Parts Catalog Issued: May 1, Power Tiger. Wheelchair

Transcription

1 Parts Catalog Issued: May 1, 014 Power Tiger Wheelchair

2 Parts Catalog Usage Guide The information contained in this document is subject to change without notice. This catalog contains service parts for. If you have any questions regarding this catalog, please contact one of our Customer Service Representatives. SYMBOL DEFINITION For Customer Service Support Call: For Faxed In Orders Call: or For Technical Service Call: Literature Can Be Found at: or Throughout this catalog you will notice letters to draw your attention to specific footnotes which are located at the bottom of the page or below specified charts. Examples: A,B,C etc. NOTE: NLA = Special Comments = General information pertaining to that specific page = No Longer Available HARDWARE MEASUREMENTS The measurements for the hardware will be listed as follows: Screws, Bolts Diameter X Thread Count/Pitch X Length Washers Inside Diameter X Outside Diameter X Thickness Spacers Inside Diameter X Outside Diameter X Length For your convenience, we have supplied an area for you to list your Invacare Representatives. Name Phone Numbers 014 Invacare Corporation. Elyria, Ohio. Invacare, Yes, you can., the Blue Medallion Design are registered trademarks of Invacare Corporation. and Tiger and MKIV are trademarks of Invacare Corporation. Otto Bock is a registered trademark of Otto Bock Orthopaedische Industrie GMBH & Co.. Tash is a registered trademark of Tash International Inc.. Therafin is a registered trademark of W/R/ Medical Electronics Co.. Bussman is a registered trademark of Cooper Industries. MIDI is a registered trademark of Littelfuse Inc.. Dynamic is a registered trademark of Dynamic Controls Limited. 1

3 TABLE of CONTENTS Description Page Number A: READ THIS FIRST (THIS CATALOG IS DIFFERENT!)... 5 Accessories - Miscellaneous Accessories - Power Wheelchair Tool Kit Arms - Adjustable Height Backs - Solid - Mounting Hardware... 4 Backs - Solid & Solid Seats... 3 Battery Boxes & Tray Assembly - MK6i Electronics... 7 Battery Boxes & Tray Assembly - MKIV Electronics Canes - Back & Stroller Handle Assembly Casters & Forks (6") (8") Cylinders - Lock w/ Stop Assembly... Electronics - MK6i ~PLEASE READ THIS Electronics - MK6i IR Wireless Mouse Module Electronics - MK6i RF Wireless Mouse Module Electronics - MKIV Controller - Programmer & Attaching Hardware Electronics - MKIV Displays Electronics - MKIV Joystick Mounting Hardware & Joystick Accessories Electronics - MKIV Joystick Options Electronics - MKIV Joysticks - PS - PSF & PSR Electronics - MKIV Joysticks - RII - RX - A - A+ - TCHJOY Electronics - MKIV Mid-Line Swing Bracket Assembly... 88

4 TABLE of CONTENTS Description Page Number Electronics - MKIV R.I.M. Head Control Assembly (After 8/15/95) Electronics - MKIV R.I.M. Head Control Assembly (Before 8/16/95) Electronics - MKIV R.I.M. Head Control Mounting Hardware Electronics - MKIV Sip-N-Puff/Digital Interface & COM1 - COM Electronics - MKIV Swivel Joystick Hardware Electronics - Quad Link - QLA (After 10/30/05) Electronics - Quad Link Assembly (Before 10/31/05) Electronics - Tash & Therafin Accessories Frame Finishes - Touch-Up Paints & Upholstery Options... 6 Frames - Seat... 1 Frames - Seat & Back Cane Hardware Frames - Side & Hardware Frames - Width Growth Kits Front Riggings - AT5043 Flip-Up Footplates Front Riggings - Calf Pads & Ratchet Assemblies Front Riggings - Footrest & Legrest Accessories Front Riggings - Footrest Supports... 4 Front Riggings - Legrest Supports - ATL4A Front Riggings - One Piece Adjustable Angle Footboard Front Riggings - Pivot/Slide Tube & AT5543 Adjustable Angle Footplates (After /8/95) Front Riggings - Pivot/Slide Tube & AT5543 Adjustable Angle Footplates (Before 3/1/95)

5 TABLE of CONTENTS Description Page Number Front Riggings - Pivot/Slide Tube and Composite Footplates... 5 Motor & Gearbox Assembly Orbit Seat Option... 0 Orbit Seat Option - "T" Arm and Hardware Orbit Seat Option - Accessories - Stroller Handles Orbit Seat Option - Foot Pedal Release Assembly... 7 Orbit Seat Option - Seat Frame Assembly & Back Canes... 9 Orbit Seat Option - Seat Pans... 3 Orbit Seat Option - Seat Rail - Lower Seat Plate Assembly... 5 Packaging - Literature & Decals Tilt & Non-Tilt Hardware Warranty Replacement Parts Wheel Locks & Hardware Wheels - Rear & Motor Mounting Hardware Wiring Harnesses & Chargers - MK6i Electronics Wiring Harnesses & Chargers - MKIV Electronics

6 A: READ THIS FIRST (THIS CATALOG IS DIFFERENT!) 5

7 Frame Finishes, Touch-Up Paints and Upholstery Options Frame Finishes and Touch-Up Paint Color Number Part Number Bottle Size Color 0P NLA.6 oz Pink Pearl 06P NLA.6 oz Super Teal 08P NLA.6 oz Deep Purple 17P NLA.6 oz Cobalt Blue P NLA.6 oz Anthracite 4P NLA.6 oz Wet Black 9P NLA.6 oz White/ White Snow 30P NLA.6 oz Sunny Yellow 31P NLA.6 oz Lollipop Pink 33P NLA.6 oz Red 34P NLA.6 oz Flat Black 60P Silver Metallic 61P See Note(s) A NLA.6 oz Electric Red 6P See Note(s) A NLA.6 oz Electric Blue 64P See Note(s) A NLA.6 oz Metallic Blue 65P See Note(s) A NLA.6 oz. Metallic Green 69P NLA.6 oz Teflon Black 71P Silver Vein 80P NLA.6 oz Evergreen with Navy 81P NLA.6 oz Dark Olive with Copper 8P NLA.6 oz Fruit Punch with Fucshia 83P NLA.6 oz Royal Blue with Grape 84P NLA.6 oz Lavender 101P NLA.6 oz Jeweled Green 10P NLA.6 oz Denim Blue 103P NLA.6 oz Mocha Frost 104P NLA.6 oz Electric Teal 105P NLA.6 oz Midnight Blue 115P Black Prism 116P NLA.6 oz Sunkissed Orange 117P NLA.6 oz Tangerine Red 118P Fruit Fusion 119P Bubblegum Pink 10P Grape Madness 11P Lolly Pop Blue 1P Cosmic Blue 13P Celestial Purple 14P Vivid Violet 15P Emerald Green 6

8 Frame Finishes, Touch-Up Paints and Upholstery Options Frame Finishes and Touch-Up Paint Color Number Part Number Bottle Size Color NOTE: 16P 17P A - Veiling is not available on these colors. Shamrock Green Grasshopper Green 7

9 Frame Finishes, Touch-Up Paints and Upholstery Options Veil Options Color Number 13V 67V 19V 15V Color Dark Purple Veil Gold Veil Green Veil Grey Veil Sparkle Frame Finishes Color Number 7P 73P 74P 75P 76P 88P Color Twilight Sparkle Gold Sparkle Green Sparkle Blue Sparkle Red Sparkle Wet Black with Twilight Sparkle 8

10 Frame Finishes, Touch-Up Paints and Upholstery Options Upholstery Options Vinyl Colors U67 Black U75 Dove Grey U85 Dark Blue U86 Ruby U97 Sky Blue U88 Camel Nylon Colors U40 Black 9

11 Packaging, Literature and Decals 10

12 Packaging, Literature and Decals Item Number Note Part Number Description Quantity Per Package Assembly Carton, Cover NLA NLA - Tube, Paper Carton, Corner Reinforcement E See Note See Footnote Carton, Tray Bag, Poly (7" L x 35" W x 19" D) X011 Carton, Front Riggings X161 Insert, Plain Pad Decal, Transportation C Decal, Invacare Logo (1.6) NLA NLA - Plate, Name, Patent Numbers B,C NLA NLA - Decal, Model, Black - Power Tiger 1 1 C NLA NLA - Decal, Model, White - Power Tiger 1 A,D NLA NLA - Package, Decal, Black - Power Tiger 1 1 A,D NLA NLA - Package, Decal, White - Power Tiger 1 1 D Owner's Manual 1 1 NOTE: A - Decal Package includes Invacare logo, model, transportation and patent number decals. B - Used for chairs with frame colors 0P, 9P, 30P and 84P only. C - Invacare logo added and model decals changed 1/11/000. When replacing side frames before 1/11/000 order decals in pairs to match. D - Not Shown. E - Wood Skid is not supplied. Note: When adjusting or replacing parts, please refer to your owner's manual for assistance. 11

13 Seat Frame Assembly 1

14 Item Number Note Part Number Description Seat Frame Assembly Quantity Per Package Assembly 1 A,B Tube, Seat Rail, Color 1 1 A,C Tube, Seat Rail, Color Package, Locknut (1/4-0) 5 3 B Tube, Spacer 1 3 C Tube, Spacer, Black 1 4 B Tube, Slide, Seat Frame, Black 1 4 C Tube, Slide, Seat Frame, Black Screw, Socket Button Head (1/4-0 x 1-1/4") NL NLA - Tube, Fixed Front Frame 1 A Plug Button, Black (7/8") Screw, Hex Head w/ Patch (1/4-0 x ") Washer (1/4 x 1/ x 1/16") NL NLA - Footrest Mounting Tube w/ Sector Block, 1 1 A Color - Right NL NLA - Footrest Mounting Tube w/ Sector Block, 1 1 A Color - Left Kit, Sector Block - Right Kit, Sector Block - Left 1 1 NOTE: A - Specify frame color when ordering. B " Wide Chairs C " Wide Chairs 13

15 Back Canes and Stroller Handle Assembly 14

16 Back Canes and Stroller Handle Assembly Item Number Note Part Number Description Quantity Per Package Assembly 1 A NLA NLA - Tube, Cane Slide, Black B,F NLA NLA - Tube, Cane Slide, Black X009 Button, Single Snap Grip, Push Handle NLA NLA - Cane, Back, Black - Right NLA NLA - Cane, Back, Black - Left Plug Button, Black (7/8") Package, Locknut (1/4-0) NLA NLA - Bracket, Back Mounting, Black Screw, Socket Button Head (1/4-0 x 1-1/4") NLA NLA - Nut, Hex with Nylon Cap (#10-3) Washer, Nylon (3/16 x 7/16 x 1/8") NLA NLA - Bracket, Latch, Black - Right NLA NLA - Bracket, Latch, Black - Left NLA NLA - Screw, Flat Head (#10-3 x 1-1/") NLA NLA - Washer, Wave (3/16 x 7/16 x 1/16") Spacer (1/4 x 1/ x 1/") NLA NLA - Latch NLA NLA - Spring, Torsion - Right NLA NLA - Spring, Torsion - Left NLA NLA - Back Cane Assembly - Right NLA NLA - Back Cane Assembly - Left NLA NLA - Cap, End, Protective, Black X001-NLA NLA - Ring, Retaining NLA NLA - Grip, Foam, Bottom A Rod, Release B 1099-NLA NLA - Rod, Release Grip, Push Handle C NLA NLA - Tube, Spacer, Black (1") D NLA NLA - Tube, Spacer, Black (") E Tube, Spacer, Black (4") NLA NLA - Screw, Phillips Pan Head (#8-3 x 5/8") Pin, Quick Release with Lanyard Handle, Stroller, Black - Right Handle, Stroller, Black - Left C NLA NLA - Stroller Handle Assembly, Black (1-13" W) D Stroller Handle Assembly, Black (14" W) E Stroller Handle Assembly, Black (15-16" W) 1 1 NOTE: A " Wide Chairs B " Wide Chairs C - 1"-13" Wide Chairs D - 14" Wide Chairs. No longer available as a service part, must order Frame Width Growth Kit (104014) as its replacement. E - 15"-16" Wide Chairs F - No longer available as a service part, must order Frame Width Growth Kit (104014) as its replacement. 15

17 Seat Frame and Back Cane Hardware 16

18 Seat Frame and Back Cane Hardware Item Number Note Part Number Description Quantity Per Package Assembly Package, Locknut (1/4-0) NLA NLA - Washer, Flat (9/3 x 1 x 5/64) X019 Spacer, Coved (1/4 x 7/8 x 7/16") Plug Button, Black (7/8") Plate, Back Mounting, Right NLA NLA - Plate, Back Mounting, Left Package, Button Head Cap Screw (1/4-0 x 1-3/4") A NLA NLA - Spacer (9/3 x 7/8 x 1/") A Spacer (1/4 x 1/ x 1/") NLA NLA - Spacer (1/4 x 3/4 x 1-7/16") 1 10 B Locknut (1/4-0) 5 10 C NLA NLA - Locknut (#10-4) Screw, Socket Button Head (1/4-0 x 1-1/4") B NLA NLA - Screw, Socket Head (1/4-0 x 3-1/4") 1 1 C NLA NLA - Screw, Shoulder Hex Socket Head (1/4 x 1 1-3/4", #10-4) NLA NLA - Screw, Shoulder Hex Socket Head (5/16" x 1 1-1/4", 1/4-0) NOTE: A - 14" Wide B - 1 to 14" Wide C - 15 to 16" Wide 17

19 Tilt and Non-Tilt Hardware 18

20 Item Number Note Part Number Description Tilt and Non-Tilt Hardware Quantity Per Package Assembly Bolt, Shoulder (1/4 x 3/4") NLA NLA - Locknut (#10-4) NLA NLA - Screw, Shoulder Hex Socket Head (5/16" x 1 1-1/4", 1/4-0) Locknut (1/4-0) Link Washer, Nylon (3/8 x 7/8 x 1/16") E NLA NLA - Lever, Tilt, Black - Right E NLA NLA - Lever, Tilt, Black - Left Cable Package, Tie Wrap (5-5/8" L) Screw, Socket Button Head (1/4-0 x 1-1/4") Package, Locknut (1/4-0) Screw, Socket Button Head (1/4-0 x 1") A NLA NLA - Bracket, Actuator Switch Mounting, Black 1 1 B NLA NLA - Screw, Phillips Pan Head (#4-40 x 3/8") 1 B NLA NLA - Washer, Plain (1/8 x 5/16 x 1/3") 1 B P0870X000 Nut, Hex Keps (#4-40) Package, Locknut (1/4-0) NLA NLA - Screw, Hex Head (5/16-18 x 1-1/") X00 Locknut (5/16-18) Screw, Socket Button Head (1/4-0 x 1-1/4") NLA NLA - Washer, Plain (1/8 x 5/16 x 1/3") Washer, Nylon (1/4 x 1/ x 1/16") NLA NLA - Washer, Internal Tooth Lock (#4-40) NLA - Locknut (#4-40) Package, Locknut (1/4-0) Locknut, High Profile (#10-3) X003 Spacer (5/16 x 1/ x 3/8") NLA NLA - Plate, Actuator Mounting Sensor, Actuator Switch Screw, Socket Button Head (#10-3 x 1") NLA NLA - Screw, Phillips Pan Head (#4-40 x 3/8") 1 9 C Hardware, Tilt Mechanism D NLA NLA - Hardware, Non-Tilt 1 1 NOTE: A - Attaching hardware for the Actuator Switch Mounting Bracket consists of part numbers , , and P0870X000. B - Not Shown C - Includes Items 7-1, 15, 16, and 18-8 D - Includes Items 1-6 E - Part #'s and Tilt Lever is no longer available. Item #7 has been replaced with part #106009, available from Top End. Please contact Top End directly for this part that can be used on the right or left side of the wheelchair. 19

21 Orbit Seat Option Tilt and Non-Tilt Hardware 0

22 Item Number Note Part Number Description Orbit Seat Option Tilt and Non-Tilt Hardware Quantity Per Package Assembly Bolt, Shoulder (1/4 x 3/4") NLA NLA - Locknut (#10-4) NLA NLA - Screw, Shoulder Hex Socket Head (5/16" x 1 1-1/4", 1/4-0) Locknut (1/4-0) Link Washer, Nylon (3/8 x 7/8 x 1/16") Screw, Socket Button Head (1/4-0 x 1") Screw, Socket Button Head (1/4-0 x 1-1/4") Package, Locknut (1/4-0) Cable, Tilt Release Cable, Tilt - Left NLA NLA - Screw, Hex Head (5/16-18 x 1-1/") X00 Locknut (5/16-18) 1 13 D Screw, Socket Button Head (1/4-0 x 1-1/4") 1 1 B NLA NLA - Screw, Phillips Pan Head (#4-40 x 3/8") 1 1 B NLA NLA - Washer, Plain (1/8 x 5/16 x 1/3") 1 1 B P0870X000 Nut, Hex Keps (#4-40) NLA NLA - Bracket, Actuator Switch Mounting, Black Package, Locknut (1/4-0) NLA NLA - Washer, Plain (1/8 x 5/16 x 1/3") Washer, Nylon (1/4 x 1/ x 1/16") NLA NLA - Washer, Internal Tooth Lock (#4-40) NLA - Locknut (#4-40) Package, Locknut (1/4-0) Locknut, High Profile (#10-3) X003 Spacer (5/16 x 1/ x 3/8") NLA NLA - Plate, Actuator Mounting Sensor, Actuator Switch Screw, Socket Button Head (#10-3 x 1") NLA NLA - Screw, Phillips Pan Head (#4-40 x 3/8") Package, Tie Wrap (5-5/8" L) C Hardware, Tilt Mechanism A NLA NLA - Hardware, Non-Tilt 1 1 NOTE: A - Includes Items 1-6 B - Not Shown C - Includes items 7-1 and 16-7 D - Attaching hardware for the Actuator Switch Mounting Bracket consists of part numbers , , and P0870X000. 1

23 Lock Cylinder with Stop Assembly Item Number Note Part Number Description Quantity Per Package Assembly Lock Cylinder with Stop Assembly - Right Lock Cylinder with Stop Assembly - Left 1 1 A Locknut, High Profile (#10-3) NLA NLA - Bracket, Stop 1 4 A NLA NLA - Screw, Socket Button Head (#10-3 x 3/8") 1 NOTE: A - Left side includes 1

24 Solid Backs and Seats without Hardware Solid Backs without Hardware Chair Width 1" Height 13" Height 14" Height 15" Height 16" Height 17" Height 18" Height 1" Width " Width " Width " Width special special " Width special special NOTE: For back upholstery hardware, see the Solid Back Mounting Hardware page. Solid Seats without Hardware Chair Width 1" Depth 13" Depth 14" Depth 15" Depth 16" Depth 1" Width " Width " Width " Width NLA " Width Seat Hardware Part Number Description Quantity Required Screw, Socket Button Head (1/4-0 x 1-1/") 4 3

25 Solid Back Mounting Hardware Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Bushing, Pivot NLA NLA - Lever, Lock, Black - Right NLA NLA - Lever, Lock, Black - Left Washer, Spring (5/16 x 1/ x 1/16") NLA NLA - Screw, Button Head (1/4-0 x 5/8") NLA NLA - Mount, Lower Back - Right NLA NLA - Mount, Lower Back - Left 1 1 4

26 Orbit Seat Option Seat Rail, Lower Seat Plate Assembly 5

27 Item Number Note Part Number Description Orbit Seat Option Seat Rail, Lower Seat Plate Assembly Quantity Per Package Assembly 1 A NL NLA - Frame, Seat, Rail, Color 1 A Plug Button, Black (1") Package, Locknut (1/4-0) Tube, Spacer, Black NLA NLA - Plate, Lower Seat NLA NLA - Screw, Socket Flat Head (1/4-8 x 1-3/4") NLA NLA - Pin and Lanyard Assembly Spacer, Coved (1/4 x 11/16 x 1/") Tube, Slide, Seat Frame, Black X00 Spacer, Coved (1/4 x 1 x 9/16") Spacer (5/16 x 7/8 x 3/16") NLA NLA - Screw, Shoulder Hex Socket Head (1/4 x 1 1-3/4", #10-4) Washer, Nylon (1/4 x 1/ x 1/16") Washer, Nylon (3/16 x 7/16 x 1/8") NLA NLA - Locknut (#10-4) Screw, Socket Button Head (1/4-0 x 1-1/4") Locknut (1/4-8) NLA NLA - Washer, Flat (1/4 x 1/ x 1/16") B,C Hardware, Seat Mounting 1 1 NOTE: A - Specify frame color when ordering B - When converting to an Orbit seat, item 1 must be ordered as well. C - Includes items -18 6

28 Orbit Seat Option Foot Pedal Release Assembly 7

29 Item Number Note Part Number Description NOTE: Orbit Seat Option Foot Pedal Release Assembly Quantity Per Package Assembly Locknut (1/4-8) Washer (1/4 x 1/ x 1/16") Washer, Nylon (1/4 x 1/ x 1/3") Screw, Socket Button Head (1/4-8 x 3/4") NLA NLA - Plate, Mounting NLA NLA - Foot Lever Lock Assembly, Black NLA NLA - Pin, Locking NLA NLA - Pedal, Foot, Black NLA NLA - Bracket, Foot Pedal, Black NLA NLA - Bolt, Cable (Rear) NLA NLA - Bolt, Cable (Front) Spacer, Coved (1/4 x 11/16 x 1/") NLA NLA - Tilt Foot Lever Assembly 1 1 A Cable, Tilt Release 1 1 A Cable, Tilt - Left 1 1 A - Not Shown 8

30 Orbit Seat Option Seat Frame Assembly and Back Canes 9

31 Item Number Note Part Number Description Orbit Seat Option Seat Frame Assembly and Back Canes Quantity Per Package Assembly 1 A Cane, Back, Fixed Height, Black - Right/Left (18" H) Tip, Plastic, Black Lever, Actuator X00 Spacer, Coved (1/4 x 1 x 9/16") Locknut (1/4-8) Spring, Compression (5/8 x 1 x 3/64") Plug, Latch Washer (1/4 x 1/ x 1/16") See Chart Item #9 Crossmember Rail, Seat, Black - Right Rail, Seat, Black - Left Screw, Allen Head (1/4-8 x 1-1/4") Locknut (1/4-8) Screw, Hex Head w/ Patch (1/4-0 x ") Tube, Support, Front Rigging Hanger, Black - Right Tube, Support, Front Rigging Hanger, Black - Left Kit, Sector Block - Right Kit, Sector Block - Left B Upper Seat Plate Assembly and Mounting Hardware Screw, Hex Head (1/4-8 x 1-1/") Bracket, L, Black NLA NLA - Screw, Socket Flat Head (1/4-8 x 1/") Screw, Hex Head (1/4-8 x 1-3/4") Pin, Locking Screw, Hex Head (1/4-8 x ") Plug Button, Black (7/8") Screw, Set Socket (1/4-0 x 1/4") 1 5 See Chart Item #5 Spreader Bar Plate, Backrest Mounting Grip, Handle, Foam, Black (5") 1 NOTE: A - Item #7 Foam Handle Grip is not included B - Includes the Upper Seat Plate Assembly and items 8, 1 and

32 Orbit Seat Option Seat Frame Assembly and Back Canes Item #9 Crossmember 10" Wide 11" Wide 1" Wide 13" Wide 14" Wide 15" Wide 16" Wide NLA NLA Item #5 Spreader Bar 10" Wide 11" Wide 1" Wide 13" Wide 14" Wide 15" Wide 16" Wide NLA NLA

33 Orbit Seat Option Seat Pans Item Number Note Part Number Description 1 NOTE: A A - Not Shown Quantity Per Package Assembly Screw, Socket Button Head (1/4-0 x 1-1/") Locknut (1/4-0) 1 4 See Chart # Seat Pans 1 1 # Seat Pans 3

34 Orbit Seat Option Seat Pans # Seat Pans Seat Depth 10-13" 14-16" 10" Wide " Wide " Wide " Wide " Wide " Wide " Wide

35 Orbit Seat Option "T" Arm and Hardware 34

36 Item Number Note Part Number Description Orbit Seat Option "T" Arm and Hardware Quantity Per Package Assembly 1 B Pad, Arm, Desk Length - Right (9" L x " W) B Pad, Arm, Desk Length - Left (9" L x " W) B Pad, Arm, Full Length - Right (14" L x " W) B Pad, Arm, Full Length - Left (14" L x " W) Package, Screw Phillips Pan Head (#10-3 x 1-3/8") T-Arm Assembly w/ Plug Buttons, Desk Length, Low 1 1 Range, Black T-Arm Assembly w/ Plug Buttons, Full Length, Low 1 1 Range, Black Plug Button, Black (7/8") Post, Arm, Low Range D Kit, Clothing Guard, Low Range - Right D Kit, Clothing Guard, Low Range - Left Guard, Clothing, Low Range Tube, Support, Low Range, Black - Right NLA NLA - Tube, Support, Low Range, Black - Left Grip, Foam Locknut (#10-3) Lever, Locking Screw, Phillips Pan Head (#10-3 x 11/16") NLA NLA - Spring, Torsion Screw, Socket Button Head (1/4-0 x 1/") NLA NLA - Clamp, Clothing Guard - Right NLA NLA - Clamp, Clothing Guard - Left C Arm Socket Assembly, Bolt On A Nut, Hex (1/4-8) 1 18 A Washer (1/4 x 1/ x 1/16") Bracket, T-Arm Socket, Threaded, Black A Screw, Hex Head (1/4-8 x 1-3/4") Insert, Arm Socket, Black Screw, Socket Button Head (1/4-8 x 3/4") Lockwasher (1/4 x 15/3 x 1/64") NLA NLA - Bracket, Socket, Black 1 1 NOTE: A - Items 17, 18 and 0 must be ordered together for chairs manufactured before 8/13/99 due to a change in hardware. B - Specify U67 upholstery color when ordering. C - Includes items 17-4 D - Includes items

37 Orbit Seat Option Stroller Handles

38 Item Number Note Part Number Description Orbit Seat Option Stroller Handles Quantity Per Package Assembly 1 A,B NLA NLA - Stroller Handle Assembly (10-1") A,C NLA NLA - Stroller Handle Assembly (13-15") A,D Stroller Handle Assembly (16-18") Grip, Foam Hand (9" L) NLA NLA - Handle, Stroller, Black - Right NLA NLA - Handle, Stroller, Black - Left Locknut (#10-3) Pin, Quick Release with Lanyard NLA NLA - Tube, Insert Screw, Phillips Pan Head Tap (#10-3 x 1-1/4") 1 8 B NLA NLA - Link Assembly, Stroller Handle C NLA NLA - Link Assembly, Stroller Handle D Link Assembly, Stroller Handle 1 1 NOTE: A - Includes items - 8. B " Wide Chairs. C " Wide Chairs. D - 16" Wide Chairs. 37

39 Adjustable Height Arms 38

40 Item Number Note Part Number Description Adjustable Height Arms Quantity Per Package Assembly 1 A Pad, Arm, Vinyl, Desk Length (9" L x " W) A Pad, Arm, Vinyl, Full Length - Right (14" L x " W) A Pad, Arm, Vinyl, Full Length - Left (14" L x " W) Package, Screw, Phillips Pan Head (#10-3 x 5 1-1/8") Arm Tube Assembly w/ Plug Buttons, Desk Length, 1 1 Black - Right/Left NLA NLA - Tube, Arm, w/ Plug Buttons, Black, Full 1 1 Length Plug Button, Black (7/8") 1 5 B Adjustable Height Arm Base Assembly - Right 1 1 Base, Armrest, Adjustable Height Spring, Arm Lock Pin, Arm Lock, Black Rivet Guard, Clothing Kit, Lock Handle w/rivets (Pair) B Adjustable Height Arm Base Assembly - Left 1 1 Base, Armrest, Adjustable Height Spring, Arm Lock Pin, Arm Lock, Black Rivet Guard, Clothing Kit, Lock Handle w/rivets (Pair) NLA NLA - Socket, Arm, Rear C Package, Button Head Cap Screw (1/4-0 x 1-3/4") 5 1 D Screw, Socket Button Head (1/4-0X-1/4") 1 13 C Screw, Socket Button Head (1/4-0 x 1-1/") 1 13 D Screw, Socket Button Head (1/4-0 x ") X00 Spacer, Coved (1/4 x 1 x 9/16") Package, Locknut (1/4-0) NLA NLA - Spacer (9/3 x 7/8 x 1/") NLA NLA - Socket, Arm with Lock Handle, Front - Right NLA NLA - Socket, Arm with Lock Handle, Front - Left 1 1 NOTE: A - Specify upholstery color, U67 black vinyl, when ordering B - Stainless steel clothing guards were replaced with ABS plastic. Chairs manufactured before 7/30/97 should be ordered in pairs to match. C - All Chair Widths Except 14" D - For 14" Wide Chairs Only. 39

41 ATL4A Legrest Support Assembly 40

42 ATL4A Legrest Support Assembly Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Tube, Support and Drive Link, Chrome - Right NLA NLA - Tube, Support and Drive Link, Chrome - Left NLA NLA - Decal, Smartleg Screw, Hex Head (5/16-4 x 3-1/4") X003 Spacer (5/16 x 1/ x 3/8") Package, Locknut (5/16"-4) Washer (#0) X009 Bolt, Lug (5/16-4 x 1-3/8") Housing, Latch - Right Housing, Latch - Left Screw, Slotted Hex Washer Head (#10-3 x 5/8") Package, Screw, Slotted Hex Washer Head (# x 1/") Locknut (1/4-0) Plug Button, Black (1") Plug Button, Black (3/4") NLA NLA - Tube, Legrest Support, Articulating, Sector, 1 1 Chrome - Right NLA NLA - Tube, Legrest Support, Articulating, Sector, 1 1 Chrome - Left NLA NLA - Screw, Shoulder Slotted Head (1/ x 1-1/8", 1 1 3/8-16) X000 Hex Nut (3/8"-16) B Bracket, Legrest, Chrome X019 Plate, Legrest Pad Tube, Slide, Articulating, Chrome - Right Tube, Slide, Articulating, Chrome - Left NLA NLA - Screw, Socket Button Head (3/8-16 x 3/4") Washer, Nylon (3/8 x 3/4 x 1/16") Spacer, Legrest Pad, Black NLA NLA - Bar, Link, Chrome X003 Bushing, Pivot (5/16 x 7/16 x 7/8") X008 Spring, Leaf Pivot, Footrest Package, Button Head Cap Screw (1/4-0 x 1-3/4") A Articulating Legrest Support Assembly, Sector, 1 1 Chrome - Right 8 A Articulating Legrest Support Assembly, Sector, Chrome - Left 1 1 NOTE: A - Includes items 1-7 B - Right/Left 41

43 Swingaway Footrest Support Assemblies 4

44 Swingaway Footrest Support Assemblies Item Number Note Part Number Description Quantity Per Package Assembly Screw, Socket Button Head (1/4-0 x 1-3/4") Plug Button, Black (1") Pivot, Footrest Locknut (1/4-0) Screw, Slotted Hex Washer Head (#10-3 x 5/8") Screw, Slotted Hex Washer Head w/ Patch (# x 1/") Housing, Latch - Right Housing, Latch - Left Collar, Anti-Rattle A Footrest Support Assembly, 60 Degree, Sector, 1 1 Color - Right 9 A Footrest Support Assembly, 60 Degree, Sector, 1 1 Color - Left 9 A Footrest Support Assembly, 60 Degree MFX, 1 1 Sector, Color - Right 9 A Footrest Support Assembly, 60 Degree MFX, 1 1 Sector, Color - Left 9 A Footrest Support Assembly, 70 Degree 1 1 Non-Tapered, Sector, Color - Right 9 A Footrest Support Assembly, 70 Degree 1 1 Non-Tapered, Sector, Color - Left 9 A Footrest Support Assembly, 90 Degree, Sector, 1 1 Color - Right 9 A Footrest Support Assembly, 90 Degree, Sector, 1 1 Color - Left 10 A Kit, 3" Extension w/ Hardware (Pair) B Kit, Pivot/Slide Tube Mounting Hardware (Pair) B Screw, Hex Head w/ Patch (1/4-0 x 3/4") B Spacer, Coved (1/4 x 11/16 x 1/") B,C Insert, Threaded 1 1 NOTE: A - Specify frame color when ordering B - Attaching hardware for pivot slide tube C - As of 8/15/03, the Threaded Insert was revised from 3 to 5 Holes. Threaded Insert is Backward Compatible and does not require ordering in Pairs. 43

45 Calf Pads and Ratchet Assemblies Due to a change to the Legrest Calf Pad size made on 4/3/1, you must also order the hardware kit ( ) when ordering replacement Calf Pads. 44

46 Calf Pads and Ratchet Assemblies Due to a change to the Legrest Calf Pad size made on 4/3/1, you must also order the hardware kit ( ) when ordering replacement Calf Pads. Item Number Note Part Number Description Quantity Per Package Assembly 1 A,B,D, F Pad w/ Cover and Screws, Legrest Vinyl (Pair) 1 1 A,C,D, F Pad, Legrest, Vinyl - Right/Left X000-NLA NLA - Cover, Legrest Pad X019 Plate, Legrest Pad Spacer, Legrest Pad, Black E Hardware, Legrest Pad 1 1 Screw, Phillips Pan Head (#10-3 x 11/16") 1 Screw, Phillips Pan Head (#10-3 x 1") 1 Instruction Sheet, Legrest Pad Mtg X008 Spring, Leaf Package, Locknut (5/16"-4) Bracket, Legrest, Chrome Screw, Hex Head (5/16-4 x 3-1/4") Tip, Plastic, Black Washer, Nylon (5/16 x 11/16 x 1/16") X004 Bar, Ratchet - Right/Left X003 Bushing, Pivot (5/16 x 7/16 x 7/8") Ring, Snap Cam, Legrest Spring, Release Nut, Acorn (5/16-4) X00 Bracket, Release, Chrome Handle, Release Kit, Elevating Legrest Ratchet Hardware (Pair) 1 NOTE: A - Specify upholstery color when ordering. B - Before 9/5/00 (pair) C - After 9/4/00 (single) D - 16" Wide E - Includes Screws and Instruction Sheet. F - Due to a change to the Legrest Calf Pad size made on 4/3/1, you must also order the hardware kit ( ) when ordering replacement Calf Pads. 45

47 AT5043 Flip-Up Footplates 90deg Swingaway Supports NOTE: Heel loops are not included. See footrest and legrest accessories. Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Footplate, Black (4-1/4" W x 5-1/4" L) (1" W) NLA NLA - Washer, Nylon (3/16 x 3/4 x 5/3") Spacer, Coved (1/4 x 3/4 x 11/3") Plug Button, Black (3/4") Screw, Socket Button Head (10-3 x 1-1/4") Screw, Socket Button Head (1/4-0 x 1-1/") NLA NLA - Screw, Socket Button Head (1/4-0 x -5/8") NLA NLA - Tube, Footrest, Black NLA NLA - Cam, Adjustment X00 Spacer, Coved (1/4 x 1 x 9/16") Locknut (1/4-0) Washer (1/4 x 5/8 x 3/3") NLA NLA - Flip-Up Footplate Assembly, Black - Right NLA NLA - Flip-Up Footplate Assembly, Black - Left

48 AT5543 Adjustable Angle Footplates 60deg and 70deg Swingaway Supports - Before 3/1/95 NOTE: Heel loops are not included. See footrest and legrest accessories. 47

49 AT5543 Adjustable Angle Footplates 60deg and 70deg Swingaway Supports - Before 3/1/95 NOTE: Heel loops are not included. See footrest and legrest accessories. Item Number Note Part Number Description Quantity Per Package Assembly Screw, Socket Flat Head (1/4-0 x 3/4") 1 A Footplate, Black (4-1/4" W x 7-1/" L) (1-13" W) 1 1 B NLA NLA - Footplate, Black (5-1/4" W x 7-1/" L) (14-16" 1 1 W) Half Clamp, Threaded Plug Button, Black (3/4") Washer (1/4 x 5/8 x 3/3") NLA NLA - Cam, Adjustment NLA NLA - Tube, Pivot/Slide, Straight - Alum. (9-7/8" L) Spacer, Coved (1/4 x 3/4 x 11/3") Screw, Shoulder Hex Socket Head (1/4" x ", 1 1 #10-4) Screw, Socket Button Head (1/4-0 x 1") Half Clamp, Non-Threaded NLA NLA - Tube, Footrest, Black Screw, Socket Button Head (1/4-0 x 1-1/") Locknut (1/4-0) A,C NLA NLA - Hardware, Footplate Assembly - Right A,C NLA NLA - Hardware, Footplate Assembly - Left B,C NLA NLA - Hardware, Footplate Assembly - Right B,C NLA NLA - Hardware, Footplate Assembly - Left 1 1 NOTE: A - 1"-14" Wide B - 15"-16" Wide C - For complete adjustable angle footplates see "AT5543 Adjustable Angle Footplates - After /8/95" page. 48

50 AT5543 Adjustable Angle Footplates ATL4A, 60deg, 70deg, 70deg MFX & 90deg Swingaway Supports After /8/95 NOTE: Heel loops are not included. See footrest and legrest accessories. 49

51 AT5543 Adjustable Angle Footplates ATL4A, 60deg, 70deg, 70deg MFX & 90deg Swingaway Supports After /8/95 NOTE: Heel loops are not included. See footrest and legrest accessories. Item Number Note Part Number Description Quantity Per Package Assembly 1 A See Chart Pivot Slide Tube w/ Footplate Assemblies 1 1 B,F Footplate, Adjustable Angle, Small, Black (3-1/4" W 1 1 x 8" L) C,F Footplate, Adjustable Angle, Medium, Black (4-1/4" 1 1 W x 8" L) D,F Footplate, Adjustable Angle, Large, Black (5-1/4" W 1 1 x 8" L) 3 E Clamp, Footplate Tube, Pivot and Slide, Straight, Steel, Black (9-7/8" 1 1 L) Tube, Pivot/Slide, Straight, Steel, Black (11-7/8" L) Tube, Pivot/Slide, Straight, Steel, Chrome (13-7/8" 1 1 L) Screw, Nylon Adjustment (1/-13 x 7/8") Hinge, Footplate - Right Hinge, Footplate - Left E Screw, Socket Flat Head (1/4-0 x 3/4") Package, Screw, Socket Button Head (1/4-0 x /8") Washer (1/4 x 3/3 x 1/16") Package, Washer, Nylon (5/16 x 7/8 x 1/8") Washer, Nylon (1/4 x 7/8 x 1/3") Spacer, Coved (1/4 x 3/4 x 11/3") Spacer, Coved (1/4 x 11/16 x 1/") Washer (1/4 x 1/ x 1/16") Locknut (1/4-0) E Nut, Barrel, Hex Head (1/4-0 x 11/16") 1 NOTE: A - Includes Items thru 16. B - For 10-11" wide chairs C - For 1-13" wide chairs D - For 14-16" wide chairs E - Items 3, 7 and 16 must be ordered together for chairs manufactured before 8/10/99 due to a hardware change. F - This footplate was revised 9//008 with rounder corners and accessory holes changed from 8 to 4. Recommended to replace the footplate in pairs to match sides. #1 Pivot Slide Tube w/ Footplate Assemblies Rigging Type 90, 70MFX (9-7/8" Tube) 60, 70 Swingaway (9-7/8" Tube) 60, 70 Swingaway (11-7/8" Tube) ATL4A Swingaway (13-7/8" Tube) See Note(s) A 50

52 AT5543 Adjustable Angle Footplates ATL4A, 60deg, 70deg, 70deg MFX & 90deg Swingaway Supports After /8/95 NOTE: Heel loops are not included. See footrest and legrest accessories. #1 Pivot Slide Tube w/ Footplate Assemblies Rigging Type 90, 70MFX (9-7/8" Tube) 60, 70 Swingaway (9-7/8" Tube) 60, 70 Swingaway (11-7/8" Tube) ATL4A Swingaway (13-7/8" Tube) See Note(s) A 10-11" W - Right (3-1/4" Footplate) NLA NLA 10-11" W - Left (3-1/4" Footplate) NLA NLA " W - Right (4-1/4" Footplate) " W - Left (4-1/4" Footplate) " W - Right (5-1/4" Footplate) See Note(s) A 14-16" W - Left (5-1/4" Footplate) See Note(s) A NOTE: A - ALT4A Smart Legs are offered in 16 inch wide models only. 51

53 Pivot/Slide Tube and Composite Footplates NOTE: Heel loops are not included. See footrest and legrest accessories. NOTE: Heel loops are not included. See footrest and legrest accessories. 5

54 Pivot/Slide Tube and Composite Footplates NOTE: Heel loops are not included. See footrest and legrest accessories. Item Number Note Part Number Description Quantity Per Package Assembly 1 C Tube, Pivot/Slide, Curved End, Black - Short 1 1 (8-1/4") 1 D Tube, Pivot/Slide, Curved End, Black - Long (9-7/8") D Tube, Pivot/Slide, Curved, " Longer, Black 1 1 (11-7/8") 1 E NLA NLA - Tube, Pivot/Slide, Straight - Alum. (9-7/8" L) E Tube, Pivot/Slide, Straight - Black (11-7/8" L) Spacer, Coved (1/4 x 3/4 x 11/3") Plug Button, Black (3/4") Package, Locknut (1/4-0) Package, Socket Head Screw (1/4-0 x -1/4") A Footplate, Composite, Small, Black (6" W x 6" L) B Footplate, Composite, Medium, Black (7" W x 6" L) See Chart #7 Pivot/Slide Tube w/composite Footplate Assemblies 1 1 NOTE: A " Wide B " Wide C - 60 Degree MFX D - 60 Degree E - 70 Degree NTaper #7 Pivot/Slide Tube w/composite Footplate Assemblies (without Heel Loops) Front Rigging 60 Degree (13"-19") -Right 60 Degree (13"-19") -Left 60 Degree (13"-19") " Longer -Right 60 Degree (13"-19") " Longer -Left 60 Degree MFX (9-3/4" - 14") -Right 60 Degree MFX (9-3/4" - 14") -Left 70 Degree (14"-19") -Right 70 Degree (14"-19") -Left 70 Degree (14"-19") " Longer -Right 70 Degree (14"-19") " Longer -Left Small 13"-14" Wide NLA NLA NLA NLA NLA NLA Medium 15"-16" Wide NLA NLA

55 One Piece Adjustable Angle Footboard Item Number Note Part Number Description Quantity Per Package Assembly 1 A Footboard B NLA NLA - Footboard NLA NLA - Clamp, Footplate 1 3 A NLA NLA - Footrest Support Assembly, Black B NLA NLA - Footrest Support Assembly, Black Half Clamp, Threaded Screw, Socket Flat Head (1/4-0 x 3/4") Half Clamp, Non-Threaded Screw, Socket Button Head (1/4-0 x 1") NLA NLA - Tab, Weldment, Black Washer, Nylon (1/4 x 1/ x 1/16") Package, Locknut (1/4-0) A NLA NLA - Footrest Support Assembly, Black B Footrest Support Assembly, Black A NLA NLA - Footboard Assembly, One Piece Adjustable 1 1 Angle 1 B Footboard Assembly, One Piece Adjustable Angle 1 1 NOTE: A " Wide Chairs B " Wide Chairs 54

56 Footrest and Legrest Accessories Item Number Note Part Number Description NOTE: Quantity Per Package Assembly B Strap, Calf w/ Hook and Loop (6" L) 1 1 C Strap, Calf w/ Hook and Loop (36" L) 1 1 A Kit, 3" Extension w/ Hardware (Pair) 1 D See Chart Footplate Type 1 1 D See Chart AT5543 Heel Loops and Hardware 1 1 D See Chart Toe Loops and Attaching Hardware 1 1 A - Specify frame color when ordering. B " Wide C " Wide D - Not Shown Footplate Type Composite (1651) Footplate Small 13-14" Wide Medium 15-16" Wide Heel Loop Single # NLA Heel Loop Pair # Heel Loop w/ Ankle Strap Right - Single # NLA Heel Loop w/ Ankle Strap Left - Single # NLA Heel Loop w/ Ankle Strap Pair # Attaching Hardware Pair # AT5543 Heel Loops and Hardware Footplate Type Part Number Consists of: AT5543 Footplate AT5543 Footplate Attaching Hardware Only Kit, Heel Loop w/ Hardware, Adjustable Angle Footplate (Pair) Kit, Heel Loop w/ Ankle Strap and Hardware, Adjustable Angle Footplate (Pair) Kit, Heel Loop Attaching Hardware (Pair) () Heel Loops (4) Screw, Phillips Pan Head (1/4-0 x -1/4") (4) Spacer (4) Locknut (1/4-0) () Heel Loops w/ Ankle Straps (4) Screw, Phillips Pan Head (1/4-0 x -1/4") (4) Spacer (4) Locknut (1/4-0) () Screw, Phillips Pan Head (1/4-0 x -1/4") () Spacer (1/4 x 11/3 x 1-3/4") () Hex Nut w/ Nylon Cap (1/4-0) () Flat Washer (1/4 x 5/8 x 1/16") 55

57 Footrest and Legrest Accessories Toe Loops and Attaching Hardware Toe Loops (1345) All Sizes Footplate Attaching Hardware 1651 Footplate AT5043 and AT5543 Footplates Toe Loop Single # 0457X05 Part Number Hardware, Toe Loop (Pair) Hardware, Toe Loops and Footplate (Pair) Toe Loop Pair # Consists of: (4) Screw, Phillips Pan Head (10-3 x 7/8") (4) Washer (1/4 x 3/4 x 3/3") (4) Locknut (10-3) (4) Screw, Phillips Pan Head (10-3 x 1/") (4) Washer (1/4 x 3/4 x 3/3") 56

58 Side Frames and Hardware 57

59 Item Number Note Part Number Description Side Frames and Hardware Quantity Per Package Assembly Screw, Socket Button Head (1/4-0 x 1-1/4") Plug Button, Black (7/8") X01 Collar, Anti-Rattle (7/8") Package, Locknut (1/4-0) Tube, Seat Rail, Color NLA NLA - Tube, Slide, Front, Black NLA NLA - Tube, Rear Slide, Black 1 8 A NL NLA - Frame, Front, Color - Right 1 1 A 8 A NL NLA - Frame, Front, Color - Left 1 1 A 9 A,B Frame, Side, Color - Right A,B Frame, Side, Color - Left 1 1 NOTE: A - Specify frame color when ordering. B - Decals not included with frame. 58

60 Frame Width Growth Kits NOTE: Frame width growth kits listed are for power Tiger seats only. To widen an Orbit seat, see seat frame under Orbit seat option. NOTE: Front Rigging Footplates may be needed when growing a chair. Original Width 13" New Width 14" New Width 15" New Width 16" New Width 1" NLA NLA See Note(s) A See Note(s) B See Note(s) B 13" NLA NLA See Note(s) B See Note(s) B 14" NLA NLA See Note(s) B See Note(s) B 15" See Note(s) A NOTE: A - Only wider upholstery is required. B - Specify frame color when ordering. Individual Hardware For Growth Kits Part Number Description NLA Spacer Tube, 4" (for 16" Wide Frame) NLA Spacer Tube " (for 14" Wide Handle) Spacer Tube 4" (for 16" Wide Handle) 1099-NLA Release Rod Slide Tube, Seat Frame NLA Slide Tube, Cane Handgrip Seat Rail Tube See Note(s) A (15"-16" Wide) Washer (9/3 x 7/8 x 3/16") NLA Spacer (9/3 x 7/8 x 1/") Spacer (1/4 x 1/ x 7/3") Screw (1/4-0 x -1/4") NLA Locknut (10-4) NLA Shoulder Bolt (1/4 x 1-3/4") Washer (1/4 x 1/ x 1/16") Washer (7/3 x 7/16 x 1/8") 59

61 Frame Width Growth Kits NOTE: Frame width growth kits listed are for power Tiger seats only. To widen an Orbit seat, see seat frame under Orbit seat option. NOTE: Front Rigging Footplates may be needed when growing a chair. Individual Hardware For Growth Kits Part Number Description NLA NOTE: Screw (1/4-0 x ") 40157X00 Spacer, Coved (1") Screw (Pkg of 5) (1/4-0 x 1-3/4") Screw (1/4-0 x 1-1/") A - Specify frame color when ordering

62 6" and 8" Casters 61

63 Item Number Note Part Number Description 6" and 8" Casters Quantity Per Package Assembly Cap, Head Tube, Black Package, Head Tube Cap X000 Locknut (7/16-0) X044 Washer, Nylon (7/16 x 1 x 1/8") Bearing (7/16") X030-NLA NLA - Sleeve, Aluminum Bearing, Sleeve, Lower D Mounting, Caster Fork B Fork and Stem, Black (6") B,E Fork and Stem, Color (6") B NLA NLA - Fork and Stem, Black (8") Locknut (7/16-0) Spacer (7/16 x 5/8 x 3/16") Screw, Hex Head (7/16-0 x 3-1/4") 1 1 L Washer, Steel (15/3 x 5/8 x 3/64") 1 1 F Washer, Steel (15/3 x 5/8 x 3/64") G NLA NLA - Hardware, Caster, Standard Fork 1 13 H Hardware, Caster Axle (Pair) 1 13 I NLA NLA - Hardware, Caster 1 14 J 40117X04 Bearing (1-3/8" O.D. x 7/16" I.D.) K Bearing (7/16") Spacer, Bearing (7/16 x 5/8 x 1-3/4") C,N,N NLA NLA - Wheel Assembly, Semi-Pneumatic, Urethane 1 1 (6" x ") 16 O Wheel Assembly, Semi-Pneumatic, Urethane, Deep 1 1 Profile, Grey Tire/Black Hub (6" x ") 16 O Wheel Assembly, Semi-Pneumatic, Urethane, Deep 1 Profile, Grey Tire/Black Hub (6" x ") (Pair) 16 A Wheel Assembly, Semi-Pneumatic, Urethane, Light 1 1 Grey (8" x 1-3/4") Wheel Assembly w/ Bearings, Pneumatic (8" x ") X034 Tire, Pneumatic (8" x ") Tube, Pneumatic Inner (8 x ") 1 1 M Wheel Assembly, Semi-Pneumatic, Urethane, Light Grey (8" x 1-3/4") (Pair) 1 6

64 NOTE: 6" and 8" Casters A - For chairs manufactured before 6/9/97, order in pairs (Pair # ). B - Fork design changed 10/5/98. For chairs manufactured before 10/5/98, order in pairs to match. C - For chairs manufactured before 6/4/97, order in pairs and new caster hardware dated after 6/3/97. D - Includes items 1-6 E - Specify color when ordering. F - 8" Casters G - 6" Fork (Before 6/4/97) Per Side H - 6" Fork (After 6/3/97) One Pair I - 8" Fork, One Pair J - 6" Casters (Before 6/4/97) K - 8" Casters and (6" Casters After 6/3/97) L - 6" Casters (After 6/3/97) M - Not Shown N - Service part No Longer Available 8/15/03. Due to product improvement, order (pair) part number dated after 8/14/03 so each side matches. The deep profile caster has tread grooves w/ round corners instead of 4 tread grooves w/ square corners. N1 - For chairs manufactured before 6/4/97, order new caster hardware dated after 6/3/97 as well. O - For chairs made after 8/14/03 63

65 Rear Wheels and Motor Mounting Hardware 64

66 Rear Wheels and Motor Mounting Hardware Item Number Note Part Number Description Quantity Per Package Assembly Wheel, Drive 5 Spoke, Pneumatic (1-1/ x -1/4") 1 1 Includes: Locking Tab Washer with Instruction Sheet Wheel, Drive 5 Spoke w/ Foam Fill Insert (1-1/ x 1 1-1/4") Includes: Locking Tab Washer with Instruction Sheet Tire, Pneumatic, Grey (1-1/" x -1/4") Tube, Inner, Black (1-1/ x -1/4") A NLA NLA - Insert, Flat Free NLA NLA - Rim with Locking Tab Screw (M8 x 1.5 x 0mm) Kit, Locking Tab Washer w/ Instruction Sheet (Pair) Washer (11/3 x 13/16 x 1/8") Key (6mm x 6mm x 40mm) B NLA NLA - Clamp, Motor Half C Clamp, Motor Half Screw, Socket Head Cap (M6 x 1 x 40mm) B,D NLA NLA - Screw, Socket Head (M6 x 5MM) C NLA NLA - Screw, Socket Head (M6 x 30mm) NLA NLA - Cap, Motor Clamp, Black Screw, Allen Head (1/4-0 x 1") Anti-Tipper, Rear 1 1 NOTE: A - As of 10/0/99 the "solid" flat free insert was replaced by a "foam fill" process. When a Flat Free Insert is requested, a complete wheel must be ordered. B - Before 6/9/06 C - After 6/8/06 D - No Longer Available. 65

67 Motor/Gearbox Assembly 66

68 Item Number Note Part Number Description Motor/Gearbox Assembly Quantity Per Package Assembly 1 A Motor/Gearbox Assembly with Brake - Right A Motor/Gearbox Assembly with Brake - Left A Motor/Gearbox Assembly with Brake 1 1 B,C Motor/Gearbox Assembly with Brake - Right B,C Motor/Gearbox Assembly with Brake - Left D Motor/Gearbox Assembly with Brake - Right D Motor/Gearbox Assembly with Brake - Left 1 1 A,D NLA NLA - Brake, Spring Set with Screws A,D NLA NLA - Kit, Motor/Brake Covers with Screws 1 4 A,D Kit, Motor Brush w/o Cap - Internal, Long Cap (Pair) 1 4 B Kit, Motor Brush w/ Cap - External (Pair) Instruction Sheet, Motor Brush Kit 1 1 NOTE: A - Before 6/9/06 B - 6/9/06-10/15/06 C - Brakes and Brake Covers are non-serviceable for the Motor/Gearboxes built 6/9/06 thru 10/15/06 with external brushes D - After 10/15/06 for MK6i electronics. 67

69 Wheel Locks and Hardware 68

70 Item Number Note Part Number Description Wheel Locks and Hardware Quantity Per Package Assembly 1 A,C NLA NLA - Wheel Lock Assembly - Right A,C NLA NLA - Wheel Lock Assembly - Left D Wheel Lock Assembly - Right D Wheel Lock Assembly - Left Package, Rubber Tip, Wheel Lock Handle, Black B Kit, Wheel Lock Attaching Hardware 1 4 Bolt, Hex Head Cap (1/4-0 x 3/4") 1 5 Washer (1/4 x 5/8 x 3/3") 1 NOTE: A - Wheel lock handle design changed after /17/99. Chairs manufactured before /18/99, order in pairs to match. These wheel locks were used /18/99-6/8/06 B - Item 3 is a pair number that includes ea. of items 4 and 5 C - Before 6/9/06. No Longer Available, order a pair of Wheel Locks dated after 6/8/06 D - After 6/8/06 69

71 Battery Boxes and Tray Assembly MKIV Electronics 70

72 Battery Boxes and Tray Assembly MKIV Electronics Item Number Note Part Number Description Quantity Per Package Assembly 1 A,B,C, F NLA NLA - Battery Box Top Assembly 1 A,F Battery Box Bottom with Strap, NF 1 3 F Battery Box Assembly Package, Locknut (1/4-0) Package, Button Head Cap Screw (1/4-0 x 1-3/4") NLA NLA - Tray, Battery with Buckle Strap Screw, Socket Button Head (1/4-0 x 1-1/4") X019 Spacer, Coved (1/4 x 7/8 x 7/16") Washer (1/4 x 5/8 x 3/3") 1 B,E,G 50000X166-NLA NLA - Fuse - Buss -1/4" L (60 AMP) 1 E,H Fuse, MIDI (Non-G/B & G/B) (80 AMP) 1 D,E Hardware, Battery Terminal, NF Batteries (Pair) 1 NOTE: A - Battery boxes built before 8/1/96 are no longer available. When replacing a battery box top or bottom for chairs built before 8/1/96, both parts must be replaced. See item 3. B - As of 1/15/99 the battery harness fuse changed from a Bussman 60 AMP. to a MIDI 80 AMP. fuse. This battery box top is compatible for all chairs manufactured before 11/5/99 and must be ordered whenever a replacement Bussman 60 AMP. fuse is requested. C - It is recommended that terminal hdwr. part # for NF batteries be ordered when a new battery box top is ordered. D - Hardware inlcudes battery clamps, battery clamp caps (red and black), small battery terminal caps (red and black), 1/4-0 x 7/8" hex flange screws, 1/4-0 hex flange nuts, cable ties and locking tab washers for two batteries. E - Not Shown. F - After 7/31/96 G - Before 11/5/99 H - After 11/4/99 71

73 Battery Boxes and Tray Assembly MK6i Electronics 7

74 Battery Boxes and Tray Assembly MK6i Electronics Item Number Note Part Number Description Quantity Per Package Assembly 1 A Top, Battery Box, Front, NF A Battery Box Top, Rear, NF 1 1 C Fuse, MIDI (Non-G/B & G/B) (80 AMP) Battery Box Bottom with Strap, NF 1 1 C NLA NLA - Strap, Battery 1 1 C NLA NLA - Pin, Handle 1 3 B Battery Box Assembly, Front, NF B Battery Box Assembly, Rear, NF Locknut (1/4-0) Screw, Socket Button Head (1/4-0 x 1-3/4") NLA NLA - Tray, Battery with Buckle Strap Screw, Socket Button Head (1/4-0 x 1-1/4") X019 Spacer, Coved (1/4 x 7/8 x 7/16") Washer (1/4 x 5/8 x 3/3") 1 C,D Hardware, Battery Terminal, NF Batteries (Pair) 1 NOTE: A - It is recommended that terminal hdwr. part # for NF batteries be ordered when a new battery box top is ordered. B - Includes Battery Box Top and Bottom (items 1 and ). C - Not Shown. D - Hardware inlcudes battery clamps, battery clamp caps (red and black), small battery terminal caps (red and black), 1/4-0 x 7/8" hex flange screws, 1/4-0 hex flange nuts, cable ties and locking tab washers for two batteries. 73

75 Wiring Harnesses and Chargers MKIV Electronics 74

76 Item Number Note Part Number Description 1 C A 14 A J 14 J 15 I,I K 19 0 F,G 0 H 1 G 1 H D D B,E B,E 3 Wiring Harnesses and Chargers MKIV Electronics Quantity Per Package Assembly NLA NLA - Hardware, Harness Mounting Rivet, Snap X403-NLA NLA - Clamp, Black Plastic Package, Tie Wrap (11-1/" L) NLA - Locknut (#4-40) NLA NLA - Washer, Internal Tooth Lock (#4-40) NLA NLA - Washer, Plain (1/8 x 5/16 x 1/3") NLA NLA - Screw, Phillips Pan Head (#4-40 x 3/8") 1 P0870X000 Nut, Hex Keps (#4-40) Screw, Socket Button Head (1/4-0 x 1-1/") NLA NLA - Bracket, Charger Connector, Black Screw, Phillips Pan Head (#4-40 x 1/") Locknut (1/4-0) Charger, Battery, 8 Amp, 115vac, Off Board, 1 1 Dual Mode, Square Plug, Lester Charger, Battery, 8 Amp, 115vac, Off Board 1 1 Dual Mode Round Plug, Lester NLA NLA - Charger, Battery, 8 Amp. 115vac, Off Board, 1 1 Dual Mode, Round Plug w/ AC Power Line Cord, Dynamic Charger, Battery, 8 Amp. 115vac (Off Board) 1 1 Single Mode Round Plug w/ AC Power Line Cord, CTE Corp E WARR RPLMT - Charger, Battery, 8 Amp, 115VAC 1 1 (Off Board) Single Mode Round Plug w/ AC Power Line Cord, CTE Corp Battery Charger, 8 Amp. 115vac (Off Board) 1 1 Single Mode Round Plug w/ AC Power Line Cord and Square Plug Adapter Cable, CTE Corp Cord, AC Power, 115VAC, Prong Off-Board (11' 1 1 6" L) Cable, Adapter 1 1 See Note See Footnote Cable, Charger Extension, Round Plug (4" L) Fuse - Buss ATC-15 (15 AMP) Fuse - Buss Mini ATM-15 (15 AMP) NLA NLA - Fuse, Buss ATC-0 (0 AMP) NLA NLA - Fuse - Buss Mini ATM-0 (0 AMP) NLA NLA - Harness, Wiring, Square Charger Plug, Tilt NLA NLA - Harness, Wiring, Square Charger Plug, 1 1 Non-Tilt Harness, Wiring, Round Charger Plug, Tilt Harness, Wiring, Round Charger Plug, Non-Tilt NLA NLA - Wrap, Slit Wire Harness (1/" O.D., 36" Long 1 1 Cut To Length) 75

77 Item Number Note Part Number Description 4 5 NOTE: Wiring Harnesses and Chargers MKIV Electronics Quantity Per Package Assembly Fuse - Buss Mini ATM-15 (15 AMP) Cable, Drive Lockout Sensor 1 1 A - On 7/18/01 Lester 8 amp. battery chargers were reinstated. The square plug model was offered on chairs made before /0/95. B - On 8/6/0 a (PTO) power take off connector was added to the wire harness. Item 4 sensor cable is included with the tilt wire harness part number C - Includes items -13 D - Before /0/95 E - After /19/95 F - The wire harness takes a quantity of fuses G - Before 4/1/03 H - After 3/31/03 I - CTE charger introduced and standard on-chair 4/1/04. Used on Gel Cell or AGM (Absorbed Glass Mat) batteries. For wet cell batteries refer to the Lester charger. I1 - CTE charger looks exactly the same as Dynamic's charger except for the company name that is silk screened on the narrow side panel, where the charger plug is (hard wired) attached. Serial number starts with 04A J - CTE charger without the square plug adapter cord is for chairs equipped with a round plug charger connector K - No longer available as a service part. 76

78 Wiring Harnesses and Chargers MK6i Electronics 77

79 Item Number Note Part Number Description Wiring Harnesses and Chargers MK6i Electronics Quantity Per Package Assembly NLA NLA - Screw, Phillips Pan Head (#4-40 x 3/8") NLA NLA - Washer, Plain (1/8 x 5/16 x 1/3") NLA NLA - Washer, Internal Tooth Lock (#4-40) NLA - Locknut (#4-40) Cable, Drive Lockout Sensor, MK6i Package, Tie Wrap (11-1/" L) A Charger, Battery, 8 Amp. 115vac (Off Board) 1 1 Single Mode Round Plug w/ AC Power Line Cord, CTE Corp. 7 A 11349E WARR RPLMT - Charger, Battery, 8 Amp, 115VAC 1 1 (Off Board) Single Mode Round Plug w/ AC Power Line Cord, CTE Corp Cord, AC Power, 115VAC, Prong Off-Board (11' 6" L) 1 1 NOTE: A - Battery charger includes AC Power Line Cord (item 8). 78

80 MK6i Electronics 79

81 MKIV Joysticks RII, RX, A, A+, TCHJOY 80

82 Item Number Note Part Number Description NOTE: MKIV Joysticks RII, RX, A, A+, TCHJOY Quantity Per Package Assembly A,C NLA NLA - Joystick/Controller, MKIV RII 1 1 B Controller, MKIV RII, Retro 1 1 B Programmer, Remote 1 1 B See Chart MKIV Joysticks 1 1 A - For chairs made before 5/1/00, the following must be ordered, RII Joystick part #(109610), RII Retro Controller Part #(109569) and Remote Programmer part #( ) B - Not Shown C - For joystick inductive and switch components, refer to chart under RII joystick assembly part number Item Number Description RII RX A A Before 9/1/96 After 8/31/96 A+ TCHJOY See Pictorial Joystick Assembly NLA Knob, Joystick Skirt, Joystick Inductive, NLA NLA NLA NLA NLA Joystick See Note(s) B See Note(s) C See Note(s) B See Note(s) C See Note(s) B 3 Inductive, Joystick See Note(s) D See Note(s) D 4 Boot, Joystick 50000X X X X X364 Overlay, NLA 5 Joystick NLA Decal See Note(s) A 6 Cable Assembly See Note(s) A See Note(s) C See Note(s) B See Note(s) C See Note(s) B 6 Cable Assembly See Note(s) D See Note(s) D Potentiometer , Speed See Note(s) B See Note(s) C See Note(s) C Potentiometer , Speed See Note(s) D See Note(s) D 8 Knob, Potentiometer Switch, On/Off Momentary See Note(s) B See Note(s) C See Note(s) B Switch, On/Off Momentary See Note(s) D 81

83 MKIV Joysticks RII, RX, A, A+, TCHJOY A A Item Number Description RII RX A+ TCHJOY Before 9/1/96 After 8/31/ Switch, Off/ 1- Switch, Off/ See Note(s) C NLA See Note(s) D Switch, Program See Note(s) B Switch, Toggle SPDT See Note(s) B NOTE: A - Cable assembly and joystick overlay decal for RII joystick before 10/01/0 and after 9/30/0 are not available. B - Item requires soldering C - Before 10/01/0 item requires soldering D - After 9/30/0 item has a non-solder connector. 8

84 MKIV Joystick PS, PSF and PSR NOTE: PSR STANDARD joystick configuration below show the on/off switch on the left side for part # When the on/off switch is required on the right side, refer to part number and order as a configurated part. 83

85 MKIV Joystick PS, PSF and PSR NOTE: PSR STANDARD joystick configuration below show the on/off switch on the left side for part # When the on/off switch is required on the right side, refer to part number and order as a configurated part. Item Number See Pictorial See Pictorial See Pictorial See Pictorial See Pictorial Description Joystick Assembly Joystick Assembly Joystick Assembly Joystick Assembly Joystick Assembly Knob, Joystick Skirt, Joystick Inductive, Joystick Boot, Joystick Overlay, Joystick Decal Cable Assembly Potentiometer Speed Knob Potentiometer Switch, On/Off Momentary Switch, Push Button SPST Momentary Switch, Push Button SPST Boot, Switch Boot, Switch PS Before 1/1/ NLA NLA 50000X NLA PSF After 11/30/ NLA NLA 50000X NLA NLA PSR After 11/30/ NLA NLA NLA NLA 50000X NLA NLA NLA

86 MKIV Joystick Mounting Hardware and Joystick Accessories 85

87 MKIV Joystick Mounting Hardware and Joystick Accessories Item Number Note Part Number Description Quantity Per Package Assembly 1 A Kit, Straight Joystick Tube with Hardware B Kit, Straight Joystick Tube with Hardware C Kit, Straight Joystick Tube with Hardware 1 1 D,D1,E Kit, 1/" Offset Joystick Tube with Hardware F Plug Button, Black (7/8") Screw, Phillips Pan Head (#4-40 x 3/8") Package, Tie Wrap (11-1/" L) Spacer, Joystick Tube, Black Package, Screw, Phillips Pan Head (#10-3 x /8") 8 G Hardware, Joystick Tube Mounting D,D1,H Clamp, Fixed Height Joystick Tube I Clamp, Height Adjustable Joystick Tube (ARM50) Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black X004-NLA NLA - Screw, Hex Head (1/4-0 x 1-1/8") Kit, Toggle Switch Extension Screw, Phillips Round Head (#10-3 x 3/8") 1 3 J Extension, Joystick, "T" Style (1560) 1 1 (4" W x 5-1/" L) J Extension, Joystick, Straight Style (1561) (1/" W x 5" L) 1 1 NOTE: A - For TCHJOY Touch Pad "A" or TCPDM4 Touch Pad Joystick and includes the joystick tube, items 3 and 4 B - For PS joystick before 1/1/97 and includes the joystick tube, items 3 and 16 C - For MKIV RII, RX, A, A+, PSF/PSR joysticks before 10/4/00 and includes the joystick tube, items 3 and 5-7 D - The joystick straight tube changed to an offset joystick tube on 10/4/00. The joystick tube mounting hardware also changed to a new fixed height clamp assembly to allow an individual to use an D1 - adjustment lever to securely hold the joystick tube in place. The fixed height joystick tube clamp can be used as a direct replacement in the field for the joystick tube mounting hardware part number manufactured for chairs before 10/4/00. E - For MKIV RII, RX, A, A+, PSF/PSR joysticks after 10/3/00 and includes the offset joystick tube, items 3 and 5-7 F - The Touch Pad joystick tube takes a quantity of plug buttons G - For (PS joystick before 1/1/97), TCHJOY and MKIV RII, RX, A, A+, PSF/PSR joystick before 10/4/00 and includes items H - For MKIV RII, RX, A, A+, PSF/PSR joystick after 10/3/00. Individual components are non-saleable I - Introduced 10/31/05 as option (ARM50) and can be used to replace a Fixed Height Joystick Tube Clamp in the field. Individual components are non-saleable J - Not Shown 86

88 MKIV Swivel Joystick Hardware Item Number Note Part Number Description Quantity Per Package Assembly Spacer, Joystick Tube, Black Package, Screw, Phillips Pan Head (#10-3 x /8") NLA NLA - Bracket, Swivel Joystick, MKIV NLA NLA - Bracket, Swivel Joystick with Hardware NLA NLA - Joystick Swivel Tube with Hardware, Black Washer, Flat (1/4 x 3/8 x 1/16") Bushing NLA NLA - Spring, Hitch Bracket NLA NLA - Knob, Clamping, Grey NLA NLA - Tube, Swivel Joystick, Black Plug Button, Black (7/8")

89 MKIV Mid-Line Swing Bracket Assembly NOTE: Joystick tube with 90 degree bend replaces the standard tube when joysticks PSF, PSR and (RII part number ) are used. Joystick Tube with 90 degree bend must be ordered as a special when a replacement is needed. 88

90 MKIV Mid-Line Swing Bracket Assembly NOTE: Joystick tube with 90 degree bend replaces the standard tube when joysticks PSF, PSR and (RII part number ) are used. Joystick Tube with 90 degree bend must be ordered as a special when a replacement is needed. Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Tube, Adjustment, Inside, Mid-Line, Black NLA NLA - Spring, Extension (9/16 x 1-3/8" L) NLA NLA - Tube, Adjustment, Outside, Mid-Line, Black Adjustment Lock Assemnbly, Black A Swing Bracket Assembly, Mid-Line, Black Screw, Hex Head (1/4-0 x 1-1/8") Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes B Hardware, Joystick Tube Mounting 1 1 C Joystick, RII 1 1 NOTE: A - Includes items 1-4 B - Includes items 6-10 C - Not Shown 89

91 Quad Link Assembly Before 10/31/05 90

92 Item Number Note Part Number Description 1 A A B,E B Quad Link Assembly Before 10/31/05 Quantity Per Package Assembly Kit, Quad Link Assembly - Right 1 1 Ball Plunger Assembly with Lock Washer 1 Locknut (#10-3) 1 NLA - Screw, Cap, Socket Head (#10-3 x 1/") 1 4 Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Screw, Phillips Pan Head (#10-3 x 1-1/8") 1 4 Spacer, Joystick Tube, Black 1 1 Stud Plate, Quad Link 1 1 Screw, Hex Head (1/4-0 x 1-1/") 1 3 Spacer (1/4 x 3/8 x 3/16") 1 3 Half Clamp, Non-Threaded Holes 1 1 Half Clamp, Threaded Holes Kit, Quad Link Assembly - Left 1 1 Ball Plunger Assembly with Lock Washer 1 Locknut (#10-3) 1 NLA - Screw, Cap, Socket Head (#10-3 x 1/") 1 4 Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Screw, Phillips Pan Head (#10-3 x 1-1/8") 1 4 Spacer, Joystick Tube, Black 1 1 Stud Plate, Quad Link 1 1 Screw, Hex Head (1/4-0 x 1-1/") 1 3 Spacer (1/4 x 3/8 x 3/16") 1 3 Half Clamp, Non-Threaded Holes 1 1 Half Clamp, Threaded Holes NLA Kit, Quad Link Assembly - Right 1 1 Ball Plunger Assembly with Lock Washer 1 Locknut (#10-3) 1 NLA - Screw, Cap, Socket Head (#10-3 x 1/") 1 4 Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Plate, Stud, Quad Link For 1556 Heavy Duty 1 1 Joystick Screw, Hex Head (1/4-0 x 1-1/") 1 3 Spacer (1/4 x 3/8 x 3/16") 1 3 Half Clamp, Non-Threaded Holes 1 1 Half Clamp, Threaded Holes 1 1 Screw, Phillips Flat Head (#10-3 x 1-1/8") NLA - Kit, Quad Link Assembly - Left 1 1 Ball Plunger Assembly with Lock Washer 1 Locknut (#10-3) 1 NLA - Screw, Cap, Socket Head (#10-3 x 1/") 1 4 Bushing, Bronze (3/16 x 1/4 x 1/4") 1 4 Plate, Stud, Quad Link For 1556 Heavy Duty 1 1 Joystick 91

93 Item Number Note Part Number Description Quad Link Assembly Before 10/31/05 Quantity Per Package Assembly 9 Screw, Hex Head (1/4-0 x 1-1/") Spacer (1/4 x 3/8 x 3/16") Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes Screw, Phillips Flat Head (#10-3 x 1-1/8") 1 1 C NLA NLA - Kit, Quad Link Assembly - Right 1 1 For TCHJOY/TCPDM4 Touchpad Ball Plunger Assembly with Lock Washer 1 3 Locknut (#10-3) 1 4 NLA - Screw, Cap, Socket Head (#10-3 x 1/") Bushing, Bronze (3/16 x 1/4 x 1/4") Screw, Phillips Pan Head (#10-3 x 1-1/8") 1 8 NLA - Plate, Stud, Quad Link 1 1 MKIV TCHJOY/TCPDM4 9 Screw, Hex Head (1/4-0 x 1-1/") Spacer (1/4 x 3/8 x 3/16") Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes NLA - Screw, Phillips Flat Head Countersunk (# x 3/8") 1 D NLA NLA - Kit, Quad Link Assembly - Right 1 1 For PS joystick Ball Plunger Assembly with Lock Washer 1 3 Locknut (#10-3) 1 4 NLA - Screw, Cap, Socket Head (#10-3 x 1/") Bushing, Bronze (3/16 x 1/4 x 1/4") NLA - Plate, Stud, Quad Link 1 1 P.S. Joystick 9 Screw, Hex Head (1/4-0 x 1-1/") Spacer (1/4 x 3/8 x 3/16") Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes Screw, Phillips Pan Head (#10-3 x 11/16") Ball Plunger Assembly with Lock Washer 1 NOTE: A - Includes the Quad Link, items -1 and used with MKIV RII, RX, A, A+, PSF/PSR joysticks B - Includes the Quad Link, items -5, 8-13 and used with a 1556 Heavy Duty joystick C - Includes the Quad Link, items -6, 8-1, 14 and used with MKIV TCHJOY/TCPDM4 joysticks. For left side mounted Quad Link, order as a special. D - Includes the Quad Link, items -5, 8-1, 15 and used with a PS joystick E - Quad Link Assembly is no longer available. Please see Quad Link Assembly (After 10/30/05) category and use new Quad LInk design as a replacement. 9

94 Quad Link (QLA) After 10/30/05 When converting an old style Quad Link that attaches to a mounting plate or (a Flex Tube or Touch Pad Joystick Tube) is currently on the chair then order the following: Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) NOTE: Substitute (item 4) with ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD Touch Pad joystick are used. 93

95 Quad Link (QLA) After 10/30/05 When converting an old style Quad Link that attaches to a mounting plate or (a Flex Tube or Touch Pad Joystick Tube) is currently on the chair then order the following: Quad Link Mtg. Hdwr. (item 4), Quad Link (item 1) & Ht. Adj. Joystick Tube Clamp (item 11) NOTE: Substitute (item 4) with ea. of the PPH Screws (item 5) when an offset joystick tube is currently on the chair. Additional Joystick Mtg. Hdwr. must be ordered when a 1556 Heavy Duty or TCPD Touch Pad joystick are used. Item Number Note Part Number Description Quantity Per Package Assembly Quad Link w/ Adjustable Joystick Tray (QLA) and 1 1 Instruction Sheet - Right Quad Link w/ Adjustable Joystick Tray (QLA) and 1 1 Instruction Sheet - Left A Kit, Quad Link Latch Hardware B Kit, Quad Link Screw Fastener Hardware C,C Kit, ASBA/ADJASBA Quad Link Mounting Hardware Screw, Phillips Pan Head w/ Patch (#10-3 x 3/4") 1 6 Screw, Phillips Pan Head (#10-3 x 1-1/8") 1 7 Tie Wrap (11-1/" L) Spacer, Joystick Tube, Black Tube, Joystick Offset (1/") Plug Button, Black (7/8") Screw, Phillips Pan Head w/ Patch (#10-3 x 3/4") 1 11 G Clamp, Height Adjustable Joystick Tube (ARM50) D NLA Kit, 1556 Heavy Duty Joystick To Quad Link 1 1 Mounting Hardware 13 Screw, Phillips Pan Head (#10-3 x 1/") 1 14 NLA - Plate, 1556 HD Joystick Quad Link E Kit, TCPD Touch Pad To Quad Link Mounting 1 1 Hardware 16 Plate, TCPD Touch Pad Quad Link Screw, Phillips Pan Head (#4-40 x 3/8") 1 4 F Instruction Sheet, Quad Link 1 1 NOTE: A - Latch Kit includes 4 ea. Button Head Cap Screws (10-3 x 3/8"), ea. Latch Spring Assembly, 4 ea. Phillips Flat C'Sunk Head Screws, ea. Spring Catch Plates, ea. Socket Head Set Screws (10-3 x 3/8") B - Screw Fastener Kit includes 4 ea. Socket Head Shoulder Screws (3/8 x 3/8"), ea. Socket Head Cap Screws (1/4-0 x 3/8"), ea. Socket Head Set Screws (1/4-0 x 1/"), 4 ea. Socket Head Set Screws (10-3 x 1/8") C - Includes items The Quad Link Mounting Hardware accommodates MKIV RII, RX, A, A+, PSF/PSR joysticks. C1 - When ordering the Quad Link for the first time, Additional hardware is required for 1556 Heavy Duty and TCPD Touch Pad joysticks. See pictorial for reference. D - Includes items 13 and 14 E - Includes items 16 and 17 F - Not Shown G - Individual components are non-saleable 94

96 MKIV Controller, Programmer and Attaching Hardware 95

97 MKIV Controller, Programmer and Attaching Hardware Item Number Note Part Number Description Quantity Per Package Assembly Controller, MKIV Quad Pulse B,G Controller, MKIV RII, Retro Package, Screw, Hex Head w/ Patch (5/16-18 x 5 1-1/4") Locknut (5/16-18) Washer (1/4 x 5/8 x 3/3") Screw, Socket Button Head (1/4-0 x 1-1/") X019 Spacer, Coved (1/4 x 7/8 x 7/16") Package, Locknut (1/4-0) NLA NLA - Bracket, Controller Mounting, Black 1 9 H Programmer, Remote I Switch, Red Flex Ribbon (Tape) Reset A,J Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) C NLA NLA - Hardware, Controller 1 1 A,D NLA NLA - Virtual Service Modem Kit 1 1 A,E NLA NLA - Virtual Service Software Kit 1 1 A,D NLA NLA - MKIV One One Software Kit 1 1 A,F NLA NLA - Printer and Interface 1 1 A Cable, Virtual Service, Charger/Modem 1 1 A NLA NLA - Disk, 3.5 H.D. Floppy with V.S. Software 1 1 A NLA NLA - Adaptor, Null Modem 1 1 A NLA NLA - Service Manual - V.S. Software Kit 1 1 A NLA NLA - Paper, Printer 1 1 A NLA NLA - Harness, Printer Wiring 1 1 NOTE: A - Not Shown B - After 4/30/00 C - Includes Items -8 D - Part number is available for individual sale. E - Part numbers , , , and are available for individual sale. F - Part numbers and are available for individual sale. G - RII retro controller after 4/30/00 and RII joystick part number (109610) are direct replacements for joystick/controller part number (108073). H - Remote Programmer part number ( ) with the dual connectors (3-Pin and 5-Pin) is the only programmer functionable with the new RII joystick part number (109610). I - Before 5/4/04 J - Not Shown. After 5/3/04 the Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch 96

98 MKIV Sip-N-Puff/Digital Interface and COM1 and COM34 97

99 MKIV Sip-N-Puff/Digital Interface and COM1 and COM34 Item Number Note Part Number Description Quantity Per Package Assembly NLA NLA - Sip-N-Puff w/ Digital Interface D See Note See Footnote NLA NLA - Module, Communication, COM34/AUX A Kit, COM1/AUX1 and COM34/AUX34 Mounting 1 1 Hardware 1 Half Clamp, Threaded Holes 1 1 Half Clamp, Non-Threaded Holes NLA - Screw, Hex Head (1/4-0 x 1-1/8") 1 4 NLA - Fastener, Dual Lock Hook and Loop 1 1 Adhesive (" W x 1" L) 5 Plate, COM1/AUX1 and COM34/AUX Mounting 11 B,C Kit, SNP/DI, MK5 SAC, 4WSB, S4WSB, GTAM, 1 1 AUX1M6, AUX34M6 Mtg. Hdwr. 1 Half Clamp, Threaded Holes 1 1 Half Clamp, Non-Threaded Holes NLA - Screw, Hex Head (1/4-0 x 1-1/8") 1 6 Screw, Phillips Pan Head (#4-40 x 3/8") 1 7 Plate, Mounting 1 1 NOTE: A - Mounting hardware includes items 1-5. Item 4 that is packaged with the kit will only be a 4" long "loop" fastener. Hook and Loop Fastener replaced the screws shown when the holes were removed from the communication module 7/1/97 B - Includes items 1-3 and 6-7 C - As of 5//07 the Mounting Plate holes and the orientation of the Hardware was revised to attach the electronics closer to the chair. The Mounting Hardware Kit is backward compatible. D - Part is no longer serviceable in the field. 98

100 MKIV Displays 99

101 Item Number Note Part Number Description MKIV Displays Quantity Per Package Assembly NLA NLA - Display without Switches Display with Switches A Tube, Flex with Screws Screw, Phillips Pan Head (#4-40 x 3/8") B Hardware, Joystick Tube Mounting Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black X004-NLA NLA - Screw, Hex Head (1/4-0 x 1-1/8") C Clamp, Fixed Height Joystick Tube F Clamp, Height Adjustable Joystick Tube (ARM50) D Switch, Red Flex Ribbon (Tape) Reset E Kit, Switch, Black Egg Reset w/ Hook/Loop Adhesive Back Fastener & Attaching Screws (EGSBLK) 1 1 NOTE: A - Includes the Flex Tube and item 4 B - Before 10/4/00 and includes items 6-10 C - After 10/3/00 and can be used as a direct replacement for the Joystick Tube Mounting Hardware part number in the field D - Before 5/4/04 E - After 5/3/04 the Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch F - Introduced 10/31/05 as option (ARM50) and can be used to replace a Fixed Height Joystick Tube Clamp in the field. Individual components are non-saleable 100

102 MKIV R.I.M. Head Control Assembly (1500) (Before 8/16/95) 101

103 MKIV R.I.M. Head Control Assembly (1500) (Before 8/16/95) Item Number Note Part Number Description Quantity Per Package Assembly Rod, Cushion NLA NLA - Bar, Control NLA NLA - Block, Bearing E Switch, Toggle SPDT Tie Rod End NLA NLA - Switch, Hi / Lo / Off (Black) NLA NLA - Handle, Rim Control X003-NLA NLA - Clip, Spring, Rotor NLA NLA - Bearing, Pillow Block NLA NLA - Rod, Pivot A NLA NLA - Push Rod Assembly NLA NLA - Guard, Axle Ribbon Reset Switch and Bracket Assembly Bearing, Linear NLA NLA - Joystick, Remote NLA NLA - Rod, Joystick Mounting X001 Locknut (5/16-4) NLA NLA - Bracket, Rod Mounting, Black NLA NLA - Bracket, Upright, Black -Right Bracket, Upright, Black - Left Adjustment Lock Assemnbly, Black X009 Bolt, Lug (5/16-4 x 1-3/8") 1 1 B NLA NLA - Tube, Support Upright C NLA NLA - Tube, Support, Upright, Black D NLA NLA - Tube, Support, Upright, Black 1 1 B NLA NLA - Hardware Assembly, Rim Control 1 1 C NLA NLA - Hardware Assembly, Rim Control 1 1 D NLA NLA - Hardware Assembly, Rim Control Tube, Flex with Screws Screw, Phillips Pan Head (#4-40 x 3/8") NLA NLA - Display without Switches 1 1 NOTE: A - Includes: push rod cap, collar with set screw, spring push rod, nut, and tie rod end. B - 1" Wide Chairs C - 14" Wide Chairs D - 16" Wide Chairs E - Black Switch is no longer available. The Chrome Switch part number serves as a direct replacement 10

104 MKIV R.I.M. Head Control Mounting Hardware (1500M4) (After 8/15/95) 103

105 MKIV R.I.M. Head Control Mounting Hardware (1500M4) (After 8/15/95) Item Number Note Part Number Description Quantity Per Package Assembly 1 A Cover, Nylon NLA NLA - Clamp with Knob, Two-Piece Screw, Socket Button Head (#10-3 x 3/4") Package, Screw, Hex Head (1/4-0 x 3/4") A NLA NLA - Bracket, Attaching, Black (1-18" W) Screws with Washers (#10-16 x 7/8") Screw w/ Washer (#10 x 7/8") NLA NLA - Bracket, Wing, Black Washer (1/4 x 1/ x 1/16") Locknut (1/4-0) Washer, Nylon (3/16 x 7/16 x 1/8") Locknut, High Profile (#10-3) A Hardware, Rim Control Mounting (RIMHW) (1-18" W) 1 1 NOTE: A " Wide 104

106 MKIV R.I.M. Head Control Assembly (1500M4) (After 8/15/95) 105

107 MKIV R.I.M. Head Control Assembly (1500M4) (After 8/15/95) Item Number Note Part Number Description A B C 38 D E Quantity Per Package Assembly Tie Rod End X000 Locknut (#10-3) NLA NLA - Screw, Set w/ Patch (#8-3 x 1/4") O-Ring (1/" I.D.) Screw, Phillips Pan Head (#8-3 x 3/8") NLA NLA - Washer, Nylon Block, Pivot NLA NLA - Ring, Snap Bearing, Linear NLA NLA - Shield, Push Rod Screw, Phillips Pan Head (#4-40 x 1/") NLA NLA - Bracket, Headrest Mounting, Black X00-NLA NLA - Screw, Phillips Oval Head (#10-3 x 3/4") NLA NLA - Spring, Compression (19/3 x 1-1/4 x 1/3") NLA NLA - Rod, Push NLA NLA - Screw, Phillips Pan Head (#6-3 x 1/4") Washer, Nylon (1/4 x 1/ x 1/16") NLA NLA - Collar, Shoulder X364 Boot, Joystick NLA NLA - Rod, Pivot X014 Screw, Phillips Round Head (#10-3 x 1") NLA NLA - Tie Wrap (4-1/4" L) Cover, Splash Washer, Plain (1/ x 1 x 1/8") Ribbon Reset Switch and Bracket Assembly E-NLA NLA - Reconditioned - Joystick, Remote Head NLA NLA - Clamp, Horizontal Pivot NLA NLA - Clamp, Threaded, Horizontal Pivot NLA NLA - Screw, Socket Head (M6 x 1 x 5mm) Tube, Slide, Square, Short NLA NLA - Clamp, Vertical Pivot NLA NLA - Clamp, Threaded, Vertical Pivot NLA NLA - Tube, Slide, Square, Long Hardware, Adjustment Screw, Socket Button Head (#10-3 x 1") NLA NLA - Washer, Lock Tooth (3/16 x 3/8 x 1/3") Kit, Headrest with Hardware, Otto Bock, Small Kit, Headrest with Hardware, Large NLA NLA - Screw, Socket Head (#10-3 x 1/")

108 NOTE: MKIV R.I.M. Head Control Assembly (1500M4) (After 8/15/95) A - Includes items 1-5. B - Includes items 7-33 and the Plug Buttons that attach to item 30 and 33 Slide Tubes. The Plug Buttons are not saleable. C - Includes the Headrest Adapter and items 35 and 36. D - Includes the Headrest Adapter and items 35 and 36. The LaBac Headrest is no longer used as of 1/6/10 that was attached with Screw part # (4 ea.). The screw is still available to order for existing LaBac Headrest in the field. E - Used for existing LaBac Headrest in the field only. 107

109 MKIV Joystick Options 108

110 Item Number Note Part Number Description 1 N A B C D E 8 9 O F G H 4 I 43 J MKIV Joystick Options Quantity Per Package Assembly See Note See Footnote NLA NLA - Clamp, Universal Swivel X000 Handle, Lock, Chrome X000 Locknut (1/4-0) Joystick Tube with Plug Button Assembly Plug Button, Black (7/8") Joystick, Attendant Control (155M) NLA NLA - Joystick, Heavy Duty Kit, Straight Joystick Tube with Hardware Screw, Phillips Round Head (#10-3 x 3/8") Plug Button, Black (7/8") Hardware, Rear Cane Mount (1673/RCM) Plug Button, Black (7/8") Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Upright, Black -Right NLA NLA - Tube, Joystick Screw w/ Washer (#10 x 7/8") Tube, Arm Mount with Plug Button, Black Plug Button, Black (7/8") NLA NLA - Joystick, MKIV Dual/Compact Hardware, Dual/Compact Joystick Clamp Mounting Clamp Screw, Socket Button Head (#10-3 x 5/16") NLA NLA - Clamp, Mounting NLA NLA - Screw, Socket Head (#10-4 x 1/") NLA NLA - Spacer, Split (3/8" I.D.) Chin Cup Assembly Cup, Chin NLA NLA - Screw, Adaptor X000 Screw, Set Socket Cup Point (#8-3 x 1/4") NLA NLA - Touchpad, Joystick Assembly Kit, Straight Joystick Tube with Hardware Plug Button, Black (7/8") Screw, Phillips Pan Head (#4-40 x 3/8") Hardware, Joystick Tube Mounting Half Clamp, Threaded Holes Half Clamp, Non-Threaded Holes Adjustment Lock Assemnbly, Black NLA NLA - Bracket, Joystick Mounting, Black X004-NLA NLA - Screw, Hex Head (1/4-0 x 1-1/8") Clamp, Fixed Height Joystick Tube Clamp, Height Adjustable Joystick Tube (ARM50) Switch, Red Flex Ribbon (Tape) Reset

111 Item Number Note Part Number Description MKIV Joystick Options Quantity Per Package Assembly 44 K Kit, Switch, Black Egg Reset w/ Hook/Loop 1 1 Adhesive Back Fastener & Attaching Screws (EGSBLK) L Display with Switches 1 1 M NLA NLA - Display without Switches 1 1 NOTE: A - Includes the joystick tube and items 10 and 11 B - Includes items C - For On-Chair model numbers 1678 and Includes the joystick tube and item 19 D - Includes items -6 E - Includes items 8-30 F - Includes the joystick tube, items 33 and 34 G - Before 10/4/00 and includes items H - After 10/3/00. Individual components are non-saleable. Can be used as a direct replacement in the field for the Joystick Tube Mounting Hardware part number I - Introduced 10/31/05 as option (ARM50) and can be used to replace a Fixed Height Joystick Tube Clamp in the field. Individual components are non-saleable J - Before 5/4/04 K - After 5/3/04. The Egg Reset Switch replaced the Red Flex Ribbon (Tape) Reset Switch L - Not Shown and used with the Heavy Duty and Touch Pad Joystick M - Not Shown and used with the Remote Joystick N - No longer available as a service part in the field. O - Part # is no longer available as a service part individually. Order item #7 as a replacement. 110

112 Tash and Therafin Accessories 111

113 Item Number Note Part Number Description NOTE: Tash and Therafin Accessories Therafin (Not Shown) Quantity Per Package Assembly P580-NLA NLA - Switch, Red Soft 1 1 P581 NLA - Switch, Green Soft 1 1 B P5018 Wafer Board (5018) 1 1 B P506-NLA NLA - Star Control 1 1 B P500 Mini Joystick with Push (500) 1 1 P4337-NLA NLA - Multi-Ability Cable 1 1 P4353-NLA NLA - CA5 Multi-Connector Box 1 1 C Bib Assembly (PKG3669) 1 1 C P1456-NLA NLA - Adaptor Clamp - Tash 1 1 C P1457 Adaptor Clamp - Invacare 1 1 C P1460 Midline Swingway System 1 1 A,C Sip-N-Puff, 16" Fixed (PKG3666) Includes: (3) Air Tube Straws, () Saliva Traps, Tubing, Pivot Shaft/Flexible Metal Gooseneck Assembly, and Extruded Figure "8" Clamp to fit 7/8" Wheelchair Frame Tubing. Extruded Back Cane Adapter Clamp. 1 1 A - Includes 3 air tube straws, saliva traps, tubing, pivot shaft/flexible metal gooseneck assembly and extruded figure 8 clamp to fit 7/8" wheelchair frame tubing. B - Must be used with display with switches ( ) C - Not Shown NOTE: For more information on Tash and Therafin products, please contact one of our Rehab Specialists. 11

114 MK6i IR Wireless Mouse Module 113

115 Item Number Note Part Number Description MK6i IR Wireless Mouse Module Quantity Per Package Assembly 1 A,C See Note See Footnote D See Note See Footnote Emmitter, IR, Single Head B Kit, Switch, Dual Push Button (PB) (MPJ+, MK6i 1 1 Display, PSFM6/PSRM6 Joysticks) 5 Switch, Push Button Dual Hook, Material Loop, Material 1 1 NOTE: A - Includes items -11, tie wraps and owner's manual. B - Includes items 5, 7 and 8 C - Item #1 IR Mouse Mounting Assembly w/ Clamp Kit is no longer available as a serviceable kit. D - Item #3 IR Mouse Module Assembly is no longer available as a service part. 114

116 MK6i RF Wireless Mouse Module 115

117 MK6i RF Wireless Mouse Module Item Number Note Part Number Description Quantity Per Package Assembly 1 A RF Mouse Mounting Assembly w/ Clamp 1 1 NLA - Screw, Hex Head (1/4-0 x 1-1/8") 1 3 RF Mouse Module Assembly (63" L) Switch, Push Button Dual USB, IR/RF Mouse Dongle, Programmed Hook, Material Loop, Material Half Clamp, Non-Threaded Holes Half Clamp, Threaded Holes 1 1 Tie Wrap (5-5/8" L) 1 5 Owner's Manual, RF Mouse RF Mouse Module Assembly (63" L) B Kit, Switch, Dual Push Button (PB) (MPJ+, MK6i 1 1 Display, PSFM6/PSRM6 Joysticks) 4 Switch, Push Button Dual Hook, Material Loop, Material 1 1 NOTE: A - Includes items -9, tie wraps and owner's manual. B - Includes items 4, 6 and 7 116

118 Power Wheelchair Tool Kit 117

119 Item Number Note Part Number Description NLA Power Wheelchair Tool Kit NLA - Kit, Power Wheelchair Tool Includes: 1 ea. Multimeter with Leads 1 ea. Locator, Protractor/Angle Magnetic Base 1 ea. Instructions, MKIV Programmer 1 ea. Wire, Grounding with Hand Strap and Clip 1 ea. Leads, 1" Test 1 ea. Light, Pen with Invacare Logo 1 ea. Tape Measure, Compact with Invacare Logo 1 ea. Screwdriver, Pen-Size Phillips/Flat Head 1 ea. Cable, Virtual Service Charger/Modem Quantity Per Package Assembly

120 Miscellaneous Accessories Positioning Straps NOTE: Description Chair Width 1"-15" Wide Chair Width 16" Wide Auto Style Push Button See Note(s) A Airline Style Hook and Loop (Chest Only) A - 1"-15" wide positioning straps come in rainbow color. Item Number Note Part Number Description NOTE: Quantity Per Package Assembly A 40176X010 Pump, Tire 1 1 A See Chart Miscellaneous Accessories 1 1 A - Not Shown 119

121 Warranty Replacement Parts NOTE: Part Number Description Quantity per Assembly WARR RPLMT - Charger, Battery, E Amp, 115VAC (Off Board) Single Mode Round Plug w/ AC 1 See Note(s) A, B Power Line Cord, CTE Corp. A - See "Wiring Harness & Chargers - MKIV Electronics" Category for more information. B - See "Wiring Harness & Chargers - MK6i Electronics" Category for more information. 10

122 Invacare Corporation One Invacare Way Elyria, Oh USA Technical Support Florida Technical Support Customer Service Invacare Corporation. All rights reserved. Republication, duplication or modification in whole or in part is prohibited without prior written permission from Invacare. Trademarks are identified by and. All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted. (Revised 05/01/14)