Metasys Integrator Multistack Application

Transcription

1 Metasys Connectivity Technical Manual Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator Multistack Application lntroduction Page *3 Application Details *3 Component Requirements *5 Vendor Contact Information 6 Design Considerations 6 Cable Connections 7 Cable Pinouts 7 Connecting the Cable 7 Metasys Integrator Setup *9 Point Mapping Table 11 Metasys Network Setup *13 Mapping to a CS Object 13 Custom Integration *15 * Indicates those sections where changes have occurred since the last printing Johnson Controls, Inc. 1 Code No. LIT

2 2 Metasys Integrator Metasys Integrator Multistack Application

3 lntroduction This document explains the Metasys Integrator Multistack application. Use this document with the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5), which provides information on installing and commissioning Metasys Integrator. For information on vendor equipment, see Multistack documentation (obtainable from a Multistack representative). Application Details Metasys Integrator allows Multistack equipment to become an integral part of the Metasys and Metasys Companion Networks. Once a Multistack Modular Liquid Chiller is connected to a Metasys or Companion Network via the Metasys Integrator, its data is available to the full complement of Metasys Facility Management System (FMS) features, including Change-of-State (COS) monitoring, alarm notification, trend, and totalization. Up to 12 Multistack Modules can be connected together to create a chiller system. A Master Controller collects data from each of the connected chillers, and allows information and commands to be transmitted between chillers and non-multistack devices (such as Metasys Integrator). Each Metasys Integrator vendor port can connect to one Master Controller. Figure 1 shows Multistack and Metasys integration, and Figure 2 shows Multistack and Metasys Companion integration. Metasys Integrator Metasys Integrator Multistack Application 3

4 N1LAN Standard NCU RS-232 Master Controller Metasys Integrator Multistack Module Multistack Module Multistack Module Multistack Module UNT N2 Bus MULTI1 Figure 1: Multistack Modular Chillers and Metasys Integration Panel Unit M3 Workstation RS-232 Master Controller Metasys Integrator Multistack Module Multistack Module Multistack Module UNT N2 Bus Note: A PC version and converter may be substituted for the Panel unit. multcomp Figure 2: Multistack Modular Chillers and Metasys Companion Integration 4 Metasys Integrator Metasys Integrator Multistack Application

5 Component Requirements Metasys Release Requirements Metasys Companion Release Requirements Vendor Component Requirements To integrate Multistack Modular Chillers, you ll need the following: properly installed Master Controller and Multistack Modular Chillers RS-232 cable (for connecting the Multistack Modular Liquid Chiller to Metasys Integrator) Metasys Integrator N2 Bus (for connecting Metasys Integrator to the Metasys or Companion Network) portable PC for downloading vendor communication tables (.VCT files) and network setup information, and for running diagnostics cable for connecting portable PC to Metasys Integrator the correct vendor communication table (.VCT file) to download into Metasys Integrator (supplied on diskette) This document describes the RS-232 cable and the vendor communication tables. Multistack documentation describes their equipment. The remaining components are described in the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5). To integrate Multistack equipment into the Metasys Network, you ll need: Metasys Operator Workstation (OWS) software Release 4.0 or higher Metasys Integrator software/firmware Release 2.0 or higher To integrate Multistack equipment into the Metasys Companion Network, you ll need: Metasys Companion Release 4.0 or higher Metasys Integrator software/firmware Release 2.0 or higher RS-232 communication chip installed in Socket U34, next to the battery, marked HD6350 Integration between Metasys Integrator and Multistack has been tested with the Multistack Modular Liquid Chiller. Changes to this equipment or integration of Multistack products not discussed in this document will require additional software development and testing by Systems Products. For information on integrating other products, refer to the Custom Integration section in this technical bulletin. Metasys Integrator Metasys Integrator Multistack Application 5

6 Vendor Contact Information Design Considerations Multistack, Inc. 365 South Oak Street West Salem, WI Technical Support Phone: (608) FAX: (608) When integrating Multistack, consider the following: Make sure Multistack equipment is set up and running properly before integrating with Metasys or Companion. (The Multistack representative is responsible for operation of Multistack equipment.) The Master Controller baud rate is set to 2400 and is not adjustable. RS-232 cable distance between Metasys Integrator and the Master Controller can be a maximum of 50 feet. 6 Metasys Integrator Metasys Integrator Multistack Application

7 Cable Connections Cable Pinouts Use the following cable pinouts for the RS-232 connection between Metasys Integrator and the Multistack Master Controller: Vendor Port A or B on Integrator DB-9 Female RS-232 Port on Master Controlle DB-25 Male Signal RD TD GND Pin RS-232 (50 ft. maximum) Pin Signal Rx Tx GND MULTI2 Figure 3: Cable Pinouts Connecting the Cable Connect the female end of the RS-232 cable to either Vendor Port A or Vendor Port B on Metasys Integrator. Connect the male end to the Other Output Port (RS-232 Serial) on the Multistack Master Controller. Metasys Integrator Multistack Master Controller Vendor Port A or B RS-232 Cable Other Output Port (RS-232 Serial) MULTI3 Figure 4: Port to Port Connection Metasys Integrator Metasys Integrator Multistack Application 7

8 8 Metasys Integrator Metasys Integrator Multistack Application

9 Metasys Integrator Setup To set up Metasys Integrator, you ll use a portable PC connected to Metasys Integrator Terminal Port. Metasys Integrator setup involves: downloading the correct vendor communication table (.VCT file) setting up the ports setting up the network addressing The following table provides information specific to the Multistack application. For detailed procedures, see the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5). Table 1: Metasys Integrator Setup for Multistack Modular Liquid Chillers Vendor Communication Table (.VCT FILE) Multistack Modular Liquid Chiller Port Setup Baud Rate 2400 Word Length 8 Stop Bits 1 Parity Interface Network Setup Vendor Address 0* Timeout Value Poll Delay Performance Guide MS_MCHIL.VCT None RS ms 55 ms Approximate Scan Time 9 seconds (For a single device) * Although Multistack Chillers do not use addressing, Metasys Integrator requires a value for this parameter. Metasys Integrator Metasys Integrator Multistack Application 9

10 10 Metasys Integrator Metasys Integrator Multistack Application

11 Point Mapping Table The following table shows the points available for mapping in the Multistack Modular Liquid Chiller: To get the hardware reference for mapping points to a CS object (via the software model), combine the NPT (Network Point Type) and NPA (Network Point Address). For example, the hardware reference for the Entering Chill Water Temperature point is 1. Table 2: Multistack Modular Liquid Chiller Points NPT 1 NPA 2 Unit Description DegF DegF DegF DegF % % # # # Entering Chill Water Temperature Leaving Chill Water Temperature Entering Condenser Water Temperature Leaving Condenser Water Temperature Capacity Demand Current Faults Lead Compressor Number Number of Compressors On BI 1 Chill Water Flow 0=ok, 1=fault BI 2 Condenser Water Flow 0=ok, 1=fault BI 3 Low Chill Water Temp 0=ok, 1=fault BI 4 Power Failure Unit 0=ok, 1=fault BI 5 Phase Failure Unit 0=ok, 1=fault AO AO AO DegF DegF % Upper Setpoint (Entering Chill Water) Lower Setpoint (Leaving Chill Water) Demand Limit Setpoint BO 1 Chiller Status 0=Off, 1=On 1 Network Point Type 2 Network Point Address Continued on next page... Metasys Integrator Metasys Integrator Multistack Application 11

12 NPT 1 (Cont.) NPA 2 Unit Description ADI 1 ADI 2 ADI 3 ADI 4 ADI 5 ADI 6 ADI 7 ADI 8 ADI 9 ADI 10 ADI 11 ADI 12 ADI 13 ADI 14 ADI 15 ADI 16 ADI 17 ADI 18 ADI 19 ADI 20 ADI 21 ADI 22 ADI 23 ADI 24 1 Network Point Type 2 Network Point Address 0-9% Capacity 10-19% Capacity 20-12% Capacity 30-39% Capacity 40-49% Capacity 50-59% Capacity 60-69% Capacity 70-79% Capacity 80-89% Capacity % Capacity Compressor 1 Status Compressor 2 Status Compressor 3 Status Compressor 4 Status Compressor 5 Status Compressor 6 Status Compressor 7 Status Compressor 8 Status Compressor 9 Status Compressor 10 Status Compressor 11 Status Compressor 12 Status Compressor 13 Status Compressor 14 Status Compressor 15 Status Compressor 16 Status Compressor 17 Status Compressor 18 Status Compressor 19 Status Compressor 20 Status Compressor 21 Status Compressor 22 Status Compressor 23 Status Compressor 24 Status Compressor Status 0 = Off 1 = On 2 = High Pressure Fault 3 = Low Pressure Fault 4 = Chill Water Temperature Fault 12 Metasys Integrator Metasys Integrator Multistack Application

13 Metasys Network Setup Metasys Network Setup is described in the Metasys Integrator Technical Bulletin (LIT ) in the Metasys Connectivity Technical Manual (FAN 629.5). This section contains details specific to Multistack applications. Mapping to a CS Object Table 3: Software Model and CS Object Definition Application Software Model (on Models diskette) Display Attribute (recommended) NT Command Attribute (recommended) Multistack Modular Liquid Chiller MS_MCHIL.DDL BO1 Chiller Status AO1 Entering Chill Water Metasys Integrator Metasys Integrator Multistack Application 13

14 14 Metasys Integrator Metasys Integrator Multistack Application

15 Custom Integration For information on integrating products which are not discussed in this document, first refer to the Metasys Compatible Global Catalog, an online list of released Connectivity products. If this list does not provide the information you require, consider using the System Integration Project Data Sheet to request a custom contract from the System Integration Team. Both the Metasys Compatible Global Catalog and the System Integration Project Data Sheet can be accessed from The Advisor by performing the following steps: 1. Click on the Products button located on the left side of The Advisor home page. 2. Click on the Product Literature link. 3. Click on the Metasys link. 4. Click on the Sales button. 5. Click on the Connectivity Sales Resource Manual FAN 629 link. 6. Find the System Integration Project Data Sheet link in the table of contents. Click on this link to view an online copy of the System Integration Project Data Sheet, or click on the Metasys Compatible Global Catalog link below it to view a list of released Connectivity products. The System Integration Project Data Sheet (LIT ) can also be found in the Metasys Connectivity Sales Resource Manual (FAN 629). Metasys Integrator Metasys Integrator Multistack Application 15

16 Notes Controls Group FAN E. Michigan Street Metasys Connectivity Technical Manual P.O. Box 423 Metasys Integrator Release 8.0 Milwaukee, WI Printed in U.S.A Metasys Integrator Metasys Integrator Multistack Application