Coin Acceptors, Inc. Installation Instructions for the 4.3 Touch Screen Display
|
|
- Garey Jordan
- 5 years ago
- Views:
Transcription
1 Coin Acceptors, Inc. Installation Instructions for the 4.3 Touch Screen Display Kit # and DN3800 and DN5800 Publication
2 Hand Drill Utility Knife Step Ladder 5/8 Drill Bit Tools Required Wire Cutters #2 Phillips Screwdriver 7/16 Wrench or Socket SWIPE-Service Tech Card 11/32 Nut driver 8 Cable Ties 9/16 and 7/8 Wrench Kit - VCE Iris Media Kit For DN3800 and DN5800 Machines NOTE: is the same kit but without the bill acceptor/card reader unit. 2
3 1 Mounting Location For The Touch Screen Display NOTE: Make sure the vendor is operational by vending a beverage before beginning. Remove power from vendor. On the DN3800 and DN5800 Glass Front, you may need to replace the Service Door Top Bezel assembly with one designed for a card reader. Top Bezel with Card Reader Opening Coca-Cola Top Bezel P/N Bev Max 3 Coke Red Bezel CCP P/N Bev Max 3 Dasani Black Bezel CCP P/N Bev Max 4 Coke Red Bezel CCP P/N Bev Max 4 Dasani Black Bezel CCP P/N Installing The 4.3 Touch Screen Display Remove the door display security plate (4 screws) located above the bill acceptor mounting hole. Note: Keep these four (4) screws for If the Service Door Top Bezel Assembly is not designed for a card reader, you will need to change the Top Bezel. To change the Top Bezel, remove the (6) Phillips screws that attach the Top Bezel to the Service Door and install a new Top Bezel with Card Reader hole. Install the Display mounting plate using the (4) screws removed from The mounting plate rectangular hole must be towards the top. 3
4 Step 4. While holding the display in the top bezel, attach the display to the mounting plate with (4) Phillips screws. Step 5. Plug in the display ribbon cable as shown, extending the cable upward. The ribbon cable is keyed, so it will only fit one way. 3 Install the Vantage Bill Acceptor Connect the Vantage MDB harness P/N to the bill acceptor before mounting to the vendor. Remove the bill box to make the bill acceptor installation easier. Attach the Vantage bill acceptor/card reader to the vendor using 4 nuts. 4
5 4 Install the IRIS Media Telemeter Find a suitable place to mount the yellow IRIS Media Telemeter, within reach of all the harnesses. The box has 4 magnets built in for attaching to any metal surface. Neatly route the ribbon cable from the LCD Display to the IRIS Media Telemeter. Plug the cable into the backside of the IRIS Media Telemeter. Step 4. Use a cable tie to hold excess ribbon cable out of the way. 5 Install The Antenna Find a suitable metal location for mounting the antenna on the outside of the vendor. Be sure there is enough antenna wire to reach the IRIS Media Telemeter before drilling a hole! Drill a 5\8 hole in the top of the cabinet service compartment to attach the antenna on the outside of the vendor. Try to keep the Antenna away from any electronics such as transformers, ballasts or fluorescent lighting. Remove the antenna nut and install the gasket to the bottom of the antenna as shown. 5
6 Feed the antenna wire through the drilled hole. Dixie Narco Glass-Front vendors require a barrel Nut Extension, p/n Use a 7/8 wrench to tighten the barrel nut. Step 4. When routing the antenna wire, keep it away from the fluorescent light ballast. Do Not coil the excess antenna wire. Excess antenna wire must not be bundled. 6 Perform Final Connections DEX Be sure to unplug and remove any external DEX jack(s) from the vending machine. Plug the white 16-pin DEX harness connector to the yellow IRIS Media Telemeter. Plug the other end of this harness into the controller board s DEX jack. 6
7 MDB Plug the 6-pin IRIS Media Telemeter MDB harness ( ) to the MDB connection coming from the vendor s controller board. Next, plug the MDB harness from the bill acceptor to the coin changer MDB plug and the other end goes into the IRIS Media Telemeter MDB plug. Plug the 12-pin white connector to the IRIS Media Telemeter labeled MDB. CARD READER Plug the white 20-pin connector from the Card Reader bezel harness to the IRIS Media Telemeter. The box is labeled Reader. Step 4. ANTENNA Screw the Antenna harness to the Antenna jack located on the bottom left side of the IRIS Media Telemeter. Note: Be sure the antenna connector is Finger Tightened Only! Step 5. Use cable ties to neatly dress the added wires. Be sure to keep all wires away from moving parts and the bill acceptor box. See example. 7
8 Revision: Publication
Greenlite Cashless In-Field Hardware Installation Instructions
Greenlite Cashless In-Field Hardware Installation Instructions Page 1 Your Greenlite Cashless field install package includes, for each vending machine: One box containing a Greenlite Device, Antenna, and
More informationInstructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only)
Instructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only) **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit Kit Contents PART NAME
More informationRoyal RVV-500 (B) Retrofit Kit
Optipay BV/RC/CC into a Non-Fascia Vending Machine This document contains information for installing and configuring the JCM Optipay DBV-01 Bill Validator, RC-10 Bill Recycler and A-66 Coin Changer into
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More informationInstructions to Install Retrofit Kit 6/7000 Machine
Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationCREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual
CREDIT CARD READER for ROWE CD100I CD100J Jukeboxes Installation Instructions Manual Part No. This page intentionally left blank Table of Contents INTRODUCTION...5 Tools Required...5 Credit Card Reader
More informationNavigator Telemetry Quick Start Guide For use with or higher software
Introduction Navigator Telemetry Quick Start Guide This document explains the installation method, and assignment process to permit acceptance of credit card payments, and to enable telemetry when using
More informationKit# KOV ModBox IR REMOTE CONTROL KIT
ModBox Installation Instructions Kit# KOV-106-000-07 ModBox IR REMOTE CONTROL KIT INTRODUCTION: This kit adds IR Volume and Cancel Control to ModBox Jukeboxes. TOOLS REQUIRED: 1/4" nut driver, Philips
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationHow To Install: C4000 EMV Upgrade Kit
How To Install: C4000 EMV Upgrade Kit IMPORTANT: Before proceeding with installation please verify you have the current card reader bezel in the kit. Correct bezel will have a small eject pin hole below
More informationHGR-2488 Prism Installation Instructions
HGR-2488 Prism Installation Instructions These installation instructions are applicable to the following models: TASCAM 2488 MK1 (original model) TASCAM 2488 MK II TASCAM 2488 NEO Page 1 of 8 Important
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationUSBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version
USBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version 2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla Street Chatsworth, CA 91311
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationNintendo DS Lite Rear Display Bezel Replacement
Nintendo DS Lite Rear Display Bezel Replacement Replacement of the Nintendo DS Lite rear display bezel. Written By: Matt Newsom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Replace the rear
More informationInstalling a Power over Ethernet injector
Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationPracticeWire. Field Support: Page 1
PracticeWire Field Support: 1-877-233-9114 Page 1 Table of Contents Required Tools Page 3 Software Hardware 1) Admin Login.... Page 3 2) Checking AT&T signal strength Page 3 3) Port test.. Page 4 1) Cradlepoint
More informationSony NEX-7 Screen Replacement
Sony NEX-7 Screen Replacement If your camera's screen is broken or non functioning, this guide will show you how you can replace the screen. Written By: Jay Miley ifixit CC BY-NC-SA www.ifixit.com Page
More informationIMPORTANT AS YOU REMOVE THE CONNECTORS LABEL THE CONNECTOR WITH THE NAME OF PLUG WITH THE SHARPIE
TOOLS REQUIRED : small flat head screwdriver no wider than ⅛ or 3mm wide, phillips head screwdriver, 3mm allen wrench, self tapping screws #6 x ½, ¼ hex head driver, electric drill, wire cutters, fine
More informationINSTALLATION INSTRUCTIONS
2015 F-150 8 MyTouch factory display 360º Vision System (Kit # AVMS-3618) DUE TO THE COMPLEXITY OF THIS KIT PROFESSIONAL INSTALLATION IS REQUIRED CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING -Must
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationHow To Install: G2500 EMV Upgrade Kit
How To Install: G2500 EMV Upgrade Kit Tools Needed: Phillips Screw Driver Wire Cutter - Begin by verifying the contents of the kit Kit includes: - EMV Card reader (with ground and data cable) - Card reader
More informationTOYOTA YARIS H/B PREMIUM AUDIO Preparation
Preparation Part Number: PT296-47141 (Extension Box) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module w/bt cable 2 1 Wire harness 3 4 Screws (M5x8) Hardware Bag Contents Item # Quantity
More informationNov. 07, 2013 p. 5 - changed the B axis unit value to from Changed by Randy per Frank s request.
Correction notes Nov. 07, 2013 p. 5 - changed the B axis unit value to 45.1389 from 40.0000. Changed by Randy per Frank s request. Jan. 22, 2018 p. 5 - changed the B axis unit value and corresponding picture
More informationInstallation Instructions. Rock-Ola Ecast B75B Motherboard Upgrade Kit Kit #
Installation Instructions Rock-Ola Ecast B75B Motherboard Upgrade Kit Kit #26683901 This kit will not support the Ecast Rock-Ola COIM Board. If your Rock-Ola core computer has the Ecast Rock-Ola COIM board
More informationWaveRider Installation
WaveRider Installation Single Washer Serial Mode (MDC & Quantum) PREP FOR COIN CARD ONLY OPERATION Coin Box Mount 2115 Chapman Road, Suite 159, Chattanooga TN 37421 800.332.4835 Laundry Machine Types This
More informationUpgrading LVDS Cables Instruction Sheet
Upgrading LVDS Cables Instruction Sheet INTRODUCTION Use the following instructions to replace the LVDS cables in CP2000-M/MR projectors. The new cables are slightly longer in length and allow for better
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationInstallation Instructions
Installation Instructions Ecast EQ to AMI hardware conversion KIT #26683701 This kit is for use in Ecast EQ jukeboxes. Tools Required #2 Phillips screw driver, #1 Phillips screw driver, Small flat blade
More informationC764i Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
C764i Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 3 Obtaining Service... 3 Unpacking the Equipment... 3 Important
More informationINSTALLATION MANUAL. LO SIDE BOX ADD-ON KIT For driver or passenger side configurations TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK
TRUCK STORAGE SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL LO SIDE BOX ADD-ON KIT For driver or passenger side configurations Model: QDKSBDO1 -or- QDKSBP01 Part No. 24-0327 Rev. A ECN 5430 ATTENTION:
More information7" Touch Screen Display
7" Touch Screen Display Installation Guide Contents Minimum Requirements...1 Select a Location...1 Initial Setup...2 Unboxing...2 Installation...3 Prepare the Panel...3 Install the Mounting Plate...3 Mount
More informationDMD Extender. Application Note 1 Sega Large Screen LCD Replacement. V0.1 October 2013 Copyright 2013 Dr Pinball
DMD Extender Application Note 1 Sega Large Screen LCD Replacement V0.1 October 2013 Copyright 2013 Dr Pinball Important This document is a guide to installing an LCD panel to replace a plasma display in
More informationGolf Control Panel Conversion Instructions
Golf Control Panel Conversion Instructions Document Part #: 040-0079-01 This document describes the steps for upgrading the control panel on an old golf cabinet for use with an EA SPRTS PGA TUR Golf Conversion
More informationKit Instructions. Camera (NTSC) and Telephone Handset Upgrade K034 Issue A
Kit Instructions Camera (NTSC) and Telephone Handset Upgrade 7705-K034 Issue A The product described in this book is a licensed product of NCR Corporation. NCR is a registered trademark of NCR Corporation.
More informationParts List: Part # Tools List: Instructions:
Parts List: Part # 1 pair of Dayton Audio B652s 300-652 1 Dayton Audio DTA-2 amplifier 300-385 1 MP3 module 320-350 1 7805 +5 VDC voltage regulator 7805 1 12 VDC 2A power supply 129-077 1 2.1 mm panel
More informationYamaha DX7 LCD Installation Guide
Table of Contents Required Tools/ Getting Started... p. 2 Installation... p.3-11 Opening the DX7... p. 3 Locating and Removing the LCD Bracket... p. 4 Removing the LCD Bezel Cover... p. 5 Removing the
More informationMacBook Core 2 Duo Clutch Cover
MacBook Core 2 Duo Clutch Cover Replacement Replace the clutch cover on your MacBook Core 2 Duo. Written By: Ben Eisenman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Replace the curved
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More informationRédigé par: Matthew Newsom
Replacement of the Nintendo DS Lite microphone. Rédigé par: Matthew Newsom ifixit CC BY-NC-SA fr.ifixit.com Page 1 de 18 INTRODUCTION Can't make Bowser breath fire by blowing in the microphone anymore?
More informationINTRODUCTION TO MECHANICAL ASSEMBLY (DVD-46C)
This test consists of twenty multiple-choice questions. All questions are from the video: Introduction to Mechanical Assembly. Each question has only one most correct answer. Circle the letter corresponding
More informationLANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS
LANCER / LANCER EVOLUTION (2008 ) REAR VIEW CAMERA MZ380462EX INSTALLATION AND HANDLING INSTRUCTIONS Navigation (MMCS) unit Camera Thank you for purchasing the Mitsubishi Genuine Accessory. To install
More information641G-001A PRINTER KIT INSTRUCTIONS
641G-001A PRINTER KIT INSTRUCTIONS P-11351 5/05/98 SAFETY The installer of this equipment must assume the responsibility for his own safety, and that of those working around him. He must also make sure
More informationipad 4 - Disassemble Guide
ipad 4 - Disassemble Guide TTT-9001 Plastic Triangle Opening Tool TTT-9002 Metal Opening Tool TTT-9007 Small Phillips Screwdriver TTT-9010 Plastic Opening Tools TTT-9013 Spudger Heat Gun / Blow Dryer This
More informationCycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 4 Obtaining Service... 4 Unpacking the
More informationTile Plow Installation O Connell
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Tile Plow Kit O Connell System 4100471 1 Hex head cap screw 3/8-16 x 3 2002003-38300
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationWritten By: Andrew Bookholt
iphone 3GS Power Button Replacement Use this guide to replace the plastic power button cover on your iphone 3GS. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More informationPrisma II Chassis 56-Port Upgrade Technical Bulletin
Prisma II Chassis 56-Port Upgrade Technical Bulletin Overview Audience Introduction This technical bulletin applies to all cable system operators and technicians who use the Prisma II Chassis configured
More informationInstallation Instructions. Ecast View B75B Motherboard Upgrade Kit Kit #
Ecast View B75B Motherboard Upgrade Kit Kit #26683801 This kit will not support the Ecast View COIM Board. If your View core computer has the Ecast View COIM board installed you must order the AMI Hardware
More informationForeseesons Monitor Installation Instructions
Foreseesons Monitor Installation Instructions Visit the Merit Entertainment Web site http://www.meritind.com PM0626-04 Table of Contents Parts List... p. 1 Cabinet Identification... p. 1 Cabinets with
More informationTim Hortons EI30 Ethernet Interface Circuit Board
Tim Hortons EI30 Ethernet Interface Circuit Board INSTALLATION INSTRUCTIONS Replacing the Precidia Unit with the HME EI30 Thank you for purchasing the EI30 Ethernet Interface. The EI30 enables the System
More informationCoin Manager CN MDB Installation Guide-Canada. Set Up Screen Features (Continued) GENERAL INFORMATION
Set Up Screen Features (Continued) Fig.18 Coin Manager 7512 CN MDB Installation Guide-Canada GENERAL INFORMATION To View errors - Press the yellow mode button (highlighted View ) to gain access. Use the
More informationLANCNC FTP Data Server for CNC Controls Machine Mount instructions
LANCNC FTP Data Server for CNC Controls Machine Mount instructions 2008-2016 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla Street Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationInstalling 6 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing 6 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Overview...5 Installing the
More informationAF Upgrade Instructions
8602 8631AF Upgrade Instructions Bering Technology, Inc. 1400 Dell Avenue, Suite B Campbell CA 95008-6620 (408) 364-6500 FAX: (408) 364-6501 Email: info@bering.com Contents 15-18631-81 Revision D This
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CASSETTE/MP3 (EX) 2006 PILOT All 30488 Issue Date SEP 2005 Player Attachment Kit (sold separately) : P/N 08B06-S9V-100A Cassette Player
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS CB RADIO P/N 08E83-MKC-A00 GL1800/D/DA Honda Dealer: Please give a copy of these instructions to your customer. MII 16426 Issue Date January
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS AUDIO UNIT P/N 08A70-MJN-A00 CTX1300/D MII 14925 Issue Date April 2014 PARTS LIST (11) (8) (2) TOOLS AND SUPPLIES REQUIRED Socket (10 mm)
More informationLightning Stitch Assembly
ABM International, Inc. 1 1.0: Parts List Lightning stitch motor and drive assembly (Qty. 1) Lightning stitch piggy backed controller board assembly (Qty. 1) Touchscreen (Qty. 1) 2 9-pin Serial cable (Qty.
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationBL-FLOWSTN-P FlowStation Module Installation Guide
Introduction Baseline s FlowStation is available as an add-on module that is installed inside a pedestal enclosure with a BaseStation 3200 irrigation controller. The FlowStation module comes with a 5-port
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationCommBox Interactive Table User Manual 1.0. Revision: 5
CommBox Interactive Table User Manual 1.0 Revision: 5 Table of Contents 1 Introduction 3 1.1 Table Assembly Components 3 1.2 Accessories 3 2 Table Assembly Procedure 4 2.1 Step 1 4 2.2 Step 2 5 2.3 Step
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationTreadmill Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Treadmill Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 Before You Begin... 4 Obtaining Service... 4 Unpacking the Equipment... 4 Important
More informationMacBook Core 2 Duo Display Replacement
MacBook Core 2 Duo Display Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION Change out the entire display assembly, including the inverter, Airport antennas, hinges
More informationMemory Expansion for DriveLogix Controller
Installation Instructions Memory Expansion for rivelogix ontroller!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work
More informationA-dec 586 Ceiling Monitor Mount
Installation Guide A-dec 586 Ceiling Monitor Mount Recommended Tools 7/16" wrench Socket set and ratchet with 6" extension Phillips head and standard screwdrivers Diagonal cutters Level 3/8" drill with
More informationPowerView Model PV1000. Hardware Installation Manual Section 78
PowerView Model PV1000 Hardware Installation Manual 00-02-0599 07-19-07 Section 78 In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationReplacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638
Replacing the Galaxy II CRT Monitor with a Flat Screen Monitor Kit # 42638 This kit contains detailed instructions on removing a Galaxy II Daewoo monitor and replacing it with a 19 wide flat screen monitor.
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationOLPC XO-4 Touch Touchpad Controller Replacement
OLPC XO-4 Touch Touchpad Controller Replacement This guide will walk through replacing a touchpad. Written By: Theodore Tsanakas ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION Use this guide
More informationKRONOS INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TABLE OF CONTENTS ENCLOSURE AND DONGLE ASSEMBLY 1 LIGHTED ENCLOSURES 2-10 2 SLIM ENCLOSURE 11-17 3 WIRED-ETHERNET DONGLE 18-25 4 REAR-OFFSET MOUNT 26-33 5 SIDE-MOUNT 34-41 6 SURFACE
More informationHOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE
HOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE Important: Please read this document in its entirety before removing the Parker VFD drive and installing the Yaskawa V1000 drive.
More informationCutter Option Installation Instructions
This kit includes the parts and documentation necessary to install the cutter option on the Zebra XiII, XiIII, and XiIIIPlus-Series printers. NOTE: The Cutter Option is not available for the 96XiIII. Adding
More informationUpgrade Instructions. P/N Revision A. October Printer Terminal Holder * *
Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers
More informationINSTALL INSTRUCTIONS PT-VIDEO-1, 2, 3, or 4 PT-VIDEO-MDVR PRISONER TRANSPORTATION VIDEO SYSTEM
INSTALL INSTRUCTIONS PT-VIDEO-1, 2, 3, or 4 PT-VIDEO-MDVR PRISONER TRANSPORTATION VIDEO SYSTEM TOOLS REQUIRED: Powered Drills (3/8 & ½ ) 4 ½ Hole Saw or Jig Saw Drill bit Set Wire Stripping Tool Wire Crimping
More informationAdapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout
Installation Instructions Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Catalog Numbers 2711-NR5T, 2711P-RAT12E2 Topic Page About This Publication 1 Important User Information 2 About
More informationMIDI IN Installation Guide for the EMU Drumulator
MIDI IN Installation Guide for the EMU Drumulator 1 WARNING: This installation process is the user s responsibility and shall be followed at their own risk! To complete this modification the procedure
More informationWritten By: Matthew Newsom
Nintendo DS Lite Motherboard Replacement Replacement of Nintendo DS Lite motherboard. Written By: Matthew Newsom ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION So you spilled water on your
More informationReplacement Keyswitch Assembly
Installation Instructions Replacement Keyswitch Assembly (Catalog No. 2711E-NKSW1) Applicable Terminals Use this replacement keyswitch with PanelView Terminals 2711-KA1, -KC1, -TA1, -TC1, -TA4, -TC4 and
More informationFRU Installation Notes Virtuo Monitor Glass Replacement
January 2016 900975-001 Rev 00 FRU Installation Notes Virtuo Monitor Glass Replacement Purpose How to replace the touch screen glass on a Virtuo This document is for these components or categories Expected
More informationInstalling TEAC CD-ROM Drives
D I G I T A L Installing TEAC CD-ROM Drives S O U N D Date: May 12, 2000 (updated) Document # TN-E211 We have used only two manufacturers of CD-ROM drives: Toshiba and TEAC. This procedure is to be used
More informationPDC / ECIS. Display Update update with conversion kit Display Update. Contents. General information. Important notes.
US Toll Free: 800.BODE.TEC BodeTechnicalServices.com Display Update PDC / ECIS Display Update update with conversion kit 535268 Contents General information Important notes Requirements Conversion instructions
More informationInstallation Manual. for Mobile Link Adapter for Liquid-cooled Generators
Installation Manual for Mobile Link Adapter for Liquid-cooled Generators for use with Mobile Link Unit Reference all appropriate documentation. This manual should remain with the Mobile Link unit. Table
More informationMicroscope with original illuminator. Microscope with Nanodyne replacement illuminator.
Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationGeneral Applicability All Scion xb models, including 10 Year Anniversary Edition.
Preparation Part Number: PT296-00140, PT296-00142 or PT296-00151 (Extension Box w/aha) Kit Contents Item # Quantity Req. Description 1 1 Extension Module w/bt cable 2 1 DA/Ext Harness 3 1 GPS Antenna kit
More informationCopy Machine Reader. Installation and Setup Guide
Copy Machine Reader Installation and Setup Guide CONTENTS 1 COPY MACHINE READER INSTALLATION 1 Overview 1 Reader Specifications 3 CR1120/CR1122 INSTALLATION 3 Copier Interface 3 AC Electrical 3 Communications
More informationPrinter Radio Interface Kit PD41, PD42, PF2i, PF4i, PM4i, PX4i, PX6i. Installation Instructions
Printer 802.11 Radio Interface Kit PD41, PD42, PF2i, PF4i, PM4i, PX4i, PX6i Installation Instructions Intermec Technologies Corporation Worldwide Headquarters 6001 36th Ave.W. Everett, WA 98203 U.S.A.
More informationLG Vu CU920 LCD Screen Replacement
LG Vu CU920 LCD Screen Replacement This guide shows how to remove a cracked or broken LCD screen on the LG Vu CU920. Written By: Alan Reeve ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION Use
More information