FIST-GR3 ODF System Featuring Quareo Technology 2015 ORDERING GUIDE 4TH EDITION

Transcription

1 ODF System 2015 ORDERING GUIDE 4TH EDITION

2

3 Contents Quareo Physical Layer Management System 4 Quareo Middleware 5 Quareo Software 6 FIST-GR3 Rack 7 FIST-GPS Shelf featuring Quareo Technology (FIST-GPSQ) 7 Connection Point Identification (CPID) 7 Adapter Packs and Modules 7 Quareo Rack Controller 7 Example Application of a Two Rack Cross Connect 8 FIST-GPSQ Shelf Featuring Quareo Technology (FIST-GPSQ) 9 Benefits of Tray Patching 10 FIST-GPSQ Standard Kit Content 11 MPO Modules 13 Adapter Packs 15 FIST-GR3 Rack 16 Dimensions 17 Racks 17 Quareo Rack Controller 19 Quareo Managed Patch Leads and Multi-Fiber Cable Assemblies 20

4 Quareo Physical Layer Management System Businesses and organizations worldwide are more dependent on their physical layer than ever before. From computers, phones and wireless devices, to alarm systems, security cameras and video conferencing, today s network physical layer touches virtually every device inside an organization. Security of the physical layer also has become a top concern among network and data center managers, especially in healthcare, financial and mission-critical organizations where data is required to be secure. CommScope s Quareo physical layer management system, with its Quareo Connection Point Identification (CPID) hardware technology, delivers full knowledge and visibility of the physical layer. These solutions enable higher network availability, while lowering network costs, by integrating full visibility of the physical layer into existing network management applications all the way from the data center to the desktop. Quareo is helping network and data center managers bridge the gap between network management and physical layer management, transforming the physical layer into a strategic asset and revolutionizing the way networks are managed and controlled. By providing a real-time comprehensive picture of every connection point in the physical layer, physical layer management significantly improves productivity and efficiency of physical layer management and maintenance processes while reducing costly downtime and operating costs. For more information on the Quareo physical layer management system, visit 4 For more information, visit

5 Quareo Middleware The Quareo system is an Automated Infrastructure Management (AIM) platform which leverages a common middleware to drive and collect port level information from Quareo (CPID enabled) hardware. The Middleware approach and architecture of the Quareo system allows customers the flexibility to use the automated hardware to augment and leverage existing physical layer documentation, connection level details to support logic determinations, 3rd party management software platforms and custom use cases. The Quareo middleware API can host multiple connections to various software systems allowing for consistent, uniform updates of the physical layer connectivity information. The same Quareo Middleware drives communications for the purpose built Quareo Software GUI as a stand-alone tool. Automated port status: Quareo Hardware (CPID enabled) in combination with Quareo Middleware provides the automated port status of whether a port is vacant and available for use or populated with a patch cord. When Quareo Cables are used, the cable assembly information is provided with the port status information. Quareo Assemblies have unique serial numbers assigned in manufacturing which is programmed into the CPID along with PN and other details pertinent to the assembly/component. This CPID information allows correlation of the serial numbers to positively validate both ends/ports of the patch connection, and align system requirements/parameters (e.g.: circuit length budgets, Color coding, polarity, performance categories, etc.). LED Controls: Quareo (CPID) enabled equipment ports have bi-color LEDs for use in works orders and guidance as indicators. Within a change control process the identified ports for connection or removal of a cable assembly can have the LEDs turned on with appropriate colors and flash patterns, identifying the ports for either insertion or removal of cables, eliminating guesswork by field technicians, providing a reliable identification of the ports involved in the work actions. Use Cases DBMS Auto Documentation and Updates 3rd PARTY APPLICATION (DCIM, NMS) Port level Activity Monitoring Port level Security Port Status HTTP REST API(s) SNMP MIB(s) Port Level Details CPID Work Task Change Control processes Connectivity Management Circuit Level Integrity Quareo Device Quareo Device Discovery management Cable Assembly Details QUAREO MIDDLEWARE LAYER QUAREO ENABLED Assembly Serial Number DEVICES Correlation VIA HTTP Change control indicators LED Guidance 5 For more information, visit

6 Quareo Software The Quareo Software GUI supported by the Quareo Middleware is a purpose-built, stand-alone, server software application designed to document and administer both passive and active network connectivity infrastructure. The Quareo software enables management of various levels of network components from existing brownfield infrastructure to CommScope s traditional and automated physical layer management solutions. As part of the Quareo physical layer management system, Quareo software enables immediate notification and response to changes in connectivity and automatically records the configurations of the physical layer cabling system and its devices with accurate documentation. Features Accountability of assets by location and date Availability of assets and utilization is improved Reduced operational costs Best practice and regulatory requirements are more easily attained Network problems are more easily diagnosed and corrected Security is greatly enhanced Remote visibility of the physical layer DoD/DISA/JITC tested 6 For more information, visit

7 FIST-GR3 Rack All-purpose, easy-to-assemble FIST-GR3 racks accommodate the FIST fiber management system. The racks allow superior management and storage of pigtail and patch cord overlengths. The rack offers flexible shelf spacing and accepts a range of accessories such as panels and doors to complete the installation. The rack houses the FIST-GPSQ shelves for splicing and patching. The rack also houses the rack controller to manage the FIST-GPSQ shelves. FIST-GPS Shelf featuring Quareo Technology (FIST-GPSQ) The FIST-GPSQ shelves feature the FIST fiber management system and provide a platform for patching and splicing within a rack environment, using the Quareo physical layer management technology. The shelves house FIST splice and patch trays with Quareo CPID enabled adapter packs. The shelves mount in FIST-GR3 racks. Connection Point Identification (CPID) CommScope s CPID technology provides a unique identifier for every Quareo enabled component in the network enabling immediate recognition of a patch cord upon installing or removing. CPID gives network operators complete visibility to all connection events in the network and provides detailed information on the network elements being used. Adapter Packs and Modules Adapter packs are designed to provide easy connector insertion/removal, and clearer adapter port identification. Adapter packs are available in 24-fiber (12 duplex) LC, 12 fiber SC*, MPO-LC modules or eight MPO adapter pack configurations. Each tray supports one adapter pack, for a total of six adapter packs per shelf. These adapter packs can be included with the shelf. * Under development. Contact CommScope for information on availability of the SC variant. Quareo Rack Controller The Quareo rack controller is a networked device that provides power and communication means to the FIST- GPSQ shelves, and allows communication over the LAN network with the Quareo software or middleware. 7 For more information, visit

8 Example Application of a Two Rack Cross Connect NETWORK CONNECTION One CAT6 ethernet cable required per rack controller. To be connected to the network via a router or switch (likely outside the ODF room). GR3 RACK Rack Sideducts Doors CPID CORDS RACK CONTROLLER One Q-GF1-CTR Rack Controller can handle 1 rack of up to 16 subracks. Requires external power supply and network connection Power and communication cabling to each shelf using a star topology. Each controller port to be connected to the corresponding shelf. FIST-GPSQ - Managed Shelf Quareo Managed Patch Cords; matching CPID information at both ends 8 For more information, visit

9 FIST-GPSQ Shelf Featuring Quareo Technology (FIST-GPSQ) FIST-GPSQ shelves feature the FIST fiber management system and provide a platform for patching and splicing within a rack environment, using the Quareo physical layer management technology. The shelves house FIST splice and patch trays with Quareo CPID enabled adapter packs, available in LC, SC* and MPO. In addition different value adding modules are available including LC-MPO and precabled solutions. The shelves mount in FIST-GR3 racks. * Under development. Contact CommScope for information on availability of the SC variant. Quareo enabled Each connector position inside the FIST-GPSQ shelf can read CPID information from the Quareo enabled patch cords. This enables the shelf to discover all connector insertion and removal events, and automatically document connections in the Quareo ICM software or middleware. The FIST-GPSQ shelf itself, each tray inside the shelf, and each connector position inside the trays are equipped with LEDs. These LEDs help to guide technicians to the right patch ports, can give instant feedback during work order execution, and can visualize alarm conditions on unplanned connector insertions or removals. Features Patching, using patch cords, connectorized breakout or intrafacility cables Splicing loose tube cables, non-connectorized intrafacility or breakout cables to pigtails and patching these pigtails to patch cords Full patching capability on the tray and between trays in one shelf Use of connectorized cables allows repair of pigtails Kits available to attach cables at the side or back of shelf Wrap-around side panel and pigtail guide for easy re-patching Can be installed in CommScope s FIST-GR3 rack Shelves are shipped with the maximum number of trays and adapter packs already installed, or can be empty for use with Quareo cabled modules 9 For more information, visit

10 Connecto r Connecto r FIST-GR3 Benefits of Tray Patching Clean: Both sides easily accessible for cleaning adapters Safe: Laser light oriented perpendicularly to the operator Accessible: Full front access at both sides of connection Visible: Patch cords do not hamper access or visibility of ports Reconnection to other positions in the same tray or shelf does not result in uncontrolled overlengths Bend controls guide and protect the pigtail cable and ensure controlled cable routing Manipulation of patch cords does not cause transient losses Secure: because of their position in the trays, connectors are better protected than in some front facing patch shelves Dimensions, Configurations and Capacities Dimensions in mm: Height: 125 (3HU) Width: 385 Depth: 280 Tray Configuration Patch-Patch (AA) Splice-Patch (AX) Module (MA-AM) LC SC Future option Future option Future option Future option MPO N/A N/A Connector Capacity LC SC MPO Tray Shelf Rack (14 Shelves) For more information, visit

11 FIST-GPSQ Standard Kit Content Features Metal chassis with drawer Mounting brackets Drawer includes: -- 6 trays -- 2 tray support wedges -- Hook and loop strap to secure the trays -- Bend control(s) at the patching side for patch configurations Splice/patch versions include foam and tie-wraps to fix the cable elements (loose tubes, break-out cable, intra-facility subunits) onto the trays Trays which include: -- Adaptor packs (as configured) - - Pigtails if prefibered option -- Splice protector holder (only if configured as splice tray) -- Splice protectors (only if pigtail and SMOUV option is included) One or two trumpets for guiding pigtails as they exit the shelf Metal front cover: mm high version hingeable and removable cover Mounting screws and nuts Installation instructions 11 For more information, visit

12 Ordering Information FIST GPSQ Q - XX X XX - 6 Chassis Type 6 Trays Q 15 3 ETSI HU Tray Options (patch islands & modules) Connector Type (patch side) Right of Left of LU SU MU M1 Recommended for patch patch applications (AA) LC universal (black) SC universal (black) MPO - 12F universal (black) MPO-24F (aqua) Required specification for prefibered splice-patch (Ax) shelf (1) shelf (2) AA Patch only AI IA Splice patch - ANT - prefibered pigtails AJ JA Splice patch - ANT - prefibered pigtails AE EA Splice patch - SMOUV - no pigtails AF FA Splice patch - ANT -no pigtails AM MA Prepared to accept LC-MPO and precabled modules(3) L1 L2 LF LG L5 S1 S2 S3 SF SG S5 M1 M2 M3 M4 NN SM - LC - UPC - grade C SM - LC - APC - grade C SM - LC - UPC - grade B SM - LC - APC - grade B MM - LC - UPC SM - SC - UPC - grade C SM - SC - APC8 - grade C SM - SC - APC9 - grade C SM - SC - UPC - grade B SM - SC - APC8 - grade B MM - SC - UPC SM - MPO12 SM - MPO24 MM - MPO12 MM - MPO24 No connector specified 1 Patch cords or cables leave shelf to right; patch fiield to left of tray 2 Patch cords or cables leave shelf to left; patch fiield to right of tray 3 In this configuration modules have to be ordered separately Items to be ordered separately: Fusion splice protectors (according to type of tray chosen) Pigtails, patch cords, breakout and IFC (OCI, OCJ, OCIP) Contact CommScope for SC connector availability. Adapter Pack Quareo Enablement Group termination unit if non-connectorized breakout cable is to be used (FIST-GTU2) O L Empty Simplex Both Sides D Duplex Both Sides EDuplex Patch Side Only F Simplex Patch Side Only 12 For more information, visit

13 MPO Modules The MPO module offers a craft-friendly interface for connecting 24 LC connectors to an MPO adapter enabling a rapid connection to electronics or a fiber tie panel such as CommScope s Rapid Fiber panel solution. Leveraging an MPO architecture, technicians can route and install higher fiber counts faster and easier, while simplifying cable inventory and ordering requirements. MPO modules are available for use in the FIST-GPSQ-shelf, using the AM or MA tray configurations. For the AM configuration, with patch cords leaving to the right, and MPO trunk feeding from the left of the rack, use a left module. For the MA configuration, with patch cords leaving to the left, and MPO trunk cable feeding from the right of the rack, use a right module. Specifications MPOptimate Performance Multimode 12f MPO LC: Multimode 24f MPO LC: Singlemode Performance: Insertion & Return Loss: Traceable: Standard Fiber Path: 24-Fiber Trunk Compatible: Pinned Cassettes: Used in Pairs: Factory measured 0.35 db loss maximum per MPO-LC OM4 module Factory measured 0.35 db loss maximum per MPO-LC OM4 module < nm/1550 nm IL <= 0.35dB RL >= 27dB Each module is uniquely identified and linked to factory measurement data Compatible with TIA 568-C.0-2 draft standard for Method A Fiber path supports 24-fiber deployment MPO alignment pins are maintained inside the module, reducing damage risk Assures proper fiber map, polarity and location of MPO alignment pins 13 For more information, visit

14 Ordering Information Module Orientation Adapter Color LC Port Monitoring Polarity Part Number Left QE-MPM-24HPCUMLA Simplex A-A/B-B (Straight) Right QE-MPM-24HPCUMRA LC-to-MPOptimate (2x12-fiber MPO) Multimode MPOptimate (OM4); Loss (< nm/1300 nm) Left Right Left Black Duplex A-A/B-B (Straight) QE-MPM-24HPDUMLA QE-MPM-24HPDUMRA QE-MPM-24HPFAHLA A-A/B-B (Straight) Right QE-MPM-24HPFAHRA Aqua Duplex Left A-B/B-A (Straight) QE-MPM-24HPFAHLB Right QE-MPM-24HPFAHRB LC-to-MPOptimate (1x24-fiber MPO) Left A-A/B-B (Straight) QE-MPM-24HPFAJLA Multimode MPOptimate (OM4); Right QE-MPM-24HPFAJRA Loss (< nm/1300 nm) Left QE-MPM-24HPFAJLB Aqua Duplex A-B/B-A (Flipped) Right QE-MPM-24HPFAJRB Left 10G HD QE-MPM-24HPFAJLG Right QE-MPM-24HPFAJRG LC-to-MPO (2x12-fiber MPO) Left QE-MPM-24HPKUELA Singlemode; Loss (< nm/1550 nm) Right Simplex UPC A-A/B-B (Straight) QE-MPM-24HPKUERA Black Left Simplex APC A-A/B-B (Straight) QE-MPM-24HPMUELA Right QE-MPM-24HPMUERA Left Right Blue Duplex UPC A-A/B-B (Straight) QE-MPM-24HPCBELA QE-MPM-24HPCBERA Example of a MA tray configuration using a Right module Example of a AM tray configuration using a Left module

15 14 For more information, visit

16 Adapter Packs Adapter packs will generally be fitted on the trays of a FIST-GPSQ shelf, but can also be ordered separately. Universal adapter packs are designed to accept a variety of connector types, including singlemode and multimode, angled and ultra-polished connections, allowing a network operator to support all variants of connector type within a single adapter pack, greatly simplifying ordering and providing excellent future flexibility.. The flexibility of the black universal adapter pack helps service providers reduce ordering SKU s and total inventory requirements. The staggered adapter pack design helps installers access connectors without pinching or moving adjacent connections and helps clearly identify individual fiber ports. One 24-fiber (12 duplex port) LC adapter pack can be installed per tray or one eight-port MPO adapter pack (12- or 24-fiber MPO) per tray; up to six total adapter packs per shelf. Description Managed Adapter Pack, LC-LC Black, 24 fibers (24 simplex ports, managed both sides) Part Number QE-ADP-24HPLCS000 Managed Adapter Pack, LC-LC Black, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HPLCD000 Managed Adapter Pack, LC-LC Black, 24 fibers (12 duplex ports, managed patch side only) QE-ADP-24HPLCE000 Managed Adapter Pack, LC-LC Black, 24 fibers (24 simplex ports, managed patch side only) QE-ADP-24HPLCF000 Managed Adapter Pack, LC-LC Aqua, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HP0CD000 Managed Adapter Pack, LC-LC Blue, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HP0KD000 Managed Adapter Pack, LC-LC Green, 24 fibers (12 duplex ports, managed both sides) QE-ADP-24HP0MD000 Managed Adapter Pack, MPO-MPO Black, 96 fibers (8, 12F MPO, managed both sides) QE-ADP-96HPMPG000 Managed Adapter Pack, MPO-MPO Black, 96 fibers (8, 12F MPO, managed patch side only) QE-ADP-96HPMPF000 Managed Adapter Pack, MPO-MPO Aqua, 192 fibers (8, 24F MPO ports, managed both sides) QE-ADP-192HPMAG000 Managed Adapter Pack, MPO-MPO Green, 192 fibers (8, 24F MPO ports, managed both sides) QE-ADP-192HPMGG For more information, visit

17 FIST-GR3 Rack All-purpose, easy-to-assemble FIST-GR3 and FIST-GR3F racks accommodate the FIST fiber management system in a central office, head-end or customer premises environment. Several versions of the rack are available: one series based on the ETSI standard (600 mm wide); and one on the 15-inch standard (450 mm wide). With the addition of side ducts, total width of the rack framework varies between 600 and 1200 mm. Rack heights of 1.8 or 2.2 meters are available. All versions feature flexible shelf spacing and accept a range of accessories such as panels and doors to complete the installation. Both racks house connector panels and separate shelves for splicing, patching, equipment and devices. The racks allow superior management and storage of pigtail and patch cord overlengths. ** If you order a 19 frame, you will also need to order adapter brackets to fit the 15 Quareo FIST-GPSQ shelf. Features Easy handling Compact, efficient packaging means less waste Easy to transport, store, handle and install due to compact design Universal installation manual (drawings, no words) Assembly requires only simple tools allowing faster installations than standard racks Flexibility Compatible with CommScope s FIST-GR2 racks Accepts CommScope s Quareo FIST-GPSQ shelves; FIST-GSS2/GPS2 and FIST-GSS3/GPS3 shelves Depth and width in accordance with ETSI ETSI mounting profiles with cage nuts for shelf mounting provided at rear of the rack for optimal access from the front Optional units allow horizontal and vertical patch cord management and storage of excess patch cord overlength Bend control on all fiber routing All-purpose rack Structured division and distribution of cable elements Wide variety of optional accessories Extra cable attachment plates can be mounted in any location (top/bottom) in side duct Easy access to cables, pigtails and jumpers during installation, maintenance and upgrade Easy adaptation to specific applications by changing rack or shelf configuration, as well as routings of pigtails and jumpers Various mounting options -- Wall mounting, stand-alone or multiple side-to-side mounting (optional kit) -- Back-to-back mounting Various rack options to suit all application requirements -- Different side ducts (150, 300 mm) with drums for proper fiber management -- Different doors -- Front mounting options -- Depth extension kits -- Overlength storage bays 16 For more information, visit

18 Dimensions Dimensions (mm) and capacity Dimensions Capacity Description H1 W2 D3 Height Units (ETSI)3 Number of FIST Shelves 11 (3 HUs = 125mm = 5 ETSI HUs) FIST-GR3(F)-R-X =56 14 (2 HUs = 88mm = 4 ETSI HUs)4 28 (1 HU = 44mm = 2 ETSI HUs)4 11 (3 HUs = 125mm = 5 ETSI HUs) FIST-GR3(F)-R-X =72 14 (2 HUs = 88mm = 4 ETSI HUs)4 28 (1 HU = 44mm = 2 ETSI HUs)4 1 Rack height of 2.6m possible; for pricing, order quantities and availability please contact your CommScope sales representative 2 The width ( mm) depends on the configuration: please contact your CommScope sales representative 3 The base duct included in the rack occupies 8 ETSI HUs. If the base duct is removed, extra shelves can be placed in the rack 4 Not available with Quareo technology Racks D All racks include: 2 side ducts with integrated ETSI mounting profiles: manage and house cables, pigtails, patch cords H Base duct occupies 8 ETSI height units Loose drums Cable attachment plates and drum plates integrated into management panel Wall and back-to-back connection kits W1 W2 W3 WTOT Earthing kit Adjustable feet Installation instructions and footprint template Rack painted (powder coated) light grey (RAL-7035) 17 For more information, visit

19 Dimensions (in mm) Side Duct (W1) Central Section (W2) Side Duct (W3) Total Width (WTOT) Height (H) Depth (D) Description1 0 (pole) (pole) / FIST-GR3-R-0/0-XX-2 0 (pole) / FIST-GR3-R-0/150-XX-2 0 (pole) / FIST-GR3-R-0/300-XX / FIST-GR3-R-150/150-XX / FIST-GR3-R-150/300-XX / FIST-GR3-R-300/300-XX-2 0 (pole) / FIST-GR3F-R-0/150-XX-2 0 (pole) / FIST-GR3F-R-0/300-XX / FIST-GR3F-R-150/150-XX / FIST-GR3F-R-150/300-XX / FIST-GR3F-R-300/300-XX-2 1 For height, replace xx with 18 for 1800mm or 22 for 2200mm. For 2.6m racks, please contact your CommScope sales representative Accessories Description FIST-ODF-MB2-QT/M-AS FIST-ODF-MB2-QT/I-AS-FTB EG &4HU 15>ETSI 3&4HU 15>19 Mounting Bracket to mount a 15 3&4HU shelf into an ETSI rack. Asymmetrical Mounting Bracket to mount a 15 3&4HU shelf into a 19 rack. Asymmetrical front to back mounting (not recommended) **Doors, top covers, mounting brackets and storage bays are available. See GR3 ordering guide. 18 For more information, visit

20 Quareo Rack Controller The Quareo rack controller is a networked device that provides power and communication means to the FIST-GPSQ shelves, and allows communication over the LAN network with the Quareo physical layer network documentation solutions. Features Rack Controller Controls up to 16 FIST-GPSQ shelves Easy mounting inside GR3 rack top bar, or with separate mounting brackets Built-in 10/100Mbit/s Ethernet switch for daisy chaining of different racks in a line up 48VDC Power Supply with redundant A and B inputs Specifications Mounting bar Dimensions W x H x D 308mm x 42mm x 169mm (including led cover) Weight Power Supply 1.5kg 2 x 48V DC inputs A and B for redundancy Fused and breaker protected Power Consumption (Maximum) 28W, 1.5A Power Adapter Power Supply & Communication to FIST-GPSQ Shelves Cooling Ethernet Star topology, single connector per shelf. Connects up to 16 shelves. Natural convection cooling. No active cooling or fan. Built in Ethernet switch. 10/100 Mb/s. 2 x RJ45 connectors. Connection Cable Ordering information Description Quareo Rack Controller 1 Per GR3 FIST-GR3 mounting bar for Quareo Rack Controller - 15 (450mm), including mounting brackets FIST-GR3 mounting bar for Quareo Rack Controller - ETSI size (600mm), including mounting brackets Power brick for Quareo Rack Controller VAC to 48VDC. Power cord not included Cabling kit to connect Quareo Rack Controller and 14 Quareo subracks, labelled 1 to 14 Cabling kit to connect Quareo Rack Controller and 8 Quareo subracks, labelled 1 to 8 Cable kit to connect Quareo Rack Controller and 1 Quareo subrack, 3.1m long Catalog Number Q-GF1-CTRFB00000 Q-GF1-ACCFGR30450 Q-GF1-ACCFGR30600 Q-GF1-ACCFPBR0000 Q-GF1-ACCPCK0014 Q-GF1-ACCPCK0008 Q-GF1-ACCPCK For more information, visit

21 Quareo Managed Patch Leads and Multi-Fiber Cable Assemblies Different cable solutions are available to cable the FIST-GPSQ shelf. Depending on the application and fiber count an optimal solution can be provided. CommScope offers: Quareo Managed patch Leads -- Simplex and Duplex LC, SC* and MPO -- Made to length with increments of 10cm Multi-Fiber Cable Assemblies -- Stranded and Ribbon cable -- IFC, Trunk and microcable assemblies - - Connectorised, stubbed or with fanout -- Different Breakout lengths optimized for use in the GPSQ shelf, other Quareo panels (QHDEP, Q4000,...) and active equipment Features -- SC, LC connectors in PC or APC -- MPO12 and MPO24 for 10/40/100 migration, MPOptimate performance -- Multimode and singlemode (aqua and yellow) -- Standard colors: aqua for multimode, yellow for singlemode -- Standard materials: Plenum LSZH -- Performance specifications: ANSI/TIA-568-C.3 and ISO 11801, Edition 2 for OM3/OM4 multimode, OS1 for singlemode Contact CommScope to assist you in providing the best solution for your application. 20 For more information, visit

22 21 For more information, visit

23 www. Visit our website or contact your local CommScope representative for more information CommScope, Inc. All rights reserved. FIST, Rapid Fiber, Quareo, MPOptimate and all trademarks identified by or are registered trademarks or trademarks, respectively, of CommScope, Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. CA AE (12/15)