The '97 Handbook Adapters

Transcription

1 The '97 Handbook Adapters

2 Spectrum Electrotechnik GmbH is a leading manufacturer of RF and Microwave Components in the Range of DC to 50 GHz. The products are published in eight individual catalogs, showing detailed information and comprehensive data. Adapters, DC 50 GHz, 50 Ohms Coaxial Adapters (In Series and Between Series) High Power Adapters PushOn Adapters Waveguide to Coax Adapters, DC 50 GHz, 50 Ohms Blind Mate Coaxial High Power Multi Pin PushOn Cable Assemblies, DC 50 GHz, 50 Ohms ANA Test Cables Flexible Cable Assemblies Low Loss Cable Assemblies Phase Stable Cable Assemblies Semi Rigid Cable Assemblies (Dia. 0.34" to 1") Test Necessities and Accessories, DC 50 GHz, 50 Ohms LRL, TRL Calibration and Verification Kits ANA Cable Assemblies Torque Wrenches Interface Gauges Calibration Kits Terminations Components, DC 50 GHz, 50 Ohms Antennas Attenuators Circulators CDMComponents Couplers Custom Components DCBlocks GainEqualizers Isolators Limiters Mismatches Phase Shifters Switches Terminations Waveguide Components Quick Connections, 50 Ohms Blind Mate Push On Adapters Push On Push On Cable Assemblies Components, 75 Ohms Adapters Attenuators Switches Transformers Machines and Tools Coax Cable Cutting/Stripping Machines Flex Cable Cutting/Stripping Machines SemiRigid Cable Bending Machines Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) E Mail: CompuServe.com Fax (89) (Country Code: 49)

3 111a.pm5 Contents Page No. This Handbook shows a most extensive Company Profile... 4 line of Microwave Adapters in the Ordering Information... 5 frequency range of DC to 50 Ghz. Adapter Cross Reference Table... 6 On pages 6 to 7 you will find an Adapter Adapters Series 1.4/ Cross Reference Table which shows the availability of the Adapters within or Adapters Series 1.8/ between the connector series. It will direct Adapters Series 2/ you to the appropriate section of this catalog. Adapters Series 2.4 mm Adapters Series 3.5 mm The Table of Contents to the right will identify the individual sections that are Adapters Series 7 mm shown in this Handbook. Each section is Adapters Series 7/ headed by a reference table, indicating to you the contents of the section or guiding Push On 7/ you to other related divisions, specification Handling Information sheets, showing the electrical, mechanical and environmental performance of the Adapters Series BMA particular connector series and their Adapters Series BNC interface dimensions. You will obtain details on a most complete line of adapters. Adapters Series C Adapters Series HN But just in case you still do not find exactly the product you require, please Adapters Series K* contact the factory or your nearest Spectrum Area Representative. Due to continuous development we may have solved a similar problem for someone else, or did develop already the product you require. If you know the Part Number of the product you would like to find more information about, please refer to the Part Number Index located in the last section of this Handbook. As it is our main goal to improve specification and performance of the products, Spectrum Electrotechnik GmbH has to reserve the right to change specifications, Adapters Series N... Push On N... Handling Information... Adapters Series SBX... Adapters Series SBY... Adapters Series SC... Adapters Series SMA... Push On SMA... Handling Information... Adapters Series SMP... Adapters Series SPM design and any other information shown in Adapters Series TNC this Handbook at any time without previous notice. Push On TNC Handling Information Because of the comprehensive information gathered in this volume, we call it a Adapters Series TNX Handbook, hopefully the Handbook you Adapter Sets like to work with best. If you find the time, we would appreciate your personal Waveguide to Coax Adapters opinion about this Handbook. * 'K' Connector is a trademark of Wiltron Company. Waveguide Flanges... Part Number Index... Sales Representatives Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 3

4 The Company Spectrum Electrotechnik GmbH was founded in 1981 and has become a leading supplier of stateoftheart components used in the RF and Microwave Technology, such as, Adapters, Cable Assemblies, Phase Shifters, Couplers, Gain Amplitude Equalizers, Terminations, Calibration Kits, etc., etc. In Addition, a number of complex and integrated components have been engineered and manufactured for certain programs and to the customer needs. Throughout the world, Spectrum Electrotechnik GmbH has established a reputation as a design, development and manufacturing center. The Company has been recognized as setting standards, introducing new ideas and leading into new technologies. The Products The products are used in commercial systems such as Cellular Applications, Radios, SatCom/VSAT, Satellites and Space Applications, Test Centers and Wireless Communication. The Products are used in defence applications as well, like Airborne Radars, Electronic Intelligence, Electronic Warfare, Jamming Systems, Missile Guidance, etc. Whenever RF or Microwave Expertise and Advanced Manufacturing Technologies are needed you will find Spectrum Electrotechnik GmbH. Capabilities and Facilities The departments within the Company have been set up as an intelligent Network, guaranteeing complete inhouse control of every operation and procedure, from design, development, manufacturing, assembly and testing. Spectrum Electrotechnik GmbH is small enough to react quickly and large enough to handle extensive orders of important programs successfully. This capability enables to develop, manufacture and test the extensive range of Products meeting the highest standards of quality and performance. Spectrum Electrotechnik GmbH introduced CAD design centers already in 1984 as well as CAD/CAM work stations to provide data to computer controlled machines. The Company operates the most advanced machines and uses Test Centers to 50 GHz from HP and to 40 GHz from Wiltron. Manufacturing and Quality Control comply to DINISO 9000, permitting to meet strict requirements in Commercial, Avionics, Military and HiRel appplications. A Final Inspection to 100% is standard, Tests on electrical and physical performance, their tolerances, the workmanship, and the compliance to applicable specifications. Support An adequate and knowledgeable staff is always available to support the Customers in respect to Applications, Engineering and Sales. The staff acts as a Team, understanding applications, specifications, needs, priorities and problems as well. A net of distributors assures immediate delivery of off the shelf products. Authorized technical knowledgeable Representatives will provide immediate assistance to the customers needs. 4 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 111a.pm5

5 Ordering Information Ordering Please include both, Spectrum Elektrotechnik GmbH part number, and a description of the item(s) ordered. If special features are required, describe them as completely as possible and include an engineering sketch. Orders may be placed directly with the factory in Munich or with any authorized Spectrum Elektrotechnik GmbH Representative. Minimum Factory Order is DM Acceptance of Orders All orders are subject to acceptance at the discretion of the factory and with an Order Acknowledgment from Spectrum Elektrotechnik GmbH. Terms Upon approval of credit, payment is due Net 30 days from date of invoice. Late payments are subject to a 1.5 % monthly charge on past due balances. Shipments Spectrum Elektrotechnik GmbH ships via the most expedient reliable carrier. Shipment F.O.B., Spectrum Elektrotechnik GmbH plant, will be sent freight prepaid and billed unless other prior arrangements are made. Spectrum Elektrotechnik GmbH will use any acceptable method of delivery specifically requested by customer. Damaged Materials/Shortages All orders should be inspected upon receipt for both completeness and to insure receipt of materials in proper condition. All claims for shortages must be made within thirty (30) days after date of shipment of material from Spectrum Elektrotechnik GmbH plant. Title to goods passes to the Buyer upon delivery to the carrier and risk of loss or damage shall thereafter rest with the Buyer. Claims for damage or loss while material is in transit must be made against the carrier by the Buyer. Cancellation Cancellation of, or changes to an order acknowledged by Spectrum Elektrotechnik GmbH are accepted only upon terms that protect Spectrum Elektrotechnik GmbH against loss. Returns Excess or unused material cannot be returned for credit without factory authorization. Such material is subject to a handling charge of not less than 15 % upon return and inspection of material at the factory. In no case will Spectrum Elektrotechnik GmbH authorize return of material beyond ninety (90) days after shipment from the factory. Credit for returned material is issued by Spectrum Elektrotechnik GmbH only to the original purchaser. Freight charges for returned material is the responsibility of the Buyer. Defective Material Claims for defective material or workmanship are subject to verification by Spectrum Elektrotechnik GmbH Quality Control, and must have prior factory authorization. Upon verification, Spectrum Elektrotechnik GmbH reserves the right to repair or replace, as deemed necessary. Prices / Specifications Unless otherwise specified, prices quoted are F. O. B. Spectrum Elektrotechnik GmbH plant. Both prices and specifications are subject to modification without prior notice. Patent and Trademark Indemnity Buyer agrees at Buyer's expense to protect and defend Seller against any and all claims of patent or trademark infringement arising from Seller' s compliance with Buyer's designs or specifications or instruction and to hold Seller harmless from all losses, damages, costs and expenses attributable to any such claim or claims. Seller shall have the right to approve or disapprove counsel designated by Buyer to defend such claims. 1order.pm5 Warranty Spectrum Elektrotechnik GmbH warrants products of its manufacture to be free from defects in material and workmanship under conditions of normal use. If, within one year after delivery of the original owner and after prepaid return by the original owner, any Spectrum Elektrotechnik GmbH product is found to be defective, Spectrum Elektrotechnik GmbH shall, at its option, repair or replace said defective item. This warranty does not apply to products which have been disassembled, modified or subjected to conditions exceeding the applicable specifications or ratings. Spectrum Elektrotechnik GmbH reserves the right to make design changes without notice on any of its products and without any obligation to make same or similar changes to items previously purchased. In no event does Spectrum Elektrotechnik GmbH assume liability for installation labor or for consequential damages. This warranty is the extent of the obligation or liability assumed by Spectrum Elektrotechnik GmbH with respect to its products, and no other warranty or guarantee is either expressed or implied. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 5

6 1chart.pm / /5.6 2/ mm Page mm 7 mm 7 / 16 BMA BNC C HN K* N SBX SBY SC SMA SMP SPM TNC TNX Pages Page 37 Pages Pages Pages Pages Pages Pages Pages Page 32 BetweenSeries and InSeries Page 20, 37 Page 37 Pages Page 36 Page 40 Page 41 Page 42 Page 40 Page 43 Page 44 Page 45 Page 46 Pages Pages 51, 97 Page 118 Page mm 3.5 mm 7 mm 7/16 BMA BNC C K* Page 98 Page 56, 135 Pages 16, 61 Page 60 Pages 62, 99 Page 136 Page 161 Adapter Cross Page 40 Page 66, 100 Pages Pages Page 41 Pages Pages Pages * 'K' Connector is a trademark of Wiltron Company

7 Reference Table Pages 12, 92 Pages Pages Page 42 Pages 51, 97 Page 98 Page 62, 99 Page 66, 100 Page 70, 101 Pages Page Page 104 Page 105 Page 106, 126 Pages 87, Pages 87, , 157 Page 114 Page 118 Page 104 Page 137 Page 122 Page 105 Page 138 Page 43 Page 56, 135 Page 136 Pages 87, Page 137 Page 138 Pages Page 139, 150 Page 140, 157 Page Ohms N SBX SBY SMA SMP SPM TNC TNX Page 44 Pages Page 146 Page 139, / /5.6 2/ mm 3.5 mm 7 mm 7 / 16 BMA BNC HN SMA SMP SPM TNC TNX Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 7 Page 45 Page 161 Pages 87, , 157 Page 140, 157 Pages Page 32 Page 46 Page 114 Page 141 Page 166 C K* N SBX SBY SC

8 Adapters 1.4 / 4.4 BetweenSeries Adapters 1.4 / 4.4 If your choice of 1.4/4.4 Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 1.4/4.4 N Page 12 "1.4/4.4" In Series Adapters available on request b.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 9

9 1.4/4.4 Specifications to DIN The specifications below are general specifications for all 1.4/4.4 connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications DIN 47298, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.3 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 20.0 GHz min. The insulation resistance shall not be less than 10,000 megohms * f (GHz) The center contact resistance drop shall not exceed 8.0 milliohms and the outer contact resistance drop shall not exceed 0.5 milliohms. The magnitude of the test voltage shall be 1,000 volts rms at sea level. RF High Potential Withstanding Voltage is not applicable. RF Leakage is not applicable. Insertion Loss is not applicable. The connector is to be tested and its mating connector shall be subjected to 100 insertions min.. Withdrawal cycles / minute are not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements pounds (250 N) min. Not applicable for Female connectors. For male connectors, the axial force is 56.2 lbs (250 N) max.. The torque is 4.43 inchpounds (0.5 Nm) max. The torque required to engage and disengage shall not exceed 4.43 inchpounds (0.5 Nm). Longitudinal force is 1.79 lbs (8.0 N) max. See interface dimensions shown on next page. Applicable to Females only: oversize pin.0364 inch (.92 mm) max. dia.,.0787 inch (2.0 mm) deep; max. insertion force with min. dia. pin is not applicable; withdrawal force 2.82 oz (0.78 N) min. with.0354 inch (0.9 mm) max. dia. pin inchpounds (1.5 Nm) Specification DIN Part 4. Specification DIN IEC 68 Part 2 6. Specification DIN Part 7. Specification DIN Part 4. Moisture Resistance Moisture Resistance not applicable. Corona Level Specification DIN Part 3 (Section 9). 10 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 114inter.pm5

10 Interface Mating Dimensions (Per DIN 47298) 1.4/ inter.pm5 11

11 Between Series Adapters to Type 1.4 / 4.4 Part No /4.4 to NFem. DC 18.0 GHz x f (GHz) Part No /4.4 to NFem. DC 18.0 GHz x f (GHz) Part No /4.4 to NMale DC 18.0 GHz x f (GHz) Part No /4.4 to NMale DC 18.0 GHz x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 12 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 114pu.pm5

12 Adapters 1.8/5.6 BetweenSeries Adapters 1.8/5.6 If your choice of 1.8/5.6 Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 1.8/5.6 BNC Page 16 "1.8/5.6" In Series Adapters available on request b.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 13

13 1.8/5.6 Specifications to DIN The specifications below are general specifications for all 1.8/5.6 connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications DIN 47226, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 10.0 GHz min. The insulation resistance shall not be less than 10,000 megohms * f (GHz) The center contact resistance drop shall not exceed 4.0 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,000 volts rms at sea level. RF high potential withstanding voltage is is not applicable. Leakage is not applicable. (100 f (GHz)) db Insertion Loss is not applicable. The connector is to be tested and its mating connector shall be subjected to 500 insertions min. Withdrawal cycles / minute are not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. Cable Retention Force is not applicable. Coupling Nut Retention Force is not applicable. Force to Engage and Disengage is not applicable. Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin dia., insertion depth, insertion force with min. dia. pin are not applicable; withdrawal force 1.79 oz (.498 N) min. with.382 inch (9.7 mm) max. dia. pin. Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 14 Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 200 volts rms and the altitude is 65,600 feet (20 Km.). Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: inter.pm5

14 Interface Mating Dimensions (Per DIN 47226) 1.8/ / 5.6 Female 1.8 / 5.6 Male Form C 118inter.pm5 Form A Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 15

15 BetweenSeries Adapters to Type BNC Part No /5.6F to BNCF DC 4.0 GHz x f (GHz) Part No /5.6F to BNCM DC 4.0 GHz x f (GHz) Part No /5.6M to BNCF DC 4.0 GHz x f (GHz) Part No /5.6M to BNCM DC 4.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) x f (GHz) 118b.pm5

16 Adapters 2/5.5 BetweenSeries Adapters 2/5.5 If your choice of 2/5.5 Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 2/5.5 7 mm Page 20 "2/5.5" In Series Adapters available on request. 1255B.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17

17 2/5.5 Specifications The specifications below are general specifications for all 2/5.5 connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 14.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.5 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,500 volts rms at sea level. The RF high potential withstanding voltage is 1,000 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertions and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. Cable Retention Force is not applicable. Coupling Nut Retention Force is not applicable. Force to engage and disengage is not applicable. Longitudinal force is not applicable. Mating Characteristics are not applicable Recommended Mating Torque is not applicable. ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 18 Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Not applicable. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: int.pm5

18 Interface Mating Dimensions 2/5.5 2/5.5 Female : DC 14.0 GHz min. 2/5.5 Male 1255int.pm5 : DC 14.0 GHz min. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 19

19 BetweenSeries Adapters to Type 2/5.5 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: F296 Part No. F290 2/5.5 F to 7mm DC 14.0 GHz x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) b.pm5

20 Adapters 2.4 mm InSeries and BetweenSeries Adapters 2.4 mm If your choice of 2.4 mm Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 2.4 mm 2.4 mm Page mm 7 mm Please refer to 3.5 mm BetweenSeries Adapters Please refer to 7 mm BetweenSeries Adapters Pages Page 37 K* N Please refer to K* BetweenSeries Adapters Please refer to N BetweenSeries Adapters Pages Pages mmb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. * 'K' Connector is a trademark of Wiltron Company. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 21

21 2.4 mm Specifications The specifications below are general specifications for all 2.4 mm connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of.00005inch in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 50.0 GHz min. Insulation Resistance is not applicable. Voltage Standing Wave Ratio is not applicable. The center contact resistance drop shall not exceed 1.5 milliohms and the outer contact resistance drop shall not exceed 0.8 milliohms. The magnitude of the test voltage shall be 1,200 volts rms at sea level. The RF high potential withstanding voltage is 400 volts rms at 5 MHz. Leakage is not applicable. (100 f (GHz)) db Insertion Loss is not applicable. The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 60 pounds (267 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 15 inchpounds (1.7 Nm) max. The torque required to engage and disengage shall not exceed 2 inchpounds (0.226 Nm). Longitudinal force is not applicable. Mating Characteristics are not applicable inchpounds ( Nm) ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 22 Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 150 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: inter.pm5

22 Interface Mating Dimensions 2.4 mm 2.4 mm Female 124inter.pm5 2.4 mm Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 23

23 InSeries Adapters to Type 2.4 mm Part No. HFHF 2.4mmF to 2.4mmF DC 50.0 GHz 1.20 : 1 Part No. Part No. HFH2 2.4mmF to 2.4mmF DC 50.0 GHz 1.20 : 1 HFHM 2.4mmF to 2.4mmM DC 50.0 GHz 1.20 : 1 for direct connection with HP8510 Part No. HMHM 2.4mmM to 2.4mmM DC 50.0 GHz 1.20 : 1 Part No. HMH2 2.4mmM to 2.4mmF DC 50.0 GHz for direct connection with HP8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section : 1 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 124mmin.pm5

24 Adapters 3.5 mm InSeries and BetweenSeries Adapters 3.5 mm If your choice of 3.5 mm Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 3.5 mm 2.4 mm 3.5 mm 7 mm K* N TNX Please refer to 7 mm BetweenSeries Adapters Please refer to K* BetweenSeries Adapters Please refer to N BetweenSeries Adapters Pages Pages Pages Pages Pages Page mm.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. * 'K' Connector is a trademark of Wiltron Company. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 25

25 3.5 mm Specifications The specifications below are general specifications for all 3.5 mm connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Centre Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 35.0 GHz min. The insulation resistance is not applicable * f (GHz) The center contact resistance drop shall not exceed 2.0 milliohms and the outer contact resistance drop shall not exceed 0.4 milliohms. The magnitude of the test voltage shall be 1,500 volts rms at sea level. The RF high potential withstanding voltage is 500 volts rms at 5 MHz. Leakage is not applicable. (100 f (GHz)) db (.5 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 1000 insertions and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 60 pounds (267 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 15 inchpounds (1.7 Nm) max. The torque required to engage and disengage shall not exceed 2 inchpounds (0.226 Nm). Longitudinal force is not applicable. Mating Characteristics are not applicable inchpounds ( Nm) ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 26 Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition D. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The Corona Level is not applicable. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: inter.pm5

26 Interface Mating Dimensions 3.5 mm 3.5 mm Female 135inter.pm5 3.5 mm Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 27

27 InSeries Adapters to Type 3.5 mm Part No mmF to 3.5mmF DC 26.5 GHz 1.15 : 1 Part No mmF to 3.5mmF DC 35.0 GHz 1.15 : 1 Part No. Part No. H mmF to 3.5mmF DC 26.5 GHz 1.15 : 1 80H mmF to 3.5mmF DC 35.0 GHz 1.15 : 1 for direct connection with HP8510 for direct connection with HP8510 Part No. 3.5mmF to 3.5mmM DC 26.5 GHz 1.15 : 1 for direct connection with HP8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 28 H mmin.pm5

28 InSeries Adapters to Type 3.5mm for direct connection with HP8510 Part No. Part No. 80H mmF to 3.5mmM DC 35.0 GHz 1.15 : mmM to 3.5mmF DC 26.5 GHz 1.15 : 1 Part No mmM to 3.5mmF DC 35.0 GHz 1.15 : 1 Part No mmM to 3.5mmM DC 26.5 GHz 1.15 : 1 Part No mmM to 3.5mmM DC 35.0 GHz 135mmin.pm : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 29

29 BetweenSeries Adapters to Type 3.5 mm Part No. H mmF to 3.5mmF DC 35.0 GHz 1.15 : 1 for direct connection with HP8510 Part No. H mmF to 3.5mmM DC 35.0 GHz 1.15 : 1 for direct connection with HP8510 Part No. HF92 2.4mmF to3.5mmf DC 35.0 GHz 1.15 : 1 Part No. HF91 2.4mmF to3.5mmm DC 35.0 GHz 1.15 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 30 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 135mmb.pm5

30 BetweenSeries Adapters to Type 3.5 mm Part No. HM92 2.4mmM to3.5mmf DC 35.0 GHz 1.15 : 1 Part No. HM91 2.4mmM to3.5mmm DC 35.0 GHz 1.15 : 1 for direct connection with HP8510 Part No. HMH3 2.4mmM to3.5mmf DC 35.0 GHz 1.15 : 1 Part No. HFH3 2.4mmF to3.5mmf DC 35.0 GHz 135mmb.pm : 1 for direct connection with HP8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 31

31 BetweenSeries Adapters to Type 3.5 mm Part No TNXF to 3.5mmF DC 18.0 GHz Part No TNXF to 3.5mmM DC 18.0 GHz Part No TNXM to 3.5mmF DC 18.0 GHz Part No TNXM to 3.5mmM DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 32 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 135mmb.pm5

32 Adapters 7 mm InSeries and BetweenSeries Adapters 7 mm If your choice of 7 mm Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 2/ mm 3.5 mm 7 mm C K* N SC SMA SMP TNC TNX 7 mm Page 37 Page 37 Pages Page 36 Page 40 Page 41 Page 42 Page 40 Page 43 Page 44 Page 45 Page 46 17mm.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 33

33 7 mm Specifications to IEC 4572 The specifications below are general specifications for all 7 mm connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications IEC 4572, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 18.0 GHz min. The insulation resistance is not applicable * f (GHz) The center contact resistance drop shall not exceed 1.0 milliohms and the outer contact resistance drop shall not exceed 0.1 milliohms. The magnitude of the test voltage shall be 2,500 volts rms at sea level. The RF high potential withstanding voltage is 1,000 volts rms at 5 MHz. Leakage is not applicable. (120 f (GHz)) db (.007 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 5000 insertions. Withdrawal cycles not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. Cable Retention Force is not applicable. Coupling Nut Retention Force is not applicable. Force to Engage and Disengage is not applicable. Longitudinal force is not applicable. Mating Characteristics are not applicable inchpounds ( Nm) ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 34 Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Corona Level is not applicable. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: mmint.pm5

34 Interface Mating Dimensions (Per IEC 4572) 7 mm 17mmint.pm5 35

35 InSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No mm to 7mm DC 18.0 GHz 1.06 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 36 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17mmb1.pm5

36 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: HF96 Part No. HF90 2.4mmF to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: H296 Part No. H mmF to 7mm DC 18.0 GHz for direct connection with HP : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: HM96 Part No. HM90 2.4mmM to 7mm DC 18.0 GHz 1.06 : 1 17mmb1.pm5 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: F296 Part No. F290 2/5.5F to 7mm DC 14.0 GHz x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 37

37 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 9296 Part No mmF to 7mm DC 18.0 GHz 1.15 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No mmF to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No mmF to 7mm DC 18.0 GHz 1.06 : " 32.2mm Part No. H mmF to 7mm DC 18.0 GHz 1.06 : 1 for direct connection with HP8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 38 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: H396 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17mmb1.pm5

38 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 9196 Part No mmM to 7mm DC 18.0 GHz 1.15 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No mmM to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No mmM to 7mm DC 18.0 GHz 1.06 : 1 17mmb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 39

39 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 8996 Part No CFemale to 7mm DC 10.0 GHz x f (GHz) The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 8896 Part No CMale to 7mm DC 10.0 GHz x f (GHz) The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 7996 Part No SCFemale to 7mm DC 10.0 GHz x f (GHz) Part No SCMale to 7mm DC 10.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 40 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17mmb1.pm5

40 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: KF96 Part No. KF90 * KFemale to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: KM96 Part No. KM90 * KMale to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: WI96 Part No. WI90 * KFemale to 7mm DC 18.0 GHz for direct connection with Wiltron : 1 17mmb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 41

41 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 6196 Part No NFemale to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No NFemale to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 5196 Part No NMale to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No NMale to 7mm DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section : 1 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17mmb1.pm5

42 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 2196 Part No SMAF to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No SMAF to 7mm DC 18.0 GHz 1.06 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 1196 Part No SMAM to 7mm DC 18.0 GHz 1.06 : 1 17mmb1.pm5 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No SMAM to 7mm DC 18.0 GHz 1.06 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 43

43 BetweenSeries Adapters to Type 7 mm Part No. Part No. Part No. Part No. Part No. MP90 SMPF to 7mm DC 18.0 GHz 1.10 : 1 MJ90 SMPM to 7mm DC 18.0 GHz 80MJ90 SMPM to 7mm DC 18.0 GHz 8003MJ90 SMPM to 7mm DC 18.0 GHz 8004MJ90 SMPM to 7mm DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 44 If you require 6 slots at the 7mm Center Conductor, the Part Number will become: MP96 If you require 6 slots at the 7mm Center Conductor, the Part Number will become: MJ96 If you require 6 slots at the 7mm Center Conductor, the Part Number will become: 80 MJ : : 1 If you require 6 slots at the 7mm Center Conductor, the Part Number will become: 8003 MJ : 1 If you require 6 slots at the 7mm Center Conductor, the Part Number will become: 8004 MJ : 1 Full detent Limited detent Smooth bore 17mmb1.pm5

44 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No TNCF to 7mm DC 18.0 GHz 1.10 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No TNCM to 7mm DC 15.0 GHz 1.10 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: Part No TNCM to 7mm DC 18.0 GHz 1.10 : 1 17mmb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 45

45 BetweenSeries Adapters to Type 7 mm The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 4996 Part No TNXF to 7mm DC 18.0 GHz 1.10 : 1 The Center Conductor of the 7 mm Connector is supplied with 4 slots. If you require 6 slots, Part Number changes to: 3996 Part No TNXM to 7mm DC 18.0 GHz 1.10 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 46 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17mmb1.pm5

46 Adapters 7/16 InSeries and BetweenSeries Adapters 7/16 If your choice of 7/16 Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. 7/16 7/16 7/16 N SBX The PUSHON The PUSHON Please refer to SBX BetweenSeries Adapters Page 51 Page 52 Page 51 Page 118 SBY Please refer to SBY BetweenSeries Adapters Page /16b.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 47

47 7/16 Specifications to DIN The specifications below are general specifications for all 7/16 connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications DIN 47223, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 7.5 GHz min. The insulation resistance shall not be less than megohms * f (GHz) The center contact resistance drop shall not exceed 0,8 milliohms and the outer contact resistance drop shall not exceed 1.5 milliohms. The magnitude of the test voltage shall be volts rms at sea level. The RF high potential withstanding voltage is 4,000 volts rms at 5 MHz. Leakage is not applicable. RF Leakage is not applicable (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion min. Withdrawal cycles / minute are not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 56,2 pounds (250 N) min. Not applicable for Female connectors. For male connectors, the axial force is 22.5 lbs (100 N) max.. The torque is 221 inchpounds (25 Nm) max. The Force to Engage and Disengage is not applicable. Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.2008 inch (5.10 mm) max. dia.,.177 inch (4.50 mm) deep; insertion force max. with min. dia. pin is not applicable; withdrawal force 2.16 oz (.6 N) min. with.1953 inch (4.96 mm) max. dia. pin. Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 48 Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 2800 volts rms and the altitude is 0 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: /16int.pm5

48 Interface Mating Dimensions (Per DIN 47223) 7 / 16 7 / 16 Female 17/16int.pm5 7 / 16 Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 49

49 Lockable Push On Connector of Type 7 / 16 The PushOn 'Connector Saver' was developed to eliminate the time consuming lightening, torquing and loosening of 7/16 connectors during test. The standard 7/16 female end engages the 7/16 male of the cable assembly, while the PushOn end of the adapter slides directly onto any 7/16 female, allowing quick connecting and disconnecting. Its mechanism locks safely onto the standard 7/16typethread: M29x1.5. Connector Saver PushOn 7/16 Safe Locking Mechanism Repeatable Performance Features Reduced Test Times Low Return Loss DC 7.5 GHz Long Life 50 Specifications: Electrical: Impedance 50 Ohms nominal Range DC to 7.5 GHz Max. VSWR 1.10 : 1 Insertion Loss 0.15 db max. at 7.5 GHz Contact Resistance 1.0 milliohms max. RF Leackage 90 db max. to 3.0 GHz 80 db max. to 7.5 GHz Diel. Withstdg. Voltage 3000 VRMS, 60 Hz RF High Potential Mhz Corona Level Voltage ft. Mechanical: Temperature Rating 55 C to +155 C Durability 500 mating cycles min. Materials: Body Stainless Steel Center Contact Beryllium Copper Outer Conductor Stainless Steel Finish: Center Contact Gold Plate per MILG45204, type II, class I, grade C. Body Passivate per QQP35 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 17/16in.pm5

50 PushOn Adapters of Type 7 / 16 7/16 PUSHON Part No. 7S76 7/16Push to 7/16F DC 7.5 GHz 1.10 : 1 7/16 PUSHON Part No. 7S61 7/16Push to NF DC 7.5 GHz 1.10 : 1 17/16in.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 51

51 InSeries Adapters Type 7 / 16 Part No /16F to 7/16F DC 7.5 GHz Part No /16M to 7/16F DC 7.5 GHz Part No /16M to 7/16M DC 7.5 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 52 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: in.pm5

52 Adapters BMA InSeries and BetweenSeries Adapters BMA If your choice of BMA Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. BMA N Please refer to N BetweenSeries Adapters Page 98 SMA Page 56 1bmab.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 53

53 BMA Specifications The specifications below are general specifications for all BMA connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 54 GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 22.0 GHz min. The insulation resistance shall not be less than megohms * f (GHz) The center contact resistance drop shall not exceed 2.0 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be volts rms at sea level. The RF high potential withstanding voltage is volts rms at 5 MHz. Leakage is not applicable. RF Leakage is not applicable (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion min. Withdrawal cycles / minute are not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 6 pounds (26.7 N) min. Not applicable for Female connectors. For male connectors, the axial force is 6 lbs (26,7 N) max. The torque required to engage shall not exceed 3 lbs. (13.4 N). The disengage force shall not exceed 1.5 lbs. (6.7 N) max. See interface dimensions shown on next page. Applicable to Females only: oversize pin.0373 inch (0.09 mm) max. dia.,.045inch (1.15 mm) deep; insertion force max. with min. dia. pin is not applicable; withdrawal force 1.0 oz (2.8 N) min. with.0355 inch (0.9 mm) max. dia. pin. Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition D. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 335 volts rms and the altitude is feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: bmaint.pm5

54 Interface Mating Dimensions BMA BMA Female : DC 22.0 GHz min. BMA Male 1bmaint.pm5 : DC 22.0 GHz min. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 55

55 BetweenSeries Adapters to Type BMA Part No. BW21 BMAF to SMAF DC 18.0 GHz Part No. BW11 BMAF to SMAM DC 18.0 GHz Part No. BM21 BMAM to SMAF DC 18.0 GHz Part No. BM11 BMAM to SMAM DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 56 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1bmabe.pm5

56 Adapters BNC InSeries and BetweenSeries Adapters BNC If your choice of BNC Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. BNC 1.8/5.6 BNC N SMA TNC Please refer to SMA BetweenSeries Adapters Please refer to TNC BetweenSeries Adapters Page 61 Page 60 Page 62 Page 136 Page 161 1bnc.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 57

57 BNC Specifications to MILC39012 (IEC 1698) The specifications below are general specifications for all BNC connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC39012, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 58 REQUIREMENT PARAGRAPH GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 4.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.5 milliohms and the outer contact resistance drop shall not exceed 1.0 milliohms. The magnitude of the test voltage shall be 1,500 volts rms at sea level. The RF high potential withstanding voltage is 1,000 volts rms at 5 MHz. Leakage is not applicable. (60 f (GHz)) db (.1 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 40 pounds (178 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The max. torque is not applicable. The torque required to engage and disengage shall not exceed 2.5 inchpounds (0.282 Nm). Longitudinal force is 3 lbs. (13.3 N) See interface dimensions shown on next page. Applicable to Females only: oversize pin.055 inch (1.4 mm) max. dia.,.080 inch (2.03 mm) deep; insertion force 2 lbs. (8.9 N) max. with.054 inch (1.37 mm) min. dia. pin; withdrawal force 2.00 oz (.556 N) min. with.052 inch (1.32 mm) max. dia. pin. Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition G. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 375 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: bncint.pm5

58 Interface Mating Dimensions (Per MILC39012 (IEC 1698)) BNC BNC Female 1bncint.pm5 BNC Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 59

59 InSeries Adapters to Type BNC Part No BNCF to BNCF DC 4.0 GHz x f (GHz) Part No. Part No BNCF to BNCF DC 4.0 GHz x f (GHz) 4Hole Flange BNCF to BNCF DC 4.0 GHz x f (GHz) Part No BNCM to BNCF DC 4.0 GHz x f (GHz) Part No BNCM to BNCM DC 4.0 GHz x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 60 1bncin.pm5

60 BetweenSeries Adapters to Type BNC Part No /5.6F to BNCF DC 4.0 GHz x f (GHz) Part No /5.6F to BNCM DC 4.0 GHz x f (GHz) Part No /5.6M to BNCF DC 4.0 GHz x f (GHz) Part No /5.6M to BNCM DC 4.0 GHz 1bncb.pm x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 61

61 BetweenSeries Adapters to Type BNC Part No BNCFem. to NFem. DC 4.0 GHz x f (GHz) Part No BNCMale to NFem. DC 4.0 GHz x f (GHz) Part No BNCFem. to NMale DC 4.0 GHz x f (GHz) Part No BNCMale to NMale DC 4.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1bncb.pm5

62 Adapters C BetweenSeries Adapters C If your choice of C Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. C N Page 66 "C" In Series Adapters available on request. 1cb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 63

63 C Specifications to MILC39012 (IEC 1697) The specifications below are general specifications for all C connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC39012, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 64 REQUIREMENT PARAGRAPH GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Centre Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 10.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.0 milliohms and the outer contact resistance drop shall not exceed 0.35 milliohms. The magnitude of the test voltage shall be 3,000 volts rms at sea level. The RF high potential withstanding voltage is 2,500 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 90 pounds (400 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The max. torque is not applicable. The torque required to engage and disengage shall not exceed 4 inchpounds (0.452 Nm). Longitudinal force is 4.5 lbs. (20 N). See interface dimensions shown on next page. Applicable to Females only: oversize pin.093 inch (2.36 mm) max. dia.,.125 inch (3.2 mm) deep; insertion force 2 lbs. (8.9 N) max. with.092 inch (2.34 mm) min. dia. pin; withdrawal force 2.00 oz (.556 N) min. with.090 inch (2.29 mm) max. dia. pin. Not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 750 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: cinter.pm5

64 Interface Mating Dimensions (Per MILC39012 (IEC1697)) C C Female 1cinter.pm5 C Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 65

65 BetweenSeries Adapters to Type C Part No CFem. to NFem. DC 10.0 GHz x f (GHz) Part No CMale to NFem. DC 10.0 GHz x f (GHz) Part No CFem. to NMale DC 10.0 GHz x f (GHz) Part No CMale to NMale DC 10.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1cbt.pm5

66 Adapters HN BetweenSeries Adapters HN If your choice of HN Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. HN N Page 70 "HN" In Series Adapters available on request. 1hnb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 67

67 HN Specifications to MILC3643 The specifications below are general specifications for all HN connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC3643, these specifications shall govern. The paragraph numbers refer to the associated requirement paragraphs of MILC3643. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque Moisture Resistance Corona Level 68 REQUIREMENT PARAGRAPH STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 8.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.0 milliohms and the outer contact resistance drop shall not exceed 0.2 milliohms. The magnitude of the test voltage shall be 5000 volts rms at sea level. The RF high potential withstanding voltage is 1,500 volts rms at 5 MHz. Leakage is not applicable. (95 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 150 pounds (667 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max. The torque is 30 inchpounds (3.4 Nm) max. The torque required to engage and disengage shall not exceed 6.2 inchpounds (0.7 Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.072 inch (1.8 mm) max. dia.,.187 inch (4.75 mm) deep; insertion force 2 lbs. (8.9 N) max. with.065 inch (1.65 mm) min. dia. pin; withdrawal force with max. dia. pin. is not applicable inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Corona Level is not applicable. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: hninter.pm5

68 Interface Mating Dimensions (Per MILC3643) HN HN Female 1hninter.pm5 HN Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 69

69 BetweenSeries Adapters to Type HN Part No HNFem. to NFemale DC 8.0 GHz x f (GHz) Part No HNFem. to NMale DC 8.0 GHz x f (GHz) Part No HNMale to NFemale DC 8.0 GHz x f (GHz) Part No HNMale to NMale DC 8.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1hnbt.pm5

70 Adapters K* InSeries and BetweenSeries Adapters K* If your choice of K* Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. K* 2.4 mm 3.5 mm 7 mm K* N SMP Please refer to 7 mm BetweenSeries Adapters Please refer to N BetweenSeries Adapters Pages Pages Page 41 Pages Pages Pages sk.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 71

71 K* Specifications The specifications below are general specifications for all K* connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 40.0 GHz min. Insulation resistance is not applicable * f (GHz) The center contact resistance drop shall not exceed 2.0 milliohms and the outer contact resistance drop shall not exceed 0.4 milliohms. The magnitude of the test voltage shall be 1,000 volts rms at sea level. RF high potential withstanding voltage not applicable. Leakage is not applicable. (100 f (GHz)) db (.5 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 60 pounds (267 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max. The torque is 15 inchpounds (1.7 Nm) max. The torque required to engage and disengage shall not exceed 2 inchpounds (0.226 Nm). Longitudinal force is not applicable. Mating Characteristics are not applicable inchpounds ( Nm) ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 72 Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Corona Level is not applicable. * 'K' Connector is a trademark of Wiltron Company. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: skinter.pm5

72 Interface Mating Dimensions K* K* Female 1skinter.pm5 K* Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) * 'K' Connector is a trademark of Wiltron Company. 73

73 InSeries Adapters to Type K* Part No. KFKF * * KFem. to KFem. DC 40.0 GHz 1.15 : 1 Part No. Part No. Part No. Part No. KFWI * * KFem. to KFem. DC 40.0 GHz 1.15 : 1 4Hole Flange 80KFKF * * KFem. to KFem. DC 40.0 GHz 1.15 : 1 Bulkhead Feedthrough 8003KFKF * * KFem. to KFem. DC 40.0 GHz 1.15 : 1 Radius Right Angle 8091KFKF * * KFem. to KFem. DC 40.0 GHz for direct connection with Wiltron : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company. 74 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: skb.pm5

74 InSeries Adapters to Type K* Part No. Radius Right Angle Part No. Radius Right Angle Part No. KFKM * * KMale to KFem. DC 40.0 GHz 1.15 : KFKM * * KMale to KFem. DC 40.0 GHz 1.30 : KMKM * * KMale to KMale DC 40.0 GHz 1.30 : 1 Part No. KMKM * * KMale to KMale DC 40.0 GHz 1.15 : 1 Part No. KMWI * * KMale to KFem. DC 40.0 GHz Date: skb.pm : 1 for direct connection with Wiltron 360 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 75

75 BetweenSeries Adapters to Type K* Part No. HFKF 2.4mmF to KFem. DC 40.0 GHz 1.15 : 1 * Part No. HFKM 2.4mmF to KMale DC 40.0 GHz 1.15 : 1 * Part No. H2KF 2.4mmF to KFem. DC 40.0 GHz 1.15 : 1 * for direct connection with HP 8510 Part No. H2KM * 2.4mmF to KMale DC 40.0 GHz 1.15 : 1 for direct connection with HP 8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company 76 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1skb.pm5

76 BetweenSeries Adapters to Type K* for direct connection with Wiltron 360 Part No. HFWI 2.4mmF to KFem. DC 40.0 GHz 1.15 : 1 * for direct connection with Wiltron 360 Part No. HMWI * 2.4mmM to KFem. DC 40.0 GHz 1.15 : 1 Part No. HMKF 2.4mmM to KFem. DC 40.0 GHz 1.15 : 1 * Part No. HMKM * 2.4mmM to KMale DC 40.0 GHz 1skb.pm : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 77

77 BetweenSeries Adapters to Type K* Part No. KF92 3.5mmF to KFem. DC 35.0 GHz 1.15 : 1 * Part No. KF91 3.5mmM to KFem. DC 35.0 GHz 1.15 : 1 * Part No. H3KF 3.5mmF to KFem. DC 35.0 GHz 1.15 : 1 * for direct connection with HP8510 Part No. WI92 * 3.5mmF to KFem. DC 35.0 GHz 1.15 : 1 for direct connection with Wiltron 360 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company 78 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1skb.pm5

78 BetweenSeries Adapters to Type K* Part No. KM92 3.5mmF to KMale DC 35.0 GHz 1.15 : 1 * for direct connection with HP 8510 Part No. H3KM 3.5mmF * to KMale DC 35.0 GHz 1.15 : 1 for direct connection with Wiltron 360 Part No. WI91 3.5mmM to KFem. DC 35.0 GHz 1.15 : 1 * Part No. KM91 * 3.5mmM to KMale DC 35.0 GHz 1skb.pm : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 79

79 BetweenSeries Adapters to Type K* Part No. Part No. Part No. Part No. KFMP * SMPFem. to KFem. DC 40.0 GHz 1.20 : 1 full detent KFMJ * SMPMale to KFem. DC 40.0 GHz 1.20 : 1 limited detent 80KFMJ * SMPMale to KFem. DC 40.0 GHz 1.20 : 1 smooth bore 8003KFMJ * SMPMale to KFem. DC 40.0 GHz 1.20 : 1 Part No. 8004KFMJ * SMPMale to KFem. DC 40.0 GHz 1.20 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company 80 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1skb.pm5

80 BetweenSeries Adapters to Type K* Part No. full detent Part No. limited detent Part No. smooth bore Part No. KMMP * SMPFem. to KMale DC 40.0 GHz 1.20 : 1 KMMJ * SMPMale to KMale DC 40.0 GHz 1.20 : 1 80KMMJ * SMPMale to KMale DC 40.0 GHz 1.20 : KMMJ * SMPMale to KMale DC 40.0 GHz 1.20 : 1 Part No. 8004KMMJ * SMPMale to KMale DC 40.0 GHz 1skb.pm : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 81

81 Adapters N 1n.pm5 InSeries and BetweenSeries Adapters N If your choice of N Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. N 1.4/4.4 Page mm Pages mm Pages mm Please refer to 7 mm BetweenSeries Adapters Page 42 7/16 The PUSH ON Page 51 7/16 Page 97 BMA Page 98 BNC Page 99 C Page 100 HN Page 101 K* Pages N The PUSH ON Page 87 N Pages SBX Page 104 SBY Page 105 SC Page 106 SMA The PUSH ON Page 87 SMA Pages TNC The PUSH ON Page 87 TNC Pages TNX Page 114 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 83

82 N Specifications to MILC39012 The specifications below are general specifications for all N connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC39012, these specifications shall govern. The paragraph numbers refer to the associated requirement paragraphs of MILC39012/C. These specifications are subject to change according to the latest revision. REQUIREMENT REQUIREMENT PARAGRAPH GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Connector Durability Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Centre Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 18.0 GHz min., optional DC 20.0 GHz The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.0 milliohms and the outer contact resistance drop shall not exceed 0.2 milliohms. The magnitude of the test voltage shall be 2,500 volts rms at sea level. The RF high potential withstanding voltage is 1,500 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 90 pounds (400 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 30 inchpounds (3.4 Nm) max. The torque required to engage and disengage shall not exceed 6 inchpounds (0.678 Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.067 inch (1.7 mm) max. dia.,.125 inch (3.2 mm) deep; insertion force 2 lbs. (8.9 N) max. with.066 inch (1.67 mm) min. dia. pin; withdrawal force 1.00 oz (.278 N) min. with.0645 inch (1.64 mm) max. dia. pin inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Moisture Resistance Corona Level Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 500 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 84 Date: ninter.pm5

83 Interface Mating Dimensions (Per MILC39012) N N Female N Male 1ninter.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 85

84 Lockable Push On Connector to Type N The PushOn 'Connector Saver' was developed to eliminate the time consuming lightening, torquing and loosening of N connectors during test. The standard N female end engages the N male of the cable assembly, while the PushOn end of the adapter slides directly onto any N female, allowing quick connecting and disconnecting. Its mechanism locks safely onto any standard Ntypethread (5/8"24 UNEF). Connector Saver PushOn Nm Safe Locking Mechanism Repeatable Performance Features Reduced Test Times Low Return Loss DC18.0 GHz Long Life 86 Specifications: Electrical: Impedance 50 Ohms nominal Range DC to 18.0 GHz Max. VSWR 1.15 : 1 Insertion Loss 0.2 db max. at 18 GHz Contact Resistance 1.0 milliohms max. RF Leackage 90 db max. to 3.0 GHz 75 db max. to 18.0 GHz Diel. Withstdg. Voltage 2500 VRMS, 60 Hz RF High Potential Mhz Corona Level Voltage ,000 ft. Mechanical: Temperature Rating 65 C to +100 C Durability 500 mating cycles min. Materials: Body Stainless Steel Center Contact Beryllium Copper Outer Conductor Beryllium Copper Finish: Center Contact Gold Plate per MILG45204, type II, class I, grade C. Body Passivate per QQP35 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nin.pm5

85 Push On Adapters of Type N Part No. NS61 NPush to NFem. DC 18.0 GHz Part No. 80 NS61 NPush to NFem. DC 18.0 GHz This Push On locks onto Bulkhead Feedthrough Jack N Part No NS61 NPush to NFem. DC 18.0 GHz Part No. NS21 NPush to SMAFem. DC 18.0 GHz Part No. NS41 NPush to TNCFem. DC 18.0 GHz 1nin.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 87

86 InSeries Adapters to Type N Part No NFem. to NFem. DC 18.0 GHz High Power Outer Conductor is stainless steel gold plated. Part No NFem. to NFem. DC 12.4 GHz 1.15 : 1 Part No. Radius Right Angle NFem. to NFem. DC 18.0 GHz 1.20 : 1 Part No NFem. to NFem. DC 18.0 GHz 1.20 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section NJack/ / N Bulkhead feedthrough Jack Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nin.pm5

87 InSeries Adapters to Type N 4Hole Flange Part No NFem. to NFem. DC 18.0 GHz Bulkhead Feedthrough Part No NFem. to NFem. DC 18.0 GHz Part No NMale to NFem. DC 18.0 GHz 1nin.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 89

88 InSeries Adapters to Type N Part No. High Power NMale to NFem. DC 18.0 GHz 1.15 : 1 Part No. Right Angle NMale to NFem. DC 18.0 GHz 1.15 : 1 Part No. Radius Right Angle NMale to NFem. DC 18.0 GHz 1.20 : 1 Outer Conductor is stainless steel gold plated, coupling nut is stainless steel passivated. Part No NMale to NFem. Right Angle, High Power DC 10.0 GHz 1.15 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 90 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nin.pm5

89 InSeries Adapters to Type N Part No NMale to NMale DC 18.0 GHz High Power Outer Conductor is stainless steel gold plated, coupling nuts are stainless steel passivated. Part No NMale to NMale DC 12.4 GHz 1.15 : 1 Radius Right Angle Part No NMale to NMale DC 18.0 GHz 1.20 : 1 1nin.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 91

90 BetweenSeries Adapters to Type N Part No /4.4 to NFem. DC 18.0 GHz x f (GHz) Part No /4.4 to NFem. DC 18.0 GHz x f (GHz) Part No /4.4 to NMale DC 18.0 GHz x f (GHz) Part No /4.4 to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

91 BetweenSeries Adapters to Type N Part No. HF61 2.4mmF to NFem. DC 18.0 GHz for direct connection with HP8510 Part No. H mmF to NFem. DC 18.0 GHz Part No. HF51 2.4mmF to NMale DC 18.0 GHz Part No. H mmF to NMale DC 18.0 GHz 1nb1.pm5 for direct connection with HP8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 93

92 BetweenSeries Adapters to Type N Part No. HM61 2.4mmM to NFem. DC 18.0 GHz Part No. HM51 2.4mmM to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 94 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

93 BetweenSeries Adapters to Type N Part No mmF to NFem. DC 18.0 GHz 4Hole Flange Part No mmF to NFem. DC 18.0 GHz for direct connection with HP8510 Part No. H mmF to NFem. DC 18.0 GHz Part No. H mmF to NMale DC 18.0 GHz 1nb1.pm5 for direct connection with HP8510 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 95

94 BetweenSeries Adapters to Type N Part No mmF. to NMale DC 18.0 GHz Part No mmMale to NFem. DC 18.0 GHz Part No. 4Hole Flange mmMale to NFem. DC 18.0 GHz Part No mmM to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 96 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

95 BetweenSeries Adapters to Type N Part No /16Fem. to NFem. DC 7.5 GHz Part No /16Fem. to NMale DC 7.5 GHz Part No /16Male to NFem. DC 7.5 GHz Part No /16Male to NMale DC 7.5 GHz 1nb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 97

96 BetweenSeries Adapters to Type N Part No. BW61 BMAFem. to NFem. DC 18.0 GHz Part No. BW51 BMAFem. to NMale DC 18.0 GHz Part No. BM61 BMAMale to NFem. DC 18.0 GHz Part No. BM51 BMAMale to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 98 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

97 BetweenSeries Adapters to Type N Part No BNCFem. to NFem. DC 4.0 GHz x f (GHz) Part No BNCMale to NFem. DC 4.0 GHz x f (GHz) Part No BNCFem. to NMale DC 4.0 GHz x f (GHz) Part No BNCMale to NMale DC 4.0 GHz 1nb1.pm x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 99

98 BetweenSeries Adapters to Type N Part No CFem. to NFem. DC 10.0 GHz x f (GHz) Part No CMale to NFem. DC 10.0 GHz x f (GHz) Part No CFem. to NMale DC 10.0 GHz x f (GHz) Part No CMale to NMale DC 10.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

99 BetweenSeries Adapters to Type N Part No HNFem. to NFemale DC 8.0 GHz x f (GHz) Part No HNFem. to NMale DC 8.0 GHz x f (GHz) Part No HNMale to NFemale DC 8.0 GHz x f (GHz) Part No HNMale to NMale DC 8.0 GHz 1nb1.pm x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 101

100 BetweenSeries Adapters to Type N Part No. KF61 * KFemale to NFem. DC 18.0 GHz Part No. KF51 * KFemale to NMale DC 18.0 GHz Part No. KM61 * KMale to NFem. DC 18.0 GHz Part No. KM51 * KMale to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company 1 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

101 BetweenSeries Adapters to Type N for direct connection with Wiltron 360 Part No. WI61 * KFemale to NFem. DC 18.0 GHz for direct connection with Wiltron 360 Part No. WI51 * KFemale to NMale DC 18.0 GHz 1nb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 103

102 BetweenSeries Adapters to Type N Part No. XF61 SBXFem. to NFem. DC 8.0 GHz x f (GHz) Part No. XF51 SBXFem. to NMale DC 8.0 GHz x f (GHz) Part No. XM61 SBXMale to NFem. DC 8.0 GHz x f (GHz) Part No. XM51 SBXMale to NMale DC 8.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

103 BetweenSeries Adapters to Type N Part No. YF61 SBYFem. to NFem. DC 12.0 GHz x f (GHz) Part No. YF51 SBYFem. to NMale DC 12.0 GHz x f (GHz) Part No. YM61 SBYMale to NFem. DC 12.0 GHz x f (GHz) Part No. YM51 SBYMale to NMale DC 12.0 GHz 1nb1.pm x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 105

104 BetweenSeries Adapters to Type N Part No SCFem. to NFemale DC 10.0 GHz x f (GHz) Part No SCFemale to NMale DC 10.0 GHz x f (GHz) Part No SCMale to NFemale DC 10.0 GHz x f (GHz) Part No SCMale to NMale DC 10.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: nb1.pm5

105 BetweenSeries Adapters to Type N Part No SMAFem. to NFem. DC 18.0 GHz 4Hole Flange Part No SMAFem. to NFem. DC 18.0 GHz Bulkhead Feedthrough Part No SMAFem. to NFem. DC 18.0 GHz 4Hole Flange Part No SMAFem. to NFem. DC 18.0 GHz 1nb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 107

106 BetweenSeries Adapters to Type N Part No SMAFem. to NFem. DC 18.0 GHz Part No. 4Hole Flange SMAFem. to NFem. DC 18.0 GHz Part No SMAFem. to NMale DC 18.0 GHz Part No SMAFem. to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 108 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

107 BetweenSeries Adapters to Type N 4Hole Flange Part No SMAFem. to NMale DC 18.0 GHz 4Hole Flange with Gasket at the Flange Part No SMAFem. to NMale DC 18.0 GHz Part No SMAMale to NFem. DC 18.0 GHz 4Hole Flange Part No SMAMale to NFem. DC 18.0 GHz 1nb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 109

108 BetweenSeries Adapters to Type N Part No. 4Hole Flange SMAMale to NFem. DC 18.0 GHz Part No SMAMale to NFem. DC 18.0 GHz Part No SMAMale to NMale DC 18.0 GHz Part No SMAMale to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 110 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

109 BetweenSeries Adapters to Type N Part No TNCFem. to NFem. DC 18.0 GHz High Power Outer Conductor is stainless steel gold plated. Part No TNCFem. to NFem. DC 12.4 GHz 1.15 : 1 Part No TNCFem. to NMale DC 18.0 GHz High Power Outer Conductor is stainless steel gold plated, coupling nut is stainless steel passivated. Part No TNCFem. to NMale DC 12.4 GHz 1nb1.pm : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 111

110 BetweenSeries Adapters to Type N Part No TNCMale to NFem. DC 18.0 GHz 1.15 : 1 High Power Part No TNCMale to NFem. DC 18.0 GHz 1.15 : 1 Outer Conductor is stainless steel gold plated, coupling nut is stainless steel passivated. Part No TNCMale to NFem. DC 18.0 GHz High Power 1.15 : 1 Outer Conductor is stainless steel gold plated, coupling nut is stainless steel passivated. Part No TNCMale to NFem. DC 12.4 GHz High Power 1.15 : 1 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 112 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: nb1.pm5

111 BetweenSeries Adapters to Type N TNCInterface as per MILC87104/2 Right Angle Part No TNCMale to NFem. DC 18.0 GHz 1.20 : 1 Part No TNCMale to NMale DC 18.0 GHz High Power Outer Conductor is stainless steel gold plated, coupling nut is stainless steel passivated. Part No TNCMale to NMale DC 12.4 GHz 1.15 : 1 1nb1.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 113

112 BetweenSeries Adapters to Type N Part No TNXFem. to NFem. DC 18.0 GHz Part No TNXF to NMale DC 18.0 GHz Part No TNXMale to NFem. DC 18.0 GHz Part No TNXMale to NMale DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 114 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1nb1.pm5

113 Adapters SBX InSeries and BetweenSeries Adapters SBX If your choice of SBX Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. SBX 7/16 N SMA Please refer to N BetweenSeries Adapters Please refer to SMA BetweenSeries Adapters Page 118 Page 104 Page 137 "SBX": Developed to connect High Power Modules in the range of DC to 8.0 GHz. 1sbx.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 115

114 SBX Specifications The specifications below are general specifications for all SBX connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 8.0 GHz min. The insulation resistance shall not be less than megohms * f (GHz) The center contact resistance drop shall not exceed 0,8 milliohms and the outer contact resistance drop shall not exceed 1.5 milliohms. The magnitude of the test voltage shall be 4,000 volts rms at sea level. The RF high potential withstanding voltage is 2,500 volts rms at 5 MHz. Leakage is not applicable. RF Leakage is not applicable (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 5000 insertions. Withdrawal cycles not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 116 Cable Retention Force is not applicable. Coupling Nut Retention Force is not applicable. Force to engage and disengage is not applicable. Longitudinal force is not applicable. Mating Characteristics are not applicable Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition 1. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 750 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: sbxint.pm5

115 Interface Mating Dimensions SBX SBX Female : DC 8.0 GHz min. SBX Male 1sbxint.pm5 : DC 8.0 GHz min. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 117

116 BetweenSeries Adapters to Type SBX Part No. XF76 7/16F to SBXF DC 7.5 GHz Part No. XM76 7/16F to SBXM DC 7.5 GHz Part No. XF75 7/16M to SBXF DC 7.5 GHz Part No. XM75 7/16M to SBXM DC 7.5 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 118 1sbxb.pm5

117 Adapters SBY BetweenSeries Adapters SBY If your choice of SBY Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. SBY 7/16 N SMA Please refer to N BetweenSeries Adapters Please refer to SMA BetweenSeries Adapters Page 122 Page 105 Page 138 "SBY": Developed to connect High Power Modules in the range of DC to 12.0 GHz. 1sby.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 119

118 SBY Specifications The specifications below are general specifications for all SBY connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 12.0 GHz min. The insulation resistance shall not be less than megohms * f (GHz) The center contact resistance drop shall not exceed 1.0 milliohms and the outer contact resistance drop shall not exceed 1.5 milliohms. The magnitude of the test voltage shall be volts rms at sea level. The RF high potential withstanding voltage is volts rms at 5 MHz. Leakage is not applicable. RF Leakage is not applicable (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 5000 insertions. Withdrawal cycles not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 120 Cable Retention Force is not applicable. Coupling Nut Retention Force is not applicable. Force to engage and disengage is not applicable. Longitudinal force is not applicable. Mating Characteristics are not applicable Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 2800 volts rms and the altitude is 0 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: sbyint.pm5

119 Interface Mating Dimensions SBY SBY Female : DC 12.0 GHz min. SBY Male 1sbyint.pm5 : DC 12.0 GHz min. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 121

120 BetweenSeries Adapters to Type SBY Part No. YF76 7/16F to SBYF DC 7.5 GHz Part No. YM76 7/16F to SBYM DC 7.5 GHz Part No. YF75 7/16M to SBYF DC 7.5 GHz Part No. YM75 7/16M to SBYM DC 7.5 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 122 1sbyb.pm5

121 Adapters SC BetweenSeries Adapters SC If your choice of SC Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. SC 7 mm Please refer to 7 mm BetweenSeries Adapters Page 40 N Page 106 1scb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 123

122 SC Specifications to MILC39012 The specifications below are general specifications for all SC connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC39012, these specifications shall govern. The paragraph numbers refer to the associated requirement paragraphs of MILC39012/C. These specifications are subject to change according to the latest revision. REQUIREMENT REQUIREMENT PARAGRAPH GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 10.0 GHz. min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.0 milliohms and the outer contact resistance drop shall not exceed 0.15 milliohms. The magnitude of the test voltage shall be 3000 volts rms at sea level. The RF high potential withstanding voltage is 2,500 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 90 pounds (400 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) min.. The torque is 30 inchpounds (3.4 Nm) max. The torque required to engage and disengage shall not exceed 6 inchpounds (0.678 Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.098 inch (2.49 mm) min. dia.,.125 inch (3.17 mm) min. deep; insertion force 2 lbs. (8.9 N) max. with.092 inch (2.34 mm) min. dia. pin; withdrawal force 2.00 oz (.556 N) min. with.090 inch (2.29 mm) max. dia. pin inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 750 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: scinter.pm5

123 Interface Mating Dimensions (Per MILC39012) SC SC Female 1scinter.pm5 SC Male Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 125

124 BetweenSeries Adapters to Type SC Part No SCFem. to NFemale DC 10.0 GHz x f (GHz) Part No SCFemale to NMale DC 10.0 GHz x f (GHz) Part No SCMale to NFemale DC 10.0 GHz x f (GHz) Part No SCMale to NMale DC 10.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1scbe.pm5 Date: 03.97

125 Adapters SMA InSeries and BetweenSeries Adapters SMA If your choice of SMA Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. SMA 7 mm Please refer to 7 mm BetweenSeries Adapters Page 43 BMA Page 135 BNC Page 136 N The PUSH ON Page 87 N Please refer to N BetweenSeries Adapters Pages SBX Page 137 SBY Page 138 SMA The PUSH ON Page 131 SMA Pages SPM Page 139 TNC The PUSH ON Page 157 TNC Page 140 TNX Page 141 1sma.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 127

126 SMA Specifications to MILC39012 The specifications below are general specifications for all SMA connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC39012, these specifications shall govern. The paragraph numbers refer to the associated requirement paragraphs of MILC39012/C. These specifications are subject to change according to the latest revision. REQUIREMENT REQUIREMENT GENERAL SPECIFICATIONS PARAGRAPH GENERAL Standard Materials Finish for Design ELECTRICAL COPPER BERYL LIUM MECHANICAL Connector Durability STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 18.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 3.0 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,000 volts rms at sea level. The RF high potential withstanding voltage is 760 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertions and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 60 pounds (267 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 15 inchpounds (1.7 Nm) max. The torque required to engage and disengage shall not exceed 2 inchpounds (0.226 Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.0376 inch (.955 mm) max. dia.,.045 inch (1.14 mm) deep; insertion force 3 lbs. (13.34 N) max. with.037 inch (.94 mm) min. dia. pin; withdrawal force 1.00 oz (.278 N) min. with.0355 inch (.90 mm) max. dia. pin inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition D. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Moisture Resistance Corona Level Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 375 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 128 Date: smaint.pm5

127 Interface Mating Dimensions (Per MILC39012) SMA SMA Female SMA Male 1smaint.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 129

128 Lockable Push On Connector to Type SMA The PushOn 'Connector Saver' was developed to eliminate the time consuming lightening, torquing and loosening of SMA connectors during test. The standard SMA female end engages the SMA male of the cable assembly, while the PushOn end of the adapter slides directly onto any SMA female, allowing quick connecting and disconnecting. Its mechanism locks safely onto any standard SMAtypethread (1/4"36 UNS). Connector Saver PushOn SMA Safe Locking Mechanism Repeatable Performance Features Reduced Test Times Low Return Loss DC26.5 GHz Long Life 130 Specifications: Electrical: Impedance 50 Ohms nominal Range DC to 26.5 GHz Max. VSWR 1.15 : 1 (DC 18.0 GHz) 1.20 :1 ( ,5 GHz) Insertion Loss 0.3 db max. at 18 GHz Contact Resistance 3.0 milliohms max. RF Leackage 80 db max. to 3.0 GHz 65 db max. to 26.5 GHz Diel. Withstdg. Voltage 1500 VRMS, 60 Hz RF High Potential Mhz Corona Level Voltage ,000 ft. Mechanical: Temperature Rating 65 C to +165 C Durability 500 mating cycles min. Materials: Body Stainless Steel Center Contact Beryllium Copper Outer Conductor Beryllium Copper Finish: Center Contact Gold Plate per MILG45204, type II, class I, grade C. Body Passivate per QQP35 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1smapu.pm5

129 Push On Adapters of Type SMA SMAPUSHON Part No. SM21 SMAPUSHON Part No. 8003SM21 SMAPUSHON Part No. 8005SM21 SMAPush to SMAF DC 26.5 GHz 1.20 : 1 SMAPush to SMAF DC 26.5 GHz 1.20 : 1 SMAPush to SMAF DC 26.5 GHz Easier Handling with the enlarged coupling nut. SMA Push On Two Hole Flange Mount Floating Rear Mount Connector Saver The lockable SMAPush On will be available early : 1 SMAPUSHON Part No. 8004SM21 SMAPUSHON Part No. 8006SM21 SMAPush to SMAF DC 26.5 GHz 1.20 : 1 SMAPush to SMAF DC 26.5 GHz 1.20 : 1 1smapu.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 131

130 InSeries Adapters to Type SMA Part No SMAF to SMAF DC 18.0 GHz Part No. Bulkhead Feedthrough SMAF to SMAF DC 18.0 GHz x f (GHz) Part No. 4Hole Flange SMAF to SMAF DC 18.0 GHz Part No. Right Angle SMAF to SMAF DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 132 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1smain.pm5

131 InSeries Adapters to Type SMA Radius Right Angle Part No SMAF to SMAF DC 25.0 GHz Part No SMAM to SMAF DC 18.0 GHz Part No SMAM to SMAF DC 18.0 GHz Bulkhead Feedthrough Part No SMAM to SMAF DC 18.0 GHz 1smain.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 133

132 InSeries Adapters to Type SMA Part No Right Angle SMAM to SMAF DC 18.0 GHz Part No. Radius Right Angle SMAM to SMAF DC 25.0 GHz Part No. Part No. Part No SMAM to SMAM DC 18.0 GHz Right Angle SMAM to SMAM DC 18.0 GHz Radius Right Angle SMAM to SMAM DC 25.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 134 1smain.pm5

133 BetweenSeries Adapters to Type SMA Part No. BW21 BMAF to SMAF DC 18.0 GHz Part No. BW11 BMAF to SMAM DC 18.0 GHz Part No. BM21 BMAM to SMAF DC 18.0 GHz Part No. BM11 BMAM to SMAM DC 18.0 GHz 1smab.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 135

134 BetweenSeries Adapters to Type SMA Part No BNCF to SMAF DC 4.0 GHz x f (GHz) Part No BNCF to SMAM DC 4.0 GHz x f (GHz) Part No BNCM to SMAF DC 4.0 GHz x f (GHz) Part No BNCM to SMAM DC 4.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section x f (GHz) Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1smab.pm5

135 BetweenSeries Adapters to Type SMA Part No. XF21 SBXF to SMAF DC 8.0 GHz Part No. XF11 SBXF to SMAM DC 8.0 GHz Part No. XM21 SBXM to SMAF DC 8.0 GHz Part No. XM11 SBXM to SMAM DC 8.0 GHz 1smab.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 137

136 BetweenSeries Adapters to Type SMA Part No. YF21 SBYF to SMAF DC 12.0 GHz Part No. YF11 SBYF to SMAM DC 12.0 GHz Part No. YM21 SBYM to SMAF DC 12.0 GHz Part No. YM11 SBYM to SMAM DC 12.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 138 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1smab.pm5

137 BetweenSeries Adapters to Type SMA Part No. PJ21 SPMF to SMAF DC 18.0 GHz Part No. PJ11 SPMF to SMAM DC 18.0 GHz Part No. PM21 SPMM to SMAF DC 18.0 GHz Part No. PM11 SPMM to SMAM DC 18.0 GHz 1smab.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 139

138 BetweenSeries Adapters to Type SMA Part No TNCF to SMAF DC 18.0 GHz Part No TNCF to SMAM DC 18.0 GHz Part No TNCM to SMAF DC 18.0 GHz Part No TNCM to SMAM DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 140 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1smab.pm5

139 BetweenSeries Adapters to Type SMA Part No TNXF to SMAF DC 18.0 GHz Part No TNXF to SMAM DC 18.0 GHz Part No TNXM to SMAF DC 18.0 GHz Part No TNXM to SMAM DC 18.0 GHz 1smab.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 141

140 Adapters SMP InSeries and BetweenSeries Adapters SMP If your choice of SMP Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. SMP 7 mm K* SMP Please refer to 7 mm BetweenSeries Adapters Please refer to K* BetweenSeries Adapters Page 44 Pages Page 146 1smpb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. * 'K' Connector is a trademark of Wiltron Company. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 143

141 SMP Specifications The specifications below are general specifications for all SMP connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications DESC and DESC 94008, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 40.0 GHz min. The insulation resistance shall not be less than megaohms. 1.5 : 1 max. to 40.0 GHz. The center contact resistance drop is 6.0 milliohms max. The magnitude of the test voltage shall be 500 volts rms at sea level. The RF high potential withstanding voltage is 325 volts rms at 5 MHz. Leakage is not applicable. RF Leakage is not applicable. (.10 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 100 insertions min.. Withdrawal cycles /minute are not applicable. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 20 pounds (88.9 N) min. Not applicable. The torque required to engage shall not exceed 15 lbs. (66.7 N). The disengage torque shall not exceed 2 lbs. (8.9 N) min. (full detent). Not applicable. Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Recommended Mating Torque is not applicable. Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition D. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, rating 65 C to +165 C. Moisture Resistance Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Corona Level The connector shall not exhibit breakdown (corona) when the applied voltage is 190 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 144 Date: smpint.pm5

142 Interface Mating Dimensions (Per DESC and DESC 94008) SMP SMP Female SMP Male full detent SMP Male limited detent SMP Male smooth bore SMP Male 1smpint.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 145

143 InSeries Adapters to Type SMP Part No. MPMP04 SMPF to SMPF DC 40.0 GHz 1.5 : 1 to 40 GHz SMP Between Series Adapters 7 mm K* Please refer to 7 mm BetweenSeries Adapters Please refer to K* BetweenSeries Adapters Page 44 Pages Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. * 'K' Connector is a trademark of Wiltron Company. 146 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1smpin.pm5

144 Adapters SPM BetweenSeries Adapters SPM If your choice of SPM Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. SPM SMA Page 150 "SPM": A small connector developed for High Power Applications in the range of DC to 18.0 GHz. 1spmb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 147

145 SPM Specifications The specifications below are general specifications for all SPM connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Centre Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 18.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 3.0 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,000 volts rms at sea level. The RF high potential withstanding voltage is 760 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertions and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 60 pounds (267 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 15 inchpounds (1.7 Nm) max. The torque required to engage and disengage shall not exceed 2 inchpounds (0.226 Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.0376 inch (.955 mm) max. dia.,.045 inch (1.14 mm) deep; insertion force 3 lbs. (13.34 N) max. with.037 inch (.94 mm) min. dia. pin; withdrawal force 1.00 oz (.278 N) min. with.0355 inch (.90 mm) max. dia. pin inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition D. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, rating 65 C to +165 C. Moisture Resistance Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Corona Level The connector shall not exhibit breakdown (corona) when the applied voltage is 350 volts rms and the altitude is 70,000 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 148 Date: spmint.pm5

146 Interface Mating Dimensions SPM SPM Female SPM Male 1spmint.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 149

147 BetweenSeries Adapters to Type SPM Part No. PJ21 SPMF to SMAF DC 18.0 GHz Part No. PJ11 SPMF to SMAM DC 18.0 GHz Part No. PM21 SPMM to SMAF DC 18.0 GHz Part No. PM11 SPMM to SMAM DC 18.0 GHz 21.4 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 150 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1spmbe.pm5

148 Adapters TNC InSeries and BetweenSeries Adapters TNC If your choice of TNC Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. TNC 7 mm Please refer to 7 mm BetweenSeries Adapters Page 45 BNC Page 161 N The PUSH ON Page 157 N Please refer to N BetweenSeries Adapters Pages SMA The PUSH ON Page 157 SMA Please refer to SMA BetweenSeries Adapters Page 140 TNC The PUSH ON Page 157 TNC Pages tnc.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 151

149 TNC Specifications to MILC39012 The specifications below are general specifications for all TNC connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC39012, these specifications shall govern. The paragraph numbers refer to the associated requirement paragraphs of MILC39012/C. These specifications are subject to change according to the latest revision. REQUIREMENT REQUIREMENT PARAGRAPH GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage High Potential Test Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level * * 3.17* * 3.24* 3.25* 3.5.1* 3.7* 3.13* 3.18* 3.19* 3.20* 3.21* GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 11.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.5 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,500 volts rms at sea level. The high potential test voltage is 1,500 volts rms. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 90 pounds (400 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 30 inchpounds (3.4 Nm) max. The torque required to engage and disengage shall not exceed 24 inchpounds ( Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.055 inch (1.4 mm) max. dia.,.080 inch (2.03 mm) deep; insertion force 2 lbs. (8.9 N) max. with.054 inch (1.37 mm) min. dia. pin; withdrawal force 2.00 oz (.556 N) min. with.052 inch (1.32 mm) max. dia. pin inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 375 volts rms and the altitude is 0 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: tncint.pm5

150 Interface Mating Dimensions (Per MILC39012) TNC TNC Female TNC Male 1tncint.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 153

151 TNC Specifications to MILC87104/2 The specifications below are general specifications for all TNC connectors. Specific Data for VSWR, Insertion Loss, R.F. leakage, etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and General Specifications MILC87104/2, these specifications shall govern. The paragraph numbers refer to the associated requirement paragraphs of MILC87104/2. These specifications are subject to change according to the latest revision. REQUIREMENT REQUIREMENT PARAGRAPH GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage High Potential Test Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level * * 3.17* * 3.24* 3.25* 3.5.1* 3.7* 3.13* 3.18* 3.19* 3.20* 3.21* GENERAL SPECIFICATIONS STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 m) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 m) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 m) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 18.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 1.5 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,500 volts rms at sea level. The high potential test voltage is 2,000 volts rms. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 90 pounds (400 N) min. Not applicable for Female connectors. For male connectors, the axial force is 100 lbs (445 N) max.. The torque is 30 inchpounds (3.4 Nm) max. The torque required to engage and disengage shall not exceed 24 inchpounds ( Nm). Longitudinal force is not applicable. See interface dimensions shown on next page. Applicable to Females only: oversize pin.055 inch (1.4 mm) max. dia.,.080 inch (2.03 mm) deep; insertion force 2 lbs. (8.9 N) max. with.054 inch (1.37 mm) min. dia. pin; withdrawal force 2.00 oz (.556 N) min. with.052 inch (1.32 mm) max. dia. pin inchpounds ( Nm) Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. The connector shall not exhibit breakdown (corona) when the applied voltage is 375 volts rms and the altitude is 0 feet. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) * not specified in MILC87104/2. It is refered here to MILC Date: tncint1.pm5

152 Interface Mating Dimensions (Per MILC87104/2) TNC TNC Female TNC Male 1tncint1.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 155

153 Lockable Push On Connector to Type TNC The PushOn 'Connector Saver' was developed to eliminate the time consuming lightening, torquing and loosening of TNC connectors during test. The standard TNC female end engages the TNC male of the cable assembly, while the PushOn end of the adapter slides directly onto any TNC female, allowing quick connecting and disconnecting. Its mechanism locks safely onto any standard TNCtypethread (7/16"28 UNEF). Connector Saver PushOn TNC Safe Locking Mechanism Repeatable Performance Features Reduced Test Times Low Return Loss DC18.0 GHz Long Life 156 Specifications: Electrical: Impedance 50 Ohms nominal Range DC to 18.0 GHz Max. VSWR 1.15 : 1 Insertion Loss 0.2 db max. at 18 GHz Contact Resistance 1.0 milliohms max. RF Leackage 90 db max. to 3.0 GHz 65 db max. to 18.0 GHz Diel. Withstdg. Voltage 2500 VRMS, 60 Hz RF High Potential Mhz Corona Level Voltage ,000 ft. Mechanical: Temperature Rating 65 C to +100 C Durability 500 mating cycles min. Materials: Body Stainless Steel Center Contact Beryllium Copper Outer Conductor Beryllium Copper Finish: Center Contact Gold Plate per MILG45204, type II, class I, grade C. Body Passivate per QQP35 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1tncpu.pm5

154 Push On Adapters of Type TNC TNCPUSHON Part No. TS41 TNCPush to TNCF DC 18.0 GHz TNCPUSHON Part No. TS61 TNCPush to NF DC 18.0 GHz TNCPUSHON Part No. TS21 TNCPush to SMAF DC 18.0 GHz 1tncpu.pm5 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 157

155 InSeries Adapters to Type TNC Part No TNCF to TNCF DC 18.0 GHz TNCInterfaces as per MILC87104/2 Part No TNCF to TNCF DC 18.0 GHz TNCInterfaces as per MILC87104/2 Part No. 4Hole Flange TNCF to TNCF DC 18.0 GHz TNCInterfaces as per MILC87104/2 Part No. Bulkhead Feedthrough TNCF to TNCF DC 18.0 GHz TNCInterfaces as per MILC87104/2 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 158 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1tncin.pm5

156 InSeries Adapters to Type TNC TNCInterfaces as per MILC87104/2 Radius Right Angle Part No TNCF to TNCF DC 18.0 GHz TNCInterfaces as per MILC87104/2 Part No TNCM to TNCF DC 18.0 GHz TNCInterfaces as per MILC87104/2 Part No TNCM to TNCF DC 18.0 GHz Radius Right Angle Part No TNCM to TNCF DC 18.0 GHz 1tncin.pm5 TNCInterfaces as per MILC87104/2 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 159

157 InSeries Adapters to Type TNC High Power Right Angle Outer Conductor is stainless steel gold plated, coupling nuts are stainless steel passivated. Part No TNCM to TNCF DC 10.0 GHz 1.20 : 1 Part No TNCM to TNCM DC 18.0 GHz TNCInterfaces as per MILC87104/2 High Power Outer Conductor is stainless steel gold plated, coupling nuts are stainless steel passivated. Part No TNCM to TNCM DC 12.4 GHz 1.15 : 1 Part No. Radius Right Angle TNCM to TNCM DC 18.0 GHz TNCInterfaces as per MILC87104/2 Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. 160 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 1tncin.pm5

158 BetweenSeries Adapters to Type TNC Part No BNCF to TNCF DC 4.0 GHz x f (GHz) Part No BNCF to TNCM DC 4.0 GHz x f (GHz) Part No BNCM to TNCF DC 4.0 GHz x f (GHz) Part No BNCM to TNCM DC 4.0 GHz 1tncb.pm x f (GHz) Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 161

159 Adapters TNX InSeries and BetweenSeries Adapters TNX If your choice of TNX Adapter is not shown in this section, please refer to the Table below to determine other possible locations. Should you not find your adapter listed in any section, please consult the factory or your Spectrum Area Representative. TNX 3.5mm Please refer to 3.5 mm BetweenSeries Adapters Page 32 7 mm Please refer to 7 mm BetweenSeries Adapters Page 46 N Please refer to N BetweenSeries Adapters Page 114 SMA Please refer to SMA BetweenSeries Adapters Page 141 TNX Page 166 1tnxb.pm5 Although our catalog incorporates a comprehensive range of products, due to our program of continuous development, it will not contain every product we manufacture. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 163

160 TNX Specifications The specifications below are general specifications for all TNX connectors. Specific Data for VSWR, Insertion loss, R.F. leakage etc., are available from the factory upon request. Specifications in the following table are recommended for any procurement documents or drawings. In the event of any conflict between these specifications and other documentation, these specifications shall govern. These specifications are subject to change according to the latest revision. REQUIREMENT GENERAL SPECIFICATIONS GENERAL Standard Materials Finish for Design ELECTRICAL MECHANICAL Connector Durability COPPER BERYLLIUM STAINLESS STEEL ALUMINUM BRASS VARIOUS Range Insulation Resistance Voltage Standing Wave Ratio (VSWR) Contact Resistance Dielectric Withstanding Voltage RF High Potential Withstanding Voltage RF Leakage Insertion Loss Cable Retention Force Coupling Nut Retention Force Force to Engage and Disengage Longitudinal Force max. Mating Characteristics Recommended Mating Torque STEEL corrosion resistant per DIN (QQS764, class 303 or ASTMA58280). ALUMINUM AlMg4.5Mn per DIN 1725, AlMgSi0.5 per DIN 1725, AlMgSi1 per DIN 1725 (6061T6 per QQA225/8). BRASS CuZn39Pb3 per DIN (QQB626, half hard). COPPER BERYLLIUM 3325 CuBe2Pb H per DIN (QQC530). TFE Fluorocarbon per DIN (MILP19468 and LP403). SILICONE RUBBER per DIN 3771 (MILR5847 and ZZR765, Class II B,) Grade BORRIUM NITRITE Dielectric for high power applications per inhouse specification. Center Contacts shall be gold plated to a minimum thickness of inch (1.27 µm) in accordance with MILG45204, Type II, Grade C. shall be passivated per QQP35. Conductive Parts shall have an iridited finish per MILC5541. Other parts, such as Coupling Nuts and BackBodies shall be anodized per MILA inch (0.8 µm) min.gold plating per MILG45204, or nicle plating per QQN290, as specified. Imoloy.0001 inch (2.5 µm) min. plating, consisting of 55% Copper / 20% Zinc / 25% Tin (on special request). The design shall be such that the outline dimensions in this catalog are met. In addition, the assembled connector shall meet the interface dimensions. DC 18.0 GHz min. The insulation resistance shall not be less than 5,000 megohms * f (GHz) The center contact resistance drop shall not exceed 2.0 milliohms and the outer contact resistance drop shall not exceed 2.0 milliohms. The magnitude of the test voltage shall be 1,500 volts rms at sea level. The RF high potential withstanding voltage is 1,000 volts rms at 5 MHz. Leakage is not applicable. (90 f (GHz)) db (.05 SQT(f(GHz))) db The connector is to be tested and its mating connector shall be subjected to 500 insertion and withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of mechanical failure and the connector shall meet the mating characteristic requirements. 60 pounds (267 N) min. Not applicable for Female connectors. For male connectors, the torque is 50 inchpounds (5.65 Nm) max.. The axial force is not applicable. The torque required to engage and disengage shall not exceed 2 inchpounds (0.226 Nm). Longitudinal force is not applicable. Mating Characteristics are not applicable inchpounds ( Nm) ENVIRONMENTAL Corrosion (Salt Spray) Vibration Shock Thermal Shock Moisture Resistance Corona Level 164 Specification MILSTD2, Method 101, Test Condition B. The salt solution shall be 5%. Specification MILSTD2, Method 204, Test Condition B. Specification MILSTD2, Method 213, Test Condition I. Specification MILSTD2, Method 107, Test Condition B, except high temperature shall be C. Specification MILSTD2, Method 106. Step 7b (vibration) shall be omitted. Insulation resistance shall be 200 megohms min. within 5 minutes of removal from humidity. Corona Level is not applicable. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) Date: tnxint.pm5

161 Interface Mating Dimensions TNX TNX Female TNX Male 1tnxint.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 165

162 InSeries Adapters to Type TNX Part No TNXF to TNXF DC 18.0 GHz Part No TNXM to TNXF DC 18.0 GHz Part No TNXM to TNXM DC 18.0 GHz Dimensions shown are inches over millimeters. Standard units have stainless steel finish (last two digits of the P/N are ). Interfaces are per MILC 39012, MILC87104/2, MILC3643, MILSTD348, IEC1697, IEC4572, DIN , DIN , DIN , where applicable. For details please refer to the beginning of this section. Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 166 1tnxin.pm5

163 Adapter Sets Customers may specify Adapters for their own custom compiled sets. Adapters can be ordered optimized for specific frequency bands as well. 1sets.pm5 Spectrum Elektrotechnik GmbH P.O. Box , Munich, Germany Tel. (89) , Fax (89) (Country Code: 49) 167