Laboratory 4 Design a Muti-bit Counter and Programming a FPGA
|
|
- Virgil Carter
- 6 years ago
- Views:
Transcription
1 Laboratory 4 Design a Muti-bit Counter and Programming a FPGA For your report: The problem written in English The flowchart or function table to solve the problem if it is necessary The design entry included (VHDL and Schematic) The RTL Viewer has to be included The simulation result for designed digital component The analysis for the simulation The pin assignment- the table for assigning the circuit inputs and outputs to specific pins on the FPGA The configuration for the FPGA Device (JTAG) The test table you designed to record and verify the designed circuit on hardware Picture taken for your test if it is necessary The conclusion Background A. Approach I: Design 3-bit counter T-type flip-flop is shown in Figure 1. A T flip-flop is obtained from a JK flip-flop by tying the J and K inputs together to form the T input. Figure 1 Figure 2 shows BDF design for three-bit counter by using three T-type flip-flops Figure 2 Figure 3 is the simulation result. Check the relation among clock, Q0, Q1, and Q2 (set clr as high, en is high). For your simulation, you should consider clr as high and low, en as high and low, and observe the outputs of Q0, Q1, and Q2.
2 Figure 3 Suppose a clock frequency is clock = 24kHz The frequency of the 2 0 output line (Q0) is 1/2 of the input clock line (12kHz) The frequency of the 2 1 output line (Q1) is 1/4 of the input clock line (6kHz) The frequency of the 2 2 output line (Q2) is 1/8 of the input clock line (3kHz) B. Approach II: Design 3-bit counter VHDL design for three-bit counter (Figure 4) with and. Figure 4 Step 1. Start the Quartus II software. Select File New Project Wizard. And create a new project name under the directory C:\temp\your initial \Lab. Assign the project name counter3, assign Cyclone II for the device family, and select the EP2C35F672C6 chip in the Family & device settings, which is the FPGA used on Altera s DE2 board. Figure 5
3 Step 2. Open a new VHDL Device Design file (File > New) by highlighting VHDL File. And click OK. Type the VHDL code Step 3. Save the VHDL file (Figure 5) as.vhd as part of our project under your subfolder. Place a check mark in the space labeled Add file to current project and press Save Step 4. Select File Create/Update Create Symbol Files for Current File (.bsf symbol) to create a symbol file for the VHDL code entered. A Compilation Report window initially displays Report not available ; however, be patient. A display window should soon appear stating that the Create Symbol File was (or not) successful. Click OK and close the Compilation Report window. Step 5. Open a new Schematic file (File > New) by highlighting Block Diagram/Schematic File. And click OK. Find the symbol file (bsf file you just created for VHDL in Step 4) from Project folder to support your design in BDF view. Insert the symbol and input/output pins OUTPUT Figure 6 Step 6. Before compiling this bdf file, we need to name this bdf file and save it as part of our project under your subfolder. Choose File > Save As and enter File name as counter3. Place a check mark in the space labeled Add file to current project and press Save. Step 7. create a Vector Waveform File (vwf) to simulate a design(bdf) file. Set an end time 30 µs for simulation from Edit and then run simulation based on Figure 3. You may have to expand the size of the Simulation Waveforms to suit your need and choose View > Fit in Window to see the entire 30µs waveform. Figure 7 is the simulation result. Check the relation among clock,,, count_out[0], count_out[1], count_out[2]. Integrated the decoder with 3-bit counter Step 1. design a decode in vhdl (Figure 8) Figure 7
4 Figure 8 Step 2. Save the VHDL file as dec7seg.vhd as part of our project under your subfolder. Place a check mark in the space labeled Add file to current project and press Save Step 3. Select File Create/Update Create Symbol Files for Current File (dec7seg.bsf symbol) to create a symbol file for the VHDL code entered. Step 4. Open a new Schematic file (File > New) by highlighting Block Diagram/Schematic File. And click OK. Find the symbol file (bsf file you created for VHDL) from Project folder to support your design in BDF view. Insert the symbol and input/output pins dec7seg dec[2..0] 1 display[0..6] OUTPUT display[0..6] Figure 9 Step 5. Before compiling this bdf file, we need to name this bdf file and save it as part of our project under your subfolder. Choose File > Save As and enter File name as counter3. Place a check mark in the space labeled Add file to current project and press Save. Step 6. Compile this integrated design (Figure 9) Step 7. You can make a pin configuration, compile your design, and download your design to FPGA board to test your digital system. Step 8. Use the pushbutton KEY0 as the Clock input, switches SW1 and SW0 as Enable and Reset inputs, and 7-segment displays HEX0 to display the hexadecimal count as your circuit operates.
5 Your Turn to Design Project: Consider the circuit in Figure 10. It is a 4-bit synchronous counter which uses four T-type flip-flops. The counter increments its count on each positive edge of the clock if the Enable signal is asserted. The counter is to 0 by using the Reset signal. Figure 10. A 4-bit counter 4-bit counter 1. Write a VHDL file or create a BDF file that defines a 4-bit counter by using the structure depicted in bdf (Figure 2) or vhdl(figure 5), and compile the circuit. What is the frequency relation between the clock and four outputs from four T-type flip-flops, respectively? 2. Create a waveform vector and simulate your circuit to verify its correctness of the design of 4-bit counter. 3. Is this counter counting up or counting down? 4. Augment your VHDL file or BDF file to use the pushbutton KEY0 as the Clock input, switches SW1 and SW0 as Enable and Reset inputs, and 7-segment displays HEX0 to display the hexadecimal count as your circuit operates. 5. Make the necessary pin assignments and compile the circuit. 6. Programming FPGA and test your implementation. You may use the following library in your VHDL design entry: LIBRARY ieee; USE ieee.std_logic_1164.all; USE ieee.std_logic_unsigned.all; your code 12-bit counter design 7. Write a VHDL file or create a BDF file that defines a 12-bit counter by reusing the component of 4-bit counter, and compile the circuit. What is the frequency relation between the clock and all 12 outputs of Q namely Q 0, Q 1, Q 2, Q 3, Q 4, Q 5, Q 6, Q 7, Q 8, Q \9, Q 10, Q 11? 8. Create a waveform vector and simulate your circuit to verify its correctness of the design of 12-bit counter. 9. Augment your VHDL file to use the pushbutton KEY0 as the Clock input, switches SW1 and SW0 as Enable and Reset inputs, and 7-segment displays HEX2, HEX1, HEX0 (or LCD) to display the hexadecimal count as your circuit operates. 10. Make the necessary pin assignments and compile the circuit. 11. Programming FPGA and test your implementation.
Laboratory 4 Design a Muti-bit Counter
Laboratory 4 Design a Muti-bit Counter Background A. Approach I: Design 3-bit counter with and clear T-type flip-flop is shown in Figure 1. A T flip-flop is obtained from a JK flip-flop by tying the J
Lab 6: Integrated the Decoder with Muti-bit Counter and Programming a FPGA
Lab 6: Integrated the Decoder with Muti-bit Counter and Programming a FPGA For your report: The problem written in English The flowchart or function table to solve the problem if it is necessary The design
CET4805 Component and Subsystem Design II. EXPERIMENT # 5: Adders. Name: Date:
EXPERIMENT # 5: Adders Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Design a half adder by extracting the
CET4805 Component and Subsystem Design II. EXPERIMENT # 2: VHDL(VHSIC Hardware Descriptive Language) Name: Date:
EXPERIMENT # 2: VHDL(VHSIC Hardware Descriptive Language) Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Learn
EMT1250 LABORATORY EXPERIMENT. EXPERIMENT # 7: VHDL and DE2 Board. Name: Date:
EXPERIMENT # 7: VHDL and DE2 Board Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Learn how to create and modify
EMT1250 LABORATORY EXPERIMENT. EXPERIMENT # 10: Implementing Binary Adders. Name: Date:
EXPERIMENT # 10: Implementing Binary Adders Name: Date: Equipment/Parts Needed: PC (Altera Quartus II V9.1 installed) DE-2 board Objective: Design a half adder by extracting the Boolean equation from a
Laboratory Exercise 3
Laboratory Exercise 3 Latches, Flip-flops, and egisters The purpose of this exercise is to investigate latches, flip-flops, and registers. Part I Altera FPGAs include flip-flops that are available for
Terasic DE0 Field Programmable Gate Array (FPGA) Development Board
Lecture FPGA-01 DE0 FPGA Development Board and Quartus II 9.1 FPGA Design Software Terasic DE0 Field Programmable Gate Array (FPGA) Development Board 1 May 16, 2013 3 Layout and Components of DE0 May 16,
EMT1250 LABORATORY EXPERIMENT. EXPERIMENT # 6: Quartus II Tutorial and Practice. Name: Date:
EXPERIMENT # 6: Quartus II Tutorial and Practice Name: Date: Equipment/Parts Needed: Quartus II R Web Edition V9.1 SP2 software by Altera Corporation USB drive to save your files Objective: Learn how to
CPE 200L LABORATORY 4: INTRODUCTION TO DE2 BOARD UNIVERSITY OF NEVADA, LAS VEGAS GOALS: BACKGROUND:
CPE 200L LABORATORY 4: INTRODUCTION TO DE2 BOARD DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS GOALS: Getting familiar with DE2 board installation, properties, usage.
UNIVERSITY OF CALIFORNIA, DAVIS Department of Electrical and Computer Engineering. EEC180A DIGITAL SYSTEMS I Winter 2015
UNIVERSITY OF CALIFORNIA, DAVIS Department of Electrical and Computer Engineering EEC180A DIGITAL SYSTEMS I Winter 2015 LAB 1: Introduction to Quartus II Schematic Capture and ModelSim Simulation This
Introduction to VHDL Design on Quartus II and DE2 Board
ECP3116 Digital Computer Design Lab Experiment Duration: 3 hours Introduction to VHDL Design on Quartus II and DE2 Board Objective To learn how to create projects using Quartus II, design circuits and
Tutorial for Altera DE1 and Quartus II
Tutorial for Altera DE1 and Quartus II Qin-Zhong Ye December, 2013 This tutorial teaches you the basic steps to use Quartus II version 13.0 to program Altera s FPGA, Cyclone II EP2C20 on the Development
Laboratory Exercise 7
Laboratory Exercise 7 Finite State Machines This is an exercise in using finite state machines. Part I We wish to implement a finite state machine (FSM) that recognizes two specific sequences of applied
Laboratory Exercise 8
Laboratory Exercise 8 Memory Blocks In computer systems it is necessary to provide a substantial amount of memory. If a system is implemented using FPGA technology it is possible to provide some amount
ENEE 245 Lab 1 Report Rubrics
ENEE 4 Lab 1 Report Rubrics Design Clearly state the design requirements Derive the minimum SOP Show the circuit implementation. Draw logic diagram and wiring diagram neatly Label all the diagrams/tables
Quick Tutorial for Quartus II & ModelSim Altera
Quick Tutorial for Quartus II & ModelSim Altera By Ziqiang Patrick Huang Hudson 213c Ziqiang.huang@duke.edu Download & Installation For Windows or Linux users : Download Quartus II Web Edition v13.0 (ModelSim
FPGA Introductory Tutorial: Part 1
FPGA Introductory Tutorial: Part 1 This tutorial is designed to assist in learning the basics of the Altera Quartus II v9.0 software. Part 1 of the tutorial will cover the basics of creating a Project,
Chip Design with FPGA Design Tools
Chip Design with FPGA Design Tools Intern: Supervisor: Antoine Vazquez Janusz Zalewski Florida Gulf Coast University Fort Myers, FL 33928 V1.9, August 28 th. Page 1 1. Introduction FPGA is abbreviation
Chapter 2 Getting Hands on Altera Quartus II Software
Chapter 2 Getting Hands on Altera Quartus II Software Contents 2.1 Installation of Software... 20 2.2 Setting Up of License... 21 2.3 Creation of First Embedded System Project... 22 2.4 Project Building
QuartusII.doc 25/02/2005 Page 1
1 Start Icon... 2 1.1 The Quartus II Screen... 2 2 Project creation... 2 3 Schematic entry... 5 3.1 Create new drawing... 5 3.2 Symbol selection... 7 3.3 Placement of an AND gate... 8 3.4 Deleting a symbol...
TUTORIALS FOR MAX3000A CPLD DEVICES
TUTORIALS FOR MAX3000A CPLD DEVICES WEL LAB 6-BIT-UP-DOWN-COUNTER CONTENTS: INTRODUCTION.. GETTING STARTED. DESIGN ENTRY. PIN ASSIGNMENT. PROGRAMMING CPLD DEVICE. REFERENCES. WEL LAB, IIT BOMBAY Page 2
CSEE W4840 Embedded System Design Lab 1
CSEE W4840 Embedded System Design Lab 1 Stephen A. Edwards Due January 31, 2008 Abstract Learn to use the Altera Quartus development envrionment and the DE2 boards by implementing a small hardware design
QUARTUS II Altera Corporation
QUARTUS II Quartus II Design Flow Design Entry Timing Constraints Synthesis Placement and Routing Timing, Area, Power Optimization Timing and Power Analyzer Optimized Design 2 Can I still use a Processor?
Physics 536 Spring Illustrating the FPGA design process using Quartus II design software and the Cyclone II FPGA Starter Board.
Physics 536 Spring 2009 Illustrating the FPGA design process using Quartus II design software and the Cyclone II FPGA Starter Board. Digital logic: Equivalent to a large number of discrete logic elements
Lab 3: Standard Combinational Components
Lab 3: Standard Combinational Components Purpose In this lab you will implement several combinational circuits on the DE1 development board to test and verify their operations. Introduction Using a high-level
Altera Quartus II Tutorial ECE 552
Altera Quartus II Tutorial ECE 552 Quartus II by Altera is a PLD Design Software which is suitable for high-density Field-Programmable Gate Array (FPGA) designs, low-cost FPGA designs, and Complex Programmable
NIOS CPU Based Embedded Computer System on Programmable Chip
1 Objectives NIOS CPU Based Embedded Computer System on Programmable Chip EE8205: Embedded Computer Systems This lab has been constructed to introduce the development of dedicated embedded system based
SOPC LAB1. I. Introduction. II. Lab contents. 4-bit count up counter. Advanced VLSI Due Wednesday, 01/08/2003
SOPC LAB1 I. Introduction The purpose of this lab is to familiarize you with all the items in the kit. This tutorial tells you how to develop FPGA system in Quartus II. You are ready to begin using the
EE 231 Fall Lab 1: Introduction to Verilog HDL and Altera IDE
Lab 1: Introduction to Verilog HDL and Altera IDE Introduction In this lab you will design simple circuits by programming the Field-Programmable Gate Array (FPGA). At the end of the lab you should be able
University of Florida EEL 3701 Dr. Eric M. Schwartz Department of Electrical & Computer Engineering Revision 0 12-Jun-16
Page 1/14 Quartus Tutorial with Basic Graphical Gate Entry and Simulation Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate
NIOS CPU Based Embedded Computer System on Programmable Chip
NIOS CPU Based Embedded Computer System on Programmable Chip 1 Lab Objectives EE8205: Embedded Computer Systems NIOS-II SoPC: PART-I This lab has been constructed to introduce the development of dedicated
Tutorial on Quartus II Introduction Using Schematic Designs
Tutorial on Quartus II Introduction Using Schematic Designs (Version 15) 1 Introduction This tutorial presents an introduction to the Quartus II CAD system. It gives a general overview of a typical CAD
ECSE-323 Digital System Design. Lab #1 Using the Altera Quartus II Software Fall 2008
1 ECSE-323 Digital System Design Lab #1 Using the Altera Quartus II Software Fall 2008 2 Introduction. In this lab you will learn the basics of the Altera Quartus II FPGA design software through following
TUTORIALS FOR MAX3000A CPLD DEVICES
TUTORIALS FOR MAX3000A CPLD DEVICES WEL LAB BCD DECODER CONTENTS: INTRODUCTION.. GETTING STARTED. DESIGN ENTRY. PIN ASSIGNMENT. PROGRAMMING CPLD DEVICE. REFERENCES. WEL LAB, IIT BOMBAY Page 2 Introduction:
2 nd Year Laboratory. Experiment: FPGA Design with Verilog. Department of Electrical & Electronic Engineering. Imperial College London.
Department of Electrical & Electronic Engineering 2 nd Year Laboratory Experiment: FPGA Design with Verilog Objectives By the end of this experiment, you should know: How to design digital circuits using
Name EGR 2131 Lab #6 Number Representation and Arithmetic Circuits
Name EGR 2131 Lab #6 Number Representation and Arithmetic Circuits Equipment and Components Quartus software and Altera DE2-115 board PART 1: Number Representation in Microsoft Calculator. First, let s
CSEE W4840 Embedded System Design Lab 1
CSEE W4840 Embedded System Design Lab 1 Stephen A. Edwards Due February 2, 2009 Abstract Learn to use the Altera Quartus development envrionment and the DE2 boards by implementing a small hardware design
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II
ECE 3610 Microprocessing Systems Lab #1 Verilog Design of the TOC Using Quartus II This lab manual presents an introduction to the Quartus II Computer Aided Design (CAD) system. This manual gives step-by-step
UNIVERSITI MALAYSIA PERLIS
UNIVERSITI MALAYSIA PERLIS SCHOOL OF COMPUTER & COMMUNICATIONS ENGINEERING EKT 124 LABORATORY MODULE INTRODUCTION TO QUARTUS II DESIGN SOFTWARE : INTRODUCTION TO QUARTUS II DESIGN SOFTWARE OBJECTIVES To
NIOS CPU Based Embedded Computer System on Programmable Chip
NIOS CPU Based Embedded Computer System on Programmable Chip EE8205: Embedded Computer Systems NIOS-II SoPC: PART-II 1 Introduction This lab has been constructed to introduce the development of dedicated
CSEE W4840 Embedded System Design Lab 1
CSEE W4840 Embedded System Design Lab 1 Stephen A. Edwards Due February 3, 2011 Abstract Learn to use the Altera Quartus development envrionment and the DE2 boards by implementing a small hardware design
EET 1131 Lab #7 Arithmetic Circuits
Name Equipment and Components Safety glasses ETS-7000 Digital-Analog Training System Integrated Circuits: 7483, 74181 Quartus II software and Altera DE2-115 board Multisim simulation software EET 1131
University of Florida EEL 3701 Dr. Eric M. Schwartz Madison Emas, TA Department of Electrical & Computer Engineering Revision 1 5-Jun-17
Page 1/14 Example Problem Given the logic equation Y = A*/B + /C, implement this equation using a two input AND gate, a two input OR gate and two inverters under the Quartus environment. Upon completion
Engineering 303 Digital Logic Design Spring 2017
Engineering 303 Digital Logic Design Spring 2017 LAB 1 Introduction to Combo Logic and Quartus Deliverables: 0) A Simple Verilog Combinatorial Circuit 1) A Simple Block Diagram Combinatorial Circuit 2)
CS303 LOGIC DESIGN FINAL EXAM
JANUARY 2017. CS303 LOGIC DESIGN FINAL EXAM STUDENT NAME & ID: DATE: Instructions: Examination time: 100 min. Write your name and student number in the space provided above. This examination is closed
Rensselaer Polytechnic Institute Computer Hardware Design ECSE Lab Assignment 3 Altera Richards Controller and Logic Analyzer Laboratory Rev.
RPI Rensselaer Polytechnic Institute Computer Hardware Design ECSE 4770 Lab Assignment 3 Altera Richards Controller and Logic Analyzer Laboratory Rev.F Introduction This laboratory assignment is an introduction
Lab #12: ArithmeticLogic Unit
Lab #12: ArithmeticLogic Unit Zack Mattis Lab: 3/27/17 Report: 4/8/17 Partner: Brendan Schuster Purpose In this lab, a fully functioning 4-bit Arithmetic Logic Unit (ALU) was designed and fully implemented
Lab 2 EECE473 Computer Organization & Architecture University of Maine
Lab 2: Verilog Programming Instructor: Yifeng Zhu 50 Points Objectives: 1. Quatus II Programming assignment: PIN assignments, LEDs, switches; 2. Download and test the design on Altera DE2 board 3. Create
EXPERIMENT 1. INTRODUCTION TO ALTERA
EXPERIMENT 1. INTRODUCTION TO ALTERA I. Introduction I.I Objectives In this experiment, you will learn computer aided digital design and verification of it using Field Programmable Gate Arrays (FPGA).
ECE 437 Computer Architecture and Organization Lab 6: Programming RAM and ROM Due: Thursday, November 3
Objectives: ECE 437 Computer Architecture and Organization Lab 6: Programming RAM and ROM Due: Thursday, November 3 Build Instruction Memory and Data Memory What to hand in: Your implementation source
ENEE245 Digital Circuits and Systems Lab Manual
ENEE245 Digital Circuits and Systems Lab Manual Department of Engineering, Physical & Computer Sciences Montgomery College Version 1.1 Copyright Prof. Lan Xiang (Do not distribute without permission) 1
Quartus II Introduction Using Schematic Design
Quartus II Introduction Using Schematic Design This tutorial presents an introduction to the Quartus R II CAD system. It gives a general overview of a typical CAD flow for designing circuits that are implemented
Tutorial on Quartus II Introduction Using Verilog Code
Tutorial on Quartus II Introduction Using Verilog Code (Version 15) 1 Introduction This tutorial presents an introduction to the Quartus II CAD system. It gives a general overview of a typical CAD flow
CSC / EE Digital Systems Design. Summer Sample Project Proposal 01
THE CATHOLIC UNIVERSITY OF AMERICA SCHOOL OF ENGINEERING DEPARTMENT OF ELECTRICAL ENGINEERING AND COMPUTER SCIENCE CSC / EE 519-01 Digital Systems Design Summer 2013 Sample Project Proposal 01 Thursday
Advanced Electronics Lab.
College of Engineering Course Book of 2010-2011 Advanced Electronics Lab. Mr. Araz Sabir Ameen M.Sc. in Electronics & Communications ALTERA DE2 Development and Education Board DE2 Package: The DE2 package
Contents. Appendix B HDL Entry Tutorial 2 Page 1 of 14
Appendix B HDL Entry Tutorial 2 Page 1 of 14 Contents Appendix B HDL Entry Tutorial 2...2 B.1 Getting Started...2 B.1.1 Preparing a Folder for the Project...2 B.1.2 Starting Quartus II...2 B.1.3 Creating
ENEE245 Digital Circuits and Systems Lab Manual
ENEE245 Digital Circuits and Systems Lab Manual Department of Engineering, Physical & Computer Sciences Montgomery College Modified Fall 2017 Copyright Prof. Lan Xiang (Do not distribute without permission)
University of Massachusetts Amherst Computer Systems Lab 2 (ECE 354) Spring Lab 1: Using Nios 2 processor for code execution on FPGA
University of Massachusetts Amherst Computer Systems Lab 2 (ECE 354) Spring 2007 Lab 1: Using Nios 2 processor for code execution on FPGA Objectives: After the completion of this lab: 1. You will understand
Laboratory Exercise 5
Laboratory Exercise 5 Bus Communication The purpose of this exercise is to learn how to communicate using a bus. In the designs generated by using Altera s SOPC Builder, the Nios II processor connects
Laboratory Exercise 9
Laboratory Exercise 9 Figure 1 shows a digital system that contains a number of -bit registers, a multiplexer, an adder/subtracter unit, a counter, and a control unit. Data is input to this system via
Experiment 18 Full Adder and Parallel Binary Adder
Objectives Experiment 18 Full Adder and Parallel Binary Adder Upon completion of this laboratory exercise, you should be able to: Create and simulate a full adder in VHDL, assign pins to the design, and
Chapter 2: Hardware Design Flow Using Verilog in Quartus II
Chapter 2: Hardware Design Flow Using Verilog in Quartus II 2.1 Introduction to Quartus II System Development Software This chapter is an introduction to the Quartus II software that will be used for analysis
NOTE: This tutorial contains many large illustrations. Page breaks have been added to keep images on the same page as the step that they represent.
CSE 352 Tutorial # 4 Synthesizing onto an FPGA Objectives This tutorial will walk you through the steps of implementing a design made in Active-HDL onto the Altera Cyclone II FPGA NOTE: This tutorial contains
DKAN0011A Setting Up a Nios II System with SDRAM on the DE2
DKAN0011A Setting Up a Nios II System with SDRAM on the DE2 04 November 2009 Introduction This tutorial details how to set up and instantiate a Nios II system on Terasic Technologies, Inc. s DE2 Altera
SCHEMATIC DESIGN IN QUARTUS
SCHEMATIC DESIGN IN QUARTUS Consider the design of a three-bit prime number detector. Figure 1 shows the block diagram and truth table. The inputs are binary signals A, B, and C while the output is binary
ECE 353 Lab 4. MIDI Receiver in Verilog. Professor Daniel Holcomb UMass Amherst Fall 2016
ECE 353 Lab 4 MIDI Receiver in Verilog Professor Daniel Holcomb UMass Amherst Fall 2016 Timeline and Grading for Lab 4 Lectures on 11/15 and 11/17 Due on 12/12 Demos in Duda hall Schedule will be posted
EXPERIMENT NUMBER 7 HIERARCHICAL DESIGN OF A FOUR BIT ADDER (EDA-2)
7-1 EXPERIMENT NUMBER 7 HIERARCHICAL DESIGN OF A FOUR BIT ADDER (EDA-2) Purpose The purpose of this exercise is to explore more advanced features of schematic based design. In particular you will go through
Using Library Modules in VHDL Designs. 1 Introduction. For Quartus II 12.1
Using Library Modules in VHDL Designs For Quartus II 12.1 1 Introduction This tutorial explains how Altera s library modules can be included in VHDL-based designs, which are implemented by using the Quartus
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory.
PRELAB! Read the entire lab, and complete the prelab questions (Q1- Q3) on the answer sheet before coming to the laboratory. 1.0 Objectives In this lab you will get familiar with the concept of using the
DE2 Board & Quartus II Software
January 23, 2015 Contact and Office Hours Teaching Assistant (TA) Sergio Contreras Office Office Hours Email SEB 3259 Tuesday & Thursday 12:30-2:00 PM Wednesday 1:30-3:30 PM contre47@nevada.unlv.edu Syllabus
EE 231 Fall EE 231 Lab 2
EE 231 Lab 2 Introduction to Verilog HDL and Quartus In the previous lab you designed simple circuits using discrete chips. In this lab you will do the same but by programming the CPLD. At the end of the
Lab 3. Advanced VHDL
Lab 3 Advanced VHDL Lab 3 Advanced VHDL This lab will demonstrate many advanced VHDL techniques and how they can be used to your advantage to create efficient VHDL code. Topics include operator balancing,
Laboratory Exercise 1
Laboratory Exercise 1 Switches, Lights, and Multiplexers The purpose of this exercise is to learn how to connect simple input and output devices to an FPGA chip and implement a circuit that uses these
Experiment 8 Introduction to VHDL
Experiment 8 Introduction to VHDL Objectives: Upon completion of this laboratory exercise, you should be able to: Enter a simple combinational logic circuit in VHDL using the Quartus II Text Editor. Assign
Digital Circuit Design Using Xilinx ISE Tools
Digital Circuit Design Using Xilinx ISE Tools Poras T. Balsara and Prashant Vallur Table of Contents 1. Introduction 2. Programmable logic devices: FPGA and CPLD 3. Creating a new project in Xilinx Foundation
CSE P567 - Winter 2010 Lab 1 Introduction to FGPA CAD Tools
CSE P567 - Winter 2010 Lab 1 Introduction to FGPA CAD Tools This is a tutorial introduction to the process of designing circuits using a set of modern design tools. While the tools we will be using (Altera
Using Library Modules in VHDL Designs
Using Library Modules in VHDL Designs This tutorial explains how Altera s library modules can be included in VHDL-based designs, which are implemented by using the Quartus R II software. Contents: Example
CCE 3202 Advanced Digital System Design
CCE 3202 Advanced Digital System Design Lab Exercise #2 This lab exercise will show you how to create, synthesize, and test a 3-bit ripple counter. A ripple counter is simply a circuit that outputs the
Using Library Modules in VHDL Designs
Using Library Modules in VHDL Designs This tutorial explains how Altera s library modules can be included in VHDL-based designs, which are implemented by using the Quartus R II software. Contents: Example
Introduction to the Altera SOPC Builder Using Verilog Design
Introduction to the Altera SOPC Builder Using Verilog Design This tutorial presents an introduction to Altera s SOPC Builder software, which is used to implement a system that uses the Nios II processor
Using Library Modules in Verilog Designs. 1 Introduction. For Quartus II 13.0
Using Library Modules in Verilog Designs For Quartus II 13.0 1 Introduction This tutorial explains how Altera s library modules can be included in Verilog-based designs, which are implemented by using
EE 1315 DIGITAL LOGIC LAB EE Dept, UMD
EE 1315 DIGITAL LOGIC LAB EE Dept, UMD EXPERIMENT # 1: Logic building blocks The main objective of this experiment is to let you familiarize with the lab equipment and learn about the operation of the
Field Programmable Gate Array
Field Programmable Gate Array System Arch 27 (Fire Tom Wada) What is FPGA? System Arch 27 (Fire Tom Wada) 2 FPGA Programmable (= reconfigurable) Digital System Component Basic components Combinational
Laboratory Exercise 4
Laboratory Exercise Input/Output in an Embedded System The purpose of this exercise is to investigate the use of devices that provide input and output capabilities for a processor. There are two basic
Embedded Systems. "System On Programmable Chip" Design Methodology using QuartusII and SOPC Builder tools. René Beuchat LAP - EPFL
Embedded Systems "System On Programmable Chip" Design Methodology using QuartusII and SOPC Builder tools René Beuchat LAP - EPFL rene.beuchat@epfl.ch 3 Tools suite Goals: to be able to design a programmable
Embedded Systems. "System On Programmable Chip" Design Methodology using QuartusII and SOPC Builder tools. René Beuchat LAP - EPFL
Embedded Systems "System On Programmable Chip" Design Methodology using QuartusII and SOPC Builder tools René Beuchat LAP - EPFL rene.beuchat@epfl.ch 3 Tools suite Goals: to be able to design a programmable
Chapter 13 Programmable Logic Device Architectures
Chapter 13 Programmable Logic Device Architectures Chapter 13 Objectives Selected areas covered in this chapter: Describing different categories of digital system devices. Describing different types of
CCE 3202 Advanced Digital System Design
CCE 3202 Advanced Digital System Design Lab Exercise #2 Introduction You will use Xilinx Webpack v9.1 to allow the synthesis and creation of VHDLbased designs. This lab will outline the steps necessary
Quartus II Introduction Using Verilog Design
Quartus II Introduction Using Verilog Design This tutorial presents an introduction to the Quartus R II CAD system. It gives a general overview of a typical CAD flow for designing circuits that are implemented
COSC 3215 Embedded Systems Laboratory
COSC 3215 Embedded Systems Laboratory Lab 5 The Altera, Verilog and QuartusII Introduction This lab is an introduction to the Altera FPGA development board and the accompanying FPGA programming environment
EE 367 Logic Design Lab #1 Introduction to Xilinx ISE and the ML40X Eval Board Date: 1/21/09 Due: 1/28/09
EE 367 Logic Design Lab #1 Introduction to Xilinx ISE and the ML40X Eval Board Date: 1/21/09 Due: 1/28/09 Lab Description Today s lab will introduce you to the Xilinx Integrated Software Environment (ISE)
1 Introduction 2. 2 Background 3. 3 Getting Started 4. 4 Starting a New Project 6. 5 Design Entry Using VHDL Code 13
Quartus Prime Introduction Using VHDL Designs For Quartus Prime 17.0 Contents 1 Introduction 2 2 Background 3 3 Getting Started 4 3.1 Quartus Prime Online Help................................................................................................
University of Florida EEL 3701 Drs. Eric M. Schwartz & Karl Gugel. Quartus ROM Creation Instructions (in Quartus Prime Lite 17.1)
Page 1/5 Problem: You have an ASM or CPU that you would like to control/test from a ROM (EEPROM or Flash). How can you simulate the ROM under Quartus? Solution: Pick a device that has memory, e.g., Cyclone
The development board used in this class is ALTERA s DE The board provides the following hardware:
Lab 1 The goal of this lab is to get familiar with the mechanics of designing digital systems using VHDL and ALTERA s FPGAs. The development board used in this class is ALTERA s DE2-115. The board provides
Programmable Logic Design Techniques I
PHY 440 Lab14: Programmable Logic Design Techniques I The design of digital circuits is a multi-step process. It starts with specifications describing what the circuit must do. Defining what a circuit
LAB 2: INTRODUCTION TO LOGIC GATE AND ITS BEHAVIOUR
LAB 2: INTRODUCTION TO LOGIC GATE AND ITS BEHAVIOUR OBJECTIVE 1. To verify the operation of OR, AND, INVERTER gates 2. To implement the operation of NAND and NOR gate 3. To construct a simple combinational
Design Flow Tutorial
Digital Design LU Design Flow Tutorial Jakob Lechner, Thomas Polzer {lechner, tpolzer}@ecs.tuwien.ac.at Department of Computer Engineering University of Technology Vienna Vienna, October 8, 2010 Contents
Introduction to the Altera SOPC Builder Using Verilog Designs. 1 Introduction
Introduction to the Altera SOPC Builder Using Verilog Designs 1 Introduction This tutorial presents an introduction to Altera s SOPC Builder software, which is used to implement a system that uses the