Metasys Integrator GE Lighting Application

Transcription

1 Metasys Connectivity Technical Manual Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator GE Lighting Application lntroduction Page 3 Application Details *3 Component Requirements *5 Vendor Contact Information *6 Design Considerations *7 Cable Connections 9 Cable Pinouts *9 Connecting the Cable 10 Metasys Integrator Setup *11 Point Mapping Tables 13 Total Lighting Control Panel *13 GE ECON Lighting Control Panel 13 Metasys Network Setup 15 Mapping to a CS Object *15 Custom Integration *17 * indicates those sections where changes have occurred since the last printing Johnson Controls, Inc. 1 Code No. LIT

2 2 Metasys Integrator Metasys Integrator GE Lighting Application

3 lntroduction This document explains Metasys Integrator GE lighting applications, which include: Total Lighting Control System GE ECON Lighting Control Panel Use this document with the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5), which provides information on installing and commissioning Metasys Integrator. For information on vendor equipment, see GE documentation (obtainable from a GE representative), or call Application Details Metasys Integrator allows GE equipment to become an integral part of the Metasys and Metasys Companion Networks. Once the Total Lighting Control System or GE ECON Lighting Control Panel is connected to a Metasys or Companion Network via the Metasys Integrator, its data is available to the full complement of Metasys Facility Management System (FMS) features, including Change-of-State (COS) monitoring, alarm notification, trend, and totalization. The Total Lighting Control (TLC) panel consists of up to 48 relays that provide on/off control of lighting circuits and other switchable loads. The RLINK Dataline Access Module unit acts as an interface between TLC panels and other devices (such as Metasys Integrator). Metasys Integrator allows status information and commands to be transmitted between the TLC panel and the Metasys or Companion Networks via the RLINK unit. Each Metasys Integrator vendor port can connect to one GE RLINK unit. One RLINK unit can connect up to 499 TLC panels. Note: The limit on the number of devices Metasys Integrator can connect to is 256. Other system limits may restrict the number of points which may be mapped back through a single Metasys Integrator panel. The GE ECON Lighting Control panel is a central controller that can control up to 9999 lighting control group sectors in multiple GE lighting panels on the GE network. Figure 1 shows the GE ECON Lighting Control Panel and Metasys integration. Figure 2 shows the GE TLC System and Metasys Companion integration. Metasys Integrator Metasys Integrator GE Lighting Application 3

4 N1 LAN Standard NCU RS-232 GE ECON Panel GE RS-485 Dataline Metasys Integrator GE Panel GE Panel GE Panel UNT N2 Bus GE1b Figure 1: GE and Metasys Integration Panel Unit M3 Workstation Dataline Power Supply Metasys Integrator RS-232 RLINK Dataline Access Module Proprietary RS-485 (2-wire) GE TLC Panel No. 1 GE TLC Panel No. 256 UNT N2 Bus Note: A PC version and converter may be substituted for the Panel unit. gecomp2 Figure 2: GE and Metasys Companion Integration 4 Metasys Integrator Metasys Integrator GE Lighting Application

5 Component Requirements Total Lighting Control Panel GE ECON Lighting Control Panel To integrate the GE Total Lighting Control System, you need the following: properly installed RLINK Dataline Access Module, Dataline Power Supply, and Total Lighting Control Panel RS-232 cable (RCABLE-C provided by GE to connect the GE RLINK unit to Metasys Integrator) Metasys Integrator N2 Bus (for connecting Metasys Integrator to the Metasys or Companion Network) portable PC for downloading vendor communication tables (.VCT files) and network setup information, and for running diagnostics cable for connecting portable PC to Metasys Integrator the correct vendor communication table (.VCT file) to download into Metasys Integrator (supplied on diskette) To integrate the GE ECON Lighting Control Panel, you need the following: properly installed GE ECON Lighting Control Panel and GE lighting panels RS-232 cable (for connecting the GE ECON to Metasys Integrator) GE RS-485 Dataline (for connecting the GE ECON to the other GE lighting panels) Metasys Integrator N2 Bus (for connecting Metasys Integrator to the Metasys or Companion Network) portable PC for downloading vendor communication tables (.VCT files) and network setup information, and for running diagnostics cable for connecting portable PC to Metasys Integrator the correct vendor communication table (.VCT file) to download into Metasys Integrator (supplied on diskette) Metasys Integrator Metasys Integrator GE Lighting Application 5

6 This document describes the RS-232 cable and the vendor communication tables. GE documentation describes their equipment. The remaining components are described in the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5). Metasys Release Requirements Metasys Companion Release Requirements Vendor Component Requirements Vendor Contact Information To integrate the GE Total Lighting Control System or GE ECON Lighting Control Panel into the Metasys Network, you need: Metasys Operator Workstation (OWS) software Release 9.0 or higher Metasys Integrator software/firmware Release 7.0 or higher To integrate the GE Total Lighting Control System or GE ECON Lighting Control Panel into the Metasys Companion Network, you need: Metasys Companion Release 6.0 or higher Metasys Integrator software/firmware Release 7.0 or higher Integration between Metasys Integrator and GE has been tested with: Total Lighting Control Panel Revision 1.0 (Catalog No. RINTER1212) with built-in controller (Catalog No. RCC48, hardware Revision D, software Revision 2.0) and the RLINK Dataline Access Module Revision 1.0 (Catalog No. RLINK) GE ECON Lighting Control Panel Revision VS.2.02D (Catalog No. ECONRS232L1) connected to GE lighting panels Changes to this equipment or integration of GE products not discussed in this document will require additional software development and testing. For information on integrating other products, refer to the Custom Integration section of this technical bulletin. GE Electrical Lighting Control 370 Green Valley Rd. Birmingham, AL Customer Service Phone: (800) (800-TLC-ASST) FAX: (205) Metasys Integrator Metasys Integrator GE Lighting Application

7 Design Considerations When integrating GE equipment, consider the following: Make sure GE equipment is set up and running properly before integrating with Metasys or Companion. (The GE representative is responsible for operation of GE equipment.) RS-232 cable distance between Metasys Integrator and the GE equipment can be a maximum of 50 feet. For the GE TLC Panel, make sure the equipment s baud rate is set to (The GE representative is responsible for setting the baud rate.) The GE TLC Panels have their own internal programs for lighting schedules. You must erase these schedules in order for Metasys to properly maintain a lighting schedule. The GE TLC Panel sends out an asynchronous Change-of-State message when a relay changes state. Metasys Integrator does not currently handle asynchronous messages; therefore, the messages are ignored. The change will be detected when polled. One vendor address must be defined for the RLINK. This allows a 10-second delay each polling sequence, allowing time for any TLC panels which had been powered down to re-initialize. For the GE ECON Lighting Control Panel, make sure the equipment s baud rate is set at (The GE representative is responsible for setting the baud rate.) If the GE ECON front panel key is in Manual state, all the points will be offline until the key is returned to Automatic. Metasys Integrator Metasys Integrator GE Lighting Application 7

8 8 Metasys Integrator Metasys Integrator GE Lighting Application

9 Cable Connections Cable Pinouts GE RLINK Use the following cable pinouts for the RS-232 connection between Metasys Integrator and the GE RLINK device: Vendor Port A or B on Metasys Integrator DB-9 Female RS-232 Port on GE RCABLE-C DB-9 Male Signal RD TD DTR GND DSR CTS Pin RS-232 Pin Signal RD TD DTR GND DSR CTS (50 ft. maximum) GE6b Figure 3: Cable Pinouts GE RLINK GE ECON Use the following cable pinouts for the RS-232 connection between Metasys Integrator and the GE ECON device: Vendor Port A or B on Metasys Integrator DB-9 Female RS-232 Connector on GE ECON DB-25 Male Signal DCD RD TD DTR GND DSR RTS CTS Pin RS-232 Standard "AT" Cable Pin Signal DCD RD TD DTR GND DSR RTS CTS (50 ft. maximum) GE7 Figure 4: Cable Pinouts GE ECON Device Metasys Integrator Metasys Integrator GE Lighting Application 9

10 Connecting the Cable Connect one end of the RS-232 cable to either Vendor Port A or Vendor Port B on the Metasys Integrator. Connect the other end to the RS-232 Port on the GE RLINK or ECON. Metasys Integrator GE RLINK or ECON Vendor Port A or B RS-232 Cable RS-232 Port GE3b Figure 5: Port to Port Connection for RLINK or ECON 10 Metasys Integrator Metasys Integrator GE Lighting Application

11 Metasys Integrator Setup To set up Metasys Integrator, use a portable PC connected to Metasys Integrator Terminal Port. Metasys Integrator setup involves: downloading the correct vendor communication table (.VCT file) setting up the ports setting up the network addressing The following table provides information specific to the GE application. For detailed procedures, see the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5). Table 1: Metasys Integrator Setup for GE Vendor Communication Table (.VCT File) Total Lighting Control Panel GE ECON Lighting Control Panel Port Setup-- Total Lighting Control Panel Baud Rate 9600 Word Length 8 Stop Bits 1 Parity Interface GE_TLC.VCT GE_RLINK.VCT GE_ECON.VCT None RS-232 Port Setup--GE ECON Lighting Control Panel Baud Rate 1200 Word Length 7 Stop Bits 1 Parity Interface Even RS-232 Network Setup--Total Lighting Control System Vendor Address TLC RLINK Timeout Value Poll Delay TLC RLINK Continued on next page ms 55 ms 10,000 ms Metasys Integrator Metasys Integrator GE Lighting Application 11

12 Network Setup--GE ECON Lighting Control Panel (Cont.) Vendor Address Decimal sector block number 0-39 * Timeout Value Poll Delay Performance Guide (Cont.) 3000 ms 770 ms Approximate Scan Time (For a single N2 address) TLC Panel 1 second RLINK 10 seconds ECON Lighting Control Panel 2 seconds * Each block has up to 256 sectors. Example: to map the first 256 sectors, set the vendor address to Metasys Integrator Metasys Integrator GE Lighting Application

13 Point Mapping Tables Tables 2-4 (one for each application) show the points available for mapping in the GE devices. Total Lighting Control Panel To obtain the hardware reference for mapping points to a CS object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Relay 1 State point is BO1. Table 2: Total Lighting Control Panel NPT 1 NPA 2 Unit Description BI 1-48 Relay X Failed (X=NPA) 0=ok, 1=fail BO 1-48 Relay X State (X=NPA) 0=off, 1=on 1 Network Point Type 2 Network Point Address Table 3: GE RLINK NPT 1 NPA 2 Unit Description BI 1 RLINK Established 0=ok, 1=fail 1 Network Point Type 2 Network Point Address GE ECON Lighting Control Panel To obtain the hardware reference for mapping points to a CS object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Sector 1 State point is BO1. Table 4: GE ECON Lighting Control Panel NPT 1 NPA 2 Unit Description BO Sector X 3 State 4 0=off, 1=on 1 Network Point Type 2 Network Point Address 3 You need multiple Metasys Integrator addresses to control all 9984 sectors in a GE ECON panel. The sector number is determined by the following equation: sector = (Vendor Address * 256) + NPA For example, if your desired sector number is 522 and your vendor address is 2, determine the NPA as follows: 522 = (2 * 256) + NPA Therefore, your NPA would be There is no way to determine the actual sector state. The state displayed is the last command sent to the ECON panel by Metasys Integrator. Metasys Integrator Metasys Integrator GE Lighting Application 13

14 14 Metasys Integrator Metasys Integrator GE Lighting Application

15 Metasys Network Setup Metasys Network Setup is described in the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5). This section contains details specific to the GE applications. Mapping to a CS Object Table 5: Software Model and CS Object Details Application Software Model (on Models diskette) Display Attribute (recommended) NT Command Attribute (recommended) GE TLC GE_TLC.DDL BI1 BO1 Relay 1 Failed Relay 1 State GE ECON GE_ECON.DDL Any Any * For the NT Command attribute, use the same attribute as the Display attribute. However, since the points are not commandable, you will not be able to command the attribute. (This must be defined because the NT Command attribute cannot be null.) Metasys Integrator Metasys Integrator GE Lighting Application 15

16 16 Metasys Integrator Metasys Integrator GE Lighting Application

17 Custom Integration For information on integrating products which are not discussed in this document, first refer to the Metasys Compatible Global Catalog, an online list of released Connectivity products. If this list does not provide the information you require, consider using the System Integration Project Data Sheet to request a custom contract from the System Integration Team. Both the Metasys Compatible Global Catalog and the System Integration Project Data Sheet can be accessed from The Advisor by performing the following steps: 1. Click on the Products button located on the left side of The Advisor home page. 2. Click on the Product Literature link. 3. Click on the Metasys link. 4. Click on the Sales button. 5. Click on the Connectivity Sales Resource Manual FAN 629 link. 6. Find the System Integration Project Data Sheet link in the table of contents. Click on this link to view an online copy of the System Integration Project Data Sheet, or click on the Metasys Compatible Global Catalog link below it to view a list of released Connectivity products. The System Integration Project Data Sheet (LIT ) can also be found in the Metasys Connectivity Sales Resource Manual (FAN 629). If you need further assistance, contact Johnson Controls Field Support Services. Metasys Integrator Metasys Integrator GE Lighting Application 17

18 Notes 18 Metasys Integrator Metasys Integrator GE Lighting Application

19 Notes Metasys Integrator Metasys Integrator GE Lighting Application 19

20 Notes Controls Group FAN E. Michigan Street Metasys Connectivity Technical Manual P.O. Box 423 Metasys Integrator Release 8.0 Milwaukee, WI Printed in U.S.A Metasys Integrator Metasys Integrator GE Lighting Application