This is intended as a quick reference guide to some of the features used in:

Transcription

1 Quick Reference Guide This is intended as a quick reference guide to some of the features used in: Garmin asecamp This is a guide only please refer to the relevant manuals for full details or ask professional advice if in doubt. This is the writer(s) interpretation of the required steps only and does not take any liability for the accuracy of the information supplied in this publication and it is supplied as is. Trade marks and copyright belong to the software/equipment manufacturers.

2 Document Revisions Amendment No. Amendment y Date - Original Document Joth 21 Sept 201 A Pages and 6 added Joth 22 Sept 201 C/D Images made larger on page 1 & correction to text in the document Trade Marks added and document cover / revisions Kev / Piers 24 Sept 201 Kev / Piers 2 Sept 201

3 Setup and Configuration efore using configure the following functions to enable ease of use : Enable the Toolbars : Select View then the Toolbars menus and Enable the toolbars as shown. Note: The tool bars may be in a different order, you can reorder them by dragging them. 2. Enable the Map Controls : Select View then the Map Controls menus and select the On option. Notes: This will allow you to zoom in/out and navigate around the map. 3. Enable the Over View Map Ctrl+1 : Select View then Map Views menus and select the Overview Map option. Notes: The over view map will toggle between visible /hidden. y holding down the Ctrl button on the keyboard and pressing 1 will have the same effect. 4. Customise the Options : Select Edit then Options menus. Click the Measurement Icon - Update the UOM. Click the Activity Profile Icon Select Motorcycling then Routing tab & change as required. Click on the Speed utton (Located at the bottom of the Routing Tab screen) Set realistic Speeds (to reflect achievable route times) Note: It is recommended to have the Sat NAV connected to the PC/Laptop before planning routes using.(unless maps are on the PC) Ensure your Maps on the SAT NAV are the same as Maps - On the Zumo Select Tools Settings Map - Map Info (i.e. CN Europe NT and also 3D Maps) - On software see the Maps Products on the Tool ar (i.e. City Navigator Europe NT201.4 (Note the missing 0 at the end) Page 1

4 Library uses a library to store all your Routes, Way Points & Tracks etc 1 2 3a 3b 1. List Folders are used to group and catalogue different types of routes etc. Note: Right Click on My Collection and select Enter a name i.e. MW Rides and press enter. 2. Lists are used to store routes, waypoints associated with a particular ride or trip etc.. Note: Right Click on a List Folder select Enter a name i.e. Saltburn 201 and press enter. 3a. User Data: User data (Routes, Way Points etc.) for each List are displayed at the bottom left of the screen. 3b. Note: Click on the icons at the bottom of the screen to toggle between types of User Data. Display all Data Display Way Points Only (Waypoints are stopping points or places to pass on a route) Display Routes Only Display Tracks Only (Routes are a collection of Way Points) (Tracks can be imported from your SAT NAV and show your actual route & times etc.) Page 2

5 Navigating the Map has various ways of Navigating the Map Map Controls Use the Map Controls to Zoom in and Out using the slider or click on the arrows to scroll the map Note: If you accidentally rotate the map click on or Press Ctrl+N keys to return North to the top. 2. Overview Map Click and hold the left mouse button down over the Overview Map and drag the highlighted rectangle around the Overview area. 3. Pan Icon Click on the Pan Icon then hold the Left Mouse utton down over the main map and drag the the map, release the mouse button when finished. 4. Zoom Icon and Detail Level Click on the Zoom Icon Click and hold down the Left Mouse utton on the map, drag the mouse over the required area and release the mouse button (the map will zoom into the selected area). To view more detail ( roads / POI s) etc. use the Detail Level dropdown in the tool bar.. Map Edges If you place the mouse pointer at the corners or centre of the edges you can click and scroll the map. 6. Mouse / Keyboard You can use the scroll wheel on the mouse to zoom the map in and out. You can use the keys on the Keyboard to navigate the Map Pan Up/Down/Left/Right Zoom = In (+) / Out(-) Page 3

6 Searching and Creating Waypoints (POI s) General 1) Click on the blue search button at the top right of the screen. 2) Activate the 3 Icons highlighted in a blue box. The Points of Interest box shows closest points to the centre of the screen. The Addresses box will show Addresses after a search. The User Data box shows user data in the selected List / Folder Selected. 3) To change search options click on the Open Find Options Icon General Search A) Type the search string into the box at the top right of ) Click the lue Search button C) Results will be shown in the boxes below the search box. D) Select the required result in one of the boxes to show on the map. E) Click the popup red flag to make it a waypoint. E C A 2. Search for Points of Interest (POI) A) Click on the Open Find Options at the top right of the screen. ) Click on the Points of Interest Radio utton. C) Enter a Location (if required) that you want to search around D) Select what type of POI s you want to find E) Press Search F) Click/Select the required POI to show it on the map A D C E F 3. Search for a Post Code (or Address / Intersection) A) Click on the Open Find Options at the top right of the screen. A ) Click on the Addresses Radio utton. C) Click on the Postal Code Radio utton. E Note: Select Address / Intersection / Post Code for different searches C D) Enter a Post Code and Select it from the drop down box. D E) Press Search F) Click/Select the required post code to show it on the map G) Click the red flag to make it a way point and it will be added to your user list data Note: the search box will change when you search to reflect the options clear the box to start again. G F 4. Find a Map location from Latitude/Longitude Coordinates A) Click on the menus Find then Locate Coordinates ) Enter the Coordinates and click on Recenter. C) Click Create Waypoint to insert a waypoint into your List. Waypoints y clicking on Red Flags in various screens or on the tool bar you create waypoints which will be added to your User Data List. A) Right click on a waypoint in the list to Open/Edit etc. ) To move a waypoint right click on the waypoint on the map Select Move Waypoint and click on the map where you want it to move to. A Note: Other options are available under both popup menus.. Page 4

7 Creating and Editing Routes 1. Introduction can produce custom routes in various ways, (by creating Waypoints and joining them up with the Route Tool ) the Icons required can be found on the toolbar or in the Edit and Tools Menus, below is example of how to create and edit routes.. Creating a route. (i.e. Home to Matlock ath to arton Marina) Step 1. Create or Select a List Folder and List from the Library where the Waypoints and Routes will be saved. Step 2. Create Waypoints for the Start (Home), Intermediate stop(s) (Matlock ath) and the Finish (arton Marina) Note: The way points will be shown in the User Data box (bottom left of the screen). Step 3. Click on the following menus Edit then Create Route menus Note: Check that you have the correct maps in use and the Activity profile is Motorcycling. Step 4. Drag the Start Waypoint from the User box to the Start ox and the Finish Waypoint to the Destination ox and click Go Note: The route is added to the User Data ox and the route editor will be displayed. Step. After clicking Go the route edit box will be shown Click on the Finish Line i.e. arton Marina Click on the on the right of the route properties window Select the Intermediate way point i.e. Matlock ath Click on Insert Waypoint. Waypoints can be reordered by clicking on them and using the up and down icons Exit the screen when finished Note: the details will be saved automatically. 2. Add additional intermediate stops. Step 1. Create additional Waypoints Step 2. Double click the Route in the User Data box and add the Waypoints in the route where required. (see step above) 3. Change the route (Add a Waypoint Visually). The route currently goes mainly down the A38 so we will want to alter the route via a more scenic route, We will add a Waypoint Visually to go via Ashbourne Step 1. Click the Route in the User Data box and then select the Insert Icon. Step 2. Click somewhere on the Route between Matlock ath and arton Marina Step 3. Click on the A1 where it leaves Ashbourne and the Route will recalculate off the A38 via the Waypoint. 4. Change the route (Move a Way point Visually). We will change the Ashbourne Waypoint to go Via uxton for a wander through the Peak District Step 1. Click the Route in the User Data box and select the Move Icon. Step 2. Hold the Left mouse button down on the WayPoint inserted at Ashbourne, move the Mouse to uxton and release the mouse button, the route will re calculate. Change the route (Erase a Way point Visually). Step 1. Click the Route in the User Data box and Select the Erase icon 6. Change the route (Divide a long route into two routes). Step 1. Click the Route in the User Data box select the Divide icon Divided answer any popup questions and click ok if required. click on a way point to erase it. click on route where you want it Note: Routes can be renamed by double clicking on a route in the User Data box and entering a new name at the top of the popup properties window. Rename routes starting the description with etc so they show in order in and on the SAT NAV unit. Page

8 Exporting and Importing User Data (.gdb and.gpx) 1. Exporting All Routes and Waypoints in a List to a file Select the List required i.e. Saltburn 201, Click on the File - Export Export Saltburn 201 menus Select a location to save the file i.e. Desktop Enter a file name and Select GPS exchange Format (*.gpx) from the list and click the Save utton Note: A GPX file can be shared between different makes of SAT NAV a GD is Garmin specific 2. Exporting Selected Routes and Waypoints from a List to a file Select the List required i.e. Saltburn 201 then select the User Data required from the bottom list Click on the File -Export Export Selection menus Select a location to save the file i.e. Desktop Enter a file name and Select GPS exchange Format (*.gpx) from the list and click the Save utton Note: A GPX file can be shared between different makes of SAT NAV a GD is Garmin specific 3. Importing Routes and Waypoints from a File Create a new List or Select an existing List i.e. Saltburn 201 (If you select a List folder then a new list will be created) Click on the File Import into Saltburn 201 menus ( Saltburn 201 will be replaced with your selected List or Folder) Select the file to be imported (if the file is received in an save the attached file to your desktop before importing) Click Open and the file content will be loaded into your selected location in the Library. Note: Recalculate the routes when imported to make sure they are compatible with your map version. Page 6

9 Send and Receive user data to a Zumo SAT NAV 1. Sending AllRoutes and Waypoints in a Listto the SAT NAV Select the List required i.e. Saltburn 201, Click on the menus Device Send to Device Send Saltburn 201 to Device Select if you want them to be saved on the Device or Memory Card (oth Options work) and Click Ok The Devices Listing shows the User Data transferring and a Green tick will appear when finished. When you put the back cover on the Zumo and it restarts it will ask you to Import now select Yes. 2. Sending Selected Routes and Waypoints to the SAT NAV Select the List required i.e. Saltburn 201 then select the User Data required from the bottom list. Click on the menus Device Send to Device Send Selection to Device Select if you want them to be saved on the Device or Memory Card (oth Options work) and Click Ok The Devices Listing you show the User Data transferring and a Green tick will appear when finished. When you put the back cover on the Zumo and it restarts it will ask you to Import now select Yes. Note: Routes will be displayed in Custom Routes and Waypoints in Favourites on the SAT NAV Unit if transferred. 3. Receive Routes, Waypoints and Tracks from a SAT NAV Click on the menus Device Receive from Device Select the SAT NAV Internal Memory and Click OK The Routes, Waypoints and Tracks will be saved into the Data Received from Zumo List Folder. You can filter out the Tracks (where you have been) by selecting the Show Tracks icon. Page 7

10 END OF QUICK GUIDE Page 8