M3093GX\DG\M3096G\GX\M3097G+\DG Fi-4340C\Fi-4530C\Fi-4640S\M4097D\Fi-4750C\L\Fi-5750 SCSI Win2000\XP Installation Procedure

Transcription

1 Step A: Required hardware. To install these models you will need a Narrow SCSI 50-pin controller and six foot (maximum) Narrow SCSI cable. Step B: Removing the shipping bracket. It is recommended that before you connect the scanner to your computer that you inspect the scanner and remove the shipping bracket first. Removing the shipping bracket: The flatbed scanner models typically come with a factory installed shipping lock designed to protect the scanner during shipment. Before the scanner can be used the shipping lock must be unlocked. Follow these instructions to unlock the shipping bracket: 1. Slide the scanner to its side as shown in figure below. 2. Unscrew the retainer screw and remove the shipping bracket. 3. Place the shipping bracket in the use position slot and secure it with the retainer screw (see figure below) 4. Place scanner back in its normal position

2 Special note: The Fi-4340C shipping lock is a knob located underneath the exit tray. To unlock it twist a quarter turn counter-clockwise so that it is vertical. The Fi-4530C does not have a shipping lock. Step C: Installing the SCSI Host Adapter. 1. Shut down your PC and remove the case cover. 2. Locate a free PCI slot and remove the back plate if necessary. 3. Install the SCSI controller in an open PCI slot. Make sure that the card is seated completely in the slot and secured in the frame Warning! Failure to secure the SCSI controller in the PC can result in damage to the SCSI card, scanner, and/or your system. 4. Boot your PC without the scanner attached. Step D: Installing the SCSI drivers (Adaptec). 1. When the New Hardware wizard comes up, allow Windows to finish installing the files for the SCSI controller. 2. Then go to and click on the search tab. Scroll down to the Enter key word or quoted phrase box and type in aspi. 3. Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the prompts to download it. 4. Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder. For Win2000 go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE and run it. For WinXP go to start, run, browse to the Adaptec\ASPI folder, select INSTALL.BAT file in the directory the files extracted to and select the OPEN button. In the command box, add a space and either XP32 for Pentium I/II/III/IV processors or XP64 for Itanium processors. The command should look like: c:\adaptec\aspi\install.bat XP32 or c:\adaptec\aspi\install.bat XP64. Then select the OK button to run it. 5. Reboot and check for errors. If no errors shut down your system and go to the next step. Step E: Connecting the Scanner. Warning! Ensure power is off when connecting or disconnecting any cables to the scanner or workstation. Setting the SCSI ID: The factory setting for the Scanner is 6, however, selecting a different SCSI ID may be required when there are several devices on a SCSI chain. Using a suitable tool, turn the selector switch until the arrow points to the desired ID number (see figure 2-3). Setting the SCSI ID to 0, 1, or 7 is NOT recommended as these settings are typically reserved for hard drives and the SCSI host adapter. Setting Termination: The Fujitsu M3093GX\M3096G\GX\M3097G+\DG scanners come with a plug in SCSI terminator (see figure below). The Fi-4340C\Fi-4640S\M4097D\Fi- 4750C\L scanners come with built in termination that is turned on or off through the scanner panel. Termination for the Fi-4530C is handled automatically by the scanner. If the scanner is the last device on the SCSI chain then the terminator should be placed on

3 one of the SCSI ports or turned on. If the scanner is not the last device on the SCSI chain, then the terminator should be removed or turned off before connecting to the next SCSI device. Connecting SCSI cable: Located on the back of the scanner are the SCSI ports. Depending on the model the ports may be either a High Density 50-pin (HD-50) or a 50- pin Centronics. Use the appropriate cable to connect the scanner to the SCSI controller in your PC. Ensure all connections are securely fastened. Powering On: Connect the power cord to the scanner and a wall outlet then turn on the scanner. For those models without a power switch plug in the power supply to the back of the scanner. For proper communication between the Scanner and the Workstation, switch on the scanner prior to switching on the workstation. The scanner power and LCD display will light up. Next after the scanner completes its startup initialization the LCD will display either ready or the number one. This indicates that the scanner is ready. Step F: Installing the ISIS driver. 1. Create a new folder and name it ISIS Download. 5. Afterwards click on ISIS Software Drivers. 6. Locate the appropriate ISIS driver for your scanner by cross-referencing the scanner model column on the left to the software column. have the ISIS Download folder you created in the Save In Box. 10. When completed close the Download Complete window and go to the ISIS 11. Open the folder and you will see the saved ISIS driver file. Double click on the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and select the

4 ISIS Download folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip. 12. In the ISIS Download folder locate the setup.exe file and double click. Afterwards follow the prompts and reboot when finished. Step G: Installing the STI-Twain driver for the Fi-4340C\Fi-4530C\Fi-4640S\M4097D\ Fi-4750C\L\Fi Special note: Use the ASPI-Twain driver for the. 1. Create a new folder and name it Twain Download. 5. Afterwards click on STI Twain Software Drivers. 6. Locate the appropriate STI Twain driver for your scanner by cross-referencing the scanner model column on the left to the software column. have the Twain Download folder you created in the Save In Box. 10. When completed close the Download Complete window and go to the Twain 11. Open the folder and you will see the saved STI Twain driver file. Double click on the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and select the STI Twain Download folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip. 12. In the STI Twain Download folder locate the setup.exe file and double click. Afterwards follow the prompts and reboot when finished. Step H: Installing the Twain driver for the. 1. Create a new folder and name it Twain Download. 5. Afterwards click on ASPI Twain Software Drivers. 6. Locate the appropriate ASPI Twain driver for your scanner by cross-referencing the scanner model column on the left to the software column. have the Twain Download folder you created in the Save In Box. 10. When completed close the Download Complete window and go to the Twain 11. Open the folder and you will see the saved ASPI Twain driver file. Double click on the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and select the ASPI Twain Download folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip.

5 12. In the ASPI Twain Download folder locate the setup.exe file and double click. Afterwards follow the prompts and reboot when finished. Step H: Installing Scandall Create a new folder and name it Scandall Download. 4. On the next page select your Drivers and Downloads. 5. Afterwards click on Software Utilities. 6. Double click on the file name and the File Download box will popup. 7. Click on Save and then use the browse (or other folder navigation) button until you have the Scandall Download folder you created in the Save In Box. 8. Click Save. 9. When completed close the Download Complete window and go to the Scandall 10. Open the folder and you will see the saved Scandall file. Double click on the file to unzip it and the WinZip* self-extractor box will popup. Click on browse and select the Scandall Download folder, then click on Extract. The file will begin to unzip and when finished a message box will report the number of files unzipped. Click on OK and close WinZip. 11. In the Scandall Download folder locate the Scandall.exe file and double click. Afterwards follow the prompts and when finish launch Scandall. Step I: Scanning with Scandall21. Once Scandall21 is installed it is time to start scanning. 1. Launch Scandall21 by clicking on the shortcut link on your desktop or manually by clicking on Start, Programs, Scanner Utility for Microsoft Windows, then Scandall After the Untitled Screen has open, click on Scan and choose Select Source. 3. Select the Fujitsu Twain source for your scanner by highlighting it and clicking OK. You will only need to do this once unless you are scanning with multiple sources. 4. Once you are back at the Untitled Screen click on Scan and select To View this time. The Twain User Interface will popup. 5. Select the scanning parameters that you wish to use Color mode, resolution, paper size, etc 6. Next under Scan Type choose either ADF or Flatbed in the dropdown box. 7. Place your document in the ADF or on the Flatbed face down and click on the Scan button. 8. After the document is scanned close the Twain User Interface and the image will appear on the Untitled Screen. Congratulations! You have successfully completed your scanner installation. *If you do not have any unzipping software installed on your system, you can download a free evaluation copy at