Parameter Value Unit. Contact Discharge Voltage Per IEC KV. Air Discharge Voltage Per IEC KV. Operating Temperature -55 to +125
|
|
- Silvester Norris
- 5 years ago
- Views:
Transcription
1 1 Feature Ultra-Low capacitance:0.05pf(typ.) Fast response time(<1ns) Low leakage current(<10na) IEC (Contact): 8KV IEC (Air) :15KV Bi-directional, single line protection 3 Application HDTV/Smart TV Set-Top Box Laptop/Desktop Computer HDMI USB 3.0 USB3.1 Lightning Thunderbolt 5 Pin Description 2 Description The polymer ESD suppressor provide ESD protection for high-speed interfaces. This protection is a result of its ultralow capacitance (0.05pF) that is well suited for HDMI1.3/1.4 USB3.0 USB3.1 ESD protection applications, and it can be used to meet the ESD immunity requirements of IEC (15KV air, 8KV contact discharge) Caution: This component is designed for signal line protection only, not intended to be used on power lines or for power bus applications. 4 Device Information Single-Channel ESD Protection Diode in 0402 Package Model Package Size mm 0.52 mm 0.38 mm 6 General Characteristics Parameter Value Unit Contact Discharge Voltage Per IEC KV Air Discharge Voltage Per IEC KV Operating Temperature -55 to +125 Storage Temperature -40 to Electrical Characteristics(TA =25 C) Parameter Symbol Conditions Min. Typ. Max. Units Continuous Operating Voltage V DC V Trigger Voltage V T IEC KV contact discharge V Clamping Voltage V C IEC KV contact discharge V Leakage Current I L DC 5V shall be applied on component na Capacitance C P Measured at 10MHz pf ESD Pulse Withstand Pulses IEC KV contact discharge Notes: 1.Trigger and clamping voltage are measured per IEC , 8KV contact discharge method. 2.After reliability tests such as high Temp storage, Temp cycles, continuous ESD strike etc, the maximum leakage current is less than 1uAmaximum leakage current is less than 1uA. Rev : /7
2 8 Typical ESD Response(IEC , 8KV contact discharge) 9 Typical ESD Response(IEC , 8KV contact discharge) Voltage ( V ) Time(ns) 10 Typical Device Capacitance VS. Frequency Capacitance(pF) E E E E+10 Frequency(Hz) Rev : /7
3 11 Eye Diagram Measurement HDMI Mask at 3.4 Gbps USB3.0 Mask at 5.0 Gbps 12 ESD Protection for HDMI HDMI Port HDMI Chipset D2+ D2- D1+ D1- D0+ D0- CLK+ CLK- Rev : /7
4 13 Soldering Parameters Profile Feature Pre Heat Temperature Min (Tsmin) Temperature Max (Tsmax) Time (ts) from (Tsmin to Tsmax) Ramp-up Rate (TL to Tp) Liquidus temperature (TL) Time (tl) maintained above TL Pb-Free Assembly 150 C 200 C seconds 3 C/second max. 217 C seconds Peak package body temperature (Tp) /-5 C Time (tp)* within 5 C of the specified classification temperature (Tc) Ramp-down Rate (Tp to TL) Time 25 C to peak temperature 30* seconds 6 C/second max. 8 minutes max. * Tolerance for peak profile temperature (Tp) is defined as a supplier minimum and a user maximum. Rev : /7
5 14 Package Dimension W L R Recommended Solder Pad Footprint H P 0.90 *Sizes in mm Notes: This solder pad layout is for reference purposes only. Unit: Millimeters Dimension Min. Typ. Max. L W P H R Rev : /7
6 15 Taping Specification Unit: Millimeters A0 B0 W F E P1 P2 P0 D0 T 0.68± ± ± ± ± ± ± ± ± ±0.03 Reel Dimension Unit: Millimeters W2 W1 C N A A N Min. C W2 Max. W1 Min. W1 Max ± ± Rev : /7
7 16 Ordering & Contact Information Ordering Code Package Net Weight Delivery Form Delivery Quantity mg / 1 pce Mini T&R (7 ) 10,000 pcs/reel Shanghai Leiditech Electronic Co.,Ltd sale1@leiditech.com Tel : Fax : Rev : /7
PESD0402MS05 Surface Mount Polymeric ESD Suppressor
\ Description polymeric ESD suppressor help protect sensitive electronic equipment against electrostatic discharge (ESD) without distorting data signals. This protection is a result of its ultra-low capacitance
More informationMLSEP*** Series. Multilayer Polymer ESD Suppressor. Features. Application. Electrical Characteristics
Features ESD protection for high speed data lines to IEC61000-4-2 ESD contact discharge typical 8KV, max 15KV IEC61000-4-2 ESD air discharge typical 15KV, max 25KV Protect four data lines Flow through
More informationTVL AB0 Product Engineering Specification
1. Scope TVL 0201 01 A0 Product TVL 0201 01 A0 is a TVS diode designed to protect one power/control line or one low speed signal line from overvoltage hazard of Electrostatic Discharge (ESD). These interfaces
More informationINPAQ. Specification TVN AB0. Product Name Transient Voltage Suppressor Series TVS Series Part No TVN AB0 Size EIA 0201
TVN 0201 01 AB0 Specification Product Name Transient Voltage Suppressor Series TVS Series Part No TVN 020101 AB0 Size EIA 0201 TVN 0201 01 AB0 Engineering Specification 1. Scope TVN 0201 01 AB0 is a TVS
More informationTVH AB1 Engineering Specification
TVH 0402 01 A1 Engineering 1. Scope GENERAL DESCRIPTION TVH 0402 01 A1 is a silicon base in ultra small SMD special packages. It is designed to protect sensitive electronics from damage or latch up due
More informationSPECIFICATION FOR APPROVAL INDEX
SPECIFICATION FOR APPROVAL INDEX COVER PAGE INDEX. 0 SCOPE...1 EXPLANATION OF PART NUMBER.1 CIRCUIT DIAGRAM & DIMENSION.....1 SPECIFICATIONS..2 TAPING PACKAGE AND LABEL MARKING...3-4 PRECAUTIONS FOR HANDLING...5-7
More informationWPE0541P1 1-Line Bi-directional Low Capacitance TVS Diode
Description Mechanical Characteristics The is designed to protect voltage sensitive components from ESD and transient voltage events. Excellent clamping capability, low leakage, and fast response time,
More informationSP1124T Discrete Unidirectional TVS Diode
SP1124T Discrete Unidirectional TVS Diode RoHS Pb GREEN Description This TVS diode is fabricated in a proprietary silicon avalanche technology and is used for high level protection of electronic equipment
More informationAQ1003 Series - 30pF 30kV Unidirectional Discrete TVS
General Purpose ESD Protection - SP003 AQ003 Series AQ003 Series - 30pF 30kV Unidirectional Discrete TVS RoHS Pb GREEN Description This diode is fabricated in a proprietary silicon avalanche technology
More informationINPAQ Global RF/Component Solutions
TVN 0201 01 SP0 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVN 0201 01 SP0 Size EIA 0201 TVN 0201 01 SP0 Engineering Specification 1. Scope TVN 0201 01 SP0 is a TVS
More informationAQ4020 Series 2.5pF, 30A Discrete TVS Diode
TVS Diode Arrays (SPA Diodes) Lightning Surge Protection- AQ4020 SP4020 Series AQ4020 Series 2.5pF, 30A Discrete TVS Diode RoHS Pb GREEN Description The AQ4020 components integrate low capacitance steering
More informationTVS Diode Arrays (SPA Diodes) SP1005 Series 30pF 30kV Bidirectional Discrete TVS. General Purpose ESD Protection - SP1005 Series Flipchip SOD882
SP1005 Series 30pF 30kV Bidirectional Discrete TVS RoHS Pb GREEN Description The SP1005 includes back-to-back Zener diodes fabricated in a proprietary silicon avalanche technology to provide protection
More informationESD9X5VL ESD9X5VL. X x. Transient Voltage Suppressor
Ultra Small Profile, low capacitance Transient Voltage Suppressor Descriptions The is an ESD transient voltage suppression component which provides a very high level of protection for sensitive electronic
More informationElectrostatic Discharged Protection Devices (ESD) Data Sheet
Electrostatic Discharged Protection Devices (ESD) Data Sheet Description is surge rated diode arrays designed to protect high speed data interfaces. It has been specifically designed to protect sensitive
More informationLow Capacitance ESD Protection - SP3002 Series. Description. Features I/O 4 I/O 3. Applications
SP3002 Series 0.85pF Diode Array RoHS Pb GREEN Description The SP3002 has ultra low capacitance rail-to-rail diodes with an additional zener diode fabricated in a proprietary silicon avalanche technology
More informationSPECIFICATION Brightek (Europe) Limited Semiconductor T01 Device. 1. Part Number Identification T A
1. Part Number Identification T01-0402 - 050-100 A - 11 Series Name Size Case : 0402 (DFP1006) 11 Bidirectional Inner code Reverse Working Voltage 050=5*10 0 =5V Parasitic Capacitance 100=10*10 0 =10pF
More informationProduct Engineering Specification TVH SP0
Part : TVH020101SP0 Version : A1 Page : 1 / 9 SCOPE Product Engineering Specification TVH 0201 01 SP0 TVH 0201 01 SP0 is a TVS diode designed to protect one power/control line or one signal line from overvoltage
More informationSP1050 Series for Power-over-Ethernet PSE Protection
SP1050 Series for Power-over-Ethernet PSE Protection RoHS Pb GREEN Description The SP1050-04BTG provides over-voltage protection for Power-over-Ethernet PSE equipment in a space saving SOIC-8 package.
More informationINPAQ Global RF/Component Solutions
TEA10402V15A0 Specification Product Name Series Part No ESD Guard TM TEA Series (Thin Film Air Gap) TEA10402V15A0 Size EIA 0402 TEA10402V15A0 Engineering Specification 1. Scope This specification is applied
More informationDATA SHEET ELECTROSTATIC DISCHARGE PROTECTION DEVICES INDUSTRIAL / CONSUMER UDD32CXXL01 series
Product specification November 05, 2018 V.0 DATA SHEET ELECTROSTATIC DISCHARGE PROTECTION DEVICES INDUSTRIAL / CONSUMER series RoHS compliant & Halogen free 2 Electrostatic Discharged Protection Devices
More informationTVU1240R1A Engineering Specification
Part : TVU1240R1A Version : A6 Page : 1 / 10 SCOPE TVU1240R1A Engineering Specification This specification is applied to protect sensitive electronic circuits from the threat of electrostatic discharge
More informationSP11xx Series Discrete Unidirectional TVS Diode
SP11xx Series Discrete Unidirectional TVS Diode RoHS Pb GREEN Description Zener diodes fabricated in a proprietary silicon avalanche technology protect each I/O pin to provide a high level of protection
More informationPRODUCT SPECIFICATION
PRODUCT SPECIFICATION DESCRIPTION DRAWN Y DESIGNED Y CHECKED Y APPROVED Y TVL 0201 01 SP0 Sandy Aaron Aaron YuChiaChang TVL 0201 01 SP0 Engineering 1. Scope TVL 0201 01 SP0 is a TVS diode designed to protect
More informationTVS Diode Arrays (SPA Diodes)
SP1005 Series 30pF 30kV Bidirectional Discrete TVS RoHS Pb GREEN Description The SP1005 includes back-to-back Zener diodes fabricated in a proprietary silicon avalanche technology to provide protection
More informationSP pF 30kV Bidirectional Discrete TVS
SP1326 15pF 30kV Bidirectional Discrete TVS RoHS Pb GREEN Description The SP1326 back-to-back diodes are fabricated in a proprietary silicon avalanche technology. These diodes provide a high ESD (electrostatic
More informationSP4050 Series. TVS Diode Arrays (SPA Diodes) Lightning Surge Protection - SP4050 Series. RoHS Pb GREEN. Description
SP4050 Series RoHS Pb GRN Description The SP4050 integrates low capacitance diodes with an additional zener diode to protect each I/O pin against SD and high surge events. This robust component can safely
More informationSP pF SOT23-6L 4 Channels Diode Array
SP319.3pF SOT23-6L 4 Channels Diode Array RoHS Pb GREEN Description 4 5 6 3 2 1 SP312-3UTG Pinout *Pins 6, 7, 9, 1 are not internally connected but should be connected to the trace. 6 7 8 9 1 5 4 3 2 1
More informationElectrostatic Discharged Protection Devices (ESD) Data Sheet
Electrostatic Discharged Protection Devices (ESD) Data Sheet Description Brightking s component is surge rated diode array designed to protect high speed data line interfaces. It has been specifically
More informationTVU1240R1A Product Engineering Specification
TVU1240R1A Product Engineering Specification 1. Scope This specification is applied to protect sensitive electronic circuits from the threat of electrostatic discharge (ESD). The function meets with the
More informationCommon Mode Noise Filter. LCFE Series. Description. Features. Applications. 1210mm Size. Source Meter. LCR Meter (3GHz) Source Meter.
Description This specification covers the engineering requirements for both Common Mode Noise Filter (CMF) and ESD Protection, especially high speed differential serial interfaces, such as USB 3., USB
More informationINPAQ Global RF/Component Solutions
TVU1240R1A Specification Product Name Series Part No ESD Guard TM Array TVU Series TVU1240R1A Size EIA 1004 TVU1240R1A Product Engineering Specification 1. Scope This specification is applied to protect
More informationSP A Discrete Bidirectional TVS Diode
SP1233 2A Discrete Bidirectional TVS Diode RoHS Pb GREEN Description The SP1233 includes TVS diodes fabricated in a proprietary silicon avalanche technology to protect each I/O pin and provide a high level
More informationSP pF 8kV DFN Plastic Unidirectional Discrete TVS
SP1053 8.5pF 8kV 01005 DFN Plastic Unidirectional Discrete TVS RoHS Pb GREEN Description Avalanche breakdown diodes fabricated in a proprietary silicon avalanche technology protect each I/O pin to provide
More informationSP5001 Series 4 Channel TVS Common Mode Filter
Low Capacitance ESD Protection - SP51 Series SP51 Series 4 Channel TVS Common Mode Filter RoHS Pb GREEN Description The SP51 Series is a highly integrated Common Mode Filter (CMF providing both ESD protection
More informationAQ1026 Series 15pF 30kV Bidirectional Discrete TVS
General Purpose ESD Protection - AQ126 SP126 Series AQ126 Series 15pF 3kV Bidirectional Discrete TVS RoHS Pb GREEN Description Avalanche breakdown diodes fabricated in a proprietary silicon avalanche technology
More informationCitrusCom CS0801S. Applications. Features. Mechanical Characteristics. Description. Circuit Diagram. Pin Configuration
Features Transient protection for high-speed data lines IEC 61000-4-2 (ESD) ±15kV (Air) ±8kV (Contact) IEC 61000-4-4 (EFT) 40A (5/50 ns) Cable Discharge Event (CDE) Package optimized for high-speed lines
More informationAQ4022 Series 1.3pF, 15A Discrete TVS Diode
TVS Diode Arrays (SPA Diodes Lightning Surge Protection- SP4022 AQ4022 Series AQ4022 Series 1.3pF, 15A Discrete TVS Diode RoHS Pb GREEN Description The AQ4022 series integrates low capacitance steering
More informationSP2574NUTG 2.5V 40A Diode Array
TVS Diode Arrays (SPA Diodes 2.5V 40A Diode Array RoHS Pb GREEN Description The is a low-capacitance, TVS Diode Array designed to provide protection against ESD (electrostatic discharge, CDE (cable discharge
More informationSP8008 Series Diode Array
SP88 Series Diode Array RoHS Pb GRN Description The SP88 integrates eight channels of ultra low capacitance common mode protection for electronic equipment exposed to electrostatic discharges (SD. This
More informationAQ24CANFD 200W TVS Diode Array
AQ24CANFD 200W TVS Diode Array RoHS Pb GREEN Description The AQ24CANFD is designed to protect automotive Controller Area Network (CAN lines from damage due to electrostatic discharge (ESD, electrical fast
More informationAQxxC-01FTG Series 450W Bidirectional TVS Diode
General Purpose ESD Protection - AQxxC-1FTG Series AQxxC-1FTG Series 5W Bidirectional TVS Diode RoHS Pb GREEN Description The bidirectional AQxxC-1FTG Series is designed to replace multilayer varistors
More informationEGA10201V05A0 Product Engineering Specification
RoHS Pb EGA10201V05A0 Product Engineering 1. Scope This specification is applied to electrostatic discharge (ESD) protection. It is designed to protect the high-speed data lines against ESD transients.
More informationSD05C Series 450W Discrete Bidirectional TVS Diode
TVS Diode rrays (SP Devices) General Purpose ESD Protection - 450W Discrete Bidirectional TVS Diode RoHS Pb GREEN Description The bidirectional SD05C TVS diode is designed to replace multilayer varistors
More informationINPAQ. Specification TEA10402V15A0. Product Name. ESD Guard TM TEA Series (Thin Film Air Gap) Size EIA Global RF/Component Solutions
TEA10402V15A0 Specification Product Name Series Part No ESD Guard TM TEA Series (Thin Film Air Gap) TEA10402V15A0 Size EIA 0402 TEA10402V15A0 Engineering Specification 1. Scope TEA series is designed to
More informationINPAQ Global RF/Component Solutions
EGA10402V05B0 Specification Product Name Series Part No ESD Guard TM EGA Series EGA10402V05B0 Size EIA 0402 EGA10402V05B0 Engineering Specification 1. Scope This specification is applied to electrostatic
More informationSELC0504F Low Capacitance Tvs Diode Array DESCRIPTION FEATURES APPLICATIONS IEC COMPATIBILITY MAXIMUM RATINGS
DESCRIPTION The SELC0504F provides a typical line to line capacitance of 0.6pF and low insertion loss up to 3GHz providing greater signal integrity making it ideally suited for USB 2.0 applications,such
More informationINPAQ Global RF/Component Solutions
TEA10201V05A0 Specification Product Name Series Part No ESD Guard TM TEA Series (Thin Film Air Gap) TEA10201V05A0 Size EIA 0201 TEA10201V05A0 Engineering Specification 1. Scope This specification is applied
More informationRClamp5011ZA. Ultra Small RClamp 1-Line, 5V ESD Protection. PROTECTION PRODUCTS - RailClamp Description. Features. Mechanical Characteristics
- RailClamp Description RClamp TVS diodes are designed to protect sensitive electronics from damage or latch-up due to ESD. They are designed to replace 21 size multilayer varistors (MLVs) in portable
More informationSP2555NUTG 2.5V 45A Diode Array
SP2555NUTG 2.5V 45A Diode Array RoHS Pb GREEN Description The SP2555NUTG is a low-capacitance, TVS Diode Array designed to provide protection against ESD (electrostatic discharge), CDE (cable discharge
More informationUSB-OTG BUS-Port ESD Protection for V BUS = 12 V
USB-OTG BUS-Port ESD Protection for V BUS = 12 V 6 5 4 1 2 3 MARKING (example only) 2517 Dot = pin 1 marking XX = date code YY = type code (see table below) 7 2112 XX YY DESIGN SUPPORT TOOLS click logo
More informationSP5001 Series 4 Channel Common Mode Filter with ESD Protection
Low Capacitance ESD Protection - SP51 Series SP51 Series 4 Channel Common Mode Filter with ESD Protection RoHS Pb GREEN Description The SP51 Series is a highly integrated Common Mode Filter (CMF) providing
More informationINPAQ Global RF/Component Solutions
EGA10201V00A3 Specification Product Name Series Part No ESD Guard TM EGA Series EGA10201V00A3 Size EIA 0201 EGA10201V00A3 Engineering Specification 1. Scope This specification is applied to electrostatic
More informationMLVG0402 Series Engineering Specification
RoHS Pb MLVG0402 Series Engineering 1. Scope (1) Lead free type (2) SMD type zinc oxide based ceramic chip (3) Insulator over coat keeps excellent low and stable leakage current (4) Plating termination
More informationAOZ8312. Low Capacitance 2.5 V TVS Diode. Features. General Description. Applications
Low Capacitance 2.5 V TVS Diode General Description The is a transient voltage suppressor array designed to protect high speed data lines from ESD and lightning. This incorporates twelve low capacitance
More informationElectrostatic Discharged Protection Devices (ESD) Data Sheet
Electrostatic Discharged Protection Devices (ESD) Data Sheet Description Brightking s SET23AXXL02 series of transient voltage suppressor (TVS) are designed to protect components which are connected to
More informationAlfa-MOS Technology. AFE0563 One-Line ESD Protection Low Capacitance Bi-direction TVS. General Description. Pin Description ( DFN )
General Description are designed by bi-direction TVS diode, to protect high speed data interfaces. This product has been specifically designed to protect sensitive components which are connected to data
More information0504A PESDR0504S2. 4-Line Low Capacitance TVS Diode Array. Mechanical Characteristics. Description. Applications. Features. Marking Information
4-Line Low Capacitance TVS Diode Array Description The is a low capacitance TVS array, utilizing leading monolithic silicon technology to provide fast response time and low ESD clamping voltage, making
More informationEGA10603V12A1-B Engineering Specification
RoHS Pb EGA10603V12A1- Engineering 1. Scope This specification is applied to electrostatic discharge (ESD) protection. It is designed to protect the high-speed data lines against ESD transients. It has
More informationTVN S AB0 Engineering Specification
TVN S3 A Engineering. Scope TVN S3 A s are TVS diodes designed to protect one power/control line or one low speed signal line from overvoltage hazard of Electrostatic Discharge (ESD), Electrical Fast Transients
More informationElectrostatic Discharged Protection Devices (ESD) Data Sheet
Electrostatic Discharged Protection Devices (ESD) Data Sheet Description Brightking s SDT23CXXL02 series are designed to protect sensitive electronics from damage or latch-up due to ESD and other voltage
More informationUltra Low Capacitance Bidirectional Symmetrical (BiSy) Single Line ESD Protection Diode in LLP1006-2M
Ultra Low Capacitance Bidirectional Symmetrical (BiSy) Single Line ESD Protection Diode in LLP6-2M 1 2 21129 MARKING (example only) XY Bar = pin 1 marking X = date code Y = type code (see table below)
More informationSpecification Status: RELEASED
PAGE NO.: PAGE 1 of 6 BENEFITS Specification Status: RELEASED Industry-leading lowest capacitance; provides lowest insertion loss for high speed data signals Small size ESD protection diodes for high speed
More information0534S PESDR0534S2. 4-Line Low Capacitance TVS Diode Array. Mechanical Characteristics. Description. Applications. Features. Marking Information
4-Line Low Capacitance TVS Diode Array Description The is a low capacitance TVS arrays, utilizing leading monolithic silicon technology to provide fast response time and low ESD clamping voltage, making
More informationINPAQ Global RF/Component Solutions
TVL 0402 01 SP0 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVL 0402 01 SP0 Size EIA 0402 TVL 0402 01 SP0 Engineering Specification 1. Scope TVL 0402 01 SP0 is a TVS
More informationTVL AB1 Engineering Specification
1 Scope TVL 0402 01 A1 TVL 0402 01 A1 is a TVS diode designed to protect one power/control line or one low speed signal line from overvoltage hazard of Electrostatic Discharge (ESD). These interfaces can
More information4-Line BUS-Port ESD Protection
4-Line BUS-Port ESD Protection 2397 6 5 4 1 2 3 MARKING (example only) Dot = pin 1 marking XX = date code YY = type code (see table below) 2453 1 XX YY DESIGN SUPPORT TOOLS click logo to get started Models
More informationINPAQ Global RF/Component Solutions
TVL 0402 01 AB1 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVL 0402 01 AB1 Size EIA 0402 TVL 0402 01 AB1 Engineering Specification 1. Scope TVL 0402 01 AB1 is a TVS
More informationAZ H Transient Voltage Suppressing Device For ESD/Transient Protection. Features. Circuit Diagram / Pin Configuration. Applications.
Features ESD Protection for Line with Bi-directional. Provide ESD protection for the protected line to IEC 6000-4- (ESD) ±0kV (air), ±kv (contact) IEC 6000-4-4 (EFT) 40A (5/50ns) IEC 6000-4-5 (Lightning)
More informationSpecification Status: RELEASED
PAGE NO.: PAGE 1 of 6 Specification Status: RELEASED BENEFITS Industry-leading lowest capacitance; provides lowest insertion loss for high speed data signals Industry s smallest footprint and lowest profile
More informationRClamp3331ZA. Ultra Small RailClamp 1-Line, 3.3V ESD Protection
- RailClamp Description RailClamp TVS diodes are ultra low capacitance devices designed to protect sensitive electronics from damage or latch-up due to ESD, EFT, and EOS. They are designed for use on high
More informationElectrostatic Discharged Protection Devices (ESD) Data Sheet
Electrostatic Discharged Protection Devices (ESD) Data Sheet Description The series of is designed to protect power port and the chip Vbus interfaces. It has been specifically designed to protect sensitive
More informationPESDR0554S2. 4-Line Low Capacitance TVS Diode Array. Mechanical Characteristics. Description. Applications. Features. Ordering Information
4-Line Low Capacitance TVS Diode Array Description The is a low capacitance TVS array, utilizing leading monolithic silicon technology to provide fast response time and low ESD clamping voltage, making
More informationPLR ULTRA LOW CAPACITANCE STEERING DIODE/TVS ARRAY DESCRIPTION SC-89 PACKAGE APPLICATIONS FEATURES MECHANICAL CHARACTERISTICS PIN CONFIGURATION
ULTRA LOW CAPACITANCE STEERING DIODE/TVS ARRAY DESCRIPTION The is an ultra low capacitance (0.7pF Max. I/O to I/O) steering diode and TVS array combo. This device provides circuit protection for interfaces
More information4-Line BUS-Port ESD Protection Array - Flow Through Design
-Line BUS-Port ESD Protection Array - Flow Through Design 22736 5 MARKING Pin 1 5F = type code = date code month YY = date code year DESIGN SUPPORT TOOLS click logo to get started Models Available 1 YY
More informationAZ H Transient Voltage Suppressing Device For ESD/Transient Protection. Features. Circuit Diagram / Pin Configuration. Applications.
Features ESD Protection for 1 Line with Bi-directional. Provide ESD protection for the protected line to IEC 61000-4- (ESD) ±16kV (air), ±16kV (contact) IEC 61000-4-4 (EFT) 50A (5/50ns) IEC 61000-4-5 (Lightning)
More informationP0201V05 ULTRA LOW CAPACITANCE ESD PROTECTION COMPONENT DESCRIPTION APPLICATIONS FEATURES MECHANICAL CHARACTERISTICS PIN CONFIGURATION
ULTRA LOW CAPACITANCE ESD PROTECTION COMPONENT DESCRIPTION The is an ultra low capacitance ESD component designed to protect very high-speed data interfaces. The device has a typical capactiance of only
More informationSpecification Status: RELEASED
PAGE NO.: 1 OF 6 BENEFITS Specification Status: RELEASED Industry-leading lowest capacitance; provides lowest insertion loss for high speed data signals Small size ESD protection diodes for high speed
More informationRClamp7522T. Ultra Low Capacitance TVS Array PRELIMINARY
- RailClamp Description RailClamp TVS arrays are ultra low capacitance ESD protection devices designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive
More informationHSP051-4M10. 4-line ESD protection for high speed lines. Applications. Description. Features. Benefits. Complies with following standards
4-line ESD protection for high speed lines Datasheet production data Benefits High ESD protection level High integration Suitable for high density boards Figure 1. Functional schematic (top view) I/O 1
More informationST0561D4. 1-Line Bi-directional TVS Diode. Description. Mechanical Characteristics. Applications. Features. Ordering Information
-Line Bi-directional TVS Diode Description The ST56D4 is a bi-directional TVS diode, utilizing leading monolithic silicon technology to provide fast response time and low ESD clamping voltage, making this
More informationHSP061-4M10. 4-line ESD protection for high speed lines. Datasheet. Features. Applications. Description
Datasheet 4-line ESD protection for high speed lines Features I/O I/O 2 GND 3 I/O 3 I/O 4 2 4 µqfn-0l package Functional schematic (top view) 0 9 8 7 5 6 Product status HSP06-4M0 Internal ly not connected
More informationImpedance (Ω) at DC Resistance
Type BMB-A Series Key Features Effective EMI Protection Wide Frequency Characteristics High soldering Heat Resistance Various Package Sizes Available Suited to a Variety of Applications Terminal finish
More informationP0603V24 ULTRA LOW CAPACITANCE ESD PROTECTION COMPONENT DESCRIPTION FEATURES APPLICATIONS MECHANICAL CHARACTERISTICS PIN CONFIGURATION
ULTRA LOW CAPACITANCE ESD PROTECTION COMPONENT DESCRIPTION The is an ultra low capacitance ESD component designed to protect very high-speed data interfaces. The device has a typical capactiance of only
More information500 W, Bidirectional Low Capacitance TVS Array
Available 500 W, Bidirectional Low Capacitance TVS Array DESCRIPTION This Transient Voltage Suppressor (TVS) is assembled in a QFN-143 package which has the same pinout and footprint as the SOT-143 package.
More informationUM5204EECE. Quad Channel Low Capacitance ESD Protection Array. General Description. Rev.03 Dec /6
Quad Channel Low Capacitance ESD Protection Array TSOP-/SOT3- General Description is surge rated diode arrays designed to protect high speed data interfaces. This series has been specifically designed
More informationSpecification Status: RELEASED
PAGE NO.: 1 OF 6 Specification Status: RELEASED BENEFITS Low capacitance; provides low insertion loss for high speed data signals Small size ESD protection diodes for high speed data signals (0201 size
More informationCitrusCom CS0806U. Features. Applications. Mechanical Characteristics. Description. Circuit Diagram. Pin Configuration
Features Transient protection for high-speed data lines IEC 1000--2 (ESD) ±1kV (Air) ±8kV (Contact) IEC 1000-- (EFT) 0A (/0 ns) Cable Discharge Event (CDE) Small package (2.9mm 2.8mm 1.mm) Protects four
More informationPESDALC143T5VU Low Capacitance ESD Protector
Low Capacitance ESD Protector Description The is low capacitance transient voltage suppressor for high speed data interface that designed to protect sensitive electronics from damage or latch-up due to
More informationMLVS 0402 Series Engineering Specification
MLVS 0402 Series 1. Scope This specification is applicable to Chip Metal Oxide Varistor in multilayer technology.the customer designed part number drawing take precedence over this specification. For RoHS
More informationL30ESDL5V0C6-4X SOT23-6L. STAND-OFF VOLTAGE Volts POWER DISSIPATION WATTS ESD PROTECTION DEVICE GENERAL DESCRIPTION FEATURES APPLICATION
LITE-ON SEMICONDUCT L0ESDLV0C-X ESD PROTECTION DEVICE STANOFF VOLTAGE -.0 Volts POWER DISSIPATION - 00 WATTS GENERAL DESCRIPTION The L0ESDLV0C-X is low capacitance TVS arrays designed to protect high speed
More informationCDMSP M Surface Mount TVS Diode Array
*RoHS COMPLIANT Features RoHS compliant* Protects four I/O lines Ultra-low capacitance ~.55 pf ESD protection > kv Surge protection Applications High Definition Multimedia Interface (HDMI) Digital Visual
More informationDescription Mechanical Characteristics Features Applications Ordering Information Part Number Packaging Reel Size
ST36D4 -Line Bi-directional TVS Diode Description The ST36D4 is a bi-directional TVS diode, utilizing leading monolithic silicon technology to provide fast response time and low ESD clamping voltage, making
More informationCDDFN P - Surface Mount TVS Diode Array
*RoHS COMPLIANT Features n RoHS compliant* n Low capacitance -.4 pf (I/O to I/O) n ESD protection to IEC 61-4-2 (Level 4) Applications n HDMI 1.3, 1.4 and 2. n DisplayPort n Digital Visual Interface (DVI)
More informationL05ESDL5V0D3-2 SOT-323. STAND-OFF VOLTAGE Volts POWER DISSIPATION - 50 WATTS ESD PROTECTION DEVICE
LITE-ON SEMICONDUCTOR ESD PROTECTION DEVICE STAND-OFF VOLTAGE - 5.0 Volts POWER DISSIPATION - 50 WATTS GENERAL DESCRIPTION The is low capacitance TVS arrays designed to protect high speed data interfaces.
More informationHSP051-4M10. 4-line ESD protection for high speed lines. Datasheet. Features. Applications. Description
Datasheet 4-line ESD protection for high speed lines Features I/O 1 I/O 2 GND 3 I/O 3 I/O 4 1 2 4 µqfn-10l package Functional schematic (top view) 10 9 8 7 5 6 Internal ly not connected GND Internal ly
More informationHSP line ESD protection for high speed lines. Applications. Description. Features. µqfn 4 leads. Benefits. Complies with following standards
2-line ESD protection for high speed lines Datasheet - production data Benefits High ESD robustness of the equipment Suitable for high density boards Complies with following standards MIL-STD 883G Method
More informationRClamp7524T. Low Capacitance RClamp 4-Line ESD Protection. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics.
Low Capacitance RClamp 4-Line ESD Protection PROTECTION PRODUCTS Description RailClamp TVS arrays are ultra low capacitance ESD protection devices designed to protect high speed data interfaces. This series
More informationLow Capacitance, Single-Line ESD Protection Diode
VBUS51BD-HD1 Low Capacitance, Single-Line ESD Protection Diode 1 MARKING (example only) 856 XY Bar = cathode marking Y = type code (see table below) X = date code 111 855 DESIGN SUPPORT TOOLS click logo
More informationLow Capacitance Bidirectional Single Line TVS Protection Diode UM5080T DFN
General Description UM5080T Low Capacitance Bidirectional Single Line TVS Protection Diode UM5080T DFN2 1.0 0.6 The UM5080T TVS protection diode is designed to replace multilayer varistors (MLVs) in portable
More informationHSP051-4N10. 4-line ESD protection for high speed lines. Applications. Description. Features. Benefits. Complies with following standards
4-line ESD protection for high speed lines Datasheet production data Benefits High ESD protection level High integration Suitable for high density boards Figure 1. Functional schematic (top view) I/O 1
More information