PRIMERGY BX400 S1 System Unit

Transcription

1 Options Guide - English PRIMERGY BX400 S1 System Unit Options Guide December 2010

2 Comments Suggestions Corrections The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs. Feel free to send us your comments by to Certified documentation according to DIN EN ISO 9001:2008 To ensure a consistently high quality standard and user-friendliness, this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001:2008. cognitas. Gesellschaft für Technik-Dokumentation mbh Copyright and Trademarks Copyright 2010 FUJITSU LIMITED All rights reserved. Delivery subject to availability; right of technical modifications reserved. All hardware and software names used are trademarks of their respective manufacturers. The contents of this manual may be revised without prior notice. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. No part of this manual may be reproduced in any form without the prior written permission of Fujitsu. Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of Microsoft Corporation in the USA and other countries. Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the USA and other countries.

3 Before reading this manual For your safety This manual contains important information for safely and correctly using this product. Carefully read the manual before using this product. Pay particular attention to the accompanying manual "Safety Notes and Regulations" and ensure these safety notes are understood before using the product. Keep this manual and the manual "Safety Notes and Regulations" in a safe place for easy reference while using this product. Radio interference This product is a "Class A" ITE (Information Technology Equipment). In a domestic environment this product may cause radio interference, in which case the user may be required to take appropriate measures. VCCI-A Aluminum electrolytic capacitors The aluminum electrolytic capacitors used in the product's printed circuit board assemblies and in the mouse and keyboard are limited-life components. Use of these components beyond their operating life may result in electrolyte leakage or depletion, potentially causing emission of foul odor or smoke. As a guideline, in a normal office environment (25 C) operating life is not expected to be reached within the maintenance support period (5 years). However, operating life may be reached more quickly if, for example, the product is used in a hot environment. The customer shall bear the cost of replacing replaceable components which have exceeded their operating life. Note that these are only guidelines, and do not constitute a guarantee of trouble-free operation during the maintenance support period. High safety use This product has been designed and manufactured to be used in commercial and/or industrial areas as a server. When used as visual display workplace, it must not be placed in the direct field of view to avoid incommoding reflections (applies only to TX server systems). The device has not been designed or manufactured for uses which demand an extremely high level of safety and carry a direct and serious risk of life or body if such safety cannot be assured. BX400 S1 Options Guide

4 These uses include control of nuclear reactions in nuclear power plants, automatic airplane flight control, air traffic control, traffic control in mass transport systems, medical devices for life support, and missile guidance control in weapons systems (hereafter, "high safety use"). Customers should not use this product for high safety use unless measures are in place for ensuring the level of safety demanded of such use. Please consult the sales staff of Fujitsu if intending to use this product for high safety use. Measures against momentary voltage drop This product may be affected by a momentary voltage drop in the power supply caused by lightning. To prevent a momentary voltage drop, use of an AC uninterruptible power supply is recommended. (This notice follows the guidelines of Voltage Dip Immunity of Personal Computer issued by JEITA, the Japan Electronics and Information Technology Industries Association.) Technology controlled by the Foreign Exchange and Foreign Trade Control Law of Japan Documents produced by Fujitsu may contain technology controlled by the Foreign Exchange and Foreign Trade Control Law of Japan. Documents which contain such technology should not be exported from Japan or transferred to non-residents of Japan without first obtaining authorization in accordance with the above law. Harmonic Current Standards This product conforms to harmonic current standard JIS C Only for the Japanese market: About SATA hard disk drives The SATA version of this server supports hard disk drives with SATA / BC-SATA storage interfaces. Please note that the usage and operation conditions differ depending on the type of hard disk drive used. Please refer to the following internet address for further information on the usage and operation conditions of each available type of hard disk drive: Options Guide BX400 S1

5 Contents 1 Introduction Concept and target groups Documentation overview Expansions and upgrades Notational conventions Procedure Safety instructions Preparation Floorstand model Opening the system unit Rack model Optical Disk Drive (ODD) Rack model Floorstand model ServerView Local Service Display for Blade Conversion from a rack model to a floorstand model Completion Floorstand model BX400 S1 Options Guide

6 Contents 8.2 Rack model Index Options Guide BX400 S1

7 1 Introduction The PRIMERGY BX400 S1 blade server is a highly compact, energy-saving and scalable server system. With its advanced infrastructure modules, the BX400 S1 system unit offers the server blades a high level of connectivity and availability. It is available as a rack or floorstand model. The rack model can be converted to a floorstand model using an optional conversion kit. 1.1 Concept and target groups This Options Guide shows you how to extend and upgrade your system unit. V CAUTION! The activities described in this manual may only be performed by technical specialists. I The installation and removal of the hot-plug components is described in the Operating Manual supplied with the system unit. 1.2 Documentation overview More information on your PRIMERGY BX400 S1 system unit can be found in the following documents: "Quick Start Hardware - PRIMERGY BX400 S1" leaflet " はじめにお読みください -PRIMERGY BX400 S1" for the Japanese market (only included as a printed copy) "Safety Notes and Regulations" manual " 安全上のご注意 " for the Japanese market "Warranty" manual " 保証書 " for the Japanese market "ServerView Suite Local Service Concept - LSC" manual "Returning used devices" manual and "Service Desk" leaflet " サポート & サービス " for the Japanese market "PRIMERGY BX400 S1 Blade Server System Unit Operating Manual" "PRIMERGY BX400 S1 System Unit Options Guide" BX400 S1 Options Guide 7

8 Introduction I PRIMERGY manuals are available in PDF format on the ServerView Suite DVD 2. The ServerView Suite DVD 2 is part of the ServerView Suite supplied with every server. If you no longer have the ServerView Suite DVDs, you can obtain the relevant current versions using the order number U15000-C289 (the order number for the Japanese market: please refer to the configurator of the server The PDF files of the manuals can also be downloaded free of charge from the Internet. The overview page showing the online documentation available on the Internet can be found using the URL (for EMEA market): The PRIMERGY server documentation can be accessed using the Industry standard servers navigation option. For the Japanese market please use the URL: Further sources of information: PRIMERGY Abbreviations and Glossary on the ServerView Suite DVD 2 Manual for the monitor Documentation for the boards and drives Operating system documentation Information files in your operating system 8 Options Guide BX400 S1

9 Introduction 1.3 Expansions and upgrades Accessible drive One bay is available for an optical disk drive (ODD) (DVD or Blue-ray). It is located on the upper front bezel (rack model) or on the Front-Side I/O Module (FSIOM) (floorstand model). ServerView Local Service Display for Blade You can install a ServerView Local Service Display for Blade instead of a front control panel for local administration and easier identification of defective components (rack model). The floorstand model is factory equipped with the ServerView Local Service Display for Blade. Conversion from a rack model to a floorstand model The rack model can be optionally converted to floorstand model using a conversion kit. 1.4 Notational conventions The following notational conventions are used in this manual: Text in italics "Quotation marks" V CAUTION! I indicates commands or menu items. indicate names of chapters and terms that are being emphasized. describes activities that must be performed in the order shown. pay particular attention to texts marked with this symbol. Failure to observe this warning may endanger your life, destroy the system or lead to the loss of data. indicates additional information, notes and tips. BX400 S1 Options Guide 9

10 Introduction 10 Options Guide BX400 S1

11 2 Procedure V CAUTION! The actions described in this manual shall be performed by technical specialists. A technical specialist is a person who is trained to install the server including hardware and software. Repairs to the device that do not relate to CSS failures shall be performed by service personnel. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Any failure to observe the guidelines in this manual, and any improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment. First of all, carefully read the safety instructions in the chapter "Safety instructions" on page 13. Make sure that all necessary manuals (see the section "Documentation overview" on page 7) are available; print the PDF files if required. Most importantly, you will need the Operating Manual for the system unit. Shut the system unit down correctly and disconnect the power cords and open the system unit as described in the chapter "Preparation" on page 21. Carry out the expansion or upgrade of your system unit as described in the pertinent chapter. I Installation and removal of the hot-plug components are described in the Operating Manual. Close the system unit, connect it to the power outlet, and switch it on as described in the chapter "Completion" on page 57. Start the operating system and make the appropriate configuration if necessary (see the Operating Manual of the server blade). I For the latest information on optional products provided for the BX400 S1 system unit see the configurator of the system unit: (for the EMEA market) (for the Japanese market) BX400 S1 Options Guide 11

12 Procedure 12 Options Guide BX400 S1

13 3 Safety instructions I The following safety instructions are also provided in the manual "Safety Notes and Regulations" or " 安全上のご注意 ". This device meets the relevant safety regulations for IT equipment. If you have any questions about whether you can install the server in the intended environment, please contact your sales outlet or our customer service team. V CAUTION! The actions described in this manual shall be performed by technical specialists. A technical specialist is a person who is trained to install the server including hardware and software. Repairs to the device that do not relate to CSS failures shall be performed by service personnel. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. Any failure to observe the guidelines in this manual, and any improper repairs could expose the user to risks (electric shock, energy hazards, fire hazards) or damage the equipment. Before installing/removing internal options to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the power outlet. Failure to do so can cause electric shock. BX400 S1 Options Guide 13

14 Safety instructions Before starting up V CAUTION! During installation and before operating the device, observe the instructions on environmental conditions for your device. If the device is brought in from a cold environment, condensation may form both inside and on the outside of the device. Wait until the device has acclimatized to room temperature and is absolutely dry before starting it up. Material damage may be caused to the device if this requirement is not observed. Transport the device only in the original packaging or in packaging that protects it from knocks and jolts. Installation and operation V CAUTION! This unit should not be operated in ambient temperatures above 35 C. If the unit is integrated into an installation that draws power from an industrial power supply network with an IEC309 connector, the power supply's fuse protection must comply with the requirements for nonindustrial power supply networks for type A connectors. The unit automatically adjusts itself to a mains voltage in a range of 100 V V. Ensure that the local mains voltage lies within these limits. This device must only be connected to properly grounded power outlets or insulated sockets of the rack's internal power supply with tested and approved power cords. Ensure that the device is connected to a properly grounded power outlet close to the device. 14 Options Guide BX400 S1

15 Safety instructions V CAUTION! Ensure that the power sockets on the device and the properly grounded power outlets are freely accessible. The On/Off button or the main power switch (if present) does not isolate the device from the mains power supply. To disconnect it completely from the mains power supply, unplug all network power plugs from the properly grounded power outlets. Always connect the server and the attached peripherals to the same power circuit. Otherwise you run the risk of losing data if, for example, the server is still running but a peripheral device (e.g. memory subsystem) fails during a power outage. Data cables must be adequately shielded. Ethernet cabling has to comply with EN and EN /2 standards or ISO/IEC standard respectively. The minimum requirement is a Category 5 shielded cable for 10/100 Ethernet, or a Category 5e cable for Gigabit Ethernet. Route the cables in such a way that they do not create a potential hazard (make sure no-one can trip over them) and that they cannot be damaged. When connecting the server, refer to the relevant instructions in this manual. Never connect or disconnect data transmission lines during a storm (risk of lightning hazard). Make sure that no objects (e.g. jewelry, paperclips etc.) or liquids can get inside the server (risk of electric shock, short circuit). In emergencies (e.g. damaged casing, controls or cables, penetration of liquids or foreign bodies), switch off the server immediately, remove all power plugs and contact your sales outlet or customer service team. BX400 S1 Options Guide 15

16 Safety instructions V CAUTION! Proper operation of the system (in accordance with IEC /2 resp. EN /2) is only ensured if the casing is completely assembled and the rear covers for the installation slots have been fitted (electric shock, cooling, fire protection, interference suppression). Only install system expansions that satisfy the requirements and rules governing safety and electromagnetic compatibility and those relating to telecommunication terminals. If you install other expansions, they may damage the system or violate the safety regulations. Information on which system expansions are approved for installation can be obtained from our customer service center or your sales outlet. The components marked with a warning notice (e.g. lightning symbol) may only be opened, removed or exchanged by authorized, qualified personnel. Exception: CSS components can be replaced. The warranty is void if the server is damaged during installation or replacement of system expansions. Only set screen resolutions and refresh rates that are specified in the operating manual for the monitor. Otherwise, you may damage your monitor. If you are in any doubt, contact your sales outlet or customer service center. Before installing/removing internal options to/from the server, turn off the server, all peripheral devices, and any other connected devices. Also unplug all power cords from the outlet. Failure to do so can cause electric shock. Do not damage or modify internal cables or devices. Doing so may cause a device failure, fire, or electric shock. Devices inside the server remain hot after shutdown. Wait for a while after shutdown before installing or removing internal options. The circuit boards and soldered parts of internal options are exposed and can be damaged by static electricity. Before handling them, first touch a metal part of the server to discharge static electricity from your body. Do not touch the circuitry on boards or soldered parts. Hold the metallic areas or the edges of the circuit boards. 16 Options Guide BX400 S1

17 Safety instructions V CAUTION! Install the screw removed during installation/detaching Internal Options in former device/position. To use a screw of the different kind causes a breakdown of equipment. The installation indicated on this note is sometimes changed to the kind of possible options without notice. BX400 S1 Options Guide 17

18 Safety instructions Working with CDs/DVDs/BDs and optical drives When working with devices with optical drives, these instructions must be followed. V CAUTION! Only use CDs/DVDs/BDs that are in perfect condition, in order to prevent data loss, equipment damage and injury. Check each CD/DVD/BD for damage, cracks, breakages etc. before inserting it in the drive. Note that any additional labels applied may change the mechanical properties of a CD/DVD/BD and cause imbalance. Damaged and imbalanced CDs/DVDs/BDs can break at high drive speeds (data loss). Under certain circumstances, sharp CD/DVD/BD fragments can pierce the cover of the optical drive (equipment damage) and can fly out of the device (danger of injury, particularly to uncovered body parts such as the face or neck). High humidity and airborne dust levels are to be avoided. Electric shocks and/or server failures may be caused by liquids such as water, or metallic items, such as paper clips, entering a drive. Shocks and vibrations are also to be avoided. Do not insert any objects other than the specified CDs/DVDs/BDs. Do not pull on, press hard, or otherwise handle the CD/DVD/BD tray roughly. Do not disassemble the optical drive. Before use, clean the optical disk tray using a soft, dry cloth. As a precaution, remove disks from the optical drive when the drive is not to be used for a long time. Keep the optical disk tray closed to prevent foreign matter, such as dust, from entering the optical drive. Hold CDs/DVDs/BDs by their edges to avoid contact with the disk surface. 18 Options Guide BX400 S1

19 Safety instructions Do not contaminate the CD/DVD/BD surface with fingerprints, oil, dust, etc. If dirty, clean with a soft, dry cloth, wiping from the center to the edge. Do not use benzene, thinners, water, record sprays, antistatic agents, or silicone-impregnated cloth. Be careful not to damage the CD/DVD/BD surface. Keep the CDs/DVDs/BDs away from heat sources. Do not bend or place heavy objects on CDs/DVDs/BDs. Do not write with ballpoint pen or pencil on the label (printed) side. Do not attach stickers or similar to the label side. Doing so may cause rotational eccentricity and abnormal vibrations. When a CD/DVD/BD is moved from a cold place to a warm place, moisture condensation on the CD/DVD/BD surface can cause data read errors. In this case, wipe the CD/DVD/BD with a soft, dry cloth then let it air dry. Do not dry the CD/DVD/BD using devices such as a hair dryer. To avoid dust, damage, and deformation, keep the CD/DVD/BD in its case whenever it is not in use. Do not store CDs/DVDs/BDs at high temperatures. Areas exposed to prolonged direct sunlight or near heating appliances are to be avoided. I You can prevent damage from the optical drive and the CDs/DVDs/BDs, as well as premature wear of the disks, by observing the following suggestions: Only insert disks in the drive when needed and remove them after use. Store the disks in suitable sleeves. Protect the disks from exposure to heat and direct sunlight. Laser information The optical drive complies with IEC laser class 1. V CAUTION! The optical drive contains a light-emitting diode (LED), which under certain circumstances produces a laser beam stronger than laser class 1. Looking directly at this beam is dangerous. Never remove parts of the optical drive casing! BX400 S1 Options Guide 19

20 Safety instructions Modules with Electrostatic-Sensitive Devices Modules with electrostatic-sensitive devices are identified by the following sticker: Figure 1: ESD label When you handle components fitted with ESDs, you must always observe the following points: Switch off the system and remove the power plugs from the power outlets before installing or removing components with ESDs. You must always discharge static build-up (e.g. by touching a grounded object) before working with such components. Any devices or tools that are used must be free of electrostatic charge. Wear a suitable grounding cable that connects you to the external chassis of the system unit. Always hold components with ESDs at the edges or at the points marked green (touch points). Do not touch any connectors or conduction paths on an ESD. Place all the components on a pad which is free of electrostatic charge. I For a detailed description of how to handle ESD components, see the relevant European or international standards (EN , ANSI/ESD S20.20). 20 Options Guide BX400 S1

21 4 Preparation V CAUTION! Follow the safety instructions in the chapter "Safety instructions" on page Floorstand model Opening the system unit Terminate all applications and shut down the system unit correctly. If your operating system has not switched off the server, press the On/Off button. Pull all power cables out of the power outlet. Unlock the door and remove the key. Figure 2: Removing the door Pull the hinge pin (see circle) downward and remove the door. BX400 S1 Options Guide 21

22 Preparation 4.2 Rack model Terminate all applications and shut down the system unit correctly. If your operating system has not switched off the server, press the On/Off button. Pull all power cables out of the power outlet. 22 Options Guide BX400 S1

23 5 Optical Disk Drive (ODD) V CAUTION! When installing the ODD, hold it by the side. Applying force to the top may cause failures. Follow the safety instructions in the chapter "Safety instructions" on page 13. Figure 3: Preparing the ODD Fasten the engaging hook on the ODD. BX400 S1 Options Guide 23

24 Optical Disk Drive (ODD) 5.1 Rack model The ODD mounting bay is located on the upper front bezel of the system unit. Empty the sever blade slots 7 and 8. See the Operating Manual for how to remove server blades, storage blades and server blade dummy modules. Figure 4: Removing the ODD dummy module Press the green engaging hook up (1) and to the front side of the system unit (2) to remove the ODD dummy module. 24 Options Guide BX400 S1

25 Optical Disk Drive (ODD) Figure 5: Inserting the ODD Push the ODD in the bay of the system unit until it engages. Reinstall server blades, storage blades or server blade dummy modules in slots 7 and 8, see the Operating Manual. Connect the system unit to the power outlet, and switch it on as described in the chapter "Completion" on page 57. BX400 S1 Options Guide 25

26 Optical Disk Drive (ODD) 5.2 Floorstand model The ODD mounting bay is located on the FSIOM. Empty the sever blade slots 7 and 8. See the Operating Manual for how to remove server blades, storage blades and server blade dummy modules. Figure 6: Disengaging the FSIOM Disengage the lock of the FSIOM (1) and pull it out of the system unit up to the stop (2) I If the FSIOM is hard to unlock, press it at the left front (vicinity of server blade slots 7 and 8) as you release it. 26 Options Guide BX400 S1

27 Optical Disk Drive (ODD) Figure 7: Removing the FSIOM Disconnect the door sensor cable (small circle) and the LCD cable (large circle) from the FSIOM. Unlock the FSIOM (1) and pull it out of the system unit completely (2). Figure 8: Removing the ODD dummy module from the FSIOM Unlock the ODD dummy module (1) and remove it from the FSIOM (2). BX400 S1 Options Guide 27

28 Optical Disk Drive (ODD) Figure 9: Inserting the ODD in the FSIOM Push the ODD into the bay of the FSIOM until the engaging hook (1) under the metal holder (2) locks in place. Figure 10: Connecting the SATA cable to the ODD Connect the other plug of the SATA cable to the port on the ODD (see circle) and put the cable in the cable clamp (1). 28 Options Guide BX400 S1

29 Optical Disk Drive (ODD) Figure 11: Connecting the door sensor cable and the LCD cable to the FSIOM Push the FSIOM into the system unit until the security lock engages. Connect the door sensor cable (small circle) and the LCD cable (large circle) to the FSIOM. Disengage the security lock of the FSIOM (1) and push it completely into the system unit (2). The FSIOM clicks into place in its final position. Reinstall server blades, storage blades or server blade dummy modules in slots 7 and 8, see the Operating Manual. Connect the system unit to the power outlet, and switch it on as described in the chapter "Completion" on page 57. BX400 S1 Options Guide 29

30 Optical Disk Drive (ODD) 30 Options Guide BX400 S1

31 6 ServerView Local Service Display for Blade V CAUTION! Follow the safety instructions in the chapter "Safety instructions" on page 13. Figure 12: Front control panel The ServerView Local Service Display for Blade is an option in the rack model of the BX400 S1 system unit. The ServerView Local Service Display for Blade is placed in the FSIOM instead of the front control panel. I The floorstand model is factory equipped with the ServerView Local Service Display for Blade. Empty the sever blade slots 7 and 8. See the Operating Manual for how to remove server blades, storage blades and server blade dummy modules. BX400 S1 Options Guide 31

32 ServerView Local Service Display for Blade Figure 13: Disengaging the FSIOM Disengage the lock of the FSIOM (1) and pull it out of the system unit up to the stop (2). I If the FSIOM is hard to unlock, press it at the top front as you release it. 32 Options Guide BX400 S1

33 ServerView Local Service Display for Blade Figure 14: Removing the FSIOM Unplug the SATA cable (1). Unlock the FSIOM (2) and pull it out of the system unit completely. Figure 15: Removing the front control panel carrier from the FSIOM Unplug the LCD cable from the front control panel (see circle). Unlock the carrier of the front control panel (1) and remove it from the FSIOM (2). BX400 S1 Options Guide 33

34 ServerView Local Service Display for Blade Figure 16: Removing the front control panel from the carrier Remove the stopper from the carrier. To do this, loosen the screw (1) and push the stopper (2) out. Remove the front control panel from the carrier (3). Figure 17: Inserting the ServerView Local Service Display for Blade into the carrier Push the ServerView Local Service Display for Blade into the carrier and secure the stopper with the screw again. 34 Options Guide BX400 S1

35 ServerView Local Service Display for Blade Figure 18: Inserting the carrier into the FSIOM Push the carrier all the way to the stop into the FSIOM (1). In this position the lock engages (2). Disengage the locking mechanism of the ServerView Local Service Display for Blade (3) and slide it completely into the FSIOM. Figure 19: Inserting the carrier into the FSIOM Place the LCD cable in the cable reel (1). Connect the LCD cable (see circle). BX400 S1 Options Guide 35

36 ServerView Local Service Display for Blade Figure 20: Inserting the carrier into the FSIOM Push the FSIOM into the system unit until the security lock engages. Connect the SATA cable (see circle). Disengage the security lock of the FSIOM (1) and push it completely into the system unit (2). The FSIOM clicks into place in its final position. Reinstall server blades, storage blades or server blade dummy modules, see the Operating Manual. Connect the system unit to the power outlet, and switch it on as described in the chapter "Completion" on page Options Guide BX400 S1

37 7 Conversion from a rack model to a floorstand model V CAUTION! Follow the safety instructions in the chapter "Safety instructions" on page 13. The rack model can be optionally converted to floorstand model using a conversion kit. Make a note of the positions of the individual server blades and storage blades, the connection blades, power supply units, fan units and management blades in the system unit for reinstallation. Remove the server blades, storage blades, power supply units, fan units, connection blades and management blades from the system unit. For assembly instructions see the Operating Manual. Removing the ODD or ODD dummy module Figure 21: Removing the ODD Press the green engaging hook up (1) and to the front side of the system unit (2) to remove the ODD or the ODD dummy module. BX400 S1 Options Guide 37

38 Conversion from a rack model to a floorstand model Store the ODD or ODD dummy module in a safe place. You will need it for installing on the FSIOM later on. Removing the handles bars Figure 22: Removing the handle bars Loosen the four countersunk screws on either side to remove the handle bars. 38 Options Guide BX400 S1

39 Conversion from a rack model to a floorstand model Removing the ID card Figure 23: Pulling the ID card up to the stop Pull the ID card out of the system unit up to the stop. Figure 24: Removing the ID card Press the the engaging lug (1) as you pull the ID card out of the system unit (2). BX400 S1 Options Guide 39

40 Conversion from a rack model to a floorstand model Removing the FSIOM Figure 25: Disengaging the FSIOM Disengage the lock of the FSIOM (1) and pull it out of the system unit up to the stop (2) I If the FSIOM is hard to unlock, press it at the top front as you release it. 40 Options Guide BX400 S1

41 Conversion from a rack model to a floorstand model Figure 26: Removing the FSIOM Unplug the SATA cable (1). Unlock the FSIOM (2) and pull it out of the system unit completely. BX400 S1 Options Guide 41

42 Conversion from a rack model to a floorstand model Removing the SATA cable Detach the SATA cable from the cable guides inside the FSIOM bay (see arrows). Figure 27: Removing the SATA cable 42 Options Guide BX400 S1

43 Conversion from a rack model to a floorstand model Figure 28: Opening the cable channel Remove the cover above the cable channel on top of the system unit by loosening the two countersunk screws (see circles). Figure 29: Removing the SATA cable Detach the plug from the fixing pins (see circles). Detach the cable from the cable guides (see arrows). Carefully pull out the other end of the cable of the hole in the system unit. Store the cable in a safe place. You will need it for the connection of the ODD on the FSIOM later on. BX400 S1 Options Guide 43

44 Conversion from a rack model to a floorstand model Removing the front control panel Figure 30: Removing the front control panel from the FSIOM Unplug the LCD cable from the front control panel and from the FSIOM (see circles) and remove the LCD cable by detaching the cable clamp. Unlock the carrier of the front control panel (1) and remove it from the FSIOM (2). I Carrier, front control panel and LCD cable are no longer required. I When a ServerView Local Service Display for Blade is installed in your system unit, you must remove it in the same way as the front control panel. 44 Options Guide BX400 S1

45 Conversion from a rack model to a floorstand model Installing the ODD Figure 31: Inserting the ODD in the FSIOM Push the ODD into the bay of the FSIOM until the engaging hook (1) under the metal holder (2) locks in place. Figure 32: Connecting the SATA cable to the FSIOM Connect the bent plug of the SATA cable you obtained to the port on the system board (see circle). BX400 S1 Options Guide 45

46 Conversion from a rack model to a floorstand model Figure 33: Connecting the SATA cable to the ODD Connect the other plug of the SATA cable to the port on the ODD (see circle) and put the cable in the cable clamp (1). 46 Options Guide BX400 S1

47 Conversion from a rack model to a floorstand model Replacing the sidebars Turn the system unit through 90 to the right so that the bay of the FSIOM is on the bottom. V CAUTION! Get a second person to help you do this. The PRIMERGY BX400 S1 system unit is large and heavy. Figure 34: Removing the rack model sidebars Remove the sidebars of the rack variant by loosening four countersunk screws on both sides. Keep the screws for the fastening of the floorstand sidebars. BX400 S1 Options Guide 47

48 Conversion from a rack model to a floorstand model Figure 35: Attaching the floorstand sidebars Attach the floorstand sidebars with the countersunk screws you obtained with the removal of the sidebars of the rack model. 48 Options Guide BX400 S1

49 Conversion from a rack model to a floorstand model Securing the floor unit Figure 36: Fastening the floor unit Secure the floor unit on the underside with the six provided screws (see circles). V CAUTION! When fastening the four screws (see red circles), be careful that they do not fall into the hollow spaces of the castor support braces. Put the system unit through 180 in the upright position. V CAUTION! Get a second person to help you do this. The PRIMERGY BX400 S1 system unit is large and heavy. BX400 S1 Options Guide 49

50 Conversion from a rack model to a floorstand model Securing the top cover module Figure 37: Engaging hooks of the top cover module The top cover module is equipped with engaging hooks on both sides (see circles) for the anchoring on the housing of the system unit. Figure 38: Oblong holes in the housing of the system unit In the figure above, the oblong holes in the housing of the system unit for the application of the engaging hooks of the top cover module are indicated by circles. Place the top cover module on the housing of the system unit so that the engaging hooks interlock with the oblong holes on both sides. 50 Options Guide BX400 S1

51 Conversion from a rack model to a floorstand model Figure 39: Fastening the top cover module Push the top cover module backward as far as it will go. Secure the top cover module on both sides with countersunk screws (see circle). BX400 S1 Options Guide 51

52 Conversion from a rack model to a floorstand model Inserting the ID Card Figure 40: Inserting the ID card Insert the ID Card in the slot provided on the ServerView Local Service Display for Blade. Routing cables Figure 41: Routing the cables Thread the cables through the hole in the housing of the system unit (see arrow). 52 Options Guide BX400 S1

53 Conversion from a rack model to a floorstand model Figure 42: Routing the LCD cable Route the cables under the guides as shown in the figure (see arrows). Figure 43: Closing the cable channel Insert the slot cover above the cable channel and secure it with the two countersunk screws you obtained with the removal (see circles). BX400 S1 Options Guide 53

54 Conversion from a rack model to a floorstand model Installing the FSIOM Figure 44: Connecting the door sensor cable and the LCD cable to the FSIOM Push the FSIOM into the system unit until the security lock engages. Connect the door sensor cable (small circle) and the LCD cable (large circle) to the FSIOM. Disengage the security lock of the FSIOM (1) and push it completely into the system unit (2). The FSIOM clicks into place in its final position. 54 Options Guide BX400 S1

55 Conversion from a rack model to a floorstand model Securing the side covers Figure 45: Side cover fastening arrangements Place the left side cover on the three metal brackets (see arrows) and hook the side cover in the eight t-profile pins (see circles). BX400 S1 Options Guide 55

56 Conversion from a rack model to a floorstand model Figure 46: Fastening the side cover Push the side cover completely backward and secure it with the provided screw (see circle). Secure the right side cover in the same way. Reinstall the server blades, storage blades, power supply units, fan units, connection blades and management blades, see the Operating Manual. Connect the system unit to the power outlet, and switch it on as described in the chapter "Completion" on page Options Guide BX400 S1

57 8 Completion V CAUTION! Follow the safety instructions in the chapter "Safety instructions" on page Floorstand model Figure 47: Inserting the door Insert the hinge hole of the door (1) in the hinge pin (2). BX400 S1 Options Guide 57

58 Completion Figure 48: Positioning the door hinge pin Pull the hinge pin downward (1) and position it in the hinge hole in the cover plate (2). Insert the key. Lock the door. Connect all power plugs to the power outlets. Press the On/Off button to start up the system unit. 8.2 Rack model Connect all cables on the rear of the server. Connect all power plugs to the power outlets. Press the On/Off button to start up the system unit. 58 Options Guide BX400 S1

59 Index A accessible drives 9 C conversion of floorstand model to rack model 9, 37 D door sensor cable 27, 29 E electrostatic-sensitive devices (ESD) 20 F front control panel 31 Front-Side I/O Module (FSIOM) 33 I information, additional 8 L laser information 19 LCD cable 27, 29 light emitting diode (LED) 19 Local Service Display 9, 31 LSB 9, 31 M meaning of the symbols 9 N notational conventions 9 O ODD 23 ODD dummy module 27 optical disk drive 23 T target group 7 BX400 S1 Options Guide 59

60 Index 60 Options Guide BX400 S1