Signal GN = do not use = TS = RTS = RX = TX = do not use To PL -Pin Port = do not use = TX = RX = RTS = TS To Peripheral Port able = do not use = RX = TX = do not use = Signal GN -pin -sub (male) Omron Host Link (00 dapter, 00), RS- (p/n E-OMRON-L) Wiring iagram E-OMRON-L -pin -sub (male) To -more Touch Panel PL Port = do not use TX RX = do not use = do not use RX = do not use = do not use TX = do not use = do not use GN = Logic GN = do not use RTS = do not use 0 = do not use = RX () = do not use TS = TX () = do not use = Frame GN = do not use shield = do not use = do not use = do not use Note: Use the above wiring diagram if you need to make your own cable. We recommend using WG shielded cable. Omron FINS (QM, PM, PM, 00, J & S) RS- = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use User onstructed -pin -pin -sub -sub (male) Wiring iagram = do not use (male) = do not use = do not use = do not use TX RX = do not use = Logic GN RX TX = do not use = do not use = Signal GN SG = RX () = TX () RTS = Frame GN TS shield Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use User onstructed Omron Host Link QM using QM-IF0 Peripheral Port onnecting able RS- -pin -pin -sub -sub (male) Wiring iagram = do not use (male) = do not use = do not use = do not use TX RX = do not use = Logic GN RX TX = do not use = do not use = do not use GN = RX () = TX () = Frame GN shield Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use -0 E-USER-M Hardware User Manual, st Ed. Rev. G

171 hapter - PL ommunications Modicon Modbus RS- To PL -Pin Port = do not use = RX = TX = TR = Signal GN Modicon Modus, PU, Quanum PU RS- User onstructed -pin -pin -sub -sub (male) Wiring iagram = do not use (male) = SR = do not use TX RX = do not use = RTS = TS = do not use = do not use GN = RX () = TX () TR = Frame GN SR RX TX = Logic GN RTS TS shield Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. Modicon Micro Series To PL -Pin Port = do not use = TX = RX = do not use = Signal GN EG Modicon Micro Series: 0 PU -xx, 0 PU -xx, 0 PU -xx, 0 PU -xx RS- To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use User onstructed -pin -pin -sub -sub (female) Wiring iagram = do not use (male) = do not use = do not use = do not use TX RX = do not use = Logic GN RX TX = do not use = do not use = do not use GN = RX () = TX () = Frame GN shield Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. Modicon Modbus with RJ To PL RJ Port = do not use = do not use = TX = RX = Logic GN = RTS = TS = do not use Modicon Modus with RJ RS- To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use User onstructed RJ -pin Wiring iagram -pin Phone Plug -sub (P) TX RX = do not use (male) RX TX = do not use GN = donot use = Logic GN RTS = do not use TS = RX () = TX () shield = Frame GN Note: Use the above wiring diagram to make your own cable. We recommend using WG shielded cable. To -more Touch Panel PL Port = do not use = do not use = do not use = do not use = do not use 0 = do not use = do not use 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

172 hapter - PL ommunications 0 Siemens To PL -Pin Port = Logic om = Logic om = RS Sig = do not use = Logic om -pin -sub (male) = + V = + V = RS Sig = do not use Siemens S-00 PU Port 0 or RS- RS- Signal RS- Signal Logic ommon Wiring iagram 0 shield User onstructed To -more Touch Panel PL Port Note: Use the above wiring diagram to make your own cable. We recommend utomationirect L shielded cable or equivalent. Term. R+ = do not use S+ = do not use = do not use R = Logic GN S = do not use = do not use = do not use = Frame GN -pin -sub (male) = do not use = do not use = Termination = S (RS) = S+ (RS) 0 = R (RS) = R+ (RS) - E-USER-M Hardware User Manual, st Ed. Rev. G

173 Maintenance hapter In This hapter... Project ackup...- heck Operating Environment...- heck Operating Voltage...- heck Status Indicators...- heck Physical onditions...- Run Tests under System Setup Screens...- heck Memory Usage...- heck/djust isplay rightness...- heck Error Log...- djust Touch Panel...- leaning the isplay Screen...- heck Project Functionality...- hecks from -more Programming Software...- Notes:...-

174 hapter - Maintenance 0 Maintenance lthough the -more touch panels require very little maintenance, setting up a routine maintenance schedule will ensure the longevity of the product in your application. The following are some suggestions of items to include in a preventive maintenance list or schedule. Most of these items should be scheduled quarterly or semi-annually. Project ackup uring routine preventive maintenance is a good time to make sure that there is an up-todate backup of the application project. lthough the -more touch panel has the ability to upload the complete project from a panel through the programming software, insurance is warranted just in case the worse case scenario happens and the entire touch panel is destroyed. heck Operating Environment Make sure the touch panel is operating in the proper temperature range: 0 to 0 ( to F). Make sure the touch panel is operating within the specified humidity range: ( % RH, non-condensing). Make sure the operating environment is free of corrosive gasses. heck Operating Voltage heck the input voltage that is powering the touch panel to make sure it is within the appropriate range. : - V : If the panel is being powered from an / Power dapter, E-, then the acceptable input voltage range to the adapter is 00-0 V, 0/0 Hertz. heck Status Indicators uring routine maintenance is a good time to take a quick look at the status indicators on the front and rear of the touch panel. The Power LE (PWR) indicator should be on and there should be activity on the Tx and Rx LE indicators when connected serially to a PL or control device. heck the status of the PU LE and compare it to the chart shown in the illustration below. ny indication of the PU LE other than a solid green shows there is a possible problem, and the condition needs to be corrected. Power LE (Green) On Power On Off Power Off User efined LE (Green, Orange & Red) Off Green Red User efined (Refer to online help Orange file for further details) linking Red linking Orange linking Green Front View Port Tx Rx PU Port Rx Rear View Tx Port Tx Rx ORROSIVE PU Status LE (Green, Orange & Red) Off Power Off Green Normal PU Run State Red Memory Error linking Watchdog Timer Error Red linking Orange OS Error linking Green Power Loss etection Serial Tx/Rx LE (Green) On omm. is active Off No communication - E-USER-M Hardware User Manual, st Ed. Rev. G

175 hapter - Maintenance heck Physical onditions Make sure that harmful chemicals are not being used around the panel. Look for any deterioration of the touch panel s bezel and front display area. heck the mounting gasket to make sure it is sealing properly and has not deteriorated. Replace the mounting gasket if there are any signs of deterioration, or if there is any evidence that moisture/liquids have penetrated to the inside of the enclosure where the panel is mounted. Information on a replacement gaskets can be found in hapter : Replacement Parts. p/n E-xx-GSK heck to make sure that none of the cooling vents around the inside section of the touch panel are clogged with dust or debris. lso make sure that there is clearance around the touch panel as shown in hapter : Installation and Wiring. Run Tests under System Setup Screens Use the touch panel s System Setup Screens to test the touch screen, display, communication ports, beeper and audio output (only with external amplifier and speaker(s) connected). See hapter : System Setup Screens for additional details for the Test Menu. Test Touch Panel - allows the user to check the analog touch function of the screen by drawing free hand lines and shapes across the entire touch area. The display will retain the lines where the screen has been touched until the ancel button is pressed. Test isplay - used to test the display and color rendition. test pattern will first show both the primary colors and a gray scale. If the touch screen is not pressed within a few seconds, the display will go into alternating color sweeps across the screen until the panel is pressed again. If the screen is pressed when the test pattern first appears, it will stay in this mode until the ancel button is pressed. Test omm. Port - used to test the functionality of the -pin PL communication serial port, the -wire terminal block RS- port, the RJ RS- port and the Ethernet port. loop-back connector can be fabricated and used on the serial ports to test the RS- or RS-/ communications for the Tx and Rx signals and also the RTS and TS signals if applicable. The Test omm. Port setup screens and hapter show pin-outs for the RS- and RS-/ loop-back connectors. The Ethernet connection can also be tested for communications if it is at least connected to an Ethernet switch. If the touch panel is connected to a PL, then an inquiry test can also be done to test the communications between the panel and the PL. Press the ancel button when finished to return to the Test Menu screen. Test eep/sound - used to test the touch panel s internal beeper and also test the audio line output port with an external amplifier and speaker(s) connected. Testing the audio output is done by playing an included internal WV file. Press the ancel button when finished to return to the Test Menu screen. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

176 hapter - Maintenance 0 heck Memory Usage good time to check and record the touch panel s memory usage for future reference is during a routine maintenance schedule. The various memory devices being used by the panel are listed under the tab. This includes internal memory as well as any external memory device such as a US pen drive or S card memory. If no external memory device is inserted, it will not show up on the list. The memory usage can be viewed by use of the panel s System Setup Screen s Main Menu, and then selecting the Information button then the Memory tab. See hapter : System Setup Screens for additional details on using the Memory tab. heck/djust isplay rightness Is is good practice to occasionally check the display brightness or contrast and adjust as required. This is done by using the Setting Menu in the System Setup Screens. See hapter : System Setup Screens for additional details. heck Error Log nother good practice is to review the touch panel s Error Log. The log can be viewed by use of the panel s System Setup Screen s Main Menu, and then selecting the Information button. Look under the Error tab. See hapter : System Setup Screens for additional details on using the Error tab, ppendix : PL Protocol Error odes for a list of the error codes as they relate to the specific PL that is being used with a description of the error, and ppendix : Touch Panel Runtime Errors for a list of errors that may occur when the panel is in operation. djust Touch Panel It is recommended that a regularly scheduled maintenance program include adjusting the touch panel. The adjustment calibrates the touch area of the panel. The procedure should also be done anytime that it seems the touch area being pressed for an object is out of position by a small amount. The procedure is done by using the Setting Menu in the System Setup Screens and then selecting the djust Touch Panel button. See hapter : System Setup Screens for additional details. - E-USER-M Hardware User Manual, st Ed. Rev. G

177 hapter - Maintenance leaning the isplay Screen The display screen should be cleaned periodically by wiping it with a lint free damp cloth using a mild soap solution. ry the surface when finished with a lint free cloth. o not clean with ammonia based products which are solvents and will damage the face of the panel. The longevity of the display can be increased by the use of a non-glare screen protector, p/n E-XX-OV, where XX = touch panel screen size,,,, 0,, or. See E--OV hapter : ccessories for additional information on the screen protectors. To prevent damage to the display screen, avoid touching the screen with sharp objects, striking the screen with a hard object, the use of abrasives near the screen, or using excessive force when pressing the touch screen. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

178 hapter - Maintenance 0 heck Project Functionality uring routine maintenance is a good time to check the functionality of your application, making sure that various areas on different screens do what they were designed to do. n outline or specification for the application is a useful tool for testing the various aspects of your application. s a starting point, you may want to run through all the screens to make sure they are accessible. If there are any trouble-shooting procedures built into the touch panel application, now is a good time to also check these aids. hecks from -more Programming Software If you have a P available with the -more programming software, E-PGMSW, installed, and the P is connected to the touch panel, there are checks you can make to the status of the touch panel by using the Panel Information... feature located under the Main Menu heading Panel. This includes the following: onnected panel details Memory availability and usage Revisions Other functions that can be accessed from the programming software directly to the touch panel include: isplayscreen, Reboot, djustlock, Memorylear, and Update Firmware. dditional information for these functions can be found in the -more programming software online help file. - E-USER-M Hardware User Manual, st Ed. Rev. G

179 hapter - Maintenance Notes: 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

180

181 Troubleshooting hapter In This hapter... ommon Problems...- Troubleshooting Flow hart...- Touch Panel does not Power up...- isplay is lank...- isplay is im...- No User Program...- Firmware Recovery Tool...- No System Found...- No ommunications between Panel and P (Personal omputer) via US...-0 US river Troubleshooting...- No ommunications between Panel and P (Personal omputer) via Ethernet...- No ommunications between Panel and PL...- IP ddress in System Setup Screens displays ifficulty onnecting to the Panel over the Internet (Web server and Remote ccess features)...- PL Protocol Error odes...- Touch Panel Runtime Errors...- Panel onstantly isplays Initializing when Powering up...- ata not Logging Problems...- Electrical Noise Problems...-

182 hapter - Troubleshooting 0 The following topics are some of the more likely problems that may be encountered during the installation and operation of your -more touch panel. We have made some suggestions on what to check in order to correct the problem. Please start with the troubleshooting flow chart that covers the more common problems encountered by other users. ommon Problems The troubleshooting flow chart shown on the following page is based on the more common problems fielded by our technical support team. If you are having problems, please start with the flow chart, follow the suggestions listed, and if you still need help, call our tech support In addition to having ready the information suggested in the flow chart, please have the following available: ) -more touch panel part number including serial number with date code. Why is this information important? The various sizes of the touch panel use different processors and memory sizes, and therefore can have different types of problems within the particular panel size. ) Programming software version that you are currently using. For example: Version.0. Having the software version number will allow our tech support team member to assess whether there are similar problems that have been reported when using the same version of the software. The programming software version can be found by clicking on bout -more Programming Software... selection under the Help pull down menu in the software. lso, it is always a good practice to visit the Software/Firmware ownloads area under the Tech Support section of the utomationirect website and check to see if you are using the latest version of the programming software. If you aren t using the latest software version, we suggest that you upgrade to see if this resolves your problem. NOTE: The bout -more Programming Software... dialog box will show a Firmware version. This is the current firmware version that is included with the programming software and does not reflect what firmware is actually loaded on your -more touch panel. See the following for details on how to check the firmware version. ) Firmware version of the -more touch panel. For example: V.0. The firmware version can be checked by using the System Setup Screens, going to the Information menu under the Main Menu, and looking under the General tab for Firmware: -Runtime. The firmware version can also be checked by using the programming software, while connected to the panel, and clicking on the Panel Information selection under the Panel pull down menu. s with the programming software version, it is important for our tech support associates to know which firmware version you are using so they can check on any known problems. s with the programming software, we strongly suggest that the firmware be updated to the latest version. heck for the latest version and download from the Software/Firmware ownloads area of the utomationirect website. It is also helpful to have a copy of your project file for our tech support associates to use in troubleshooting a problem, so please be prepared to forward a copy of your project if it is requested. - E-USER-M Hardware User Manual, st Ed. Rev. G

183 hapter - Troubleshooting Troubleshooting Flow hart STRT P omm Issue? No PL omm Issue? No lank or im Screen? No Yes Yes Yes Look at the table of contents for this chapter to see if your particular problem is listed, else call our tech support Try the following: ) heck for proper grounding on panel and P. ) Go to section No ommunications between Panel and P. ) P connected to panel via US: a) If using US Hubs, disconnect all hubs and other US devices, but leave US keyboard and mouse connected. b) heck in the Window s device manager to see if the -more panel s US connection shows up when physically connected. ) P connected to panel via Ethernet: a) heck to make sure the cable is properly connected to the correct port on the P and panel. If the above steps did not resolve the problem, then contact our tech support team with the information listed on the previous page plus the following: a) escription of the network to which the -more panel is connected. b) Isolated Network or Office/Plant Network? Try the following: ) heck for proper power connection & grounding on panel & PL. ) Go to section No ommunications between Panel and PL ) Go to section IP ddress in System Setup Screens displays If the above steps did not resolve the problem, then contact our tech support team with the information listed on the previous page plus the following: a) PL make and model? PL firmware version? b) Serial or Ethernet? If serial, RS-//? c) PL protocol being used, and PL comm port being used? d) able purchased from or constructed by user? Having the PL and -more project files available to to tech support always helps in the troubleshooting process. Try the following: ) White screen? Make sure a project is loaded into the panel. ) lack Screen? heck the PWR LE to make sure it is Steady Green. ) Go to section Touch Panel does not Power up ) Go to section isplay is lank ) Go to section isplay is im ) heck PU LE: a) Green - OK b) Off - No Power c) Red - Memory Error - ycle power to the panel. If problem persists, replace panel d) linking Red - Watchdog Timer Error - cycle power, update firmware e) linking Orange - Operating System Error, update firmware f) linking Green - Power Loss etection - check voltage at power source. If the above steps did not resolve the problem, then contact our tech support team with the information listed in this manual. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

184 hapter - Troubleshooting 0 Touch Panel does not Power up.) heck the status indicators on the front of the panel to see if the Power LE (Green) indicator is on. Refer to the diagram below. If the Power LE (Green) indicator is on and the panel was observed showing Initializing... during power up, but the display is now blank, go to the next troubleshooting tip, isplay is lank..) If the Power LE (Green) indicator is off and the panel is being powered with a or V power source, use a voltmeter to check the incoming voltage level. If the incoming voltage is zero, check any fusing that may be in the circuit. If the fuse is open, determine cause and replace. If the voltage level is out of range, the power source needs to be corrected or replaced..) If the Power LE (Green) indicator is off and the panel is being powered with an / Power dapter, E-, use a voltmeter to check the incoming power. The voltage to the / Power dapter should be in the range of 00 to 0 V, 0/0 Hertz. If the incoming voltage is zero, check any fusing that may be in the circuit. If the fuse is open, determine cause and replace. If proper voltage is present on the / Power dapter, but the Power LE (Green) indicator is off, replace the / Power dapter, E-. User efined LE (Green, Orange & Red) Off Green Red User efined Orange (Refer to online help file for further details) linking Red linking Orange linking Green Front View Power LE (Green) On Power On Off Power Off - E-USER-M Hardware User Manual, st Ed. Rev. G

185 hapter - Troubleshooting isplay is lank.) Touch the screen to make sure the panel is not in the Screen Saver mode. The Screen Saver will be turned off and the panel screen will display: If a PL ddress is configured to control the Screen Saver and changes from On to Off. When the panel touchscreen is touched. When the screen is clicked by Remote ccess. When the larm Event of the Event Manager occurs. (Only when the isplay setting of the larm Event is checked). When there is a screen change by the PL. When an Error such as a ommunication Error occurs..) If the panel is not in Screen Saver mode, check the status indicators on the rear of the panel. PU Status LE (Green, Orange & Red) Off Power Off Green Normal PU Run State Red Memory Error linking Red Watchdog Timer Error linking Orange OS Error linking Green Power Loss etection Port Tx Rx PU Rear View Port Tx Rx Tx/Rx LE (Green) RxSerial Port Tx On omm. is active Off No communication Make sure the PU status LE (Green, Orange, Red) is a steady Green. If the PU status LE is blinking Green, then the supply voltage is below V, or below 00 V when using the optional -more / Power dapter, E-. The backlight will turn off immediately to extend the power retention period. The panel will continue to run and the L display may be slightly visible. This may be seen as the display being dim, so it is advisable to check the incoming voltage. blinking Orange PU status LE indicates that the operating system could not be found. Reload the firmware to the touch panel. If this does not resolve the problem, the panel must be replaced. isplay is lank continued on next page. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

186 hapter - Troubleshooting 0.) There is always the remote possibility that a project has been transferred to the touch panel that includes a screen that uses a black background and has no objects placed on the screen. To check for this possibility, access the Main Menu of the touch panel System Setup Screens by pressing the extreme upper left corner of the panel display area for three () seconds as shown below. If the System Setup Screen s Main Menu is displayed, then most likely an empty black background screen is being displayed. NO USER PROGRM isplay is im.) heck the brightness setting found under the System Setup Screens. See hapter : System Setup Screens for additional information..) acklights will lose some luminance over time causing the display to slightly dim. The backlight average lifetime is rated at 0,000 hours and is defined as the average usage time it takes before the brightness becomes 0% of the initial brightness. The lifetime of the backlight depends on the ambient temperature; the lifetime decreases in low or high temperatures. To improve the backlight life, use the Start Screen Saver function that is available in the -more Programming Software in the Panel Manager dialog box. isplay is im continued on next page. - E-USER-M Hardware User Manual, st Ed. Rev. G

187 hapter - Troubleshooting The Screen Saver will be turned off and the panel screen will display: If a PL ddress is configured to control the Screen Saver and changes from On to Off. When the panel touchscreen is touched. When the screen is clicked by Remote. When the larm Event of the Event Manager occurs. (Only when the isplay setting of the larm Event is checked). When there is a screen change by the PL. When an Error such as a ommunication Error occurs..) nother condition that may make the display appear dim is to view the touch panel in direct sunlight or in a location where direct light is reflected onto the display. The -more touch panel displays have isplay rightness ratings of 0 to 0 cd/m (NITS), depending on the particular model. The higher the cd/m (NITS) rating, the more visible the display will be under bright lighting conditions. NOTE: The -more panel is not rated for direct sunlight. No User Program NO USER PROGRM If the touch screen is displaying the message No User Program after it has powered up, then either: the built-in Flash memory does not contain a recognized project, or an S memory card is plugged into the S slot and there is no project on the S memory card. Turn the power off, remove the S memory card and turn the power back on. Keep in mind that on power up, the touch panel will either copy the project from its internal Flash memory to its internal SRM memory and run the project, or if an S memory card is plugged into the S slot, then any project contained on the S memory card will be loaded to the panel s internal SRM memory and be run. In other words, the memory of an S card in the S slot will override the panel s internal Flash memory on power up or reboot, even if the S memory card does not contain a project. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

188 hapter - Troubleshooting 0 Firmware Recovery Tool If the panel power is interrupted during a firmware update, the firmware and/or operating system in the panel may become corrupt. The panel may be recoverable using a recovery utility that installs when the -more Programming Software is installed. If the firmware is corrupt, but the operating system is still intact, the screen below will open when power is reapplied to the panel. This is called Safe Mode Press the Information button and the Information Screen shown below will display. Notice that the runtime version is blank. To recover, start the firmware update again making sure that there is a constant clean power supply. - E-USER-M Hardware User Manual, st Ed. Rev. G

189 hapter - Troubleshooting No System Found If the operating system is corrupt, the screen will display No System Found. To recover the panel s Operating System:. onnect the Panel to your P with the US programming cable. (ny standard US printer cable will also work.). lose the -more Programming Software.. ycle the power on the panel.. From the Windows Start Menu select: Start Menu > utomationirect > -more > Special Tools > -more E Series Recovery Tool The window shown below will open. NOTE: If the US Icon is blinking and the US light is Red, this indicates that there is a communication problem to the panel. heck that the US cable is properly connected and make sure there is communication to the panel.. Select Start and the Operating System will be loaded to the panel. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

190 hapter - Troubleshooting 0 No ommunications between Panel and P (Personal omputer) via US The -more touch panel is programmed using the -more Programming Software, E-PGMSW. The developed project is transferred from the P to the touch panel by either a US or an Ethernet connection between the two. (Ethernet available on full feature units only.) If using US, then a US type programming cable, such as p/n US-L-, should be used to make a connection between the panel s US Port, Type and a US port on the P. The -more Programming Software will install a US driver on the P during the software installation. P US Port US-L-xx US able -more Touch Panel If the US connection to the panel is recognized by the P, you will hear the Windows device-recognized-sound when the powered panel is connected to the P. The driver will appear in the Windows evice Manager as -more HMI. US Port -0 E-USER-M Hardware User Manual, st Ed. Rev. G

191 hapter - Troubleshooting No ommunications between Panel and P (Personal omputer) via US (cont d) The -more software will then identify the US connection with a green indicator. This ommunication indicator appears on the Panel tab in the Navigation window and in the Project Transfer or Read from Panel windows. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

192 hapter - Troubleshooting 0 US river Troubleshooting heck the US driver using Windows evice Manager: With the -more panel connected to the P, on the P, open ontrol Panel--> System -->Hardware tab --> evice manager. Next expand Universal Serial us controllers. The -more driver is named -more HMI as shown below: If the -more programming software ommunication onfig dialog US indicator is red, and the driver does not appear in evice Manager, ) Unplug both end of the cable and replug them in. ) If that does not establish communication, plug into a different US port on the P. ) If there are any US hubs or other devices being used, temporarily eliminate them to see if this solves the problem. ) Reinstall the -more HMI US driver. - E-USER-M Hardware User Manual, st Ed. Rev. G

193 hapter - Troubleshooting US river Troubleshooting (cont d) The -more US driver installation utility is bundled with the -more software installation files. If you have a -more software, the file is in the root, called -moreusriver.exe. If you downloaded the software, when you extracted the files, the -moreusriver.exe was extracted to the location you chose. First, close the -more software and disconnect the US cable from the P. Then, browse to -moreusriver.exe and run it. Plug the US cable into the P and the -more panel. The Found New Hardware Wizard will prompt you to search for the driver. Select No not this time, click Next. Select Install the Software automatically (Recommended) click Next. lick ontinue nyway in the Windows Logo warning popup. lick Finish. Open the project in the -more software. The ommunication onfig (and Transfer Project) US indicator should be green. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

194 hapter - Troubleshooting 0 No ommunications between Panel and P (Personal omputer) via Ethernet When using an Ethernet connection to communicate between the touch panel and the P and the communications does not seem to be working, the first area to check is the Ethernet status indicators located next to the 0/00 ase-t Ethernet Port on the rear of the panel. The Link Status LE must be displaying a steady or blinking green. Link Status LE (Green) On Ethernet Linked Off No Ethernet omm. linking Green omm. ctivity Network Speed LE (Yellow) On 00M Off 0M If using Ethernet, there are two basic ways to make the connection. You can use an Ethernet cable to make a direct connection between the touch panel and P or use an Ethernet cable from the touch panel to a switch and then to the P. P P Ethernet Port Ethernet Port Ethernet T able Ethernet T able -more Touch Panel uto MI / MI-X Ethernet Port Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) -more Touch Panel uto MI / MI-X Ethernet Port Use the -more programming software to check the status of the Ethernet communications. From the Navigation window, select the Panel tab. t the bottom of the Panel tab is the ommunication onfig dialog box. Select the rowse button. If the connection is working the panel will be listed in the online link list. Select the panel and then select OK. If the Ethernet communications to the panel is working, then there should be a green indicator next to the Ethernet selection. There should also be an IP ddress shown in the browse box below the Ethernet selection. If the Ethernet radio button is red, then you will need to check your Ethernet cables and connections or rowse for the panel. - E-USER-M Hardware User Manual, st Ed. Rev. G

195 hapter - Troubleshooting No ommunications between Panel and P (Personal omputer) (cont d) There can also be a conflict with another Ethernet connection that may be using the same IP ddress. You may want to check the setup both in the touch panel and also in your P. s a starting point, it is best to start with an assigned IP ddress and Subnet mask, mainly to eliminate IP addressing conflicts. Use the -more programming software and open the Touch Panel Network dialog box under the Main Menu s Setup drop down menu. lick on the Ethernet Port tab to display the dialog box used to set up the touch panel s Ethernet port. nother cause of an Ethernet communications problem that may be encountered, is the touch panel doesn t show up in the node list, which can be caused by the P having a firewall. The figure below shows the Touch Panel Network dialog box with the Ethernet port tab opened. The Save settings to Project check box is checked and we are using the Use the following IP ddress selection by checking its radio button. The subnet (..00.X) and the subnet mask (...0) must be the same for both the panel and the P. See the -more programming software on-line help for additional details regarding the Touch Panel Network. In the example shown here, the subnet is..00.x, the subnet mask is...0, and both need to be the same for all the Ethernet devices connected together. The IP ddress assigned to the touch panel can also be checked or edited by using the system setup screens built into the touch panel. See hapter : System Setup Screens for additional information. The figure to the left shows a different example of the panel s System Setup Screens Ethernet Port dialog box for configuring the Ethernet port. gain, make sure the subnet (0..0.x) and subnet mask (...0) is the same for both the panel and the P. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

196 hapter - Troubleshooting 0 No ommunications between Panel and P (Personal omputer) (cont d) nother option for accessing the IP ddress assigned to the touch panel is to use the -more Programming Software. Open the Navigation window s Panel tab and click on the rowse button under the ommunication window at the bottom. This will open the Ethernet onnection Setup window. The Online Link List tab will show all of the connected panels. If none are shown, try clicking the rowse Network button to search for attached devices. ouble click on the Panel Name you want to access and this will bring up the hange IP ddress window. In this window changes can be made to the panel s name, IP address, subnet mask, and default gateway. - E-USER-M Hardware User Manual, st Ed. Rev. G

197 hapter - Troubleshooting No ommunications between Panel and P (Personal omputer) (cont d) heck the IP ddress setting of the P by opening the Windows operating system s ontrol Panel and then selecting the Network onnections utility. lick on Properties, scroll down to Internet Protocol (TP/IP) and click Properties. The Internet Protocol (TP/IP) Properties dialog box will open. gain, make sure the Subnet Mask is set the same for both the panel and the P and also make sure that the IP ddresses do not conflict. NOTE: If a HP Server is being used to obtain the IP ddress for the P, there are ways to identify the IP ddress. For example, if using Windows XP, open a ommand Prompt (Run > M) and type IPONFIG /LL. list of all Ethernet assignments for the P will be shown. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

198 hapter - Troubleshooting 0 No ommunications between Panel and PL The communications between the -more touch panel and designated PL or controlling device can be accomplished by either a serial connection or by an Ethernet connection to the panel s 0/00 ase-t Ethernet Port. (Ethernet available on full feature units only.) ll panels include a -pin RS-// port. Full featured panels include a -wire RS- connection and an RJ RS- connection..) If the touch panel and PL are connected serially and the communications have seemed to stop working, then first check the Tx and Rx status indicators on the rear of the panel at the connected port for activity. L-0 PL E-L- Port Port -more Touch Panel If there is no activity on one or both the Tx and Rx status indicators, then it should be suspected that either: serial comm port settings are incorrect the cable is bad and needs to be replaced the serial port on the panel is defective the PL serial port is bad No Tx also can indicated no tags being polled on device PU Status LE (Green, Orange & Red) Off Power Off Green Normal PU Run State Red Memory Error linking Red Watchdog Timer Error linking Orange OS Error linking Green Power Loss etection Port Tx Rx PU Rear View Port Tx Rx Tx/Rx LE (Green) RxSerial Port Tx On omm. is active Off No communication The status indicators will show activity whether the serial communications is wired for RS- or RS-/. Electrical noise, pulse generating wiring and/or improper grounding can also cause problems with communications. Refer to the Electrical Noise Problems section later in this chapter for additional help. - E-USER-M Hardware User Manual, st Ed. Rev. G

199 hapter - Troubleshooting No ommunications between Panel and PL (cont d) The serial ports on the -more touch panel can be tested using the panel s system setup screens. ccess the Main Menu of the panel s system setup screens, press the Test Menu button, then press the Test omm. Port button and select the appropriate port tab. You will need to fabricate a Loop ack onnector for the type of serial connection that is being used in your application, either RS- or RS-/, per the wiring diagrams shown below. Plug the loop back connector into the panel s -pin PL serial communications port and then press the Loop ack Test button to run the test. See hapter : System Setup Screens for additional information. Loop back connector wiring diagrams: RS- Loop-back onnector -pin -sub (male) TX RX TS RTS Wiring iagram RS-/ Loop-back onnector TS RTS -pin -sub (male) RX+ TX+ 0 RX TX Wiring iagram System setup screens Test omm. Port dialog boxes: RS- Loop-back onnector RJ (male) RX TX Wiring iagram The PL Enquiry Test can also be performed to determine if the Ethernet communication is working correctly between the panel and designated PL. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

200 hapter - Troubleshooting 0 No ommunications between Panel and PL (cont d).) If using an Ethernet connection between the touch panel and the PL, and there is a problem with the communications, the first area to check is the Ethernet status indicators located next to the 0/00 ase-t Ethernet Port (shown below) on the rear of the panel. Link Status LE (Green) On Ethernet Linked Off No Ethernet omm. linking Green omm. ctivity Network Speed LE (Yellow) On 00M Off 0M There are two basic ways to make the connection. You can connect directly from the touch panel to the PL or connect from the touch panel to a switch that is also connected to the PL. H0-EOM/H0-EOMM00 Ethernet Module L0 PL Ethernet T able Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) H0-EOM/H0-EOM00 Ethernet Module L0 PL Ethernet T able -more Touch Panel uto MI / MI-X Ethernet Port -more Touch Panel uto MI / MI-X Ethernet Port heck the status indicators that may be included with the Ethernet communications module or device that is part of the PL. Refer to the PL s Ethernet user manual for further troubleshooting information. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

201 hapter - Troubleshooting No ommunications between Panel and PL (cont d) The Ethernet port on the -more touch panel can be tested by using the panel s system setup screens. ccess the Main Menu of the panel s system setup screens, press the Test Menu button and then press the Test omm. Port button. Select the Ethernet tab in the Test omm. Port dialog box, make sure the Ethernet port is connected to an Ethernet switch or other Ethernet communications device select a PL from the drop down selection box, and then press the PL Enquiry button to run the test. See hapter : System Setup Screens for additional information. If a P running the -more programming software is connected to the Ethernet network that is also connected to both the touch panel and PL, then certain functions in the software, such as the Main Menu s Setup drop down selection for Panel Manager or Touch Panel Network and the Main Menu s Panel drop down selection for Panel Information, can be used to help troubleshoot problems with the touch panel s communications and operation. See the -more programming software s on-line help for additional information. IP ddress in System Setup Screens displays NOTE: If entering an IP ddress for the -more touch panel using the System Setup Screens, and the IP ddress keeps displaying , even after entering an IP address, the panel is not functionally connected to an active network. Either the cable, hub, or switch is bad. The entered IP ddress is stored in the panel s memory, but won t show up until a good connection is established. Keep in mind that if in the -more programming software s Touch Panel Network dialog box, under the Ethernet Port tab, you have checked the Save settings to Project check box and have entered an IP ddress of , then anytime the project is transferred to the panel, the panel s IP ddress will be overwritten with the entered address. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

202 hapter - Troubleshooting 0 ifficulty onnecting to the Panel over the Internet (Web server and Remote ccess features) ) Refer to the software help file topics Touch Panel Network and Remote ccess Setup for information on configuring the Remote ccess accounts, the Web Server Function and the panel IP ttributes. ) In the Ethernet Port tab if HP is selected for assigning the IP address, verify the currect address of the panel. The IP address assigned by HP may change over time. ) Note that the Web Server Function must be enabled on the Web Server tab before the Remote ccess Server Function can be accessed on the panel. ) Verify that the correct TP ports have been opened and forwarded on the router controlling access to the network where the -more panel resides. ) If two -more panels are on a network behind a firewall and they have the same Remote ccess port number, the router will use the first entry in the Port Forwarding setup that it encounters. The same -more panel will always come up even if the two panels have two different Web Server Port numbers. ) When entering the URL in Internet Explorer to connect the -more web server using a port number other than the default (0), be sure to use the full URL text including the prefix The URL should be where xxx.xxx.xxx.xxx is the IP address of the panel and aaaaa is the port number configured in the Web Server tab of the Touch Panel Network setting. - E-USER-M Hardware User Manual, st Ed. Rev. G

203 hapter - Troubleshooting PL Protocol Error odes The -more touch panel includes built-in PL communication protocol diagnostics that monitor the exchange of data between the panel and the PL. The diagnostics look for the proper exchange of data, correct handshaking signals, addressing errors, incorrect data bytes, wrong packet format, etc. The diagnostics also monitor and report any of the errors that the designated PL would normally generate if there is a problem with the PL s communications. Each brand of PL has its own unique set of diagnostic errors that are typically communicated over the PL s communications port. The PL generated errors are interpreted by the -more software. See the PL manufacturer s user manuals for additional details on the designated PL s errors. If a -more communications error does occur, the error message will be displayed in the upper left of the -more screen and the Error ode is recorded in the panel s error log. If a PL error occurs, the PL error code number will appear across the top of the screen, the PL error message may not be included in some cases. The error log can be viewed using the system setup screens. See hapter : System Setup Screens under the Information window to bring up the Error tab which includes a description of the logged data. detailed list and description of the various PL protocol errors can be found in ppendix : PL Protocol Error odes. PL Protocol Error odes example: Error odes for irect LOGI K-Sequence Error ode Error Message escription PL-00 PL-00 PL-00 PL ommunication Timeout (for single PL) %evice% PL ommunication Timeout (for multiple PLs, such as RS-/) NK received from PL STX is not found timeout occurred after sending a request to the PL %evice%. %evice% indicates the device name, such as EV00. Example error message for multiple PLs: EV00 PL ommunication Timeout negative acknowledgement (NK) control code has been generated during a read/write request. Start of Text (STX) control code was not found in the data packet received from the PL. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

204 hapter - Troubleshooting 0 No. Log Error Touch Panel Runtime Errors The -more touch panel includes built-in diagnostics that check for proper operation of the panel when it is running a project that has been transferred to its memory. Faults detected while the panel is running will produce a Runtime error. These errors are displayed in the upper left of the panel s display and are also recorded in the panel s error log. The error log can be viewed using the system setup screens. See hapter : System Setup Screens under the Information window to bring up the Error tab which includes a description of the logged data. detailed list and description of the various touch panel runtime errors can be found in ppendix : Touch Panel Runtime Errors. Touch Panel Runtime Errors example: Error Log ode RTE-00 RTE-00 Error Message Located at upper left of screen Error Message Tag Log Failed. SYS ERR Not enough Memory Space in %evice% ERROROE Log Failed. %evice% cannot be found SYS ERR ERROROE Tag Error ode Value System Screen Info > Error MM//YY HH/MM/SS Error ode RTE-00 MM//YY HH/MM/SS Error ode RTE-00 ause The size of the destination memory is not large enough to store the data. No device available or the device is defective. - E-USER-M Hardware User Manual, st Ed. Rev. G

205 hapter - Troubleshooting Panel onstantly isplays Initializing when Powering up If the touch panel constantly displays a message reading Initializing while powering up, then check the following possible causes..) -more supports US. and.0 memory devices. Ensure that the US device is. or.0 or backward compatible to support version.0.) The project that is loaded into the panel s internal SRM memory is corrupted. Either use the -more programming software to clear the panel s memory and re-transfer the project to the touch panel, or press the upper left corner of the touch panel screen while powering up to bypass the project and go directly to the System Setup Screen menu. Select the Memory menu, and use either the lear Memory or Set to Factory efault utility to clear the panel s memory and re-transfer the project to the touch panel. (see hapter - System Setup Screens).) n S memory card has been plugged into an S card slot and the S card either has no project stored on it or the project is corrupted. Remove the S memory card from the S card slot and either load the project to the panel s internal Flash memory, or re-format the S card using the S formatter available from Scard.org, or try a different S memory card. NOTE: In the Error Log you may find the error RTE-00 - heck Sum Error, which is defined as Memory in the panel has been corrupted by power loss, etc. If this is the case, try cycling power to the panel, re-transfer the project to the panel, and re-transfer the firmware, etc. in sequential steps to try to correct the problem. ata not Logging Problems If the data log is missing entries, or a Runtime Error for the Log Errors as shown in ppendix : Touch Panel Runtime Errors is seen, then check the following possible causes..) heck that the memory devices, that were selected for ata Storage under the -more programming software s Main Menu - Setup drop down - Panel Manager dialog box, are plugged into their proper location. larms, messages and screen captures can be independently selected to be saved to either a US pen drive plugged into the US Port - Type, or an S card plugged into S ard Slot or S ard Slot (-inch and -inch panels only)..) Ensure that the S card has been formatted with the S formatter provided by Scard. org..) The memory device could be bad. If possible, check it by plugging it into a P that has the ability to access the memory device. lso, not all US devices are compatible with the -more touch panels. Try using the utomationirect US Pen rive, p/n US-FLSH. heck System Screen, Memory for the presence of the US device inserted. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

206 hapter - Troubleshooting 0 Electrical Noise Problems Noise is one of the most difficult problems to diagnose. Electrical noise can enter a system in many different ways which fall into one of two categories, conducted or radiated. It may be difficult to determine how the noise is entering the system but the corrective actions for either of the types of noise problems are similar. onducted noise is when the electrical interference is introduced into the system by way of an attached wire, panel connection, etc. It may enter through a power supply connection, the communication ground connection, or the chassis ground connection. Radiated noise is when the electrical interference is introduced into the system without a direct electrical connection, much in the same manner as radio waves. While electrical noise cannot be eliminated, it can be reduced to a level that will not affect the system. Most noise problems result from improper grounding of the system. good earth ground can be the single most effective way to correct noise problems. If a ground is not available, install a ground rod as close to the system as possible. Ensure all ground wires are single point grounds and are not daisy chained from one device to another. Ground metal enclosures around the system. loose wire can act as a large antenna, introducing noise into the system. Therefore, tighten all connections in your system. Loose ground wires are more susceptible to noise than the other wires in your system. Review hapter : Installation & Wiring if you have questions regarding how to ground the touch panel. Electrical noise can enter the system through the power source for the touch panel. Installing a properly wired isolation transformer (neutral grounded) for all sources can help the problem, but only if wired correctly. sources should be well-grounded good quality supplies. Never run communication cables or low-voltage power wiring close to high voltage wiring or pulse generating wiring that controls such devices as solenoids, servos, VFs, etc. - E-USER-M Hardware User Manual, st Ed. Rev. G

207 Replacement Parts hapter In This hapter... Replacement Parts Overview...- Panel Mounting lip Replacements E-RK...- Logo Label Replacement Insert - E-LL...- -wire ommunications Terminal lock E-T...- Panel Power onnector Replacement E--ON...- Power dapter onnector Replacement E--ON...- Panel Gasket Replacements E-xx-GSK...- Gasket Replacement Installation Instructions:...-

208 0 hapter - Replacement Parts Replacement Parts Overview Part Number E-RK E-LL E-T E--ON E--ON E--GSK E--GSK E-0-GSK E-0W-GSK E--GSK E--GSK escription Panel mounting brackets, replacement, for -more E series touch panels. Package of brackets and screws. lank label insert for front bezel, replacement, for -more E series touch panels. Package of 0. -pole terminal block, replacement, for -wire RS communications port on -more E series panels. Package of. -terminal power connector, replacement, for -more E and E series touch panels -terminal power connector, replacement, for -more E and E series touch panels Panel mounting gasket, replacement, for -more E-TL -inch touch panel, NEM /X Panel mounting gasket, replacement, for -more E-TL -inch touch panel, NEM /X Panel mounting gasket, replacement, for -more E-T0L 0-inch touch panel, NEM /X Panel mounting gasket, replacement, for -more E-T0WL 0-inch touch panel, NEM /X Panel mounting gasket, replacement, for -more E-TL -inch touch panel, NEM /X Panel mounting gasket, replacement, for -more E-TL(-R) -inch and E-TL(-R) -inch touch panels, NEM /X - E-USER-M Hardware User Manual, st Ed. Rev. G

209 hapter - Replacement Parts Panel Mounting lip Replacements E-RK Spare panel mounting clips for E series -more touch panels. Package of clips with screws. Mounting lip Instructions. Position the touch panel through the cutout in the control cabinet door and hold in place. Position the mounting clips as appropriate for your model. Refer to hapter.. Tighten the mounting screws in an alternating fashion while observing the front of the touch panel. The goal is to make sure the front bezel is pulled up against the enclosure sheet metal uniformly, and the touch panel gasket is fully compressed all the way around its perimeter. Tighten the screws to a torque rating shown in the table below. void over-tightening the screws to the point that they start to deform or bend the bezel or mounting clip. Touch Panel Size,,, 0 & 0 Wide, Enclosure Thickness Range inch [ mm] inch [ mm]] Mounting lip Screw Torque Material - oz-in [ Nm] - 0 oz-in [ Nm] Metal 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

210 hapter - Replacement Parts 0 Logo Label Replacement Insert - E-LL 0. [.0] -more E series panels include one customizable logo label. dditional logo labels can be purchased in packs of 0. Installation - Insert E-LL into the slot in the side of the panel and lock tab into place.. [0.0] Units: inches [mm] Removal- Insert small tool such as a jewelers screwdriver and pull tab away from housing. - E-USER-M Hardware User Manual, st Ed. Rev. G

211 hapter - Replacement Parts -wire ommunications Terminal lock E-T able torque -more E series -wire communications terminal block replacement. One () terminal block is supplied with each touch panel. Tightening Torque minimum. lb-in (0. Nm) NOTE: Use 0 / copper conductors only, - WG Signal + Signal Logic Ground Port Tx Rx PU Port Rx Panel Power onnector Replacement E--ON -more touch panel -position power connector terminal block replacement. One () Power onnector is supplied with each touch panel. -ON Tightening Torque Power connector screw torque 0. oz-in (0. Nm) Power connector mounting torque oz-in (0. Nm) NOTE: Use 0 / copper conductors only, - WG + GN Recommended Supply Fuse Panel Size Rating p/n 0 &..0 ML- ML - V Equipment Ground Tx Port Tx Rx 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

212 hapter - Replacement Parts 0 Power dapter onnector Replacement E--ON -more power adapter -position power connector terminal block replacement. One () Power onnector is supplied with each / Power dapter, E-. E- Tightening Torque Power supply cable torque - oz-in ( Nm) Power connector mounting torque - oz-in ( Nm) Mounting flange screw torque - oz-in ( Nm) NOTE: Use 0 / copper conductors only, - WG 00-0 V 0/0 Hz Recommended Supply Fuse.0 time delay, p/n ML Power dapter Not recommended for use with the E-T when operating temperatures are expected to be above 0 deg. - E-USER-M Hardware User Manual, st Ed. Rev. G

213 hapter - Replacement Parts Panel Gasket Replacements E-xx-GSK Replacement NEM /X touch panel gaskets for -more,,, 0, and touch panels. Gasket Replacement Installation Instructions: Preparation: isconnect input power and all other connections, then remove the touch panel from the control cabinet. In a clean environment, place the panel face down on a lint-free soft surface to prevent scratching the front of the panel. Start at one corner and pull the old gasket out of the channel that holds the gasket in place. Pull the gasket up as you work around the entire perimeter of the touch panel. iscard the old gasket. Lay the new gasket over the channel so that the long and short sides of the gasket match up to the long and short sides of the touch panel. Start at one corner and match the gasket s corner to the channel s corner. Press the gasket into the channel and work all away around the perimeter of the touch panel. Re-install the touch panel. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

214

215 Panel and PL Error ode Tables ppendix In This ppendix... Introduction more Touch Panel Error ode Table... - irectlogi Panel Error ode PL- Explanation... - irectlogi K-Sequence Protocol PL Error ode Table... - irectlogi irectnet Protocol PL Error odes... - Modbus Protocols Error ode P Explanation... - utomationirect LIK... - utomationirect irectlogi - Modbus (Koyo)... - Modicon Modbus RTU... - Entivity Modbus RTU... - irectlogi EOM Protocol PL Error odes... - Productivity Error ode P... - utomationirect o-more Error odes... - llen-radley Panel Error ode PL- Explanation... - llen-radley F & H Protocols PL Error ode Tables llen-radley EtherNet/IP Protocol Panel Error ode PL-, and Explanation... - llen-radley EtherNet/IP Protocol PL Error ode Tables ontrollogix, ompactlogix, & FlexLogix... - llen-radley EtherNet/IP Protocol PL Error ode Tables... - Generic EtherNet IP Protocol PL Error odes... - GE 0-0 Panel Error ode PL- Explanation... - GE 0-0 SNPX Protocol PL Error ode Tables... - Mitsubishi FX Protocol PL Error odes... -

216 Panel and PL Error ode Tables ppendix Omron Panel Error ode PL- Explanation...- Omron Host Link Protocol PL Error ode Table...- Omron FINS Protocol PL Error ode Table...- Omron Panel Error ode P Explanation...- Omron S/J FINS Ethernet Protocol PL Error ode Table...- Siemens Panel Error ode P Explanation...-0 Siemens PPI Protocol PL Error ode Table...- Siemens ISO over TP Protocol PL Error ode Table...-

217 Panel and PL Error ode Tables ppendix This page intentionally left blank

218 ppendix - Panel and PL Error ode Tables 0 Introduction The -more family of touch panels is capable of communicating with a wide variety of Programmable Logic ontrollers. -more is capable of communicating over RS, RS and RS serial networks as well as Ethernet networks. It communicates with all utomationirect PLs utilizing various protocols. -more also communicates with other brands of PLs by their different protocols. For a complete list of PLs and protocols, see Step onnect Touch Panel to PL in hapter : Getting Started. s with any network communications, errors will occur. To make it more simple for the user to identify the cause of the possible error, we have provided a error code table for all of the possible errors that -more can detect. If a -more communications error does occur, the error message will appear across the top of the screen. The -more touch panel also monitors any errors that are generated by the various PLs that are connected to it. If any of the PL generated errors are detected, they are displayed across the top of the panel s display embedded as a hexadecimal value in error code P s message. n explanation of how the specific PL error is identified in the panel error code P is shown proceeding the specific manufacturer s PL error tables. How the hexadecimal error code value is interrupted is slightly different between manufacturers, so it is important to check the explanation at the beginning of each manufacturer s tables. NOTE: These PL error codes are provided by the manufacturer of the related PL and are subject to change by the PL manufacturer. Please refer to the manufacturers documentation for a more complete and up-to-date list of error codes. ll errors are also logged into the panel s Error log under the Information tab in the panel s System Setup Screens and are identified by the error code number. See hapter : System Setup Screens for additional details. If you have difficulty determining the cause of the error, please refer to hapter : Troubleshooting for some troubleshooting tips or contact our technical support H0-EOM/H0-EOM00 Ethernet Module L0 PL Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) Ethernet T able STX is not found -more Touch Panel -more Error Message uto MI / MI-X Ethernet Port - E-USER-M Hardware User Manual, st Ed. Rev. G

219 ppendix - Panel and PL Error ode Tables -more Touch Panel Error ode Table The following table includes all of the error codes and error messages that the panel will display if the listed cause is detected. ll of these errors involve problems that could result with the panel communicating with the connected PL. e aware that not all of the panel errors are used with each type of PL that can be connected to the panel. Error ode Error Message PL-00 PL-00 PL-00 PL-00 PL-00 PL-00 PL-00 PL ommunication Timeout (for single PL) %evice% PL ommunication Timeout (for multiple PLs, such as RS-/) NK received from PL EOT received from PL STX is not found ETX or ET is not found LR does not match R does not match -more Touch Panel Error ode Table ause timeout occurred after sending a request to the PL %evice%. %evice% indicates the device name, such as EV00. Example error message for multiple PLs: EV00 PL ommunication Timeout. negative acknowledgement (NK) control code has been generated during a read/write request. n End of Transmission (EOT) control code is sent by the PL in response to a Read/Write/Setit request.. Start of Text (STX) control code was not found in the data packet received from the PL. Neither an End of Text (ETX) nor an End of Transmission lock (ET) control code was found in the data packet received from the PL. There was an incorrect Longitudinal Redundancy heck (LR) control code in the communications packet received from the PL. This is an indication that the data in the packet is corrupted. There was an incorrect yclic Redundancy heck (R) control code in the communications packet received from the PL. This is an indication that the data in the packet is corrupted. PL-00 ddress does not match The address value returned in the data packet from the PL is incorrect. PL-00 ifferent function code received from PL The function code returned in the data packet from the PL is incorrect. PL-00 ata size does not match There are an incorrect number of bytes found in the data packet returned from the PL. PL-0 Invalid value in function code There is an invalid value in the function code. PL-0 Invalid command sent to PL There was an invalid command sent to the PL that wasn t recognized by the PL. PL-0 ENQ received from PL If the data packet does not include a negative acknowledgement (NK - 0x value) in the defined packet field, then an enquiry (ENQ) control code error will be displayed. PL-0 Transaction I does not match This error will be displayed if after checking the Transaction I ytes in the data packet, there is no match to what was requested. PL-0 %evice% No device found PL device designated as %evice% could not be found. PL-0 ata byte communication error 0 byte of data is recieved PL-0 Out of address range The touch panel requested a file number larger than. PL-0 Panel communication timeout The server panel did not respond when using the Panel Pass Through. PL-0 Found in parity error by hardware n error detected in the PL memory. PL-00 an t open serial port annot open the Serial Port. If this error shows on the panel, it indicates a hardware problem. PL-0 PL number does not match The PL number does not match the PL number configured. PL-0 an t reset Unable to reset the data communication bit. PL-0 able not connected properly ommunication cable incorrectly installed. -more Touch Panel Error ode Table continued on the next page. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

220 ppendix - Panel and PL Error ode Tables 0 -more Touch Panel Error ode Table (cont d) -more Touch Panel Error ode Table (cont d) Error ode Error Message ause PL-0 annot detect other devices on network The panel is not communicating with other devices on the network. PL-0 Panel not in polling list PL-0 PL connection timeout timeout occured after sending a request to the PL. PL-0 Memory type incorrect PL-0 PL failed to respond The PL failed to respond after sending a request to the PL. PL-0 MemVer ERR HMI x PLy When connected to a o-more PL the PL memory version must match the -more project PL memory version. Make sure that the PL project does not write into the memory version address. PL- Omron Ethernet Error n error code specific to Omron Ethernet with a Value of XXXX has been returned from the PL. See the explanation for error code PL- proceeding the Omron S/J FINS Ethernet error code tables. PL- Error code 0xaaaaaaaa returned from PL llen-radley EtherNET/IP specific. Encapsulation Error. See the explanation for error code PL- proceeding the llen- radley EtherNet/IP error code tables. PL- Error code 0xaaaaaaaa returned from PL llen-radley EtherNET/IP specific. IP Error. See the explanation for error code PL- proceeding the llen- radley EtherNet/IP error code tables. PL- Error code 0xaaaaaaaa returned from PL llen-radley EtherNET/IP specific. Service Packet Error. See the explanation for error code PL- proceeding the llen- radley EtherNet/IP error code tables. PL- Error code XXXX returned from PL n error code with a value of XXXX has been returned from the PL. See the explanation for error code PL- below for irect LOGI and proceeding each set of PL error code tables that use this error code. PL-00 annot write to Serial Port ata cannot write to the Serial port. ata was sent to the PL via the Serial Port. If this error shows on the Panel, it indicates a Hardware Problem. PL-00 Not enough buffer memory There was an error while allocating memory for the read buffer. When this error is displayed, a memory leak may have occurred. PL-0 ccess to inaccessible PL memory Request to inaccessible memory from the HMI layer to the PL protocol layer. This error is an indication that there is a problem in the HMI layer. PL-0 annot access by different function code Read/Write/Setit request has been sent to an invalid memory area. This error is an indication that there is a problem in the HMI layer. PL-0 Write request to PL Read Only Memory PL Write request was made to the PL s Read-Only memory area.this error is an indication that there is a problem in the HMI layer or the PL protocol layer. PL-0 ad device-access No device (PL) exists in the server panel or the device name does not match between the server and client when using the Panel Pass Through. PL-0 Protocol does not match The protocol for the device does Not match between the server and client when using the panel pass through. - E-USER-M Hardware User Manual, st Ed. Rev. G

221 ppendix - Panel and PL Error ode Tables irectlogi Panel Error ode PL- Explanation The PL- error code is used to show any errors that are generated by the connected PL. The PL- error message includes a four digit hexadecimal value embedded in the message. This value can be looked up in the specific PL s error tables to determine the cause of the error. The possible PL generated error codes for the irectlogi communication protocol are represented by a hexadecimal value as shown in the following message example. irect LOGI Error ode PL- Message Example: Error code 000 returned from PL Panel error code PL- showing a hexadecimal value of 000 indicates an Illegal data value dependent upon the request. PL error. irectlogi K-Sequence Protocol PL Error ode Table Panel Error ode PL- Hex Value 0F 00 0 The following table lists the errors that can be generated by the irectlogi PL when using the K-Sequence protocol. PL Error odes for irect LOGI K-Sequence escription Error setting value. Error in key mode - Set switch on PL PU to Term Password protected. NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. irectlogi irectnet Protocol PL Error odes Only errors as listed in the Touch Panel Error ode Table shown on page - can occur when using the irectlogi irectnet protocol, there are no PL generated errors. irectlogi error code tables continued on the next page. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

222 ppendix - Panel and PL Error ode Tables 0 Modbus Protocols Error ode P Explanation The following table lists the errors that can be generated by the Modbus protocols: utomationirect LIK utomationirect irectlogi - Modbus (Koyo) Modicon Modbus RTU Entivity Modbus RTU Panel Error ode P Hex Value 0x000 0x000 0x000 0x000 NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. Name ILLEGL FUNTION ILLEGL T RESS ILLEGL T VLUE SLVE EVIE FILURE PL Error odes Modbus Protocols Meaning The function code received in the query is not an allowable action for the server (or slave). This may be because the function code is only applicable to newer devices and was not implemented in the unit selected. It could also indicate that the server (or slave) is in the wrong state to process a request of this type, for example because it is unconfigured and is being asked to return registered values. The data address received in the query is not an allowable address for the server (or slave). More specifically, the combination of reference number and transfer length is invalid. For a controller with 00 registers, the PU addresses the first register as 0, and the last one as. If a request is submitted with a starting register address of and a quantity of registers of, then the request will successfully operate (address-wise at least) on registers,,,. If a request is submitted with a starting register of and a quantity of registers of, then the request will fail with Exception code 0x0 Illegal ata ddress since it attempts to operate on registers,,, and 00, and there is no register with address 00. value contained in the query data field is not an allowable value for server (or slave). This indicates a fault in the structure of the remainder of a complex request, such as that the implied length is incorrect. It specifically does NOT mean that a data item submitted for storage in a register has a value outside the expectation of the application program, since the Modbus protocol is unaware of the significance of any particular value of any particular register. n unrecoverable error occurred while the server (or slave) was attempting to perform the requested action. irectlogi EOM Protocol PL Error odes Only errors as listed in the Touch Panel Error ode Table shown previously in this ppendix can occur when using the irectlogi EOM protocol, there are no PL generated errors. - E-USER-M Hardware User Manual, st Ed. Rev. G

223 ppendix - Panel and PL Error ode Tables Productivity Error ode P Panel Error ode P Hex Value 0x000 0x000 0x000 0x000 NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Error odes for Productivity Meaning The function code received in the query is not an allowable action for the server (or slave). This may be because the function code is only applicable to newer devices and was not implemented in the unit selected. It could also indicate that the server (or slave) is in the wrong state to process a request of this type, for example because it is unconfigured and is being asked to return registered values. ddress out of range. heck to make sure that the -more tag and System I match the Productivity Programming Software Tag Name and System I. The project file in the Productivity system and the imported SV into -more must be in sync with each other. value contained in the query data field is not an allowable value for the server (or slave). This indicates a fault in the structure of the remainder of a complex request, such as that the implied length is incorrect. It specifically does NOT mean that a data item submitted for storage in a register has a value outside the expectation of the application program, since the Modbus protocol is unaware of the significance of any particular value of any particular register. n unrecoverable error occurred while the server (or slave) was attempting to perform the requested action. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

224 ppendix - Panel and PL Error ode Tables 0 utomationirect o-more Error odes PL Errors for o-more Error ode escription Resolution 0x0 Unknown ommand Should only occur if message has been corrupted or protocol version is mismatched. heck versions and update appropriately. If versions are correct, check cabling, routing and switches for bad packets. 0x0 Out of Sessions Too many devices connected to the PU. Reduce number of devices connected. 0x0 Illegal Operation Occurs when permission level is not sufficient for the operation performed by the panel. Increase the permission level to correct the problem. 0x0 Invalid Session Session number does match for sending device. Re-establish connection by power cycling or sending updated project. 0x0 Out of Range Invalid address exists. Ensure that address range is expanded and load configuration to the PU. 0x0 Invalid rgument Occurs when message cannot be parsed correctly. ould occur from noise or faulty wiring. 0x0 Program Update ctive Wait until program update is complete. 0x0 No Token Occurs when client attempts to update the project without first acquiring the program update token. 0x0 Program Update Inhibited Occurs when client attempts to update the project while ST is true. This allows the customer to programmatically prevent the project from being updated. 0x0 System onfiguration Update ctive Wait until System onfiguration update is complete to continue communications. 0x0 Invalid Mode Ensure that the switch on the PU is in Term mode. 0x0 Mode hange ctive Occurs when a PL mode change is attempted while a mode change is in progress. In some cases it takes several scans for a mode change. 0x0 Mode Locked Occurs when mode change is attempted and keyswitch is not in Term. 0x0E Invalid Password Enter o-more password in Password field of -more Panel Manager for this device. 0x0F Resource Locked Occurs when trying to update a tag that is forced. Force must be removed in order to update the tag. 0x00 oc Update ctive Occurs when someone attempts to access the documentation file while it is being written back to ROM. 0x0 Invalid river Occurs when attempting to read driver data from a driver that doesn t exist. 0x0 Invalid river ata Occurs when attempting to read a driver data type that isn t valid. 0x0 Shared RM write failed Occurs when attempting to read or write to a module s shared RM and it fails. Usually occurs when the module has gone bad. - E-USER-M Hardware User Manual, st Ed. Rev. G

225 ppendix - Panel and PL Error ode Tables llen-radley Panel Error ode PL- Explanation The PL- error code is used to show any errors that are generated by the connected PL. The PL- error message includes a four digit hexadecimal value embedded in the message. This value can be looked up in the specific PL s error tables to determine the cause of the error. The possible PL generated error codes for the llen-radley F and H communication protocols are represented by a hexadecimal value as shown in the following diagram. Please note that the error code is broken down into three sections. It is possible for more than one type of PL error to be displayed in this value. llen-radley Error ode PL- Message Example: F and H Protocol Error ode PL- reakdown -bit Word Remote - bits Local 0- bits EXT STS byte PL- Error ode Message isplayed Hexadecimal Value F 0 Example of an EXT STS error for a Type mismatch. hex Error code 00 returned from PL F and H Protocol Multiple Error ode Examples Example Example Example Remote - bits F x x x x x x F x x x Local 0- bits x 0 x x x x x x x x EXT STS byte x x 0 x x 0 0 x x 0 = = = Error PL- Value isplayed F F 0 Panel error code PL- showing a hexadecimal value of 00 indicates Illegal command or format. and Station is offline. PL errors. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

226 ppendix - Panel and PL Error ode Tables 0 llen-radley F & H Protocols PL Error ode Tables The following PL error code tables cover possible errors that are detected by the panel from llen-radley PLs using the F and H protocols. F includes full and half duplex communications for the MicroLogix 000, , 00, 00, SL /0, /0, /0, ontrollogix, ompactlogix and FlexLogix, and full duplex communications for the PL. H includes all MicroLogix and SL00 PL s and any communication connection using an llen-radley I device using the H protocol. NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Errors for llen-radley F and H Protocols, Local STS Errors (0- bits) Panel Error ode PL- Hex Value escription 0x0 Success; no error. 0x ST node is out of buffer space. 0x annot guarantee delivery; link layer. (The remote node specified does not K command.) 0x uplicate token holder detected. 0x Local port is disconnected. 0x pplication layer timed out waiting for response. 0x uplicate node detected. 0x Station is offline. 0x Hardware fault. PL Errors for llen-radley F and H Protocols, Remote STS Errors (- bits) Panel Error ode PL- Hex Value escription 0x0 Success; no error. 0x0 Illegal command or format. 0x0 Host has a problem and will not communicate. 0x0 Remote node host is missing, disconnected, or shut down. 0x0 Host could not complete function due to hardware fault. 0x0 ddressing problem or memory protect rungs. 0x0 Function not allowed due to command protection selection. 0x0 Processor is in Program Mode. 0x0 ompatibility mode file missing or communication zone problem. 0x0 Remote node cannot buffer command. 0x0 Wait K ( K buffer full). 0x0 Remote node problem due to download. 0x0 Wait K ( K buffer full). 0x0 not used 0xE0 not used 0xF0 Error code in the EXT STS byte. See the error code table on the next page. (PL generated error codes for the llen-radley F protocol continued on the next page.) -0 E-USER-M Hardware User Manual, st Ed. Rev. G

227 ppendix - Panel and PL Error ode Tables llen-radley F & H Protocols PL Error ode Tables (cont d) PL Errors for llen-radley F and H Protocols, EXT STS ommand ode for F0 ommand Panel Error ode PL- Hex Value escription 0x0 not used 0x field has an illegal value. 0x Fewer levels specified in address than minimum for any address. 0x More levels specified in address than system supports. 0x Symbol not found. 0x Symbol is of improper format. 0x ddress does not point to something usable. 0x File is wrong size. 0x annot complete request; situation has changed since start of the command. 0x ata or file size is too large. 0x Transaction size plus word address is too large. 0x ccess denied; improper privilege. 0x ondition cannot be generated; resource is not available. 0x ondition already exists; resource is readily available. 0xE ommand cannot be executed. 0xF Histogram overflow. 0x0 No access. 0x Illegal data type. 0x Invalid parameter or invalid data. 0x ddress reference exists to deleted area. 0x ommand execution failure for unknown reason; possible PL histogram overflow. 0x ata conversion error. 0x Scanner not able to communicate with rack adapter. 0x Type mismatch. 0x module response was not valid. 0x uplicated label. 0x Remote rack fault. 0x Timeout. 0x Unknown error. 0x File is open; another node owns it. 0x nother node is the program owner. 0x isk File is write protectid or otherwise unavailable 0x isk File is being used by another application. Update not performed (offline only). 0xE ata table element protection violation. 0xF Temporary internal problem. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

228 ppendix - Panel and PL Error ode Tables 0 llen-radley EtherNet/IP Protocol Panel Error ode PL-, and Explanation The PL-, PL-, and PL- error codes are used to show any errors that are generated by the connected PL. These error messages include an eight digit hexadecimal value displayed embedded in the message. This value can be looked up in the specific PL s error tables to determine the cause of the error. The possible PL generated error codes for the llen-radley EtherNet/IP communication protocol is represented by a hexadecimal value as shown in the following message example. llen-radley Error ode PL-,, Message Example: Error code returned from PL Panel error code PL- showing a hexadecimal value of indicates an The target received a message of invalid length. PL error. - E-USER-M Hardware User Manual, st Ed. Rev. G

229 ppendix - Panel and PL Error ode Tables llen-radley EtherNet/IP Protocol PL Error ode Tables ontrollogix, ompactlogix, & FlexLogix The following PL error code tables cover possible errors that are detected by the panel from llen-radley PLs using the EtherNet/IP protocol. This includes all ontrollogix, ompactlogix and FlexLogix PLs. NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Errors for llen-radley EtherNet/IP Protocol Encapsulation Errors (Error code 0xaaaaaaaa returned from the PL.) Panel Error ode PL- Hex Value escription 0x The sender issued an invalid or unsupported encapsulation command. 0x Insufficient memory resources in the receiver to handle the command. You can get this error if the -NET-ENI cannot connect to the PL serially. 0x Poorly formed or incorrect data in the data portion of the encapsulation message. 0x x Reserved for legacy (Rockwell utomation). 0x n orginator used an invalid session handle when sending an encapsulation message to the target. 0x The target received a message of invalid length. 0x x Reserved for legacy (Rockwell utomation). 0x Unsupported encapsulation protocol revision. 0x000000a - 0x0000ffff Reserved for future expansion. Panel Error ode PL- Hex Value 0x0000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 0x00 0x00 0x00 0x00 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaaaaaaaa returned from the PL.) escription onnection Manager: onnection in Use or uplicate Forward Open. onnection Manager: Transport lass and Trigger combination not supported. onnection Manager: Ownership onflict. onnection Manager: onnection not found at target application. onnection Manager: Invalid connection type (problem with type or priority). onnection Manager: Invalid connection size. onnection Manager: evice not configured. onnection Manager: RPI not supported. ould also be problem with inactivity timeout. onnection Manager: onnection Manager cannot support any more connections. onnection Manager: Either the vendor I or the Product ode in the key segment did not match the device. onnection Manager: Product Type in the key segment did not match the device. onnection Manager: Major or minor revision information in the key segment did not match the device. (PL generated error codes for the llen-radley EtherNet/IP protocol for ontrollogix, ompactlogix, and FlexLogix continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

230 ppendix - Panel and PL Error ode Tables 0 llen-radley EtherNet/IP Protocol PL Error ode Tables ontrollogix, ompactlogix, & FlexLogix (cont d) Panel Error ode PL- Hex Value 0x00 0x00 0x00 0x00a 0x00b 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00a 0x00b 0x00c 0x00d 0x00e 0x00f 0x000-0x00ff 0x x x x x x00000 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaaaaaaaa returned from the PL.) escription onnection Manager: Invalid connection point. onnection Manager: Invalid configuration format. onnection Manager: onnection request fails since there is no controlling connection currently open. onnection Manager: Target application cannot support any more connections. onnection Manager: RPI is smaller than the Production Inhibit Time. onnection Manager: onnection cannot be closed since the connection has timed out. onnection Manager: Unconnected Send timed out waiting for a response. onnection Manager: Parameter error in Unconnected send service. onnection Manager: Message too large for Unconnected message service. onnection Manager: Unconnected acknowledge without reply. onnection Manager: No buffer memory available. onnection Manager: Network andwidth not available for data. onnection Manager: No Tag filters available. onnection Manager: Not configured to send real-time data. onnection Manager: Port specified in Port segment not available. onnection Manager: Link address specified in port segment not available. onnection Manager: invalid segment type or segment value in path. onnection Manager: Path and onnection not equal in close. onnection Manager: Ether Segment not present or Encoded Value in Network Segment is invalid. onnection Manager: Link address to self invalid. onnection Manager: Resources on Secondary unavailable. onnection Manager: onnection already established. onnection Manager: irect connection already established. onnection Manager: Miscellaneous. onnection Manager: Redundant connection mismatch. onnection Manager: No more consumer resources available in the producing module. onnection Manager: No connection resources exist for target path. onnection Manager: Vendor specific. Resource unavailable: onnection Manager resources are unavailable to handle service request. Invalid parameter value. Path segment error: The path segment identifier or the segment syntax was not understood by the processing node. Path destination unknown: The path is referencing an object class, instance or structure element that is not known or is not contained in the processing node. Partial transfer: Only part of the expected data was transferred. onnection lost: The messaging connection was lost. (PL generated error codes for the llen-radley EtherNet/IP protocol for ontrollogix, ompactlogix, and FlexLogix continued on the next page.) - E-USER-M Hardware User Manual, st Ed. Rev. G

231 ppendix - Panel and PL Error ode Tables llen-radley EtherNet/IP Protocol PL Error ode Tables ontrollogix, ompactlogix, & FlexLogix (cont d) Panel Error ode PL- Hex Value 0x x x0a0000 0x0b0000 0x0c0000 0x0d0000 0x0e0000 0x0f0000 0x x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xa0000 0xb0000 0xc0000 0xd0000 0xe0000 0xf0000 0x x0000 0x0000 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaaaaaaaa returned from the PL.) escription Service not supported: The requested service was not implemented or was not defined for this Object lass/instance. Invalid attribute value: Invalid attribute data detected. ttribute list error: n attribute in the Get_ttribute_List or Set_ttribute_List response has a non-zero status. lready in requested mode/state: The object is already in the mode/state being requested by the service. Object state conflict: The object cannot perform the requested service in its current mode/state. Object already exists: The requested instance of object to be created already exists. ttribute not settable: request to modify non-modifiable attribute was received. Privilege violation: permission/privilege check failed. evice state conflict: The device s current mode/state prohibits the execution of the requested service. Reply data too large: The data to be transmitted in the response buffer is larger than the allocated response buffer. Fragmentation of a primitive value: The service specified an operation that is going to fragment a primitive data value. For example, trying to send a byte value to a REL data type ( byte). Not enough data: The service did not supply enough data to perform the specified operation. ttribute not supported: The attribute specified in the request is not supported. Too much data: The service supplied more data than was expected. Object does not exist: The object specified does not exist in the device. Service fragmentation sequence not in progress: The fragmentation sequence for this service is not currently active for this data. No stored attribute data: The attribute data of this object was no saved prior to the requested service. Store operation failure: The attribute data of this object was not saved due to a failure during the attempt. Routing failure, request packet too large: The service request packet was too large for transmission on a network in the path to the destination. Routing failure, response packet too large: The service reponse packet was too large for transmission on a network in the path from the destination. Missing attribute list entry data: The service did not supply an attribute in a list of attributes that was needed by the service to perform the requested behavior. Invalid attribute value list: The service is returning the list of attributes supplied with status information for those attributes that were invalid. Embedded service error: See Service Packet error list (PL- Error codes) below: Vendor specific error: vendor specific error has been encountered. This occurs when none of the specified errors relate to the error in the device. Invalid parameter: parameter associated with the request was invalid. This code is used when a parameter does meet the requirements defined in an pplication Object specification. Write-once value or medium already written: n attempt was made to write to a write-once-medium that has already been written or to modify a value that cannot be change once established. Invalid Reply Received: n invalid reply is received (example: service code sent doesn t match service code received.). (PL generated error codes for the llen-radley EtherNet/IP protocol for ontrollogix, ompactlogix and FlexLogix continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

232 ppendix - Panel and PL Error ode Tables 0 llen-radley EtherNet/IP Protocol PL Error ode Tables ontrollogix, ompactlogix, & FlexLogix (cont d) Panel Error ode PL- Hex Value 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xa0000 0xb0000-0xcf0000 0xd xff0000 Panel Error ode PL- Hex Value 0x x x x0a0000 0x0000 0xc0000 0x0000 0xff0 0xff0 0xff0 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaaaaaaaa returned from the PL.) escription Reserved by IP for future extensions. Reserved by IP for future extensions. Key failure in path: The key segment was included as the first segment in the path does not match the destination module. The object specific status shall indicate which part of the key check failed. Path Size Invalid: The size of the path which was sent with the Service Request is either not large enough to allow the Request to be routed to an object or too much routing data was included. Unexpected attribute in list: n attempt was made to set an attribute that is not able to be set at this time. Invalid Member I: The Member I specified in the request does not exist in the specified lass/instance/ ttribute. Member not settable: request to modify a non-modifiable member was received. Group only server general failure: This error code may only be reported by evicenet group only servers with K or less code space and only in place of Service not supported, ttribute not supported and ttribute not settable. Reserved by IP for future extensions. Reserved for Object lass and service errors: This range of error codes is to be used to indicate Object lass specific errors. Use of this range should only be used when errors in this table don t accurately reflect the error encountered. PL Errors for llen-radley EtherNet/IP Protocol Service Packet Errors (Error code 0xaaaaaaaa returned from the PL.) escription This general status codes that the tag name could not be deciphered. This could mean that the tag name was entered incorrectly or does not exist in the PL. The particular item referenced (usually instance) could not be found. The amount of data requested would not fit into the response buffer. Partial data transfer has occurred. n error has occurred trying to process one of the attributes. Not enough command data/parameters were supplied in the command to execute the service requested. n insufficient number of attributes were provided compared to the attribute count. The tag name length specified did not match what was in the message. You have tried to access beyond the end of the data object. The abbreviated type does not match the data type of the data object. The beginning offset was beyond the end of the template. - E-USER-M Hardware User Manual, st Ed. Rev. G

233 ppendix - Panel and PL Error ode Tables llen-radley EtherNet/IP Protocol PL Error ode Tables The following PL error code tables cover possible errors that are detected by the panel from llen-radley PLs using the EtherNet/IP protocol. This includes MicroLogix 00, 00 & SL /0, both using their native Ethernet port, and MicroLogix 000, 00, 00, 00, 00, SL /0, /0 and /0 using an llen-radly ENI dapter. NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Errors for llen-radley EtherNet/IP Protocol Encapsulation Errors (Error code 0xaaaaaaaa returned from the PL.) Panel Error ode PL- Hex Value escription 0x The sender issued an invalid or unsupported encapsulation command. 0x Insufficient memory resources in the receiver to handle the command. You can get this error if the -NET-ENI cannot connect to the PL serially. 0x Poorly formed or incorrect data in the data portion of the encapsulation message. 0x x Reserved for legacy (Rockwell utomation). 0x n orginator used an invalid session handle when sending an encapsulation message to the target. 0x The target received a message of invalid length. 0x x Reserved for legacy (Rockwell utomation). 0x Unsupported encapsulation protocol revision. 0x000000a - 0x0000ffff Reserved for future expansion. Panel Error ode PL- Hex Value 0x0000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaabbbb returned from the PL.) escription onnection Manager: onnection in Use or uplicate Forward Open. onnection Manager: Transport lass and Trigger combination not supported. onnection Manager: Ownership onflict. onnection Manager: onnection not found at target application. onnection Manager: Invalid connection type (problem with type or priority). onnection Manager: Invalid connection size. onnection Manager: evice not configured. onnection Manager: RPI not supported. ould also be problem with inactivity timeout. (PL generated error codes for the llen-radley EtherNet/IP protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

234 ppendix - Panel and PL Error ode Tables 0 llen-radley EtherNet/IP Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00a 0x00b 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00a 0x00b 0x00c 0x00d 0x00e 0x00f 0x000-0x00ff PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaabbbb returned from the PL.) escription onnection Manager: onnection Manager cannot support any more connections. onnection Manager: Either the vendor I or the Product ode in the key segment did not match the device. onnection Manager: Product Type in the key segment did not match the device. onnection Manager: Major or minor revision information in the key segment did not match the device. onnection Manager: Invalid connection point. onnection Manager: Invalid configuration format. onnection Manager: onnection request fails since there is no controlling connection currently open. onnection Manager: Target application cannot support any more connections. onnection Manager: RPI is smaller than the Production Inhibit Time. onnection Manager: onnection cannot be closed since the connection has timed out. onnection Manager: Unconnected Send timed out waiting for a response. onnection Manager: Parameter error in Unconnected send service. onnection Manager: Message too large for Unconnected message service. onnection Manager: Unconnected acknowledge without reply. onnection Manager: No buffer memory available. onnection Manager: Network andwidth not available for data. onnection Manager: No Tag filters available. onnection Manager: Not configured to send real-time data. onnection Manager: Port specified in Port segment not available. onnection Manager: Link address specified in port segment not available. onnection Manager: invalid segment type or segment value in path. onnection Manager: Path and onnection not equal in close. onnection Manager: Ether Segment not present or Encoded Value in Network Segment is invalid. onnection Manager: Link address to self invalid. onnection Manager: Resources on Secondary unavailable. onnection Manager: onnection already established. onnection Manager: irect connection already established. onnection Manager: Miscellaneous. onnection Manager: Redundant connection mismatch. onnection Manager: No more consumer resources available in the producing module. onnection Manager: No connection resources exist for target path. onnection Manager: Vendor specific. (PL generated error codes for the llen-radley EtherNet/IP protocol continued on the next page.) - E-USER-M Hardware User Manual, st Ed. Rev. G

235 ppendix - Panel and PL Error ode Tables llen-radley EtherNet/IP Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0x x x x x x x x x0a0000 0x0b0000 0x0c0000 0x0d0000 0x0e0000 0x0f0000 0x x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xa0000 0xb0000 0xc0000 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaabbbb returned from the PL.) escription Resource unavailable: onnection Manager resources are unavailable to handle service request. Invalid parameter value. Path segment error: The path segment identifier or the segment syntax was not understood by the processing node. Path destination unknown: The path is referencing an object class, instance or structure element that is not known or is not contained in the processing node. Partial transfer: Only part of the expected data was transferred. onnection lost: The messaging connection was lost. Service not supported: The requested service was not implemented or was not defined for this Object lass/instance. Invalid attribute value: Invalid attribute data detected. ttribute list error: n attribute in the Get_ttribute_List or Set_ttribute_List response has a non-zero status. lready in requested mode/state: The object is already in the mode/state being requested by the service. Object state conflict: The object cannot perform the requested service in its current mode/state. Object already exists: The requested instance of object to be created already exists. ttribute not settable: request to modify non-modifiable attribute was received. Privilege violation: permission/privilege check failed. evice state conflict: The device s current mode/state prohibits the execution of the requested service. Reply data too large: The data to be transmitted in the response buffer is larger than the allocated response buffer. Fragmentation of a primitive value: The service specified an operation that is going to fragment a primitive data value. For example, trying to send a byte value to a REL data type ( byte). Not enough data: The service did not supply enough data to perform the specified operation. ttribute not supported: The attribute specified in the request is not supported. Too much data: The service supplied more data than was expected. Object does not exist: The object specified does not exist in the device. Service fragmentation sequence not in progress: The fragmentation sequence for this service is not currently active for this data. No stored attribute data: The attribute data of this object was no saved prior to the requested service. Store operation failure: The attribute data of this object was not saved due to a failure during the attempt. Routing failure, request packet too large: The service request packet was too large for transmission on a network in the path to the destination. Routing failure, response packet too large: The service reponse packet was too large for transmission on a network in the path from the destination. Missing attribute list entry data: The service did not supply an attribute in a list of attributes that was needed by the service to perform the requested behavior. (PL generated error codes for the llen-radley EtherNet/IP protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

236 ppendix - Panel and PL Error ode Tables 0 llen-radley EtherNet/IP Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0xd0000 0xe0000 0xf0000 0x x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xa0000 0xb0000-0xcf0000 0xd xff0000 PL Errors for llen-radley EtherNet/IP Protocol IP Errors (Error code 0xaabbbb returned from the PL.) escription Invalid attribute value list: The service is returning the list of attributes supplied with status information for those attributes that were invalid. Embedded service error: See Service Packet error list (PL- Error codes) below: Vendor specific error: vendor specific error has been encountered. This occurs when none of the specified errors relate to the error in the device. Invalid parameter: parameter associated with the request was invalid. This code is used when a parameter does meet the requirements defined in an pplication Object specification. Write-once value or medium already written: n attempt was made to write to a write-once-medium that has already been written or to modify a value that cannot be change once established. Invalid Reply Received: n invalid reply is received (example: service code sent doesn t match service code received.). Reserved by IP for future extensions. Reserved by IP for future extensions. Key failure in path: The key segment was included as the first segment in the path does not match the destination module. The object specific status shall indicate which part of the key check failed. Path Size Invalid: The size of the path which was sent with the Service Request is either not large enough to allow the Request to be routed to an object or too much routing data was included. Unexpected attribute in list: n attempt was made to set an attribute that is not able to be set at this time. Invalid Member I: The Member I specified in the request does not exist in the specified lass/instance/ ttribute. Member not settable: request to modify a non-modifiable member was received. Group only server general failure: This error code may only be reported by evicenet group only servers with K or less code space and only in place of Service not supported, ttribute not supported and ttribute not settable. Reserved by IP for future extensions. Reserved for Object lass and service errors: This range of error codes is to be used to indicate Object lass specific errors. Use of this range should only be used when errors in this table don t accurately reflect the error encountered. (PL generated error codes for the llen-radley EtherNet/IP protocol continued on the next page.) -0 E-USER-M Hardware User Manual, st Ed. Rev. G

237 ppendix - Panel and PL Error ode Tables llen-radley EtherNet/IP Protocol PL Error ode Tables (cont d) PL Errors for llen-radley EtherNet/IP Protocol Service Packet Errors (Error code 0xaabbbb returned from the PL.) Panel Error ode PL- Hex Value escription 0x00000 ST Node is out of buffer space. 0x00000 annot guarantee delivery; link layer (The remote node specified does not K command). 0x00000 uplicate token holder detected. 0x00000 Local port is disconnected. 0x00000 pplication layer timed out waiting for response. 0x00000 uplicate node detected. 0x00000 Station is offline. 0x00000 Hardware fault. 0x00000 Illegal command or format. Typical error received from PL when addressed requested to the PL does not exist. Usually occurs if memory map has not been expanded in PL to the range requested from panel. 0x00000 Host has a problem and will not communicate. 0x00000 Remote node host is missing, disconnected, or shut down. 0x00000 Host could not complete function due to hardware fault. 0x00000 ddressing problem or memory protected rungs. 0x00000 Function not allowed due to command protection selection. 0x00000 Processor is in Program Mode. 0x00000 ompatibility mode file missing or communication zone problem. 0x00000 Remote node cannot buffer command. 0x00000 Wait K ( K buffer full). 0x00000 Not used. 0x00000 Not used. 0x00000 Error code in the EXT STS byte. See the error code table below. 0xE00000 Fewer levels specified in address than minimum for any address. 0xF0000 More levels specified in address than system supports. 0xF0000 Symbol not found. 0xF0000 Symbol is of improper format. 0xF0000 ddress does not point to something usable. 0xF0000 File is wrong size. 0xF0000 annot complete request, situation has changed since start of the command. 0xF0000 ata or file size is too large. 0xF0000 Transaction size plus word address is too large. 0xF0000 ccess denied; improper privilege. This will occur if data file is set to constant or protected. 0xF0000 ondition cannot be generated; resource is not available. 0xF0000 ondition already exists; resource is readily available. (PL generated error codes for the llen-radley EtherNet/IP protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

238 ppendix - Panel and PL Error ode Tables 0 llen-radley EtherNet/IP Protocol PL Error ode Tables (cont d) PL Errors for llen-radley EtherNet/IP Protocol Service Packet Errors (Error code 0xaabbbb returned from the PL.) Panel Error ode PL- Hex Value escription 0xF00E00 ommand cannot be executed. 0xF00F00 Histogram overflow. 0xF0000 No access. 0xF000 Illegal data type. 0xF000 Invalid parameter or invalid data. 0xF000 ddress reference exists to deleted area. 0xF000 ommand execution failure for unknown reason; possible histogram overflow. 0xF000 ata conversion error. 0xF000 Scanner not able to communicate with rack adapter. 0xF000 Type mismatch. 0xF000 module response was not valid. 0xF000 uplicated label. 0xF000 Remote rack fault. 0xF000 Timeout. 0xF000 Unknown error. 0xF000 File is open; another node owns it. 0xF000 nother node is the program owner. 0xF000 Reserved. 0xF000 Reserved. 0xF0E00 ata table element protection violation. 0xF0F00 Temporary internal problem. Generic EtherNet IP Protocol PL Error odes Only errors as listed in the Touch Panel Error ode Table shown previously in this ppendix can occur when using the Generic Ethernet IP protocol, there are no PL generated errors. - E-USER-M Hardware User Manual, st Ed. Rev. G

239 ppendix - Panel and PL Error ode Tables GE 0-0 Panel Error ode PL- Explanation The PL- error code is used to show any errors that are generated by the connected PL. The PL- error message includes a four digit hexadecimal value embedded in the message. This value can be looked up in the specific PL s error tables to determine the cause of the error.the possible PL generated error codes for the GE 0-0 communication protocol are represented by a hexadecimal value as shown in the following message example. GE 0-0 Error ode PL- Message Example: Error code 00 returned from PL Panel error code PL- showing a hexadecimal value of 00 indicates an Port configurator error. PL error. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

240 ppendix - Panel and PL Error ode Tables 0 GE 0-0 SNPX Protocol PL Error ode Tables The following table lists the errors that can be generated by the GE 0-0 PL when using the SNPX protocol. Panel Error ode PL- Hex Value No error 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000E 0x000F 0x00 0x000 0x00 0x00 0x00 0x00 0x00 NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Errors for GE 0-0 SNPX Protocol (Major) escription Successful completion. (This is the expected completion value in the OMMREQ Status Word.) Insufficient Privilege. For Series 0-0 PL, the minor error code contains the privilege level required for the service request. Protocol Sequence Error. The PU has received a message that is out of order. Service Request Error, the minor error code contains the specific error code. Illegal Mailbox Type. Service request mailbox type is either undefined or unexpected. The PL PU s Service Request Queue is full. The master should retry later. It is recommended that the master wait a minimum of 0 msec before sending another service request. SNP OS river Error. The minor error code contains the specific error code. Illegal Service Request. The requested service is either not defined or not supported. (This value is returned in lieu of the actual 0h value passed in the SNP error message, to avoid confusion with the normal successful OMMREQ completion.) Local SNP/SNP-X Error. n error occurred within the SNP task in the MM module in this PL. This error may occur in either an SNP master or an SNP slave. The minor error code contains the specific error code. Remote SNP Error. n error occurred within the SNP slave task in the MM module in the remote PL. The minor error code contains the specific error code. utodial Error. n error occurred while attempting to send a command string to an attached external modem. The minor error code contains the specific error code. SNP-X slave error. n error occurred within the SNPX task in the remote slave device. The minor error code contains the specific error code. Port configurator error. Problem with sending mail to the slave Service Request task. (Series 0-0 PL PUs only) Problem with getting mail from the slave Service Request task. (Series 0-0 PL PUs only) Slave SNP task timed out before receiving an SRP response. (Series 0-0 PL PUs only) Slave SNP task could not find the requested datagram connection. (Series 0-0 PL PUs only) Slave SNP task encountered an error in trying to write the datagram. (Series 0-0 PL PUs only) Slave SNP task encountered an error in trying to update the datagram. (Series 0-0 PL PUs only) (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) - E-USER-M Hardware User Manual, st Ed. Rev. G

241 ppendix - Panel and PL Error ode Tables GE 0-0 SNPX Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Error 0x0 PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Error 0x0 PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Error 0x0 PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Error 0x0 PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Error 0x00 PL Error 0x00E PL Error 0x00F PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) escription WIT-type OMMREQ is not permitted; must use NOW IT-type. Not used The service request code in an X-Request message is unsupported or invalid at this time. This error may occur if an SNP-X communication session has not been success fully established at the slave device. OMMREQ command is not supported. The modem command string length exceeds 0 characters. Insufficient privilege level in the slave PL PU for the requested SNP-X service. Password protection at PL PU may be preventing the requested service. Unsupported OMMREQ. These errors are only generated when there is no protocol currently being run on a port, and the port receives a OMMREQ. (The port may be disabled or an error has occurred in processing a new configuration). SNP communication is not active. Must initiate a new SNP communication by sending an ttach or Long ttach OMMREQ. OMMREQ ata lock Length is too small. Output command string data is missing or incomplete. Invalid slave memory type in X-Request message. Invalid OMMREQ length. SNP slave did not respond to ttach message from master. Serial output timeout. The MM module was unable to transmit the modem autodial output from the serial port. (May be due to missing TS signal when the MM is configured to use hardware flow control.) Invalid slave memory address or range in X-Request message. Invalid OMMREQ status word location. Unable to write SNP Status Word to local PL memory; may be due to invalid Status Word memory type or address. Response was not received from modem. heck modem and cable. Invalid data length in X-Request message. ata length must be non-zero, and may not exceed decimal 000 bytes. Invalid OMMREQ data. Master device memory type is not valid in this PL. Modem responded with USY. Modem is unable to complete the requested connection. The remote modem is already in use; retry the connection request at a later time. X-uffer data length does not match the service request in X-Request message. The X-uffer message length is obtained from the Next Message Length field in the X-Request message; the length of the data within the buffer message is always the message length. Master device memory address or length is zero. Modem responded with NO RRIER. Modem is unable to complete the requested connection. heck the local and remote modems and the telephone line. Queue Full indication from Service Request Processor in slave PL PU. The slave is temporarily unable to complete the service request. The master should try again later. It is recommended that the master wait at least 0 msec before repeating the X-Request. (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

242 ppendix - Panel and PL Error ode Tables 0 GE 0-0 SNPX Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0x00 0x00E 0x00F 0x00 PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) escription Unable to read or write master device memory locations specified in OMMREQ. Usually caused by invalid memory address for this PL. SNP message exchange may have taken place. Modem responded with NO ILTONE. Modem is unable to complete the requested connection. heck the modem connections and the telephone line. Service Request Processor response exceeds 000 bytes; the SNP-X slave device cannot return the data in an X-Response message. (This error applies to MM module only.) Master device memory data length exceeds maximum data size of MM module (0 bytes). Must use a smaller data length. Use multiple OMMREQs if total data length exceeds this maximum value. 0x00E Modem responded with ERROR. Modem is unable to complete the requested command. heck the modem command string and modem. 0x00 Slave device memory type is missing or not valid. 0x00E Modem responded with RING, indicating that the modem is being called by another modem. Modem is unable to complete the requested command. Retry the modem command at a later time. 0x00 Slave device memory address is missing or zero. n unknown response was received from the modem. Modem is unable to complete the requested 0x00E command. heck the modem command string and modem. The modem response is expected to be either ONNET or OK. OMMREQ ata lock Length is too small. 0x00 (When expected OMMREQ length is words or less. n improper length may cause other minor error codes -.) 0x00 Invalid iagnostic Status Word (SW) starting word or length. 0x0E0 Invalid maximum SNP message data size. Must be an even value from to 0. 0x0F0 Invalid Privilege Level. Must be 0 through or -. 0x00 Invalid Fault Table selector. Must be for I/O Fault Table, or for PL Fault Table. Unexpected Service Request Processor error. 0x00F (This error applies to MM module only; the unexpected SRP error code is saved in the iagnostic Status Words in the MM module.) 0x0 Invalid Fault Table starting index. Must be - for I/O Fault Table, or - for PL. 0x0 Invalid fault count. Must be - for I/O Fault Table, or - for PL Fault Table. 0x0 Invalid Set PL ate/time mode. Must be -. 0x0 Invalid Set PL ate/time date, time, or day-of-week value. 0x0 Unable to retrieve master device PL time/date from PL PU. 0x0F Requested service is not permitted in a roadcast request. The master must direct the X-Request message to a specific SNP-X slave device. 0x0 Invalid slave PL type. Must be 0 for Series 0-0, or for Series 0-0 or Series x0 Invalid datagram type. Must be 0h for normal datagram, or h () for permanent datagram. 0x0 Missing or too many datagram point formats. Must be -. 0x0 Invalid datagram point format data. (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) - E-USER-M Hardware User Manual, st Ed. Rev. G

243 ppendix - Panel and PL Error ode Tables GE 0-0 SNPX Protocol PL Error ode Tables (cont d) PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) Panel Error ode PL- Hex Value escription 0x0 atagram area size is too small to include data for all specified point formats. 0x0 Invalid number of ontrol Program Names. Must be -. 0x0 SNP-X Request exceeds maximum data size (000 bytes). Must use a smaller data length. Use multiple OMMREQs if necessary. 0x0 Invalid SNP-X communication session type. Must be 0 for a single slave device, or for multiple slave devices. Illegal destination SNP I specified for SNP-X slave. Must be 0- SII characters, plus a terminating 0xE0 null character (00h). The Null SNP I (eight bytes of 00h) may be used to specify any single device. The roadcast SNP I (eight bytes of FFh) may be use to specify all slave devices on the serial link. estination SNP I does not match SNP-X session type. 0xF0 The roadcast SNP I is not permitted in a single-slave SNP-X session. The Null SNP I is not permitted in a multiple-slave SNP-X session. 0x00 Inactivity timeout (T ). The SNP slave has not received any new SNP messages within the configured T time interval. 0x00F Invalid Message Type field in a received X-Request message. The message type of an X-Request message must be h = X. 0x0 Parity error has occurred on an ttach, ttach Response, or Update Real time atagram message. ommunications have not been established. Invalid Next Message Type or Next Message Length field in a received X Request message. If this request does not use a buffer (0- bytes of data), the Next Message Type must be zero. If this request will be 0x0F followed with a buffer message (more than byte.)), the Next Message Type must be h = T, and the Next Message Length must specify the length of the X-uffer message. Valid X-uffer message lengths are -00 bytes (data length plus bytes). 0x0 (lock heck ode) error has occurred on an ttach, ttach Response, or Update Realtime atagram message. ommunications have not been established. 0x0F Invalid Message Type field in a received X-uffer message. The message type of an X-uffer message must be h = T. 0x0 Framing or Overrun serial error has occurred on an ttach, ttach Response, or Update Realtime atagram message. ommunications have not been established. 0x0F Invalid Next Message Type field in a received X-uffer message. Since an X-uffer message is never followed by another message, the Next Message Type must always be zero. 0x0 n invalid SNP message type was received when an ttach, ttach Response, or Update Realtime atagram message was required. ommunications have not been established. 0x0 n invalid next message length value was specified in an ttach, ttach Response, or Update Realtime atagram message. ommunications have not been established. 0x0 n unexpected SNP message type was received when an ttach, ttach Response, or Update Realtime atagram was required. ommunications have not been established. 0x0 nother reak was received while SNP slave was waiting for an ttach or Update Realtime atagram message. n SNP message has been sent and retried the maximum number of times. 0x0 maximum of two retries are permitted. retry is caused by a NK from from the remote SNP device. 0x0 received SNP message has been NKed the maximum number of two times. The NKed message may be retransmitted a maximum of two times. (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

244 ppendix - Panel and PL Error ode Tables 0 GE 0-0 SNPX Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0x0 0x0 0x0 0x0 0xE0 0xF0 0x00 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x00 0x00 0x00F PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) escription n unknown message was received when an acknowledge (K or NK) was required. Sequence Error. n unexpected SNP message type was received. Received SNP message contains bad next message length value. cknowledge timeout. n acknowledge (K or NK) was not received within the configured T time interval. slave device may generate this error if the master device has aborted after maximum response NKs and does not NK the next response retry. Response timeout. The SNP Master did not receive an SNP Response message within the configured T time interval. uffer message timeout. n expected Text uffer or onnection ata message was not received within the configured T time interval. Serial output timeout. The MM module was unable to transmit a reak, an SNP message, or SNP acknowledge (K or NK) from the serial port. (May be due to missing TS signal when the MM module is configured to use hardware flow control.) SNP slave did not receive a response from the Service Request Processor in the PL PU. OMMREQ timeout. The OMMREQ did not complete within the configured time interval. n SNP Request or Response was aborted prior to completion due to reception of a reak. PL backplane communications error Invalid Piggyback Status data memory type or address. ommunications have not been established. Invalid SNP Slave SNP I. Must be a 0- SII characters, plus a terminating null character (00h). The Null SNP I (eight bytes of 00h) may be used to specify any single slave device. The SNP master has received a response message containing an unexpected data length. Usually indicates a problem with the remote SNP slave device. May occur when Series 0-0 commands (Task Memory or Program lock Memory Read/Write) are issued to a Series 0-0 slave device. Response code in received SNP-X response message does not match expected value. (Response code must equal the request code +0h.) SNP-X Response message exceeds maximum data size (decimal 000 bytes). ata in the Response is ignored. parity error has occurred on an X-ttach Response message when establishing a new SNP-X communication session. ommunications have not been established. The requested service is not supported by the SNP slave. Serial output timeout. The slave was unable to transmit an SNP-X message from the serial port. (May be due to missing TS signal when the MM module is configured to use hardware flow control.) (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) - E-USER-M Hardware User Manual, st Ed. Rev. G

245 ppendix - Panel and PL Error ode Tables GE 0-0 SNPX Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0x0 0x0 0x0F 0x0 0x0 0x0F 0x0 0x0 0x0F 0x0 0x0 0x0F 0x0 0x0 0x00 0x00F 0x0 0x0F 0x0 0x0F PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) escription framing or overrun error has occurred on an X-ttach Response message when establishing a new SNP-X communication session. ommunications have not been established. SNP slave on MM module requires PL PU privilege level to operate. The SNP slave has rejected a request to change to a higher or lower privilege level. n SNP-X request was aborted prior to completion due to reception of a reak. (lock heck ode) error has occurred on an X-ttach Response message when establishing a new SNP-X communication session. ommunications have not been established. SNP Request or Response message exceeds maximum data length of the MM module. (Total data length for Mailbox and all following uffer messages is 0 bytes.) The master must use a smaller data length. Use multiple requests if total data length exceeds the maximum value. n X-uffer message was received containing greater than 000 bytes of data. The data is ignored. n invalid message type was received when an X-ttach Response was required when establishing a new SNP-X communication session. ommunications have not been established. Improper Write atagram message format. Series 0-0 slave devices use a different format for this message than Series 0-0 or Series 0-0 slave devices. The master must use the proper message format for this SNP slave device. (The SNP master in the MMmodule sends this message as part of the Establish atagram OMMREQ command. The datagram has been partially established, but is not usable; the datagram should be cancelled by using the atagram I returned by the OMMREQ.) The SNP-X slave did not receive a response from the Service Request Processor in the PL PU. n invalid next message type value was detected in an X-ttach Response message when establishing a new SNP-X communication session. ommunications have not been established. datagram error occurred in a Series 0-0 slave device (dual-port error). PL backplane communications error. n invalid response code was detected in an X-ttach Response message when establishing a new SNP-X communication session. ommunications have not been established. n expected X-ttach Response message was not received within the response timeout interval when establishing a new SNP-X communication session. The master has retried the X-ttach message twice without receiving a response. ommunications have not been established. parity error has occurred on an X-ttach Response message when re-establishing an existing SNP-X communication session. ommunications have not been established. parity error has occurred in a received X-ttach message. framing or overrun error has occurred on an X-ttach Response message when re-establishing an existing SNP-X communication session. ommunications have not been established. framing or overrun error has occurred in a received X-ttach message. (lock heck ode) error has occurred on an X-ttach Response message when re-establishing an existing SNP-X communication session. ommunications have not been established. (lock heck ode) error has occurred in a received X-ttach message. (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

246 ppendix - Panel and PL Error ode Tables 0 GE 0-0 SNPX Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0x0 0x0F 0x0 0x0F 0x0 0x0F 0x0 0x00 0x00F 0x0 0x0F 0x0 0x0F 0x0 0x0 0x0 0x0 0x00 0x00F 0x0 0x0F 0x0 0x0F 0x0 0x0F 0x0 0x0 0x0 PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) escription n invalid message type was received when an X-ttach Response was required when re-establishing an existing SNP-X communication session. ommunications have not been established. n invalid Message Type was received when an X-ttach message was required. (For an X-ttach message, the message type must be h = T.) n invalid Next Message Type value was detected in an X-ttach Response message when re-establishing an existing SNP-X communication session. ommunications have not been established. n invalid Next Message Type value was detected in a received X-ttach message. (For an X-ttach message, the Next Message Length must be zero.) n invalid response code was detected in an X-ttach Response message when re-establishing an existing SNP-X communication session. ommunications have not been established. n invalid request code was detected in a received X-ttach message. n expected X-ttach Response message was not received within the response timeout interval when re-establishing an existing SNP-X communication session. The master has retried the X-ttach message twice without receiving a response. ommunications have not been established. parity error has occurred on an X-Response message. parity error has occurred in a received X-Request message. framing or overrun error has occurred on an X-Response message. framing or overrun error has occurred in a received X-Request message. (lock heck ode) error has occurred on an X-Response message. (lock heck ode) error has occurred in a received X-Request message. n invalid message type was received when an X-Response message was required. n invalid next message type value was detected in an X-Response message. n invalid response code was detected in an X-Response message. n expected X-Response message was not received within the response time. parity error has occurred on an Intermediate Response message. parity error has occurred in a received X-uffer message. framing or overrun error has occurred on an Intermediate Response message. framing or overrun error has occurred in a received X-uffer message. (lock heck ode) error has occurred on an Intermediate Response message. (lock heck ode) error has occurred in a received X-uffer message. n invalid message type was received when an Intermediate Response message was required. n expected X-uffer message was not received. n invalid next message type value was detected in an Intermediate Response message. n invalid response code was detected in an Intermediate Response message. n expected Intermediate Response message was not received within the response timeout interval. (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) -0 E-USER-M Hardware User Manual, st Ed. Rev. G

247 ppendix - Panel and PL Error ode Tables GE 0-0 SNPX Protocol PL Error ode Tables (cont d) PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) Panel Error ode PL- Hex Value escription 0x0 ad OS Version. Must have OS.0, or later, to support the SNP OS river. 0xE0 P Serial port configured for SNP Master driver is not open; no communication can take place. 0xF0 Out of Sequence SNP message. SNP message type received was not the type expected. 0x00 ad SNP encountered. Transmission was aborted after maximum retries due to a bad lock heck ode. 0x0 ad SNP communication. Transmission was aborted after maximum retries due to serial errors (that is, parity, overrun, or framing errors). 0x0 No SNP communication. Either communication has been lost or a communication session has not been established. 0x0 Invalid block state transition. 0x0 The OEM key is NULL (inactive). 0x0 Text length does not match traffic type. 0x0 Verify with F ard or EEPROM failed. 0x0 No task level Rack/Slot configuration to read or delete. 0x0 ontrol Program (P) tasks exist but requestor not logged into main P. 0x0 Passwords are set to inactive and cannot be enabled or disabled. 0x0 Password(s) already enabled and can not be forced inactive. 0x0 Login using non zero buffer size required for block commands. 0x0 evice is write protected. 0x0 comm or write verify error occurred during save or restore. 0x0 ata stored on device has been corrupted and is no longer reliable. 0x0 ttempt was made to read a device but no data has been stored on it. 0xE0 Specified device has insufficient memory to handle request. 0xF0 Specified device is not available in the system (not present). 0x00 One or more PL modules configured have unsupported revision. 0x0 Packet size or total program size does not match input. 0x0 Invalid write mode parameter. 0x0 User Program Module (UPM) read or write exceeded block end. 0x0 Mismatch of configuration checksum. 0x0 Invalid block name specified in datagram. 0x0 Total datagram connection memory exceeded. 0x0 Invalid datagram type specified. 0x0 Point length not allowed. 0x0 Transfer type invalid for this Memory Type selector. 0x0 Null pointer to data in Memory Type selector. 0x0 Invalid Memory Type selector in datagram. 0x0 Unable to find connection address. 0x0 Unable to locate given datagram connection I. 0xE0 Size of datagram connection invalid. 0xF0 Invalid datagram connection address. (PL generated error codes for the GE 0-0 SNPX protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

248 ppendix - Panel and PL Error ode Tables 0 GE 0-0 SNPX Protocol PL Error ode Tables (cont d) Panel Error ode PL- Hex Value 0xE00 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xE0 0xEE0 0xEF0 0xF00 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xF0 0xFE0 0xFF0 PL Errors for GE 0-0 SNPX Protocol (Minor-Major) (cont d) escription Service in process cannot login. No I/O configuration to read or delete. IOS could not delete configuration, or bad type. PU revision number does not match. Memory Type for this selector does not exist. OS file area not formatted. PU model number does not match. onfiguration is not valid. No user memory is available to allocate. Memory Type selector not valid in context. Not logged in to process service request. Task unable to be deleted. Task unable to be created. VME bus error encountered. ould not return block sizes. Programmer is already attached. Request only valid in stop mode. Request only valid from programmer. Invalid program cannot log in. I/O configuration mismatch. Invalid input parameter in request. Invalid password. Invalid sweep state to set. Required to log in to a task for service. Invalid Task Name referenced. Task address out of range. annot replace I/O module. annot clear I/O configuration. I/O configuration is invalid. Unable to perform auto configuration. No privilege for attempted operation. Service Request Error has been aborted. - E-USER-M Hardware User Manual, st Ed. Rev. G

249 ppendix - Panel and PL Error ode Tables Mitsubishi FX Protocol PL Error odes Only errors as listed in the Touch Panel Error ode Table shown previously in this ppendix can occur when using the Mitsubishi FX protocol, there are no PL generated errors. Omron Panel Error ode PL- Explanation The PL- error code is used to show any errors that are generated by the connected PL. The PL- error message includes a four digit hexadecimal value embedded in the message. This value can be looked up in the specific PL s error tables to determine the cause of the error. The possible PL generated error codes for the Omron Host Link and FINS communication protocol are represented by a hexadecimal value as shown in the following message example. Omron Error ode PL- Message Example: Error code 00 returned from PL Panel error code PL- showing a hexadecimal value of 00 indicates an Framing error. PL error when using the Omron Host Link protocol. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

250 ppendix - Panel and PL Error ode Tables 0 Omron Host Link Protocol PL Error ode Table The following table lists the errors that can be generated by the Omron PL when using the Host Link protocol. Panel Error ode PL- Hex Value 0x0000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x000 0x000 0x00 0x00 0x00 0x00 0x00 0x00 0x000 NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Error odes for Omron Host Link escription Normal ompletion. Not executable in RUN mode. Not executable in MONITOR mode. Not executable with PROM mounted. ddress over (data overflow). Not executable in PROGRM mode. Not executable in EUG mode. Not executable in LOL mode. Parity error. Framing error. Overrun. FS error. Format error (parameter length error). Entry number data error (parameter error, data code error, data length error). Instruction not found. Frame length error. Not executable (due to Un-executable error clear, non-registration of I/O table, etc.). I/O table generation impossible (unrecognized remote I/O unit, channel over, duplication of optical transmitting I/O unit). bort due to parity error in transmit data under process. bort due to framing error in transmit data under process. bort due to overrun in transmit data under process. bort due to FS error in transmit data under process. bort due to format error in transmit data under process. bort due to frame length error in transmit data under process. bort due to entry number data error in transmit data under process. Un-executable due to program area capacity other than k bytes. - E-USER-M Hardware User Manual, st Ed. Rev. G

251 ppendix - Panel and PL Error ode Tables Omron FINS Protocol PL Error ode Table The following table lists the errors that can be generated by the Omron PL when using the FINS protocol. Panel Error ode PL- Hex Value 0x0000 0x000 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x0 0x0 0x0 NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Error odes for Omron FINS escription Normal ompletion. Service anceled. Local Error: Local node not in network. Local Error: Token Timeout. Local Error: Retries Failed. Local Error: Too many send frames. Local Error: Node address range error. Local Error: Node ddress uplication. estination Node Error: estination Node not in network. estination Node Error: Unit Missing. estination Node Error: Third Node missing. estination Node Error: estination Node busy. estination Node Error: Response Timeout. ontroller Error: ommunications ontroller Error. ontroller Error: PU Unit Error. ontroller Error: ontroller Error. ontroller Error: Unit number Error. Service Unsupported: Undefined ommand. Service Unsupported: Not supported by Model/Version. Routing Table Error: estination address setting error. Routing Table Error: No routing tables. Routing Table Error: Routing table error. Routing Table Error: Too many delays. ommand Format Error: ommand too long. ommand Format Error: ommand too short. ommand Format Error: Elements/ata don t match. ommand Format Error: ommand format error. ommand Format Error: Header Error. Parameter Error: rea classification missing. Parameter Error: ccess Size Error. Parameter Error: ddress range error. (PL generated error codes for the Omron FINS protocol continued on the next page.) 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

252 ppendix - Panel and PL Error ode Tables 0 Omron FINS Protocol PL Error ode Table (cont d) PL Error odes for Omron FINS Panel Error ode PL- Hex Value escription 0x0 Parameter Error: ddress range exceeded. 0x0 Parameter Error: Program Missing. 0x0 Parameter Error: Relational Error. 0x0 Parameter Error: uplicate ata ccess. 0x0 Parameter Error: Response too long. 0x0 Parameter Error: Parameter Error. 0x00 Read Not Possible: Protected. 0x00 Read Not Possible: Table missing. 0x00 Read Not Possible: ata missing. 0x00 Read Not Possible: Program missing. 0x00 Read Not Possible: File missing. 0x00 Read Not Possible: ata mismatch. 0x0 Write Not Possible: Read Only. 0x0 Write Not Possible: Protected - cannot write data link table. 0x0 Write Not Possible: annot register. 0x0 Write Not Possible: Program missing. 0x0 Write Not Possible: File missing. 0x0 Write Not Possible: File name already exists. 0x0 Write Not Possible: annot change. 0x0 Not executable in current mode: Not possible during execution. 0x0 Not executable in current mode: Not possible while running. 0x0 Not executable in current mode: Wrong PL mode (Program). 0x0 Not executable in current mode: Wrong PL mode (ebug). 0x0 Not executable in current mode: Wrong PL mode (Monitor). 0x0 Not executable in current mode: Wrong PL mode (Run). 0x0 Not executable in current mode: Specified node not polling node. 0x0 Not executable in current mode: Step cannot be executed. 0x0 No such device: File device missing. 0x0 No such device: Missing memory. 0x0 No such device: lock missing. 0x0 annot Start/Stop: Table missing. 0x0 Unit Error: Memory Error. 0x0 Unit Error: I/O setting Error. 0x0 Unit Error: Too many I/O points. 0x0 Unit Error: PU bus error. 0x0 Unit Error: I/O uplication. (PL generated error codes for the Omron FINS protocol continued on the next page.) - E-USER-M Hardware User Manual, st Ed. Rev. G

253 ppendix - Panel and PL Error ode Tables Omron FINS Protocol PL Error ode Table (cont d) PL Error odes for Omron FINS Panel Error ode PL- Hex Value escription 0x0 Unit Error: I/O bus error. 0x0 Unit Error: SYSM US/ error. 0x0 Unit Error: PU us Unit Error. 0x0 Unit Error: SYSM US No. duplication. 0x0F Unit Error: Memory Error. 0x0 Unit Error: SYSM US terminator missing. 0x0 ommand Error: No protection. 0x0 ommand Error: Incorrect password. 0x0 ommand Error: Protected. 0x0 ommand Error: Service already executing. 0x0 ommand Error: Service stopped. 0x0 ommand Error: No execution right. 0x0 ommand Error: Settings not complete. 0x0 ommand Error: Necessary items not set. 0x0 ommand Error: Number already defined. 0x0 ommand Error: Error will not clear. 0x00 ccess Right Error: No access right. 0x00 bort: Service aborted. E-USER-M Hardware User Manual, st Ed. Rev. G 0 -

254 ppendix - Panel and PL Error ode Tables 0 Omron Panel Error ode P Explanation The PL- error code is used to show any errors that are generated by the connected PL. The PL- error message includes a four digit hexadecimal value embedded in the message. This value can be looked up in the specific PL s error tables to determine the cause of the error. The possible PL generated error codes for the Omron S/J FINS Ethernet communication protocol are represented by a hexadecimal value as shown in the following message example. Omron Error ode PL- Message Example: Error code 00 returned from PL Panel error code PL- showing a hexadecimal value of 00 indicates a Routing table error: Too many relays PL error. - E-USER-M Hardware User Manual, st Ed. Rev. G

255 ppendix - Panel and PL Error ode Tables Omron S/J FINS Ethernet Protocol PL Error ode Table The following table lists the errors that can be generated by the Omron PL when using the S/J FINS Ethernet protocol. NOTE: The following errors can be generated from the designated PL, are monitored by the -more touch panel, and displayed on the touch panel s screen as a hexadecimal value in panel error code PL- message, if active. Please refer to the PL manufacturer s documentation for additional information. PL Error odes for Omron S/J FINS Ethernet Panel Error ode PL- Hex Value escription 00 Local Error: Send Error from lack of buffer space. Try reducing Ethernet load to the module. 00 estination Node Error: IP address of remote node not set correctly. 00 estination Node Error: No node with the specified unit address found. 00 estination Node Error: Packet corrupted or Response timeout. Try increasing timeout. 00 ontroller Error: ommunications controller error. 00 ontroller Error: PU Unit error. heck error LEs on PL. Refer to documentation for that PU. 00 ontroller Error: Unit number error. Make sure Unit number is not used twice. 00 Service unsupported: Undefined command. 00 Routing table error: estination address setting error. Routing table incorrect. 00 Routing table error: No routing tables. 00 Routing table error: Routing table error. 00 Routing table error: Too many relays. 00 ommand format error: ommand too long. ad packet: check for electrical noise and grounding. 00 ommand format error: ommand too short. ad packet: check for electrical noise and grounding. 00 ommand format error: Elements/data don t match. ad packet: check for electrical noise and grounding. 00 ommand format error: Header error. This is the error received when station # set in the command does not match the station # of the Ethernet module. 00 Parameter error: UP socket number bad. 0 Parameter error: ddress requested does not exist in PL. 0 Parameter error: ddress area requested in not accessible. 0F Status error: uplicate Socket error. 0 Status error: Specified socket not open. 0 Environment Error: IP address conversion failed. Only encountered when using routing tables. 0 Environment Error: IP address conversion set for automatic. 0 Unit error: I/O setting error. 0 Unit error: PU bus error. 0 Unit error: PU us Unit error. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

256 ppendix - Panel and PL Error ode Tables 0 Siemens Panel Error ode P Explanation The PL- error code is used to show any errors that are generated by the connected PL. The PL- error message includes a four digit hexadecimal value displayed at the end of the message. This value can be looked up in the specific PL s error tables to determine the cause of the error. The possible PL generated error codes for the Siemens PPI communication protocols breakdown into a four digit hexadecimal value as shown in the following message example. Siemens Error ode PL- Message Example: Error code 0x0 returned from PL Panel error code PL- showing a hexadecimal value of 0x0 indicates an ddress is invalid. PL error. -0 E-USER-M Hardware User Manual, st Ed. Rev. G

257 ppendix - Panel and PL Error ode Tables Siemens PPI Protocol PL Error ode Table Panel Error ode PL- Hex Value 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x00 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0E 0x0 PL PU Header Errors for S-00 PPI escription Hardware Fault. Object access not allowed: Occurs when access to Timer and ounter data type is set to Signed Integer and not. ontext not supported. ddress out of range: Occurs when requesting an address within a ata lock that does not exist or is out of range. ddress out of range. Write ata size mismatch. Object does not exist: Occurs when trying to request a ata lock that does not exist. Function being used. ction is not allowed in current mode. Hardware fault. ccess not allowed. Function not supported. ddress invalid. ata Type not supported. ata Type is not consistent with size. Object does not exist. PU Size is incorrect. ddress is invalid. lock name syntax error. Error with function parameter. Error with block type. No linked block. Object already exists. Object already exists. lock already used in EPROM. lock does not exist. No lock does not exist. lock number incorrect. 0 E-USER-M Hardware User Manual, st Ed. Rev. G -

258 ppendix - Panel and PL Error ode Tables 0 Siemens ISO over TP Protocol PL Error ode Table Panel Error ode PL- Hex Value 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x000 0x00 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x00 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0E 0x0 PL PU Header Errors for S-00 PU, S-00 Ethernet escription Hardware Fault. Object access not allowed: Occurs when access to Timer and ounter data type is set to Signed Integer and not. ontext not supported. ddress out of range: Occurs when requesting an address within a ata lock that does not exist or is out of range. ddress out of range. Write ata size mismatch. Object does not exist: Occurs when trying to request a ata lock that does not exist. Function being used. ction is not allowed in current mode. Hardware fault. ccess not allowed. Function not supported. ddress invalid. ata Type not supported. ata Type is not consistent with size. Object does not exist. PU Size is incorrect. ddress is invalid. lock name syntax error. Error with function parameter. Error with block type. No linked block. Object already exists. Object already exists. lock already used in EPROM. lock does not exist. No lock does not exist. lock number incorrect. - E-USER-M Hardware User Manual, st Ed. Rev. G

259 Touch Panel Runtime Errors ppendix In This ppendix... Introduction... - Runtime Errors... - Log File Naming...-

260 ppendix - Touch Panel Runtime Errors 0 Introduction The -more touch panels have diagnostics built-in to the operating system that monitor various runtime functions that will display an error message on the panel s display indicating that a particular error has occurred and what the error represents. The Error Message(s) is displayed in the upper left area of the display screen. The Runtime Errors are also logged into the panel s Error log under the Information tab in the panel s System Setup Screens. The Error Log ode, for example RTE-00, identifies the error on the System Screen - Error tab and in the error log. See hapter : System Setup Screens for additional details. The tables that follow show the possible Runtime Errors. The user can include in their touch panel project the use of this diagnostic information by using the system tag name SYS ERR ERROROE to control displayed screens, operator messages, etc., and also communicate error information to the PL or controlling device. If a runtime error occurs, the SYS ERR ERROROE system tag will contain the numeric value shown under the Tag ode Error Value. For example, For example, if the panel project is configured to log to US and no US flash drive is installed in the panel, the panel will display RTE-00 Log buffer memory is full and the SYS ERR ERROROE system tag will contain the value 00. The value of the last runtime error detected will remain in the SYS ERR ERROROE. If you have difficulty determining the cause of the error, refer to hapter : Troubleshooting for additional help or contact our technical support group at Error Message H0-EOM/H0-EOM00 Ethernet Module L0 PL Stride Ethernet Switch 0/00 ase-t (such as SE-SWU) Ethernet T able RTE-00 Log buffer memory is full -more Touch Panel uto MI / MI-X Ethernet Port - E-USER-M Hardware User Manual, st Ed. Rev. G