Step 1: Analyze a Baseline Model
|
|
|
- Collin Booth
- 6 years ago
- Views:
Transcription
1 Step 1: Analyze a Baseline Model Let's start by opening the model and running a baseline analysis. Performing analysis on a model before setting up optimization helps ensure that any constraints and other parameters are reasonable. 1. Open the baseline_oilpan.stmod file located in the downloaded models folder. Note that it has a pressure applied to the base part and is restrained with fasteners at the bolt holes. 2. Click Run Analysis on the Analyze icon on the Structure ribbon. 3. Set the options in the Run Analysis window as shown below:
2 4. Change the Element size to 3 mm. 5. For Normal modes, select Number of modes: 3 and use supports from Load Case Make sure that Speed/Accuracy is set to Faster. 7. Click Run to perform the analysis. 8. When the run is complete, double-click on the name of the run to view the results. 9. In the Analysis Explorer, under the Show icons, select Hide all loads and supports. 10. Select Normal Modes for the load case and review the modes.
3 Step 2: Prepare the Model for Topography Optimization The best starting point for topography optimization is a design region without complex definition within the CAD. In many cases the Holes tool can be used to remove existing beads and fill in holes. 1. Select the Simplify tool on the Geometry ribbon. 2. Select the Holes tool. 3. Click the Clear Selection button on the guide bar. 4. Zoom in on one of the beads, and double-click one of the bottom fillets (nearest the bottom of the oil pan). This will chain select the entire bead.
4 5. Click on one of the selected red faces to remove the entire bead. 6. Repeat the procedure to remove the remaining beads on the oil pan. (Alternatively, you can open the defeatured_oilpan.stmod file located in the Tutorials folder in the installation directory.)
5 Step 3: Rerun the Analysis and Compare Results Now rerun the analysis with the same settings and compare the results with the baseline analysis from Step Click Run Analysis on the Analyze icon on the Structure ribbon. 2. Set the options in the Run Analysis window as shown below:
6 3. Change the Element size to 3 mm. 4. For Normal modes, select Number of modes: Make sure that Speed/Accuracy is set to Faster. 6. Click Run to perform the analysis. 7. When the run is complete, double-click on the name of the run to view the results. 8. In the Analysis Explorer, select Normal Modes for the load case and review the modes. Note that the local mode shape where the beads were removed dropped from 1076 Hz to 693 Hz.
7 Step 4: Run Topography Optimization The next step is to define the design space and run a topography optimization. 1. Right-click on the base part to open the context menu, and select Design Space.
8 2. Click Run Optimization on the Optimize icon on the Structure ribbon. 3. Set the options in the Run Optimization window as shown below: 4. Select Topography for the Run Type. 5. Select Maximize Stiffness for the Objective. 6. Set the following Bead Options: Minimum width: 3mm
9 Draw angle: 60 deg Maximum depth: 3mm 7. For Frequency Constraints, select Maximize frequencies and use supports from Load Case Select Faster for the Speed/Accuracy. 9. Click Run to perform the optimization. 10. When the run is complete, double-click on the name of the run to view the results. 11. In the Shape Explorer, note that Mode 1 has risen to 1343 Hz with a lower bead height than in the original part. Interpreting the results of topography optimization is often helped by performing multiple runs with different bead option parameters and bead patterns. This highlights key areas that benefit from the extra form and increased section modulus that typically result from topology optimization. Step 5: Apply Bead Patterns, Rerun, and Reanalyze the Model Linear, circular, and radial bead patterns are sometimes desired for manufacturing or other reasons. These bead patterns can be set using the Property Editor, and aligned to any vector. 1. In the Shape Explorer, select Switch to Design Spaces.
10 2. Select the Bead Pattern tool on the Structure ribbon. 3. Select the Linear tool. 4. Select the base of the oil pan. 5. Click to set the direction of the beads. The plane should appear as shown: 6. Rerun the topography optimization with the same parameters as before:
11 7. When the run is complete, double-click on the name of the run to view the results. Note the linear alignment of the beads to the defined vector. Also note that Mode 1 is now 1167 Hz. This is better than the baseline result, but not as high as the initial optimization run.
12 8. Click the Analyze button on the Shape Explorer to analyze the generated shape. 9. When the run is complete, double-click on the name of the run to view the results.
Inspire : Topography Optimization. Updated by Sanjay Nainani
Inspire 2017.3: Topography Optimization Updated by Sanjay Nainani Import model Steps to Import: Select File Import Select the file Start.stmod Review Thickness Steps to Review: Select the parts from the
Step 1: Open the CAD model
In this exercise you will learn how to: Ground a part Create rigid groups Add joints and an angle motor Add joints and an angle motor Run both transient and statics motion analyses Apply shape controls
3D Design with 123D Design
3D Design with 123D Design Introduction: 3D Design involves thinking and creating in 3 dimensions. x, y and z axis Working with 123D Design 123D Design is a 3D design software package from Autodesk. A
Autodesk Inventor 2019 and Engineering Graphics
Autodesk Inventor 2019 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the
3 AXIS STANDARD CAD. BobCAD-CAM Version 28 Training Workbook 3 Axis Standard CAD
3 AXIS STANDARD CAD This tutorial explains how to create the CAD model for the Mill 3 Axis Standard demonstration file. The design process includes using the Shape Library and other wireframe functions
Inventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
Strategy. Using Strategy 1
Strategy Using Strategy 1 Scan Path / Strategy It is important to visualize the scan path you want for a feature before you begin taking points on your part. You want to try to place your points in a way
ANSYS AIM Tutorial Structural Analysis of a Plate with Hole
ANSYS AIM Tutorial Structural Analysis of a Plate with Hole Author(s): Sebastian Vecchi, ANSYS Created using ANSYS AIM 18.1 Problem Specification Pre-Analysis & Start Up Analytical vs. Numerical Approaches
COPYRIGHT DASSAULT SYSTEMES Version 5 Release 19 January 2009 EDU-CAT-EN-ASL-FS-V5R19
CATIA Training CATIA Aerospace Sheet Metal Design Detailed Steps COPYRIGHT DASSAULT SYSTEMES Version 5 Release 19 January 2009 EDU-CAT-EN-ASL-FS-V5R19 Table of Contents Additional Exercise: Aerostructure...3
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to
In this tutorial, you will create the model of a chair, as shown in the image below, using the extended primitives and modifiers.
Office Chair In this tutorial, you will create the model of a chair, as shown in the image below, using the extended primitives and modifiers. Creating the Project Folder Create a new project folder with
Lab Assignment #1: Introduction to Creo ME 170
Lab Assignment #1: Introduction to Creo ME 170 Instructor: Mike Philpott (email: mphilpot@illinois.edu) Date Due: One week from Start Day of Lab (turn in deadline 11pm night before next lab) Make sure
Placing Text in Columns
Chapter When entering a page of text it is sometimes advantageous to place that text in columns. This can make the passage easier to read and make more efficient use of the space available on a page. Microsoft
Solid Edge ST4 Update Training (Display)
Solid Edge ST4 Update Training (Display) Presented By: Steve Webb Topic Middle Mouse Button Rotate Model Edge Display Display Performance View Style Thread and Weld Bead Texture Page 2 Middle Mouse Button
Lesson 5: Board Design Files
5 Lesson 5: Board Design Files Learning Objectives In this lesson you will: Use the Mechanical Symbol Editor to create a mechanical board symbol Use the PCB Design Editor to create a master board design
Autodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
VISI-Progress Step-by-Step Unfolding
VISI-Progress Step-by-Step Unfolding VISI Progress - Unfolding Part Management This document has been provided to describe in detail the new unfolding routines and interfaces for VISI-Progress that have
Propeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step
Feature-based CAM software for mills, multi-tasking lathes and wire EDM. Getting Started
Feature-based CAM software for mills, multi-tasking lathes and wire EDM www.featurecam.com Getting Started FeatureCAM 2015 R3 Getting Started FeatureCAM Copyright 1995-2015 Delcam Ltd. All rights reserved.
Delta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
Lesson 17 Shell, Reorder, and Insert Mode
Lesson 17 Shell, Reorder, and Insert Mode Figure 17.1 Oil Sink OBJECTIVES Master the use of the Shell Tool Reorder features Insert a feature at a specific point in the design order Create a Hole Pattern
TRAINING GUIDE. Sample. Distribution. not for LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
1 In the Mini Window Editor, double-click phase 1 (GF-Wall-External) to make it current:
1 This Quick Start tutorial introduces you to the basics of creating an intelligent drawing using the BIM components supplied with MicroGDS 2010. Here we demonstrate how to construct the external walls
SolidWorks 2015 User Interface
SolidWorks 2015 User Interface SolidWorks a Dassault Systèmes Product Starting SolidWorks 1) On the desktop, double-click or from the start menu select: All Programs SOLIDWORKS 2015 SOLIDWORKS 2015. 2)
Design a Simple Fan in 123D Design
Design a Simple Fan in 123D Design Learn to use 123D Design to make and print this simple fan. 123D Design is a free, powerful, yet simple 3D creation and editing tool. It allows you to design and build
TRAINING GUIDE WCS-PART-1
TRAINING GUIDE WCS-PART-1 Mastercam Training Guide Objectives The learner will create the geometry for WCS-Part-1. This Lesson will cover the following topics: Create a 3-dimensional drawing by: Creating
solidthinking Design Release Notes
solidthinking Design 2017.2 Release Notes The solidthinking Design package includes Inspire and Evolve 2017.2. Inspire is available on Windows, while Evolve is available on Windows and Mac. solidthinking
This is the opening view of blender.
This is the opening view of blender. Note that interacting with Blender is a little different from other programs that you may be used to. For example, left clicking won t select objects on the scene,
Creating a 2D Geometry Model
Creating a 2D Geometry Model This section describes how to build a 2D cross section of a heat sink and introduces 2D geometry operations in COMSOL. At this time, you do not model the physics that describe
Tutorial 1 Engraved Brass Plate R
Getting Started With Tutorial 1 Engraved Brass Plate R4-090123 Table of Contents What is V-Carving?... 2 What the software allows you to do... 3 What file formats can be used?... 3 Getting Help... 3 Overview
This tutorial will take you all the steps required to import files into ABAQUS from SolidWorks
ENGN 1750: Advanced Mechanics of Solids ABAQUS CAD INTERFACE TUTORIAL School of Engineering Brown University This tutorial will take you all the steps required to import files into ABAQUS from SolidWorks
ME Week 3 Project 3 - Plastic Part Thicken Method
Plastic Part Commands The following section will give a further overview of the Autodesk Inventor plastic part commands. 1. Project 3 This project will further introduce you to the Autodesk Inventor 2012
General 3D joint. 1 New project
General 3D joint Welcome to IDEA StatiCa tutorial. We will show how to use software IDEA StatiCa 8 to model, design and check a structural steel joint, example being a general 3D joint. 1 New project Let
RhinoCAM-NEST 2018 Quick Start Guide MecSoft Corporation
2 Table of Contents About RhinoCAM-NEST 3 Using this Guide 4 Useful Tips 5 About RhinoCAM-NEST 6 1 Running... RhinoCAM 6 2 About... the RhinoCAM Display 6 3 Launching... the NEST Module 7 Rectangular Nesting
Analysis Run Exercise
Analysis Run Exercise In this exercise you will setup and run an analysis on the original design and the optimized design to compare the results. The exercise follows very closely the video in the See
ANSYS AIM Tutorial Stepped Shaft in Axial Tension
ANSYS AIM Tutorial Stepped Shaft in Axial Tension Author(s): Sebastian Vecchi, ANSYS Created using ANSYS AIM 18.1 Contents: Problem Specification 3 Learning Goals 4 Pre-Analysis & Start Up 5 Calculation
REVIT ARCHITECTURE 2016
Page 1 of 6 REVIT ARCHITECTURE 2016 Revit Architecture 2016: CREATE A CHAMFERED COLUMN COMPONENT About creating a chamfered column family typical to the Victorian cottage style. Add the column to your
Tutorial Second Level
AutoCAD 2018 Tutorial Second Level 3D Modeling Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
Chapter 4 Feature Design Tree
4-1 Chapter 4 Feature Design Tree Understand Feature Interactions Use the FeatureManager Design Tree Modify and Update Feature Dimensions Perform History-Based Part Modifications Change the Names of Created
Skateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
TRAINING SESSION Q2 2016
There are 8 main topics in this training session which focus on the Sketch tools in IRONCAD. Content Sketch... 2 3D Scene Background Settings... 3 Creating a new empty Sketch... 4 Foam with cut out for
Lateral Loading of Suction Pile in 3D
Lateral Loading of Suction Pile in 3D Buoy Chain Sea Bed Suction Pile Integrated Solver Optimized for the next generation 64-bit platform Finite Element Solutions for Geotechnical Engineering 00 Overview
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
Types of Idealizations. Idealizations. Cylindrical Shaped Part. Cyclic Symmetry. 3D Shell Model. Axisymmetric
Types of Idealizations Idealizations Selecting the model type 3D Solid Plane Stress Plane Strain 3D Shell Beam Cyclic Symmetry Cylindrical Shaped Part Interior Pressure Load 3D model can be used to model
Introduction: RS 3 Tutorial 1 Quick Start
Introduction: RS 3 Tutorial 1 Quick Start Welcome to RS 3. This tutorial introduces some basic features of RS 3. The model analyzes the effect of tank loading on an existing sloped underground tunnel.
Exercise Guide. Published: August MecSoft Corpotation
VisualCAD Exercise Guide Published: August 2018 MecSoft Corpotation Copyright 1998-2018 VisualCAD 2018 Exercise Guide by Mecsoft Corporation User Notes: Contents 2 Table of Contents About this Guide 4
TABLE OF CONTENTS INTRODUCTION... 2 OPENING SCREEN BEGIN ANALYSIS... 4 Start a New File or Open a Previously Saved File... 4
3D-BLAST August 2010 TABLE OF CONTENTS INTRODUCTION... 2 OPENING SCREEN... 3 BEGIN ANALYSIS... 4 Start a New File or Open a Previously Saved File... 4 PROGRAM TOOLBAR... 5 NAVIGATING IN THE PROGRAM...
create 2 new grid lines
STEP 1: open your class-01 Project file _ go to Level 1 _ select grid line 1 _ type CO (copy) _ repeat for grid line 3 as shown in image 1 Architectural Column STEP 2: from the Ribbon under the Home tab
Tips and tricks. AutoCAD 2010
Tips and tricks AutoCAD 2010 Parametric Drawing Powerful new parametric drawing functionality in AutoCAD 2010 enables you to dramatically increase productivity by constraining drawing objects based on
Creating T-Spline Forms
1 / 28 Goals 1. Create a T-Spline Primitive Form 2. Create a T-Spline Revolve Form 3. Create a T-Spline Sweep Form 4. Create a T-Spline Loft Form 2 / 28 Instructions Step 1: Go to the Sculpt workspace
TerraScan Tool Guide
TerraScan Main Toolbox General Toolbar Draw Toolbar Groups Toolbar Vectorize Towers Toolbar Road Toolbar Buildings Toolbar Building Edges Toolbar View Laser Toolbar Model Toolbar Vectorize Wires Toolbar
CO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
TRAINING GUIDE. Sample not. for Distribution LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF
TRAINING GUIDE LATHE-LESSON-1 FACE, ROUGH, FINISH AND CUTOFF Mastercam Training Guide Objectives You will create the geometry for Lathe-Lesson-1, and then generate a toolpath to machine the part on a CNC
ECE 480: Design Team #9 Application Note Designing Box with AutoCAD
ECE 480: Design Team #9 Application Note Designing Box with AutoCAD By: Radhika Somayya Due Date: Friday, March 28, 2014 1 S o m a y y a Table of Contents Executive Summary... 3 Keywords... 3 Introduction...
Revit Architecture 2016 Parametric Families
Page 1 of 6 Revit Architecture 2016 Parametric Families Revit Architecture 2016: Create a Railing Post and a Railing Type This White Paper follows on from my previous White paper for October where we created
SOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
CNC Programming Simplified. EZ-Turn / TurnMill Tutorial.
CNC Programming Simplified EZ-Turn / TurnMill Tutorial www.ezcam.com Copyright Notice This manual describes software that contains published and unpublished works of authorship proprietary to EZCAM Solutions,
This document shows you how to set the parameters for the ModuleWorks Material Removal Simulation.
Table of Contents Introduction:... 3 Select Profile:... 4 Tool Table - Create Tool(s)... 5 Tool properties:... 5 Tool Color R/G/B:... 6 Simulation Configurations - create stock... 7 What if plugin is greyed
SIEMENS. Modeling assemblies. Self-Paced Training. spse01540
SIEMENS Modeling assemblies Self-Paced Training spse01540 Proprietary and restricted rights notice This software and related documentation are proprietary to Siemens Product Lifecycle Management Software
Autodesk Fusion 360: Model. Overview. Modeling techniques in Fusion 360
Overview Modeling techniques in Fusion 360 Modeling in Fusion 360 is quite a different experience from how you would model in conventional history-based CAD software. Some users have expressed that it
1.1: Introduction to Fusion 360
.: Introduction to Fusion 360 Fusion 360 is a cloud- based CAD/CAM tool for collaborative product development. The tools in Fusion enable exploration and iteration on product ideas and collaboration within
F1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
Solid Problem Ten. In this chapter, you will learn the following to World Class standards:
C h a p t e r 11 Solid Problem Ten In this chapter, you will learn the following to World Class standards: 1. Sketch of Solid Problem Ten 2. Starting a 3D Part Drawing 3. Modifying How the UCS Icon is
Introduction to Solid Modeling
Introduction to Solid Modeling Parametric Modeling 1 Why draw 3D Models? 3D models are easier to interpret. 3D models can be used to perform engineering analysis, finite element analysis (stress, deflection,
New Capabilities in Project Hydra for Autodesk Simulation Mechanical
New Capabilities in Project Hydra for Autodesk Simulation Mechanical Sualp Ozel, PE. Autodesk SM2447-L In this hands-on lab, we will go through several exercises and cover several new capabilities included
Doctor Walt s Solid Edge Version 19 Workbook 137
Still using the SMART DIMENSION Tool, click on the left vertical edge of the sketch. Move the cursor to the left and click to set the text position. Type 1.5 for the value and hit the ENTER Key. Next,
Lesson 1: Creating T- Spline Forms. In Samples section of your Data Panel, browse to: Fusion 101 Training > 03 Sculpt > 03_Sculpting_Introduction.
3.1: Sculpting Sculpting in Fusion 360 allows for the intuitive freeform creation of organic solid bodies and surfaces by leveraging the T- Splines technology. In the Sculpt Workspace, you can rapidly
Finite Element Course ANSYS Mechanical Tutorial Tutorial 4 Plate With a Hole
Problem Specification Finite Element Course ANSYS Mechanical Tutorial Tutorial 4 Plate With a Hole Consider the classic example of a circular hole in a rectangular plate of constant thickness. The plate
Tips & Techniques in Autodesk Inventor 2013/2014 PLTW - Wisconsin Dec. 10, 2013
Tips & Techniques in Autodesk Inventor 2013/2014 PLTW - Wisconsin Dec. 10, 2013 Dan Banach Autodesk Inc. Dataset https://www.dropbox.com/sh/scpc4lkk94lmq8n/ydbxbxemet Instructors & students register for
Quick Start Guide. for VisualNEST Published: December MecSoft Corpotation
Quick Start Guide for VisualNEST 2019 Published: December 2018 MecSoft Corpotation Copyright 1998-2018 VisualNEST 2019 Quick Start Guide by MecSoft Corporation User Notes: Contents 2 Table of Contents
The ProtoTRAK Parasolid Converter Operating Manual
The ProtoTRAK Parasolid Converter Operating Manual Document: P/N 28070 Version: 042216 Parasolid for Mills Compatible with offline and SMX ProtoTRAK Control models Southwestern Industries, Inc. 2615 Homestead
SOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
Appendix C: STEM Course Outline
C Appendix C: STEM Course Outline Science, Technology, Engineering, and Mathematics (STEM) Course Outline 1 Lesson 1: Using the Interface Engineering: Knowledge of an engineering design industry software
AutoCAD 2013 Tutorial - Second Level: 3D Modeling
AutoCAD 2013 Tutorial - Second Level: 3D Modeling Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites to
Structural re-design of engine components
Structural re-design of engine components Product design cycle Design Development Testing Structural optimization Product knowledge Design freedom 2/18 Structural re-design of engine components Product
ME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
TRAINING SESSION Q3 2016
There are 6 main topics in this training session which is focusing on 3D Import and 2D Drawing Tips and Tricks in IRONCAD. Content 3D modeling kernels... 2 3D Import... 3 Direct Face Modeling... 5 Unfold
TUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
Autodesk Inventor 2016
Parametric Modeling with Autodesk Inventor 2016 Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn
CADCAM using Powermill
CADCAM using Powermill In this exercise you will create the toolpaths necessary to machine the Cowling model. Create a folder on your h: called Powermill. Inside this create a folder called cowling2009.
In this exercise, you will convert labels into geodatabase annotation so you can edit the text features.
Instructions: Use the provided data stored in a USB. For the report: 1. Start a new word document. 2. Follow an exercise step as given below. 3. Describe what you did in that step in the word document
Figure 1: NC > 2 Axis menu > Options
Click To See: How to Use Online Documents SURFCAM Online Documents J 685)&$0Ã5HIHUHQFHÃ0DQXDO 7 &21),*85$7,21722/6 7.1 INTRODUCTION SURFCAM s default configuration parameters are contained in the SURFCAM.INI
Basic MicroStation Training Outline
12:30 DAY 1 Equipment Review Workstation, monitor, keyboard File server, Plot server, STATE server Drive Assignments Shortcut Menu General overview of commands Explorer Managing Folders & Files MicroStation
Introduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
Oasys Pdisp. Copyright Oasys 2013
Oasys Pdisp Copyright Oasys 2013 All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping,
Motion Guide Animations
Motion Guide Animations Chapter 8 Animations that involve objects orbiting around a point can be done using fixed points, but better results can sometimes be achieved through the use of a circular motion
Creating a Special PowerPoint Title Slide Using WordArt
Creating a Special PowerPoint Title Slide Using WordArt 1. Open a new slideshow and delete the topic and content textboxes 2. Click on the Insert tab and click on the WordArt tool icon. (Suggestion: start
Battery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
Getting Started with Mastercam Solids. March 2016
Getting Started with Mastercam Solids March 2016 Mastercam 2017 Solids Getting Started TERMS OF USE Date: March 2016 Copyright 2016 CNC Software, Inc. All rights reserved. Software: Mastercam 2017 Use
SimLab 14.2 Release Notes
SimLab 14.2 Release Notes Highlights SimLab 14.2 comes with various changes that improve performance and graphics rendering. In addition to java scripting, python scripting is introduced. The enhancements,
Fuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
SolidWorks Implementation Guides. User Interface
SolidWorks Implementation Guides User Interface Since most 2D CAD and SolidWorks are applications in the Microsoft Windows environment, tool buttons, toolbars, and the general appearance of the windows
Lesson 1 Parametric Modeling Fundamentals
1-1 Lesson 1 Parametric Modeling Fundamentals Create Simple Parametric Models. Understand the Basic Parametric Modeling Process. Create and Profile Rough Sketches. Understand the "Shape before size" approach.
1. In the first step, the polylines are created which represent the geometry that has to be cut:
QCAD/CAM Tutorial Caution should be exercised when working with hazardous machinery. Simulation is no substitute for the careful verification of the accuracy and safety of your CNC programs. QCAD/CAM or
Adjust model for 3D Printing. Direct modeling tools 13,0600,1489,1616(SP6)
Adjust model for 3D Printing Direct modeling tools 13,0600,1489,1616(SP6) Sometimes, the model needs to be prepared or adapted for printing. Adding material, change of a draft angles are an example. In
CADMATIC is a registered trademark of CADMATIC Oy. All other trademarks are the property of their respective owners.
Diagram Outfitting & Plant Design Hull Information Management: eshare, ebrowser, ego Release highlights 2018T2 Version 2018T2 includes many additions that increase the productivity of work in 3D and the
Saphir NL (PTA) Tutorial #1
Saphir NL (PTA) Tutorial #1 1. Introduction This tutorial provides a description of the options and workflow in KAPPA-Workstation. This includes creation of new documents and analyses, loading of pressure
Mechanical Design V5R19 Update
CATIA V5 Training Foils Mechanical Design V5R19 Update Version 5 Release 19 August 2008 EDU_CAT_EN_MD2_UF_V5R19 1 About this course Objectives of the course Upon completion of this course you will be able
TUTORIAL 7: Stress Concentrations and Elastic-Plastic (Yielding) Material Behavior Initial Project Space Setup Static Structural ANSYS ZX Plane
TUTORIAL 7: Stress Concentrations and Elastic-Plastic (Yielding) Material Behavior In this tutorial you will learn how to recognize and deal with a common modeling issues involving stress concentrations
Piping Design. Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index
Piping Design Site Map Preface Getting Started Basic Tasks Advanced Tasks Customizing Workbench Description Index Dassault Systèmes 1994-2001. All rights reserved. Site Map Piping Design member member