Catalog Revised Ribbon Cable Interconnect Solutions. Ribbon Cable Interconnect Solutions

Transcription

1 Catalog Revised Ribbon Cable Interconnect Solutions onents.com Ribbon Cable Interconnect Solutions

2 Ribbon Cable Connector Selection Guide Ribbon Cable Connector Selection Guide Mates to.050" x " 2-Row Pin Header Grid Pages 10 and 11 System 50 Receptacles Pages 8-11 Mates to.50" x.50" Micro-MaTch Female Top Entry, Series, PCB Connector Page 34 Male-on-Wire Series, Page " [0.64 mm] Cable Pitch Mates to " x " 2-Row Pin Header Grid Page 15 Ultra T Bus Compliant Receptacles Pages Mates to.050" x.050" Micro-MaTch Female Side Entry, Series, PCB Connector Page 35 Male-on-Wire Series, Page 38 Solders to.075" x " 4-Row PCB Layout System 50 Paddleboard Page " [1.27 mm] Cable Pitch Mates to.050" x.050" Micro-MaTch Female Top Entry SMD, Series, PCB Connector Page 36 Male-on-Wire Series, Page 38 Solders directly to 2.54mm x 1.27mm Staggered 2 row PCB Footprint Paddle Board Connector, Series, Page " [1.27 mm] Cable Pitch (Continued).039" [1.00 mm] Cable Pitch Mates to.078" [2 mm] x.078" [2 mm] 2-Row Pin Header Grid See , Series and Part Number (Not in this Catalog) 2 mm Receptacle Connectors Pages 16 and 17 Mates to.050" x.050" Right-ngle Headers Mates to.050" x.050" Vertical Headers 50/50 Grid Receptacle Connector with or without latch 50/50 Grid Receptacle Connectors without latch 2

3 PageHead_12_HelvCdBd Ribbon Cable Connector Selection (Continued) Guide (Continued) Mates to " x " Novo Type Female Socket Connector Pages Universal I/O Pin Connectors Pages 45 and 46 Mates to " x " 3-Row Eurocard Type C & R See Catalog EUROLTCH Receptacles Page " [1.27 mm] Cable Pitch (Continued) MP-LTCH Novo Connectors Pages Mates to " x " 2-Row Universal or Low-Profile Headers Pages and 636 Series Female Socket Connectors Pages 52 and 53 " x " Footprint Mates to 2-Row DIP Sockets or Solders to PCB " x.300" Footprint.050" [1.27 mm] Cable Pitch (Continued) " x.600" Footprint 609 Series Female Socket Connectors Pages 54 and 55 Solders to.050" x " 4-Row PCB Footprint Ribbon Cable Connector Selection Guide 609 Series DIP Plugs Page and 636 Series DIP Plugs Page 57 Tyco Electronics DIP Plugs Page 58 Tyco Electronics DIP Plugs Page 59 Tyco Electronics DIP Plugs Page 60 Solder Transition Connectors Page 61 3

4 Introduction Disclaimer While Tyco Electronics Corporation and its affiliates referenced herein ( Tyco Electronics ) have made every reasonable effort to ensure the accuracy of the information in this catalog, Tyco Electronics does not guarantee that it is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information contained herein at any time without notice. Tyco Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics only obligations are those in the Tyco Electronics Standard Terms and Conditions of Sale, and in no case will Tyco Electronics be responsible for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of its products. Users should independently evaluate the suitability of, and test each product for, their application. The dimensions, specifications, designs, construction, materials and processes in this catalog are for reference purposes only and are subject to change without notice. Please consult Tyco Electronics for the most current product information. The export of certain Tyco Electronics products is restricted by the rms Export Control ct (Title 22, U.S.C. Sec 2751, et seq.) or the Export dministration ct of 1979, as amended (Title 50, U.S.C., pp et seq.). Orders may be subject to export approval by the U.S. Government. Buyer must comply with all applicable export laws of all applicable jurisdictions. 2009, 1999, 1998, 1996, 1995, 1993, 1992, 1989, 1988, 1986, 1985, 1983, 1982, 1977, 1976, 1974 and 1973 Tyco Electronics Corporation. ll Rights Reserved. MP, MPLIMITE, MPMODU, CTION PIN, MP-LTCH, MICRO-MTCH, CHMP, EUROLTCH, TE LOGO and TYCO ELECTRONICS are trademarks of the Tyco Electronics group of companies and its licensors.. Other products, logos, and company names mentioned herein may be trademarks of their respective owners. See inside back cover for Global Contacts and phone numbers. Restriction on the use of Hazardous Substances (RoHS) t Tyco Electronics, we re ready to support your RoHS requirements. We ve assessed more than 1.5 million end items/components for RoHS compliance, and issued new part numbers where any change was required to eliminate the restricted materials. Part numbers in this catalog are identified as: RoHS Compliant Part numbers in this catalog are RoHS Compliant, unless marked otherwise. These products comply with European Union Directive 2002/95/EC as amended 1 January 2006 that restricts the use of lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in certain electrical and electronic products sold into the EU as of 1 July NOTE: For purposes of this Catalog, included within the definition of RoHS Compliant are products that are clearly Out of Scope of the RoHS Directive such as hand tools and other non-electrical accessories. NOTE: Information regarding RoHS compliance is provided based on reasonable inquiry of our suppliers and represents our current actual knowledge based on the information provided by our suppliers. This information is subject to change. For latest compliance status, refer to our website referenced at right. Getting the Information You Need Our comprehensive on-line RoHS Customer Support Center provides a forum to answer your questions and support your RoHS needs. RoHS FQ (Frequently sked Questions) is available with links to more detailed information. You can also submit RoHS questions and receive a response within 24 hours during a normal work week. The Support Center also provides: Cross-Reference from Non-compliant to Compliant Products bility to browse RoHS Compliant Products in our on-line catalog Downloadable Technical Data Customer Information Presentation More detailed information regarding the definitions used above RoHS Customer Support Center So whatever your questions when it comes to RoHS, we ve got the answers at 4

5 Introduction (Continued) Mass termination capabilities of the ribbon cable connectors have helped make ribbon cable, and particularly.050 [0.127] centerline cable, popular within the electronics industry. The ability to terminate up to 64 conductors simultaneously, without stripping or otherwise pre-paring the cable, presents obvious labor savings. Ribbon Cable Connectors are wire-to-board devices used to make the transition between cable and pc board circuitry. They find heavy use within equipment to connect one board to another or one subsystem to another. The connectors are also used in input/output applications, connecting different pieces of equipment. Ribbon Cable Solutions are available on three separate cable centerline spacings. They include:.025 [0.64] Centerlines System 50 receptacles System 50 paddleboards Pin headers.039 [1.00] Centerlines 2.0 mm receptacles Breakaway pin headers.050 [1.27] Centerlines 50/50 Grid connectors Micro-MaTch connectors MP-LTCH novo receptacle connectors DIP plugs EUROLTCH receptacle connectors per DIN and IEC Pin Headers System 50 ribbon cable receptacles will terminate cable on.025 [0.64] centerlines. They are available in select sizes from 20 thru 100-positions, and accept wire size range 30 WG [0.05 mm2] solid or stranded wire and 32 WG [0.03 mm2] stranded pvc insulated wire. Housing and cover are made of high temperature tolerant thermoplastic material, black, UL 94V-0 rated. single mating beam, phosphor bronze contact provides the interconnect between the conductor and the.0152 [0.382] posts on.050 x [1.27 x 2.54] grid. lso available in paddleboard configurations. 2.0 mm [.079] ribbon cable receptacles feature contacts on a true 2.0 mm [.079 in.] mating grid for 1.0 mm [.039 in.] pitch ribbon cable. Select configurations are available between 8 and 50-positions. Receptacles feature insulation displacement contacts (IDC). 50/50 Grid connectors lthough MPMODU 50/50 grid vertical headers and Receptacles are designed for parallel board-to-board stacking in high density applications, Right-angle board-to-board and cableto-board applications are also possible since the vertical receptacles also mate with non-latching right-angle headers and the vertical headers also mate with non-latching cable connectors. Micro-Match connectors Miniaturization and the trend towards higher density of electronic functions on a substrate led to the introduction of the Micro-MaTch connector. The system offers a range of board and wire connectors, enabling a variety of wire-to-board and board-to-board interconnections. Its design prevents the traditional failure mode in tin-plated connections, fretting corrosion. n additional positioning spring in the female part absorbs relative movements caused by vibrations and thermal expansion between male and female contacts. By preventing movements on the contact spot, a gas tight connection can be guaranteed under all circumstances. MP-LTCH novo receptacles feature two rows of contacts on x [2.54 x 2.54] centers on selected sizes of 10 thru 64-positions and mate with.025 [0.64] square or round posts. The MP-LTCH novo tuningfork contact offers a military-approved design, at an affordable cost. Polarization options include military, center and military, or dual bar. DIP (Dual In-Line Package) plugs provide a permanent connection of ribbon cable to a pc board or mating to DIP sockets. Using the same centerline dimensions as DIP integrated circuits, DIP plugs offer space efficiency and a low profile of.253 [6.43]. Need more information? Call Technical Support at the numbers listed below. Technical Support is staffed with specialists well versed in all Tyco Electronics products. They can provide you with: Technical Support Catalogs Technical Documents Product Samples Tyco Electronics uthorized Distributor Locations 5

6 Table of Contents Ribbon Cable Connector Selection Guide , [0.64] Centerline Ribbon Cable Connectors System 50 Connectors Cable-to-Board Connectors , 9, 12 Board-to-Board Connectors , 11 Ultra T compliant Bus Connectors [1.00] Centerline Ribbon Cable Connectors 2 mm [.079] Receptacle Connectors , 17 MPMODU 50/50 Grid Connector System Introduction Board-to-Board Vertical Receptacles and Headers Board-to-Board Vertical Receptacles, Double Row,.050 x.050 [1.27 x 1.27] Centers Board-to-Board Vertical Headers, Double Row,.050 x.050 [1.27 x 1.27] Centers.. 21 Recommended PC Board Layouts for Vertical Connectors Board-to-Board Right-ngle Headers Board-to-Board Right-ngle Headers, Double Row,.050 x.050 [1.27 x 1.27] Centers Cable-to-Board Connectors Cable-to-Board Receptacle Connectors, Double Row,.050 x.050 [1.27 x 1.27] Centers Terminating Covers for Cable Connectors pplication Tooling for Cable Connectors Performance Specifications Technical Documents Micro-MaTch Connector System Miniature Connector System System Overview/Technical Data pplications (3 Dimensions) pplications (2 Dimensions) Female-on-Board Connector, Top Entry Female-on-Board Connector, Side Entry Female-on-Board Connector Surface Mount Device (SMD) Male-on-Board Connector Male-on-Wire Connector Paddle Board Connector Crimp On Snap In (COSI) Connector Specials pplication Tooling , 43 Lead ssembly and Sample Box [1.27] Centerline Ribbon Cable Connectors Universal I/O Pin Connectors without Mounting Ears Universal I/O Pin Connectors with Slotted Mounting Ears EUROLTCH Receptacles 64-Position (Three-Row Housings, Two Rows Loaded) MP-LTCH Novo Connectors Military Polarized, x [2.54 x 2.54] Centers Center and Military Polarized, x [2.54 x 2.54] Centers Dual Polarized, x [2.54 x 2.54] Centers Female Socket Connectors, x [2.54 x 2.54] Centers, 622 and 636 Series.. 52, 53 Female Socket Connectors, x [2.54 x 2.54] Centers, 609 Series , 55 DIP Plugs, x [2.54 x 2.54] Centers, 609 Series DIP Plugs, x [2.54 x 2.54] Centers, 622 Series

7 Table of Contents (Continued).050 [1.27] Centerline Ribbon Cable Connectors (Continued) DIP Plugs, x [2.54 x 2.54] Centers DIP Plugs, x.300 [2.54 x 7.62] Centers DIP Plugs, x.600 [2.54 x 15.24] Centers Row PCB Solder Transition Connectors Row Horizontal Receptacle ccessories Flexible Pull Tabs Universal I/O Latches Military Polarizers Keying Plugs Strain Relief for 622 Series DIP Plugs Pull Loops, Permanent (For Receptacles and Pin Connectors) Strain Relief for Universal I/O without Mounting Ears Strain Relief for 609 Series (Tulip Contact) Female Socket Connectors Strain Relief for MP-LTCH Novo and Ultra T compliant Bus Connectors Strain Relief for 2 mm Strain Relief for 622 and 636 Series Female Socket Connectors pplication Tooling Low Profile Headers Low Profile Pin Headers, Center and Dual Polarized, x [2.54 x 2.54] Centerlines , 77 Low Profile Pin Headers, Center and Dual Polarized, x [2.54 x 2.54] Centerlines and Kinked Solder Tails for PCB Retention , 79 IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches, Military and Center Polarized, x [2.54 x 2.54] Centerlines , 81 IDC Low Profile Ejection Style Pin Headers, Center Polarized, x [2.54 x 2.54] Centerlines , 83 Universal Ejection Style Pin Headers and Pinless Headers Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines Universal Ejection Style Pin Headers, CTION PIN Contacts, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines , 88 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines, Right-ngle Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines , 93 Universal Ejection Style Pin Headers, with PCT Housing, x [2.54 x 2.54] Centerlines,.025 [0.64] Sq. Posts (Mating End) , 95 Latches for Ejection Style Universal Pin Headers and Pinless Headers Cable Solutions , 98 Part Number Index

8 System 50 Cable-to-Board Connectors,.025 [0.64] Centerline Ribbon Cable.025 [0.64] Centerline Ribbon Cable Connectors System 50 Cable-to-Board Connectors Product Facts Preassembled housing and cover One-step termination End and daisy chain termination Positive end latching of connector to universal header Terminates 30 WG [0.05 mm2] solid or stranded and 32 WG [0.03 mm2] stranded.025 [0.64] centerline ribbon cable with PVC insulation Connectors are RoHS compliant Recognized under the Component Program of the Underwriters R Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards ssociation, File No. LR 7189 R The System 50 Ribbon Cable connector is a receptacle connector that will terminate ribbon cable on.025 [0.64] centerlines. It is available in select sizes from 10 to 100 positions and will accommodate 30 WG [0.05 mm2] solid or stranded and 32 WG [0.03 mm2] stranded conductors with PVC cable insulation. The housing and cover are of a high temperature tolerant thermoplastic (black) with a UL 94V-0 rating. phosphor bronze single mating beam contact provides the interconnect between the conductor and the.015 [0.38] square posts on the.050 x [1.27 x 2.54] grid. The contacts are plated with 30 gold duplex plating. The latching feature is located on the receptacle, not the header, and saves board space and eliminates future problems of latch height compatibility. 8

9 System 50 Cable-to-Board Connectors,.025 [0.64] Centerline Ribbon Cable (Continued) Double Row Receptacle Material and Finish Housing Black thermoplastic, UL 94V-0 rated Latches Stainless steel Contacts Phosphor bronze, plated 30 microinch gold over nickel with tin in termination area Related Product Data Mateable Connectors See Tyco Electronics Catalog See Part Numbers and Series on pages 10 and 11 Mates with Posts.015 [0.38] square,.125 [3.18] long, on.050 x [1.27 x 2.54] grid Technical Documents Product Specification pplication Specification [6.45].054 [1.37].228 [5.79].430 [10.92].335 [8.51] Position #1 Indicator B C F No. of Dimensions Pos. B C D E F See pplication Specification for termination tooling. Note: ll part numbers are RoHS compliant. Part Number [2.59] E Cover Latch Contact Housing.198 [5.03].228 [5.80].246 [6.25].580 [14.73] Before Termination.050 Typ. [1.27] D [0.64] Centerline Ribbon Cable Connectors System 50 Cable-to-Board Connectors

10 System 50 Board-to-Board Connectors, Through-Hole Headers Shrouded, Double Row Vertical.015 [0.38].390 [9.91].025 [0.64] Centerline Ribbon Cable Connectors System 50 Board-to-Board Connectors Material and Finish Housing Black thermoplastic, UL 94V-0 rated Contacts Copper alloy, plated [ ] gold in mating area, [ ] tin on solder posts, with entire contact underplated [ ] nickel Related Product Data Mateable Receptacles page 9 Technical Documents Product Specification pplication Specification [1.52] 2 Plc. Circuit Identification Feature** No. of Dim. Part Positions Number **Point of measurement for gold thickness. **Circuit identification feature omitted on 8, 10, 12 and 14 position headers. Note: ll part numbers are RoHS compliant..050 [1.27] Typ..284 [7.21].055* [1.40].344 [8.74].092 [2.34] No. of Dim. Part Positions Number

11 System 50 Board-to-Board Connectors, Through-Hole Headers (Continued) Shrouded, Double Row Right-ngle at Post Tips Material and Finish Housing Black thermoplastic, UL 94V-0 rated Contacts Copper alloy, plated [ ] gold in mating area, [ ] tin on solder posts, with entire contact underplated [ ] nickel Related Product Data Mateable Receptacles page 9 Technical Documents Product Specification pplication Specification [13.72].060 [1.52] 2 Plc..050 [1.27] Typ. Circuit Identification Feature** Note 1 Note 2 No. of Dim. Part Positions Number **Point of measurement for gold thickness. **Circuit identification feature omitted on 8, 10, 12 and 14 position headers. Notes: 1. Hold down posts located as shown for 16 through 100 position headers. Notes: 2. Hold down posts located as shown for 8 through 14 and 60 through 100 position headers. Notes: 3. ll part numbers are RoHS compliant..055* [1.40].290 [7.37].350 [8.89].160 [4.06] at Post Tips.408 [10.36] Hold down post No. of Dim. Part Positions Number [0.64] Centerline Ribbon Cable Connectors System 50 Board-to-Board Connectors

12 System 50 Cable-to-Board Connectors,.025 [0.64] Centerline Ribbon Cable Paddleboard.025 [0.64] Centerline Ribbon Cable Connectors System 50 Cable-to-Board Connectors Material and Finish Housing LCP thermoplastic, UL 94V-0 rated, black Cover Polyester, UL 94V-0 rated, black Contacts Phosphor bronze, plated [ ] min. tin over [ ] min. nickel underplating Technical Documents Product Specification pplication Specification [7.72].075 [1.91] Typ..050 [1.27].045 [1.19] Ref..050 [1.27] Typ..031 [0.79] Typ. Position 1 Indicator Printed Circuit Board Hole Layout #1 No. of PCB Dimensions Part Pos. Layout B Number B Typ. [0.61] [1.27] Typ. B.304 [7.72].075 [1.91] Typ..020 [0.51].040 [1.02].273 [6.93] (Terminated).168 [4.27].050 [1.27] Typ..008 [0.20] Typ..118 [3.00] B.031 [0.79] Typ..304 [7.72] Printed Circuit Board Hole Layout #2.340 [8.64] (Unterminated).075 [1.91] Typ..030 [0.76] Standoffs (Various Locations) No. of PCB Dimensions Part Pos. Layout B Number See pplication Specification for termination tooling. Note: ll part numbers are RoHS compliant. 12

13 Ultra T Compliant Bus Connectors,.025 [0.64] Centerline Ribbon Cable Product Facts IDC termination Backward compatible with current IDE Interfaces Improved signal integrity: 1 to 1 signal to ground ratio Improved crosstalk when compared to existing IDE Cable ssembly Color coded connectors for System board, and Master HDD and Slave HDD Cable impedance 80 ohms Up to 3 connectors per cable assembly 15 microinches gold plating Recognized under the Component Program of the Underwriters R Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards R ssociation, File No. LR 7189 Terminates 30 WG solid or stranded PVC insulated 80 conductor ribbon cable Ultra T is the next generation IDE (Integrated Drive Electronics) bus. The current IDE bus has a maximum data transfer rate of about 16.5 MB/second. s the bus speeds and disk drive performances increase, the cable assembly between the motherboard and hard drive becomes a limiting factor in data transfer from the drive. The Ultra T compliant connector and cable assembly from Tyco Electronics provide the customer with improved electrical performance by creating a 1:1 signal-toground ratio. The connector design incorporates an IDC bus bar to common the 40 additional ground signals. The cable is.025" centerline PVC ribbon cable. The connector is fully backward compatible with existing 40- position headers with pin 20 removed on motherboards and disk drives. The new connectors are color coded to identify: 1. system board connector 2. primary or master hard drive connector 3. slave drive connector Standard Issues The Ultra T compliant cable performance specification is part of the Small Form Factor Committee No Contacts vailable: 80 position IDC contact terminations 40 signal contacts 40 ground terminations to special IDC bus bar.025 [0.64] Centerline Ribbon Cable Connectors Ultra T Compliant Bus Connectors 13

14 Ultra T Compliant Bus Connectors,.025 [0.64] Centerline Ribbon Cable Related Product Data Strain Relief Part Number Mateable Headers page 15 Terminated View.420 [10.67].492 Max. [12.50].025 [0.64] Centerline Ribbon Cable Connectors Ultra T Compliant Bus Connectors Material & Finish Housing and Cover Thermoplastic, UL 94 V-0 rated, color per table Contacts Phosphor bronze, plated gold per table on mating end, [ ]min. tin in wire termination area, over [ ] min nickel on entire contact. Technical Documents Product Specification pplication Specification See pplication Specification for termination tooling. ccessories Strain Relief page 68 Keying Plug page 64 Pull Loops page 66 Pull Tabs page 63 Cover Housing Pos. No. 1 Indicator Configuration Configuration B Pin 34 Conductor Cut per SFF-8049 Odd Gnd Optional Center* Polarizer Bar 1.90 [48.26] System Board Connector System Board Connector [55.52] Contact.610 Ref. [15.49] Circuit 20 Molded Shut Color Coded Position 1 Position 1 Position 1 Conductor No. 1 Master or Primary Connector Slave Connector.240 [6.10] Slave Connector Master or Primary Connector Ground Bus Bar Signal Contacts *Center & Military Polarized Military Polarized Connector Type 15µ" Gold Housing Cover 15µ" Gold Housing Cover Color Color Color Color System Board Blue Black Blue Black Primary or Master Black Black Black Black Slave Gray Black Gray Black Notes: 1. ll connectors are ODD GROUND configuration, ie. all odd cable conductors are grounded. EVEN GROUND connectors are not available. See Customer Drawings for detailed electrical connection descriptions. 2. ll part numbers are RoHS compliant. 14

15 Ultra T Compliant Bus Connectors,.025 [0.64] Centerline Ribbon Cable (Continued) Ultra T Compatible Headers Universal Headers Pin 20 Omitted Post Housing Latch Part Contact Finish Solder Tail Type Material Type Number (Plating Code) Length Vertical Nylon or PBT Long D Vertical Nylon or PBT Short B Legend: PP Polarization Peg Comments PP Low Profile Headers Pin 20 Omitted Post Housing Latch Part Contact Finish Solder Tail Housing Type Material Type Number (Plating Code) Length Color Vertical Nylon None Black Vertical Nylon None B Black Vertical Nylon 6T None C Black Vertical Nylon 6T None C Blue Vertical Nylon None C Black Vertical Nylon None C Blue Plating Code Duplex plated, gold flash on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel. Plating Code B Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel. Plating Code C Gold flash over nickel underplate on entire post. Plating Code D Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel..025 [0.64] Centerline Ribbon Cable Connectors Ultra T Compliant Bus Connectors Note: ll part numbers are RoHS compliant. 15

16 METRIC Dimensions are 2.0 mm [.079] Receptacle Connectors.039 [1.00] Centerline Ribbon Cable Connectors.079 [2.00] Receptacle Connectors Product Facts True hard metric 2.0 x 2.0 [.079 x.079] mating grid for 1.0 [.039] pitch ribbon cable Wide selection of configurations, 8-50 positions Insulation displacement (IDC), beryllium copper contacts, duplex plated gold-over-nickel Top/bottom single beam contact orientation UL 94V-0 rated thermoplastic components ssemblies are furnished preassembled with termination covers Optional polarization Optional strain relief available Connector assemblies packaged for ease of handling and protection Recognized under the Component Program of the Underwriters R Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards R ssociation, File No. LR 7189 Performance Data Durability 150 cycles Termination Resistance 25 milliohms max. Mating Force 1.67 N max. per contact Unmating Force 0.14 N min. per contact Operating Temperature -65 C to +105 C Technical Documents Product Specification pplication Specification The 2.0 [.079] receptacle connector family features contacts on a true 2.0 x 2.0 [.079 x.079] mating grid for 1.0 [.039] pitch 28 WG ribbon cable. variety of configurations are available from 8 through 50 positions. This small, compact connector is finding wide acceptance throughout the electronic industry, particularly in the smaller laptop and notebook type computers with 63.5 [2.5] drives. Other areas of application include point-of-sale terminals, fax machines, photocopiers, printers, consumer electronics, and other computer peripheral equipment. These receptacles feature insulation displacement contacts (IDC) with a top/bottom single-beam contact orientation. Contacts are beryllium copper, duplex plated [ ] gold in the mating area and [ ] min. tin on termination end, all over [ ] nickel underplating. Contact mating area is 1.54 [.061] from the face of the housing and they accept 0.50mm [.0197] round or square posts. Housings are made of UL 94V-0 rated polyester with optional center bar polarization. Complete assemblies are furnished preassembled with termination covers. The complete assembly presents a compact design only 5.2 [.203] wide over the termination cover by 4 [.157] deep by 4 [.157] wide mating end. Terminated height is 8.48 [.334]. Optional strain relief available. ssemblies are packaged for ease of handling and protection. 16

17 METRIC Dimensions are 2.0 mm [.079] Receptacle Connectors, Non-Polarized and Center Polarized Bar Material and Finish Housing and Termination Cover UL 94V-0 rated polyester, black Contacts Beryllium copper, duplex plated [ ] min. gold on mating end, [ ] min. gold on termination end, all underplated [ ] min. nickel Note: ccepts mm2 [28 WG] ribbon cable, PVC insulated 1.00 [.039] pitch. See pplication Specification for details. Technical Documents Product Specification pplication Specification Mateable Connectors pages 9 and 12, or see pplication Specification for header requirements ccessories Pull Loops page 66 Keying Plugs page 64 Strain Relief page [.403] 5.16 [.203] [.1575] Position Number [.079] Typ [.079] Typ. Position Number 1 Indicator B Optional Center Polarizer Bar 1.90 ± 0.05 [.075 ±.002] No. of Dimensions Center Positions B Polarized Non-Polarized Note: ll part numbers are RoHS compliant [.197] 1.54 [.061] Terminated View, Typical 8.48 [.334].039 [1.00] Centerline Ribbon Cable Connectors.079 [2.00] Receptacle Connectors 17

18 MPMODU 50/50 Grid Connector System Right-ngle Headers, Board-to-Board (Page 24) Vertical Headers, Board-to-Board (Page 21) Board-to-Board Vertical Receptacles and Headers Receptacles, Cable-to-Board, With Latch (Page 26) Vertical Receptacles, Board-to-Board (Page 20) Vertical Headers, Board-to-Board (Page 21):.250 [6.35] Stack Height.320 [8.13] Stack Height.390 [9.91] Stack Height Receptacles, Cable-to-Board Without Latch (Page 26) Vertical Headers, Board-to-Board (Page 21) Vertical Receptacles, Board-to-Board (Page 20) Produced under a Quality Management System certified to ISO 9001 copy of the certificate is available upon request. ISO 9001 Certified 18

19 Board-to-Board Vertical Receptacles and Headers Product Facts Surface-mount products for parallel board-to-board applications, as well as right-angle board-to-board and cable-to-board applications High density.050 x.050 [1.27x1.27] centerline grid Three board-to-board stack heights:.250 [6.35],.320 [8.13] and.390 [9.91] Non-protrusive metallic holddowns Reliable dual beam receptacle contacts for redundant contact Duplex plated receptacle and post contacts; gold plated on mating areas, tin plated on tails Compatible with standard surface-mount processing (VPR and IR) Receptacle and header allow for drainage of processing fluids Tape and reel packaging available. Contact Tyco Electronics for details Polarized header and receptacle assemblies Sizes of 10, 20, 30, 40, 50, 60, 70, 80 and 100 positions Recognized under the Component Program of Underwriters Laboratories Inc., R File No. E28476 Certified by Canadian Standards ssociation R File No. LR7189 MPMODU 50/50 Grid Vertical Headers and Receptacles are designed for parallel board-to-board stacking in high density applications. Right-angle board-to-board and cable-to-board applications are also possible, since the vertical receptacles also mate with non-latching right-angle headers (page 24) and the vertical headers also mate with non-latching cable connectors. vailable are double row, vertical shrouded headers and receptacles in sizes ranging from 10 through 100 positions (in 10 position increments). Parallel board-to-board stack heights of.250 [6.35],.320 [8.13] and.390 [9.91] are achievable by selection of the appropriate header. The receptacle is the same for all three stack height headers. Non-protrusive metallic holddowns are designed for use in.062 [1.57] or thicker PC boards and allow surface mounting to both sides of the board. In addition to providing retention during processing, the holddowns are soldered during reflow and therefore provide long-term strain relief for the solder joints. MPMODU 50/50 Grid Vertical Headers and Receptacles are designed to be compatible with standard surface-mount processes; IR (infrared) and VPR (vapor phase reflow). The surface-mount connectors have been designed so that dimensioning, tolerances, referenced datums, holddown characteristics Non-Protrusive Metallic Holddowns and packaging methods result in a system that is compatible with robotic assembly. The headers and receptacles feature polarization to prevent misalignment. Three Board Stack Heights.250±.006 [6.35±0.15].320±.006 [8.13±0.15].390±.006 [9.91±0.15] 19 Board-to-Board Vertical Receptacles and Headers

20 Board-to-Board Vertical Receptacles, Double Row,.050 x.050 [1.27 x 1.27] Centerline.120 [3.05].028 [0.71] Vertical Receptacles, Double Row Material and Finish Housing Glass-filled thermoplastic, black, 94V-0 rated Contacts Copper alloy; duplex plated [ ] gold in mating area, [ ] tin on solder tail, with entire contact underplated [ ] nickel Holddown Copper alloy; plated [ ] tin over [ ] nickel Related Product Data Mating Headers pages 21 and 24 PC Board Layouts page 22 Performance Specifications page 29 Technical Documents page 29 Product Specification pplication Specification Packaging Tube or Tape and Reel No. of Pos..050 [1.27] Dimension.050 [1.27].050 [1.27] Polarizing Tab (For Polarization to Mating Header).187 [4.75] Receptacle Part Numbers Tube Tape and Reel* No Hold Down w/vacuum Cover [6.75] [13.11] [19.46] [25.81] [32.16] [38.51] [44.86] [51.21] [63.91] * Parts packaged in tape and reel have vacuum pick and place cover. See PC Board Layout on page Note: ll part numbers are RoHS compliant.

21 Board-to-Board Vertical Headers, Double Row,.050 x.050 [1.27 x 1.27] Centerline.050 [1.27].225 [5.71] For.250 [6.35] Mated Height.2255 [5.728].050 [1.27] For.320 [8.13] Mated Height For.390 [9.91] Mated Height Material and Finish Housing Glass-filled thermoplastic, black, 94V-0 rated Contacts Copper alloy; duplex plated [ ] gold in mating area, [ ] tin on solder tail, with entire contact underplated [ ] nickel Holddown Copper alloy; plated [ ] tin over [ ] nickel.2975 [7.557].3675 [9.335] Related Product Data Mating Receptacles pages 20 and 26 (without latch only) PC Board Layouts page 22 Performance Specifications page 29 Note: ll part numbers are RoHS compliant. Technical Documents page 29 Product Specification pplication Specification Packaging Tube or Tape and Reel Header Part Numbers No. of Dimension.250 [6.35] Mated Height.320 [8.13] Mated Height.390 [9.91] Mated Height Pos. Tape & Reel* Tubes Tubes Tubes Tape & Reel* Hold Down No Hold Down Hold Down No Hold Down Tape & Reel* [9.44] [15.79] [22.14] [28.49] [34.84] [41.19] [47.54] [53.89] [60.24] [66.59] *Parts packaged in tape and reel have vacuum pick and place cover. See PC Board Layout on page [0.76].030 [0.76].030 [0.76].050 [1.27].050 [1.27].050 [1.27] 21 Vertical Headers, Double Row

22 Recommended PC Board Layouts for Vertical Connectors Headers.029 [0.74] B Spaces at.050 [1.27] = C.050 [1.27].162 [4.11].010 [0.25] 4 Plc. Recommended PC Board Layouts.182 [4.62].091 [2.31] Receptacles B Spaces at.050 [1.27] = C.130 [3.30].065 [1.65].029 [0.74].050 [1.27] No. of Receptacle Dimensions Header Dimensions Pos. B C D B C D D D Detail.061 [1.54] Detail.060 [1.52].110 [2.79] CL of Pattern CL of Pattern Detail.047 [1.19] 2 Plc [5.08].320 [8.12] [5.08].322 [8.17] [11.43].570 [14.48] [11.43].572 [14.52] [17.78].820 [20.83] [17.78].822 [20.87] [24.13] [27.19] [24.13] [27.22] [30.48] [33.53] [30.48] [33.57] [36.83] [39.88] [36.83] [39.92] [43.18] [46.23] [43.18] [46.27] [49.53] [52.58] [49.53] [52.62] [55.88] [58.93] [55.88] [58.97] [62.23] [65.28] [62.23] [65.32] 22 Note: Refer to Tyco Electronics Customer Drawings for additional PC board layout information and dimensional tolerances.

23 Board-to-Board Right-ngle Headers Product Facts Surface-mount products for right-angle board-to-board and cable-to-board applications Double-row, right-angle shrouded headers High density.050 x.050 [1.27 x 1.27] centerline grid Latching and non-latching versions available Non-protrusive metallic holddowns Metallic tabs, when soldered to PC board pad, provide added mechanical support Duplex plated post contacts; gold plated on mating area, tin plated on tails Compatible with standard surface-mount processing (VPR and IR) Standoffs on header housings allow for drainage of processing fluids ll headers are polarized Sizes of 10, 20, 30, 40, 50, 60, 70, 80 and 100 positions Recognized under the Component Program of Underwriters R Laboratories Inc., File No. E28476 Certified by Canadian Standards ssociation R File No. LR7189 MPMODU 50/50 Grid Right-ngle Headers will accommodate a variety of high density packaging applications; right-angle board-to-board applications when mated with vertical receptacles (page 20) and right-angle cable-to-board applications when mated with cable connectors (page 26). The small.050 x.050 [1.27 x 1.27] centerline contact spacing allows efficient use of the PC board area. Mechanical support of the headers to the PC board is provided by non-protrusive metallic holddowns designed for.062 [1.57] or thicker PC boards. These holddowns are of the same design as those used in the vertical headers (page 21) and receptacles (page 20). There are also metallic tabs that are soldered to the surfaces of the PC board pads for added support. MPMODU 50/50 Grid Right-ngle Headers are available in double-row, in either latching or nonlatching versions, and in sizes ranging from 10 through 100 positions (in 10 position increments). The latching version provides positive retention when mated with the latching cable connector (page 26). ll headers feature polarization to help prevent misalignment during mating. Board-to-Board Right-ngle Headers 23

24 Board-to-Board Right-ngle Headers, Double Row,.050 x.050 [1.27 x 1.27] Centerline Non-Latching Header.050 [1.27].050 [1.27] Typ..213 [5.41] Right-ngle Headers, Double Row, Latching and Non-Latching Latching Header Material and Finish Housing Liquid crystal polymer, black, 94V-0 rated Contacts Copper alloy; duplex plated [ ] gold in mating area, [ ] tin on solder tail, with entire contact underplated [ ] nickel Holddown Copper alloy; plated [ ] tin over [ ] nickel Related Product Data Mating Receptacles pages 20 and 26 Performance Specifications page 29 Technical Documents page 29 Product Specification pplication Specification Packaging Tube.430 [10.92] Recommended PC Board Layout No. of Pos..340 [8.64].140 [3.56] Min Note: Refer to Tyco Electronics Customer Drawings for additional PC board layout information and dimensional tolerances..029 [0.74] Typ.065 [1.65] Typ. B Spaces at.025 = C [0.64].085 [2.16].175 [4.45] Dimensions B C D.305 [7.75] Header Part Numbers Latching Non-Latching [16.00] [5.72].550 [13.97] [22.35] [12.07].800 [20.32] [28.70] [18.42] [26.67] [35.05] [24.77] [33.02] [41.40] [31.12] [39.37] [47.75] [37.47] [45.72] [54.10] [43.82] [52.07] [60.45] [50.17] [58.42] [73.15] [62.87] [71.12] D.063 [1.57] (2 Plc).047 Dia [1.19] Plated-Thru Hole (2 Plc).190 [4.83] (2 Plc).136 [3.45] (2 Plc).352 [8.94].050 [1.27] 24 Note: ll part numbers are RoHS compliant.

25 Cable-to-Board Connectors Product Facts Double-row receptacle connectors provide cableto-board connection capabilities for vertical headers (non-latching) and right-angle headers (latching and non-latching) IDC (Insulation Displacement Crimp) mass termination of solid or stranded round conductor.050 [1.27] centerline ribbon cable with PVC or polyethylene insulation ccommodates ribbon cable conductor sizes of 28 WG [ mm2] and 30 WG [0.05 mm2] and insulation diameters up to.036 [0.91] maximum Reliable single beam receptacle contact design Duplex plated receptacle contacts; gold plated in mating area, tin in termination area Terminating covers (sold separately) provide both strain relief and protection to the termination area Sizes of 10, 20, 30, 40, 50, 60, 70, 80 and 100 positions Connectors available with or without metal latch Connectors without latches are polarized to help prevent mismating Recognized under the Component Program of Underwriters Laboratories Inc., R File No. E28476 Certified by Canadian Standards R ssociation File No. LR7189 These double-row cable connectors, with a.050 x.050 [1.27 x 1.27] centerline contact spacing, provide cable-to-board connection capabilities for the MPMODU 50/50 Grid Connector System. Cable connectors without a latch will mate with the vertical headers (page 21), while cable connectors with or without a latch can be used to mate with the right-angle headers (page 24). The cable connectors feature reliable singlebeam IDC (insulation displacement crimp) contacts which are duplex plated with [ ] gold. These contacts can be mass terminated to either solid or stranded round conductor ribbon cable with conductor sizes of 28 WG [ mm2] and 30 WG [0.05 mm2] and a maximum insulation diameter of.036 [0.91]. During termination, the terminating covers, which must be purchased separately, assist in guiding the wire into the IDC contacts, then provide strain relief when fully seated. ctual termination is accomplished with the Tyco Electronics manual tooling shown on page 28. The latching version of the cable connector is equipped with a metal latch which provides positive retention of the receptacle cable connector when mated with a surfacemounted right-angle header. The cable connector without a metal latch features polarization to help prevent mismating. ll connectors are available in sizes ranging from 10 through 100 positions (in 10 position increments). Cable-to-Board Connectors 25

26 Cable-to-Board Receptacle Connectors, Double Row,.050 x.050 [1.27 x 1.27] Centerline Receptacle Connectors, Double Row, With and Without Latch Material and Finish Housing Thermoplastic, black, 94V-0 rated Latch Stainless steel Contacts Phosphor bronze; duplex plated [ ] minimum gold in mating area, [ ] minimum tin on solder tail, with entire contact underplated [ ] minimum nickel Related Product Data Mating Headers pages 21 and 24 (latching) Terminating Covers (Must be Purchased Separately, 2 Required per Connector) page 27 Termination Tooling page 28 Performance Specifications page 29 Technical Documents page 29 Product Specification pplication Specification , Packaging Tube No. of Pos. D B Spaces at.050 [1.27] = C.050 [1.27] Typ.280 [7.11].284 [7.21].050 [1.27].627 [15.94].327 [8.31] Dimensions B C D.690 [17.56].120 [3.05] Receptacle Part Numbers With Latch Without Latch [14.68] [5.08].266 [6.76] [21.03] [11.43].516 [13.11] [27.38] [17.78].766 [19.46] [33.73] [24.13] [25.81] [40.08] [30.48] [32.16] [46.43] [36.83] [38.51] [52.78] [43.18] [44.86] [59.13] [49.53] [51.21] [71.83] [62.23] [63.91] Note: ll part numbers are RoHS compliant.

27 Terminating Covers for Cable Connectors Material Glass-filled thermoplastic, black, 94V-0 rated Related Product Data Connectors used with Covers page 26 Termination Tooling page 28 Technical Documents page 29 Product Specification pplication Specification , Packaging Plastic bag.191 [4.85].277 [7.04] No. of Dimension Terminator Cover Pos. Part Numbers [14.35] [20.70] [27.05] [33.82] [39.75] [46.10] [52.45] [58.80] [71.50] Note: Terminating covers must be purchased separately, two are required for each cable connector. Cable Conncetor Terminating Cover, Double Row Note: ll part numbers are RoHS compliant. 27

28 pplication Tooling for Cable Connectors IDC (Insulation Displacement Crimp) Tooling The Manual Miniature pplication Frame ssembly , equipped with a Cover Closing Kit , is used for the IDC termination of ribbon cable to the cable connectors shown on page 26. Prior to termination, the covers must be partially assembled onto a connector housing, the cable inserted between the covers and contacts and the covers preclosed by hand, clamping the cable in place. In the Manual Miniature pplication Frame ssembly, the covers are fully seated to complete the mass termination and provide strain relief for the completed connection. For tooling information, call Technical Support Center Note: Refer to Tyco Electonics Instruction Sheets (frame assembly ) and (cover closing kit ) for complete termination/tooling information. Manual Miniature pplication Frame ssembly with Cover Closing Kit Note: ll part numbers are RoHS compliant.

29 Performance Specifications Board-to-Board Connectors, Vertical and Right-ngle Mating Force 6.4 oz (1.78 N] max. per contact Unmating Force 1.0 oz [0.28 N] min. per contact Durability Tested to 200 cycles min. Current Rating (30 C T rise):.5 ampere per contact Operating Temperature Range -65 C to +105 C Termination Resistance 16 milliohms max. (initial) Insulation Resistance 5000 megohms min. (initial) Dielectric Withstanding Voltage 300 VC Cable-to-Board Connectors Mating Force 6.4 oz (1.78 N] max. per contact Unmating Force Without Latch.5 oz [0.14 N] min. per contact Durability Tested to 200 cycles min. Current Rating (10 C T rise);.5 ampere per contact Operating Temperature Range -65 C to +105 C Termination Resistance 25 milliohms max. (initial and final) Insulation Resistance 5000 megohms min. (initial) Dielectric Withstanding Voltage 300 VC Technical Documents Various technical documents are available for your use: Product Specifications describe technical performance characteristics and verification tests. They are intended for the Design, Component and Quality Engineer MPMODU 50/50 Grid Vertical Board-to-Board Connectors MPMODU 50/50 Grid Right-ngle Board-to-Board and Cable Connectors pplication Specifications describe requirements for using the product in its intended application and/or crimping information. They are intended for the Packaging and Design Engineer and the Machine Setup Person MPMODU 50/50 Grid Connector System Instruction Sheets provide instructions for assembling or applying the product. They are intended for the Manufacturing ssembler or Operator Manual Miniature pplication Frame ssembly Cover Closing Kit Performance Specifications/ Technical Documents Note: ll part numbers are RoHS compliant. 29

30 Micro-MaTch Miniature Connector System Micro-MaTch Miniature Connector System Features/ Benefits vailable in 2 to 20 positions pplicable Wire: 20~28 WG Wire connectors supplied on-tape and suitable for mass termination of 28 WG [0.08 mm2 to 0.09 mm2] ribbon cable Tin plated contact design Guaranteed minimum contact force of 2.0 N Fretting corrosion proof thanks to additional positioning spring member Full range of application tooling from hand tool to fully automated equipment 1. Contact Pin 2. Contact Spring 3. Positioning Miniaturization and the trend towards higher density of electronic functions on a substrate led to the introduction of smaller interconnection systems. The Micro-MaTch connector family, with it s contact spacing of 1.27 mm, fully complies with the electronic packaging requirements of today and the future. The system offers a range of board and wire connectors, enabling a variety of wireto-board and board-toboard interconnections. The Micro-MaTch contact shown on this page is essentially different from other systems available. By its design the traditional failure mode in tin plated connections, fretting corrosion, is prevented. Due to an additional positioning spring in the female part, relative movements caused by vibrations/thermal expansion between male and female contacts are absorbed. By preventing movements on the contact spot, a gas tight connection can be guaranteed under all circumstances. The contact spring is located in the board connector and not in the cable connector, which is usually the case. The counter part, incorporated in the cable connector, is a simple pin, either with an insulation displacement section, suitable for the mass-termination of cable or with a kinked solder leg to be soldered onto a PC Board. The separation of these two basic functions of the contact system contact force generation and wire termination enables the independent optimization of both functions and also leads to relatively simple contact shapes. Because of their shapes contacts can be postplated, leaving no bare edges in the contact and wire slot area. The contact spring system features an additional spring member the positioning spring which compensates positional tolerances. In this way the contact spring can be fully optimized for its basic function, so that the relatively high contact force, required for tin plated contact systems, can be guaranteed under all circumstances. The Micro-MaTch contact spring system is absolutely fretting corrosion proof by its design. 30

31 Micro-MaTch Miniature Connector System Overview Technical Data Technical Data Centerline: Number of Positions: Contact Material: Contact Finish: Housing Material: 1.27 mm (staggered) 4, 6, 8, 10, 12, 14, 16, 18, 20, and some 24 positions Phosphor bronze Tin over Nickel Thermoplastic polyester, red, glass-filled For surface mount versions polyamide 4.6 Flammability rating: per UL 94 V-0 UL-recognized: File E28476 Vol. 23 Section 4 Contact Resistance: 10 MΩ max. Insulation Resistance: MΩ min. Nominal Voltage: 230 V Current Rating: 1.5 max. Temperature Range: -40 C to +105 C (operating) Mating Force: 5N max. per contact Unmating Force: 1N min. per contact Minimum Contact Force: 2N min. Product Specification: pplication Specification: , RoHS Compliance Code: lways RoHS compliant (directive 2002/95/EC) for all types Lead-free Process Capable: Wave solder capable to 265 C for through hole versions reflow solder capable to 260 C for SMD versions PC Board Connectors PC Board Thickness: PC Board Hole Diameter: 1.6 mm nominal 0.8 mm for solder connectors Ribbon Connectors Cable Type: Ribbon cable, UL Style 2651 Conductor Spacing: 1.27 mm (.050") Conductor Diameter: Solid 0.30 mm diameter Stranded 0.08 mm2 7 x mm (other diameters and/or configurations on request) Insulation Type: semi-rigid PVC Insulation Diameter: 0.9 ± 0.1 mm Discrete Wire (COSI) Connectors Cable Type : WG and Micro-MaTch Miniature Connector System Overview Technical Data 31

32 Micro-MaTch Miniature Connector System pplications (3 Dimensions) Male Connectors Micro-MaTch Miniature Connector System pplications (3 Dimensions) Female Connectors Female Top Entry Part Number Female Side Entry Part Number SMD Top Entry Part Number Male-on-Wire Part Number Male-on-Board Part Number / COSI Part Number Part Number Part Number Image Description (see also page 33) 1 Wire-to-Board through hole 2 Board-to-Board through hole 3 Wire-to-Board (discrete wire), through hole 4 Wire-to-Board right angle, through hole 5 Board-to-Board right angle, through hole 6 Board-to-Board right angle, through hole 7 Wire-to-Board right angle (discrete wire), through hole 8 Wire-to-Board surface mount 9 Board-to-Board surface mount, through hole 10 Wire-to-Board (discrete wire), surface mount Paddle Board Part Number

33 Micro-MaTch Miniature Connector System pplications (2 Dimensions) Male Connectors Female Connectors Male-on-Wire Part Number Male-on-Board Part Number COSI Part Number Part Number Part Number Paddle Board Part Number Female Top Entry Part Number Female Side Entry Part Number SMD Top Entry Part Number B B B D C C D F 5 C B B E C D C C C B C D C G Image Dimensions (mm) (max) B (max) C D (max) E (max) F(max) G (max) B 7 B B C E D C D B Micro-MaTch Miniature Connector System pplications (2 Dimensions) 33

34 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Female-on-Board Connector, Top Entry 1.5 [.059] Micro-MaTch Miniature Connector System Female-on-Board Connector, Top Entry This connector version incorporates the Micro- MaTch contact spring system and is designed to be soldered onto PC Boards with a nominal thickness of 1.6 mm. The solder legs are indented, providing firm retention of the connector before and during the soldering operations. s polarization is accomplished directly between the Micro-MaTch male connectors and the PC Board, this top entry female connector does not have any polarizing features. Therefore, the orientation of the connector on the PC Board is irrelevant [.050] B Max [] 0.80 [.031] 1.27 [.050] 2.54 [] 1.40 [.055] Typical Hole Pattern Not Solder Side Shown 3.1 [.122] 5.1 [.200] Max [.071] 1.50 Hole for [.059] Polarization Pin 1.9 [.074] 4.0 [.157] Notes: 1. Connectors are always sideways mounted onto an adhesive tape. 2. Standard packaging quantity is 2500 connectors on a reel with a diameter of 600 mm. 3. t additional charge a special packaging option is available: 250 connectors on a reel with a diameter of 250 mm, packed in a dedicated dispenser box. Mates with: X X X X X X X X No. of Positions Dimensions (mm) Part Numbers B 2500 Connectors/Reel 250 Connectors/Box

35 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Female-on-Board Connector, Side Entry This connector version is identical to the top entry version with two exceptions: The solder legs are parallel to the mating face of the connector instead of perpendicular. It's housing is polarized, so that polarization is accomplished directly between the two mating connectors. Proper orientation of the connectors on the PC Board is relevant here [.039] 2.54 [] 1.27 [.050] B Max [0.09] 1.27 [0.05] 2.54 [0.09] 3.85 [0.15] 3.1 [0.12] 2.54 [0.09] (N-1)x [0.23] 0.80 [0.03] Nom. 5.3 Max. [0.21] Recommended PCB Hole Layout Not Solder Side Shown Notes: 1. Connectors are always sideways mounted onto an adhesive tape. 2. Standard packaging quantity is 2500 connectors on a reel with a diameter of 600 mm. 3. t additional charge a special packaging option is available: 250 connectors on a reel with a diameter of 250 mm, packed in a dedicated dispenser box. Micro-MaTch Miniature Connector System Female-on-Board Connector, Side Entry Mates with: X X X X X X X X No. of Positions Dimensions (mm) Part Numbers B 2500 Connectors/Reel 250 Connectors/Box (1500) (1500)

36 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Female-on-Board Connector Surface Mount Device (SMD) Tape for Vacuum P&P Micro-MaTch Miniature Connector System Female-on-Board Connector Surface Mount Device (SMD) This SMD connector version is designed for standard reflow and infrared solder processes ( FULL SMD ). Polarization is accomplished by the housing, therefor no polarization holes in the PC Board are required. The contact is designed with an additional spring to compensate for differences in thermal expansion between housing and PCB. Due to this feature, tension on solder joints is prevented [.050] =(N-1)* [] 5.0 [.197] 0.5B-2.5 B 1.50 [.059] 1.50 [.059] Recommended PCB Layout Top View 1.90 [.075] 5.0 [.197] 5.0 [.197] 7.0 [.276] 3.00 Minimum [.118] Solder Path Length Notes: 1. To enable automatic pick & placement, connectors are always packed in embossed tape according EI481 specification. 2. Standard packaging quantity is 900 pcs on a reel with a diameter of 330 mm. 3. Connectors are supplied with or without a feature for vacuum Pick & Placement. 4. For this connector no additional solder hold down is required. Mates with: X X X X X X X X No. of Positions Dimensions (mm) Part Numbers B 2500 Connectors/Reel 250 Connectors/Box

37 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Male-on-Board Connector 5.00 [.197] This male connector version is designed to be soldered onto PC Boards with a nominal thickness of 1.6 mm. The solder legs are indented for firm retention of the connector in the PC Board. The connector housing features a polarizing pin on one end for proper orientation of this connector version [] 1.27 [.050] Section - B 2.54 [] 2.54 [] 6.75 [.266] 0.80 [.031] Typical Hole Pattern Not Solder Side Shown 7.10 [.280] 1.27 [.050] Notes: 1. To enable automatic pick & placement, connectors are always packed in embossed tape according EI481 specification. 2. Standard packaging quantity is 900 pcs on a reel with a diameter of 330 mm. 3. Connectors are supplied with or without a feature for vacuum pick & placement. 4. For this connector no additional solder hold down is required. Micro-MaTch Miniature Connector System Male-on-Board Connector Mates with: X X X X X X X X No. of Positions Dimensions (mm) Part Numbers B 2500 Connectors/Reel 250 Connectors/Box

38 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Male-on-Wire Connector Micro-MaTch Miniature Connector System Male-on-Wire Connector For the wire connection, a well-known type blade with a single slot is used. The insides of the slots are tin plated for stable and reliable connections. The connector is supplied with a pre-assembled cover, providing excellent positioning of the ribbon cable before and during the insulation displacement process. fter termination the cover is held in place by each individual contact in addition to two plastic latches at both ends of the connector Max. [.201] Remark: The Micro-MaTch male-on-wire connector is specifically designed to be disengaged from its counterpart by pulling the cable in the appropriate direction. Notes: 1. Connectors are always sideways mounted onto an adhesive tape. 2. Standard packaging quantity is 2500 connectors on a reel with a diameter of 600 mm. 3. t additional charge a special packaging option is available: 250 diameter of 250 mm, packed in a dedicated dispenser box. 6.8 Max. B Max. C Section [.402] Mates with: X X X X X X X X X X X X X X X X No. of Positions Dimensions (mm) Part Numbers B C 2500 Connectors/Reel 250 Connectors/Box

39 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Paddle Board Connector 5.00 [.197] Direct soldering of a ribbon cable onto a PC Board is a very difficult job with the smaller sizes of ribbon cable. If such a permanent cable connection is required, the application can be facilitated by using this connector type. The Paddle Board connector is applied to the ribbon cable with the same application tooling, available for the termination of the Male-on-Wire connector. The solder legs are indented and provide mechanical retention of the connector/cable assembly in the PC Board before and during soldering. This Paddle Board connector version is designed to be soldered onto PC Boards with a nominal thickness of 1.6 mm [] 1.27 [.050] Section - B 2.54 [] 2.54 [] 6.75 [.266] 0.80 [.031] Typical Hole Pattern Not Solder Side Shown 7.10 [.280] 1.27 [.050] Notes: 1. To enable automatic pick & placement, connectors are always packed in embossed tape according EI481 specification. 2. Standard packaging quantity is 900 pcs on a reel with a diameter of 330 mm. 3. Connectors are supplied with or without a feature for vacuum pick & placement. 4. For this connector no additional solder hold down is required. Micro-MaTch Miniature Connector System Paddle Board Connector No mate direct soldering of ribbon cable onto the PC Board No. of Positions Dimensions (mm) Part Numbers B C 2500 Connectors/Reel 250 Connectors/Box

40 METRIC Dimensions are millimeters over inches Micro-MaTch Miniature Connector System Crimp On Snap In (COSI) Connector C 1.27 [.050] 2.54 [] 2.65 [.104] Micro-MaTch Miniature Connector System Crimp On Snap In (COSI) Connector Basic Part Number and Contacts Part Numbers and This crimp version for discrete Wire-to-Board applications is fully compatible with all female connectors of the Micro-MaTch family. Insulation and wire crimp barrel are copies of the well proven MPLIMITE contacts. fter mating with a Micro-MaTch female connector the contacts are fully protected by isolating plastics. Contacts are made of a pre-tinned phosphor bronze. Contacts are supplied in a range for WG and WG. For repair operations an extraction tool is available; Part Number Mates with: X X 6.00 [.236] Ref [.008] 5.10 Max. [.201] 0.82 [.032] 0.70 [.027] 0.40 [.016] B Max. Max Cut Off [.010] Max [.358] Max Max. [.488] 8.65 [.341] Max. Notes: 1. Contacts can be crimped using a mini stripper crimper based applicator. 2. For the contacts on strip the standard packaging quantity is pcs on a reel with a diameter of 600 mm. 3. For repair/service contacts are packaged 750 pcs. Per reel, to be used with handtools. 4. The housings are bulk packed in a box with a packaging quantity varying from 200 to 900 pcs per box. Wire Size Range Insulation Diameter Part Number (mm2) (WG) (mm) Large reel, Small reel, Mates with: X X X X X X X X X X X X X X X X No. of Positions Dimensions (mm) Part Numbers B C 2500 Connectors/Reel 250 Connectors/Box

41 Micro-MaTch Miniature Connector System Specials SMC Connector Part Number This connector type enables a solderless application to the printed circuit board. Contact is made on the surface of the PCB, enabling the use of paperphenol and epoxy boards with both drilled and punched holes. This connector is suitable for both wire-to-board as board-to-board connections. Because this connector is mounted on the solder side, the components of both PCB s in a parallel Board-to-Board application, will be in the same direction. By this, the stacking of two or more PCB s is possible. pplication tooling available on request. Mates with: X X X X X X Locking Latch Part Numbers /338069/ For wire-to-board applications this feature provides an audible click during mating. This feature is available for the standard Micro-MaTch female connectors. Cross reference is made by base part number x x instead of x x, x x instead of x x and x x instead of x x (standard large reel packaging only). Mates with: X X X X X X X X In-board SMD Part Number This connector is only tooled in 20 position ( ) and packaged in embossed tape according to EI481 standards. The connectors are equipped with a feature for vacuum pick & placement. It enables the mounting of a PCB with the solder side direct behind e.g. a display. It is also possible to obtain a parallel BTB application with an extreme low PCB distance of 4.2 mm. Mates with: X X X X X X X X Male SMD Part Number This connector enables the possibility to have a full SMD to SMD board-to-board application. It mates with all Micro-MaTch female connectors, and will be packaged according EI 481 standard. Consult Tyco Electronics for more information. Mates with: X X X X X X X X X X X X X X Micro-MaTch Miniature Connector System Specials 41

42 Micro-MaTch Miniature Connector System pplication Tooling Micro-MaTch Miniature Connector System pplication Tooling Pistol Handgrip Tooling. This is a handtool for terminating Micro-MaTch Male-on-Wire and Paddle Board connectors. Meant for small quantities or repair services. Pistol handgrip and adapter must be ordered separately. Bench Press Tooling Part Number This complete tool includes a Micro-MaTch dedicated tool set mounted on the bench press Standard Pistol Handgrip Part Number This basic tool can be used for Micro-MaTch and other applications. Bench Press Part Number This basic press is a hand operated version. This press can also be obtained in a pneumatically operated version; Part Number Pistol Handgrip dapter Set Part Number This adapter can be used for Micro-MaTch terminations, together with the pistol handgrip. Bench Press Tool Set Part Number This tool set is designed especially for Micro-MaTch. It fits both pneumatically and hand operated press. 42 COSI Hand Tooling Part Number for WG, and Part Number for WG. These dedicated tools can be obtained for services/repair applications. MP-O-LECTRIC G-terminator Model Part Number pplicators for MP-O-LECTRIC G-terminator. Part Number for WG (Part Number ) and Part Number for WG (Part Number ).

43 Micro-MaTch Miniature Connector System pplication Tooling (Continued) Semiautomatic Tooling Part Number This tool can be used for Micro-MaTch connector lead end and for daisy chain assembly applications. Semiautomatic Tooling Part Number for Micro-MaTch connectors only and Part Number for both Micro-MaTch and other ribbon cables. This machine can be used for lead end assemblies. Connector Dispenser Part Number The dispenser accepts the Micro-MaTch standard connectors reels (2500 pcs/reel). It automatically removes the preset connector quantity from the reel and drops it in a separate box. Quantity can easily be programmed by the user. Micro-MaTch Miniature Connector System pplication Tooling 43

44 Micro-MaTch Miniature Connector System Lead ssembly Micro-MaTch Miniature Connector System Lead ssembly and Sample Box It is possible to deliver custom made Micro-MaTch connector lead assemblies, both cable end assemblies and daisy-chain assemblies, in all positions between 4 and 20 in all required cable lengths. ll leads are 100% electrically tested on shortcut and connection before shipment. flexible 7 stranded cable is used for easy assembly. Special cable on request. For order information contact Tyco Electronics. Sample Box Part Number This box includes samples of all connector types within the Micro-MaTch connector family, examples of leads, printed circuit boards and a CD-ROM. The CD-ROM includes an electronic version of this catalogue, an animation of the contact principle and CD files of all connector types. This sample box is an aid in visualizing the variety of applications where Micro-MaTch connector can be implemented. Micro-MaTch Miniature Connector System Sample Box 44

45 PageHead_12_HelvCdBd Universal I/O Pin Connectors (Continued) without Mounting Ears Material and Finish Housing and Cover Flame retardant UL 94V-0 rated thermoplastic, black Contacts Phosphor bronze, [ ] min. tin on termination end, [ ] min. gold on mating end, both over [ ] min. nickel Technical Documents Product Specification pplication Specification Instruction Sheets Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards ssociation, File No. LR 7189 ccessories Strain Relief page 67 Ejector Latch page 63 Military Polarizer page 63 Terminates 26 and 28 WG solid or stranded ribbon cable. See pplication Specification for cable requirements. Related Product Data Mateable Receptacles Novo pages Female Socket Connectors pages Note: ll part numbers are RoHS compliant. R R.330 [8.38] Without Latches Pin Length.240 [6.10] Position No.1 Indicator With Latches B Pins On Centerlines 0.754±.015 [19.15±0.36] No. of Dimensions Part Numbers of Connectors with: Positions B No Latches Short Latches1 Long Latches2 103, , Use short latch versions when mating connectors without strain reliefs are used. 2 Use long latch versions when mating connectors with strain reliefs are used. 3 No slot on end with position No. 1 indicator for 10 and 14-position connectors. 4 No slot for snap-in polarizer on end with position No. 1 indicator for 10 and 14-position connectors [1.27] Centerline Ribbon Cable Connectors Universal I/O Pin Connectors without Mounting Ears

46 Universal I/O Pin Connectors with Slotted Mounting Ears Material and Finish Housing and Cover Flame retardant UL 94V-0 rated thermoplastic, black Contacts Phosphor bronze, [ ] min. tin on termination end, [ ] min. gold on mating end, both over [ ] min. nickel Without Latches With Latches.050 [1.27] Centerline Ribbon Cable Connectors Universal I/O Pin Connectors with Slotted Mounting Ears 46 Technical Documents Product Specification pplication Specification Instruction Sheets Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards ssociation, File No. LR 7189 ccessories Ejector Latch page 63 Military Polarizer page 63 Terminates 26 and 28 WG solid or stranded ribbon cable. See pplication Specification for cable requirements. Related Product Data Mateable Receptacles Novo pages Female Socket Connectors pages Note: ll part numbers are RoHS compliant. R R.330 [8.38] Pin Length.240 [6.10] Position No.1 Indicator B Pins On Centerlines.754 ±.015 [19.15 ± 0.36] No. of Dimensions Part Numbers of Connectors with: Positions B No Latches Short Latches1 Long Latches2 103, , Use short latch versions when mating connectors without strain reliefs are used. 2 Use long latch versions when mating connectors with strain reliefs are used. 3 No slot on end with position No. 1 indicator for 10 and 14-position connectors. 4 No slot for snap-in polarizer on end with position No. 1 indicator for 10 and 14-position connectors.

47 METRIC Dimensions are millimeters over inches EUROLTCH Receptacles, 64-Position (Three-Row Housings, Two Rows Loaded) Housing ssembly with Cover (Preassembled) [3] Row 3.48 [.137] [.413] [.333] 8.46 [.333] Material and Finish Housing and Cover UL 94V-0 rated thermoplastic, black Contacts Phosphor bronze, duplex plated [ ] gold on post/pin mating end, [ ] tin on termination end, with entire contact underplated [ ] nickel. Related Product Data Mateable Pin Connectors Eurocard Type C and Type R Selection Guide 82650, See Catalog Ribbon Cable Part Number or Part Number (64 conductor) pplication Tooling pages Technical Documents Product Specifications EUROLTCH Receptacles DIN IEC Instruction Sheet Recognized under the Component Program of the Underwriters Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards ssociation, File No. LR 7189 R R 6.35 [.250] [3.342] [3.54] [3.730] Row B Row C [.431] [.568] [.731] [3.333] 1.27 [.050] 2.54 [] 2.79 Dia. [.110] Dia. (2 Holes) Contact Receptacle Rows Kit No. Loaded (Preassembled) and C Note: ll part numbers are RoHS compliant. Housing ssembly Cover Terminated [1.27] Centerline Ribbon Cable Connectors EUROLTCH Receptacles 64-Position

48 MP-LTCH Novo Connectors.050 [1.27] Centerline Ribbon Cable Connectors MP-LTCH Novo Connectors Product Facts x [2.54 x 2.54] mating grid for.050 [1.27] pitch ribbon cable Tuning fork contact offers a military approved design, at an economical cost Polarization options include military, center and military, and dual bar Choice of duplex gold plating on contact mating area Insulation displacement contacts for fast, economical mass terminations Contact design provides uniform latching of contacts and housing with connector cover Housing, cover and strain relief made of UL 94V-0 rated thermoplastic material Selected 10 thru 64-position configurations available ccepts wire size range WG [ mm2], solid or stranded Snap-on strain relief and choice of pull loops available One-step termination with Novo tooling Recognized under the Component Program of the Underwriters R Laboratories, Inc. UL File No. E28476 Certified by the Canadian Standards R ssociation, File No. LR 7189 MP-LTCH Novo receptacles offer a dual contact interface with all normal force created by metal-tometal contact. This provides a higher degree of contact reliability. MP-LTCH Novo receptacles feature two rows of contacts on x [2.54 x 2.54] centerlines in select sizes from 10 to 64 positions. Contacts mate with.0252 [0.642] or round posts with.245 [6.22] max. and.175 [4.45] min. lengths. The MP-LTCH Novo tuning fork contact offers a military-approved design, and at a lower cost. Contacts are made of phosphor bronze and are available in a choice of duplex [ ] or [ ] gold in the mating area, and [ ] tin in the termination area, with the entire contact underplated with [ ] nickel. Housings are made of UL 94V-0 thermoplastic material and feature military, military and center, and dual bar polarization. Optional accessories include a snap-on strain relief and pull loops. MP-LTCH Novo receptacles can be terminated to.050 [1.27] pitch ribbon cable by a wide variety of one-step application tooling. ssemblies are packaged in tubes for ease of handling, protection and termination. 48

49 Housing ssembly with Cover (Preassembled) and Strain Relief (Optional) Contacts mate with.025 [0.64] sq. or round pins with.245 [6.22] max. and.175 [4.45] min. lengths. Material and Finish Housing, Cover & Strain Relief UL 94V-0 rated thermoplastic, black Contacts Phosphor bronze, duplex plated (See chart below) Related Product Data Mateable Pin Headers Universal pages Low Profile pages Mateable Universal I/O Pin Connectors pages 45 and 46 ccessories Pull Tabs page 63 Keying Plug page 64 Pull Loops page 66 Strain Relief Dimensional Information page 68 pplication Tooling pages Technical Documents Product Specifications Novo and Novo Stackable Receptacles; Ribbon Cable, PVC Insulated pplication Specification Ribbon Cable Connectors Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. MP-LTCH Novo Receptacles, Military Polarized* x [2.54 x 2.54] Centers.106 [2.69] C Housing ssembly and Cover B Position No. 1 Index Slot.329 [8.36].093 [2.36].629 [15.98] Ref. Housing ssembly.460 [11.68].135 [3.43] [10.72] [11.79] Ref. Ref. Terminated with Cover Cover.240 [6.10] There is no polarization slot on this end of 10- and 14-position receptacles..570 [14.48] Ref..650 [16.51] Ref. Terminated with Cover and Strain Relief No. of Dimensions Contact Strain Relief Receptacle Pos. B C Plating Part No. (Preassembled) Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex [1.27] Centerline Ribbon Cable Connectors MP-LTCH Novo Connectors *These receptacles can be used in applications requiring non-polarization, as well as military polarization [ ] gold or gold flash over palladium-nickel [ ] min. total on post/pin mating end, [ ] tin on termination end, with entire contact underplated [ ] nickel [ ] gold or gold flash over palladium-nickel [ ] min. total on post/pin mating end, [ ] tin on termination end, with entire contact underplated [ ] nickel. Note: These receptacles include a housing assembly and cover (preassembled). Strain reliefs may be purchased separately using the component part nos. listed above. ll part numbers are RoHS compliant. 49

50 .050 [1.27] Centerline Ribbon Cable Connectors MP-LTCH Novo Connectors Housing ssembly with Cover (Preassembled) and Strain Relief (Optional) Contacts mate with.025 [0.64] sq. or round pins with.245 [6.22] max. and.175 [4.45] min. lengths. Material and Finish Housing, Cover & Strain Relief UL 94V-0 rated thermoplastic, black Contacts Phosphor bronze, duplex plated (See chart below) Related Product Data Mateable Pin Headers Universal pages Low Profile pages Mateable Universal I/O Pin Connectors pages 45 and 46 ccessories Pull Tabs page 63 Keying Plug page 64 Pull Loops page 66 Strain Relief page 68 pplication Tooling pages Technical Documents Product Specifications MP-LTCH Novo and MP-LTCH Novo Stackable Receptacles; Ribbon Cable, PVC Insulated pplication Specification Novo Receptacles Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. MP-LTCH Novo Receptacles, Center and Military Polarized* x [2.54 x 2.54] Centers.140 [3.56].106 [2.69] D C.130 [3.30] B Polarization Bar D Housing ssembly and Cover.329 [8.36].629 [15.98] Ref..093 [2.36] Terminated with Cover [10.72] [11.79] Ref. Ref..460 [11.68].135 [3.43] Housing ssembly Cover.240 [6.10].570 [14.48] Ref. Terminated with Cover and Strain Relief There is no polarization slot on this end of 10- and 14-position receptacles. No. of Dimensions Contact Strain Relief Receptacle Pos. B C D Plating Part No. (Preassembled) Position No. 1 Index Slot Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex [16.51] Ref. 50 *These receptacles can be used in applications requiring center polarization [ ] gold or gold flash over palladium-nickel [ ] min. total on post/pin mating end, [ ] tin on termination end, with entire contact underplated [ ] nickel [ ] gold or gold flash over palladium-nickel [ ] min. total on post/pin mating end, [ ] tin on termination end, with entire contact underplated [ ] nickel. Note: These receptacles include a housing assembly and cover (preassembled). Strain reliefs may be purchased separately using the component part nos. listed above. ll part numbers are RoHS compliant.

51 Housing ssembly with Recessed Cover (Preassembled) and Strain Relief (Optional) Material and Finish Housing, Cover & Strain Relief UL 94V-0 rated thermoplastic, black Contacts Phosphor bronze, duplex plated [ ] gold or gold flash over palladium-nickel [ ] min. total on post/pin mating end, [ ] tin on termination end, with entire contact underplated [ ] nickel. Related Product Data Mateable Pin Headers Universal pages Low Profile pages Mateable Universal I/O Pin Connectors pages 45 and 46 ccessories Pull Tabs page 63 Keying Plug page 64 Pull Loops page 66 Strain Relief page 68 pplication Tooling pages Technical Documents Product Specifications MP-LTCH Novo and MP-LTCH Novo Stackable Receptacles; Ribbon Cable, PVC Insulated pplication Specification MP-LTCH Novo Receptacles Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. MP-LTCH Novo Receptacles, Dual Polarized, x [2.54 x 2.54] Centers.140 [3.56].106 [2.69] C.140 [3.56] B.190 [4.83] Housing ssembly and Cover Position No. 1 Index Slot.329 [8.36].629 [15.98] Ref..093 [2.36] No. of Dimensions Strain Relief Receptacle Pos. B C Part No. (Preassembled) Note: ll part numbers are RoHS compliant. Terminated with Cover [10.72] [11.79] Ref. Ref..460 [11.68].135 [3.43] Housing ssembly Cover.240 [6.10].570 [14.48] Ref. Terminated with Cover and Strain Relief.650 [16.51] Ref..050 [1.27] Centerline Ribbon Cable Connectors MP-LTCH Novo Connectors 51

52 METRIC Dimensions are millimeters over inches Female Socket Connectors, x [2.54 x 2.54] Centers, 622 and 636 Series.050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, x [2.54 x 2.54] Centers, 622 and 636 Series Technical Data Color 622 Series, Blue; 636 Series, Black Contact Material 622 Series, Beryllium copper; 636 Series, Phosphor bronze Contact Plating 622 Series, [ ] min. gold on mating end, [ ] tin on termination end, both over [ ] nickel underplate; 636 Series, [ ] min. gold on mating end, [ ] tin on termination end, both over [ ] nickel underplate. Housing Material Glass-filled thermoplastic, UL 94V-0 rated Cable WG solid or stranded, PVC insulated ribbon cable Mateable Connectors Universal and Low Profile Pin Headers pages Universal I/O Ribbon Cable Connectors pages 45 and 46 Polarization Military and center polarized only Recognized under the Component Program of the Underwriters R Laboratories, Inc. UL File No. E60980 Certified by the Canadian Standards R ssociation, File No. LR pplication Tooling Die [T&B# ref.] Handtool [T&B# ref.] Bench Press (Manual) [T&B# ref.] Bench Press Platen [T&B# ref.] Bench Press Base Plate [T&B# ref.] ccessories Strain Relief page 69 Pull Loops page 66 Keying Plug page 64 52

53 Female Socket Connectors, x [2.54 x 2.54] Centers, 622 and 636 Series (Continued) Note: ll part numbers are RoHS compliant. 622 Series No.of Pos Part Numbers Dimensions Connector Connector Only w/ Strain Relief B C Tyco Electronics T&B Tyco Electronics T&B (Reference Only) (Reference Only) LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF Note: Order by Tyco Electronics Part Number only. Original non-rohs compliant T&B number may be determined by dropping the LF suffix. 636 Series No.of Pos. 6 Part Numbers Dimensions Connector Connector Only w/ Strain Relief B C Tyco Electronics T&B Tyco Electronics T&B (Reference Only) (Reference Only) LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF Note: Order by Tyco Electronics Part Number only. Original non-rohs compliant T&B number may be determined by dropping the LF suffix [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, x [2.54 x 2.54] Centers, 622 and 636 Series

54 METRIC Dimensions are millimeters over inches Female Socket Connectors, x [2.54 x 2.54] Centers, 609 Series.050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, x [2.54 x 2.54] Centers, 609 Series Technical Data Color Blue Contact Material Beryllium copper Contact Plating [ ] min. gold on mating end, [ ] tin on termination end, both over [ ] nickel underplate. Housing Material Glass-filled thermoplastic, UL 94V-0 rated Cable WG solid or stranded, PVC insulated ribbon cable Mateable Connectors Universal and Low Profile Pin Headers pages Universal I/O Ribbon Cable Connectors pages 45 and 46 Polarization Military only or military and center polarized Recognized under the Component Program of the Underwriters R Laboratories, Inc. UL File No. E60980 Certified by the Canadian Standards R ssociation, File No. LR pplication Tooling Die [T&B# ref.] Handtool [T&B# ref.] Bench Press (Manual) [T&B# ref.] Bench Press Platen [T&B# ref.] Bench Press Base Plate [T&B# ref.] ccessories Strain Relief page 67 Pull Loops page 66 Keying Plug page 64 Dual Slot IDC Design 3.30 [.130] Optional Center Polarization Standard Socket Connector Without Strain Relief 54 Note: ll part numbers are RoHS compliant.

55 Female Socket Connectors, x [2.54 x 2.54] Centers, 609 Series (Continued) 609 Series, Military Polarized No.of Pos Series, Military and Center Polarized No.of Pos Part Numbers Dimensions Connector Connector Only w/ Strain Relief B C Tyco Electronics T&B Tyco Electronics T&B (Reference Only) (Reference Only) LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF LF Part Numbers Dimensions Connector Connector Only w/ Strain Relief B C Tyco Electronics T&B Tyco Electronics T&B (Reference Only) (Reference Only) MLF MLF MLF MLF MLF MLF MLF MLF Note: Order by Tyco Electronics Part Number only. Original non-rohs compliant T&B number may be determined by dropping the LF suffix. Note: Order by Tyco Electronics Part Number only. Original non-rohs compliant T&B number may be determined by dropping the LF suffix..050 [1.27] Centerline Ribbon Cable Connectors Female Socket Connectors, x [2.54 x 2.54] Centers, 609 Series Note: ll part numbers are RoHS compliant. 55

56 DIP Plugs, x [2.54 x 2.54] Centers, 609 Series.050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, x [2.54 x 2.54] Centers, 609 Series Technical Data Color Blue Contact Material Beryllium copper Contact Plating [ ] tin over [ ] nickel underplate. Contact Design Dual slot, barrel shaped ( tulip ) IDC with solder tail Housing Material Glass-filled thermoplastic, UL 94V-0 rated Cable WG solid or stranded, PVC insulated ribbon cable Mateable Connectors x DIP sockets pplication Tooling Die [T&B# ref.] Handtool [T&B# ref.] Bench Press (Manual) [T&B# ref.] Bench Press Platen [T&B# ref.] Bench Press Base Plate [T&B# ref.].319 Before [8.1] Crimping Dimensions Part Numbers No.of Pos. B Tyco Electronics T&B (Reference Only) Note: Order by Tyco Electronics Part Number only. ll part numbers listed above are found on Tyco Electronics customer drawing ll part numbers are RoHS compliant. B.280 [7.1].008 x.024 [0.2 x 0.6] 56

57 DIP Plugs, x [2.54 x 2.54] Centers, 622 Series Technical Data Color Blue Contact Material Beryllium copper Contact Plating [ ] tin over [ ] nickel underplate. Contact Design Single slot, flat, tuning fork style IDC with solder tail Housing Material Glass-filled thermoplastic, UL 94V-0 rated Cable WG solid or stranded, PVC insulated ribbon cable Mateable Connectors x DIP sockets pplication Tooling Die [T&B# ref.] Handtool [T&B# ref.] Bench Press (Manual) [T&B# ref.] Bench Press Platen [T&B# ref.] Bench Press Base Plate [T&B# ref.] ccessories Strain Relief page (.298) Dimensions Part Numbers No.of Pos. B Tyco Electronics T&B (Reference Only) LF LF LF LF LF LF LF LF LF LF LF LF LF LF Notes: Order by Tyco Electronics Part Number only. ll part numbers are RoHS compliant..050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, x [2.54 x 2.54] Centers, 622 Series 57

58 DIP Plugs, x [2.54 x 2.54] Centers Housing ssembly with Cover (Preassembled).050 [1.27] B C.278 [7.06].050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, x [2.54 x 2.54] Centers 58 Material and Finish Housing and Cover Black thermoplastic, UL 94V-0 rated Contacts Phosphor bronze, plated [ ] min. gold in termination area, [ ] min. tin on solder tails, both over [ ] nickel on entire contact Contact Design Flat, tuning fork style IDC Related Product Data pplication Tooling pages Technical Documents Product Specification DIP Plug Instruction Sheets Instructional material covering operation, setup, maintenance, repair, etc. is included with each machine, tool or die set. If this material is required prior to receiving your tooling, call Tyco Electronics at the numbers listed below for the applicable documents. Mateable Connectors For Connectors without Retention Legs x DIP Sockets C.035 [0.89] Dia. (fter Plating) PCB Layout.050 [1.27] C.013 [0.33] *Height of connector after termination is.253 [6.43] ref..019 [0.48].050 [1.27].156 [3.96].396* [10.06].113 [2.87] No. of Dimensions DIP Plugs With Retention Pos. B C (Preassembled) Legs Notes: ll plug kits include a housing assembly and cover (preassembled). ll part numbers are RoHS compliant.

59 DIP Plugs, x.300 [2.54 x 7.62] Centers Housing ssembly with Cover (Preassembled) Material and Finish Housing and Cover Black thermoplastic, UL 94V-0 rated Contacts Phosphor bronze, plated [ ] nickel underplate on entire contact, [ ] min. gold on termination (IDC) end. See table for leg finish. Contact Design Flat, tuning fork style IDC Related Product Data pplication Tooling pages Technical Documents Product Specification DIP Plug Ribbon Cable Requirements 28 WG stranded or 26, 28 and 30 WG solid wire No. of Dimensions Contact DIP Plugs Pos. B C Plating (Preassembled).300 [7.62] Recommended Mounting Hole Pattern (for [ ] thick pc boards) [ ] gold on leg [ ] gold on leg [ ] tin on leg Note: ll part numbers are RoHS compliant. Duplex Duplex2 Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex Duplex2 Duplex3 Duplex Duplex2 Duplex3.050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, x.300 [2.54 x 7.62] Centers 59

60 DIP Plugs, x.600 [2.54 x 15.24] Centers Housing ssembly with Cover (Preassembled).050 [1.27] Centerline Ribbon Cable Connectors DIP Plugs, x.600 [2.54 x 15.24] Centers Material and Finish Housing and Cover Black thermoplastic, UL 94V-0 rated Contacts Phosphor bronze, plated [ ] nickel underplate on entire contact, [ ] min. gold on termination (IDC) end. See table for leg finish. Contact Design Flat, tuning fork style IDC Related Product Data pplication Tooling pages Technical Documents Product Specification DIP Plug Ribbon Cable Requirements 28 WG stranded or 26, 28 and 30 WG solid wire No. of Dimensions Contact DIP Plugs Pos. B C Plating (Preassembled) [ ] gold on leg Note: ll part numbers are RoHS compliant. Duplex Duplex Duplex Recommended Mounting Hole Pattern (for [ ] thick pc boards) 60

61 4-Row PCB Solder Transition Connectors Technical Data Color Blue Contact Material Beryllium copper Contact Plating [ ] tin over [ ] nickel underplate. Contact Design Dual slot, barrel shaped ( tulip ) IDC with solder tail Housing Material Glass-filled thermoplastic, UL 94V-0 rated Cable WG solid or stranded, PVC insulated ribbon cable pplication Tooling Die [T&B# ref] Handtool [T&B# ref] Bench Press (Manual) [T&B# ref] Bench Press Platen [T&B# ref] Bench Press Base Plate [T&B# ref] 609 Series, Military Polarized Part Numbers No.of Dimensions Tail Length.156 Tail Length Pos. B Tyco Electronics T&B Tyco Electronics T&B (Reference Only) (Reference Only) LF LF LF LF LF LF LF LF LF LF LF Notes: Order by Tyco Electronics Part Number only. ll part numbers listed above are found on Tyco Electronics Customer Drawing ll part numbers are RoHS compliant..050 [1.27] Centerline Ribbon Cable Connectors 4-Row PCB Solder Transition Connectors 61

62 1-Row Horizontal Receptacles 1.25 [.049] Pitch B 1.35 [.053] 1.40 [.055] 2.80 [.110] 3.00 [.118].050 [1.27] Centerline Ribbon Cable Connectors 1-Row Horizontal Receptacles Material and Finish Housing Black PPS, UL 94V-0 rated Contacts Phosphor bronze, post tin plated over nickel underplate 1.25 Fine Pitch (FP) - 1-Row Horizontal Receptacles No. of Dimensions Pos. B C Slot Key Optional Mounting Boss Part Numbers With Mounting Bosses Without Mounting Bosses Tape Bag Tape Bag C 3.40 [.134] Ø 0.80 [.031] 1.35 [.053] 0.70 Min. [.028] 0.50 [.020] PCB Mounting Layout 1.30 [.051] 0.50 [.020] 0.05 [.002] 0.70 Min. [.028] 3.40 [.134] 4.20 [.165] 0.80 [.031]

63 ccessories (Continued) Flexible Pull Tabs Material and Finish Nylon, black Part Number Related Product Data MP-LTCH Novo Connectors pages Ultra T compliant Bus Connectors pages Universal I/O Latches Material and Finish Polyester, black Related Product Data Universal I/O Pin Connectors pages 45 and 46 Latch Removal Tool Part Number [5.99].108±.002 [2.74±0.05] G F C H pproximate Installed Height of Part Number bove Connector No. of Dimensions Positions C H Note: Cannot be used together with a strain relief. Mates to Dimensions Part Receptacles F G Number Without Strain Relief With Strain Relief Note: ll part numbers are RoHS compliant ccessories Military Polarizers Material and Finish Thermoplastic, black.335 [8.51].134 [3.40] Break Line Related Product Data Universal I/O Pin Connectors pages 45 and [8.51].134 [3.40] Throw-way Tab Break Line Part Numbers: (packaged, 50 per bag) (packaged, 1000 per box) The snap-in polarizer provides military polarization. 63

64 ccessories (Continued) Keying Plugs Material and Finish Thermoplastic, see table for color Keying Plug ccessories Key Plug Plug (Installed in Contact) Typical pplication There are ten key plugs on a comb.185 [4.70].500 [12.70] Polarizing Key [6.22].029 [0.58] Receptacle Connector Series Catalog Pages Keying Plug Part Number Style Color 2 mm Rcpt. Connectors 16, Comb Black 609 Series Female , 55 Socket Connectors T&B (Ref.) Single Blue 622 Series Female , 53 Socket Connectors T&B (Ref.) Single Blue 636 Series Female , 53 Socket Connectors T&B (Ref.) Single Blue Order by Tyco Electronics Part Number only. Note: ll part numbers are RoHS compliant. 64

65 ccessories (Continued) Keying Plugs (Continued) Material and Finish Thermoplastic, see table for color Part Number Key Plug (Plugs into Contact) lternate Configuration Keying Plug Part No (10 Keying Plugs per Comb) Receptacle Catalog Keying Plug Connector Series Pages Part Number Style Novo Single Connectors Comb Ultra T Bus Single Connectors Comb Order by Tyco Electronics Part Number only. Note: ll part numbers are RoHS compliant. Color Black Black ccessories 65

66 ccessories (Continued) Pull Loops, Permanent (for Receptacles and Pin Connectors) Material and Finish Natural color PVC, 94-VTM-1 rating (thin material) ccessories Related Product Data Use with: Female Socket Connectors pages Ultra T Compliant Bus Connectors pages mm Receptacle Connectors pages 16 and 17 MP-LTCH Novo Connectors pages Note: This pull loop is installed manually between the cover and strain relief, and cannot be used without strain relief. No. of Positions Female Socket Ultra T Compliant 2 mm MP-LTCH Novo Conns. Bus Connector Rcpt. Conns. Conns , 14, , , 34, Note: ll part numbers are RoHS compliant. Dimension Pull Loop Part No

67 ccessories (Continued) Strain Relief for Universal I/O Pin Connectors Without Mounting Ears Material and Finish Glass-filled polyester, black Related Product Data Universal I/O Pin Connectors page 45 Strain Relief for 609 Series (Tulip Contact) Female Socket Connectors Material and Finish Glass-filled polyester, blue Related Product Data Female Socket Connectors page 54 and [6.10].565 [14.35].240 [6.10].570 [14.46].330 [8.38] Typ. C B.098±.002 [2.49±0.05] 2 Plc..313±.004 [7.95±0.10] Typ. Dimension No. of Dimensions Part Pos. B C Number Standard Version Heavy Duty Version No. of Pos Type Part Number Tyco Electronics T&B (Ref. Only) Standard Heavy Duty HD Standard Heavy Duty HD Standard Heavy Duty HD Standard Heavy Duty HD Standard Standard Heavy Duty HD Standard Heavy Duty HD Standard Heavy Duty HD Standard Heavy Duty HD Standard Heavy Duty HD Note: Heavy duty part numbers are listed on Tyco Electronics customer drawing Standard part numbers are listed on Tyco Electronics customer drawing ll part numbers are RoHS compliant. 67 ccessories

68 ccessories (Continued) ccessories Strain Relief for MP- LTCH Novo and Ultra T Compliant Bus Connectors Material and Finish Glass-filled polyester, black Related Product Data MP-LTCH Novo Connectors pages Ultra T Compliant Bus Connectors pages Strain Relief for 2 mm Receptacle Connectors Material and Finish Glass-filled polyester, black Related Product Data 2 mm Receptacle Connectors pages 16 and [2.69] Ref..276 [7.01] Typ. B.015 [0.38] Rad. Typ..130 [3.30] B Typ..132 [3.35] Typ..186 [4.72].581 [14.76] Ref..240 [6.10].056 Typ. [1.42].030 [0.76] Typ..020 [0.51] Typ..082 Typ. [2.08].201 [5.11] Typ..161 Typ. [4.09].139 Typ. [3.53].040 Typ. [1.02] No. of Dimensions Part Pos. B Number * *Ultra T Compliant Strain Relief is only. No. of Dimensions Part Pos. B Number Note: ll part numbers are RoHS compliant. 68

69 ccessories (Continued) Strain Relief for 622 and 636 Series Female Socket Connectors Material and Finish Glass-filled PBT, see table for color Related Product Data Female Socket Connectors pages 52 and 53 No. of Pos [6.00].555 [14.10] Part Number Dimension C Color Tyco Electronics T&B (Ref. Only).477 Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Blue Black Black Blue Black ccessories Note: These part numbers are listed on Tyco Electronics customer drawing ll part numbers are RoHS compliant. 69

70 Ribbon Cable ssembly Machines (R-CM) pplication Tooling Product Facts Terminates 28 WG [0.08 mm2].050 [1.27] centerline and 30 WG [0.05 mm2].025 [0.64] centerline cable to a variety of connectors utomatic in-process electrical testing tests all circuits for opens, shorts and high-voltage breakdown (up to 1,000 volts for receptacles, 800 volts for card edge connectors and 300 volts for.025 [0.64] centerline connectors); rejects cable assemblies failing any of these tests Operated by a user-friendly, interactive touchscreen or a keyboard on the R-CM 4 Self-diagnostics shut down the machine when a malfunction occurs, pinpoint the malfunction, and identify it on the screen Produced under a Quality Management System certified to ISO 9001 copy of the certificate is available upon request. ISO 9001 Certified The R-CM 4, pictured above, is the newest fully automatic Ribbon Cable ssembly Machine for producing and testing daisy-chained ribbon cable assemblies. Enhancements of this model include the capability to process premanufactured slit-and-twist cable and the ability to produce assemblies with up to 10 connectors. The R-CM 2, 3, and 4 terminate 28 WG [0.08 mm 2 ],.050 [1.27] centerline cable to a variety of connectors. The R-CM 4 will also terminate 30 WG [0.05 mm 2 ].025 [0.64] centerline cable. ll of the R-CM models automatically perform an in-process electrical test of all circuits for opens and shorts. In addition, all models automatically test the assembly for high-voltage breakdown up to 1,000 volts, depending on the machine and connector style. The purpose of this test is to detect gaps that may have been created during assembly that could eventually short out when in use. If an assembly fails any of these tests, the machine will shear the cable off at that point and automatically discard it into an alternate bin. These machines are programmed and operated with an interactive touchscreen that allows operators to access manual, set-up, run, and edit modes through easy-to-follow menu-driven prompts. Self-diagnostics shut down the machine if a malfunction such as misloaded connectors or incorrectly fed cable is detected, pinpoint the malfunction, and identify it on the touchscreen. Models 2 and 3 are available in 120 or 220 VC, 8, 50 or 60 Hz. Model 4 operates at 120 or 220 VC, Hz, single phase, 15. The R-CM 2 and 3 require a minimum air supply of 80 psi [5.52 bar] at 8 scfm [0.0038m 3 /s]. The R-CM 4 requires 80 psi [5.52 bar] at 12 scfm [ m 3 /s]. Need more information? For more information, specifically about tooling, call Tyco Electronics at the numbers listed below. 70

71 Comparison of R-CM 2, R-CM 3 and R-CM 4 Machine Model Part Number* Cable Size Cable ssembly Configurations (Refer to page 73) Production Rates (Refer to page 72) Size Programmable R-CM WG [0.08 mm 2 ],.050 [1.27] centerline Maximum cable length of 48 [1 220] Produces one- to four-connector assemblies with unterminated tail lengths up to 12 [305] Trailing connectors can be oriented up or down Depending on cable lengths, can apply and test up to connectors per hour 108 [2 745] W x 54 [1 370] D x 60 [1 525] H; 750 lb [340 kg] Operated and programmed by a touchscreen Parameters for up to 130 cable assemblies can be retained in memory nother menu displays production totals or a log of the machine events R-CM WG [0.08 mm 2 ],.050 [1.27] centerline Maximum cable length of 105 [2 665] Produces one- or two-connector assemblies with unterminated tail lengths up to 24 [610] Trailing connectors can be oriented up or down Depending on cable lengths, can apply and test up to connectors per hour 48 [1 220] W x 48 [1 220] D x 62 [1 575] H; 630 lb [286 kg] Operated and programmed by a touchscreen Parameters for up to 150 cable assemblies can be retained in memory nother menu displays production totals or a log of the machine events R-CM WG [0.08 mm 2 ],.050 [1.27] centerline and 30 WG [0.05 mm 2 ],.025 [0.64] centerline Maximum cable length of 100 [2 540] Produces one- to 10-connector assemblies with unterminated tail lengths up to 24 [610] Trailing connectors can be oriented up or down utomatically processes and tests assemblies produced with premanufactured slit-and-twist cable Depending on cable lengths, can apply and test up to connectors per hour 68 [1 730] W x 58 [1 475] D x 72 [1 830] H; lb [590 kg] Operated and programmed by a touchscreen or a keyboard Parameters for up to cable assemblies can be retained in memory pplication Tooling Testing utomatically stops after each or three consecutive assemblies are rejected, as programmed by the operator utomatically stops when either a consecutive number of assemblies or a percentage of the batch run are rejected, as programmed by the operator utomatically stops each time a malfunction is detected Changeover Requires an average of 25 minutes, depending on assembly size Requires an average of 15 minutes, depending on assembly size Requires an average of 20 minutes to 1 hour, depending on assembly size and type *Note: Machine may require accessories. Before ordering, contact Tyco Electronics at the numbers listed below. 71

72 Typical Production Rates (ssemblies/hour) pplication Tooling Machine Connectors Length Model Per ssembly 4 [100] 8 [205] 24 [160] 48 [1 220] 100 [2 540] R-CM R-CM R-CM Note: ctual production rates may vary depending on the cable assembly configuration. vailable Tooling Tooling for Number of Positions Connectors R-CM 2 R-CM 3 R-CM 4 ıı MP-LTCH Ultra Novo Receptacles 40 MPLIMITE.050 Series Connectors 68 Plugs 68 and 80 (Lead and Trail Modules) MPLIMITE HDF-20 D-Sub. 15, 25, 37 9, 15, 25, 37 Receptacles 68 and 80 (Lead Module Only) x DIP Plugs One End Only, One End Only, vailable in future Card Edge Connectors* (10 64 vailable in future) MP-LTCH Novo Receptacles* mm Receptacles Universal I/O Pin Connectors One End Only, Trail Module Only * Supplied with the R-CM 2 and R-CM 3 only. ı Reel fed version. ıı Order Connector Specific Tooling Packages / Feed Shear Tooling separately. Products pplied Note: Call Tyco Electronics at the numbers listed below for part numbers or availability. MPLIMITE HDF-20 D-Sub. Plugs MPLIMITE HDF-20 D-Sub. Receptacles x DIP Plugs Card Edge Connectors MP-LTCH Novo Receptacles 2 mm Receptacles Universal I/O Pin Connectors Pre-manufactured Slit-and-Twist Cable (R-CM 4 only) 72 Note: For more product information, call Tyco Electronics at the numbers listed below.

73 Cable ssembly Configurations R-CM to 8 [70 to 205] end-to-end 2.70 to 48 [70 to 1 220] end-to-end R-CM 3 0 to 8 [0 to 205] 0 to 24 [0 to 610] 1.50 Min. [35 Min.] center-to-center 1.74 to 105 [45 to 2 665] end-to-end 1.74 to 105 [45 to 2 665] end-to-end 1.74 to 105 [45 to 2 665] end-to-end R-CM 4 0 to 24 [0 to 610] pplication Tooling 1.60 to 100 [40 to 2 540] center-to-end 1.60 to 100 [40 to 2 540] center-to-center 0 to 24 [0 to 610] 1.60 Min Min. 3 Min. [40 Min.] [30 Min.] [75 Min.] center-to-center center-to-center center-to-center 73

74 pplication Tooling pplication Tooling Manual rbor Frame ssembly, Part No Bench frame for applying a variety of IDC connectors, including MPMODU MT and CHMP. Features adjustable ram and handle, and a slide base. Tooling is mounted to the ram and into the tracks of the base plate. Pneumatic uto-cycle Unit, Part No Hand Tool Kit Part No Terminating kit for.050 [1.27] centerline ribbon cable with 28 or 26 WG [0.08 or 0.15 mm 2 ] stranded or solid, or 30 WG [0.05 mm 2 ] solid conductors. Includes commercial grade hand tool with ratchet control for complete termination cycle, base assembly, bench-mount, tooling sets for standard and Novo receptacles, card edge connectors and D-Sub HDF low-profile connectors, and a carrying case. Basically an air-powered version of Manual rbor Frame ssembly Features adjustable ram and cycle time, and automatic cycling when the lower assembly is slid into the frame to the rear of the base plate. Includes a guard around the frame opening. Tooling Instruction Sheets Manual rbor Frame ssembly Pneumatic uto-cycle ssembly Hand Tool Kit for Connector-Specific Kits Pneumatic Foot Pedal Unit Part No Foot pedal indicates cycle features adjustable ram and cycle time. 74

75 Low Profile Headers Product Facts vailable in selected positions 10 thru 60 Flame retardant, thermoplastic housings, 94V-0 rated Vertical and right-angle versions available in double row configurations vailable in.025 [0.64] square drawn wire posts Wash out clearance for flux removal Mates with Ribbon Cable Connectors vailable with and without eject latches vailable with and without kinked soldertails for PCB retention Headers are recognized under the Component Program of Underwriters Laboratories Inc. R File No. E28476 Headers are certified by Canadian Standards ssociation, R File No. LR 7189 Low profile IDC headers are recognized under the Component Program of Underwriters Laboratories Inc. R File No. E60980, Vol. 5 Performance Characteristics Electrical Insulation Resistance 5,000 megohms minimum initial Dielectric Withstanding Voltage 1,000 V rms at sea level Current 1 ampere maximum per contact Operating Voltage 250 VC Environmental Operating Temperature -65 C to +105 C Technical Documents Product Specifications Low Profile Headers 75

76 Low Profile Pin Headers, Center and Dual Polarized, x [2.54 x 2.54] Centerlines Low Profile Headers Vertical PCB Mount.025 [0.64] Square Post (Mating End) Material and Finish Housing Glass-filled nylon, UL 94V-0 rated, black Posts Brass, plated as follows: Plating Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Plating B Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MPMODU Wire-pplied Receptacles MPMODU Board Mount Receptacles Short Point Wire-pplied Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages [3.30].045 [1.14].165 [4.19].025 ±.001 [0.64 ± 0.03] Typ..360 [9.14] B Pin 1 Pin [1.04].388 [9.86].185 ±.010 [4.70 ± 0.25].185 [4.70] Typ. Typ [ ].035 ±.003 [0.89 ± 0.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion [ 0.38 ] [6.10].025 ±.001 [0.64 ± 0.03].120 ±.015 [3.05 ± 0.38] No. of Dimensions Post Plating/Part Nos. Pos. B Plating Plating B [20.32].400 [10.16] [25.40].600 [15.24] [27.94].700 [17.78] [33.02].900 [22.86] [38.10] 1 [27.94] [40.64] [30.48] [50.80] [40.64] [58.42] [48.26] [71.12] [60.96] [83.82] [73.66] Note: ll part numbers are RoHS compliant. 76

77 Low Profile Pin Headers, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Right-ngle PCB Mount.025 [0.64] Square Post (Mating End) Material and Finish Housing Glass-filled nylon, UL 94V-0 rated, black Posts Brass, plated as follows: Plating Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Plating B Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MPMODU Wire-pplied Receptacles Short Point Wire-pplied Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages ±.010 [4.69 ± 0.25] Typ..165 [4.19] B [ ].185 Typ. [4.69] [ 0.25 ] Position No.1 Indicator Typ..035 ±.003 [0.89 ± 0.08] Dia. Typ..130 Typ. [3.31] Recommended PC Board Hole Layout For Manual Insertion.388 [9.86].025 ±.001 [0.64 ± 0.03] Pin 1 Typ. Pin [9.14].025 ±.001 [.635 ± 0.03] Typ..123 [3.12].240 [6.09] No. of Dimensions Post Plating/Part Nos. Pos. B Plating Plating B [20.32].400 [10.16] [25.40].600 [15.24] [27.94].700 [17.78] [33.02].900 [22.86] [40.64] [30.48] [50.80] [40.64] [58.42] [48.26] [71.12] [60.96] [83.82] [73.66] Note: ll part numbers are RoHS compliant [ ] Low Profile Headers 77

78 Low Profile Pin Headers, Center and Dual Polarized, x [2.54 x 2.54] Centerlines & Kinked Solder Tails for PCB Retention Low Profile Headers Vertical PCB Mount.025 [0.64] Square Post (Mating End) with Board Retention Feature.130 [3.30].045 [1.14] B [ ].165 [4.19] Pin [ 0.64 ] 0.51 Material and Finish Housing Glass-filled PP, UL 94V-0 rated, black Posts Brass, plated as follows: Plating Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MPMODU Wire-pplied Receptacles MPMODU Board Mount Receptacles Short Point Wire-pplied Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages ±.001 [0.64±0.03] Typ..041 [1.04].388 [9.86].185 [4.69] 2 Plcs..185 [4.69] 2 Plcs. Typ..040 ±.003 [1.02 ± 0.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion Pin [9.14].240 [6.10].025 ±.001 [0.64 ± 0.03].120 ±.015 [3.05 ± 0.38] No. of Dimensions Post Plating Pos. B Part Nos [20.32].400 [10.16] [25.40].600 [15.24] [27.94].700 [17.78] [33.02].900 [22.86] [38.10] 1 [27.94] [40.64] [30.48] [50.80] [40.64] [58.42] [48.26] [71.12] [60.96] [83.82] [73.66] Note: ll part numbers are RoHS compliant. 78

79 Low Profile Pin Headers, Center and Dual Polarized, x [2.54 x 2.54] Centerlines & Kinked Solder Tails for PCB Retention (Continued) Right-ngle PCB Mount.025 [0.64] Square Post (Mating End) with Board Retention Feature Position No.1 Indicator.388 [9.86].165 [4.19].025±.001 [0.64±0.03] Typ. Low Profile Headers Material and Finish Housing Glass-filled PP, UL 94V-0 rated, black Posts Brass, plated as follows: Plating Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MPMODU Wire-pplied Receptacles Short Point Wire-pplied Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages [9.14].185 [4.69] 2 Plcs [ -0.25] B Plcs. [4.69] Plcs. [1.14].130 Typ. [3.30] Typ..040±.003 [1.02±0.08] Dia. Typ. Recommended PC Board Hole Layout For Manual Insertion.025±.001 [.635±0.03] Typ. Pin 1 Pin [ 0.64 ] [3.12].240 [6.09] [ ] No. of Dimensions Post Plating Pos. B Part Nos [20.32].400 [10.16] [25.40].600 [15.24] [27.94].700 [17.78] [33.02].900 [22.86] [38.10] 1 [27.94] [50.80] [40.64] [58.42] [48.26] [71.12] [60.96] Note: ll part numbers are RoHS compliant. 79

80 IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches, Military and Center Polarized, x [2.54 x 2.54] Centerlines IDC Low Profile Headers Vertical PCB Mount.025 [0.64] Square Post (Mating End) Material and Finish Housing Glass-filled PBT, UL 94V-0 rated, black Posts Brass or phosphor bronze, plated as follows: Plating Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages ±.012 [22.56 ± 0.30] For Long Eject Latch.728 ±.012 [18.49 ± 0.30] For Short Eject Latch Pin [9.19] Position #1 Indicator.404 ±.006 [10.26 ± 0.15] Pin 1 Part Numbers No. of Dimensions Pin Header with Short Latches Pin Header with Long Latches Pos. B (Mates with Receptacles (Mates with Receptacles without Strain Relief) with Strain Relief) Note: ll part numbers are RoHS compliant. B.025 ±.001 [0.64 ± 0.03] Ø.035 ±.003 [0.89 ± 0.08] Recommended PC Board Layout.254 ±.006 [6.45 ± 0.15] Latch Housing.025 ±.001 [0.64 ± 0.03] Post Ø.031 Max. [0.79].102 ±.015 [2.59 ± 0.38] Latching Height.575 Long [14.61].427 [10.85] Short.237 ±.007 [6.02 ± 0.18] 80

81 IDC Low Profile Ejection Style Pin Headers with Die Cast Ejection Latches, Military and Center Polarized, x [2.54 x 2.54] Centerlines (Continued) Right-ngle PCB Mount.025 [0.64] Square Post (Mating End) Material and Finish Housing Glass-filled PBT, UL 94V-0 rated, black Posts Brass or phosphor bronze, plated as follows: Plating Duplex plated, gold flash over palladium-nickel, [ ] min. total on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel or [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages ±.012 [22.56 ± 0.30] For Long Eject Latch Pin [9.19] Position #1 Indicator.728 ±.012 [18.49 ± 0.30].404 ±.006 For Short [10.26 ± 0.15] Eject Latch Pin 1 Part Numbers No. of Dimensions Pin Header with Short Latches Pin Header with Long Latches Pos. B (Mates with Receptacles (Mates with Receptacles without Strain Relief) with Strain Relief) Note: ll part numbers are RoHS compliant. B U U.025 ±.001 [0.64 ± 0.03] Ø.035 ±.003 [0.89 ± 0.08] Latch Recommended PC Board Layout Housing.254 ±.006 [6.45 ± 0.15].025 ±.001 [0.64 ± 0.03] Post.102 ±.010 [2.59 ± 0.25] Section U-U.237 ±.007 [6.02 ± 0.18] Latching Height.575 Long [14.61].427 [10.85] Short.030 [0.76] Ø.031 Max. [0.79] IDC Low Profile Headers 81

82 IDC Low Profile Ejection Style Pin Headers, Center Polarized, x [2.54 x 2.54] Centerlines IDC Low Profile Headers 82 Vertical PCB Mount.025 [0.64] Square Post (Mating End) Material and Finish Housing and Eject Latches PBT, UL 94V-0 rated, blue Posts Phosphor bronze, plated as follows: Plating Duplex plated, [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages [0.33] [ ] Eject Latches Not Shown in Top and Side View for Clarity.350 [8.89].350 [8.89].013 [0.33] Position #1 Indicator.013 [0.33] Pin 2 Position #1 Indicator.025 ±.001 [0.63 ± 0.03] Part Numbers Dim. C No. of Dimensions (Soldertail Pin Header Pin Header with Short Latches Pin Header with Long Latches Length) Pos. B without (Mates with Receptacles (Mates with Receptacles Latches without Strain Relief) with Strain Relief) [31.75].400 [10.16] [36.83].600 [15.24] [39.37].700 [17.78] [44.45].900 [22.86] [49.53] 1 [27.94] [52.07] [30.48] [57.15] [35.56] [62.23] [40.64] [69.85] [48.26] [82.55] [60.96] [95.25] [73.66] [31.75].400 [10.16] [36.83].600 [15.24] [39.37].700 [17.78] [44.45].900 [22.86] [49.53] 1 [27.94] [52.07] [30.48] [62.23] [40.64] [69.85] [48.26] [82.55] [60.96] Note: ll part numbers are RoHS compliant. B Pin 1 U U With Latches.025 ±.001 [0.63 ± 0.03] U U Without Latches Ø.035 ±.003 [0.89 ± 0.08] Recommended PC Board Layout [ ].025 ±.001 [0.63 ± 0.03].826 ±.020 Long [20.98 ± 0.51].665 ±.020 [16.89 ± 0.51] Short.576 ±.006 Long [14.62 ± 0.15].419 ±.006 [10.64 ± 0.15] Short Ø.031 [0.79] Max. Section U-U.240 ±.010 [6.10 ± 0.25] C ±.015 [± 0.38]

83 IDC Low Profile Ejection Style Pin Headers, Center Polarized, x [2.54 x 2.54] Centerlines (Continued) Right-ngle PCB Mount.025 [0.64] Square Post (Mating End) Material and Finish Housing and Eject Latches PBT, UL 94V-0 rated, blue Posts Phosphor bronze, plated as follows: Plating Duplex plated, [ ] min. gold on mating surfaces, [ ] min. tin on solder area, with entire post underplated [ ] min. nickel Related Product Data Electrical Characteristics page 75 Mateable Connectors MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 and 636 Series pages [0.33] [ ] Eject Latches Not Shown in Top and Side View for Clarity.350 [8.89].350 [8.89].013 [0.33] Position #1 Indicator.013 [0.33] Pin 2 Position #1 Indicator.025 ±.001 [0.63 ± 0.03] Part Numbers Dim. C No. of Dimensions (Soldertail Pin Header with Long Latches Length) Pos. B (Mates with Receptacles with Strain Relief) [39.37].700 [17.78] [49.53] 1 [27.94] [52.07] [30.48] [57.15] [35.56] [95.25] [73.66] [31.75].400 [10.16] [62.23] [40.64] [69.85] [48.26] Note: ll part numbers are RoHS compliant. B Pin ±.001 [0.63 ± 0.03] U U With Latches U U Without Latches Ø.035 ±.003 [0.89 ± 0.08] Recommended PC Board Layout [ ].826 ±.020 [20.98 ± 0.51] Long.665 ±.020 [16.89 ± 0.51] Short.025 ±.001 [0.63 ± 0.03].576 ±.006 Long.240 ±.010 [14.62 ± 0.15] [6.10 ± 0.25].419 ±.006 [10.64 ± 0.15] Short C ±.015 [± 0.38] Section U-U.030 [0.76] Ø.031 [0.79] Max. IDC Low Profile Headers 83

84 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines Vertical PCB Mount.025 [0.64] Sq. Posts (Mating End).336 [8.53].253 [6.43].315 [8.00] Pin [3.81].165 [4.19].190 [4.83].240 [6.10] Ø.025 [0.64] Military, Center and Dual Polarized, Vertical Mount Universal Ejection Style Pin Headers Pin Header with Latches Pin Header without Latches Material and Finish Housing & Latches Black PBT or nylon, UL 94V-0 rated Contacts Brass; duplex plated (See chart, page 85) Related Product Data Mateable Receptacles pages ccessories Snap-In Polarizer page 63 Technical Documents Product Specifications Pin Headers Pin [13.94] Position No.1 Indicator.025 [0.64].150 [3.81] D No. of Dimensions Positions B C D E F Notes: 1. Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown. Notes: 2. Pin headers in 10-position size have only slot for dual polarization, located as shown. Notes: 3. For information regarding latch/pin header applications and for ordering latches separately, refer to page 96. B C.050 [1.27].195 [4.95].025 [0.64].096 [2.44] Dia. 2 Plc..106 [2.74].107 [2.72].289 [7.34].110 [2.79] or.155 [3.94] Solder Tail 84

85 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Vertical PCB Mount.025 [0.64] Sq. Posts (Mating End) (Continued) Contact Soldertail No. of Finish Length Positions (Plating Code) Pin Header w/ Pin Header w/ Pin Header Short Latches Long Latches without (Mates with MP-LTCH (Mates with MP-LTCH Latches Receptacles without Receptacles with Strain Relief) Strain Relief) B B B B B B B B B B B B B B B B B B B B B B B B Plating Code Gold flash over palladium-nickel plate, [ ] min. total on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min nickel underplate or [ ] min. gold on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min. nickel underplate. Plating Code B Gold flash over palladium-nickel plate, [ ] min. total on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min nickel underplate or [ ] min. gold on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min. nickel underplate. Note: ll part numbers are RoHS compliant. Military, Center and Dual Polarized, Vertical Mount Universal Ejection Style Pin Headers 85

86 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Military, Center and Dual Polarized, Vertical Mount Universal Ejection Style Pin Headers Mounting Information 4-24 self-tapping screws and 2-56 bolts and nuts are available for mounting straight-thru pin headers of pc boards. Typical applications and part nos. for ordering this hardware are presented below. Note: 2-56 bolts and nuts may be used to mount pin headers with and without latches. If latches are to be used, the bolts must be positioned in the pin header before the latches are installed..060 [1.52] Position No [8.89] Recommended Mounting Hole Pattern For Vertical PCB Mount Headers PC board thicknesses are :.062 [1.57] for.110 [2.79] long posts,.125 [3.18] for.155 [3.94] long posts Self-Tapping Screw (2 Req d.) Pin Header Mounting using 4-24 Self-Tapping Screws: Part No (for.062 [1.57] Thick PC Board) Part No (for.093 [2.36] Thick PC Board) Part No (for.125 [3.18] Thick PC Board).035 [0.89] Dia. E F.106 [2.88] Dia. (For Nut & Bolt hardware).116 [2.95] Dia. (For Self-Tapping Screw hardware) Latch (See Note at left.) 2-56 Bolt & Nut (2 Each Req d.).256 [6.50] Pin Header Mounting with 2-56 Bolts and Nuts: Part No (Bolt Only) Kit No (Bolt and Nut, 2 Each per Kit) 86 Note: ll part numbers are RoHS compliant.

87 Universal Ejection Style Pin Headers with CTION PIN Contacts, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines Vertical PCB Mount.025 [0.64] Sq. Posts (Mating End).253 [6.43].150 [3.81] Pin [4.19].190 [4.83].336 [8.53].315 [8.00] Pin Header without Latches Material and Finish Housing Black PBT or nylon, UL 94V-0 rated Contacts Copper alloy; duplex plated (See chart, page 88) Related Product Data Mateable Receptacles pages ccessories Snap-In Polarizer page 63 Technical Documents Product Specifications Pin Headers with CTION PIN Contacts pplication Specification MP-LTCH Universal Headers with CTION PIN Contacts.025 [0.64] Pin 1 No. of Dimensions Positions B C D E Notes: 1. Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown. Notes: 2. Pin headers in 10-position size have only slot for dual polarization, located as shown. Notes: 3. For information regarding latch/pin header applications and for ordering latches separately, refer to page [6.10].107 [2.72].289 [7.34] Position No. 1 Indicator.150 [3.81] B C.050 [1.27].030 [0.76].174 [4.42] or.610 Tail [15.49] Length.025 [0.64].025 [0.64].549 [13.9] 87 Military, Center and Dual Polarized Universal Ejection Style Pin Headers with CTION PIN Contacts

88 Universal Ejection Style Pin Headers with CTION PIN Contacts, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Military, Center and Dual Polarized Universal Ejection Style Pin Headers with CTION PIN Contacts 88 Mounting Information 4-24 self-tapping screws and 2-56 bolts and nuts are available for mounting straight-thru pin headers of pc boards. Typical applications and part nos. for ordering this hardware are presented on page 86. Tail Length Contact Pin Header No. of Positions Finish (without (Plating Code) Latches) [4.42] 26 B [15.49] 26 B Plating Code B Gold flash over palladium-nickel plate, [ ] min. total on the mating surfaces, [ ] min. tin plate on the tails, over [ ] min nickel underplate or [ ] min. gold on the mating surfaces, [ ] min. tin plate on the tails, over [ ] min. nickel underplate..060 [1.52] Position No. 1 Note: ll part numbers are RoHS compliant. Recommended Mounting Hole Pattern For Vertical PCB Mount Header With CTION PIN Contacts *For.080 [2.03] min. thick PCB refer to pplication Specification for hole size and finish recommendations..106 [2.69] Dia..350 [8.89] D E *

89 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines Right-ngle PCB Mount.025 [0.64] Sq. Posts (Mating End).253 [6.43] Pin [3.81].165 [4.19].190 [4.83] [8.53] [8.00] Pin Header with Latches Pin Header without Latches Material and Finish Housing & Latches Black PBT or nylon, UL 94V-0 rated Contacts Brass; duplex plated (See chart, page 90) Related Product Data Mateable Receptacles pages ccessories Snap-In Polarizer page 63 Technical Documents Product Specifications Pin Headers Pin 1 Pos. No. 1 Indicator.549 [13.94] No. of Dimensions Positions B C D E F Notes: 1. Pin headers in 10- and 14-position sizes have only one slot for snap-in polarizer (military polarization), located as shown. Notes: 2. Pin headers in 10-position size have only slot for dual polarization, located as shown..150 [3.81].240 [6.10] [0.64] [2.72] B C.025 [0.64] D.050 [1.27].025 [0.64] Dia..289 [7.34].195 [4.95].096 [2.44].108 [2.74].038 [0.97] [2.79] or [3.94] Typ. Typ. Solder Tail 89 Military, Center and Dual Polarized, Right-ngle Universal Ejection Style Pin Headers

90 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Military, Center and Dual Polarized, Right-ngle Universal Ejection Style Pin Headers Right-ngle PCB Mount.025 [0.64] Sq. Posts (Mating End) (Continued) Contact Soldertail No. of Finish Length Positions (Plating Code) Pin Header w/ Pin Header w/ Pin Header Short Latches Long Latches without (Mates with (Mates with Latches Receptacles without Receptacles with Strain Relief) Strain Relief) B B B B B B B B B B B B B B B B B B B B B B B B Plating Code Gold flash over palladium-nickel plate, [ ] min. total on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min nickel underplate or [ ] min. gold on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min. nickel underplate. Plating Code B Gold flash over palladium-nickel plate, [ ] min. total on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min nickel underplate or [ ] min. gold on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min. nickel underplate. Note: ll part numbers are RoHS compliant. 90

91 Universal Ejection Style Pin Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Mounting Information No mounting hardware is supplied by Tyco Electronics. E F.106 [2.69] Dia..029 [0.74] Position No [5.84].035 [0.89] Dia. Typ. Recommended Mounting Hole Pattern For Right-ngle PCB Mount Headers PC board thicknesses are :.062 [1.57] for.110 [2.79] long posts,.125 [3.18] for.155 [3.94] long posts. Military, Center and Dual Polarized, Right-ngle Universal Ejection Style Pin Headers 91

92 Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines Vertical PCB Mount.025 [0.64] Sq. Posts (without latches) Pin 2 Dia. 2 Holes E.150 [3.81] C.050 [1.27] Military, Center and Dual Polarized Universal Ejection Style Pinless Headers Pinless Header Material and Finish Housing Black PBT or nylon, UL 94V-0 rated Related Product Data Mateable Receptacles pages ccessories Snap-In Polarizer page 63 Technical Documents Product Specifications Pin Headers Pin 1 Position No.1 Indicator.096 [2.44] Dia. 2 Holes B.549 [13.9] No. of Dimensions Pinless Header Part Nos. Pos. B C E Press-Fit Clearance-Fit Notes: and 14-position pinless headers have only one slot for snap-in polarizer (military polarization) position pinless headers have only one slot for dual polarization. 3. For information regarding latch/pin header applications and for ordering latches separately, refer to page 96. ll part numbers are RoHS compliant..315 [8.00] 92

93 Universal Ejection Style Pinless Headers, Military, Center and Dual Polarized, x [2.54 x 2.54] Centerlines (Continued) Installation of Press-Fit Pinless Headers Insertion Instructions: 1. Place pinless header over preinstalled posts so that post tips start into header cavities. 2. With bottom of pc board supported, place steel block over header. Steel block must be wider and longer than header so that it covers all four sides of the header. However, for headers with latches pre-assembled, the steel block must not interfere with the latches. 3. pply an even, centered force on steel block until header bottoms on pc board. If posts are longer than.545 [13.84], they may be forced against the steel block before the header is fully seated. In this situation, extreme caution must be taken so that posts are not damaged or pushed out of the pc board. FORCE Insertion Force: 60 lb. [267 N] max. Retention Force: 20 lb. [89 N] min. Steel Block (Centered over Header) Pinless Header.025 Sq. Posts [0.64] Preinstalled in PC Board PC Board Tyco Electronics recommends the use of a typical manual frame assembly for insertion of pinless headers. The frame assembly and steel block are not supplied by Tyco Electronics. FORCE.529 [13.44] Military, Center and Dual Polarized Universal Ejection Style Pinless Headers 93

94 Universal Ejection Style Pin Headers with PCT Housing, x [2.54 x 2.54] Centerlines,.025 [0.64] Sq. Posts (Mating End) x [2.54 x 2.54],.025 [0.64] Sq. Posts (Mating End) Universal Ejection Style Pin Headers with PCT Housing Vertical PCB Mount Right-ngle PCB Mount Material and Finish Housing Red PCT, UL 94V-0 rated Contacts Brass; Gold flash over palladium-nickel plate, [ ] min. total on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min. nickel underplate or [ ] min. gold on the mating surfaces, [ ] min. tin plate on the soldertails, over [ ] min. nickel underplate Related Product Data Mateable Receptacles pages ccessories Snap-In Polarizer page 63 Technical Documents Product Specifications Pin Headers.549 [13.94].250 [6.35].549 [13.94].200 [5.08].200 [5.08].195 [4.95] Vertical.250 [6.35].050 [1.27].050 [1.27] C B D C.025 [0.64] B D.150 [3.81].025 [0.64].150 [3.81].195 [4.95] Position No.1 Indicator.040 [1.02].110 [2.79] [8.00] [8.64].165 [4.19] [3.28] [3.81].350 Pin 2 [8.89] E Position No.1 Indicator Pin 1 Pin [1.02].110 Dia. [2.79] 2 Plc..096 [2.44].240 [6.10].240 [6.10].289 [7.34].289 [7.34].110 [2.79] Ø.025 [0.64] [8.00] [8.64].110 [2.79].165 [4.19].350 [8.89].150 [3.81] E Pin [3.28].151 [3.84] Ø.025 [0.64] Right-ngle 94

95 Universal Ejection Style Pin Headers with PCT Housing, x [2.54 x 2.54] Centerlines,.025 [0.64] Sq. Posts (Mating End) (Continued) Part Numbers No. of Dimensions Vertical Right-ngle Pos. B C D E Pin Header Pin Header (without (without Latches) Latches) Note: ll part numbers are RoHS compliant. C L of Holes.060 [1.52] C L of Holes Typ. B Position No [1.78] Typ..035 [0.89] fter Plating Recommended PC Board Mounting Pattern for Vertical Header.106 Dia. [2.69] Dia. Typ..090 [2.29].110 [2.79] of Stencil Pattern x [2.54 x 2.54],.025 [0.64] Sq. Posts (Mating End) Universal Ejection Style Pin Headers with PCT Housing C L of Holes Typ. Position No. 1 C.070 [1.78] Typ..106 Dia. [2.69] Dia. Typ..090 [2.29].029 [.736] C L of Holes.475 Max.* [12.07] Board Edge.035 [0.89] fter Plating.110 [2.79] of Stencil Pattern Recommended Pc Board Mounting Pattern for Right-ngle Header *Max. distance from edge of PC board for daisy chain applications 95

96 Latches for Ejection Style Universal Pin Headers and Pinless Headers Latches for Ejection Style Pin Headers and Pinless Headers Latches for use with MP-LTCH Novo Receptacles and Female Socket Connectors, 609, 622 & 636 Series Material Red PCT, UL 94V-0 Rated.576 [14.63] Long Latch Part No (See Figure 1).416 [10.57] Short Latch Part No (See Figure 2) Material Black thermoplastic, UL 94V-0 Rated.576 [14.63] Latch/Pin Header pplications [27.31] [27.72] Figure 1 Use Long Latch for MP-LTCH Novo Receptacles with Strain Relief & Female Socket Connectors with Strain Relief.895 [22.73].175 [4.45] Figure 2 Use Short Latch for MP-LTCH Novo Receptacles without Strain Relief & Female Socket Connectors without Strain Relief Material Black thermoplastic, UL 94V-0 Rated.561 [14.25].475 [12.07].265 [6.73] Long Latch Part No (See Figure 1).185 [4.70] Ref..691 [17.55] Ref [10.57] Short Latch Part No (See Figure 2) Note: ll part numbers are RoHS compliant..140 ±.008 [3.56 ± 0.20] Special Long Latch Part No for MPMODU Mod IV Housing with Center Polarization Key