PRIMERGY CX122 S1 Server

Transcription

1 Operating Manual - English PRIMERGY CX122 S1 Server Operating Manual Edition November 2010

2 Comments Suggestions Corrections The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs. Feel free to send us your comments by to Certified documentation according to DIN EN ISO 9001:2008 To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001:2008. cognitas. Gesellschaft für Technik-Dokumentation mbh Copyright and Trademarks Copyright 2010 Fujitsu Technology Solutions GmbH. All rights reserved. Delivery subject to availability; right of technical modifications reserved. All hardware and software names used are trademarks of their respective manufacturers. The contents of this manual may be revised without prior notice. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. No part of this manual may be reproduced in any form without the prior written permission of Fujitsu. Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of Microsoft Corporation in the USA and other countries. Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the USA and other countries.

3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product. Keep this manual and the manual "Safety Notes and Regulations" in a safe place for easy reference while using this product. Radio interference This product is a "Class A" ITE (Information Technology Equipment). In a domestic environment this product may cause radio interference, in which case the user may be required to take appropriate measures. VCCI-A Aluminum electrolytic capacitors The aluminum electrolytic capacitors used in the product's printed circuit board assemblies and in the mouse and keyboard are limited-life components. Use of these components beyond their operating life may result in electrolyte leakage or depletion, potentially causing emission of foul odor or smoke. As a guideline, in a normal office environment (25 C) operating life is not expected to be reached within the maintenance support period (5 years). However, operating life may be reached more quickly if, for example, the product is used in a hot environment. The customer shall bear the cost of replacing replaceable components which have exceeded their operating life. Note that these are only guidelines, and do not constitute a guarantee of trouble-free operation during the maintenance support period. High safety use This product has been designed and manufactured for general uses such as general office use, personal use, domestic use and normal industrial use. It has not been designed or manufactured for uses which demand an extremely high level of safety and carry a direct and serious risk to life or body if such safety cannot be ensured. CX122 S1 Operating Manual

4 These uses include control of nuclear reactions in nuclear power plants, automatic airplane flight control, air traffic control, traffic control in mass transport systems, medical devices for life support, and missile guidance control in weapons systems (hereafter, "high safety use"). Customers should not use this product for high safety use unless measures are in place for ensuring the level of safety demanded of such use. Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning. To prevent a momentary voltage drop, use of an AC uninterruptible power supply is recommended. (This notice follows the guidelines of Voltage Dip Immunity of Personal Computer issued by JEITA, the Japan Electronics and Information Technology Industries Association.) Technology controlled by the Foreign Exchange and Foreign Trade Control Law of Japan Documents produced by Fujitsu may contain technology controlled by the Foreign Exchange and Foreign Trade Control Law of Japan. Documents which contain such technology should not be exported from Japan or transferred to non-residents of Japan without first obtaining authorization in accordance with the above law. Harmonic Current Standards This product conforms to harmonic current standard JIS C Only for the Japanese market: About SATA hard disk drives The SATA version of this server supports hard disk drives with SATA / BC-SATA storage interfaces. Please note that the usage and operation conditions differ depending on the type of hard disk drive used. Please refer to the following internet address for further information on the usage and operation conditions of each available type of hard disk drive: Operating Manual CX122 S1

5 Contents 1 Preface Concept and target groups for this manual Documentation overview Features Notational conventions Technical data Installation steps, overview Important information Information for ensuring electromagnetic compatibility Safety instructions CE conformity FCC Class A Compliance Statement Environmental protection Hardware installation Installation Procedure Installing / replacing a PRIMERGY CX122 S1 server Removing a PRIMERGY CX122 S1 server Installing a PRIMERGY CX122 S1 server Connecting devices and cables Connecting devices Connecting / disconnecting cables Network cabling Starting up and operation CX122 S1 Operating Manual

6 5.1 LAN indicators Front panel Controls Indicators Switching the server on and off Switching the server on Switching the server off Configuring the server Operating system installation Index Operating Manual CX122 S1

7 1 Preface The new PRIMERGY CX1000 rack server system is tailored to the needs of internet service providers: The cost and energy efficient architecture provides the highest server density per square meter with maximum reliability. Thanks to the centralized innovative cooling approach and front side connection panels PRIMERGY CX1000 system units can be set up 'back to back' requiring less datacenter floor space. PRIMERGY CX122 S1 server nodes for use with the CX1000 rack infrastructure are all-purpose servers with top dual processor performance for cloud computing data centers. Despite the compact form factor, each PRIMERGY CX122 S1 server offers eighteen DDR3 memory slots for up to 144 GB of RAM and up to two 2.5-inch SATA hard disk drives. 1.1 Concept and target groups for this manual This manual will familiarize you with the controls and indicators of your PRIMERGY CX122 S1 server nodes. The operating manual is aimed at those responsible for installing the hardware and ensuring the proper operation of the system. To understand the concepts described in this manual, you will need to be familiar with the fields of hardware and data transmission. CX122 S1 Operating Manual 7

8 Documentation overview 1.2 Documentation overview More information on your PRIMERGY CX122 S1 can be found in the following documents: "Quick Start Software - Quick Installation Guide" DVD booklet (only included with the ServerView Suite as a printed copy) except for the Japanese market "Safety notes and regulations" manual " 安全上のご注意 " for the Japanese market "Warranty" manual " 保証書 " for the Japanese market "ServerView Suite Local Service Concept - LSC" manual "Returning used devices" manual and "Service Desk" leaflet " サポート & サービス " for the Japanese market "PRIMERGY CX122 S1 Server Operating Manual" "System Board D2899 for PRIMERGY CX122 S1 Technical Manual" Information of CX1000 can be found in the following documents: PRIMERGY CX1000 S1 System Unit PRIMERGY CX120 S1 Server Operating Manual I PRIMERGY manuals are available in PDF format on the ServerView Suite DVD 2. The ServerView Suite DVD 2 is part of the ServerView Suite supplied with every server. If you no longer have the ServerView Suite DVDs, you can obtain the relevant current versions using the order number U15000-C289 (the order number for the Japanese market: please refer to the configurator of the server The PDF files of the manuals can also be downloaded free of charge from the Internet. The overview page showing the online documentation available on the Internet can be found using the URL (for EMEA market): The PRIMERGY server documentation can be accessed using the Industry standard servers navigation option. For the Japanese market please use the URL: 8 Operating Manual CX122 S1

9 Features Further sources of information: PRIMERGY Abbreviations and Glossary on the ServerView Suite DVD 2 Operating system documentation 1.3 Features High Capacity Up to 38 PRIMERGY CX122 S1 server nodes can be installed into a PRIMERGY CX1000 system units. Ventilation and Power Supply The centralized PRIMERGY CX1000 chimney ventilation concept allows operation of up to 38 passively cooled server nodes with only two large radial fans installed on top of the rack cabinet. The design purpose is the most efficient cooling of the server nodes using the minimum of electrical energy to move air. The fans, mounted at the top of the rack, do not cool the servers directly, but exhaust air from a low pressure chamber which subsequently draws the air through the servers. The control of the fans is an autonomous function (see "Rack Management Unit (RMU)" operating manual) and serves to maintain a constant under-pressure in this chamber. System Board The hardware and BIOS features of the PRIMERGY CX122 S1 system board are described in the technical manual for the system board D2899 and the BIOS manual. Expansion Cards Each PRIMERGY CX122 S1 server node provides one riser slot (PCIe Gen2 x16 ). Hard Disk Drives The PRIMERGY CX122 S1 server node can be ordered with up to two 2.5-inch SATA hard disk drives. CX122 S1 Operating Manual 9

10 Notational conventions Serviceability and Support Operating and maintaining your PRIMERGY CX1000 S1 rack server system is easy: CX122 S1 server nodes are lightweight, mounted on slide rails with front accessible network ports. The highly efficient power supply connects cordlessly to the power distribution unit in the rack. The fanless node cooling concept allows for virtually wear-free operation. 1.4 Notational conventions The following notational conventions are used in this manual: Text in italics "Quotation marks" Ê V CAUTION! I indicates commands or menu items. indicate names of chapters and terms that are being emphasized. describes activities that must be performed in the order shown. pay particular attention to texts marked with this symbol. Failure to observe this warning may endanger your life, destroy the system or lead to the loss of data. indicates additional information, notes and tips. 10 Operating Manual CX122 S1

11 Technical data 1.5 Technical data Electrical data Rated voltage range 200 V V Rated frequency 50 Hz - 60 Hz Max. rated current 200 V V / 2.0 A Rated current X5500 series CPUs 200 V V / 1.8 A Rated current E5500 series CPUs 200 V V / 1.0 A Rated current L5500 series CPUs 200 V V / 0.8 A Rated current idle mode 200 V V / 0.3 A (depending on configuration / application) Effective power (X / E / L series CPUs) Apparent power (X / E / L series CPUs) Heat dissipation (X / E / L series CPUs) Main power fuse EMEA Main power fuse NORAM Protection class 286 W / 192 W / 185 W (depending on configuration / application) 302 VA / 206 VA / 200 VA (depending on configuration / application) 1029 KJ/h (975 btu/h) 691 KJ/h (654 btu/h) 666 KJ/h (631 btu/h) 16 A 20 A I CX122 S1 Operating Manual 11

12 Technical data Compliance with regulations and standards Product safety and ergonomics International IEC /2 Europe EN /2 EN USA / Canada UL/CSA /2 Taiwan CNS USA / Canada GB 4943 Electromagnetic compatibility International AS / NZS CISPR22 Class A Europe CE Class A EN EN EN EN ETSI EN USA / Canada FCC Class A ICES-003 Class A Taiwan CNS Class A China CCC (GB 9245 / GB 17625) Japan VCCI Class A CE marking to EU directives Low Voltage Directive: 2006/95/EC Electromagnetic compatibility: 2004/108/EC Mechanical values Width Depth Height Weight 483 mm (front panel) 454 mm 42 mm / 1 HU 6.5 kg (depending on the configuration) 12 Operating Manual CX122 S1

13 Technical data Ventilation clearance Front Rear min. 200 mm min. 200 mm Ambient conditions Environment class 3K2 Environment class 2K2 DIN IEC 721 section 3-3 DIN IEC 721 section 3-2 Ambient temperature 10 C - 35 C (DIN IEC ) class 3K2, ETSI Class 3.1 Temperature: Operation (3K2) 10 C C Transport (2K2) -25 C C Humidity 10%... 85% RH non-condensing Condensation during operation must be avoided! Conditions of use Air quality The system complies with regulation Class 3S2 according to DIN EN (for product class B). Noise level Sound power level L WAd (ISO 9296) Sound pressure level at adjacent position L pam (ISO 9296) SATA sub-system (no active cooling) SATA sub-system (no active cooling) CX122 S1 Operating Manual 13

14 Technical data 14 Operating Manual CX122 S1

15 2 Installation steps, overview This chapter contains an overview of the steps you need to carry out in order to set up your server. Links take you to sections where you can find more detailed information about the respective steps: Ê Ê Ê Ê First of all, it is essential that you familiarize yourself with the safety information in chapter "Important information" on page 17. Your PRIMERGY CX1000 system has been unpacked and set up by a Fujitsu service technician. Make sure that the accompanying documentation (see "Documentation overview" on page 8) is complete. Print out the required PDF files, if necessary. Familiarize yourself with the controls and indicators on the front of the CX122 S1 server nodes, (see section "LAN indicators" on page 39 and section "Front panel" on page 41). Configure the server and install the desired operating system and applications (see section "Configuring the server" on page 45). CX122 S1 Operating Manual 15

16 16 Operating Manual CX122 S1

17 3 Important information In this chapter you will find essential information regarding safety when working on your server. 3.1 Information for ensuring electromagnetic compatibility All data and signal cables must have sufficient shielding The LAN cabling must be conform with the requirements EN and EN /2. Use of unshielded or badly shielded cables may led to increased emission of interference and/ore reduced faulty-tolerance of the device 3.2 Safety instructions I The following safety instructions are also provided in the manual "Safety Notes and Regulations". This device meets the relevant safety regulations for IT equipment. If you have any questions about whether you can install the server in the intended environment, please contact your sales outlet or our customer service team. V CAUTION! The actions described in this manual shall be performed by technical specialists. A technical specialist is a person who is trained to install the server including hardware and software. Repairs to the device that do not relate to CSS failures shall be performed by service personnel. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Any failure to observe the guidelines in this manual, and any improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment. CX122 S1 Operating Manual 17

18 Safety instructions Keep this operating manual and the other documentation (such as the technical manual, CD) close to the device. All documentation must be included if the equipment is passed on to a third party. Before starting up V CAUTION! When installing the appliance and before placing it in service, please take note of the information on the required ambient conditions and the required technical infrastructure. The information you require here is contained in section "Technical data" on page 11. V CAUTION! When relocating the appliance: If the device is brought in from a cold environment, condensation may form both inside and on the outside of the device. Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. Installation, mounting and removal activities involving the CX1000 system unit may only be performed by technicians, service personnel or technical specialists. Ignoring the instructions in this manual can result in personal injury or damage to equipment (risk of tipping over, etc.). When the unit is transported, it is only allowed to have a lean angle of max. 15. Make sure that the floor at the final place of installation has sufficient load-bearing capacity. Route the cables in such a way that they do not form a potential hazard (make sure no one can trip over them) and that they cannot be damaged. For safety reasons, no more than one unit may be withdrawn from the rack at any one time during installation and maintenance work. Please keep in mind, that PRIMERGY CX122 S1 server nodes will tip over or fall out of the rack if slid out too far! The rack must be connected to the power supply by an authorized specialist (electrician). 18 Operating Manual CX122 S1

19 Safety instructions If necessary, have other people help you mount the individual components in the rack because of the weight involved. Install only system expansions that satisfy the requirements and rules governing safety. If you install other expansions, you may damage the system or violate these safety regulations. Information can be obtained from customer service or your local sales office. The AC main power connection for the PRIMERGY CX1000 system unit must be installed by an authorized electrician approved by the local utility company. Installation and operation V CAUTION! General Make sure that no objects (e.g. jewelry, paperclips etc.) or liquids can get inside the server (risk of electric shock, short circuit). Data cables must be adequately shielded. The EN and EN /2 standards apply for LAN cabling. The minimum requirement is the use of a category 5 screened LAN cable for 10/100 Mbit/s Ethernet, or a category 5e cable for Gigabit Ethernet. The requirements from the ISO/IEC specification must also be met. Route the cables in such a way that they do not create a potential hazard (make sure no-one can trip over them) and that they cannot be damaged. When connecting the server, refer to the relevant instructions in this manual. Never connect or disconnect data transmission lines during a storm (risk of lightning strike). In emergencies (e.g. damaged casing, controls or cables, penetration of liquids or foreign bodies), switch off the server immediately, remove all power plugs and contact your sales outlet or customer service team. CX122 S1 Operating Manual 19

20 Safety instructions PRIMERGY CX122 S1 The On/Off button does not isolate the device from the mains power supply. To disconnect it completely from the CX1000 power distribution unit, loosen the two knurled screws on the server front and slide the server out of the rack about 10 centimeters. Proper operation of the system (in accordance with IEC / EN ) is only ensured if the casing is completely assembled and the slot brackets of the installation slots have been fitted (electric shock, cooling, fire protection, interference suppression). When removing a PRIMERGY CX122 S1 server from the system unit, always install a dummy cover in the empty installation bay. Only install system expansions that satisfy the requirements and rules governing safety and electromagnetic compatibility and those relating to telecommunication terminals. If you install other expansions, they may damage the system or violate the safety regulations. Information on which system expansions are approved for installation can be obtained from our customer service center or your sales outlet. The components marked with a warning notice (e.g. lightning symbol) may only be opened, removed or exchanged by authorized, qualified personnel. A defective PRIMERGY CX122 S1 server node is maintained by Fujitsu service technicians. The warranty is void if the server is damaged during installation or replacement of system expansions. 20 Operating Manual CX122 S1

21 Safety instructions Modules with Electrostatic-Sensitive Devices Modules with electrostatic-sensitive devices are identified by the following sticker: Figure 1: ESD label When you handle components fitted with ESDs, you must always observe the following points: Switch off the system and remove the power plugs from the power outlets before installing or removing components with ESDs. You must always discharge static build-up (e.g. by touching a grounded object) before working with such components. Any devices or tools that are used must be free of electrostatic charge. Wear a suitable grounding cable that connects you to the external chassis of the system unit. Always hold components with ESDs at the edges or at the points marked green (touch points). Do not touch any connectors or conduction paths on an ESD. Place all the components on a pad which is free of electrostatic charge. I For a detailed description of how to handle ESD components, see the relevant European or international standards (EN , ANSI/ESD S20.20). CX122 S1 Operating Manual 21

22 CE conformity 3.3 CE conformity The system complies with the requirements of the EC directives 2004/108/EC regarding "Electromagnetic Compatibility" and 2006/95/EC "Low Voltage Directive". This is indicated by the CE marking (CE = Communauté Européenne). 3.4 FCC Class A Compliance Statement If there is an FCC statement on the device, then: The following statement applies to the products covered in this manual, unless otherwise specified herein. The statement for other products will appear in the accompanying documentation. I This equipment has been tested and found to comply with the limits for a "Class A" digital device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in strict accordance with the instructions, may cause harmful interference to radio communications. However, there is no warranty that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Fujitsu Technology Solutions is not responsible for any radio or television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other 22 Operating Manual CX122 S1

23 Environmental protection than those specified by Fujitsu Technology Solutions. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may violate FCC and ICES rules. V CAUTION: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 3.5 Environmental protection Environmentally-friendly product design and development This product has been designed in accordance with the Fujitsu Technology Solutions standard for "environmentally friendly product design and development". This means that key factors such as durability, selection and labeling of materials, emissions, packaging, ease of dismantling and recycling have been taken into account. This saves resources and thus reduces the harm done to the environment. Energy-saving information Devices that do not need to be constantly switched on should be switched off until they are needed as well as during long breaks and after completion of work. Packaging information Do not throw away the packaging. You may need it later for transporting the system. If possible, the equipment should only be transported in its original packaging. Information on handling consumables Please dispose of printer consumables and batteries in accordance with the applicable national regulations. CX122 S1 Operating Manual 23

24 Environmental protection In accordance with EU directives, batteries must not be disposed of with unsorted domestic waste. They can be returned free of charge to the manufacturer, dealer or an authorized agent for recycling or disposal. All batteries containing pollutants are marked with a symbol (a crossed-out garbage can). They are also marked with the chemical symbol for the heavy metal that causes them to be categorized as containing pollutants: Cd Cadmium Hg Mercury Pb Lead Labels on plastic casing parts Please avoid sticking your own labels on plastic parts wherever possible, since this makes it difficult to recycle them. Returns, recycling and disposal The device must not be disposed of with domestic waste. This device is labeled in compliance with European directive 2002/96/EC on waste electrical and electronic equipment (WEEE). This directive sets the framework for returning and recycling used equipment and is valid across the EU. When returning your used device, please use the return and collection systems available to you. Further information can be found at Details regarding the return and recycling of devices and consumables within Europe can also be found in the "Returning used devices" manual, via your local Fujitsu Technology Solutions branch or from our recycling center in Paderborn: Fujitsu Technology Solutions Recycling Center D Paderborn Tel Fax Operating Manual CX122 S1

25 4 Hardware installation V CAUTION! Follow the safety instructions in the chapter "Important information" on page 17. Do not expose the server to extreme environmental conditions (see "Ambient conditions" on page 13). Protect the server from dust, humidity and heat. Make sure that the server is acclimatized for the time indicated in this table before putting it into operation. Temperature difference ( C) Minimum acclimatization time (hours) Table 1: Acclimatization time In the table "Acclimatization time", the temperature difference refers to the difference between the operating environment temperature and the temperature to which the server was exposed previously (outside, transport or storage temperature). CX122 S1 Operating Manual 25

26 Installation Procedure 4.1 Installation Procedure Work through the installation steps in the specified order. The individual steps are described in detail in the next chapters. V CAUTION! Observe the safety and installation notes in the chapter "Important information" on page 17. I Your PRIMERGY CX122 S1 server is being already assembled into the PRIMERGY CX1000 and ready to operate. Ê Ê Ê Ê Make sure that the accompanying documentation (see "Documentation overview" on page 8) is complete. Print out the required PDF files, if necessary. Unpack all individual parts. Keep the original packaging in case you want to transport the server again. Check whether all the necessary details have been entered on the first page of the guarantee booklet. Check whether the items delivered match the delivery note. Notify your supplier immediately should you discover that the items delivered do not correspond to the delivery note. 26 Operating Manual CX122 S1

27 Installing / replacing a PRIMERGY CX122 S1 server 4.2 Installing / replacing a PRIMERGY CX122 S1 server V CAUTION! Follow the safety instructions in the chapter "Important information" on page Removing a PRIMERGY CX122 S1 server I A defective PRIMERGY CX122 S1 server is maintained by Fujitsu service technicians. The warranty is void if the server is damaged during installation or replacement of system expansions. Ê Shut down the server. For information on controls and indicators, please refer to section "Front panel" on page 41. Figure 2: Removing all cables from the front side of the server Ê Disconnect all cables from the server. I Cable guides ensure that the network cables remain located at their designated height units when unplugged. CX122 S1 Operating Manual 27

28 Installing / replacing a PRIMERGY CX122 S1 server Figure 3: Removing a server from the system unit (B) Ê Loosen the two knurled screws on the front cover (1). Ê Carefully slide the server out of the rack (2). V CAUTION! Please keep in mind, that PRIMERGY CX122 S1 server nodes will tip over or fall out of the rack if slid out too far! Ê Remove the defective server. V CAUTION! When removing a PRIMERGY CX122 S1 server from the system unit that is not replaced immediately, always install a dummy cover in the empty installation bay. For further information please refer to the operating manual of PRIMERGY CX Operating Manual CX122 S1

29 Installing / replacing a PRIMERGY CX122 S1 server Installing a PRIMERGY CX122 S1 server No additional mechanical parts such as support brackets or screws are required for the installation of a PRIMERGY CX122 S1 server in the CX1000 system unit. Figure 4: Mounting a server in the rack (A) Ê If missing, fit two cage nuts in the corresponding notches on the left and right support uprights. CX122 S1 Operating Manual 29

30 Installing / replacing a PRIMERGY CX122 S1 server Figure 5: Mounting a server in the rack (B) Ê Insert the server into the rack at the desired installation position. Ê Slide the server in the direction of the arrow until it stops (1). I The PRIMERGY CX122 S1 power supply unit will automatically be connected with the power distribution unit in the CX1000 system unit. Ê Secure the server with two knurled screws (2). 30 Operating Manual CX122 S1

31 Installing / replacing a PRIMERGY CX122 S1 server Figure 6: Mounting a server in the rack (C) Ê Reconnect all cables. For further information network cabling, please refer to section "Network cabling" on page 34. CX122 S1 Operating Manual 31

32 Connecting devices and cables 4.3 Connecting devices and cables V CAUTION! You must use shielded cables for the LAN cabling. The connectors for external devices and network connections are on the front of the server. The standard connectors (figure 7) are marked with symbols, some are color-coded. Figure 7: Front connection panel 1 VGA connector 5 System LAN connector 2 2 Service LAN connector for irmc 6 System LAN connector 1 server management function 3 USB connector 7 7 optional LAN connector 4 USB connector 6 8 optional LAN connector 32 Operating Manual CX122 S1

33 Connecting devices and cables Connecting devices I Some of the devices connected require special software (e.g. drivers) (see documentation for the connected device). If components with large power requirements (e.g. external USB hard disk drives) are connected simultaneously, these USB ports may be switched off Connecting / disconnecting cables V CAUTION! Always read the documentation supplied with the device you wish to connect. Never connect, or disconnect cables during a thunderstorm. Never pull on a cable when disconnecting it. Always take hold of the cable by the plug. CX122 S1 Operating Manual 33

34 Connecting devices and cables Network cabling LAN cables are routed through cable guides on the right side of the rack and connected to vertically mounted network switches. The cable guides ensure that the network cables remain located at their designated height units, even if they are unplugged for the purpose of replacing a server node. Up to six color coded cable sets are employed on a system unit, each of them assigned to one of the up to six CX122 S1 LAN ports and one of up to six network switches. There are five different configurations of the PRIMERGY CX1000 S1 system unit: S F3608-E1 S F3608-E2 S F3608-E3 S F3608-E4 S F3608-E5 LAN switches 1 (onboard LAN 1) 2 (onboard LAN 2) 1 (onboard LAN 1) 2 (onboard LAN 2) 5 (Service LAN) 1 (onboard LAN 1) 2 (onboard LAN 2) 3 (LAN Card 1) 4 (LAN Card 2) 1 (onboard LAN 1) 2 (onboard LAN 2) 3 (LAN Card 1) 4 (LAN Card 2) 5 (Service LAN) 1 (onboard LAN 1) 2 (onboard LAN 2) 3 (LAN Card 1) 4 (LAN Card 2) 5 (LAN Card 3) 6 (LAN Card 4) Table 2: LAN cabling color coding (switches) Cable sets green blue green blue black green blue yellow grey green blue yellow grey black green blue yellow grey black red The color coded LAN cables are assigned to the PRIMERGY CX122 S1 network ports as follows: 34 Operating Manual CX122 S1

35 Connecting devices and cables Figure 8: LAN cabling color coding (servers) CX122 S1 Operating Manual 35

36 Connecting devices and cables Onboard server ports P1 and P2 to network switches 1 and 2 Connection Switch Server Port Label Port Label Switch 1 to Server 1 Port 5 SW1P5 Port 1 SV1P1 Switch 2 to Server 1 Port 5 SW2P5 Port 2 SV1P2 Switch 1 to Server 2 Port 6 SW1P6 Port 1 SV2P1 Switch 2 to Server 2 Port 6 SW2P6 Port 2 SV2P2 Switch 1 to Server 3 Port 7 SW1P7 Port 1 SV3P1 Switch 2 to Server 3 Port 7 SW2P7 Port 2 SV3P2 Switch 1 to Server 4 Port 8 SW1P8 Port 1 SV4P1 Switch 2 to Server 4 Port 8 SW2P8 Port 2 SV4P2 and so on... LAN card server ports P3 and P4 to network switches 3 and 4 Connection Switch Server Port Label Port Label Switch 3 to Server 1 Port 5 SW3P5 Port 3 SV1P3 Switch 4 to Server 1 Port 5 SW4P5 Port 4 SV1P4 Switch 3 to Server 2 Port 6 SW3P6 Port 3 SV2P3 Switch 4 to Server 2 Port 6 SW4P6 Port 4 SV2P4 Switch 3 to Server 3 Port 7 SW3P7 Port 3 SV3P3 Switch 4 to Server 3 Port 7 SW4P7 Port 4 SV3P4 Switch 3 to Server 4 Port 8 SW3P8 Port 3 SV4P3 Switch 4 to Server 4 Port 8 SW4P8 Port 4 SV4P4 and so on Operating Manual CX122 S1

37 Connecting devices and cables LAN card server ports P5 and P6 to network switches 5 and 6 Connection Switch Server Port Label Port Label Switch 5 to Server 1 Port 5 SW5P5 Port 5 SV1P5 Switch 6 to Server 1 Port 5 SW6P5 Port 6 SV1P6 Switch 5 to Server 2 Port 6 SW5P6 Port 5 SV2P5 Switch 6 to Server 2 Port 6 SW6P6 Port 6 SV2P6 Switch 5 to Server 3 Port 7 SW5P7 Port 5 SV3P5 Switch 6 to Server 3 Port 7 SW6P7 Port 6 SV3P6 Switch 5 to Server 4 Port 8 SW5P8 Port 5 SV4P5 Switch 6 to Server 4 Port 8 SW6P8 Port 6 SV4P6 and so on... Server port SL (Service LAN) to network switch 5 I Service LAN port is not available in combination with Quad-Port LAN card configurations. Connection Switch Server Port Label Port Label Switch 5 to Server 1 Port 5 SW5P5 Port SL SV1SL Switch 5 to Server 2 Port 6 SW5P6 Port SL SV2SL Switch 5 to Server 3 Port 7 SW5P7 Port SL SV3SL Switch 5 to Server 4 Port 8 SW5P8 Port SL SV4SL Switch 5 to Server 5 Port 9 SW5P9 Port SL SV5SL and so on... CX122 S1 Operating Manual 37

38 Connecting devices and cables 38 Operating Manual CX122 S1

39 5 Starting up and operation V CAUTION! Follow the safety instructions in chapter "Important information" on page LAN indicators Figure 9: LAN indicators on the front connection panel CX122 S1 Operating Manual 39

40 LAN indicators 1/2 Service LAN (onboard) 1 LAN activity indicator 2 LAN transfer rate indicator green ON: Active connection green FLASHING: Transmit / Receive activity OFF: 10 Mbit/s green ON: 100 Mbit/s 3/4 Gigabit LAN (onboard) 3 LAN activity indicator 4 LAN transfer rate indicator green ON: Active connection green FLASHING: Transmit / Receive activity OFF: 10 Mbit/s green ON: 100 Mbit/s orange ON: 1000 Mbit/s 5/6 7/8 Gigabit LAN (optional expansion card) 5/6 LAN activity indicator 7/8 LAN transfer rate indicator green ON: Active connection green FLASHING: Transmit / Receive activity OFF: 10 Mbit/s green ON: 100 Mbit/s orange ON: 1000 Mbit/s 40 Operating Manual CX122 S1

41 Front panel 5.2 Front panel Figure 10: PRIMERGY CX122 S1 front panel 1 ID indicator / ID button 4 Hard disk drive activity indicator 2 CSS indicator 5 Power-on indicator / On/Off button (not supported by PRIMERGY CX122 S1) 6 Reset button 3 Global Error indicator 7 NMI button CX122 S1 Operating Manual 41

42 Front panel Controls On/Off button When the system is switched off, it can be switched on again by pressing the On/Off button. When the system is operating, pressing the On/Off button will switch off the system. I The On/Off button does not isolate the device from the mains voltage. To disconnect it completely from the PRIMERGY CX1000 power distribution unit, loosen the two knurled screws on the server front and slide the server out of the rack about 10 centimeters. NMI RST ID NMI button V CAUTION! Do not press! Risk of loss of data! The NMI button may only be used by service. Reset button Pressing the reset button reboots the system. V CAUTION! Risk of loss of data! ID button Pressing the ID button toggles the ID indicator on the PRIMERGY CX122 S1 operating panel. 42 Operating Manual CX122 S1

43 Front panel Indicators Power-on indicator Lights up green when the server is switched ON. Hard disk activity indicator (green) Lights up green when an internal hard disk drive is being accessed.! CSS ID Global Error indicator (orange) Lights up orange if a prefailure event has been detected that requires (precautionary) service intervention. Flashes orange if an error was detected that requires service intervention. Does not light up if there is no critical event. If the event is still acute after a power failure, the indicator is activated after the restart. The indicator also lights up in standby mode. You can find more details on the indicated errors in the System Event Log. CSS indicator (yellow) Not used. At present, the PRIMERGY CX122 S1 server does not comprise any CSS components. ID indicator (blue) The system has been selected by pressing the ID button. To deactivate, press the button again. CX122 S1 Operating Manual 43

44 Switching the server on and off 5.3 Switching the server on and off V CAUTION! The On/Off button does not isolate the device from the mains voltage. To disconnect it completely from the PRIMERGY CX1000 power distribution unit, loosen the two knurled screws on the server front and slide the server out of the rack about 10 centimeters Switching the server on The Power-on indicator (item 5 in figure 10 on page 41) lights up green. Starting up the server for the first time When starting up a PRIMERGY CX122 S1 server node for the first time, there are several installation options, depending on the system configuration. For further information, please refer to section "Configuring the server" on page 45. System already installed Hard disk drives installed - Local boot Ê Press the On/Off button (item 5 in figure 10 on page 41). The server is switched on, performs a system test and boots the operating system. No hard disk drives installed - iscsi boot iscsi (Internet SCSI) is a protocol for linking servers and data storage facilities, similar to the Fibre Channel Protocol (FCP). iscsi means SCSI over Internet Protocol. iscsi boot allows a server to be booted remotely from a drive in an iscsi-based Storage Area Network (SAN). For further instructions, please refer to the iscsi Boot for PRIMERGY Servers with Intel Network Controllers installation and configuration guide, available from the ServerView Suite DVD 2 or at 44 Operating Manual CX122 S1

45 Configuring the server Switching the server off Ê Shut down the server properly. The power-on indicator turns off (see item 5 in figure 10 on page 41). I If the server does not shut down completely, press the On/Off button for at least four seconds and/or send a corresponding control signal for power button override. 5.4 Configuring the server Operating system installation Configuring the onboard SATA controller I If RAID mode is enabled (default setting) you can configure the onboard SATA controller during boot-up. The default setting is RAID mode. Compatible and native mode are also released. For further information refer to "D2899 BIOS Setup Utility for PRIMERGY CX122 Reference Manual". If RAID mode is enabled, the RAID must be configured during bootup to use hard disk drives. For further information, refer to the "Embedded MegaRAID Software User s Guide" (on the ServerView Suite DVD 2 under Industry Standard Servers - Expansion Cards - Storage Adapters - LSI RAID / SCSI Controllers). The PDF files of the manuals can also be downloaded free of charge from the Internet. The overview page showing the online documentation available on the Internet can be found using the URL (for EMEA market): The PRIMERGY server documentation can be accessed using the Industry standard servers navigation option. For the Japanese market please use the URL: I For RAID management use the tool MegaCLI (available via download). CX122 S1 Operating Manual 45

46 Configuring the server When starting up a PRIMERGY CX122 S1 server node for the first time, there are several installation options, depending on the system configuration: Hard disk drives installed - Preboot Execution Environment (PXE) boot (recommended) PXE boot requires your machine's BIOS to make a request of a TFTP server for a bootable image (the equivalent of inserting a CD and booting). It is the environment that allows devices to boot up via their network interface. When shipping, the boot sequence of each PRIMERGY CX122 S1 server has been configured to network booting. Right after the power on self test process (POST), the system will execute the PXE bootstrap session, looking for DHCP servers from the network. After selecting the required PXE boot server, the bootstrapping process begins and the PXE firmware asks for the exact path of the NBP (Network Bootstrap Program). After receiving this path, the download process begins. This is done via the Trivial File Transfer Protocol (TFTP, UDP, port 69). Ê Dedicate one server from your network to be a PXE server with the DHCP and TFTP services configured and running. Ê Press the On/Off button (item 5 in figure 10 on page 41). Ê The PXE server will reply to your server s PXE boot request and aid the client system during its bootstrap session. Follow the on-screen instructions. 46 Operating Manual CX122 S1

47 Configuring the server Hard disk drives installed - Local USB installation Instead of network booting, you can also boot and install your PRIMERGY CX122 S1 server node from local USB media. Ê Ê Ê Ê Connect a USB storage medium (hard disk drive, optical drive or flash media) containing a bootable image to your server. Connect a USB mouse / keyboard and VGA display to your server. Switch on the display. Make sure that none of the servers from your network has been dedicated to be a PXE server. Ê Press the On/Off button (item 5 in figure 10 on page 41). Ê Your PRIMERGY CX122 S1 server node will boot from the local disk image. Follow the on-screen instructions. No hard disk drives installed - iscsi boot iscsi (Internet SCSI) is a protocol for linking servers and data storage facilities, similar to the Fibre Channel Protocol (FCP). iscsi means SCSI over Internet Protocol. iscsi boot allows a server to be booted remotely from a drive in an iscsi-based Storage Area Network (SAN). For further instructions, please refer to the iscsi Boot for PRIMERGY Servers with Intel Network Controllers installation and configuration guide, available from the ServerView Suite DVD 2 or at CX122 S1 Operating Manual 47

48 Configuring the server 48 Operating Manual CX122 S1

49 Index A acclimatization time 25 ambient conditions CX122 S1 13 C CE marking 12, 22 Class A Compliance Statement 22 configuration CX122 S1 45 connectors CX122 S1 32 consumables 23 CSS indicator 43 CX122 S1 41 CX122 S1 configuration 45 connecting cables 32 connecting devices 32 installation 29 ports 32 removal 27 replacement 27 startup 44 switching off 44 switching on 44 D disposal, devices 24 documentation overview 8 E electrical data CX122 S1 11 electromagnetic compatibility 22 EMC directive 12 environmental protection 23 ESD (electrostatic-sensitive devices) 21 expansion cards 9 F FCC statement 22 features 9 expansion cards 9 hard disk drives 9 high capacity 9 power supply 9 system board 9 ventilation 9 G Global Error indicator 43 CX122 S1 41 H hard disk activity indicator 43 hard disk drives 9 HDD indicator 41 I ID button 42 CX122 S1 41 ID indicator 43 CX122 S1 41 indicators CSS 41, 43 Global Error 41, 43 hard disk activity 43 HDD activity 41 ID 41, 43 Power-on 41 system error 43 information, additional 9 installation CX122 S1 27 L labels 24 LAN 39 cabling 34 indicators 39 CX122 S1 Operating Manual 49

50 Low Voltage Directive 12, 22 M meaning of the symbols 10 mechanical values CX122 S1 12 N network 39 cabling 34 network indicators CX122 S1 39 Network switches 34 NMI button 42 CX122 S1 41 noise level CX122 S1 13 notational conventions 10 power-on indicator 43 Service LAN onboard 40 startup 39 switching on/off CX122 S1 44 system board 9 T target group 7 technical data 11 V ventilation clearances CX122 S1 13 O On/Off button 42 CX122 S1 41 operation 39 P packaging 23 ports 32 Power-on indicator CX122 S1 41 power-on indicator 43 R recycling devices 24 regulations and standards CX122 S1 12 reset button 42 CX122 S1 41 returning devices 24 S safety instructions 17 safety standards CX122 S1 12 saving energy 23 server 50 Operating Manual CX122 S1