Speed switches Programmable, digital speed switch With incremental encoder HOG 10

Transcription

1 Features Freely programmable on and off switching speed Operation via included software (RS485 interface) Additional incremental signals (HTL/TTL) Combination with end shaft ø16 mm DSL.R: 3 outputs speed controlled (independent transistor outputs) DSL.E: 2 outputs speed controlled and 1 control output Optional Relay module DS 93 R (DSL.R version only) Technical data - electrical ratings Consumption w/o load 200 ma Resolution (steps/turn) Phase shift 90 ±20 Interface RS485 Scan ratio % Switching accuracy Switching delay time ±2 % (Digit) 40 ms Reference signal Zero pulse, width 90 Output circuit Output frequency Sensing method,, + inverted HTL (power linedriver) TTL (RS422) 120 khz Optical Interference immunity DIN EN Emitted interference DIN EN E Voltage supply Switching outputs Output switching capacity.r Voltage supply Switching outputs Output switching capacity VDC 2 outputs, speed control 1 control output VAC/VDC ma VDC 3 outputs, speed control 12 V High: ns 0 V Low: n ns 40 ma Technical data - mechanical design Dimensions (flange) Shaft ø105 mm Protection DIN EN IP 66 Speed (n) Range of switching speed (ns) Operating torque Rotor moment of inertia Shaft loading Materials ø16 mm end shaft 6000 rpm Resolution = 512: ± rpm Resolution = 1024: ± rpm Resolution = 2048: ± rpm Resolution = 2500: ± rpm 2 Ncm 340 gcm² 250 N axial 400 N radial Operating temperature C Housing: aluminium die-cast Shaft: stainless steel Resistance DIN EN Vibration 10 g, Hz DIN EN Shock 200 g, 6 ms Explosion protection Weight approx. Connection II3G Ex na T4 X (gas) II3D Ex td IP66 A22 T135 C X (dust) 3.1 kg Terminal box

2 Part number HOG 10 DN + DSL.E HOG 10 DN + DSL.R I R Incremental output Output circuit HTL with Output circuit TTL with I R Incremental output Output circuit HTL with Output circuit TTL with See part number (pulses) DN,, See part number (pulses) DN,, Part number (pulses) Accessories Adapter USB RS485 Connectors and cables HEK 8 Sensor cable for encoders Mounting accessories ET x Torque support size M6 Diagnostic accessories HENQ 1100 Analyzer for encoders Relay module for.r DS 93 R Relay modul

3 at positive rotating direction Terminal assignment View A - Connecting terminal in terminal box zero pulse zero pulse 90 (GND) +UB Terminal significance Speed switch version DSL.R R1* Transistor switching output 1, R2* Transistor switching output 2, R3* Transistor switching output 3, GND* Ground connection Interface for PC or Laptop (adapter required). Operation of the DSL via the included software. * Connection to relay module, for example DS 93 R (accessory) Speed switch version DSL.E R1 (A+B) Electronic relay output 1, V AC/DC R2 (A+B) Electronic relay output 2, V AC/DC C1 (A+B) Electronic relay output as a control output, ma Interface for PC or Laptop (adapter required). Operation of the DSL via the included software. View B - Connecting terminal speed switch Version DSL.R R1 R2 R3 GND View B - Connecting terminal speed switch Version DSL.E R1 R2 C1

4 Block circuit diagram Version with DSL.E C1-A VDC Control C1-B R1-A R1-B Encoder DSL.E R2-A R2-B A, B RS485 (PC/Laptop) Version with DSL.R VDC High = 12 V Low = 0 V R1 12 VDC (High) Manner of output circuit Encoder DSL.R R2 R3 A, B RS485 (PC/Laptop) R1, R2, R3 (Low) -n +n -ns (off) -ns (on) 0 +ns (on) +ns (off) n = speed ns (on) = adjusted switching on speed ns (off) = adjusted switching off speed

5 Dimensions Drawing 90 rotated a/f A B M20x1.5 M20x1.5 Accessory Positive rotating direction HM05M26992