Installing the EPSON TM-T88IV Receipt Restick Printer in Windows using an Ethernet Connection

Transcription

1 One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY PC-AMERICA, (Voice) (Fax) Installing the EPSON TM-T88IV Receipt Restick Printer in Windows using an Ethernet Connection This is a step by step guide for installing the Epson TM-T88IV Receipt Restick Printer in a Windows 32 or 64 bit environment and configuration for use with CRE/RPE. 1 P a g e

2 Using a CAT-5 network cable (RJ45 connector) through a router or switch this option requires the purchase of a router or switch and network cable. Before you begin, make sure your EPSON TM- T88IV printer is plugged in and properly connected to your router/switch via network cable and that the paper roll is properly seated. The other end of the cable should be connected to the corresponding port on the back of your receipt printer (see image below). 2 P a g e

3 Configuring the Ethernet properties for the Epson printer Please download the Epson utility from the following link: 1. Locate the zip file you downloaded Epson_Utility_for_Ethernet_Printers.zip and extract its contents to a convenient location. Right click on the extracted file Wcfg300a.exe and select Run as administrator (XP users, simply double-click on the extracted file). Follow the on screen instructions to install the Epson TMNet WinConfig Version Select Next. 2. Select I accept the terms of the license agreement. Select Next. 3 P a g e

4 3. Select Next. 4. Select Next. 5. Select Install. 4 P a g e

5 6. Select Finish. Select Start, point to Programs, point to EPSON TMNet WinConfig, then select TMNet WinConfig Ver3.00 to start the configuration utility. 1. Select Ethernet. 2. Select the printer detected by the application that you want to assign an IP address to. 3. Select Configuration. 5 P a g e

6 1 Select the TCP/IP tab. 2 Select Manual for IP Address Setting. 3 Select Set using PING. 4 Assign the IP address, the Subnet mask, and the Default gateway. Ask your administrator for the IP address and the Default gateway to be set.( In our example we are using an IP Address of , Subnet Mask of , and Default Gateway of ) 5 Select OK. 6 Select Yes. 7 Enter the password set in the print server, then select OK. If you have never set a password, select OK without entering a password. 6 P a g e

7 8 Select OK. 9 Select OK. Note: If the printer is not detected you can access the firmware of the printer by opening your internet browser and entering the following default address: Before you begin, make sure your EPSON printer is plugged in, and that the receipt paper roll is properly seated. 7 P a g e

8 Make sure the printer is turned off for the driver installation. Before you begin please download and extract the installation files from: Locate the zip file you downloaded APD_454aE.zip and extract its contents to a convenient location. Right click on the extracted file APD_454aE a.exe and select Run as administrator (XP users, simply double-click on the extracted file). 1. Select Next to begin the installer. 2. Select I accept the terms in the license agreement and select Next. 8 P a g e

9 3. Select Minimum (Recommended), then hit Next. 4. Select Add. 5. Under the Select driver dropdown, locate and select EPSON TM-T88IV ReStick. The Printer name should auto fill EPSON TM-T88IV ReStick. 6. Under Port type, locate and select Create an Ethernet port. 7. Hit Next. 9 P a g e

10 8. Enter the IP address configured in step 4 of page 6. (In our example, we assigned the printer an IP address of ) 9. Select Next. 10. Select Next. 11. Select Next. 10 P a g e

11 12. Hit Finish. 11 P a g e

12 At the Windows Desktop, you re ready to set up the properties for your printer. You can now turn the printer on. Select Start, Control Panel, then View devices and printers. Right-click on the printer that was just installed and select Printing preferences. 12 P a g e

13 1. Select the Document Settings tab. 2. Select PaperSource: <Document[NoFeed,NoCut]>. 3. Select Document[NoFeed,NoCut]. 4. Select Apply, then OK. 13 P a g e

14 Configuring the printer in RPE/CRE. 1. Start the RPE/CRE program. 2. Select the Options/Manager and enter your password (where applicable) select [4] Setup [L] Friendly Printer Setup and re-enter your password if necessary. 3. Select/Highlight Receipt under Select Friendly Printer. 4. Select/Highlight Epson TM-T88IV ReStick under Select Local Windows Printer. 5. Under the Printer Type dropdown, select Epson Thermal Receipt Printer. 6. Make sure Cut receipt at this station is checked. 7. Hit Save & Exit to keep your changes. 14 P a g e