Data Logging Guide RIVA/Vi-PEC V88R ECU

Transcription

1 Data Logging Guide RIVA/Vi-PEC V88R ECU PART# - RS11890-ECU-DC APPLICATION(S): Sea-Doo 260/255/215hp icontrol Models RIVA/Vi-PEC ECU Manager Web Site: Table of Contents 1. Data Log Storage 2. How to View Data Log Storage Status 3. How to Download Data Logs 4. How to Delete Data Logs 5. How to Display Data Logs Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 1

2 1. Data Log Storage The following reference table shows approximate amount of time ECU will log data based on the selected logging rate. Logging Rate (Hz) Time (HH:MM:SS) 1 11:22:30 2 5:41:15 5 2:16: :08: :34: :27: :13:39 A Data Log file is created every time the engine is started. The amount of data that can be stored on your RIVA/Vi-PEC ECU is dependant upon two (2) factors. The number of individual files (a maximum of 10 individual files). OR The amount of time (see chart above). Here are two examples of how Data Logging will stop: Example #1 If you start and stop the engine ten (10) times Data Logging will stop. Example #2 If you are logging data at a rate of 20Hz Data Logging will stop after 34minutes:07seconds of riding time. Once the maximum number of files or time is reached Data Logging will stop. To resume Data Loging you must delete the Data Log files stored in the RIVA/Vi-PEC ECU. Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 2

3 2. How to View Data Log Storage Status 2.1 Connect supplied communication cable to ECU connector 'MAIN'. NOTE: Communication cable is keyed and will only connect to ECU s USB connector one way and should not be forced. Connect opposite end of cable to USB port on the PC. MAIN USB Communication Port on ECU (no color band) EXP 2 (Pink Band) EXP 1 (Yellow Band) 2.2 Power up ECU by connecting lanyard. 2.3 Open Vi-PEC Calibration Software on your PC. Press the F3 Key on the keyboard. Calibration Software should now be connected to the ECU. In the upper right hand corner of the screen ONLINE should be visible. If OFFLINE is displayed no connection is active. Repeat this step again. Vi-PEC Calibration Software ONLINE/OFFLINE Status Indicator Location NOTE: A fault code may or may not be displayed at start up. If a fault code is displayed continue to next step. The fault code will be cleared in a later section of the Quick Start Guide. Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 3

4 2.4 Press 'F12' to open the 'ECU Runtime Values'. ECU Logging Status will be highlighted in red when it reaches maximum capacity. ECU Status Tab ECU Logging Status ECU Logging Capacity 3. How to Download Data Logs 3.1 With the ECU connected to your computer open the Vi-PEC Calibration Software and 'Online'. In the ECU Controls menu select ECU Log File Download. ECU Controls ECU Log File Download Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 4

5 3.2 In the ECU Log File Manager (Figure A), select the log file you wish to save. With the correct log file highlighted left click Save Log As. A new window will open to allow you to give the file a name and select where to save it (Figure B). Select Save to save a copy. The default directory is C:\ViPEC\VTS. NOTE: Larger the data files will take longer to save. Figure A Selected Data Log Save Selected Log File Figure B Directory being saved to File Name Save NOTE: Data Log files are saved as filename.llg. These files can be ed for support or help with any issues. Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 5

6 4. How to Delete Data Logs 4.1 Before proceeding download and save all Data Log Files (see section 1 above). Once deleted the files cannot be retrieved. 4.2 In the ECU Log File Manager click on the Delete All Logs button at the bottom of the window. This is permanent. Data Log Files deleted cannot be retrieved. Example 1 Maximum number of Data Logs (10) Delete All Logs Will delete all files without saving them. 5. How to Display Data Logs 5.1 In the Display Mode menu select Log Analysis'. Note: while reviewing datalogs the ECU does not need to be connected. Display Mode Log Analysis Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 6

7 5.2 A new view will be displayed showing the displayed log (Figure A). To activate the cursor left click with the mouse on the data. A vertical bar will be shown displaying the current value at the selected location (Figure B). Use the 'UP' or 'DOWN' arrow keys to zoom in or out on the cursors position. Figure A Figure B Proceed to next page. Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 7

8 5.3 To return to the ECU view. In the Display Mode menu select ECU'. Display Mode ECU For more detailed information about Data Logging please refer to the Help menu in the Vi-PEC Engine Management program. Word doc. RIVA/Vi-PEC V88R Sea-Doo Data Log Guide H1 8/12/13 8